Chauvet | Intimidator Wash Zoom 350 IRC | User manual | Chauvet Intimidator Wash Zoom 350 IRC User manual

User Manual
TABLE OF CONTENTS
1. Before You Begin ......................................................................................................................... 4
What is Included ............................................................................................................................................................. 4
Unpacking Instructions .................................................................................................................................................... 4
Claims ............................................................................................................................................................................. 4
Text Conventions ............................................................................................................................................................ 4
Symbols .......................................................................................................................................................................... 4
Disclaimer ....................................................................................................................................................................... 4
Product at a Glance ........................................................................................................................................................ 5
Safety Notes.................................................................................................................................................................... 5
2. Introduction .................................................................................................................................. 6
Overview ......................................................................................................................................................................... 6
Dimensions ..................................................................................................................................................................... 7
3. Setup ............................................................................................................................................. 8
AC Power ........................................................................................................................................................................ 8
Fuse Replacement .......................................................................................................................................................... 8
Power Linking.................................................................................................................................................................. 9
Power Linking Diagram .............................................................................................................................................. 9
Mounting ....................................................................................................................................................................... 10
Orientation..................................................................................................................................................................... 10
Rigging .......................................................................................................................................................................... 10
Rigging Diagram ...................................................................................................................................................... 10
4. Operation .................................................................................................................................... 11
Control Panel Descrioption ........................................................................................................................................... 11
Menu Map ................................................................................................................................................................ 11
Zone Control ................................................................................................................................................................. 12
Zone Control Drawing .............................................................................................................................................. 12
Configuration (DMX) ..................................................................................................................................................... 13
DMX Starting Address ............................................................................................................................................. 13
DMX Personalities ................................................................................................................................................... 13
DMX Channel Assignments and Values .................................................................................................................. 14
29-CH ................................................................................................................................................................. 14
14-CH ................................................................................................................................................................. 18
Configuration (Standalone) ........................................................................................................................................... 21
Sound Mode ............................................................................................................................................................ 21
Auto Mode................................................................................................................................................................ 21
IR Mode ................................................................................................................................................................... 22
IRC-6 Operation ................................................................................................................................................. 22
Configuration (Master/Slave) ........................................................................................................................................ 23
Configuring the Slaves ............................................................................................................................................. 23
Configuring the Master ............................................................................................................................................ 23
Configuration (Settings) ................................................................................................................................................ 24
Pan Reverse ............................................................................................................................................................ 24
Tilt Reverse .............................................................................................................................................................. 24
Pan Range ............................................................................................................................................................... 24
Tilt Range................................................................................................................................................................. 24
Movement Speed ..................................................................................................................................................... 25
Fan Operation .......................................................................................................................................................... 25
Display ON/OFF ...................................................................................................................................................... 25
Display Orientation .................................................................................................................................................. 26
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 2 of 31
Dimming Curve ........................................................................................................................................................ 26
Dimming Speed ....................................................................................................................................................... 26
Color Balance .......................................................................................................................................................... 26
Sensitivity ................................................................................................................................................................. 27
Reset........................................................................................................................................................................ 27
Reset to Factory Defaults ........................................................................................................................................ 27
System Information ....................................................................................................................................................... 27
5. Technical Information ................................................................................................................ 28
Product Maintenance .................................................................................................................................................... 28
6. Technical Specifications ........................................................................................................... 29
Returns ........................................................................................................................................... 30
General Info .................................................................................................................................................................. 30
U.S., UK, Ireland, and Mexico....................................................................................................................................... 30
Contact Us ...................................................................................................................................... 31
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 3 of 31
1. BEFORE YOU BEGIN
What is
Included
Unpacking
Instructions
Claims
Text
Conventions
· Intimidator™ Wash Zoom 350 IRC
· Power Cord
· Thread Reducing Adapter
Carefully unpack the product immediately and check that all the parts are in the package and
are in good condition.
If the box or any of the contents appear damaged from shipping, or show signs of mishandling,
save all packaging and file a claim with the carrier immediately, do not notify CHAUVET®.
Failure to report damage to the carrier immediately or failure to have all packaging available for
inspection may invalidate your claim.
For other issues, such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with CHAUVET® within 7 days of delivery. For information on
contacting CHAUVET®, see the Contact Us section of this manual.
Convention
Meaning
1–512
A range of values
50/60
A set of values
Settings
A menu option
Menu > Settings
<ENTER>
ON
Symbols
· Warranty Card
· Quick Reference Guide
A sequence of menu options
A button to be pressed
A value to be entered or selected
Symbol
Meaning
Critical installation, configuration, or operation information. Not following
these instructions can make the product not work, cause damage to the
product, or cause harm to the operator.
Important installation or configuration information. The product might
not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this User Manual are subject to change without
notice. CHAUVET® assumes no responsibility or liability for any errors or omissions, and
reserves the right to revise or recreate this manual at any time. The latest version of this
manual should be downloaded from http://www.chauvetlighting.com/product-manuals-literature/.
© Copyright 2014 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Author
Date
Editor
Date
L. Henry
2/11/13
A. Leon
2/17/14
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 4 of 31
Product at a
Glance
Use on Dimmer
Outdoor Use
Sound-Activated
DMX
Master/Slave
Safety Notes
x
x
P
P
P
Auto Programs
Auto-ranging Power Supply
Replaceable Fuse
User-Serviceable
P
P
P
x
These notes include important information about the mounting, use, and maintenance of this
product. Read these notes before using the product.
· Always connect the product to a grounded circuit to avoid the risk of electrocution.
· Make sure the power cord is not crimped or damaged.
· Always disconnect the product from the power source before cleaning it or replacing the
fuse.
· Never disconnect the product from the power source by pulling or tugging on the cord.
· If mounting the product overhead, always secure it using a safety cable.
· Make sure there are no flammable materials close to the product when it is operating.
· Avoid direct eye exposure to the light source while the product is on.
· Do not touch the product’s housing when the product is operating because the housing can
be very hot.
·
·
·
·
·
·
·
·
·
·
·
·
·
This product is not intended for permanent installation.
The product is for indoor use only! It is rated at IP20.
To prevent risk of fire or shock, do not expose the product to rain or moisture.
Always make sure that the voltage of the power source to which the product is connected is
within the range stated on the sticker or rear panel of the product.
Never connect the product to a dimmer or rheostat.
Make sure to replace the fuse with another of the same type and rating.
Always install the product in a location with adequate ventilation, and leave at least 20 in
(50 cm) between the product and adjacent surfaces.
Always use the handles to carry this product.
The maximum ambient temperature (Ta) in which the product can be used is
104 °F (40 °C). Do not operate the product at higher temperatures.
Be sure that no ventilation slots on the product’s housing are blocked.
Never carry the product by the power cord or any moving part.
In the event of a serious operating problem, stop using the product immediately.
Never try to repair the product. Repairs carried out by unskilled people can lead to damage
or malfunction. Contact the nearest authorized technical assistance center.
· Keep this User Manual for future reference. If you sell the product to another user, be sure
to give this manual to the next owner.
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 5 of 31
2. INTRODUCTION
Overview
Yoke
Handles
Ventilation Fans
IR Sensor
Indicator
Light
LCD
Display
Control
Buttons
DMX In
Fuse
Holder
Power In
DMX Out
Back Panel View
Power Out
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 6 of 31
Dimensions
10.6 in
270 mm
14.3 in
363 mm
7.6 in
194 mm
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 7 of 31
3. SETUP
AC Power
The Intimidator™ Wash Zoom 350 IRC has an auto-ranging power supply that works with an
input voltage range of 100 to 240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use
the values listed on the label affixed to the product’s back panel, or refer to the product’s
Specifications. The listed current rating indicates the product’s average current draw under
normal conditions.
The Intimidator™ Wash Zoom 350 IRC can be power linked via the IEC and Edison outlets in
its base.
Always connect the product to a protected circuit (circuit breaker or fuse). Make sure
circuit has an appropriate electrical ground to avoid the risk of electrocution or fire.
Never connect the product to a rheostat (variable resistor) or dimmer, even if the
rheostat or dimmer serves only as a 0 to 100% switch.
Fuse
Replacement
Make sure product is not connected to a power source.
1. Place the tip of a flat-head screwdriver into the slot in the fuse holder.
2. Turn the screwdriver counterclockwise and the fuse holder will come loose.
3. Pull the fuse holder out of the product.
4. Pull the blown fuse out of the fuse holder.
5. Place a new fuse of the exact same type and rating into the fuse holder.
6. Insert the fuse holder into the product.
7. Place the tip of a flat-head screwdriver into the slot in the fuse holder.
8. Turn the screwdriver clockwise and the fuse holder will tighten into place.
Disconnect the product from power before replacing the fuse.
Use only the fuse listed in the Technical Specifications section or on the specifications
sticker on the product.
A spare fuse is not included.
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 8 of 31
Power Linking
The product provides power linking via the Edison/IEC outlet located in the back of the unit.
st
1
Product
Power Linking
Diagram
nd
2
Product
rd
3
Product
Additional Products
Up to 5 Intimidator™ Wash Zoom 350 IRC units can be linked on 120 V, or up to
12 Intimidator™ Wash Zoom 350 IRC units on 230 V.
The power linking diagram shown above corresponds to the North American version of
the product ONLY!
If using this product anywhere other than North America, consult with the local
CHAUVET® distributor because power linking connectors and requirements differ from
country to country, and region to region.
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 9 of 31
Mounting
Before mounting the product, read and follow the safety recommendations in the Safety Notes
section.
Orientation
The Intimidator™ Wash Zoom 350 IRC can be mounted in any position, but make sure the
placement allows adequate ventilation for the product, and allows for movement of the yoke
and head in any direction.
Rigging
Be sure to place the product in a location that allows easy access to it for maintenance and
programming, and enough space around the product for ventilation.
Make sure that the structure or surface onto which the product will be mounted can support the
product’s weight. For more information see the Technical Specifications section.
When mounting the product overhead, always use a safety cable and make sure the product is
attached securely.
When mounting the product on a truss or pipe, use a mounting clamp with the appropriate
weight capacity. CHAUVET® has a full range of mounting clamps. See
http://www.chauvetlighting.com/cables-clamps-main.html for the complete selection.
The rubber feet serve as floor supports. When placing the product on the floor, make sure that
the product and cables are away from people and vehicles.
The included Thread Reducing Adaptor changes the built-in threaded mounting hole
from M12 to M10 size. The smaller M10 size works with the CLP-10 clamp from
CHAUVET®.
When using only one mounting clamp, be sure to use a clamp with a captive bolt to
prevent accidental loosening.
Mounting Clamp
(such as CLP-15 from CHAUVET®)
Threaded Mounting Hole
size M12 on bottom panel
Safety Cable
(such as CH-05 from
CHAUVET®)
Secure the safety cable
using the pass-through on
the bottom of the product
Rigging Diagram
Handles on
both sides
Fan and Ventilation Slots
(ensure adequate space for
ventilation)
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 10 of 31
4. OPERATION
Control Panel
Descrioption
The control panel is used to set the operating mode, and the configuration settings of the
product. Use the 4 buttons underneath the LCD display to access the control panel and
navigate the menu map. For specific instructions see the Configurations sections below.
Button
Function
<MENU>
Enters into, or backs out of, the current menu option
<UP>
Scrolls up the list of options or selects a higher value
<DOWN>
Scrolls down the list of options or selects a lower value
<ENTER>
Activates a selected menu or value
Menu Map The Menu Map presents all the options in the menu system, and the values to set them.
Menu
Value
Description
Address
001–512
14CH
DMX
Run Mode
Sets the DMX starting address
29CH
Auto01—
Auto16
Auto
Sets Auto mode
Sound
Sets Sound mode
Slave
Sets Slave mode
IR
Pan Reverse
Tilt Reverse
Pan Angle
Setup
Sets DMX personality
Tilt Angle
Sets infrared control
OFF
Normal pan operation
ON
Reverse pan operation
OFF
Normal tilt operation
ON
Reverse tilt operation
540
Sets the 540° pan angle range
360
Sets the 360° pan angle range
180
Sets the 180° pan angle range
270
Sets the 270° tilt angle range
180
Sets the 180° tilt angle range
90
Sets the 90° tilt angle range
Normal
P/T Speed
Fast
Sets the panning/tilting speed
Slow
Fans
Display
Screen Rev
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Auto
Sets fan speed to be triggered
according to temperature
Full
Sets fan speed to full
OFF
Display turns off after inactivity
ON
Display stays on after inactivity
OFF
Normal display
Page 11 of 31
Menu
Value
Description
ON
Upside-down display
Square
I Squa
Dimmer
Curve
SCurve
Sets the dimmer curve mode
Linear
Setup (Cont.)
Fast
Dimmer
Speed
Smooth
Sets the dimmer speed
RED
GREEN
Color
Balance
BLUE
Sets color balance for white
(100–255)
WHITE
Sensitivity
001—100
Reset
Factory Set
Sys Info
Zone Control
Ver
Running Mode
DMX Address
Temperature
Sets sound sensitivity
Resets the product
Loads factory defaults
Shows the current software version,
running mode, DMX address and
product’s temperature
The Intimidator™ Wash Zoom 350 has 4 zones of control so that the light can emit different
individual colors and patterns of light. The most flexibility over zone control is in the
29-channel DMX personality, which has direct color control of the zones.
Both the 29-channel and 14-channel DMX personalities have macros that use the zones.
Zone Control
Drawing
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 12 of 31
Configuration
(DMX)
To set the product in DMX mode for control with a DMX controller, do the following:
1. Make sure the product is plugged into a power source.
2. Connect the male end of a DMX cable to the DMX out socket of the DMX controller and
the female end of the same cable to the DMX in socket on the product.
3. Set the DMX starting address and personality by following the directions below.
DMX Starting When selecting a starting DMX address, always consider the number of DMX channels
Address needed for the selected DMX personality. Choosing a starting address that is too high can
restrict access to some of the product’s channels.
The Intimidator™ Wash Zoom 350 IRC uses either 14 or 29 channels, depending on the
personality. The highest configurable DMX address in 14-channel mode is 499. The highest
configurable DMX address in 29-channel mode is 484.
For more information about DMX download the CHAUVET® DMX Primer from the
CHAUVET® web site http://www.chauvetlighting.com/download.
To set the DMX starting address, do the following:
1. If the display shows a number from 001–512, go to step 5.
2. Press <MENU> repeatedly until 4 icons show on the display.
3. Use <UP> or <DOWN> to highlight Address.
4. Press <ENTER> and a number from 001–512 will show on the display.
5. Use <UP> or <DOWN> to change the number to the desired DMX starting address.
6. Press <ENTER> to select the DMX starting address.
DMX Personalities The Intimidator™ Wash Zoom 350 IRC has 2 DMX personalities: a 14-channel personality
and a 29-channel personality.
To set the DMX personality, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Run Mode icon.
3. Press <ENTER> and the Run Mode options will show on the display.
4. Use <UP> or <DOWN> to highlight DMX.
5. Press <ENTER>. A green dot will show on the DMX option line and the characters 14CH
or 29CH will show in green.
6. Use <UP> or <DOWN> to switch between 14CH and 29CH.
7. Press <ENTER> to select the DMX personality shown.
After the DMX starting address and personality have been set, there will be a delay of
30 seconds before the display automatically returns to showing the current DMX
address and the DMX personality.
If the display goes blank after 30 seconds, it is because the Display option is set to
OFF. To set the Display option to ON go to Menu > Setup > Display and change the
value to ON. For more information see the Display ON/OFF.
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 13 of 31
DMX Channel The following table outlines all the capabilities of the Intimidator™ Wash Zoom 350 and the
Assignments and channels that control them when the light is used with a lighting controller.
Values
29-CH
Channel
Function
Value
Percent/Setting
1
Pan
000 ó 255
0 to 540°
2
Fine Pan
000 ó 255
Fine control of panning
3
Tilt
000 ó 255
0 to 270°
4
Fine Tilt
000 ó 255
Fine control of tilting
3
Speed
000 ó 255
Pan/Tilt (fast to slow)
6
Red
000 ó 255
0 to 100%
7
Green
000 ó 255
0 to 100%
8
Blue
000 ó 255
0 to 100%
9
White
000 ó 255
0 to 100%
10
Red
000 ó 255
0 to 100%
11
Green
000 ó 255
0 to 100%
12
Blue
000 ó 255
0 to 100%
13
White
000 ó 255
0 to 100%
14
Red
000 ó 255
0 to 100%
15
Green
000 ó 255
0 to 100%
16
Blue
000 ó 255
0 to 100%
17
White
000 ó 255
0 to 100%
18
Red
000 ó 255
0 to 100%
19
Green
000 ó 255
0 to 100%
20
Blue
000 ó 255
0 to 100%
21
White
000 ó 255
0 to 100%
000 ó 004
No function
005 ó 009
Color 1
010 ó 014
Color 2
015 ó 019
Color 3
020 ó 024
Color 4
025 ó 029
Color 5
030 ó 034
Color 6
035 ó 039
Color 7
040 ó 044
Color 8
045 ó 049
Color 9
050 ó 054
Color 10
055 ó 059
Color 11
060 ó 064
Color 12
065 ó 069
Color 13
22
Colors
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Zone 1
Zone 2
Zone 3
Zone 4
Page 14 of 31
29-CH
Channel
22 (Cont.)
23
Function
Colors
(Cont.)
Built-in
Control
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Value
Percent/Setting
070 ó 074
Color 14
075 ó 079
Color 15
080 ó 084
Color 16
085 ó 089
Color 17
090 ó 094
Color 18
095 ó 099
Color 19
100 ó 104
Color 20
105 ó 109
Color 21
110 ó 114
Color 22
115 ó 119
Color 23
120 ó 124
Color 24
125 ó 129
Color 25
130 ó 134
Color 26
135 ó 139
Color 27
140 ó 144
Color 28
145 ó 149
Color 29
150 ó 154
Color 30
155 ó 159
Color 31
160 ó 164
Color 32
165 ó 169
Color 33
170 ó 174
Color 34
175 ó 179
No function
180 ó 201
Clockwise color change (fast to slow)
202 ó 207
Stop (color stays in the current color)
208 ó 229
Counter-clockwise color change
(slow to fast)
230 ó 234
No function
235 ó 249
Color jump (fast to slow)
250 ó 255
Sound colors
000 ó 015
No function
016 ó 031
Zone macro 1
032 ó 047
Zone macro 2
048 ó 063
Zone macro 3
064 ó 079
Zone macro 4
080 ó 095
Zone macro 5
096 ó 111
Zone macro 6
112 ó 127
Built-in 7 (zone macros 1—6)
Page 15 of 31
29-CH
Channel
23 (Cont.)
Function
Built-in
Control
(Cont.)
Value
Percent/Setting
128 ó 143
Built-in 8
144 ó 159
Built-in 9
160 ó 175
Built-in 10
176 ó 191
Built-in 11
192 ó 207
Built-in 12
208 ó 223
Built-in 13
224 ó 239
Built-in 14
240 ó 255
Built-in 15 (built-in 8—14)
24
Built-in
Speed
000 ó 255
Zones and built-in speed (slow to fast)
25
Dimmer
000 ó 255
0 to 100%
000 ó 019
Closed
020 ó 024
Open
025 ó 064
Strobe effect (decreasing speed)
065 ó 069
Open
070 ó 084
Fast on, slow off (decreasing speed)
085 ó 089
Open
090 ó 104
Slow on, fast off (decreasing speed)
105 ó 109
Open
110 ó 124
Random shutter (decreasing speed)
125 ó 129
Open
130 ó 144
Random fast on, slow off (decreasing speed)
145 ó 149
Open
150 ó 164
Random slow on, fast off (decreasing speed)
165 ó 169
Open
170 ó 184
Pulse effect 1 (decreasing speed)
185 ó 189
Open
190 ó 204
Pulse effect 2 (decreasing speed)
205 ó 209
Open
210 ó 224
Gradually on and off (decreasing speed)
225 ó 229
Open
230 ó 244
Pulse effect 3 (decreasing speed)
245 ó 255
Open
000 ó 255
Zoom (wide to narrow)
000 ó 009
No function
010 ó 014
Blackout while panning/tilting
015 ó 049
No function
26
27
28
Shutter
Zoom
Control
Functions
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 16 of 31
29-CH
Channel
28 (Cont.)
29
Function
Control
Functions
(Cont.)
Movement
Macros
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Value
Percent/Setting
050 ó 054
Reset pan
055 ó 059
Reset tilt
060 ó 064
Reset zoom
065 ó 069
No function
070 ó 074
Reset all
075 ó 079
No function
080 ó 084
Reverse pan/tilt
085 ó 089
Reverse pan
090 ó 094
Reverse tilt
095 ó 099
Cancel reverse pan
100 ó 104
Cancel reverse tilt
105 ó 109
Cancel reverse pan/tilt
110 ó 114
Pan/Tilt normal speed
115 ó 119
Pan/Tilt fast speed
120 ó 124
Pan/Tilt slow speed
125 ó 129
Fan (full speed)
130 ó 134
Fan (auto)
135 ó 139
Dimmer, fast
000 ó 007
No function
008 ó 023
Automatic movement macro 1
024 ó 039
Automatic movement macro 2
040 ó 055
Automatic movement macro 3
056 ó 071
Automatic movement macro 4
072 ó 087
Automatic movement macro 5
088 ó 103
Automatic movement macro 6
104 ó 119
Automatic movement macro 7
120 ó 135
Automatic movement macro 8
136 ó 151
Sound-Active movement macro 1
152 ó 167
Sound-Active movement macro 2
168 ó 183
Sound-Active movement macro 3
184 ó 199
Sound-Active movement macro 4
200 ó 215
Sound-Active movement macro 5
216 ó 231
Sound-Active movement macro 6
232 ó 247
Sound-Active movement macro 7
248 ó 255
Sound-Active movement macro 8
Page 17 of 31
14-CH
Channel
Function
Value
Percent/Setting
1
Pan
000 ó 255
0 to 540°
2
Tilt
000 ó 255
0 to 270°
3
Speed
000 ó 255
Pan/Tilt (fast to slow)
4
Red
000 ó 255
0 to 100%
5
Green
000 ó 255
0 to 100%
6
Blue
000 ó 255
0 to 100%
7
White
000 ó 255
0 to 100%
000 ó 015
No function
016 ó 031
Zone macro 1
032 ó 047
Zone macro 2
048 ó 063
Zone macro 3
064 ó 079
Zone macro 4
080 ó 095
Zone macro 5
096 ó 111
Zone macro 6
112 ó 127
Built-in 7 (zone macros 1—6)
128 ó 143
Built-in 8
144 ó 159
Built-in 9
160 ó 175
Built-in 10
176 ó 191
Built-in 11
192 ó 207
Built-in 12
208 ó 223
Built-in 13
224 ó 239
Built-in 14
240 ó 255
Built-in 15 (built-in 8—14)
8
Built-in
Control
9
Built-in
Speed
000 ó 255
Zones and built-in speed (slow to fast)
10
Dimmer
000 ó 255
0 to 100%
000 ó 019
Closed
020 ó 024
Open
025 ó 064
Strobe effect (decreasing speed)
065 ó 069
Open
070 ó 084
Fast on, slow off (decreasing speed)
085 ó 089
Open
090 ó 104
Slow on, fast off (decreasing speed)
105 ó 109
Open
110 ó 124
Random shutter (decreasing speed)
125 ó 129
Open
130 ó 144
Random fast on, slow off (decreasing speed)
145 ó 149
Open
11
Shutter
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 18 of 31
14-CH
Channel
11
12
13
14
Function
Shutter cont.
Zoom
Control
Functions
Movement
Macros
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Value
Percent/Setting
150 ó 164
Random slow on, fast off (decreasing speed)
165 ó 169
Open
170 ó 184
Pulse effect 1 (decreasing speed)
185 ó 189
Open
190 ó 204
Pulse effect 2 (decreasing speed)
205 ó 209
Open
210 ó 224
Gradually on and off (decreasing speed)
225 ó 229
Open
230 ó 244
Pulse effect 3 (decreasing speed)
245 ó 255
Open
000 ó 255
Zoom in and out
000 ó 009
No function
010 ó 014
Pan/Tilt blackout
015 ó 049
No function
050 ó 054
Reset pan
055 ó 059
Reset tilt
060 ó 064
Reset zoom
065 ó 069
No function
070 ó 074
Reset all
075 ó 079
No function
080 ó 084
Reverse Pan/Tilt
085 ó 089
Reverse pan
090 ó 094
Reverse tilt
095 ó 099
Cancel reverse pan
100 ó 104
Cancel reverse tilt
105 ó 109
Cancel reverse pan/tilt
110 ó 114
Pan/Tilt normal speed
115 ó 119
Pan/Tilt fast speed
120 ó 124
Pan/Tilt slow speed
125 ó 129
Fan (full speed)
130 ó 134
Fan (auto)
135 ó 139
Dimmer, fast
140 ó 144
Dimmer, smooth
145 ó 255
No function
000 ó 007
No function
008 ó 023
Automatic movement macro 1
024 ó 039
Automatic movement macro 2
040 ó 055
Automatic movement macro 3
Page 19 of 31
14-CH
Channel
14 (Cont.)
Function
Movement
Macros
(Cont.)
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Value
Percent/Setting
056 ó 071
Automatic movement macro 4
072 ó 087
Automatic movement macro 5
088 ó 103
Automatic movement macro 6
104 ó 119
Automatic movement macro 7
120 ó 135
Automatic movement macro 8
136 ó 151
Sound-Active movement macro 1
152 ó 167
Sound-Active movement macro 2
168 ó 183
Sound-Active movement macro 3
184 ó 199
Sound-Active movement macro 4
200 ó 215
Sound-Active movement macro 5
216 ó 231
Sound-Active movement macro 6
232 ó 247
Sound-Active movement macro 7
248 ó 255
Sound-Active movement macro 8
Page 20 of 31
Configuration
(Standalone)
Use standalone configurations to operate the product without a DMX controller.
Never connect a product operating in a standalone mode (Sound, Auto, or IR) to a
DMX chain that includes a DMX controller. Products in standalone mode can transmit
DMX signals that interfere with the DMX signals from the controller
Sound Mode Sound mode sets the product to respond to sounds and music.
To set the product to Sound mode, do the following:
1. Make sure the product is connected to a power source and not connected to a DMX
controller.
2. Press <MENU> repeatedly until 4 icons show on the display.
3. Use <UP> or <DOWN> to highlight the Run Mode icon.
4. Press <ENTER> and the Run Mode options will show on the display.
5. Use <UP> or <DOWN> to highlight the Sound option.
6. Press <ENTER>. A green dot will show on the Sound option line and the product will
begin reacting to sound.
The product will respond only to low frequencies of music (bass and drums).
If the product is not responding to sound, increase the sensitivity. For more
information see the Sensitivity Setting below.
Auto Mode Auto mode sets the product to 1 of 16 preset movement patterns and color changes.
To set the product to Auto mode, do the following:
1. Make sure the product is connected to a power source and not connected to a DMX
controller.
2. Press <MENU> repeatedly until 4 icons show on the display.
3. Use <UP> or <DOWN> to highlight the Run Mode icon.
4. Press <ENTER> and the Run Mode options will show on the display.
5. Use <UP> or <DOWN> to highlight the Auto option.
6. Press <ENTER>. A green dot will show on the Auto option line, the current Auto mode
will show up in green letters and the product will begin moving and emitting light.
7. Use <UP> or <DOWN> to cycle through the 16 Auto modes.
8. Press <ENTER>> to select one of the 16 Auto modes.
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 21 of 31
IR Mode IR mode allows the product to be controlled with an infrared remote controller. The IRC-6
can remotely set the product to various modes; adjust the color, speed and sensitivity; and
set the strobe.
To set the product to IR mode, do the following:
Make sure the product is plugged into a power source and not connected to a DMX cable.
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Run Mode icon.
3. Press <ENTER>. The Run Mode options will show on the display.
4. Use <UP> or <DOWN> to highlight the IR option.
5. Press <ENTER>. A green dot will show on the IR option line and the product will begin
moving and emitting light.
IRC-6 Operation
The IRC-6 infrared controller (available from CHAUVET®) allows remote control of the
Intimidator Wash Zoom 350 IRC.
Be sure the IRC-6 remote is pointing directly at the product and there is nothing in
between the remote and the product.
Some of the buttons on the remote work differently than what is indicated on their
labels. For example:
· <MANUAL> controls the white color in the LEDs.
· <A>, <UV>, and <W> control the Blackout function.
Please read the next section carefully.
The list below describes which features each button controls.
· <BLACKOUT> - Turns LEDs on and off.
· <AUTO> - Activates Auto mode. Use the <+> and <-> buttons to cycle through Auto
modes.
· <SOUND> - Activates Sound mode.
· <STROBE> - Activates the strobe. Use the <+> and <-> buttons to cycle through strobe
speeds.
· <SPEED> - Adjusts the movement speed. Use the <+> and <-> buttons to cycle through
movement speeds.
· <SENSITIVITY> - Adjusts sound sensitivity. Use the <+> and <-> buttons to cycle
through sound sensitivity levels.
· <%> - Adjusts the brightness of the LEDs. Use the <+> and <-> buttons to increase or
decrease the brightness of the LEDs.
· <MANUAL> - Adjusts the white color in the LEDs. Use the <+> and <-> buttons to
increase or decrease the white color in the LEDs.
· <FADE/SNAP> or <FADE> - Adjusts the speed and type of color fades. Press the button
to switch between fade and snap color changes. Use <+> and <-> to increase or
decrease the speed of the color changes.
· <R> - Adjusts the red color in the LEDs. Use the <+> and <-> buttons to increase or
decrease the red color in the LEDs.
· <G> - Adjusts the green color in the LEDs. Use the <+> and <-> buttons to increase or
decrease the green color in the LEDs.
· <B> - Adjusts the blue color in the LEDs. Use the <+> and <-> buttons to increase or
decrease the blue color in the LEDs.
· <+> - Increases values for controls as described above.
· <-> - Decreases values for controls as described above.
· <0>–<9> - Activates specific Auto modes. Can be used as a shortcut for the combination
of the <AUTO> button and the <+> and <-> buttons.
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 22 of 31
Configuration
(Master/Slave)
Master/Slave mode allows a single Intimidator™ Wash Zoom 350 IRC (the master) to
control the actions of one or more Intimidator™ Wash Zoom 350 IRCs (the slaves) without
a DMX controller.
In Master/Slave mode the master is set to operate in Auto mode, Sound mode, or IR mode
and the slaves are set to operate in Slave mode.
The master and slaves are daisy chained though the DMX input and output ports with the
master at the beginning of the chain. Once set and connected, the slaves will operate
identically to, and in unison with, the master.
· Always put the male DMX connector into the master. Do not connect to the DMX
In port on the master.
· Never connect more than 31 slaves to the master.
· Never connect a DMX controller to a DMX daisy chain of master and slaves.
· Configure all the slaves before connecting the master to the DMX daisy chain.
Configuring the Configure the slaves for Slave mode before or after they are put in position, and before
Slaves they are daisy chained to the master.
To configure a slave, do the following:
1. Make sure the product is connected to a power source.
2. Press <MENU> repeatedly until 4 icons show on the display.
3. Use <UP> or <DOWN> to highlight the Run Mode icon.
4. Press <ENTER>. The Run Mode options will show on the display.
5. Use <UP> or <DOWN> to highlight the Slave option.
6. Press <ENTER>. A green dot will show on the Slave option line.
Configuring the Configure the master after all the slaves are connected to it and configured.
Master To configure the master, do the following:
1.
2.
3.
4.
Make sure the product is connected to a power source and connected to all the slaves.
Press <MENU> repeatedly until 4 icons show on the display.
Use <UP> or <DOWN> to highlight the Run Mode icon.
Select any of the Standalone modes as described in Configuration (Standalone).
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 23 of 31
Configuration
(Settings)
The Intimidator™ Wash Zoom 350 IRC can be customized with settings such as for
movement, speed, display, and fan operation. Below are instructions for configuring all the
settings available.
Pan Reverse Reversing the pan movement is useful when 2 lights are facing each other and they both
need to turn toward the same direction.
To reverse the pan movement do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Setup icon.
3. Press <ENTER>. The Setup options will show on the display.
4. Use <UP> or <DOWN> to highlight the Pan Reverse option.
5. Press <ENTER>. The words ON or OFF will show in green.
6. Use <UP> or <DOWN> to switch between ON and OFF.
7. Press <ENTER> to select the setting.
Tilt Reverse Reversing the tilt movement is useful when 2 lights are facing each other and they need to
point towards the same space between them.
To reverse the tilt movement do the following:Press <MENU> repeatedly until 4 icons show
on the display.
1. Use <UP> or <DOWN> to highlight the Setup icon.
2. Press <ENTER>. The Setup options will show on the display.
3. Use <UP> or <DOWN> to highlight the Tilt Reverse option.
4. Press <ENTER>. The words ON or OFF will show in green.
5. Use <UP> or <DOWN> to switch between ON and OFF.
6. Press <ENTER> to select the setting.
Pan Range Setting the pan angle range is useful when there is an area of the room that the
Intimidator™ Wash Zoom 350 IRC should not illuminate.
To set the range of the pan movement, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use the <UP> and <DOWN> buttons to highlight the Setup icon.
3. Press <ENTER>. The Setup options will show on the display.
4. Use the <UP> and <DOWN> buttons to highlight the Pan Angle option.
5. Press <ENTER>. The three digits to the right will show in green.
6. Use <UP> or <DOWN> to select 180, 360, or 540.
7. Press <ENTER> to select the setting.
Tilt Range Setting the tilt angle range is useful when there is an area of the room that the Intimidator™
Wash Zoom 350 IRC should not illuminate.
To set the range of the tilt movement, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Setup icon.
3. Press <ENTER>. The Setup options will show on the display.
4. Use <UP> or <DOWN> to highlight the Tilt Angle option.
5. Press <ENTER>. The three digits to the right will show in green.
6. Use <UP> or <DOWN> to select 90, 180, or 270.
7. Press <ENTER> to select the setting.
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 24 of 31
Movement Speed The movement, or pan and tilt speed, can be adjusted and will affect the speed of the Auto
and Sound modes.
To set the pan and tilt speed, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Setup icon.
3. Press <ENTER>. The Setup options will show on the display.
4. Use <UP> or <DOWN> to highlight the P/T Speed option.
5. Press <ENTER> and Normal, Fast, or Slow will show in green.
6. Use <UP> or <DOWN> to select the desired speed.
7. Press <ENTER> to select the setting.
Fan Operation The fans in the unit can be set to Full to remain on or set to Auto to run only when the
product is hot enough to need a fan.
To set the fans to Full or Auto, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Setup icon.
3. Press <ENTER>. The Setup options will show on the display.
4. Use <UP> or <DOWN> to highlight the Fans option.
5. Press <ENTER>. The words Full or Auto will show in green.
6. Use <UP> or <DOWN> to switch between Full and Auto.
7. Press <ENTER> to select the setting.
Display ON/OFF The display can be set to stay on permanently (ON), or to go off (OFF) when the menu is
not being used.
If the display is set to ON, it will remain in any given menu for 30 seconds of inactivity, and
then it will return to a home screen that shows the product’s current mode and DMX
address.
If the display is set to OFF, it will remain in any given menu for 30 seconds of inactivity, and
then it will go blank and show nothing.
To set the display ON or OFF, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Setup icon.
3. Press <ENTER>. The Setup options will show on the display.
4. Use <UP> or <DOWN> to highlight the Display option.
5. Press <ENTER>. The words ON or OFF will show in green.
6. Use <UP> or <DOWN> to switch between ON and OFF.
7. Press <ENTER> to select the setting.
If the display is set to OFF, it will come back on when the IRC-6 is used or when any
menu button is pressed; however, it will not come on when it receives DMX control.
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 25 of 31
Display Orientation The display can show the screen in two directions, one for when the fixture is standing and
one for when it is mounted upside-down.
To set the display orientation, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Setup icon.
3. Press <ENTER>. The Setup options will show on the display.
4. Use <UP> or <DOWN> to highlight the Screen Rev option.
5. Press <ENTER>. The words ON or OFF will show in green.
6. Use <UP> or <DOWN> to switch between ON (upside-down display) and
OFF (normal display).
7. Press <ENTER> to select the setting.
Dimming Curve The dimming curve can be adjusted to change how the light brightens and dims. If the
factory default is not a suitable setting, and the dimming curve of this light needs to match
more closely to that of another light, adjust this setting as follows.
To adjust the dimming curve, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Setup icon.
3. Press <ENTER>. The Setup options will show on the display.
4. Use <UP> or <DOWN> to highlight the Dimmer Curve option.
5. Press <ENTER> and Square, I Squa, SCurve, or Linear will show in green.
6. Use <UP> or <DOWN> to select the desired option.
7. Press <ENTER> to select the setting.
Dimming Speed The dimming speed can be adjusted to change how quickly the light brightens and dims. If
the factory default is not a suitable setting, and the dimming speed of this light needs to
match more closely to that of another light, adjust this setting as follows.
To adjust the dimming speed, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Setup icon.
3. Press <ENTER>. The Setup options will show on the display.
4. Use <UP> or <DOWN> to highlight the Dimmer Speed option.
5. Press <ENTER> and Fast or Smooth will show in green.
6. Use <UP> or <DOWN> to switch between Fast and Smooth.
7. Press <ENTER> to select the setting.
Color Balance The color balance setting is used to set the white color of the product. This setting affects
only the color of the white light of the LED. The red, green, and blue colors will remain the
same.
To adjust the color balance, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Setup icon.
3. Press <ENTER>. The Setup options will show on the display.
4. Use <UP> or <DOWN> to highlight the Color Balance option.
5. Press <ENTER>. The product will begin emitting light and the Color Balance options will
show on the display.
6. Use <UP> or <DOWN> to highlight the color to be adjusted.
7. Press <ENTER>. The number to the right will show in green
8. Use <UP> or <DOWN> to select a value between 100 and 255. The higher the number,
the more of the color is included in the white setting.
9. Press <ENTER> to select the value setting.
10. Repeat steps 6 through 9 to adjust the remaining colors until the desired white color is
emitted from the product.
Upon entering the color balance menu, the product will emit a white light. After
exiting the color balancing menu, the product will return to the currently selected
operations mode. If there is no activity for 30 seconds, the product will exit the color
balance menu and return to the currently selected operations mode.
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 26 of 31
Sensitivity The sensitivity setting adjusts the sensitivity of the product’s microphone. If the product is
not responding to the beat of the music in Sound mode, set the sensitivity to a higher
number until the product responds.
To adjust the sensitivity setting, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Setup icon.
3. Press <ENTER>. The Setup options will show on the display.
4. Use <UP> or <DOWN> to highlight the Sensitivity option.
5. Press <ENTER>. The number to the right will show in green.
6. Use <UP> or <DOWN> to select a sensitivity level. The least sensitive is 1 and the most
sensitive is 100.
7. Press <ENTER> to select the setting.
Reset Resetting will restart the product. It does not change any settings. Resetting is a helpful
troubleshooting tool, and can be used if the product has stopped responding to control, or if
the control system has suffered a failure.
To reset the product, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Setup icon.
3. Press <ENTER>. The Setup options will show on the display.
4. Use <UP> or <DOWN> to highlight the Reset option.
5. Press <ENTER>. The product will immediately reset.
Reset to Factory Resetting to factory defaults will clear out all customized settings and return thee settings to
Defaults the factory defaults. Resetting to factory defaults can be used if the product is behaving
inconsistently.
To reset the product to factory default settings, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Setup icon.
3. Press <ENTER>. The Setup options will show on the display.
4. Use <UP> or <DOWN> to highlight the Factory Set option.
5. Press <ENTER>. The product will immediately reset to factory default settings.
System
Information
To see the product’s current software version, running mode, DMX address and
temperature, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Sys Info icon.
3. Press <ENTER>. The current information about the product will show on the display.
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 27 of 31
5. TECHNICAL INFORMATION
Product
Maintenance
Dust build-up on the lens reduces light output. Dust build-up on the body and fans can
cause overheating and mechanical wear, which can reduce the usable life of the product.
To maintain optimum performance and minimal wear in a normal environment, clean the
product at least twice a month. If the environment is particularly dusty, clean the product
more often.
For best results follow the suggestions listed below:
· Never clean the product when it is plugged into a power source.
· Only clean the product when it is at room temperature.
· Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the
external surfaces and in the vents.
· Use a mild soap solution, ammonia-free glass cleaner, or isopropyl alcohol to clean all
the external optics and glass or transparent surfaces.
· Apply the cleaning solution directly to a soft, lint-free cotton cloth or a lens cleaning
tissue.
· Gently wipe dirt and grime to the outside edges of the external optics and glass or
transparent surfaces.
· Gently polish the external optics and glass or transparent surfaces until they are free of
haze and lint.
Always dry the external optics and glass/transparent surfaces carefully after cleaning
them.
Do not spin the cooling fans while blowing compressed air into them.
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 28 of 31
6. TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Power
Length
Width
Height
10.6 in (270 mm)
7.6 in (194 mm)
14.3 in (363 mm)
Note: Dimensions in inches are rounded to the nearest decimal digit
Weight
16 lb (7.3 kg)
Power Supply Type
Range
Voltage Selection
Switching (internal)
Parameter
100 to 240 VAC, 50/60 Hz
120 V, 60 Hz
Auto-ranging
230 V, 50 Hz
Consumption
Operating current
248 W
2.3 A
240 W
1.1 A
Fuse
Power I/O
F 5 A, 250 V
US/Canada
F 5 A, 250 V
UK/Worldwide
Power input connector
Power output connector
IEC
Edison (US)
IEC
N/A
Power cord plug
Edison (US)
Local plug
Power linking current (units)
Type
13.6 A (5 units)
Power
13.6 A (12 units)
Lifespan
LED
Color
20 W
Quantity
50,000 hours
Current
RGBW
Parameter
7
3.7 A
Illuminance @ 2 m (14°)
14,520 lux
Illuminance @ 2 m (58°)
Zoom angle
2,348 lux
14° to 58°
Strobe rate
Pan and Tilt
0–20 Hz
540° pan
Pan/Tilt ranges
Maximum External Temp.
180°/360°/540° pan ranges
Cooling System
DMX
104 °F (40 °C)
I/O Connectors
Fan-cooled
Connector Type
Channel Range
Ordering
3-pin XLR
Product Name
Sockets
Item Code
14 or 29
UPC Number
Intimidator™ Wash Zoom 350 IRC
08010789
781462211370
Light Source
Photo Optic
Thermal
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
270° tilt
90°/180°/270° tilt ranges
Page 29 of 31
RETURNS
General Info
To return a product or request support:
· In the U.S., contact CHAUVET® World Headquarters (see below).
· In the UK or Ireland, contact CHAUVET® Europe Ltd. (see below).
· In Mexico, contact CHAUVET® Mexico (see below).
· In any other country, DO NOT contact CHAUVET®. Contact your distributor. See
www.chauvetlighting.com for distributors outside the U.S., United Kingdom, Ireland, or
Mexico.
If you live outside the U.S., United Kingdom, Ireland, or Mexico, contact your
distributor of record and follow their instructions on how to return CHAUVET®
products to them. Visit our website for contact details.
U.S., UK, Ireland,
and Mexico
Call the corresponding CHAUVET® Technical Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product. Be prepared to
provide the model number, serial number, and a brief description of the reason for the
return.
You must send the merchandise prepaid, in its original box, and with its original packing
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write the following information on a piece of paper and
place it inside the box:
· Your name
· Your address
· Your phone number
· RMA number
· A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. FedEx packing or double-boxing are recommended.
CHAUVET® reserves the right to use its own discretion to repair or replace returned
product(s).
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 30 of 31
CONTACT US
WORLD HEADQUARTERS - CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice:
(954) 577-4455
Fax:
(954) 929-5560
Toll free: (800) 762-1084
Technical Support
Voice:
(954) 577-4455 (Press 4)
Fax:
(954) 756-8015
Email:
tech@chauvetlighting.com
World Wide Web www.chauvetlighting.com
UNITED KINGDOM AND IRELAND - CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice:
+44 (0)1773 511115
Fax:
+44 (0)1773 511110
Technical Support
Email:
uktech@chauvetlighting.com
World Wide Web www.chauvetlighting.co.uk
MEXICO - CHAUVET® Mexico
General Information
Address: Av. Santa Ana 30
Parque Industrial Lerma
Lerma, Mexico C.P. 52000
Voice:
+52 (728) 285-5000
Technical Support
Email:
servicio@chauvet.com.mx
World Wide Web www.chauvet.com.mx
Outside the U.S., United Kingdom, Ireland, or Mexico, contact your dealer. Follow their instructions to request support
or to return a product. Visit our website for contact details.
Intimidator™ Wash Zoom 350 IRC User Manual Rev. 1
Page 31 of 31
Download PDF