The World Models E326 Paulistinha P-56 EP Instruction Manual

THE WORLD MODELS PAULISTINHA P-56 EP is an almost-ready-to-fly (ARF) aircraft designed for experienced modelers. With a wingspan of 48.5 inches and a flying weight of 28 ounces, it's powered by a KM0283011 Outrunner Motor and a 3-cell 11.1V 15C 1800 mAh Li-Po battery. The plane features ailerons, elevator, rudder, and steerable nose wheel for precise control. The lightweight construction and durable materials make it suitable for a wide range of flying conditions, from gentle aerobatics to sport flying.

PDF Download

Document

INSTRUCTION MANUAL

(E326)

Requires: 4-channel radio w/ 4 micro servos. Outrunner

Motor KM0283011 w/ Propeller Adaptor HW2340100

20A Brushless ESC, 3 cells 11.1V 15C 1800 mAh Li-Po

battery & charger.

Specifications

Wing Span 48.5 in / 1230 mm

Wing Area 330 sq in / 21.3 sq dm

Flying Weight 28 oz / 800 g

Fuselage Length 30 in / 760 mm

* Specifications are subject to change without notice. *

Warning! This model is not a toy.

It is designed for maximum performance. Please seek advice if one is not familiar with this kind of engine powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference.

E326PO28761301

The World Models w w w. t h e w o r l d m o d e l s . c o m

FACTORY PRE-FABRICATED

ALMOST-READY-TO-FLY (ARF) SERIES

MADE IN CHINA

INDEX

BEFORE YOU BEGIN

PARTS LIST

ASSEMBLY

SAFETY PRECAUTIONS

BEFORE YOU BEGIN

P.1

P.2 P.3-P.10

P.10

1 Read through the manual before you begin, so you will have an overall idea of what to do.

2 Check all parts. If you find any defective or missing parts contact your local dealer. Please

DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.

Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement. The manufacturer will replace any defective parts, but will not extend to the parts that are good before gluing to defective parts during assembly. Warranty will not cover any parts modified by customer.

3 Symbols used throughout this instruction manual comprise of the following :-

Apply epoxy glue.

Apply instant glue

(C.A.glue, super glue.)

Apply thread locker Must be purchased separately !

Assemble left and right sides the same way.

Peel off shaded portion covering film.

3mm

Drill holes with the specified diameter (here: 3mm).

Pay close attention here!

E326PO28761301 P.1

Ensure smooth non-binding movement while assembling.

Cut off shaded portion.

Pierce the shaded portion covering film.

Warning!

Do not overlook this symbol !

Parts List

1. MAIN WING -- 1 pair

2. MICRO AILERON SERVO MOUNT (For Aileron) PL5310020 -- 1 pair

CLEVIS PL4112105 -- 2 pcs

STRAPER PL4112106 -- 2 pcs

FUEL TUBE d2xD4x4mm -- 4 pcs

SCREW PB2x14mm -- 4 pcs

SCREW PA1.7x8mm -- 8 pcs

PUSHROD D1.4x69mm w/ Threads (For Aileron) -- 2 pcs

HORN PL4113102 -- 2 sets

WING JOINER 5x13x82mm -- 1 pc.

3. STABILIZER & ELEVATOR -- 1 set

FUSELAGE -- 1 pc.

ELEVATOR LINK PL4510010 -- 1 set

SCREW PB2x8mm -- 2 pcs

BALSA 3.5x6x7.5mm -- 1 pc.

4. VERTICAL FIN & RUDDER -- 1 set

5. TAIL LANDING GEAR PL3410030 -- 1 set

TAIL WHEEL Ø23mm -- 1 pc.

PLASTIC COLLAR Ø1.1mm w/ set screw -- 2 pcs

SCREW PA2x8mm -- 2 pcs

SCREW PM2x8mm -- 1 pc.

M2 NUT -- 1 pc.

ALUMINUM PLATE 0.3mm -- 1 pc.

6. SCREW PB2x8mm -- 2 pcs

CLEVIS PL4112105 -- 1 pc.

FUEL TUBE d2xD4x4mm -- 1 pc.

HORN PL4113102 -- 1 set

PUSHROD Ø1.4x413mm w/ Threads (For Rudder) -- 1 pc.

7. CLEVIS PL4112105 -- 1 pc.

FUEL TUBE d2xD4x4mm -- 1 pc.

PUSHROD Ø1.4x403mm w/ Threads (For Elevator) -- 1 pc.

8. SOCKET HEAD SCREW M3x6mm -- 4 pcs

WASHER d3xD7mm -- 4 pcs

SPINNER Ø28mm -- 1 set

9x6 FOLDING PROPELLER SET PL6313031 -- 2 pcs

COWLING -- 1 pc.

SCREW PWA2x8mm -- 4 pcs

9. WINDOWS -- 1 set

SCREW PWA2x8mm -- 4 pcs

E326PO28761301 P.2

10. SPONGE 10x50x150mm -- 2 pcs

DOUBLE-SIDED TAPE 30x35mm -- 1 pc.

FUEL TUBE d2xD4x4mm -- 2 pcs

BATTERY TIE 200mm-- 1 pc.

STRAPER PL4112106 -- 2 pcs

11. MAIN LANDING GEAR Ø2.5mm -- 1 set

MAIN WHEEL Ø50mm -- 2 pcs

LANDING WIRE STRAPS PL4114030 -- 3 pcs

PVC PLATE 32x6mm (For Main Landing Gear) -- 2 pcs

BALSA 2x73x80mm (Main Landing Gear Cover) -- 2 pcs

SCREW PA2.6x10mm -- 6 pcs

COLLAR Ø2.6mm w/ Set Screw -- 4 sets

SCREW PM2x6mm -- 4 pcs

WASHER d2xD5mm -- 5 pcs

M2 NUT -- 4 pcs

TRANSPARENT DECALS 20x70mm -- 4 pcs

SCREW PM2x10mm -- 1 pc.

M2 NYLON INSERT LOCK NUT -- 1 pc.

MOUNTING PLATE PL4114015 -- 1 pc.

PLYWOOD 2x60.7x62.7mm -- 1 pc.

12. SCREW PM2.5x25mm -- 2 pcs

WASHER d2.5xD8mm -- 2 pcs

WING PROTECTION PLATE 6x25x82mm -- 1 pc.

13. SCREW PA2.3x8mm -- 6 pcs

WING STRUTS -- 1 pair

14. DECALS: E326DEC -- 1 set

COVERING:

LIGHTEX SGX 201 BLACK

LIGHTEX SGX 310 RED

LIGHTEX SGX 204 CREAM

1 Main Wing

Apply instant type CA glue to both sides of each hinge.

Aileron Servo Lead

Bottom View

Aileron Servos

PB2x14mm Screw

PA1.7x8mm

Screw

Ø1mm pilot holes for World

Models horn are pre-drilled.

Please look for pin-hole marks at under side of control surfaces.

02L

03L

04L

Straper

Fuel Tube d2xD4x4mm

02R

03R

04R

TWM PL8210010

CLEVIS WRENCH

PA1.7x8mm

PB2x14mm

Pushrod

Ø1.4x69mm

Horn

Clevis

Fuel Tube

d2xD4x4mm

Bottom View

Please dry fit wing joiner into left and right wing to make sure they fit with the proper dihedral angle, mark the wing joiner if necessary. Apply epoxy glue to both sides of all surfaces in contact. Use a stick to apply the glue to inner side of wing joiner sleeve, and apply the glue to wing joiner before putting them together. Wing joiner not glued properly will lead to wing failure and plane crash.

Wing Joiner 5x13x82mm

Bottom View

Please choose either (02L&02R) or (03L&03R) or (04L&04R) that suits your servo.

E326PO28761301 P.3

Stabilizer & Elevator

PB2x8mm Screw

Remove coverings for all surfaces in contact before applying A/B epoxy glue.

A=A'

Temporary install the main wing, adjust leveling of the stabilizer to make it as parallel to the main wing as possible .

(Stabilizer)

(Main Wing)

B=B'

Balsa 3.5x6x7.5mm

PB2x8mm

Ø1mm pilot holes for World Models horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces.

Apply instant type CA glue to both sides of each hinge.

Vertical Fin & Rudder

C C'

C=C'

Apply instant type CA glue to both sides of each hinge.

Remove coverings for all surfaces in contact before applying A/B epoxy glue.

Completed

E326PO28761301 P.4

Tail Landing Gear

PA2x8mm Screw

PM2x8mm Screw

M2 Nut

Steering Bracket

PM2x8mm

Wheel Ø23mm

PA2x8mm

Bottom View

Rudder Pushrod

PB2x8mm Screw

Ø1mm pilot holes for World Models horn are pre-drilled.

Please look for pin-hole marks at under side of control surfaces.

TWM PL8210010

CLEVIS WRENCH

Horn

Clevis

Pushrod

Ø1.4x413mm

PB2x18mm

Fuel Tube d2xD4x4mm

Bottom View

Elevator Pushrod

TWM PL8210010

CLEVIS WRENCH

Pushrod

Ø1.4x403mm

Clevis

Bottom View

E326PO28761301 P.5

Outrunner Motor / Cowling

M3x6mm Socket Head Screw

PM2x12mm Screw

PA1.7x8mm Screw

2 d3xD7mm Washer

PWA2x8mm Screw

ESC

Solder

Optional Parts

Make sure rotating motor casing is not in contact with wirings or anything.

Propeller Adaptor

(d3xD5) HW2340100

Solder

Motor

TWM

KP0011310

Don't over-tighten the M3 screws, too much stress on the screws could split the firewall.

Washer d3xD7mm

M3x6 mm

Propeller Adaptor Wrench

TWM HW3111400

EZ Connector

PM2x12mm

9x6mm PL6313031

Don’t over-tighten the PM2 screws, let the propeller blades align themselves when spinning.

E326PO28761301

PWA2x8 mm

TWM HW3111400

PROPELLER ADAPTOR WRENCH

P.6

PA1.7x8mm

Ø28mm Spinner

Completed

Windows

PWA2x8mm Screw

Securely glue the windows to the fuselage.

PWA2x8mm

10 Radio Equipment

Rudder Pushrod

Straper lnstall and arrange the servo as shown in the diagram.

Front

Fuel Tube d2xD4x4mm Rudder Servo

Battery

Elevator Pushrod

Receiver

Battery Tie

Sponge

Elevator Servo

Battery Tie Battery Sponge

E326PO28761301

Sponge

Bottom View

P.7

Brushless ESC

Double Sided Tape

11 Main Landing Gear

PM2x10mm Screw

PM2x6mm Screw

PA2.6x10mm Screw

M2 Nut

4 d2xD5mm Washer

D2.6mm

Collar

M2 Nylon Insert Lock Nut

Landing Gear Cover

PM2x6mm

Washer d2xD5mm

Mounting Plate

PM2x10mm

PVC32x6mm

M2 Nut

Fuselage

Washer d2xD5mm

M2 Nylon

Insert Lock Nut

Bottom View

Battery Cover

Main Wing

PM2.5x25mm Screw

2 d2.5xD8mm

Washer

PA2.6x10mm

Landing Gear Cover

70x20mm

Transparent Decals

Wheel Ø 50mm

M3 x 3mm

Set Screw

2.6 mm Collar 2.6 mm Collar

Washer d2.5xD8mm

PM2.5x25mm

Wing Protection Plate

Wing Struts

PA2.3x8mm Screw

1mm

E326PO28761301

Bottom View

P.8

PA2.3x8mm

Wing Setting

Adjust the wing and fuselage configuration as shown in the diagrams.

A A '

A = A '

E326PO28761301

B B '

C '

P.9

B = B ' C = C '

Control Throws

Rudder

Elevator

Aileron

25mm

Adjust the control throws as shown in the diagram.

These throws are good for general flying. You can adjust according to your personal preference.

15mm

10mm

C

G

The ideal C.G. position is 50mm (2.0 in.) behind the leading edge measured at where the wing meets the fuselage. In order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying.

50 mm

2.0 in.

C.G.

http://www.theworldmodels.com/para/instruction/instructionManuals.php

Warning!

Important Safety Precautions

# First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary.

# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft.

KM0283011 Outrunner Motor .

# Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running

propeller. Extreme caution should be exercised when working with electric powered models. Make sure the

propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure

you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you

plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental

movement of the throttle stick will spin the propeller and could cause injuries.

# If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles.

Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone.

Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the

glue and shrink the covering at the same time, causing the seams to pull away.

# Check and re-tighten up all factory assembled screws, use thread locker if necessary.

E326PO28761301 P.10

Pl8210010

KM0283011

E326PO28761301

Hello! I am an AI chatbot specifically trained to assist you with the E326 Paulistinha P-56 EP Instruction Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated