Belkin | F5D8633-4 | User manual | Belkin F5D8633-4 User manual

N Wireless
Modem Router
User Manual
F5D8633-4
Table of Contents
1. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Advantages of a Wireless Network . . . . . . . . . . . . . . . . . . . 1
Placement of your N Wireless Modem Router . . . . . . . . . . . 3
2. Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3. Knowing your Modem Router . . . . . . . . . . . . . . . . . . . . . . . 11
Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Setup Assistant Software System Requirements . . . . . . . . 11
4. Connecting and Configuring your Modem Router . . . . . . . . 18
5. Alternate Setup Method . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6. Using the Web-Based Advanced User Interface . . . . . . . . . 42
Changing LAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Viewing the DHCP Client List Page . . . . . . . . . . . . . . . . . . 45
Configuring the Wireless Network Settings . . . . . . . . . . . . 45
Setting WPA Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Setting WEP Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Using the Access Point Mode . . . . . . . . . . . . . . . . . . . . . . 55
Setting MAC Address Control . . . . . . . . . . . . . . . . . . . . . 56
Configuring the Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Using Dynamic DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Restarting the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Updating the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . 69
7. Manually Configuring Network Settings . . . . . . . . . . . . . . . 77
8. Recommended Web Browser Settings . . . . . . . . . . . . . . . . . 82
9. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
10. Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Introduction
•
Share one high-speed Internet connection with all the computers in
your home
•
Share resources, such as files and hard drives among all the
connected computers in your home
•
Share a single printer with the entire family
•
Share documents, music, video, and digital pictures
•
Store, retrieve, and copy files from one computer to another
•
Simultaneously play games online, check Internet email, and chat
Advantages of a Wireless Network
Here are some of the advantages of setting up a Belkin
Wireless Network:
•
Mobility – you’ll no longer need a dedicated “computer
room”—now you can work on a networked laptop or desktop
computer anywhere within your wireless range
•
Easy installation – Belkin’s Easy Installation Wizard makes
setup simple
•
Flexibility – set up and access printers, computers, and other
networking devices from anywhere in your home
•
Easy expansion – the wide range of Belkin networking products let
you expand your network to include devices such as printers and
gaming consoles
•
No cabling required – you can spare the expense and hassle of
retrofitting Ethernet cabling throughout the home or office
•
Widespread industry acceptance – choose from a wide range of
interoperable networking products
1
1
2
3
4
5
6
7
8
9
10
section
Thank you for purchasing the Belkin N Wireless Modem Router (the
Router). Following are two short sections—the first discusses the benefits
of home networking, and the other outlines best practices that maximize
your wireless home network range and performance. Please be sure to
read through this User Manual completely, and pay special attention to
the section entitled “Placement of your Wireless Networking Hardware for
Optimal Performance” on the next page. By following our simple setup
instructions you will be able to use your Belkin Home Network to:
Introduction
Revolutionary N Wireless Technology with MIMO (N MIMO)
Your Belkin N Wireless Modem Router uses a new smart-antenna technology
called Multiple Input Multiple Output (MIMO). N1 MIMO complies with the
IEEE draft 802.11n specification. It increases speed, range, reliability, and
spectral efficiency for wireless networking systems.
The element that makes Belkin’s N MIMO technology different from a
conventional radio is the use of multiple antennas and two simultaneous
data streams to deliver wireless transfers around your home or office. A
conventional radio uses one antenna to transmit a data stream. Belkin’s N
MIMO, on the other hand, uses two antennas. This design helps combat
distortion and interference. Belkin’s N MIMO is multidimensional. It builds
on one-dimensional smart-antenna technology by simultaneously
transmitting two data streams through the same channel, which increases
wireless capacity.
Another element that enhances Belkin’s N MIMO is the use of aggregation as
specified in the draft 802.11n specification. By shortening the space between
packets and combining multiple smaller packets into one larger packet, Belkin’s N
MIMO can transmit more data through available bandwidth.
Think of conventional radio transmission as a two-lane highway. The speed
limit governs the maximum allowable flow of traffic through that lane.
Compared with conventional radios, one-dimensional smart antenna systems
help move traffic through that lane faster and more reliably—analogous
to a four-lane road on which traffic consistently moves at a rate closer to
the speed limit. Belkin’s N MIMO helps traffic move at the speed limit and
opens more lanes—to become the superhighway in this example. The rate of
traffic flow is multiplied by the number of lanes that are opened.
2
Introduction
1
Important Factors for Placement and Setup
2
Your wireless connection will be stronger the closer your computer is
to your Router. Typical indoor operating range for wireless devices is
between 100 and 200 feet.
3
In the same way, your wireless connection and performance will degrade
somewhat as the distance between your Router and connected devices
increases. This may or may not be noticeable to you. As you move further
from your Router, connection speed may decrease. Factors that can weaken
signals simply by getting in the way of your network’s radio waves are metal
appliances or obstructions, and walls.
If you have concerns about your network’s performance that might
be related to range or obstruction factors, try moving the computer
to a position between five and 10 feet from the Router in order to see
if distance is the problem. If difficulties persist even at close range,
please contact Belkin Technical Support.
Note: While some of the items listed below can affect network
performance, they will not prohibit your wireless network from
functioning; if you are concerned that your network is not operating at
its maximum effectiveness, this checklist may help.
1.
Router Placement
Place your Router, the central connection point of your
network, as close as possible to the center of your wireless
network devices.
To achieve the best wireless network coverage for your “wireless
clients” (i.e., computers enabled by Belkin Wireless Notebook
Network Cards, Wireless Desktop Network Cards, and Wireless
USB Adapters):
•
Ensure that your Router’s networking antennas are parallel
to each other, and are positioned vertically (toward the
ceiling). If your Router itself is positioned vertically, point the
antennas as much as possible in an upward direction.
•
In multistory homes, place the Router on a floor that is as
close to the center of the home as possible. This may mean
placing the Router on an upper floor.
•
Try not to place the Router near a cordless 2.4GHz phone.
3
4
5
6
7
8
9
10
section
Placement of your N Wireless Modem Router
Introduction
2.
Avoid Obstacles and Interference
Avoid placing your Router near devices that may emit radio
“noise,” such as microwave ovens. Dense objects that can inhibit
wireless communication include:
• Refrigerators
• Washers and/or dryers
• Metal cabinets
• Large aquariums
• Metallic-based, UV-tinted windows
If your wireless signal seems weak in some spots, make sure that
objects such as these are not blocking the signal’s path (between
your computers and Router).
3.
Cordless Phones
If the performance of your wireless network is impaired after
attending to the above issues, and you have a cordless phone:
• Try moving cordless phones away from your Router and your
wireless-enabled computers.
• Unplug and remove the battery from any cordless phone
that operates on the 2.4GHz band (check manufacturer’s
information). If this fixes the problem, your phone may
be interfering.
• If your phone supports channel selection, change the channel
on the phone to the farthest channel from your wireless
network. For example, change the phone to channel 1 and
move your Router to channel 11. See your phone’s user
manual for detailed instructions.
• If necessary, consider switching to a 900MHz or 5GHz
cordless phone.
4
Introduction
Choose the “Quietest” Channel for your Wireless Network
In locations where homes or offices are close together, such as
apartment buildings or office complexes, there may be wireless
networks nearby that can conflict with yours.
Use the Site Survey capabilities found in the Wireless Utility of
your wireless adapter to locate any other wireless networks that
are available (see your wireless adapter’s user manual), and move
your Router and computers to a channel as far away from other
networks as possible.
• Experiment with more than one of the available channels, in
order to find the clearest connection and avoid interference
from neighboring cordless phones or other wireless devices.
• For Belkin wireless networking products, use the detailed Site
Survey and wireless channel information included with your
wireless network card. See your network card’s user guide for
more information.
These guidelines should allow you to cover the maximum
possible area with your Router. Should you need to cover an
even wider area, we suggest the Belkin Wireless Range
Extender/Access Point.
1
2
3
4
5
6
7
8
9
10
5
section
4.
Introduction
5.
Secure Connections, VPNs, and AOL
Secure connections typically require a user name and
password, and are used where security is important. Secure
connections include:
• Virtual Private Network (VPN) connections, often used to connect
remotely to an office network
• The “Bring Your Own Access” program from America Online (AOL),
which lets you use AOL through broadband provided by another
cable or DSL service
• Most online banking websites
• Many commercial websites that require a user name and password to
access your account
Secure connections can be interrupted by a computer’s power
management setting, which causes it to “go to sleep.” The simplest
solution to avoid this is to simply reconnect by rerunning the VPN or
AOL software, or by re-logging into the secure website.
A second alternative is to change your computer’s power management
settings so it does not go to sleep; however, this may not be
appropriate for portable computers. To change your power management
setting under Windows, see the “Power Options” item in the Control
Panel.
If you continue to have difficulty with Secure Connections, VPNs, and
AOL, please review the steps above to be sure you have addressed
these issues.
6
Introduction
You can find additional support information on our website at
www.belkin.com through the tech-support area.
2
If you want to contact technical support by phone, please call the
number you need from the list below*.
3
*Local rates apply.
Country
Number
Internet adress
AUSTRIA
0820 200766
http://www.belkin.com/uk/networking/
BELGIUM
07 07 00 073
http://www.belkin.com/nl/networking/
CZECH REPUBLIC
239 000 406
http://www.belkin.com/uk/networking/
DENMARK
701 22 403
http://www.belkin.com/uk/networking/
FINLAND
00800 - 22 35 54 60
http://www.belkin.com/uk/networking/
FRANCE
08 - 25 54 00 26
http://www.belkin.com/fr/networking/
GERMANY
0180 - 500 57 09
http://www.belkin.com/de/networking/
GREECE
00800 - 44 14 23 90
http://www.belkin.com/uk/networking/
HUNGARY
06 - 17 77 49 06
http://www.belkin.com/uk/networking/
ICELAND
800 8534
http://www.belkin.com/uk/networking/
IRELAND
0818 55 50 06
http://www.belkin.com/uk/networking/
ITALY
02 - 69 43 02 51
http://www.belkin.com/it/support/tech/issues_more.asp
LUXEMBOURG
34 20 80 85 60
http://www.belkin.com/uk/networking/
NETHERLANDS
0900 - 040 07 90
€0.10 per minute
http://www.belkin.com/nl/networking/
NORWAY
81 50 0287
http://www.belkin.com/uk/networking/
POLAND
00800 - 441 17 37
http://www.belkin.com/uk/networking/
PORTUGAL
707 200 676
http://www.belkin.com/uk/networking/
RUSSIA
495 580 9541
http://www.belkin.com/networking/
SOUTH AFRICA
0800 - 99 15 21
http://www.belkin.com/uk/networking/
SPAIN
902 - 02 43 66
http://www.belkin.com/es/support/tech/networkingsupport.asp
SWEDEN
07 - 71 40 04 53
http://www.belkin.com/se/support/tech/networkingsupport.asp
SWITZERLAND
08 - 48 00 02 19
http://www.belkin.com/uk/networking/
UNITED KINGDOM
0845 - 607 77 87
http://www.belkin.com/uk/networking/
OTHER COUNTRIES
+44 - 1933 35 20 00
7
4
5
6
7
8
9
10
section
1
Free Tech Support*
Product Overview
Product Features
In minutes you will be able to share your Internet connection and
network your computers. The following is a list of features that make
your new Belkin N Wireless Modem Router an ideal solution for your
home or small office network.
Works with Both PCs and Mac® Computers
The Router supports a variety of networking environments including
Mac OS ® 8.x, 9.x, X v10.x, Linux ®, Windows ® 98, Me, NT ®, 2000, XP,
and Vista . All that is needed is an Internet browser and a network
adapter that supports TCP/IP (the standard language of the Internet).
Patent-Pending Network Status Display
Lighted LEDs on the front of the Router indicate which functions
are in operation. You’ll know at-a-glance whether your Router is
connected to the Internet. This feature eliminates the need for
advanced software and status-monitoring procedures.
Web-Based Advanced User Interface
You can set up the Router’s advanced functions easily through your
web browser, without having to install additional software onto the
computer. There are no disks to install or keep track of and, best
of all, you can make changes and perform setup functions from any
computer on the network quickly and easily.
NAT IP Address Sharing
Your Router employs Network Address Translation (NAT) to share the
single IP address assigned to you by your Internet Service Provider
while saving the cost of adding additional IP addresses to your
Internet service account.
SPI Firewall
Your Router is equipped with a firewall that will protect your network
from a wide array of common hacker attacks including IP Spoofing,
Land Attack, Ping of Death (PoD), Denial of Service (DoS), IP with
zero length, Smurf Attack, TCP Null Scan, SYN flood, UDP flooding,
Tear Drop Attack, ICMP defect, RIP defect, and fragment flooding.
8
Product Overview
1
Integrated 10/100 4-Port Switch
Universal Plug and Play (UPnP)
2
3
4
UPnP is a technology that offers seamless operation of voice
messaging, video messaging, games, and other applications that
are UPnP-compliant.
5
Support for VPN Pass-Through
6
If you connect to your office network from home using a VPN
connection, your Router will allow your VPN-equipped computer to
pass through the Router and to your office network.
7
Built-In Dynamic Host Configuration Protocol (DHCP)
8
Built-In Dynamic Host Configuration Protocol (DHCP) on-board makes
for the easiest possible connection of a network. The DHCP server
will assign IP addresses to each computer automatically so there is no
need for a complicated networking setup.
9
10
Setup Assistant
The Setup Assistant, second generation of Belkin’s renowned Easy
Install Wizard, takes the guesswork out of setting up your Router.
This automatic software determines your network settings for you
and sets up the Router for connection to your Internet Service Provider
(ISP). In a matter of minutes, your Router will be up and running on the
Internet.
Note: Setup Assistant software is compatible with Windows 2000,
XP, Vista and Mac OSX 10.2, 10.3 and 10.4. If you are using another
operating system, the Router can beset up using the Alternate Setup
Method described in this User Manual (see page 30).
9
section
The Router has a built-in, four-port network switch to allow your wired
computers to share printers, data and MP3 files, digital photos, and
much more. The switch features automatic detection so it will adjust to
the speed of connected devices. The switch will transfer data between
computers and the Internet simultaneously without interrupting or
consuming resources.
Product Overview
Integrated N Wireless Access Point
N MIMO is an exciting new wireless technology based on the draft
IEEE 802.11n specification. It employs MIMO (Multiple Input Multiple
Output) smart-antenna technology that achieves data rates of up to
300Mbps.* Actual throughput is typically lower than the connected
data rate and will vary depending on your networking environment.
*NOTE: The standard transmission rate—300Mbps—is the physical
data rate. Actual data throughput will be lower.
MAC Address Filtering
For added security, you can set up a list of MAC addresses (unique
client identifiers) that are allowed access to your network. Every
computer has its own MAC address. Simply enter these MAC
addresses into a list using the Web-Based Advanced User Interface
and you can control access to your network.
10
Knowing your Modem Router
1
Package Contents
Belkin N Wireless Modem Router
•
Quick Installation Guide
•
Belkin Setup Assistant Software CD
•
RJ11 Telephone Cord
•
RJ45 Ethernet Networking Cable
•
ADSL (Asymmetric Digital Subscriber Line) Microfilter*
•
Power Supply
•
User Manual in CD
2
3
4
5
*ADSL microfilter varies by country. If it’s not included, you will need
to purchase one.
6
System Requirements
7
•
An active ADSL service with a telephone wall jack for
connecting the Router
•
At least one computer with an installed network interface adapter
•
TCP/IP networking protocol installed on each computer
•
No other DHCP server on your local network assigning IP
addresses to computers and devices
•
Internet browser
Setup Assistant Software System Requirements
•
A computer running Windows 2000, XP, or Vista;
or Mac OS X v10.x
•
Minimum 1GHz processor and 128MB RAM
•
Internet browser
11
8
9
10
section
•
Knowing your Modem Router
Internet Connection Settings
The Setup Assistant contains a database of Internet Service Providers
(ISP) in each country to help you set up your Router quickly. If your ISP
is not on the list, please collect the following information from your ISP
before setting up the Router:
•
Internet connection protocol:
Dynamic IP, Static IP)
•
Multiplexing method or Encapsulation:
(LLC or VC MUX)
•
Virtual circuit: VPI (Virtual Path Identifier)
(a number between 0 and 255)
•
VCI (Virtual Channel Identifier)
(a number between 1 and 65535)
•
For PPPoE and PPPoA users: ADSL account user name
and password
•
For static IP users: IP Address
Subnet Mask
.
.
.
.
Default Gateway Server
•
(PPPoE, PPPoA,
.
.
.
IP address for Domain Name Server
(If given by your ISP)
.
.
.
12
.
Knowing your Modem Router
(B)
(A)
(C)
(D)
(E)
(F)
1
2
3
4
5
6
A.
B.
C.
Wireless Security
OFF
Wireless security is off
Solid Blue
Wireless security is on
Wireless-Computer Status
OFF
Wireless computer is not present
Solid Blue
Wireless computer is connected to
the Router
Blinking Amber
Problem with wireless computer
connecting properly to the Router
Wired-Computer Status
OFF
Wired computer is not present
Solid Blue
Wired computer is connected to
the Router
Blinking Amber
Problem with wired computer connecting
properly to the Router
13
7
8
9
10
section
The Router has been designed to be placed on a desktop. All of the
cables exit from the rear of the Router for better organization and
utility. The Network Status Display is easily visible on the FRONT
of the Router to provide you with information about network activity
and status. See the Network Status Display Guide for more
detailed information.
Knowing your Modem Router
D.
Router/Power Status
When you apply power to the Router or restart it, a short period of
time elapses while the Router boots up. During this time, the “router”
icon blinks. When the Router has completely booted up, the “router”
icon becomes a solid light, indicating the Router is ready for use.
E.
OFF
Router is off
Blinking Blue
Router is booting up
Solid Blue
Router is on and ready
ADSL Line Status
This icon lights in blue to indicate that your Router is connected
properly to the ADSL. It turns amber when problem is detected.
OFF
Router is NOT connected to a
functioning ADSL line
Blinking Blue
Router is attempting to connect to
an ADSL service
Solid Blue
Router is connected to an ADSL service
and is functioning properly
Blinking Amber
Problem with ADSL line
14
Knowing your Modem Router
F.
1
Internet Status
OFF
Router is NOT connected to the Internet
Blinking Blue
Router is attempting to connect to
the Internet
Solid Blue
Router is connected to the Internet
Blinking Amber
Router is not connected to the Internet
2
3
4
5
6
7
8
9
10
15
section
This unique icon shows you when the Router is connected to the
Internet. When the light is off, the Router is NOT connected to the
Internet. When the light is blinking amber, the Router is attempting
to connect to the Internet. When the light is solid blue, the Router
is connected to the Internet. When using the “Disconnect after x
minutes” feature, this icon becomes extremely useful in monitoring
the status of your Router’s connection.
Knowing your Modem Router
G.
(G)
(H)
Connection to ADSL
– Gray
(I) (J)
(K)
This port is for connection to your ADSL. Connect your ADSL to
this port. An RJ11 telephone cord is provided in the package.
H.
Connections to Wired Computers
– Yellow
Connect your wired (non-wireless) computers to these ports.
These ports are RJ45, 10/100 auto-negotiation, auto-uplinking
ports for standard UTP category 5 or 6 Ethernet cable. The ports
are labeled 1 through 4, with onboard LEDs on the connectors.
16
Knowing your Modem Router
I.
1
Reset Button
i.
Resetting the Router
Push and release the “Reset” button. The lights on the
Router will momentarily flash. The “Power/Ready” light will
begin to blink. When the “Power/Ready” light becomes solid
again, the reset is complete.
ii.
Restoring the Factory Defaults
Press and hold the “Reset” button for at least 10 seconds,
then release it. The lights on the Router will momentarily
flash. The “Power/Ready” light will begin to blink. When
the “Power/Ready” light becomes solid again, the restore
is complete.
J.
Power Jack – Black
Connect the included 15V/.08A DC power supply to this jack.
K.
2
3
4
5
6
7
8
9
10
Push Button – White
This button is set aside for future upgradeable features. Please
check for the latest firmware updates at www.belkin.com/
support.
17
section
The “Reset” button is used in rare cases when the Router may
function improperly. Resetting the Router will restore the Router’s
normal operation while maintaining the programmed settings. You
can also restore the factory default settings by using the “Reset”
button. Use the restore option in instances where you may have
forgotten your custom password.
Connecting and Configuring your Modem Router
Verify the contents of your box. You should have the following:
•
Belkin N Wireless Modem Router
•
RJ11 Telephone Cord
•
RJ45 Ethernet Networking Cable
•
Power Supply
•
Belkin Setup Assistant Software CD
•
User Manual on CD
Setup Assistant
Belkin has provided our Setup Assistant software to make installing
your Router a simple and easy task. You can use it to get your Router
up and running in minutes. The Setup Assistant requires that your
Windows 2000 or XP computer be connected directly to your ADSL
and that the Internet connection is active and working at the time
of installation. If it is not, you must use the “Alternate Setup Method”
section of this User Manual to configure your Router. Additionally,
if you are using an operating system other than Windows 2000, XP,
or Vista, or Mac OS X v10.x, you must set up the Router using the
“Alternate Setup Method” section of this User Manual.
18
Connecting and Configuring your Modem Router
Step 1
Hardware Connections – Follow the Quick Installation
Guide (QIG)
1.1 Brand-New Setup
2
3
4
5
6
7
B.
C.
Retrieve the yellow RJ45 cable that
was included with your Router. First,
connect one end to any yellow port
labeled “to Wired Computers” on the
back of your Router. Then, connect
the other end to the networking port
on the back of your computer.
Retrieve the included gray RJ11
phone cord. Connect one end to
the gray port labeled “to ADSL”
on the back of your Router. Then
connect the other end to your ADSL
connection (either a wall jack or an
ADSL splitter).
Note: Some ADSL connections
require a microfilter. Your ADSL
provider can tell you if you need one.
Belkin includes a microfilter in regions
known to use them. You may or may
not have received one in your box.
19
8
9
10
section
Follow these steps if you are not replacing an existing modem.
If you are replacing an existing modem, skip to the next section,
“Replacing an Existing Modem or Modem Router”, starting on
page 20.
A. Unpack your new Router from
computer
the box and place it next to
your computer. Raise the
modem router
Router’s antennas.
1
Connecting and Configuring your Modem Router
D.
Plug your Router’s power
supply into the black port
labeled “Power” on the back
of your Router.
E.
Wait 20 seconds for the Router to
start up. Look at the display on
the front of the Router. Make sure
the “Wired” and “Modem-Router”
icons are lit up in blue. If they are
not, recheck your connections.
1.2 Replacing an Existing Modem or Modem Router
Follow these steps if you currently have a modem or a modem
router that you will be replacing with your new Router.
computer
modem router
A.
Unpack your new Router from
the box and place it next to
your computer. Raise the
Router’s antennas.
20
Connecting and Configuring your Modem Router
B.
D.
E.
Locate the cable that connects
your old modem to the ADSL
wall jack. Unplug it from your old
modem and then connect it to the
gray port labeled “to ADSL” on
the back of your Router.
Plug your Router’s power
supply into the black port
labeled “Power” on the back
of your Router.
Wait 20 seconds for the Router to
start up. Look at the display on
the front of the Router. Make sure
the “Wired” and “Modem-Router”
icons are lit in blue. If they are
not, recheck your connections.
21
1
2
3
4
5
6
7
8
9
10
section
C.
Locate the cable that connects
your old modem to your
computer. Unplug that cable from
your old modem, and plug it into
any yellow port labeled “to Wired
Computers” on the back of your
new Router.
Connecting and Configuring your Modem Router
Step 2
Set Up the Router – Run the Setup Assistant Software
A.
Shut down any programs that
are running on your computer
at this time.
Turn off any firewall or
Internet-connection-sharing
software on your computer.
B.
Insert the CD into your
computer. The Setup Assistant
will automatically appear on
your computer’s screen within
15 seconds. Click on “Setup
Assistant” to run the Setup
Assistant. Follow the
instructions there.
IMPORTANT: Run the Setup Assistant from the computer that is
directly connected to the Router from Step 1.1B.
Note for Windows Users: If the
Setup Assistant does not start
up automatically, select your
CD-ROM drive from “My
Computer” and double-click on
the file named “SetupAssistant”
to start the Setup Assistant.
22
Connecting and Configuring your Modem Router
Select Country
Select your country from the
drop-down box. Click “Begin”
to continue.
1
2
3
Confirmation Screen
Verify that you have completed all QIG
steps by checking the box to the right
of the arrow. Click “Next” to continue.
5
6
7
Progress Screen
Setup Assistant will show you a
progress screen each time a step in
the setup has been completed.
8
9
10
23
section
4
Connecting and Configuring your Modem Router
2.1 Checking Settings
The Setup Assistant will now
examine your computer’s network
settings and gather information
needed to complete the Router’s
connection to the Internet.
2.2 Verifying Hardware Connections
The Setup Assistant will now
verify your hardware connection.
2.3 Naming your Wireless Network
The Setup Assistant will display
the default wireless network name
or Service Set Identifier (SSID).
This is the name of your wireless
network to which your computers
or devices with wireless network
adapters will connect. You can
either use the default or change it
to something unique. Write down
this name for future reference.
If the Router is capable of “High
Speed Mode”, this option will be
checked. You can turn off this
option later using the Bandwidth
Switch described in this User
Manual (see page 48). Click
“Next” to continue.
24
Connecting and Configuring your Modem Router
2.4 Requesting Internet Account
Info (if needed)
Select your ISP from the
drop-down boxes.
1
2
3
If your Internet account requires
a login and password, you will be
prompted with a screen similar to
the illustration below. Click “Next”
to continue.
5
6
7
2.5 Configuring the Router
The Setup Assistant will now
configure your Router by
sending data to the Router and
restarting it. Wait for the
on-screen instructions.
Note: Do not disconnect any cable
or power off the Router while the
Router is rebooting. Doing so will
render your Router inoperable.
2.6 Checking Internet Connection
We are almost done. The Setup
Assistant will now check your
connection to the Internet.
25
8
9
10
section
4
Connecting and Configuring your Modem Router
Congratulations
You have finished installing your
new Belkin Router. You will see the
Congratulations screen when your
Router can connect to the Internet.
You can begin surfing by opening your
browser and going to any website.
You can use the Setup Assistant to
set up your other wired and wireless
computers to connect to the Internet
by clicking “Next”. If you decide to add
computers to your Router later, select
“Finish—return to Main Menu” and then
click “Next”.
Troubleshooting
If the Setup Assistant is not able to
connect to the Internet, you will
see this screen. Follow the on-screen
instructions to go through the
troubleshooting steps.
2.7 Optional: Assistance Connecting
Other Computers
This optional step will help
you to connect additional
wired and wireless computers
to your network. Follow the
on-screen instructions.
Once you have verified that your other
wired and wireless computers are
properly connected, your network is set
up and working. You can now surf the
Internet. Click “Next” to return to the
main menu.
26
Connecting and Configuring your Modem Router
Step 3
Set Up Wireless Security – Run the Security
Assistant Software
IMPORTANT: Run the Setup Assistant from the computer that is
directly connected to the Router from Steps 1.1B and 1.12B.
2
3
4
5
6
7
8
9
10
Progress Screen
The Security Assistant will show you a
progress screen each time a step has
been completed.
27
section
Now that your network is set up and working, it is recommended
that you turn on wireless security to prevent unauthorized access
to your network from neighboring wireless-enabled computers. The
Security Assistant will guide you through the process. Click “Security
Assistant” and follow the on-screen instructions.
1
Connecting and Configuring your Modem Router
3.1 Picking the Security Type
Select the security type for your
wireless network and click “Next”
to continue.
3.2 Creating a Network Key
Enter a network key (PSK) for
your wireless network and click
“Next” to continue.
3.3 Transferring the Key
After setting up your wireless
security, you will have to transfer
the network key to each of your
wireless computers. Click on
“Transfer Key” if you have a
USB flash drive. Follow the
on-screen instructions, or click
on “Print” to print the information.
Manually enter it to each wireless
computer. Then, click “Next”
to continue.
28
Connecting and Configuring your Modem Router
3.4 Verifying the Connection
Congratulations
Once you have verified that your
wireless computers are properly
connected, your wireless network is
set up and secured. You now can run
your network wirelessly and securely.
Click “Finish” to take you back to the
main menu.
2
3
4
5
6
7
8
9
10
29
section
If all your wireless computers are
able to connect to the Router,
click “Next”. If you are having
trouble, select “I had problem
with at least one computer”
and click “Next”. Then, follow
on-screen instructions.
1
Alternate Setup Method
Step 1
Hardware Connections – Follow the
Quick Installation Guide (QIG)
See the QIG or Step 1: Hardware Connections from the
previous section.
Step 2
Set your Computer’s Network Settings to Work
with a DHCP Server
See the section in this User Manual called “Manually Configuring
Network Settings” for directions.
Step 3
Configuring the Router Using the Web-Based Advanced
User Interface
Using your Internet browser, you can access the Router’s Web-Based
Advanced User Interface. In your browser, type “192.168.2.1” (do
not type in anything else such as “http://” or “www”). Then press
the “Enter” key.
30
Alternate Setup Method
1
Logging into the Router
You will see the Router’s home page in your browser window. The
home page is visible to any user who wants to see it. To make any
changes to the Router’s settings, you have to log in. Clicking the
“Login” button or clicking on any one of the links on the home page
will take you to the login screen. The Router ships with no password
entered. In the login screen, leave the password blank and click the
“Submit” button to log in.
2
3
4
6
7
8
Logging out of the Router
One computer at a time can log into the Router for the purposes
of making changes to the settings of the Router. Once a user
has logged in to make changes, there are two ways that the computer
can be logged out. Clicking the “Logout” button will log the computer
out. The second method is automatic. The login will time out after a
specified period of time. The default login time-out is 10 minutes.
This can be changed from one to 99 minutes. For more information,
see the section in this manual titled “Changing the Login
Time-Out Setting”.
Understanding the Web-Based Advanced User Interface
The home page (shown on the next page) is the first page you will
see when you access the Advanced User Interface (UI). The home
page shows you a quick view of the Router’s status and settings. All
advanced setup pages can be reached from this page.
31
9
10
section
5
Alternate Setup Method
(13)
(6)
(2) (3) (4)
(5)
(8)
(7)
(9)
(1)
(10)
(11)
(12)
1.
2.
Quick-Navigation Links
You can go directly to any of the Router’s advanced UI pages by
clicking directly on these links. The links are divided into logical
categories and grouped by tabs to make finding a particular setting
easier to find. Clicking on the purple header of each tab will show you a
short description of the tab’s function.
Home Button
The home button is available in every page of the UI. Pressing this
button will take you back to the home page.
3.
Help Button
4.
Login/Logout Button
The “Help” button gives you access to the Router’s help pages. Help
is also available on many pages by clicking “more info” next to certain
sections of each page.
This button enables you to log in and out of the Router with the press
of one button. When you are logged into the Router, this button will
change to read “Logout”. Logging into the Router will take you to a
separate login page where you will need to enter a password. When you
are logged into the Router, you can make changes to the settings. When
you are finished making changes, you can log out of the Router by
clicking the “Logout” button. For more information about logging into the
Router, see the section called “Logging into the Router”.
32
Alternate Setup Method
5.
1
Internet-Status Indicator
This indicator is visible in all pages of the Router, indicating the connection
status of the Router. When the indicator says “Connected” in blue, the
Router is connected to the Internet. When the Router is not connected to
the Internet, the indicator will read “No Connection” in RED. The indicator
is automatically updated when you make changes to the settings of the
Router.
Connect/Disconnect Buttons
7.
Language
Use these buttons to manually connect or disconnect your ADSL
connection as needed.
Shows the active language for the Advanced User Interface. Select a
desirable language by clicking one of the available languages.
3
4
5
6
8.
Version Info
Shows the firmware version, boot-code version, hardware version, and
serial number of the Router.
7
9.
LAN Settings
8
Shows you the settings of the Local Area Network (LAN) side of the Router.
Changes can be made to the settings by clicking on any one of the links
(IP Address, Subnet Mask, DHCP Server) or by clicking the “LAN” quicknavigation link on the left side of the screen.
10. Internet Settings
Shows the settings of the Internet/WAN side of the Router that connects to
the Internet. Changes to any of these settings can be made by clicking on
the links or by clicking on the “Internet/WAN” quick-navigation link on the
left side of the screen.
11. Features
Shows the status of the Router’s NAT, firewall, and wireless features.
Changes can be made to the settings by clicking on any one of the links or
by clicking the quick-navigation links on the left side of the screen.
12. ADSL Info
Shows the ADSL status and transmission rates.
13. Page Name
The page you are on can be identified by this name. This User Manual will
sometimes refer to pages by name. For instance “LAN > LAN Settings”
refers to the “LAN Settings” page.
33
9
10
section
6.
2
Alternate Setup Method
Step 4
Configuring your Router for Connection to your Internet
Service Provider (ISP)
The “Internet/WAN” tab is where you will set up your Router to
connect to your Internet Service Provider (ISP). The Router is capable
of connecting to virtually any ISP’s system provided you have
correctly configured the Router’s settings for your ISP’s connection
type. Your ISP connection settings are provided to you by your ISP.
To configure the Router with the settings that your ISP gave you,
click “Connection Type” (A) on the left side of the screen. Select
the connection type you use. If your ISP gave you DNS settings,
clicking “DNS” (B) allows you to enter DNS address entries for ISPs
that require specific settings. Clicking “MAC Address” (C) will let you
clone your computer’s MAC address or type in a specific WAN MAC
address, if required by your ISP. When you have finished making
settings, the “Internet Status” indicator will read “connection OK” if
your Router is set up properly.
(A)
(B)
(C)
34
Alternate Setup Method
1
Connection Type
From the “Connection Type” page, you can select one of these five
connection types based on the instruction provided by your ISP:
•
PPPoE
•
PPPoA
•
Dynamic/Fixed IP (1483 Bridged)
•
Static IP (IPoA)
•
Modem Only (Disable Internet Sharing)
2
3
5
6
7
(1)
8
9
10
35
section
Select the type of connection you use by clicking the radio button (1)
next to your connection type and then clicking “Next” (2).
4
Alternate Setup Method
Setting your ISP Connection Type to PPPoE or PPPoA
PPPoE (Point-to-Point Protocol over Ethernet) is the standard method
of connecting networked devices. It requires a user name and password
to access the network of your ISP for connecting to the Internet.
PPPoA (PPP over ATM) is similar to PPPoE, but is mostly implemented
in the UK. Select PPPoE or PPPoA and click “Next”. Then enter the
information provided by your ISP, and click “Apply Changes” to activate
your settings.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
1.
User Name - Enter the user name. (Assigned by your ISP).
2.
Password - Enter your password. (Assigned by your ISP).
3.
Retype Password - Confirm the password. (Assigned
4.
VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit
by your ISP).
Identifier (VCI) parameter here. (Assigned by your ISP).
5.
Encapsulation - Select your encapsulation type (supplied by
your ISP) to specify how to handle multiple protocols at the ATM
transport layer.
VC-MUX: PPPoA Virtual Circuit Multiplexer (null encapsulation)
allows only one protocol running per virtual circuit with
fewer overheads.
LLC: PPPoA Logical Link Control allows multiple protocols running
over one virtual circuit (more overhead).
36
Alternate Setup Method
6.
MTU - Enter the MTU value for your ISP.
7.
Disconnect after of x minutes of no activity - Checking the box and
enter the number of minute that you want the modem router to auto
disconnect after no activity. After this time has been exceeded, the
connection will be terminated.
Setting your Connection Type to Dynamic/Fixed IP (1483 Bridged)
This connection method bridges your network and ISP’s network
together. The Router can obtain an IP address automatically from your
ISP’s DHCP server or accept a fixed IP address assigned by your ISP.
2
3
4
5
6
7
8
(1)
(2)
For Dynamic IP connection:
1.
VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit
Identifier (VCI) parameter here. These identifiers are assigned by
your ISP.
2.
Encapsulation - Select LLC or VC MUX your ISP uses.
Click “Apply Changes” to save and activate your settings. To go
back to the original settings before saving, click “Clear Changes”;
or click any of the Quick-Navigation links for other options. Your
new settings will not be saved unless you click “Apply Changes”.
37
9
10
section
Click “Apply Changes” to save and activate your settings.
To go back to the original settings before saving, click “Clear
Changes”. Or click any of the Quick-Navigation links for other
options. Your new settings will not be saved unless your click
“Apply Changes”.
1
Alternate Setup Method
(1)
(2)
(3)
(4)
(5)
(6)
For Dynamic IP connection:
1.
IP assigned by ISP - Select “No” if your ISP instructed you to use
fixed IP.
2.
IP Address - Enter an IP address assigned by your ISP for the
Router WAN interface.
3.
Subnet Mask - Enter a subnet mask assigned by your ISP.
4.
Default Gateway - Enter a default gateway IP address assigned
by your ISP.
5.
VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit
Identifier (VCI) parameters here. These identifiers are assigned by
your ISP.
6.
Encapsulation - Select the LLC or VC MUX your ISP uses.
Click “Apply Changes” to save and activate your settings. To go
back to the original settings before saving, click “Clear Changes”.
Or click any of the Quick-Navigation links for other options. Your
new settings will not be saved unless your click “Apply Changes”.
38
Alternate Setup Method
Setting your ISP Connection Type to Static IP (IPoA)
This connection type is also called “Classical IP over ATM” or
“CLIP”, which your ISP provides a fixed IP for your Router to connect
to the Internet.
1
2
3
4
5
6
7
8
1.
WAN IP Address - Enter an IP address assigned by your ISP for
the Router WAN interface.
2.
Subnet Mask - Enter a subnet mask assigned by your ISP.
3.
Use Static Default Gateway - Enter a default gateway IP address.
If the Router cannot find the destination address within its
local network, it will forward the packets to the default gateway
assigned by your ISP.
4.
VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit
Identifier (VCI) parameter here. These identifiers are assigned by
your ISP.
5.
Encapsulation - Select LLC or VC MUX your ISP uses.
Click “Apply Changes” to save and activate your settings. To go
back to the original settings before saving, click “Clear Changes”.
Or click any of the Quick-Navigation links for other options. Your
new settings will not be saved unless your click “Apply Changes”.
39
9
10
section
(1)
(2)
(3)
(4)
(5)
Alternate Setup Method
Setting your Connection Type to Modem Only (Disable
Internet Sharing)
In this mode, the Router simply acts as a bridge passing packets
across the DSL port. It requires additional software to be installed on
your computers in order to access the Internet.
(2)
(3)
1.
Enable Bridge Service - Check this box to enable bridge service
2.
VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit
Identifier (VCI) parameters here. (Assigned by your ISP).
3.
Encapsulation - Select the LLC or VC MUX your ISP uses.
Click “Apply Changes” to save and activate your settings. To go
back to the original settings before saving, click “Clear Changes”.
Or click any of the Quick-Navigation links for other options. Your
new settings will not be saved unless your click “Apply Changes”.
40
Alternate Setup Method
Setting Custom Domain Name Server (DNS) Settings
2
3
4
5
6
7
(1)
(2)
8
9
10
41
section
A “Domain Name Server” is a server located on the Internet that
translates Universal Resource Locaters (URLs) like “www.belkin.
com” to IP addresses. Many Internet Service Providers (ISPs) do not
require you to enter this information into the Router. The “Automatic
from ISP” box (1) should be checked if your ISP did not give you a
specific DNS address. If you are using a static IP connection type,
then you may need to enter a specific DNS address and secondary
DNS address for your connection to work properly. If your connection
type is dynamic or PPPoE, it is likely that you do not have to enter a
DNS address. Leave the “Automatic from ISP” box checked. To enter
the DNS address settings, uncheck the “Automatic from ISP” box and
enter your DNS entries in the spaces provided. Click “Apply Changes”
(2) to save the settings.
1
Using the Web-Based Advanced User Interface
Using the Web-Based Advanced User Interface
Using your Internet browser, you can access the Router’s Web-Based
Advanced User Interface. In your browser, type “192.168.2.1” (do not
type in anything else such as “http://” or “www”) then press the
“Enter” key.
You will see the Router’s home page in your browser window.
Viewing the LAN Settings
Clicking on the header of the LAN tab (1) will take you to the LAN tab’s
header page. A quick description of the functions can be found here. To
view the settings or make changes to any of the LAN settings, click on
“LAN Settings” (2) or to view the list of connected computers, click on
“DHCP client list” (3).
(1)
(2)
(3)
42
Using the Web-Based Advanced User Interface
1
Changing LAN Settings
All settings for the internal LAN setup of the Router can be viewed
and changed here.
2
3
(1)
(2)
(3)
(4)
5
6
7
1.
8
IP Address
The “IP address” is the internal IP address of the Router. The
default IP address is “192.168.2.1”. To access the advanced setup
interface, type this IP address into the address bar of your browser.
This address can be changed if needed. To change the IP address,
type in the new IP address and click “Apply Changes”. The IP
address you choose should be a non-routable IP. Examples of a
non-routable IP are:
192.168.x.x (where x is anything between 0 and 255)
10.x.x.x (where x is anything between 0 and 255)
2.
Subnet Mask
There is no need to change the subnet mask. This is a unique,
advanced feature of your Belkin Router. It is possible to change
the subnet mask if necessary; however, do NOT make changes to
the subnet mask unless you have a specific reason to do so. The
default setting is “255.255.255.0”.
43
9
10
section
(5)
(6)
4
Using the Web-Based Advanced User Interface
3.
DHCP Server
The DHCP server function makes setting up a network very easy
by assigning IP addresses to each computer on the network
automatically. The default setting is “On”. The DHCP server
can be turned OFF if necessary; however, in order to do so you
must manually set a static IP address for each computer on your
network. To turn off the DHCP server, select “Off” and click “Apply
Changes”.
4.
IP Pool
The range of IP addresses set aside for dynamic assignment
to the computers on your network. The default is 2–100 (99
computers). If you want to change this number, you can do so
by entering a new starting and ending IP address and clicking on
“Apply Changes”. The DHCP server can assign 100 IP addresses
automatically. This means that you cannot specify an IP address
pool larger than 100 computers. For example, starting at 50
means you have to end at 150 or lower so as not to exceed the
100-client limit. The starting IP address must be lower in number
than the ending IP address.
5.
Lease Time
The length of time the DHCP server will reserve the IP address
for each computer. We recommend that you leave the lease
time set to “Forever”. The default setting is “Forever”, meaning
that any time a computer is assigned an IP address by the
DHCP server, the IP address will not change for that particular
computer. Setting lease times for shorter intervals such as one
day or one hour frees IP addresses after the specified period of
time. This also means that a particular computer’s IP address
may change over time. If you have set any of the other advanced
features of the Router such as DMZ or client IP filters, these are
dependent on the IP address. For this reason, you will not want
the IP address to change.
6.
Local Domain Name
The default setting is “Belkin”. You can set a local domain name
(network name) for your network. There is no need to change
this setting unless you have a specific advanced need to do so.
You can name the network anything you want such as
“MY NETWORK”.
44
Using the Web-Based Advanced User Interface
1
Viewing the DHCP Client List Page
You can view a list of the computers (known as clients), which are
connected to your network. You are able to view the IP address (1) of
the computer, the host name (2) (if the computer has been assigned
one), and the MAC address (3) of the computer’s network interface
card (NIC). Pressing the “Refresh” (4) button will update the list. If
there have been any changes, the list will be updated.
(1)
(2)
(3)
2
3
4
5
6
7
8
9
Configuring the Wireless Network Settings
The “Wireless” tab lets you make changes to the wireless network
settings. From this tab you can make changes to the wireless network
name or Service Set Identifier (SSID), operating channel, encryption
security settings, and configure the Router to be used as an
access point.
45
10
section
(4)
Using the Web-Based Advanced User Interface
Changing the Wireless Network Name (SSID)
To identify your wireless network, a name called the SSID is used.
The SSID is your network name. The default network name of the
Router is “Belkin N1 Wireless” followed by six digits that are unique
to your Router. Your network name will look something like
“Belkin_N1_Wireless_123456”. You can change this to anything you
choose, or you can leave it unchanged. Keep in mind, if you decide
to change your wireless network name, and there are other wireless
networks operating in your area, your network name needs to be
different from other wireless networks that may be operating in your
area. To change the SSID, type in the SSID that you want to use
in the SSID field (1) and click “Apply Changes” (2). The change is
immediate. If you make a change to the SSID, your wireless-equipped
computers may also need to be reconfigured to connect to your new
network name. Refer to the documentation of your wireless network
adapter for information on making this change.
(1)
(2)
Note: Please periodically check for new Router firmware updates
from the “Utilities > Firmware update” page. Newer firmware can fix
problems, add wireless features, and/or improve wireless performance
(see page 69).
46
Using the Web-Based Advanced User Interface
1
Changing the Wireless Channel
There are a number of operating channels from which you can choose—
in the United Kingdom (and most of Europe) and Australia, there are 13.
In other countries, there are other channel requirements. Your Router is
configured to operate on the proper channels for the country in which
you reside. The channel can be changed if needed. If there are other
wireless networks operating in your area, your network should be set to
operate on a channel that is different than the other wireless networks.
Extension Channel
Using the Wireless Mode Switch
This switch allows you to set the Router’s wireless modes. There are
several modes.
Note: Some modes may require firmware updates to be enabled.
1) Off
This mode will turn OFF the Router’s access point, so no wireless
devices can join the network. Turning off the wireless function of
your Router is a great way to secure your network when you are
away from home for a long period of time, or don’t want to use the
wireless feature of the Router at a certain time.
2) 802.11g
Setting the Router to this mode will allow only 802.11g- and
802.11b-compliant devices to join the network. N1/draft 802.11n
devices will operate at the 802.11g speed only.
3) 802.11b & 802.11g & 802.11n
Setting the Router to this mode will allow N1/draft 802.11n-,
802.11g-, and 802.11b-compliant devices to join the network.
4) 802.11n
Setting the Router to this mode will allow only N1/draft
802.11n-compliant devices to join the network, keeping out
802.11g and 802.11b devices.
47
3
4
5
6
7
8
9
10
section
The IEEE 802.11n draft specification allows the use of a secondary
channel to double the bandwidth (see the “Using the Bandwidth Switch”
section on the next page). An appropriate extension channel will be
displayed when operating in 40MHz mode (see the “Using the Wireless
Mode Switch” section below). The channel can be changed if necessary.
2
Using the Web-Based Advanced User Interface
Using the Bandwidth Switch
This switch allows you to set the Router’s wireless bandwidth modes.
There are several modes available:
1) 20MHz/40MHz
Setting the Router to this mode allows it to switch automatically
between 20MHz and 40MHz operation. This mode enables 40MHz
operation, to maximize speed for N1 draft 802.11n-compliant
devices when conditions permit. When a legacy 802.11g access
point is presented and occupies an adjacent secondary channel,
the Router automatically reverts to 20MHz operation to maximize
compatibility. Set the Router to this mode for higher performance.
2) 20MHz
Setting the Router to this mode allows only 20MHz operation.
This mode is compatible with N1, draft 802.11n-, 802.11g-, and
802.11b-compliant devices, but will limit N1, draft 802.11ncompliant devices’ bandwidth by half. Reducing bandwidth to
20MHz-only operation might solve some wireless problems. This is
the default mode for the Router.
Using the Broadcast SSID Feature
Note: This advanced feature should be employed by advanced users
only. For security, you can choose not to broadcast your network’s
SSID. Doing so will keep your network name hidden from computers
that are scanning for the presence of wireless networks. To turn off
the broadcast of the SSID, remove the check mark from the box next
to “Broadcast SSID”, and then click “Apply Changes”. The change is
immediate. Each computer now needs to be set to connect to your
specific SSID; an SSID of “ANY” will no longer be accepted. Refer to
the documentation of your wireless network adapter for information on
making this change.
Protected Mode Switch
Protected mode ensures proper operation of N1, draft 802.11n-compliant
devices on your wireless network when 802.11g or 802.11b devices
are present or when there is heavy 802.11g or 802.11b traffic in the
operating environment. Use protected mode if your network consists of
a mix of Belkin N1 Wireless Cards and 802.11g or 802.11b cards on your
network. If you are in an environment that includes little to no 802.11g
or 802.11b wireless network traffic, you will achieve the best N1 wireless
performance with protected mode OFF. Conversely, in an environment
with HEAVY 802.11g or 802.11b traffic or interference, you will achieve
the best N1 wireless performance with protected mode ON. This will
ensure N1 wireless performance is not affected.
48
Using the Web-Based Advanced User Interface
802.11e/WMM (Wi-Fi ® Multimedia) QoS
WMM, based on 802.11e QoS (Quality of Service), prioritizes important
data on your network, such as multimedia content and voice-over-IP
(VoIP), so it will not be interfered with by other data being sent over
the network. This feature requires other wireless devices, such as Wi-Fi
phones or wireless laptops, to support WMM for best results.
Changing the Wireless Security Settings
The Router features WPA2, which is the second generation of the
WPA-based 802.11i standard. It offers a higher level of wireless
security by combining advanced network authentication and stronger
Advanced Encryption Standard (AES) encryption methods.
2
3
4
5
6
7
8
WPA2 Requirements
IMPORTANT: In order to use WPA2 security, all your computers and
wireless client adapters must be upgraded with patches, driver,
and client utility software that supported WPA2. At the time of this
User Manual’s publication, a couple security patches are available,
for free download, from Microsoft ®. These patches work only with
the Windows XP operating system. Other operating systems are not
supported at this time.
For Windows XP computers that do not have Service Pack 2
(SP2), a file from Microsoft called “Windows XP Support Patch
for Wireless Protected Access (KB 826942)” is available for free
download at http://support.microsoft.com/kb/826942
For Windows XP with Service Pack 2, Microsoft has released
a free download to update the wireless client components to
support WPA2 (KB971021). The update is available from:
http://support.microsoft.com/kb/917021
IMPORTANT: You also need to ensure that all your wireless client
cards/adapters support WPA2, and that you have downloaded and
installed the latest driver. Most of the Belkin wireless cards have
driver updates available for download from the Belkin support site:
www.belkin.com/networking.
49
9
10
section
Your Router is equipped with the latest security standard called
Wi-Fi Protected Access 2 (WPA2). It also supports the legacy security
standard called Wired Equivalent Privacy (WEP). By default, wireless
security is disabled. To enable security, you will need to determine
which standard you want to use. To access the security settings, click
“Security” on the “Wireless” tab.
1
Using the Web-Based Advanced User Interface
Setting WPA/WPA2-Personal (PSK)
Like WPA security, WPA2 is available in both WPA2-Personal (PSK)
mode and WPA2-Enterprise (RADIUS) mode. Typically, WPA2Personal (PSK) is the mode that will be used in a home environment,
while WPA2-Enterprise (RADIUS) is implemented in a business
environment where an external radius server distributes the network
key to the clients automatically. This guide will focus on WPA2Personal (PSK) usage. Please refer to the User Manual for more
information about wireless security and different types of wireless
security.
1.
After you’ve set up your Router, go to the “Security” page under
“Wireless” and select “WPA/WPA2-Personal (PSK)” from the
“Security Mode” drop-down menu.
2.
For “Authentication”, select “WPA-PSK”, “WPA2-PSK”, or
“WPA-PSK + WPA2-PSK”. This setting will have to be identical
on the wireless clients that you set up. “WPA-PSK + WPA2-PSK”
mode will allow the Router to support clients running either WPA
or WPA2 security.
3.
“Encryption Technique”, select “TKIP”, “AES”, or “TKIP+AES”.
This setting will have to be identical on the wireless clients that
you set up.
4.
Enter your pre-shared key (PSK). This can be from eight to 63
characters and can be letters, numbers, or symbols. This same
key must be used on all of the wireless clients that you set up.
For example, your PSK might be something like: “Smith family
network key”. Click “Apply Changes” to finish. You must now set
all wireless clients to match these settings.
50
Using the Web-Based Advanced User Interface
1
2
3
4
5
IMPORTANT: Make sure your wireless computers are updated to work
7
with WPA2 and have the correct settings to get proper connection to
the Router.
8
Setting WPA Security
9
Note: To use WPA security, your wireless network cards must be
equipped with software that supports WPA. At the time this User Manual
was published, a security patch from Microsoft is available for free
download. This patch works only with Windows XP.
Your Router supports WPA-PSK (no server). WPA-PSK uses what is
known as a pre-shared key as the security key. A pre-shared key is
basically a password that is between eight and 39 characters long. It
can be a combination of letters, numbers, or characters. Each client
uses the same key to access the network. Typically this is the mode
that will be used in a home environment.
51
10
section
6
Using the Web-Based Advanced User Interface
Setting WPA-PSK
1.
From the “Security Mode” drop-down menu, select “WPA-PSK
(no server)”.
2.
For “Encryption Technique”, select “TKIP” or “AES”. This setting
will have to be identical on the clients that you set up.
3.
Enter your pre-shared key. This can be from eight to 39
characters and can be letters, numbers, or symbols. This same
key must be used on all of the clients that you set up.
4.
Click “Apply Changes” to finish. You must now set all clients to
match these settings.
52
Using the Web-Based Advanced User Interface
1
Setting WEP Encryption
Note to Mac users: The “Passphrase” option will not operate with
Apple® AirPort®. To configure encryption for your Mac computer, set the
encryption using the manual method described in the next section.
Select “128-bit WEP” or “64-bit WEP” from the drop-down menu.
2.
After selecting your WEP encryption mode, you can enter your
WEP key manually by typing in the hex values in the space
provided, or you can type a passphrase in the “PassPhrase” field
and click “Generate” to create a WEP key from the passphrase.
Click “Apply Changes” to finish. You must now set all of your
clients to match these settings.
3
4
5
6
7
8
9
10
3.
Encryption in the Router is now set. Each of your computers on
your wireless network will now need to be configured with the
same passphrase. Refer to the documentation of your wireless
network adapter for information on making this change.
53
section
1.
2
Using the Web-Based Advanced User Interface
Using a Hexadecimal Key
A hexadecimal key is a mixture of numbers and letters from A–F
and 0–9. 64-bit keys are 10 digits long and can be divided into five
two-digit numbers. 128-bit keys are 26 digits long and can be divided
into 13 two-digit numbers.
For instance:
AF 0F 4B C3 D4 = 64-bit key
C3 03 0F AF 0F 4B B2 C3 D4 4B C3 D4 E7 = 128-bit key
In the boxes below, make up your key by writing in two characters
between A–F and 0–9. You will use this key to program the encryption
settings on your Router and your wireless computers.
Note to Mac users: Original Apple AirPort products support 64bit encryption only. Apple AirPort 2 products can support 64-bit or
128-bit encryption. Please check your product to see which version
you are using. If you cannot configure your network with 128-bit
encryption, try 64-bit encryption.
54
Using the Web-Based Advanced User Interface
1
Using the Access Point Mode
Note: This advanced feature should be employed by advanced users
only. The Router can be configured to work as a wireless network
access point. Using this mode will defeat the NAT IP sharing feature
and DHCP server. In Access Point (AP) mode, the Router will need
to be configured with an IP address that is in the same subnet as
the rest of the network that you will bridge to. The default IP address
is 192.168.2.254 and subnet mask is 255.255.255.0. These can be
customized for your need.
Enable the AP mode my selecting “Enable” (1) in the “Use as
Access Point only” page. When you select this option, you will be
able to change the IP settings.
2.
Set your IP settings to match your network. Click
“Apply Changes” (2).
3.
Connect a cable from the “Modem” port on the Router to your
existing network.
The Router is now acting as an access point. To access the Router’s
Web-Based Advanced User Interface again, type the IP address
you specified into your browser’s navigation bar. You can set the
encryption settings, MAC address filtering, SSID, and
channel normally.
(1)
(2)
55
3
4
5
6
7
8
9
10
section
1.
2
Using the Web-Based Advanced User Interface
Setting MAC Address Control
The MAC address filter is a powerful security feature that allows you
to specify which computers are allowed on the wireless network.
Note: This list applies only to wireless computers. This list can be
configured so any computer attempting to access the wireless network
that is not specified in the filter list will be denied access. When you
enable this feature, you must enter the MAC address of each client
(computer) to which you want to allow network access. The “Block”
feature lets you turn on and off access to the network easily for any
computer without having to add and remove the computer’s MAC
address from the list.
(1)
(2)
(3)
(4)
Setting up an Allow Access List
1. Select the “Allow” radio button (1) to begin setting up a list of
computers allowed to connect to the wireless network.
2.
Next, in the “MAC Address” field that is blank (2), type in the
MAC address of the wireless computer you want to be able to
access the wireless network, then click “<<Add” (3).
3.
Continue to do this until all of the computers you want to add
have been entered.
4.
Click “Apply Changes” (4) to finish.
56
Using the Web-Based Advanced User Interface
1
(1)
2
(2)
(3)
(4)
3
4
5
7
Setting up a Deny Access List
The “Deny Access” list lets you specify computers that you DO
NOT want to access the network. Any computer in the list will not
be allowed access to the wireless network. All others will.
1.
Select the “Deny” radio button (1) to begin setting up a list of
computers to be denied access to the wireless network.
2.
Next, in the “MAC Address” field that is blank (2), type in the
MAC address of the wireless computer you want to deny access
to the wireless network, then click “<<Add” (3).
3.
Continue to do this until all of the computers you want to deny
access to have been entered.
4.
Click “Apply Changes” (4) to finish.
57
8
9
10
section
6
Using the Web-Based Advanced User Interface
Configuring the Firewall
Your Router is equipped with a firewall that will protect your network
from a wide array of common hacker attacks including:
•
IP Spoofing
•
Land Attack Ping of Death (PoD)
•
Denial of Service (DoS)
•
IP with zero length
•
Smurf Attack
•
TCP Null Scan
•
SYN flood
•
UDP flooding
•
Tear Drop Attack
•
ICMP defect
•
RIP defect
•
Fragment flooding
The firewall also masks common ports that are frequently used to
attack networks. These ports appear to be “stealth” meaning that
for all intents and purposes, they do not exist to a would-be hacker.
Disabling the firewall protection will not leave your network completely
vulnerable to hacker attacks, but it is recommended that you leave the
firewall enabled.
58
Using the Web-Based Advanced User Interface
Configuring Internal Forwarding Settings
The Virtual Servers function will allow you to route external (Internet)
calls for services such as a web server (port 80), FTP server (Port 21),
or other applications through your Router to your internal network.
Since your internal computers are protected by a firewall, computers
outside your network (over the Internet) cannot get to them because
they cannot be “seen”. A list of common applications has been
provided in case you need to configure the Virtual Server function
for a specific application. If your application is not listed, you will
need to contact the application vendor to find out which port settings
you need.
1
2
3
4
5
7
8
9
10
Choosing an Application
Select your application from the drop-down list. Click “Add”. The
settings will be transferred to the next available space in the screen.
Click “Apply Changes” to save the setting for that application. To
remove an application, select the number of the row that you want to
remove then click “Clear”.
Manually Entering Settings into the Virtual Server
To manually enter settings, enter the IP address in the space provided
for the internal (server) machine, the port(s) required to pass (use a
comma between multiple ports), select the port type (TCP or UDP),
and click “Apply Changes”. You can only pass one port per internal IP
address. Opening ports in your firewall can pose a security risk. You
can enable and disable settings very quickly. It is recommended that
you disable the settings when you are not using a specific application.
59
section
6
Using the Web-Based Advanced User Interface
Setting Client IP Filters
The Router can be configured to restrict access to the Internet,
email, or other network services at specific days and times. Restriction
can be set for a single computer, a range of computers,
or multiple computers.
To restrict Internet access to a single computer for example, enter the
IP address of the computer you wish to restrict access to in the IP
fields (1). Next, enter “80” in both the port fields (2). Select “Both” (3).
Select “Block” (4). You can also select “Always” to block access all
of the time. Select the day to start on top (5), the time to start on top
(6), the day to end on the bottom (7), and the time to stop (8) on the
bottom. Select “Enable” (9). Click “Apply Changes”. The computer at
the IP address you specified will now be blocked from Internet access
at the times you specified. Note: Be sure you have selected the
correct time zone under “Utilities> System Settings> Time Zone”.
(1)
(2)
(3)
60
(4)
(5)
(6)
(7)
(8)
(9)
Using the Web-Based Advanced User Interface
Enabling the Demilitarized Zone (DMZ)
The DMZ feature allows you to specify one computer on your network
to be placed outside of the firewall. This may be necessary if the
firewall is causing problems with an application such as a game or
video conferencing application. Use this feature on a temporary basis.
The computer in the DMZ is NOT protected from hacker attacks.
1
2
3
4
5
7
8
9
To put a computer in the DMZ, enter the last digits of its IP address in
the IP field and select “Enable”. Click “Apply Changes” for the change
to take effect. If you are using multiple static WAN IP addresses,
it is possible to select which WAN IP address the DMZ host will be
directed to. Type in the WAN IP address you wish the DMZ host to
direct to, enter the last two digits of the IP address of the DMZ host
computer, select “Enable” and click “Apply Changes”.
61
10
section
6
Using the Web-Based Advanced User Interface
Using Dynamic DNS
The Dynamic DNS service allows you to alias a dynamic IP address
to a static host name in any of the many domains DynDNS.org offers,
allowing your network computers to be more easily accessed from
various locations on the Internet. DynDNS.org provides this service, for
up to five host names, free to the Internet community.
The Dynamic DNS SM service is ideal for a home website, file server, or
to make it easy to access your home PC and stored files while you’re at
work. Using the service can ensure that your host name always points
to your IP address, no matter how often your ISP changes it. When your
IP address changes, your friends and associates can always locate you
by visiting yourname.dyndns.org instead!
To register free for your Dynamic DNS host name, please visit
http://www.dyndns.org.
Setting up the Router’s Dynamic DNS Update Client
You must register with DynDNS.org’s free update service before using
this feature. Once you have your registration, follow the directions below.
1. Select DynDNS.org from the “DNS Service” drop-down box (1).
2. Enter your DynDNS.org user name in the “User Name” field (2).
3. Enter your DynDNS.org password in the “Password” field (3).
4. Enter the DynDNS.org domain name you set up with DynDNS.org
in the “Domain Name” field (4).
5. Click “Update Dynamic DNS” to update your IP address (5).
Whenever your IP address assigned by your ISP changes, the Router will
automatically update DynDNS.org’s servers with your new IP address. You
can also do this manually by clicking the “Update Dynamic DNS” button (5).
(1)
(2)
(3)
(5)
62
(4)
Using the Web-Based Advanced User Interface
1
Blocking an ICMP Ping
Computer hackers use what is known as “pinging” to find potential
victims on the Internet. By pinging a specific IP address and receiving a
response from the IP address, a hacker can determine that something of
interest might be there. The Router can be set up so it will not respond
to an ICMP ping from the outside. This heightens your Router’s security
level.
2
3
4
5
6
7
8
9
To turn off the ping response, select “Block ICMP Ping” (1) and click “Apply
Changes”. The Router will not respond to an ICMP ping.
Utilities
The “Utilities” screen lets you manage different parameters of the Router
and perform certain administrative functions.
63
10
section
(1)
Using the Web-Based Advanced User Interface
Restarting the Router
Sometimes it may be necessary to restart or reboot the Router if it
begins working improperly. Restarting or rebooting the Router will
NOT delete any of your configuration settings.
Restarting the Router to Restore Normal Operation
1.
Click the “Restart
Router” button.
2.
The following message
will appear. Click “OK”.
3.
The following message
will appear. Restarting
the Router can take
up to 60 seconds. It is
important not to turn off
the power to the Router
during the restart.
4.
A 60-second countdown will appear on the screen. When the
countdown reaches zero, the Router will be restarted. The Router
home page should appear automatically. If not, type in the
Router’s address (default = 192.168.2.1) into the navigation
bar of your browser.
64
Using the Web-Based Advanced User Interface
1
Restoring Factory Default Settings
Using this option will restore all of the settings in the Router to the
factory (default) settings. It is recommended that you back up your
settings before you restore all of the defaults.
1.
Click the “Restore
Defaults” button.
2
3
4
5
6
The following message
will appear. Click “OK”.
7
8
3.
4.
The following message
will appear. Restoring
the defaults includes
restarting the Router.
It can take up to 60
seconds. It is important
not to turn the power
to the Router off during
the restart.
9
10
A 60-second countdown will appear on the screen. When the
countdown reaches zero, the Router’s defaults will be restored.
The Router home page should appear automatically. If it does
not, type in the Router’s address (default = 192.168.2.1) into the
navigation bar of your browser.
65
section
2.
Using the Web-Based Advanced User Interface
Saving a Current Configuration
You can save your current configuration by using this feature. Saving
your configuration will allow you to restore it later if your settings are
lost or changed. It is recommended that you back up your current
configuration before performing a firmware update.
1.
Click “Save”. A window
called “File Download”
will open. Click “Save”.
2.
A window will open that
allows you to select
the location where
you want to save the
configuration file. Select
a location. You can
name the file anything
you want, or use the
default name “Config”.
Be sure to name the
file so you can locate
it yourself later. When
you have selected the
location and name of
the file, click “Save”.
66
Using the Web-Based Advanced User Interface
3.
4.
1
When the save is
complete, you will
see this window.
Click “Close”.
2
3
The configuration is
now saved.
4
This option will allow you to restore a previously saved configuration.
5
6
7
8
1.
9
Click “Browse”. A
window will open that
allows you to select
the location of the
configuration file. All
configuration files end
with a “.cfg”. Locate the
configuration file you
want to restore and
double-click on it.
10
67
section
Restoring a Previous Configuration
Using the Web-Based Advanced User Interface
2.
You will be asked if you
want to continue.
Click “OK”.
3.
A reminder window
will appear. It will
take up to 60 seconds
for the configuration
restoration to complete.
Click “OK”.
4.
A 60-second countdown will appear on the screen. When the
countdown reaches zero, the Router’s configuration will be
restored. The Router home page should appear automatically. If
not, type in the Router’s address (default = 192.168.2.1) into the
navigation bar of your browser.
68
Using the Web-Based Advanced User Interface
1
Updating the Firmware
From time to time, Belkin may release new versions of the Router’s
firmware. Firmware updates contain feature improvements and fixes to
problems that may have existed. When Belkin releases new firmware,
you can download the firmware from the Belkin update website and
update your Router’s firmware to the latest version.
2
3
4
5
6
7
8
9
10
Checking for a New Version of Firmware
The “Check Firmware” (1) button allows you to instantly check for a
new version of firmware. When you click the button, a new browser
window will appear informing you that either no new firmware is
available or that there is a new version available. If a new version is
available, you will have the option to download it.
69
section
(1)
Using the Web-Based Advanced User Interface
Downloading a New Version of Firmware
If you click the “Check Firmware” button and a new version of firmware is
available, you will see a screen similar to the one below:
1.
To download the new
version of firmware,
click “Download”.
A window will open that
allows you to select the
location where you want
to save the firmware file.
Select a location. You can
name the file anything you
want, or use the default
name. Be sure to locate the
file in a place where you
can locate it yourself later.
When you have selected
the location, click “Save”.
70
Using the Web-Based Advanced User Interface
2.
1
When the save is
complete, you will see
the following window.
Click “Close”.
2
3
4
3. The download of
the firmware is
complete. To update
the firmware, follow the
next steps in “Updating
the Router’s Firmware”.
5
Updating the Router’s Firmware
7
1.
8
2.
In the “Firmware
Update” page, click
“Browse”. A window will
open that allows you to
select the location of
the firmware update file.
9
10
Browse to the firmware
file you downloaded.
Select the file by
double-clicking on the
file name.
The “Update Firmware”
box will now display
the location and name
of the firmware file
you just selected.
Click “Update”.
71
section
6
Using the Web-Based Advanced User Interface
3.
You will be asked if you
are sure you want to
continue. Click “OK”.
4.
You will see one more message. This message tells you that
the Router may not respond for as long as one minute as the
firmware is loaded into the Router and the Router is rebooted.
Click “OK”.
5.
A 60-second countdown will appear on the screen. When the
countdown reaches zero, the Router firmware update will be
complete. The Router home page should appear automatically. If
not, type in the Router’s address (default = 192.168.2.1) into the
navigation bar of your browser.
72
Using the Web-Based Advanced User Interface
1
Changing System Settings
The “System Settings” page is where you can enter a new
administrator password, set the time zone, enable remote
management, and turn on and off the NAT function of the Router.
Setting or Changing the Administrator Password
3
4
5
6
7
8
9
Changing the Login Time-Out Setting
The login time-out option allows you to set the period of time that you
can be logged into the Router’s advanced setup interface. The timer
starts when there has been no activity. For example, imagine you have
made some changes in the advanced setup interface, then left your
computer alone without clicking “Logout”. Assuming the time-out is
set to 10 minutes, 10 minutes after you leave, the login session will
expire. You will have to log into the Router again to make any more
changes. The login time-out option is for security purposes and the
default is set to 10 minutes.
Note: Only one computer can be logged into the Router’s advanced
setup interface at one time.
73
10
section
The Router ships with NO password entered. If you wish to add a
password for greater security, you can set a password here. Write
down your password and keep it in a safe place, as you will need it if
you need to log into the Router in the future. It is also recommended
that you set a password if you plan to use the remote management
feature of your Router.
2
Using the Web-Based Advanced User Interface
Setting the Time and Time Zone
The Router keeps time by connecting to a Simple Network Time
Protocol (SNTP) server. This allows the Router to synchronize the
system clock to the global Internet. The synchronized clock in the
Router is used to record the security log and control client filtering.
Select the time zone that you reside in. You have the option to select
a primary and a backup NTP server to keep your Router’s clock
synchronized. Select your desired NPT server from the drop-down
box, or simply keep it as is.
If you reside in an area that observes daylight saving, then place a
check mark in the box next to “Enable Daylight Saving”. The system
clock may not update immediately. Allow at least 15 minutes for the
Router to contact the time servers on the Internet and get a response.
You cannot set the clock yourself.
Enabling Remote Management
Before you enable this advanced feature of your Belkin Router, MAKE
SURE YOU HAVE SET THE ADMINISTRATOR PASSWORD. Remote
management allows you to make changes to your Router’s settings
from anywhere on the Internet. There are two methods of remotely
managing the Router. The first is to allow access to the Router from
anywhere on the Internet by selecting “Any IP address can remotely
manage the Router”. By typing in your WAN IP address from any
computer on the Internet, you will be presented with a login screen
where you need to type in the password of your Router.
The second method is to allow a specific IP address only to remotely
manage the Router. This is more secure, but less convenient. To use
this method, enter the IP address you know you will be accessing the
Router from in the space provided and select “Only this IP address
can remotely manage the Router”. Before you enable this function,
it is STRONGLY RECOMMENDED that you set your administrator
password. Leaving the password empty will potentially open your
Router to intrusion.
74
Using the Web-Based Advanced User Interface
Advanced Feature: The “Remote Access Port” option allows you to
configure the desired “Remote Access Port for Remote Management”
feature. The default access port is set to port 80.
1
2
3
4
5
UPnP (Universal Plug-and-Play) is yet another advanced feature
offered by your Belkin Router. It is a technology that offers seamless
operation of voice messaging, video messaging, games, and other
applications that are UPnP-compliant. Some applications require
the Router’s firewall to be configured in a specific way to operate
properly. This usually requires opening TCP and UDP ports, and in
some instances, setting trigger ports. An application that is UPnPcompliant has the ability to communicate with the Router, basically
“telling” the Router which way it needs the firewall configured. The
Router ships with the UPnP feature disabled. If you are using any
applications that are UPnP-compliant, and wish to take advantage of
the UPnP features, you can enable the UPnP feature. Simply select
“Enable” in the “UPnP Enabling” section of the “Utilities” page. Click
“Apply Changes” to save the change.
75
6
7
8
9
10
section
Enabling/Disabling UPnP
Using the Web-Based Advanced User Interface
Enabling/Disabling Auto Firmware Update
This innovation provides the Router with the built-in capability to
automatically check for a new version of firmware and alert you
that the new firmware is available. When you log into the Router’s
advanced interface, the Router will perform a check to see if new
firmware is available. If so, you will be notified. You can choose to
download the new version or ignore it.
76
Manually Configuring Network Settings
Set up the computer that is connected to the cable or DSL modem
FIRST using these steps. You can also use these steps to add
computers to your Router after the Router has been set up to connect
to the Internet.
Manually Configuring Network Settings in Mac OS up to 9.x
1
2
3
1.
Pull down the Apple menu. Select “Control Panels” and
select “TCP/IP”.
4
2.
You will see the TCP/IP control panel. Select “Ethernet Built-In”
or “Ethernet” in the “Connect via:” drop-down menu (1).
5
3.
Next to “Configure”
(2), if “Manually” is
selected, your Router
will need to be set
up for a static IP
connection type. Write
the address information
in the table below.
You will need to enter
this information into
the Router.
6
(1)
8
9
10
4.
If not already set, at “Configure:”, choose “Using DHCP Server”.
This will tell the computer to obtain an IP address from the Router.
5.
Close the window.
If you made any
changes, the following
window will appear.
Click “Save”.
Restart the computer. When the computer restarts, your network
settings are now configured for use with the Router.
77
section
7
(2)
Manually Configuring Network Settings
Manually Configuring Network Settings in Mac OS X
1. Click on the “System Preferences” icon.
2.
Select “Network” (1) from the “System Preferences” menu.
3.
Select “Built-in Ethernet” (2) next to “Show” in the
Network menu.
(1)
(5)
(2)
(3)
(4)
78
Manually Configuring Network Settings
4.
5.
Select the “TCP/IP” tab (3). Next to “Configure” (4), you should
see “Manually” or “Using DHCP”. If you do not, check the
PPPoE tab (5) to make sure that “Connect using PPPoE” is NOT
selected. If it is, you will need to configure your Router for a
PPPoE connection type using your user name and password.
If “Manually” is selected, your Router will need to be set up
for a static IP connection type. Write the address information
in the table below. You will need to enter this information into
the Router.
1
2
3
4
5
6
6.
If not already selected, select “Using DHCP” next to “Configure”
(4), then click “Apply Now”.
Your network settings are now configured for use with the Router.
8
9
10
79
section
7
Manually Configuring Network Settings
Manually Configuring Network Settings in Windows 2000, NT, or XP
1.
Click “Start”, “Settings”, then “Control Panel”.
2.
Double-click on the “Network and dial-up connections” icon
(Windows 2000) or the “Network” icon (Windows XP).
3.
Right-click on the “Local Area Connection” associated with
your network adapter and select “Properties” from the
drop-down menu.
4.
In the “Local Area Connection Properties” window, click “Internet
Protocol (TCP/IP)” and click the “Properties” button. The
following screen will appear:
(1)
(2)
(3)
5.
If “Use the following IP address” (2) is selected, your Router
will need to be set up for a static IP connection type. Write the
address information the table below. You will need to enter this
information into the Router.
6.
If not already selected, select “Obtain an IP address
automatically” (1) and “Obtain DNS server address automatically”
(3). Click “OK”.
Your network settings are now configured for use with the Router.
80
Manually Configuring Network Settings
Manually Configuring Network Adapters in Windows 98SE or Me
1
1.
Right-click on “My Network Neighborhood” and select
“Properties” from the drop-down menu.
2
2.
Select “TCP/IP Settings” for your installed network adapter. You
will see the following window.
3
(3)
(1)
4
5
(2)
6
8
3.
If “Specify an IP address” is selected, your Router will need to
be set up for a static IP connection type. Write the address
information in the table below. You will need to enter this
information into the Router.
4.
Write the IP address and subnet mask from the “IP Address”
tab (3).
5.
Click the “Gateway” tab (2). Write the gateway address down in
the chart.
6.
Click the “DNS Configuration” tab (1). Write the DNS address(es)
in the chart.
7.
If not already selected,
select “Obtain IP
address automatically”
on the IP address tab.
Click “OK”.
Restart the computer. When the computer restarts, your network
adapter(s) are now configured for use with the Router.
81
9
10
section
7
Recommended Web Browser Settings
In most cases, you will not need to make any changes to your web
browser’s settings. If you are having trouble accessing the Internet or
the advanced web-based user interface, then change your browser’s
settings to the recommended settings in this section.
Microsoft® Internet Explorer 4.0 or Higher
1.
Start your web browser. Select “Tools” then “Internet Options”.
2.
In the “Internet Options” screen, there are three selections:
“Never dial a connection”, “Dial whenever a network connection
is not present”, and “Always dial my default connection”. If you
can make a selection, select “Never dial a connection”. If you
cannot make a selection, go to the next step.
3.
Under the “Internet Options” screen, click on “Connections” and
select “LAN Settings…”.
82
Recommended Web Browser Settings
4.
Make sure there are no check marks next to any of the displayed
options: “Automatically detect settings”, “Use automatic
configuration script”, and “Use a proxy server”. Click “OK”. Then
click “OK” again in the “Internet Options” page.
1
2
3
4
5
6
7
Netscape® Navigator® 4.0 or Higher
1. Start Netscape. Click on “Edit” then “Preferences”.
2.
In the “Preferences” window, click on “Advanced” then select
“Proxies”. In the “Proxies” window, select “Direct connection
to the Internet”.
83
9
10
section
8
Troubleshooting
Setup Assistant CD does not automatically start.
If the CD-ROM does not start the Setup Assistant automatically, it
could be that the computer is running other applications that are
interfering with the CD drive.
1.
If the Setup Assistant Welcome screen does not appear within
15-20 seconds, open up your CD-ROM drive by double-clicking
on the “My Computer” icon that is located on your desktop.
2.
Next, double-click on the CD-ROM drive that the Setup Assistant
CD has been placed in to start the installation.
3.
The Setup Assistant should start within a few seconds. If,
instead, a window appears showing the files on the CD,
double-click on the icon labeled “SetupAssistant”.
4.
If the Setup Assistant still does not start, reference the section
titled “Manually Configuring Network Settings” (page 77 of this
User Manual for an alternative setup method).
Setup Assistant cannot find my Router.
If the Setup Assistant is not able to find the Router during the
installation process, please check the following items:
1.
If the Setup Assistant is not able to find the Router during the
installation process, there may be third-party firewall software
installed on the computer attempting to access the Internet.
Examples of third-party firewall software are ZoneAlarm,
BlackICE PC Protection, McAfee Personal Firewall, and Norton
Personal Firewall. If you do have firewall software installed on
your computer, please make sure that you properly configure it.
You can determine if the firewall software is preventing Internet
access by temporarily turning it off. If, while the firewall is
disabled, Internet access works properly, you will need to change
the firewall settings to function properly when it is turned on.
Please refer to the instructions provided by the publisher of your
firewall software for instructions on configuring the firewall to
allow Internet access.
84
Troubleshooting
2.
3.
Unplug power to the Router for 10 seconds, and then plug the
power back into the Router. Ensure that the Router’s “router”
LED is on; it should be solid BLUE. If not, check to make sure
that the AC adapter is connected to the Router and plugged into
a wall outlet.
Ensure that you have a cable connected between (1) the network
(Ethernet) port on the back of the computer and (2) one of the “to
Wired Computers” ports on the back of the Router.
Note: The computer should NOT be connected to the port labeled
“to Modem” on the back of the Router.
4.
Try shutting down and restarting your computer, then rerunning
the Setup Assistant.
If the Setup Assistant is still unable to find the Router, reference
the section titled “Manually Configuring Network Settings” for
installation steps.
Setup Assistant cannot connect my Router to the Internet
1.
Use the troubleshooting suggestions within the Setup Assistant.
2.
If your ISP requires a user name and password, make sure
that you have typed in your user name and password correctly.
Some user names require that the ISP’s domain may be at the
end of the name. Example: “myname@myisp.com”. The “@myisp.
com” part of the user name may need to be typed as well as your
user name.
If you continue to have no Internet connection, reference the section
titled “Manually Configuring Network Settings” (page 77 of this User
Manual for an alternative setup method).
85
2
3
4
5
6
7
8
9
10
section
If the Setup Assistant is not able to connect the Router to the
Internet, please check the following items:
1
Troubleshooting
I can’t connect to the Internet wirelessly.
If you are unable to connect to the Internet from a wireless computer,
please check the following items:
1.
Look at the lights on your Router. They should be as follows:
• The “router” LED should be on.
• The “ADSL” light should be on, and not blinking.
• The “internet” LED should be on, and not blinking.
• The “Wireless” light should be on, not blinking.
2.
Open your wireless utility software by clicking on the icon in the
system tray at the bottom, right-hand corner of the screen.
3.
The exact window that opens will vary depending on the model of
wireless card you have; however, any of the utilities should have
a list of “Available Networks”—those wireless networks it can
connect to.
Does the name of your wireless network appear in the results?
Yes, my network name is listed—go to the troubleshooting solution
titled “I can’t connect to the Internet wirelessly, but my network name
is listed”.
No, my network name is not listed—go to the troubleshooting solution
titled “I can’t connect to the Internet wirelessly, and my network name
is not listed”.
86
Troubleshooting
I can’t connect to the Internet wirelessly, but my network name
is listed.
If the name of your network is listed in the “Available Networks” list,
please follow the steps below to connect wirelessly:
1.
Click on the correct network name in the “Available
Networks” list.
2.
If the network has security (encryption) enabled, you will
need to enter the network key. For more information regarding
security, see the section entitled “Changing the Wireless
Security Settings”.
3.
Within a few seconds, the tray icon in the lower, left-hand corner
of your screen should turn green, indication of a successful
connection to the network.
I can’t connect to the Internet wirelessly, and my network name
is not listed.
1.
2.
Temporarily move computer, if possible, five to 10 feet from the
Router. Close the wireless utility, and reopen it. If the correct
network name now appears under “Available Networks”, you may
have a range or interference problem. Please see the suggestions
discussed in the section titled “Placement of your N Wireless
Modem Router” of this User Manual.
Using a computer that is connected to the Router via a network
cable (as opposed to wirelessly), ensure that “Broadcast SSID” is
enabled. This setting is found on the Router’s wireless “Channel
and SSID” configuration page.
If you are still unable to access the Internet after completing these
steps, please contact Belkin Technical Support.
87
2
3
4
5
6
7
8
9
10
section
If the correct network name is not listed under “Available Networks”
in the wireless utility, please attempt the following troubleshooting
steps:
1
Troubleshooting
•
My wireless network performance is inconsistent.
•
Data transfer is sometimes slow.
•
Signal strength is poor.
•
Difficulty establishing and/or maintaining a Virtual Private
Network (VPN) connection.
Wireless technology is radio-based, which means connectivity
and the throughput performance between devices decreases
when the distance between devices increases. Other factors that
will cause signal degradation (metal is generally the worst culprit)
are obstructions such as walls and metal appliances. Note also
that connection speed may decrease as you move farther away from
the Router.
In order to determine if wireless issues are related to range, we
suggest temporarily moving the computer, if possible, five to 10 feet
from the Router.
Changing the wireless channel—Depending on local wireless traffic
and interference, switching the wireless channel of your network can
improve performance and reliability. The default channel the Router
is shipped with is channel 11; you may choose from several other
channels depending on your region. See the section on page 47
entitled “Changing the Wireless Channel” for instructions on how to
choose other channels.
Limiting the wireless transmit rate—Limiting the wireless transmit
rate can help improve the maximum wireless range and connection
stability. Most wireless cards have the ability to limit the transmission
rate. To change this property, go to the Windows Control Panel, open
“Network Connections” and double-click on your wireless card’s
connection. In the properties dialog, select the “Configure” button on
the “General” tab (Windows 98 users will have to select the wireless
card in the list box and then click “Properties”), then choose the
“Advanced” tab and select the rate property.
Wireless client cards are usually set to automatically adjust the
wireless transmit rate for you, but doing so can cause periodic
disconnects when the wireless signal is too weak; as a rule, slower
transmission rates are more stable. Experiment with different
connection rates until you find the best one for your environment.
Note that all available transmission rates should be acceptable for
browsing the Internet. For more assistance, see your wireless card’s
user manual.
88
Troubleshooting
I am having difficulty setting up Wired Equivalent Privacy (WEP)
security on my Belkin Router.
1.
Log into your Router.
2
Open your web browser and type in the IP address of the Router.
(The Router’s default is 192.168.2.1.) Log into your Router by
clicking on the “Login” button in the top right-hand corner of the
screen. You will be asked to enter your password. If you never set
a password, leave the “Password” field blank and click “Submit”.
3
Click the “Wireless” tab on the left of your screen. Select
the “Encryption” or “Security” tab to get to the security
settings page.
5
Select “128-bit WEP” from the drop-down menu.
3.
After selecting your WEP encryption mode, you can type in
your hex WEP key manually, or you can type in a passphrase
in the “Passphrase” field and click “Generate” to create a WEP
key from the passphrase. Click “Apply Changes” to finish. You
must now set all of your clients to match these settings. A hex
(hexadecimal) key is a mixture of numbers and letters from A-F
and 0-9. For 128-bit WEP, you need to enter 26 hex keys.
For example:
C3030FAF4BB2C3D44BC3D4E7E4 = 128-bit key
Click “Apply Changes” to finish. Encryption in the Wireless Router
is now set. Each of your computers on your wireless network will
now need to be configured with the same security settings.
WARNING: If you are configuring the Router from a computer with
a wireless client, you will need to ensure that security is turned on
for this wireless client. If this is not done, you will lose your
wireless connection.
Note to Mac users: Original Apple AirPort products support 64-bit
encryption only. Apple AirPort 2 products can support 64-bit or
128-bit encryption. Please check your Apple AirPort product to see
which version you are using. If you cannot configure your network
with 128-bit encryption, try 64-bit encryption.
89
4
6
7
8
9
10
section
2.
4.
1
Troubleshooting
I am having difficulty setting up Wired Equivalent Privacy (WEP)
security on a Belkin client card.
The client card must use the same key as the Router. For instance, if
your Router uses the key 00112233445566778899AABBCC, then the
client card must be set to the exact same key.
1.
Double-click the Signal Indicator icon to bring up the “Wireless
Network” screen.
2.
The “Advanced” button will allow you to view and configure more
options of the card.
3.
Once the “Advanced” button is clicked, the Belkin Wireless LAN
Utility will appear. This Utility will allow you to manage all the
advanced features of the Belkin Wireless Card.
4.
Under the “Wireless Network Properties” tab, select a network
name from the “Available Networks” list and click the “Properties”
button.
5.
Under “Data Encryption”, select “WEP”.
6.
Ensure the check box “The key is provided for me automatically”
at the bottom is unchecked. If you are using this computer to
connect to a corporate network, please consult your network
administrator if this box needs to be checked.
7.
Type your WEP key in the “Network key” box.
Important: A WEP key is a mixture of numbers and letters from
A-F and 0-9. For 128-bit WEP, you need to enter 26 keys. This
network key needs to match the key you assign to your Router.
For example:
C3030FAF4BB2C3D44BC3D4E7E4 = 128-bit key
8.
Click “OK”, and then “Apply” to save the settings.
If you are NOT using a Belkin wireless client card, please consult the
manufacturer’s user manual for that wireless client card.
90
Troubleshooting
1
Do Belkin products support WPA?
Note: To use WPA security, all your clients must be upgraded
to drivers and software that support it. At the time of this FAQ
publication, a security patch download is available, for free,
from Microsoft. This patch works only with the Windows XP
operating system.
2
Download the patch here:
4
http://www.microsoft.com/downloads
3
You also need to download the latest driver for your Belkin Wireless
802.11g Desktop or Notebook Network Card from the Belkin support
site. Other operating systems are not supported at this time.
Microsoft’s patch only supports devices with WPA-enabled drivers
such as Belkin 802.11g products
5
Download the latest driver at http://web.belkin.com/support.
7
I am having difficulty setting up Wireless Protected Access (WPA)
security on my Belkin Router for a home network.
From the “Security Mode” drop-down menu, select “WPA-PSK
(no server)”.
2.
For “Encryption Technique”, select “TKIP” or “AES”. This setting
will have to be identical on the clients that you set up.
3.
Enter your pre-shared key. This can be from eight to 63
characters and can be letters, numbers, symbols, or spaces.
This same key must be used on all of the clients that you set up.
For example, your PSK might be something like: “Smith family
network key”.
4.
Click “Apply Changes” to finish. You must now set all clients to
match these settings.
91
8
9
10
section
1.
6
Troubleshooting
I am having difficulty setting up Wireless Protected Access (WPA)
security on a Belkin wireless client card for a home network.
Clients must use the same key that the Router uses. For instance, if
the key is “Smith Family Network Key” in the Router, the clients must
also use that same key.
1.
Double-click the Signal Indicator icon to bring up the “Wireless
Network” screen. The “Advanced” button will allow you to view
and configure more options of your card.
2.
Once the “Advanced” button is clicked, the Belkin Wireless Utility
will appear. This Utility will allow you to manage all the advanced
features of the Belkin Wireless Card.
3.
Under the “Wireless Network Properties” tab, select a
network name from the “Available Networks” list and click the
“Properties” button.
4.
Under “Network Authentication”, select “WPA-PSK (no server).
5.
Type your WPA key in the “Network key” box.
Important: WPA-PSK is a mixture of numbers and letters
from A-Z and 0-9. For WPA-PSK you can enter eight to 63
characters. This network key needs to match the key you assign
to your Router.
6.
Click “OK, then “Apply” to save the settings.
92
Troubleshooting
I am NOT using a Belkin client card for a home network and
I am having difficulty setting up Wireless Protected Access
(WPA) security.
If you are not using a Belkin Wireless Desktop or Wireless Notebook
Network Card that is not equipped with WPA-enabled software, a
file from Microsoft called “Windows XP Support Patch for Wireless
Protected Access” is available for free download. Download the
patch from Microsoft by searching the knowledge base for Windows
XP WPA.
1
2
3
4
Note: The file that Microsoft has made available works only with
Windows XP. Other operating systems are not supported at this
time. You also need to ensure that the wireless card’s manufacturer
supports WPA and that you have downloaded and installed the latest
driver from their support site.
5
Supported Operating Systems:
• Windows XP Professional
• Windows XP Home Edition
7
Under Windows XP, click “Start > Control Panel >
Network Connections”.
2.
Right-click on the “Wireless Networks” tab. Ensure the “Use
Windows to configure my wireless network settings” check
box is checked.
3.
Under the “Wireless Networks” tab, click the “Configure”.
4.
For a home or small business user, select “WPA-PSK” under
“Network Administration”.
Note: Select WPA (with radius server) if you are using this computer
to connect to a corporate network that supports an authentication
server such as a radius server. Please consult your network
administrator for further information.
5.
Select “TKIP” or “AES” under “Date Encryption”. This setting will
have to be identical to the Router that you set up.
6.
Type in your encryption key in the “Network key” box.
Important: Enter your pre-shared key. This can be from eight to 63
characters and can be letters, numbers, or symbols. This same key
must be used on all of the clients that you set up.
7.
Click “OK” to apply settings.
93
8
9
10
section
1.
6
Troubleshooting
What’s the difference between 802.11b, 802.11g, 802.11a, and
draft 802.11n?
Currently there are four levels of wireless networking standards,
which transmit data at very different maximum speeds. Each is
based on the designation for certifying network standards. The
most common wireless networking standard, 802.11b, transmits
information at 11Mbps; 802.11a and 802.11g work at 54Mbps; and
draft 802.11n works at 108Mbps. See the chart on the next page for
more detailed information.
94
Troubleshooting
1
Speed*
G
(802.11g)
Up to 54Mbps*
Frequency
Wireless
Technology
Wireless Comparison Chart
Common
household devices
such as cordless
phones and
microwave ovens
may interfere with
the unlicensed
band 2.4GHz
G Plus MIMO
(802.11g with
MIMO MRC)
N MIMO
(draft 802.11n
with MIMO)
N1 MIMO
(draft 802.11n
with MIMO)
Up to 54Mbps*
Up to 300Mbps*
Up to 300Mbps*
2
3
4
5
Common
household devices
such as cordless
phones and
microwave ovens
may interfere with
the unlicensed
band 2.4GHz
Common
household devices
such as cordless
phones and
microwave ovens
may interfere with
the unlicensed
band 2.4GHz
Common
household devices
such as cordless
phones and
microwave ovens
may interfere with
the unlicensed
band 2.4GHz
6
7
Compatibility
Coverage*
Up to 400 ft.*
Common—
Better coverage
widespread use for and consistent
Internet sharing
speed at range
Compatible with
802.11b/g
Compatible with
draft 802.11n**
and 802.11b/g
Compatible with
draft 802.11n**
and 802.11b/g
9
10
Up to 1,000 ft.*
Up to 1,200 ft.*
Up to 1,400 ft.*
Enhanced speed
and coverage
Leading edge—
best coverage
and throughput
*Distance and connection speeds will vary depending on your networking environment.
**This Router is compatible with products based on the same version of the draft
802.11n specifications, and may require a software upgrade for best results.
95
section
Compatible with
802.11b/g
Advantage
8
Troubleshooting
Technical Support
You can find technical-support information on our website,
www.belkin.com, by navigating to the tech-support section.
If you want to contact technical support by phone, please call the
number you need from the list below*.
*Local rates apply.
Country
Number
Internet adress
AUSTRIA
0820 200766
http://www.belkin.com/uk/networking/
BELGIUM
07 07 00 073
http://www.belkin.com/nl/networking/
CZECH REPUBLIC
239 000 406
http://www.belkin.com/uk/networking/
DENMARK
701 22 403
http://www.belkin.com/uk/networking/
FINLAND
00800 - 22 35 54 60
http://www.belkin.com/uk/networking/
FRANCE
08 - 25 54 00 26
http://www.belkin.com/fr/networking/
GERMANY
0180 - 500 57 09
http://www.belkin.com/de/networking/
GREECE
00800 - 44 14 23 90
http://www.belkin.com/uk/networking/
HUNGARY
06 - 17 77 49 06
http://www.belkin.com/uk/networking/
ICELAND
800 8534
http://www.belkin.com/uk/networking/
IRELAND
0818 55 50 06
http://www.belkin.com/uk/networking/
ITALY
02 - 69 43 02 51
http://www.belkin.com/it/support/tech/issues_more.asp
LUXEMBOURG
34 20 80 85 60
http://www.belkin.com/uk/networking/
NETHERLANDS
0900 - 040 07 90
€0.10 per minute
http://www.belkin.com/nl/networking/
NORWAY
81 50 0287
http://www.belkin.com/uk/networking/
POLAND
00800 - 441 17 37
http://www.belkin.com/uk/networking/
PORTUGAL
707 200 676
http://www.belkin.com/uk/networking/
RUSSIA
495 580 9541
http://www.belkin.com/networking/
SOUTH AFRICA
0800 - 99 15 21
http://www.belkin.com/uk/networking/
SPAIN
902 - 02 43 66
http://www.belkin.com/es/support/tech/networkingsupport.asp
SWEDEN
07 - 71 40 04 53
http://www.belkin.com/se/support/tech/networkingsupport.asp
SWITZERLAND
08 - 48 00 02 19
http://www.belkin.com/uk/networking/
UNITED KINGDOM
0845 - 607 77 87
http://www.belkin.com/uk/networking/
OTHER COUNTRIES
+44 - 1933 35 20 00
96
Information
Belkin International, Inc., Limited Lifetime Product Warranty
1
What this warranty covers.
Belkin International, Inc. (“Belkin”) warrants to the original purchaser of this
Belkin product that the product shall be free of defects in design, assembly,
material, or workmanship.
2
What the period of coverage is.
Belkin warrants the Belkin product for the lifetime of the product.
4
What will we do to correct problems?
Product Warranty.
Belkin will repair or replace, at its option, any defective product free of charge
(except for shipping charges for the product).
5
What is not covered by this warranty?
All above warranties are null and void if the Belkin product is not provided
to Belkin for inspection upon Belkin’s request at the sole expense of
the purchaser, or if Belkin determines that the Belkin product has been
improperly installed, altered in any way, or tampered with. The Belkin Product
Warranty does not protect against acts of God such as flood, lightning,
earthquake, war, vandalism, theft, normal-use wear and tear, erosion,
depletion, obsolescence, abuse, damage due to low voltage disturbances
(i.e. brownouts or sags), non-authorized program, or system equipment
modification or alteration.
7
1. Contact Belkin Tech Support at the number listed on page 99 within 15
days of the Occurrence. Be prepared to provide the following information:
a. The part number of the Belkin product.
b. Where you purchased the product.
c. When you purchased the product.
d. Copy of original receipt.
2. Your Belkin Customer Service Representative will then instruct you on
how to forward your receipt and Belkin product and how to proceed
with your claim.
97
6
8
9
10
section
How to get service.
To get service for your Belkin product you must take the following steps:
3
Information
Belkin reserves the right to review the damaged Belkin product. All costs of shipping
the Belkin product to Belkin for inspection shall be borne solely by the purchaser.
If Belkin determines, in its sole discretion, that it is impractical to ship the damaged
equipment to Belkin, Belkin may designate, in its sole discretion, an equipment
repair facility to inspect and estimate the cost to repair such equipment. The cost,
if any, of shipping the equipment to and from such repair facility and of such
estimate shall be borne solely by the purchaser. Damaged equipment must remain
available for inspection until the claim is finalized. Whenever claims are settled,
Belkin reserves the right to be subrogated under any existing insurance policies the
purchaser may have.
How state law relates to the warranty.
THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN. THERE ARE
NO OTHER WARRANTIES, EXPRESSED OR, EXCEPT AS REQUIRED BY LAW,
IMPLIED, INCLUDING THE IMPLIED WARRANTY OR CONDITION OF QUALITY,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND SUCH
IMPLIED WARRANTIES, IF ANY, ARE LIMITED IN DURATION TO THE TERM OF
THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the
above limitations may not apply to you.
IN NO EVENT SHALL BELKIN BE LIABLE FOR INCIDENTAL, SPECIAL, DIRECT,
INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS, BUT NOT
LIMITED TO, LOST BUSINESS OR PROFITS ARISING OUT OF THE SALE OR USE
OF ANY BELKIN PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
This warranty gives you specific legal rights, and you may also have other rights,
which may vary from state to state. Some states do not allow the exclusion or
limitation of incidental, consequential, or other damages, so the above limitations
may not apply to you
FOR USE IN
AT
BE CY
EE
FI
CZ DK
FR DE GR
You can find the declaration of conformity for this product at
the following URL,
HU IE
LV
LT
http://www.belkin.com/doc/
LU MT NL PL
PT
IT
SK
SI
IS
LI NO CH BG
ES
SE GB
RO TR
For information on product disposal please refer to
http://environmental.belkin.com
98
OPERATES ON
CHANNELS 1-13
N Wireless
Modem Router
Belkin Tech Support
UK: 0845 607 77 87
Europe: www.belkin.com/support
Belkin Ltd.
Express Business Park
Shipton Way, Rushden
NN10 6GL, United Kingdom
+44 (0) 1933 35 2000
+44 (0) 1933 31 2000 fax
Belkin SAS
130 rue de Silly
92100 Boulogne-Billancourt,
France
+33 (0) 1 41 03 14 40
+33 (0) 1 41 31 01 72 fax
Belkin GmbH
Hanebergstrasse 2
80637 Munich
Germany
+49 (0) 89 143405 0
+49 (0) 89 143405 100 fax
Belkin Iberia
C/ Anabel Segura, 10 planta baja, Of. 2
28108, Alcobendas, Madrid
Spain
+34 91 791 23 00
+34 91 490 23 35 fax
Belkin Italy & Greece
Via Carducci, 7
Milano 20123
Italy
+39 02 862 719
+39 02 862 719 fax
Belkin B.V.
Boeing Avenue 333
1119 PH Schiphol-Rijk,
Netherlands
+31 (0) 20 654 7300
+31 (0) 20 654 7349 fax
© 2007 Belkin International, Inc. All rights reserved. All trade names are registered trademarks of
respective manufacturers listed. Mac, Mac OS, Apple, and AirPort are trademarks of Apple Computer,
Inc., registered in the U.S. and other countries. Windows, Microsoft, and NT are either registered
trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
P75555ea
Download PDF