null  null
6300 VEHICULAR
SWING GATE
OPERATOR
entrapment
prevention system
reverses gate on contact
•A
utomatic self-setting
limits mean no limit switch
adjustments – ever
•S
afety – built-in
mechanical and electronic
reverse system
pad mount
smooth operation
no slamming when gate closes
•A
dvanced microprocessor
control board features
programming switches to
set the mode of operation
required and has ports for
DKS plug-in loop detectors
to simplify wiring
•P
olyurethane cover protects
all critical components from
the environment
•G
90 galvanized steel frame
prevents rusting
arm joint cover
helps eliminate pinch points
•A
dvanced “Stop-Reverse”
action eliminates damage
commonly found in instant
reverse style operators
•B
i Parting Gate System both operators run from
a single control board for
sequenced operation
post mount
unique design
simplifies installation and
provides easy access to all
internal parts
ACCESS CONTROL SOLUTIONS
•T
his operator meets or
exceeds the requirements
of the UL 325 and UL 991
safety standards and is
ETL Listed
• 5-year limited warranty
FEATURES
•E
lectronic magnetic
limits eliminate old style
mechanical switches that
can wear out, break or fail
6300 VEHICULAR
SWING GATE OPERATORS
The DKS 6300 swing gate operator is designed for residential, commercial, and industrial
applications for both single and dual-leaf gates. The unique design of this operator allows the
gate arm to rotate from underneath the operator, creating an aesthetically pleasing installation
and allowing the arm to attach to the bottom rail of the gate, were it is virtually unseen from
outside the gate. This important feature does not require any unsightly cross bars to be welded
to the gate, and the bottom rail is one of the strongest points on the gate. These operators are
designed to be pad or post mounted to meet almost any installation requirement.
Pad mount adds 10.25” (260mm) to Height dimension.
6300 1/2 & 1 HP
Post mount operator Height is adjustable by the installer.
with Convenience Open package. 16.25” W x 13.5” H x 32” D (413mm W x 343mm H x 813mm D)
6300 1/2 HP Specs
Class of
operation
I, II, III, IV
Max Gate Length *
18 Ft 5.5 m
Max Gate
HP Weight *
700 Lbs.*** 1/2 HP 60 cycles/hr
317.5 kg
continuous duty
Power 115 VAC, 60 Hz, 5.4A
230 VAC, 60 Hz, 2.7A**
460 VAC, 60 Hz, 1.4A**
* Assumes gate and hardware to be in good condition and swinging in a level plane
*** 600 Lbs with Convenience Open
Convenience
Open Package
Optional
factory installed DC powered drive
system provides an automatic
method to open a gate when primary
(AC) power fails
6300 1 HP Specs
Class of
operation
I, II, III, IV
Max Gate Length *
22 Ft 6.7 m
Max Gate
HP Weight *
800 Lbs.**** 1 HP 60 cycles/hr
362 kg
continuous duty
Power 115 VAC, 60 Hz, 9.7A
230 VAC, 60 Hz, 4.9A**
460 VAC, 60 Hz, 2.5A**
* Assumes gate and hardware to be in good condition and swinging in a level plane
** These operators use a step-down transformer, to achieve 115 VAC operating voltage
**** 700 Lbs with Convenience Open
Convenience
Open Package
Optional
factory installed DC powered drive
system provides an automatic
method to open a gate when primary
(AC) power fails
General Specs
Mechanical
Advanced Features
Safety Standards
Primary Reduction: Pulley/belt driving a worm gear
Automatic limit adjustment
Speed:Rotates gate 90° in approximately
16-18 seconds
Auto-close timer 1-23 seconds
Complies with the UL 325 and UL 991
safety standards
Frame:
G90 galvanized steel to prevent rusting
Arm:Articulating arms to allow mechanical
slow start / slow stop
Mounting:Pad or post mount – specify which
when ordering
Manual Release
Gate overlap feature for bi-parting gate operation
Includes primary and built-in secondary
entrapment prevention system
Tamper protect feature
Built-in On/Off switch
Heater kit recommended for
colder environments
Shipping Weight
Approximately 120-160 lbs (54-73 kg)
Depending on model and options selected.
Clutch can be back-driven to allow
fail-safe release
Two 115 VAC convenience outlets for
accessory transformers
Ports for plug-in open and reverse loop
detectors. DKS plug-in detectors only.
Gate Tacker reporting output provides
operator data to access control system
(DKS systems with card access only)
®
D O O R K I N G, I N C.
120 Glasgow Avenue, Inglewood, California 90301 U.S.A. Tel: 310-645-0023 FAX: 310-641-1586 www.doorking.com
© 2011 All Rights Reserved. Product specifications may change without notice. Rev. 2/11
MEMBER:
10ºF to 115ºF (-12ºC to 46ºC)
Selectable shadow / reverse loop function
Magnetic lock output
External obstruction sensing devices must be
used with this operator
Operating Temp
Built-in alarm reset switch
Keyed padlock provided
Safety
ETL listed
Warranty
5-year limited factory warranty
Distributed by:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement