Empire Heating Systems | DVC-35IPT-1 | Owner`s manual | Empire Heating Systems DVC-35IPT-1 Owner`s manual

INSTALLATION INSTRUCTIONS
AND
OWNER’S MANUAL
FAN TYPE
Direct Vent
Wall Furnace
Model
DVC-35T-1
DVC-35IPT-1
Installer: Leave this manual with the appliance.
Consumer:Retain this manual for future reference.
Thisappliancemaybeinstalledinanaftermarket,
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by
state or local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless
a certified kit is used.
WARNING: If not installed, operated and
maintained in accordance with the manufacturer’s instructions, this product could expose you
to substances in fuel or from fuel combustion
which can cause death or serious illness.
WARNING: If the information in these instructions are not followed exactly, a fire or explosion
may result causing property damage, personal
injury or loss of life.
— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call
the fire department.
— Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
Page 1
TABLE OF CONTENTS
Section
Page
Important Safety Information.......................................................................................................................3
Safety Information for Users of LP Gas.......................................................................................................4
Requirements for Massachusetts...................................................................................................................5
Introduction...................................................................................................................................................6
Specifications................................................................................................................................................6
Gas Supply................................................................................................................................................ 7-8
Clearances ....................................................................................................................................................8
Installation Instructions........................................................................................................................... 9-11
DVC-35T Standing Pilot Lighting Instructions .........................................................................................12
DVC-35IPT Intermittent Pilot Lighting Instructions . ...............................................................................13
Pilot Flame Characteristics ........................................................................................................................14
Main Burner Flame Characteristics ...........................................................................................................15
Wiring................................................................................................................................................... 15-16
Service and Maintenance Suggestions........................................................................................................17
DVC-35IPT Intermittent Pilot Sequence of Operation...............................................................................18
DVC-35IPT Intermittent Pilot System Troubleshooting Sequence............................................................19
How to Order Repair Parts..........................................................................................................................20
Parts List ....................................................................................................................................................20
Parts View...................................................................................................................................................21
Service Notes........................................................................................................................................ 22-23
Page 2
13119-10-0709
IMPORTANT SAFETY INFORMATION
This Is a Heating Appliance
Do Not Operate This Appliance Without Front Panel Installed.
•
•
•
•
•
•
•
•
Due to high temperatures the appliance should be located
out of traffic and away from furniture and draperies.
Children and adults should be alerted to the hazards of
high surface temperatures and should stay away to avoid
burns or clothing ignition.
Young children should be carefully supervised when they
are in the same room as the appliance.
Clothing or other flammable material should not be placed
on or near the appliance.
Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance.
Keep burner and control compartment clean.
Vent cap hot while furnace is in operation.
Installation and repair should be done by a qualified
service person. The appliance should be inspected
before use and at least annually by a qualified service
person. More frequent cleaning may be required due to
excessive lint from carpeting, bedding materials, etc. It
is imperative that control compartments, burners and
circulating air passageways of the appliance be kept
clean.
•
•
•
•
•
•
Do not put anything around the furnace that will obstruct the flow of combustion and ventilation air.
Do keep the appliance area clear and free from combustible material, gasoline and other flammable vapors and
liquids.
Do examine venting system periodically and replace
damaged parts.
Do make a periodic visual check of pilot and burners.
Clean and replace damaged parts.
CAUTION: Pilot hole cover must be kept tightly closed
during operation.
Do not use this heater if any part has been under water.
Immediately call a qualified service technician to inspect
the heater and to replace any part of the control system
and any gas control which has been under water.
• Important: This furnace has a washable permanent
type filter which should be cleaned at least once per
year before the heating season. For dirty or high use
areas more frequent cleaning is required.
VENT KIT INFORMATION
Attention: The DVC-35T and DVC-35IPT direct vent wall furnaces are provided with vent kit, DV4T-59-1 for wall depths of 5” to
9”. For wall depths greater than 9”, refer to Accessories, Page 6. Listed below are the vent kits.
Attention: The minimum wall depth for installation of a DVC-35T and DVC-35IPT must be 5”. If the wall depth is less than 5”
you can order DV-822, refer to Accessories, Page 6 or refer to Figure 10 and Figure 11 with accompanying text, Page 11.
Vent Kits
No.
13119-10-0709
Part
DV4T-59-1
DV4T-812-1
DV4T-1219-1
1
Outlet Tube - Inner
13057
13057
13058
2
Gasket - Outer Collar
M-177
M-177
M-177
3
Outlet Tube - Inner
13104
13104
13105
4
Inlet Tube - Inner
13062
13062
13063
5
Gasket - Inlet Collar
M-178
M-178
M-178
13107
6
Inlet Tube - Inner
13106
13106
7
Inlet Tube - Outer
13064
13065
13066
8
Outlet Tube - Outer
13059
13060
13061
9
Vent Cap
13053
13053
13053
Hardware Kit
13078
13078
13078
Page 3
SAFETY INFORMATION FOR USERS OF LP-GAS
Propane (LP-Gas) is a flammable gas which can cause fires
and explosions. In its natural state, propane is odorless and
colorless. You may not know all the following safety precautions which can protect both you and your family from an
accident. Read them carefully now, then review them point
by point with the members of your household. Someday when
there may not be a minute to lose, everyone’s safety will depend
on knowing exactly what to do. If, after reading the following
information, you feel you still need more information, please
contact your gas supplier.
LP-GAS WARNING ODOR
If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.
That’s your signal to go into immediate action!
•
Do not operate electric switches, light matches, use your
phone. Do not do anything that could ignite the gas.
• Get everyone out of the building, vehicle, trailer, or area. Do
that IMMEDIATELY.
• Close all gas tank or cylinder supply valves.
• LP-Gas is heavier than air and may settle in low areas such
as basements. When you have reason to suspect a gas leak,
keep out of basements and other low areas. Stay out until
firefighters declare them to be safe.
• Use your neighbor’s phone and call a trained LP-Gas service
person and the fire department. Even though you may not
continue to smell gas, do not turn on the gas again. Do not
re-enter the building, vehicle, trailer, or area.
• Finally, let the service man and firefighters check for escaped
gas. Have them air out the area before you return. Properly
trained LP-Gas service people should repair the leak, then
check and relight the gas appliance for you.
no odor detected - odor fade
Some people cannot smell well. Some people cannot smell the
odor of the chemical put into the gas. You must find out if you
can smell the odorant in propane. Smoking can decrease your
ability to smell. Being around an odor for a time can affect your
sensitivity or ability to detect that odor. Sometimes other odors
in the area mask the gas odor. People may not smell the gas odor
or their minds are on something else. Thinking about smelling a
gas odor can make it easier to smell.
The odorant in LP-gas is colorless, and it can fade under some
circumstances. For example, if there is an underground leak, the
movement of the gas through soil can filter the odorant. Odorants
in LP-Gas also are subject to oxidation. This fading can occur if
there is rust inside the storage tank or in iron gas pipes.
The odorant in escaped gas can adsorb or absorb onto or into walls,
masonry and other materials and fabrics in a room. That will take
some of the odorant out of the gas, reducing its odor intensity.
LP-Gas may stratify in a closed area, and the odor intensity could
vary at different levels. Since it is heavier than air, there may be
more odor at lower levels. Always be sensitive to the slightest gas
odor. If you detect any odor, treat it as a serious leak. Immediately
go into action as instructed earlier.
some points to remember
•
Learn to recognize the odor of LP-gas. Your local LP-Gas
Dealer can give you a “Scratch and Sniff” pamphlet. Use it
to find out what the propane odor smells like. If you suspect
that your LP-Gas has a weak or abnormal odor, call your
LP-Gas Dealer.
•
If you are not qualified, do not light pilot lights, perform
service, or make adjustments to appliances on the LP-Gas
system. If you are qualified, consciously think about the odor
of LP-Gas prior to and while lighting pilot lights or performing service or making adjustments.
•
Sometimes a basement or a closed-up house has a musty
smell that can cover up the LP-Gas odor. Do not try to light
pilot lights, perform service, or make adjustments in an area
where the conditions are such that you may not detect the
odor if there has been a leak of LP-Gas.
•
Odor fade, due to oxidation by rust or adsorption on walls
of new cylinders and tanks, is possible. Therefore, people
should be particularly alert and careful when new tanks or
cylinders are placed in service. Odor fade can occur in new
tanks, or reinstalled old tanks, if they are filled and allowed
Page 4
to set too long before refilling. Cylinders and tanks which
have been out of service for a time may develop internal rust
which will cause odor fade. If such conditions are suspected
to exist, a periodic sniff test of the gas is advisable. If you
have any question about the gas odor, call your lp-gas
dealer. A periodic sniff test of the lp-gas is a good safety
measure under any condition.
•
If, at any time, you do not smell the LP-Gas odorant and you
think you should, assume you have a leak. Then take the same
immediate action recommended above for the occasion when
you do detect the odorized LP-Gas.
•
If you experience a complete “gas out,” (the container is
under no vapor pressure), turn the tank valve off immediately.
If the container valve is left on, the container may draw in
some air through openings such as pilot light orifices. If this
occurs, some new internal rusting could occur. If the valve is
left open, then treat the container as a new tank. Always be
sure your container is under vapor pressure by turning it off
at the container before it goes completely empty or having
it refilled before it is completely empty.
13119-10-0709
REQUIREMENTS FOR MASSACHUSETTS
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7) feet
above finished grade in the area of the venting, including but
not limited to decks and porches, the following requirements
shall be satisfied:
3. SIGNAGE. A metal or plastic identification plate shall be
permanently mounted to the exterior of the building at a
minimum height of eight (8) feet above grade directly in
line with the exhaust vent terminal for the horizontally
vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2)
inch in size, “GAS VENT DIRECTLY BELOW. KEEP
CLEAR OF ALL OBSTRUCTIONS”.
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal
vented gas fueled equipment, the installing plumber or
gasfitter shall observe that a hard wired carbon monoxide
detector with an alarm and battery back-up is installed on
the floor level where the gas equipment is to be installed.
In addition, the installing plumber or gasfitter shall observe
that a battery operated or hard wired carbon monoxide
detector with an alarm is installed on each additional
level of the dwelling, building or structure served by
the side wall horizontal vented gas fueled equipment. It
shall be the responsibility of the property owner to secure
the services of qualified licensed professionals for the
installation of hard wired carbon monoxide detectors
4. INSPECTION. The state or local gas inspector of the
side wall horizontally vented gas fueled equipment shall
not approve the installation unless, upon inspection, the
inspector observes carbon monoxide detectors and signage
installed in accordance with the provisions of 248 CMR
5.08(2)(a) 1 through 4.
a. In the event that the side wall horizontally vented gas
fueled equipment is installed in a crawl space or an
attic, the hard wired carbon monoxide detector with
alarm and battery back-up may be installed on the
next adjacent floor level.
1. The equipment listed in Chapter 10 entitled
“Equipment Not Required To Be Vented” in the
most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented
gas fueled equipment installed in a room or
structure separate from the dwelling, building or
structure used in whole or in part for residential
purposes.
b. In the event that the requirements of this subdivision
can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days
to comply with the above requirements; provided,
however, that during said thirty (30) day period, a
battery operated carbon monoxide detector with an
alarm shall be installed.
2.APPROVED CARBON MONOXIDE DETECTORS.
Each carbon monoxide detector as required in accordance
with the above provisions shall comply with NFPA 720
and be ANSI/UL 2034 listed and IAS certified.
(c) MANUFACTURER REQUIREMENTS - GAS
EQUIPMENT VENTING SYSTEM PROVIDED.
When the manufacturer of Product Approved side
wall horizontally vented gas equipment provides a
venting system design or venting system components
with the equipment, the instructions provided by the
manufacturer for installation of the equipment and
the venting system shall include:
1. Detailed instructions for the installation of the
venting system design or the venting system
components; and
2.A complete parts list for the venting system design
or venting system.
13119-10-0709
(b) EXEMPTIONS: The following equipment is exempt
from 248 CMR 5.08(2)(a)1 through 4:
(e) A copy of all installation instructions for all Product
Approved side wall horizontally vented gas fueled
equipment, all venting instructions, all parts lists for
venting instructions, and/or all venting design instructions shall remain with the appliance or equipment
at the completion of the installation.
Page 5
INTRODUCTION
Introduction
Always consult your local Building Department regarding regulations,
codes or ordinances which apply to the installation of a direct vent wall
furnace.
Instructions to Installer
1. Installer must leave instruction manual with owner after
installation.
2. Installer must have owner fill out and mail warranty card supplied
with furnace.
3. Installer should show owner how to start and operate furnace and
thermostat.
Warning:
Any change to this furnace or its control can be dangerous. This
is a heating appliance and any panel, door or guard removed for
servicing an appliance must be replaced prior to operating the
appliance.
General Information
This furnace is design certified in accordance with American National
Standard/CSA Standard Z21.86 and CSA 2.32 by the Canadian Standards
Association, as a fan type direct vent wall furnace to be installed according
to these instructions.
Any alteration of the original design, installed other than as shown in
these instructions or use with a type of gas not shown on the rating plate
is the responsibility of the person and company making the change.
Important
All correspondence should refer to complete Model No., Serial No. and
type of gas.
Notice: During initial firing of this unit, its paint will bake out and smoke
will occur. To prevent triggering of smoke alarms, ventilate the room in
which the unit is installed.
Installation on Rugs and Tile
If this appliance is installed directly on carpeting, tile or other combustible
material other than wood flooring the appliance shall be installed on a metal
or wood panel extending the full width and depth of the appliance.
The base referred to above does not mean the fire-proof base as used on
wood stoves. The protection is for rugs that are extremely thick and light
colored tile.
Installation in Residential Garages
Gas utilization equipment in residential garages shall be installed so that
all burners and burner ignition devices are located not less than 18” above
the floor.
Such equipment shall be located, or protected, so it is not subject to physical
damage by a moving vehicle.
Qualified Installing Agency
Installation and replacement of gas piping, gas utilization equipment or
accessories and repair and servicing of equipment shall be performed
only by a qualified agency. The term “qualified agency” means any
individual, firm, corporation or company which either in person or through
a representative is engaged in and is responsible for (a) the installation
or replacement of gas piping or (b) the connection, installation, repair or
servicing of equipment, who is experienced in such work, familiar with
all precautions required and has complied with all the requirements of the
authority having jurisdiction.
State of Massachusetts: The installation must be made by a licensed
plumber or gas fitter in the Commonwealth of Massachusetts.
The installation must conform with local codes or, in the absence of local
codes, with the National Fuel Gas Code ANSI Z223.1/NFPA 54* Natural
Gas and Propane Installation Code, CSA B149.1.
*Available from the American National Standards Institute, Inc., 11 West
42nd St., New York, N.Y. 10036.
High Altitudes
For altitudes/elevations above 2,000 feet, input ratings should be reduced
at the rate of 4 percent for each 1,000 feet above sea level. For Canadian
high altitude applications, this appliance is suitable for installation at
elevations between 0 feet and 4,500 feet without change.
Piezo Pilot Ignitor Instructions
Depressing the red button completely causes a spark to occur at the pilot. This
is a substitute for a match which requires opening the pilot hole cover.
To light the pilot, it is important that the electrode be 1/8” from the
thermocouple. The spark must occur at the point the burner flame hits the
thermocouple. The end of the electrode will be red hot with the pilot on.
On a new installation with air in the gas line, it is suggested that a match
be used. The match will light the pilot faster than the piezo under this
condition.
SPECIFICATIONS
Model
DVC-35T
DVC-35IPT
Input BTU/HR
35,000
35,000
Height
72 1/2”
72 1/2”
Width
14 1/8”
14 1/8”
Depth
10 3/8”
10 3/8”
1/2” Pipe
1/2” Pipe
275
275
Gas Inlet
CFM
Accessories
SOR-1
Register, Side Outlet
SOK-1
Side Outlet Kit, 10” (25.4cm) Boot Assembly with Register
*DV-822
Vinyl Siding Vent Kit
* DV-822, Vinyl siding vent kit, adds 3” to wall depth. You must include the three (3) additional inches for TOTAL wall depth when ordering a
vent kit.
Page 6
13119-10-0709
GAS SUPPLY
Locating Gas Supply
The gas line can enter the unit either through the floor or outside
wall. The gas line opening should be made at this time. Location
of the opening will be determined by the position of floor joists
and the valve and union used for servicing.
Recommended Gas Pipe Diameter
Pipe Length
Schedule 40 Pipe
Tubing, Type L
Inside Diameter
Outside Diameter
Nat.
L.P.
Nat.
L.P.
0-10 feet
1/2”
3/8”
1/2”
3/8”
0-3 meters
12.7mm 9.5mm 12.7mm 9.5mm
10-40 feet
1/2”
1/2”
5/8”
1/2”
4-12 meters 12.7mm 12.7mm 15.9mm 12.7mm
40-100 feet
1/2”
1/2”
3/4”
1/2”
13-30 meters 12.7mm 12.7mm
19mm 12.7mm
100-150 feet
3/4”
1/2”
7/8”
3/4”
31-46 meters 19mm 12.7mm 22.2mm 19mm
Note: Never use plastic pipe. Check to confirm whether your local
codes allow copper tubing or galvanized.
Note: Since some municipalities have additional local codes, it is
always best to consult your local authority and installation code.
The use of the following gas connectors is recommended:
—ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing
and Fittings
—ANS Z21.45 Assembled Flexible Appliance Connectors of
Other Than All-Metal Construction
The above connectors may be used if acceptable by the authority
having jurisdiction. The state of Massachusetts requires that a flexible
appliance connector cannot exceed three feet in length.
Installing a New Main Gas Cock
Each appliance should have its own manual gas cock.
A manual main gas cock should be located in the vicinity of
the unit. Where none exists, or where its size or location is not
adequate, contact your local authorized installer for installation
or relocation.
Compounds used on threaded joints of gas piping shall be resistant
to the action of liquefied petroleum gases. The gas lines must be
checked for leaks by the installer. This should be done with a soap
solution watching for bubbles on all exposed connections, and if
unexposed, a pressure test should be made.
Never use an exposed flame to check for leaks. Appliance must
be disconnected from piping at inlet of control valve and pipe
capped or plugged for pressure test. Never pressure test with
appliance connected; control valve will sustain damage!
A gas valve and ground joint union should be installed in the gas
line upstream of the gas control to aid in servicing. It is required
by the National Fuel Gas Code that a drip line be installed near
the gas inlet. This should consist of a vertical length of pipe tee
connected into the gas line that is capped on the bottom in which
condensation and foreign particles may collect.
Figure 2
Method of Installing a Tee Fitting Sediment Trap
Figure 1
Consult the current National Fuel Gas Code, ANSI Z223.1 CAN/
CGA-B149 (.1 or .2) installation code.
13119-10-0709
Pressure Testing of the Gas Supply System
1. To check the inlet pressure to the gas valve, a 1/8” N.P.T.
plugged tapping, accessible for test gauge connection, must be
placed immediately upstream of the gas supply connection to
the appliance.
2. The appliance and its individual shutoff valve must be
disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of 1/2
psig (3.5 kPa).
3. The appliance must be isolated from the gas supply piping
system by closing its individual manual shutoff valve during
any pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig (3.5 kPa).
Attention! If one of the above procedures results in pressures in
excess of 1/2 psig (14” w.c.) (3.5 kPa) on the appliance gas valve,
it will result in a hazardous condition.
Page 7
pressure of approximately 4.0” w.c. (.996kPa) for DVC-35T and
3.5” w.c. (.871kPa) for DVC-35IPT at the valve outlet with the
inlet pressure to the valve from a minimum of 5.0” w.c. (1.245kPa)
for the purpose of input adjustment to a maximum of 7.0” w.c.
(1.743kPa). Propane gas models will have a manifold pressure
approximately 10.0” w.c. (2.49kPa) at the valve outlet with the inlet
pressure to the valve from a minimum of 11.0” w.c. (2.739kPa)
for the purpose of input adjustment to a maximum of 13.0” w.c.
(3.237kPa).
A 1/8” N.P.T. plugged tapping, accessible for test gauge connection,
is located on the outlet side of the gas control.
Figure 3
Checking Manifold Pressure
Both Propane and Natural gas valves have a built-in pressure
regulator in the gas valve. Natural gas models will have a manifold
The built-in regulator comes on at approximately 1/4th pressure
and full on in 10 seconds.
CLEARANCES
Clearances
1. In selecting a location for installation, it is necessary to provide
adequate accessibility clearances for servicing and proper
installation. A front clearance of 36” is recommended. Do not
block outlet or inlet air openings on the front grill.
2. The DV4T-59-1, 5” to 9” wall depth is the standard vent kit
provided with the DVC-35T or DVC-35IPT. See Accessories
Page 6 to order vent kits for wall depths of 8” to 12” or 12”
to 19”. The use of tubes not supplied by the manufacturer
results in unsatisfactory performance.
3. The DVC-35T and DVC-35IPT can be attached to the wall or
recessed into the wall up to 9 1/2” in depth but the minimum
5” vent/air intake system wall depth must be maintained.
Example: If furnace is recessed into the wall at a depth of
9 1/2”, the minimum wall depth behind the furnace must be
5”.
4. The wall in which the furnace is recessed has (0) zero clearance
to the furnace sides and top.
5. When using side discharge registers, SOR-1 or SOK-1, the
furnace cannot be recessed into the wall.
6. Clearance to sidewall or combustible material is 4”.
7. Ceiling clearance is 4”.
8. Floor and rear wall clearance is (0) zero inches.
9. Clearance of 18” is required to sidewall or combustible material
when flush mounted SOR-1, side outlet register is used.
10. The minimum distance from the center of the vent cap to the
nearest outside corner or obstruction is 12”.
Figure 4
The vent terminal of this direct vent appliance shall be located at
least 9” from any opening through which flue gases could enter a
building. The bottom of the vent terminal and the air intake shall
be located at least 12” above grade. See vent location, Figure 4.
Warning: The nearest point of the vent cap should be
a minimum horizontal distant of six (6) feet from any
pressure regulator. In case of regulator malfunction, the
six (6) feet distance will reduce the chance of gas entering
the vent cap.
Page 8
13119-10-0709
INSTALLATION INSTRUCTIONS
Locating Wall Opening
The furnace is to be located on an outside wall. Locate wall studs so
that wall opening will be located between wall studs. The furnace
is 14 1/8” in width and can be recessed between standard 16” on
center wall studs. The wall opening required as shown in Figure 5
is a diameter of 7 1/2”.
8.Drill two (2) 1/8” diameter holes in the wall and attach the
register with two (2) 10 x 1 1/2” provided screws.
9.Installation of SOK-1 is completed.
A template is provided in furnace carton for positioning furnace
on the wall. Also, refer to Figure 5 and Figure 7 for positioning the
furnace on wall and for locating gas line connection.
Installing Optional Side Outlets
Side outlet register, SOR-1 may be installed on one or both sides
of the furnace at the required clearances of 18” to adjacent wall or
combustible material as shown in Figure 6.
1.Turn “OFF” all electric power to the furnace.
2.Remove the front panel from the furnace.
3.Remove the two (2) 8 x 3/8” screws that attach the inner shield
cover plate to the inner shield.
4.Scribe a line between the four dimples on the outer casing side
to form a square.
5.Drill a pilot hole within the scribed square on the outer casing.
Remove the sheet metal within the scribed square with a tin
snips or comparable tool. Attention! Do not cut the electrical
wires located between the outer casing and the inner shield.
6.Insert the 5” x 5” inner boot through the outer casing. Align the
clearance holes on the inner boot with the screw holes on the
inner shield. Attach inner boot to inner shield with two (2) 8 x
3/8” screws removed in Step 3.
7.Place the register over the 5 1/2” square opening with the louvers
set for the desired direction and mark the mounting holes using
the register as a template.
8.Drill two (2) 1/8” diameter holes in cabinet side and attach the
register with two (2) 10 x 1” provided screws.
9.Installation of SOR-1 is completed.
Side outlet kit, SOK-1, 10” boot assembly with register, for warm
air discharge into an adjoining room may be installed on either side
of the furnace at the required clearance of 4” to adjacent wall as
shown in Figure 6.
To install SOK-1, please use Steps 1 through 5 in the SOR-1
instructions for DVC-35T furnaces. Now, use the following Steps
to complete installation of the SOK-1.
1.Using the inner and outer boots as hole templates, mark and
drill four (4) 1/8” (3mm) diameter holes in the inner shield and
four (4) 1/8” (3mm) diameter holes in the cabinet side.
2.Locate and cut a 6 3/4” square opening through wall.
3.Attach furnace to wall (see Attaching Furnace to Wall).
4.With furnace in place, after checking alignment of side outlet
opening in wall and furnace, place the 9 3/8” x 9 3/8” side outlet
wall plate over outer boot, pass the outer boot through the wall
and attach side wall plate to furnace side of wall with two (2)
10 x 1 1/2” provided screws.
5.Attach outer boot to the cabinet side with four (4) 8 x 1/4”
provided screws.
6.Position and attach inner boot to inner shield with four (4) 8 x
1/4” provided screws.
7.Place the register over the 6 3/4” square opening with the louvers positioned for the desired discharge direction and mark the
mounting holes using the register as a template.
13119-10-0709
Figure 5
4” MINIMUM TO COMBUSTIBLE
WALL OR SURFACE
4” MINIMUM TO COMBUSTIBLE
WALL OR SURFACE
VENT
TERMINAL
18” MIN. CLEARANCE TO
WALL OR COMBUSTIBLE
SURFACE USING MODEL
SOR-1 SIDE REGISTER
CLEARANCE FOR SIDE OUTLET KITS TO ADJACENT WALL
UNIT CANNOT BE RECESSED
WHEN SIDE REGISTERS ARE
USED.
5 ½”
5 ½”
12”
WHEN SIDE REGISTERS ARE
NOT USED, UNIT MAY BE RECESSED
UP TO 9 1/2”
Figure 6
Page 9
Locating Electric Supply
A 7/8” diameter knockout is provided at the bottom of the left
and right side panels. A three-prong (grounding) plug assembly is
located within the control compartment (bottom) of the furnace.
Please remove 7/8” knockout from appropriate side panel when
routing plug assembly to an electrical outlet. Unit can be hard wired
when recessed. Remove the 3 prong plug assembly and terminate
inside the unit junction box.
Figure 8
Figure 7
Installation of Three-prong (Grounding) Plug Assembly
1. Disconnect nylon cap on 3’ plug assembly from nylon plug
on wiring harness. Remove 3’ plug assembly from control
compartment (bottom) of the furnace.
2. Remove 7/8” knockout from appropriate side panel.
3. Insert nylon cap on 3’ plug assembly into the 7/8” hole in the
side panel.
4. Connect nylon cap on 3’ plug assembly to nylon plug on the
wiring harness.
5. Place 7/8” strain relief bushing around the cord of the 3’ plug
assembly. Insert 7/8” strain relief bushing into the 7/8” hole in
the side panel.
Attention! The 7/8” strain relief bushing is located within the same
envelope as the Installation Instructions and Owner’s Manual.
Attaching Furnace to Wall
Place collar on four inch flue tube against outlet box. Align clearance
holes on collar with screw holes in outlet box. Attach four inch flue
tube to outlet box with four (4) 10 x 1/2” screws.
Using Plastic Expansion Anchors
1. After locating mounting holes, drill two (2) 5/16” diameter
holes into the wall.
2. Insert two (2) plastic expansion anchors provided into the
holes.
3. Tighten two (2) 10 x 1” screws provided into the plastic
expansion anchors. (See Figure 9)
Attention: Do not overtighten screws because outlet box must be
able to move as flue tube expands and contracts.
Place collar on six inch air tube against air drop. Align clearance
holes on collar with screw holes in air drop. Attach six inch air tube
to air drop with eight (8) 10 x 1/2” screws.
Refer to Figure 5 for the location of the 7 1/2” diameter wall opening for the furnace. After the wall opening has been located and
cut, position flue outlet on furnace in center of wall opening. Insert
tubes through wall opening. When attaching furnace to the wall
remove that portion of baseboard and molding on the wall which is
behind the furnace. Attach furnace to wall, at the outer casing top,
with two (2) plastic expansion anchors provided and to floor, at the
outer casing bottom, with two (2) 10 x 1 1/2” screws provided.
Page 10
Figure 9
Attention! The screw holes on the outer casing bottom are off-set
the floor approximately 3/8”. Do not over-tighten screws and distort the off-set on the outer casing bottom. Distortion of the outer
casing bottom will not allow the lower front panel to be attached
to the furnace.
Installing Vent Assembly
Attention: Do not attempt to cut vent tubes. When you order
13119-10-0709
INSTALLATION INSTRUCTIONS (continued)
appropriate vent kit for measured wall depth the vent tubes will
fit together.
1. Place caulking (not provided) beneath the collar of the outside
mounting plate. Use additional caulking to correct uneven wall
surface, such as clapboard.
2. Insert six inch air tube on outside mounting plate INTO six
inch air tube attached to air drop. Place four inch flue tube
on vent cap OVER four inch flue tube attached to outlet box.
Position the outside mounting plate so that six inch air tube
has a slight downward slope to the outside. The downward
slope is necessary to prevent the entry of rainwater. Attach
outside mounting plate to exterior wall with four (4) 10 x 1 1/2”
screws.
3. Installation is completed.
Reassembly And Resealing Vent-Air Intake System
When vent-air intake system is removed for servicing the furnace,
the following steps will assure proper reassembly and resealing of
the vent-air intake assembly.
1. Remove old caulking beneath the collar of the outside mounting
plate. Apply new caulking beneath the collar of the outside
mounting plate. Use additional caulking to correct uneven wall
surface, such as clapboard.
2. Insert six inch air tube on outside mounting plate into six
inch air tube attached to air drop. Position the outside mounting
plate so that six inch air tube has a slight downward slope to
the outside. The downward slope is necessary to prevent the
entry of rainwater. Attach outside mounting plate to exterior
wall with four (4) 10 x 1 1/2” screws.
3. Place four inch flue tube on vent cap over four inch flue tube
attached to outlet box. Attach vent cap to outside mounting plate
with three (3) 10 x 1/2” screws.
4. Reassembly and resealing vent-air intake system is
completed.
Direct vent furnaces are designed to be installed on a uniform
outside wall. When the wind comes from any angle (up, down or
from either side), it must hit the vent cap equally over both the air
inlet and the flue outlet portions of the vent. Any wall projection,
such as a door or window casing, which disturbs the wind on one
side of the air inlet section will result in back pressure on the flue
section smothering the flame and eventual pilot outage.
When the vent cap is to be installed on siding or it appears that a
projection within 6” of any side of the air inlet section could shield
the air inlet section, the entire vent should be supported away from
the wall at least the distance of the projection. 2” x 4” framing
whose outside dimensions match the overall dimensions of the
mounting plate is recommended. The 2” x 4” framing protects
siding from possible warpage or discoloration. All joints can then
be sealed and painted. The wall depth plus the additional depth
of the 2” x 4” framing should not exceed a total depth of 14” for
DVC-35T. (See Figure 10)
Vinyl siding vent kit, DV-822, is available from Empire Comfort
Systems, Inc. The depth is 3”, which enables the vent cap to be
extended away from siding or projections. The wall depth plus the
additional 3” depth of the vinyl siding vent cap extension should
not exceed a total depth of 19” for DVC-35T. (See Figure 11)
Warning: When vinyl siding vent kit, DV-822 or 2” x 4”
framing is added to an existing installation (furnace is
installed) do not attempt to add sections of pipe to the flue
outlet tube or air inlet tube. An air tight seal is required for
both tubes. Refer to Parts List, page 16 to order tubes.
Installing a Vent Near a Window Ledge,
Other Type of Projection or on Siding (vinyl, aluminum, etc.)
Figure 10
13119-10-0709
Figure 11
Page 11
DVC-35T STANDING PILOT LIGHTING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
Warning: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these instructions
exactly.
B. Before lighting smell all around the appliance
area for gas. Be sure to smell next to the floor because
some gas is heavier than air and will settle on the floor.
What To Do If You Smell Gas
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or turn
by hand, don’t try to repair it; call a qualified service
technician. Force or attempted repair may result in a fire
or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
Lighting Instructions
1. Stop! Read the safety information above.
2. Set the thermostat to lowest setting.
3. Turn off all electric power to the appliance.
4. Remove control access panel (lower front panel).
5. Turn gas control knob clockwise
control. The pilot is located between the two burner tubes
behind the pilot access cover.
9. Turn gas control knob counterclockwise
to
“PILOT.”
10. Push and hold red reset button down completely and
repeatedly push the ignitor button until the pilot burner
is lit. Pilot may also be lit with a match. Continue to
hold the red reset button down for about one (1) minute
after the pilot is lit. Release button and it will pop back
up. Pilot should remain lit. If it goes out, repeat steps 5
through 10.
•
If button does not pop up when released, stop and
immediately call a qualified service technician or gas
supplier.
•
If the pilot will not stay lit after several tries, turn
the gas control knob to “OFF” and call your service
technician or gas supplier.
to “OFF.”
6. Wait ten (10) minutes to clear out any gas. Then smell
for gas, including near the floor. If you smell gas, STOP!
Follow “B” in the safety information above. If you don’t
smell gas, go to the next step.
7. Remove the pilot access cover located on
the combustion chamber.
11. Replace pilot access cover.
to
12. Turn gas control knob counterclockwise
“ON.”
13. Replace control access panel (lower front panel).
14. Turn on all electric power to the appliance.
8. Find pilot - follow
metal tube from gas
15. Set thermostat to desired setting.
To Turn Off Gas To Appliance
1. Set the thermostat to lowest setting.
2. Turn off all electric power to appliance if service is to be
performed .
3. Remove control access panel (lower front panel).
Page 12
4. Push in gas control knob slightly and turn clockwise
to “OFF.” Do not force.
5. Replace control access panel (lower front panel).
13119-10-0709
DVC-35IPT INTERMITTENT PILOT LIGHTING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE OPERATING
Warning: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
A. This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand.
B. Before OPERATING smell all around the appliance
area for gas. Be sure to smell next to the floor because
some gas is heavier than air and will settle on the floor.
What To Do If You Smell Gas
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
•
If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to slide the gas control knob. Never
use tools. Force or attempted repair may result in a fire
or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
OPERATING Instructions
1. Stop! Read the safety information above.
5. Remove front panel door.
2. Set the thermostat to lowest setting.
6. Slide gas control switch to “OFF.”
3. Turn off all electric power to the appliance.
7. Wait ten (10) minutes to clear out any gas. Then smell
for gas, including near the floor. If you smell gas, STOP!
Follow “B” in the safety information above. If you don’t
smell gas, go to the next step.
4. This appliance is equipped with an ignition device which
automatically lights the pilot. Do not try to light the pilot
by hand.
8. Slide gas control switch to “ON”.
9. Replace front panel door.
CONTROL
OFF
ON
GAS FLOW
IGNITOR
10. Turn on all electric power to the appliance.
11. Set thermostat to desired setting.
12. If the appliance will not operate, follow the instructions
“TO TURN OFF GAS TO APPLIANCE” and call your
service technician or gas supplier.
GAS VALVE SHOWN IN OFF POSITION
HONEYWELL IP SMART VALVE
To Turn Off Gas To Appliance
1. Set the thermostat to lowest setting.
3. Remove front panel door.
2. Turn off all electric power to the appliance
if service is to be performed.
4. Slide gas control switch to “OFF.”
13119-10-0709
5. Replace front panel door.
Page 13
PILOT FLAME CHARACTERISTICS
The correct pilot flame (Figure 12) will be blue, extending past
the thermocouple. The flame will surround the thermocouple just
below the tip.
Natural gas pilots require adjusting when the inlet gas pressure is
above 5” w.c. (1.245kPa). Remove the pilot cover screw on the
control valve (Figure 3), and turn the adjustment screw clockwise
to reduce flame. Replace pilot cover screw to eliminate gas leaking
at that control valve opening.
LP gas (propane) will not require adjustment.
THERMOCOUPLE
BURNER
SPARK
ELECTRODE
PILOT
After use, cleaning may be required for the proper flame.
STANDING PILOT
IP-Model Pilot
This heater is using a Honeywell “Smart Valve” system for
intermittent pilot ignition.
On a call for heat by the thermostat this control turns on a 24 volt
mini hot surface ignitor which lights a pilot that in turn lights the
main burner. The gas valve used in this system is a step opening
which opens at a lower pressure for ignition and then steps to a
full inlet pressure of 4” pressure on Natural gas and 10” pressure
on LP gas.
THERMOCOUPLE
PILOT SHIELD
SPARK
ELECTRODE
Pilot Flame Adjustment
The pilot flame should envelop 3/8 to 1/2 inch (10 to 13mm) of the
tip of the flame rod. See Figure 12.
To adjust:
1. Remove the pilot adjustment cover screw.
2. Turn the inner adjustment screw clockwise
to decrease
or counterclockwise
to increase pilot flame. Pilot adjustment is shipped at full flow rate. Turn the inner adjustment
screw clockwise
if the inlet pressure is too high.
3. Replace the cover screw after the adjustment to prevent gas
leakage.
PILOT LOCATION END VIEW
STANDING PILOT SHOWN
3/8” TO 1/2”
PILOT FLAME
GROUND
ELECTRODE
BURNER
PILOT
HOT SURFACE
IGNITOR
FLAME
ROD
IP-MODEL PILOT
Figure 12
Page 14
13119-10-0709
MAIN BURNER FLAME CHARACTERISTICS
The correct flame will be a short, blue inner flame with a much
larger, light blue, outer flame. The burner does not have a primary
air adjustment. The flame will be correct if the factory-set pressure
and orifice opening are used. After the furnace has been operating,
the burner ports may be blocked by foreign matter carried in by
combustion air. Therefore, cleaning of the burner may be needed
for proper flame.
To clean burner port disconnect the gas supply to the valve, and
remove the screws fastening the burner door. After removing the
burner door from the burner box, remove each main burner. Pilot
mounting bracket will need to be unscrewed and moved out of the
way to remove all burners. Burners can be blown out using compressed air or by blowing through them. Be sure there is no lint
or foreign debris blocking the burner ports. Reassemble using the
same screws earlier removed and locate pilot in the same position
as before and noted above.
Figure 13
WIRING
The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70 or Canadian Electrical
Code, CSA C22.1, if an external electrical source is utilized. This
appliance is equipped with a three-prong [grounding] plug for
your protection against shock hazard and should be plugged
directly into a properly grounded three-prong receptacle. Do
not cut or remove the grounding prong from this plug. For an
ungrounded receptacle, an adapter, which has two prongs and a
wire for grounding, can be purchased, plugged into the ungrounded
receptacle and its wire connected to the receptacle mounting screw.
With this wire completing the ground, the appliance cord plug can
be plugged into the adapter and be electrically grounded. A 7/8”
hole is provided in the junction box for use with a conduit connector
if local codes require this type of protection.
DVC-35T
DVC-35IPT
Thermostat Installation
The thermostat should be installed in the same room as the furnace
4’ to 5’ above the floor and away from another heat source (cooking
stove, hot water heater, etc.) including walls and doorways with
a heat source in an adjoining room. Do Not Install Thermostat
on Outside Wall.
CAUTION: Label all wires prior to disconnection when
servicing controls. Wiring errors can cause improper and
dangerous operation. Verify proper operation after servicing.
13119-10-0709
Figure 14
Page 15
PRESSURE REGULATOR
ADJUSTMENT-UNDER CAP
SCREW
OUTLET PRESSURE TAP
PILOT OUTLET
ON
CONTROL
GASFLOW
OFF
PILOT ADJUSTMENTUNDER CAP SCREW
IGNITOR
INLET PRESSURE
TAB
CONTROL
IGNITOR
IGNITOR-PILOT ASSY.
WIRING
TO 24 V THERMOSTAT
TO 24 V COMMON ON TRANSFORMER
TO 24V."HOT" ON TRANSFORMER
L2 NEUTRAL
1 P-MODEL GAS VALVE AND WIRING
120 VAC
L1 "HOT"
FAN
SWITCH
MOTOR
120 VAC
40 VA TRANSFORMER
24 VAC
VALVE CONTROL
CONNECTOR
LIMIT
CONTROL
Figure 15
THERMOSTAT
HONEYWELL IP
SMART VALVE
VENT SAFETY
LIMIT
LADDER WIRING DIAGRAM-IP VALVE
Figure 16
Page 16
13119-10-0709
SERVICE AND MAINTENANCE SUGGESTIONS
General: All furnaces have been fire-tested to check for proper
operation. This includes, main burner flame, pilot flame, fan
operation, fan control, limit control and automatic valve operation.
If the furnace fails to function on initial installation, it is advisable
to re-check the following:
1. 115 volts to the junction box.
2. Inlet gas pressure.
3. The 24 volt system.
4. Type of gas being used and that shown on the rating label.
The Service Department at Empire Comfort Systems, Inc. may
be contacted to assist in servicing furnace or a call a qualified
serviceman.
Standing Pilot Model
Servicing the Pilot and Main Burners, Pilot Orifice,
Thermocouple, and Main Burner Orifices: Disconnect the gas
supply at the inlet to the control valve. Then remove the burner
door to gain access to the above listed components.
Spark Igniter Does Not Light Pilot: With air in the gas line, such
as when the furnace is first installed or was off all summer, the
pilot flame may be too lean to ignite on the first few trials. Turn
the control valve knob to pilot position and depress the red reset
button. Holding the button down continually to bleed the line;
1. Use lighter rod to light pilot with a match.
2. Use the piezo ignitor at 30 second intervals until it lights.
If Electrode Does Not Produce Spark:
1. Check wire connections.
2. Check gap for pilot burner to the electrode tip. Should be
between 1/8” and 3/16”. Electrode wire and tip must be
more than 1/4” away from all other metal components.
If Pilot Does Not Light By Any Means:
1. Check valve knob for being in the “Pilot” position.
2. Check pilot adjustment for being full open (counterclockwise
to open).
3. If gas is available in the supply tubing, the pilot orifice and/or
pilot burner is probably restricted by a spider web. Clean
pilot assembly and relight.
13119-10-0709
If Pilot Does Not Remain On After Releasing Knob:
1. Follow instructions and hold button down longer and
harder.
2. Determine if pilot flame extends past thermocouple; if not,
adjust input or clean pilot burner.
3. Replace thermocouple if millivolts read less than 15
millivolts.
Pilot Outage During Normal Operation:
1. Check air inlet tube for a good fit.
2. Check burner door and pilot hole cover for tight seal.
3. Check input by manifold pressure gauge or gas meter.
Main Gas Valve Does Not Open When Thermostat Is Turned
To On:
1. Check for 24 volts to valve by removing one wire and
touching to the same terminal it was on. Terminal
should have a light spark. Do not short across
terminals, as it will burn out the wall
thermostat.
2. Thermostat wires at the wall may be shorted, so check for
a faulty thermostat.
3. To check for line voltage to furnace, remove front panel and
short across two-terminal fan control to allow fan to operate.
(Figure 15)
Cleaning Combustion (Exchanger) Assembly
A Qualified Service Person should remove the combustion
(exchanger) assembly and flue baffles. Apply air pressure to the
inside of the combustion (exchanger) assembly and flue baffles in
order to clear all passageways.
Oiling the Motor
The fan motor should be cleaned and oiled once each heating
season. Oil holes are located on the top at each end of the motor.
Use a few drops of #10 motor oil. To clean the motor, blow air
through its ventilation openings with a vacuum cleaner or low
pressure air source.
Page 17
DVC-35IPT INTERMITTENT PILOT SEQUENCE OF OPERATION
Apply 24 VAC
To Appliance
START
Thermostat
Calls for Heat
5 Minute Retry Delay
Flame Signal
Detected
YES
Pilot Valve Ignition OFF
Wait for Flame Signal to
Disappear


NO
System Check
Internal Check
OK
NO
YES
Trial for
Ignition


Pilot Valve Opens
Ignitor Powered
Pilot Light and Flame is
Sensed During Trial For
Ignition (1)
NO


Pilot Valve Closes
Ignition OFF
YES
Main Burner
Operation


3 Second Flame Recycle
Delay
Ignitor OFF
Main Valve Opens
Flame Signal
Lost?
YES
Main Pilot
Valves Close
NO
Thermostat Call for Heat
Ends
Flame Lost More
Than 5 Times in
One Call for Heat
NO
END
Main Pilot Valves
Close
YES
(1) Ignitor will turn OFF about 30 seconds into the trial for ignition if the pilot flame has not lit. It will turn back ON for the final 30 seconds of
the 90 second trial for ignition. The pilot will be energized during the entire trial for ignition. This is normal operation for this gas ignition
system.
Page 18
13119-10-0709
DVC-35IPT INTERMITTENT PILOT SYSTEM TROUBLESHOOTING SEQUENCE
START
Turn OFF Gas Supply
Disconnect System Control
Harness
Set Thermostat to Call for
Heat
Check for Proper Voltage at
Control Harness (See Inset A Voltage Should be 24V
Between Thermostat and 24V
Common, and 24V Between
24V Common and 24V Hot.)
IP SYSTEM TROUBLESHOOTING SEQUENCE
TM
SmartValve System Troubleshooting Sequence
Note: Before Troubleshooting, Become Familiar
with the Sequence of Operation
NO
YES
Plug Harness into SmartValve
Control
Wait for Internal Check Delay
(SV9501)
Igniter Warms UP and Glows
Red
NO
INSET B
NO
End View
of Control
Harness
Connector
EFT
Output
24
Volts
24 Volt
Hot
HSI
Terminals
Replace SmartValve Control
Reconnect Pilot Burner Cable
Replace Igniter/Flame Rod
Assembly
Note: Igniter Will Cycle OFF
and Back ON Once During the
90 Second Ignition Trial
Reconnect Pilot Burner Cable
YES
Turn On Gas Supply
Pilot Burner Lights
Line Voltage Power
Low Voltage Transformer
Limit Controller
Thermostat
Wiring
INSET A
24
Volts
24 Volt
Common
Check
Unplug Pilot Burner Cable.
Measure Voltage at SmartValue HSI
Element Output (See Inset B) 24V
Nominal
24 Volt
Thermostat
NO
Check that Pilot Gas is Flowing
Wait to Assure Pilot Gas Tubing is
Purged.
Measure Voltage Between 24V Hot
and 24V Common Leads to
SmartValve Control. Must Measure
at Least 19.5 VAC with Igniter
Powered. See Inset A to Identify
Proper Lead. This Check Must be
Done with the SmartValve Control
Connected and Igniter Powered.
YES
NO
NO
Replace SmartValve Control
Check Transformer and Line Volt
Supply
Replace Igniter/Flame Rod
Assembly
Main Valve Opens and
Main Burner Lights
YES
System is Okay
13119-10-0709
NO
Check that Pilot Flame Makes
Good Contact with Pilot Burner
Flame Rod
Check for Good Electrical
Connection Through the Pilot
Tubing
If Both of the Above are Good,
Replace Igniter/Flame Rod
Cycle Thermostat OFF and Back
ON
Main Burner Lights
NO
Replace SmartValve Control
Page 19
HOW TO ORDER REPAIR PARTS
Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts through
the distributor. Parts can be shipped directly to the service person/dealer.
All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your
equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the following appropriate
illustration and list. Be sure to give all this information.
Part Description
Furnace Model Number
Furnace Serial Number
Part Number
Type of Gas (Propane or Natural)
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
Shipments contingent upon strikes, fires and all causes beyond our control.
Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, IL 62222-0529
PARTS LIST
PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.
Index
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
26
27
27
28
29
30
31
31
32
32
32
32
33
34
35
36
37
38
Part
Number
Description
DV-1213
TOP PLATE
R-3165
DOOR CLIP (2 REQUIRED)
DV-1204
CASING SIDE - RIGHT
DV-1202
CASING BACK
DV-1205
CASING SIDE - LEFT
DV-1249AIR DROP
DV-1230
TURBULATOR (3 REQUIRED)
13213
OUTLET BOX REAR
13217
OUTLET BOX COVER
R-3161
FAN BLADE
R-3166
FAN MOTOR
DV-1246
MOTOR MOUNTING BRACKET
R-1536
BUSHING (4 REQUIRED)
R-1499
RUBBER GROMMET (4 REQUIRED)
R-1454
BRASS BUSHING (4 REQUIRED)
R-3164
DOOR CLIP (2 REQUIRED)
DV-1251
INNER SHIELD - RIGHT (INCLUDES
NO. 22)
R-6176
FAN CONTROL SWITCH
R-3175
LIMIT SWITCH
DV-1255
INNER SHIELD FRONT
DV-1253
INNER SHIELD COVER PLATE (2
REQUIRED)
DV-1252
INNER SHIELD -LEFT (INCLUDES
NO. 22)
13211EXCHANGER ASSEMBLY
R-3162
FILTER
R-3163
FILTER RETAINER
R-3232
PILOT - NAT (IP ONLY)
R-3233
PILOT - LPG (IP ONLY)
P-88-52
ORIFICE - NAT (3 REQUIRED)
P-88-60
ORIFICE - LPG (3 REQUIRED)
DV-1236
MANIFOLD
DV-1259
FRONT PANEL
P-112
MANIFOLD UNION
R-1109
BUSHING (3/8 X 1/2)
R-9505
BUSHING (1/2 X 3/4) - NAT (IP ONLY)
R-3170
GAS VALVE - NAT (IP ONLY)
R-3171
GAS VALVE - LPG (IP ONLY)
R-2148
GAS VALVE - NAT (SPP ONLY)
R-5655
GAS VALVE - LPG (SPP ONLY)
R-2708
PIEZO IGNITOR (SPP ONLY)
DV-781
OBSERVATION HOLE COVER ASSEMBLY
M-155
GASKET
FF-160
PIEZO BRACKET (SPP ONLY)
DV-1240
BURNER COMPARTMENT FRONT
DV-1265
BURNER COMPARTMENT BODY
Index
No.
Part
Number
M-156
DV-775
DV-691
M-148
DV-1235
R-3031
DV-1239
UH-810
39
40
40
41
42
43
44
45
45
UH-452
R-1995
R-998
UH-451
DV-572
R-1410
R-690
R-1515
DV-1215
R-3034
R-3035
GWT-021
R-3180
46
46
47
48
49
50
51
52
53
53
54
55
56
57
58
R-2256
R-6389
13057
59
60
M-177
13104
61
13062
62
63
64
65
66
NOT SHOWN
NOT SHOWN
NOT SHOWN
NOT SHOWN
NOT SHOWN
NOT SHOWN
NOT SHOWN
NOT SHOWN
NOT SHOWN
M-178
13106
13064
13059
13053
DV-1261
R-1081
R-1089
R-1233
R-3265
R-3172
R-3173
R-3236
DV-1264
Description
GASKET
SEAL BRACKET (SPP ONLY)
SEAL BRACKET (IP ONLY)
MANIFOLD GASKET
PILOT BRACKET (IP ONLY)
BURNER (3 REQUIRED)
BURNER BRACKET
TRANSFORMER MOUNTING BRACKET
(SPP ONLY)
TRANSFORMER MOUNTING BRACKET (IP
ONLY)
TRANSFORMER (SPP ONLY)
TRANSFORMER (IP ONLY)
JUNCTION BOX COVER
JUNCTION BOX
BUSHING
CORD SET
BUSHING
BOTTOM PLATE
PILOT - NAT (SPP ONLY)
PILOT - LPG (SPP ONLY)
PILOT BRACKET (SPP ONLY)
ELECTRODE AND WIRE ASSEMBLY (SPP
ONLY)
THERMOCOUPLE -18” (SPP ONLY)
WALL THERMOSTAT - 24 VOLT
OUTLET TUBE - INNER ASSEMBLY (INCLUDES 59 & 60)
GASKET - OUTER COLLAR
OUTLET TUBE - INNER WELDED ASSEMBLY
INLET TUBE - INNER ASSEMBLY (INCLUDES 62 & 63)
GASKET - INLET COLLAR
INLET TUBE - INNER WELDED ASSEMBLY
INLET TUBE - OUTER ASSEMBLY
OUTLET TUBE - OUTER ASSEMBLY
VENT CAP WELDED ASSEMBLY
PILOT TUBING
PILOT ORIFICE - NAT (SPP ONLY)
PILOT ORIFICE - LPG (SPP ONLY)
PILOT ORIFICE - NAT (IP ONLY)
PILOT ORIFICE - LPG (IP ONLY)
WIRE HARNESS (SPP ONLY)
WIRE HARNESS (IP ONLY)
WIRE (IP ONLY)
HARDWARE PACKAGE
Use Only Manufacturer’s Replacement Parts. Use of Any Other Parts Could Cause Injury Or Death.
Page 20
13119-10-0709
PARTS VIEW
13119-10-0709
Page 21
SERVICE NOTES
Page 22
13119-10-0709
SERVICE NOTES
13119-10-0709
Page 23
EMPIRE
Comfort Systems
Empire Comfort Systems Inc.
918 Freeburg Ave. Belleville, IL 62220
If you have a general question about our products, please e-mail us at
info@empirecomfort.com.
If you have a service or repair question, please contact your dealer.
www.empirecomfort.com
Page 24
13119-10-0709
Download PDF