RGBlink | VSP 1314 | User`s manual | RGBlink VSP 1314 User`s manual

VSP 1314
User’s Manual
 Manual #:RGB-RD-UM-V1314 E001
 Revision:V1.0
–
VSP 1314
User’s Manual
1
VSP 1314·User’s Manual
Thank you for choosig our products! In order to allow you to learn how to
use the video processor quickly, we bring you the detailed user’s guide.
You can read the introduction and directions before using the video
processor, please read all the information we provide carefully to use our
products correctly.
Copyright
©2012 All rights reserved by RGBLINK.
This document is done by Xiamen RGBlink Science & Technolog Co.,Ltd
independently. No part may be copied, reproduced or translated without
permission.
Notice
RGBlink provides this manual ―as is‖ without warranty of any kind,
either expressed or implied, including but not limited to the implied
warranties or merchantability and fitness for a particular purpose. RGBlink
may make improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice. This
publication could contain technical inaccuracies or typographical errors.
Changes are periodically made to the information in this publication; these
changes are incorporated in new editions of this publication.
Statement
This equipment has been tested and found to comply with the limits for a
class A digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this
equipment in a residential area may cause harmful interference, in which
case the user will be responsible for correcting any interference.
Guarantee and Compensation
RGBlink provides a guarantee relating to perfect manufacturing as part of
the legally stipulated terms of guarantee. On receipt, the purchaser must
immediately inspect all delivered goods for damage incurred during
transport, as well as for material and manufacturing faults. RGBlink must
VSP 1314
User’s Manual
2
be informed immediately in writing of any complains. The period of
guarantee begins on the date of transfer of risks, in the case of special
systems and software on the date of commissioning, at latest 30 days after
the transfer of risks. In the event of justified notice of compliant, RGBlink
can repair the fault or provide a replacement at its own discretion within an
appropriate period. If this measure proves to be impossible or unsuccessful,
the purchaser can demand a reduction in the purchase price or
cancellation of the contract. All other claims, in particular those relating to
compensation for direct or indirect damage, and also damage attributed to
the operation of software as well as to other service provided by RGBlink,
being a component of the system or independent service, will be deemed
invalid provided the damage is not proven to be attributed to the absence of
properties gurranteed in writing or due to the intent or gross negligence or
part of RGBlink. If the purchaser or a third party carries out modifications or
repairs on goods delivered by RGBlink, or if the goods are handled
incorrectly, in particular if the systems are commissioned operated
incorrectly or if, after the transfer of risks, the goods are subject to
influences not agreed upon in the contract, all guarantee claims of the
purchaser will be rendered invalid. Not included in the guarantee coverage
are system failures which are attributed to programs or special electronic
circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as
normal maintenance are not subject to the guarantee provided by RGBlink
either. The environmental conditions as well as the servicing and
maintenance regulations specified in this manual must be complied with by
the customer.
Trademarks
Brand and product names mentioned in this manual may be trademarks,
registered trademarks or copyrights of their respective holders. All brand
and product names mentioned in this manual serve as comments or
examples and are not to be understood as advertising for the products or
their manufactures.
VSP 1314
User’s Manual
3
Company address
RGBlink Science & Technology Co., Ltd.
Headquarter: S603~604 Weiye Building Torch Hi-Tech Industrial
Development Zone Xiamen, Fujian Province, P.R.C
Shenzhen office: Building 3, A Baiwang Plaza, Xili Nanshan District
Shenzhen, Guangdong Province, P.R.C
Beijing office:Room 410, Building 3, Dongyi International Business
Park, No.8 Gaojing Culture Garden, Chaoyang District, Beijing, P.R.C
Shanghai office:Building 3, 1358 Nong, Tongpu Road,
Shanghai,P.R.C
VSP 1314



Tel: +86-592-5771197
Fax:+86-592-5771202
Websites:

~ http://www.rgblink.com
~ http://www.rgblink.cn
E-mail:rgblinkcs@gmail.com
User’s Manual
4
Operators Safety Summary
The general safety information in this summary is for operating personnel.
Do Not Remove Covers or Panels
There are no user-serviceable parts within the unit. Removal of the top
cover will expose dangerous voltages. To avoid personal injury, do not
remove the top cover. Do not operate the unit without the cover installed.
Power Source
This product is intended to operate from a power source that will not apply
more than 230 volts rms between the supply conductors or between both
supply conductor and ground. A protective ground connection by way of
grounding conductor in the power cord is essential for safe operation.
Grounding the Product
This product is grounded through the grounding conductor of the power
cord. To avoid electrical shock, plug the power cord into a properly wired
receptacle before connecting to the product input or output terminals. A
protective-ground connection by way of the grounding conductor in the
power cord is essential for safe operation.
Use the Proper Power Cord
Use only the power cord and connector specified for your product. Use only
a power cord that is in good condition. Refer cord and connector changes
to qualified service personnel.
Use the Proper Fuse
To avoid fire hazard, use only the fuse having identical type, voltage rating,
and current rating characteristics. Refer fuse replacement to qualified
service personnel.
Do Not Operate in Explosive
Atmospheres
To avoid explosion, do not operate this product in an explosive
atmosphere.
VSP 1314
User’s Manual
5
Terms In This Manual and Equipment
Marking
WARNING
Highlights an operating procedure, practice, condition,
statement, etc, which, if not strictly observed, could result in
injury or death of personnel.
Note
Highlights an essential operating
procedure,condition or statement.
CAUTION
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
VSP 1314
User’s Manual
6
Change History
The table below lists the changes to the Video Processor User’s Guide.
Format
Time
ECO#
Description
Principal
V1.0
2012-10-12
0000
Release
BIN
VSP 1314
User’s Manual
7
CONTENT
CONTENT .........................................................................................8
1.
Introduction ........................................................................... 12
Chapter Structure ........................................................................... 13
How to Use This Manual ................................................................. 14
Terms and Definitions ...................................................................... 15
System Overview ............................................................................. 20
Application Questions ...................................................................... 21
2.
Hardware Orientation ........................................................... 22
In This Chapter ................................................................................. 22
VSP 1314 Rear Panel...................................................................... 23
INPUT Interface ......................................................................................... 23
1:USB Input ............................................................................................. 23
2~5:CVBS Input ...................................................................................... 24
6.7: VGA Input ........................................................................................... 24
17.18.19:DVI Input ................................................................................. 24
CONT Interface ......................................................................................... 24
8.Dial Switch .............................................................................................. 24
9. 10/100M Interface................................................................................. 24
10. USB Interface ...................................................................................... 24
11.RS232 Interface ................................................................................... 25
VSP 1314
User’s Manual
8
OUTPUT Interface .................................................................................... 25
12.13.22.23: Gigabit copper port............................................................ 25
14.24:Power supply port of Sending Card ......................................... 25
15.25:USB control port of sending card ............................................. 25
16.26:DVI Input ....................................................................................... 25
20:DVI Output ......................................................................................... 25
21:DVI +VGA-DVI Output ..................................................................... 25
Switch and Power ..................................................................................... 26
27.28:Power Interface and Switch ...................................................... 26
VSP 1314 Front Panel ..................................................................... 27
LCD panel ................................................................................................... 28
Menu Buttons ............................................................................................. 28
3.
Hardware Installation ........................................................... 34
In This Chapter ................................................................................. 34
Safety Precautions ........................................................................... 35
Unpacking and Inspection ............................................................... 35
Site Preparation ................................................................................ 35
4.
Menu Orientation .................................................................. 36
In This Chapter ................................................................................. 36
MENU ................................................................................................ 37
MENU---Input ............................................................................................. 39
VSP 1314
User’s Manual
9
MENU---Output.......................................................................................... 39
MENU---Split .............................................................................................. 41
MENU---View ............................................................................................. 42
MENU---USB Setting ................................................................................ 42
MENU---Test Pattern ................................................................................ 42
MENU--- Language ................................................................................... 42
MENU--- System ....................................................................................... 42
MENU--- OLED Luminance..................................................................... 43
MENU--- Video Firmware Update .......................................................... 43
MENU--- Key Pad Lock ............................................................................ 43
MENU---Factory Reset............................................................................. 43
EFFECT---EFFECT Switching ................................................................ 43
5.
System Setup and Operation .............................................. 45
In This Chapter ................................................................................. 45
How to connect equipment.............................................................. 46
How to make equipment normal operation ................................... 48
How to preview input signal source ............................................... 49
How to adjust output resolution ...................................................... 50
How to adjust size and position of image ...................................... 51
How to scale image .......................................................................... 53
How to switch signal of single image ............................................. 55
How to set picture in picture ............................................................ 56
VSP 1314
User’s Manual
10
How to select switching effect ......................................................... 57
How to set input matrix .................................................................... 59
How to set DVI3 as background ..................................................... 60
How to splicing with DVI3 ................................................................ 62
How to use BLACK .......................................................................... 65
How to use Test Pattern .................................................................. 66
How to save parameter ................................................................... 67
How to load parameter .................................................................... 68
A.Specification .............................................................................. 69
B.Contact Information ..................................................................71
C.Firmware Upgrade ..................................................................... 72
Function Firmware Upgrade ........................................................... 72
Image Firmware Upgrade ............................................................... 74
Communication Firemware Upgrade ............................................. 75
VSP 1314
User’s Manual
11
1. Introduction
This chapter is designed to introduce you to the VSP 1314 User’s Manual.
Areas to be covered are:

Chapter Structure

How to use this manual

Tems and Definitions

System Overview

Application Questions
VSP 1314
User’s Manual
12
1.Introduction
Chapter Structure
Chapter Structure
The following chapters provide instructions for all aspects of VSP1314
operations.
Chapter 1
Introduction
Chapter 2
Hardware Orientation
Chapter 3
Hardware Installation
Chapter 4
Menu Orientation
Chapter 5
System Setup and Opetations
Appendix A
Specification
AppendixB
Contact information
AppendixC
Firmware Upgrade
VSP 1314
User’s Manual
13
1.Introduction
How to Use This Manual
How to Use This Manual
Following are important tips for streamlining your use of this User’s Manual
in its electronic ―PDF form.
Navigating
Use Acrobat Reader’s ―bookmarks to navigate to the desired location. All
chapter files have the same bookmark structure for instant navigation to
any section. Please note:
 Extensive hyperlinks are provided within the chapters.
 Use Acrobat’s ―Go to Previous View‖and ―Return to next
View‖buttons to trace your complete navigational path.
 Use the ―Previous Page‖ and ―Next Page‖buttons to go to
te previous or next page within a file.
 Use Acrobat’s extensive search capabilities,such as the ―Find‖tool and
―Search lndex‖tool to perform comprehensive searches as required.
Table of Contents and Index
Use the Table of Contents bookmarks to navigate a desired topic.
Click any item to instantly jump to that section of the guide. You can
also use the Index to jump to specific topics within a chapter. Each
page number in the Index is a hyperlink.
General Operations
To ensure trouble-free operation, please follow all procedures as listed
below:
 For detailed installation instructions,refer to chapter 3 ―Hardware
Installation‖on page34.
 For communication software control guide,refer to Chapter 5,
―Communication Software Control Guide‖ on page 45.
Should you have any questions regarding the installation or operation of
VSP 1314, please consult with the factory. Refer to Appendix C, ―
Upgrading Software on page 72 for contact information.
VSP 1314
User’s Manual
14
1.Introduction
Terms and Definitions
Terms and Definitions
The following terms and definitions are used throughout this guide.
 “ASCII”: American Standard for Information Interchange. The standard
code consisting of 7-bit coded characters (8 bits including parity check)
used to exchange information between data processing systems, data
communication systems, and associated equipment. The ASCII set
contains control characters and graphic characters.
 “Aspect ratio”: The relationship of the horizontal dimension to the
vertical dimension of an image. In viewing screens, standard TV is 4:3,
or 1.33:1; HDTV is 16:9, or 1.78:1. Sometimes the ―:1 is implicit,
making TV = 1.33 and HDTV = 1.78.
 “AV”: Audio visual, or audio video.

A “Background” is an unscaled source, typically originating from a
computer. Abackground source appears at the system’s lowest priority
— visually in back of all other sources.
 “Baudrate”:Named of J.M.E. Baudot, the inventor of the Baudot
telegraph code. The number of the electrical oscillations per second,
called baud rate. Related to, but not the same as, transfer rate in bits
per second (bps).
 “Blackburst”: The video waveform without the video elements. It
includes the vertical sync, horizontal sync, and the chroma burst
information. Blackburst is used to synchronize video equipment to
align the video output. One signal is normally used to set up an entire
video system or facility. Sometimes it is called House sync.
 “BNC”: Bayonet Neill-Concelman. A cable connector used extensively
in television and named for its inventors. A cylindrical bayonet
connector that operates with a twist-locking motion. To make the
connection, align the two curved grooves in the collar of the male
connector with the two projections on the outside of the female collar,
push, and twist. This allows the connector to lock into place without
tools.
 “light upness”: Usually refers to the amount or intensity of video light
produced on a screen without regard to color. Sometimes
called ―black level.

“CAT 5”: Category 5. Describes the network cabling standard that
consists of four unshielded twisted pairs of copper wire terminated by
RJ-45 connectors. CAT 5 cabling supports data rates up to 100 Mbps.
CAT 5 is based on the EIA/TIA 568 Commercial Building
Telecommunications Wiring Standard.
 “Color bars”: A standard test pattern of several basic colors (white,
yellow, cyan, green, magenta, red, blue, and black) as a reference for
system alignment and testing. In NTSC video, the most commonly
used color bars are the SMPTE standard color bars. In PAL video, the
VSP 1314
User’s Manual
15
1.Introduction
Terms and Definitions
most commonly used color bars are eight full field bars. In the
computer, the most commonly used color bars are two rows of
reversed color bars.
 “Color burst”: In color TV systems, a burst of subcarrier frequency
located on the back porch of the composite video signal. This serves
as a color synchronizing signal to establish a frequency and phase
reference for the chroma signal. Color burst is 3.58 MHz for NTSC and
4.43 MHz for PAL.
 “Color temperature”: The color quality, expressed in degrees
Kelvin(K), of a light source. The higher the color temperature, the bluer
the light. The lower the temperature, the redder the light. Benchmark
color temperature for the A/V industry include 5000°K, 6500°K, and
9000°K.

“Contrast ratio”: The radio of the high light output level divided by the
low light output level. In theory, the contrast radio of the television
system should be at least 100:1, if not 300:1. In reality, there are
several limitations. In the CRT, light from adjacent elements
contaminate the area of each element. Room ambient light will
contaminate the light emitted from the CRT. Well-controlled viewing
conditions should yield a practical contrast ratio of 30:1 to 50:1.

“DVI”: Digital Visual Interface. The digital video connectivity standard
that was developed by DDWG (Digital Display Work Group). This
connection standard offers two different connectors: one with 24 pins
that handles digital video signals only, and one with 29 pins that
handles both digital and analog video.

“EDID”: Extended Display Identification Data – EDID is a data
structure used to communicate video display information, including
native resolution and vertical interval refresh rate requirements, to a
source device. The source device will then output the optimal video
format for the display based on the provided EDID data, ensuring
proper video image quality. This communication takes place over the
DDC – Display Data Channel.

“Ethernet”: A Local Area Network (LAN) standard officially known as
IEEE 802.3. Ethernet and other LAN technologies are used for
interconnecting computers, printers, workstations, terminals, servers,
etc. within the same building or campus. Ethernet operates over
twisted pair and over coaxial cable at speeds starting at 10Mbps. For
LAN interconnectivity, Ethernet is physical link and data link protocol
reflecting the two lowest layers of the OSI Reference Model.

“Frame”: In interlaced video, a frame is one complete picture. A video
frame is made up of two fields, or two sets of interlaced lines. In a film,
a frame is one still picture of a series that makes up a motion picture.

“Gamma”: The light output of a CRT is not linear with respect to the
voltage input. The difference between what you should have and what
is actually output is known as gamma.

“HDMI” - High – Definition Multimedia Interface: An interface used
VSP 1314
User’s Manual
16
1.Introduction
Terms and Definitions
primarily in consumer electronics for the transmission of
uncompressed high definition video, up to 8 channels of audio, and
control signals, over a single cable. HDMI is the de facto standard for
HDTV displays, Blu-ray Disc players, and other HDTV electronics.
Introduced in 2003, the HDMI specification has gone through several
revisions.

“HDSDI”: The high-definition version of SDI specified in
SMPTE-292M. This signal standard transmits audio and video with 10
bit depth and 4:2:2 color quantization over a single coaxial cable with a
data rate of 1.485 Gbit/second. Multiple video resolutions exists
including progressive 1280x720 and interlaced 1920x1080 resolution.
Up to 32 audio signals are carried in the ancillary data.

“JPEG” (Joint photographic Expects Group): Commonly used method
of lossy compression for photographic images using a discreet cosine
transfer function. The degree of compression can be adjusted,
allowing a selectable tradeoff between storage size and image quality.
JPEG typically achieves 10:1 compression with little perceptible loss in
image quality. Produces blocking artifacts.

“MPEG”: Motion Picture Expect Group. A standard committee under
the auspices of the International Standards Organization working on
algorithm standards that allow digital compression, storage and
transmission of moving image information such as motion video,
CD-quality audio, and control data at CD-ROM bandwidth. The MPEG
algorithm provides inter-frame compression of video images and can
have an effective compression rate of 100:1 to 200:1.

“NTSC”: The color video standard used in North America and some
other parts of the world created by the National Television Standards
Committee in the 1950s. A color signal must be compatible with
black-and-white TV sets. NTSC utilizes an interlaced video signals,
525 lines of resolution with a refresh rate of 60 fields per second (60
Hz). Each frame is comprised of two fields of 262.5 lines each, running
at an effective rate of 30 frames per second.

“PAL”: Phase Alternate Line. A television standard in which the phase
of the color carrier is alternated from line to line. It takes four full
pictures (8 fields) for the color-to-horizontal phase relationship to
return to the reference point. This alternation helps cancel out phase
errors. For this reason, the hue control is not needed on a PAL TV set.
PAL, in many transmission forms, is widely used in Western Europe,
Australia, Africa, the Middle East, and Micronesia. PAL uses 625-line,
50-filed (25 fps) composite color transmission system.

“Operator”: Refers to the person who uses the system.

“PIP”: Picture-in-Picture. A small picture within a larger picture created
by scaling down one of the images to make it smaller. Each picture
requires a separate video source such as a camera, VCR, or computer.
Other forms of PIP displays include Picture-by-Picture (PBP) and
Picture-with-Picture (PWP), which are commonly used with 16:9
aspect display devices. PBP and PWP image formats require a
separate scaler for each video window.
VSP 1314
User’s Manual
17
1.Introduction
Terms and Definitions

“Polarity”: The positive and negative orientation of a signal. Polarity
usually refers to the direction or a level with respect to a reference (e.g.
positive sync polarity means that sync occurs when the signal is going
in the positive direction).

“RJ-45”: Registered Jack-45. A connector similar to a telephone
connector that holds up to eight wires, used for connecting Ethernet
devices.

“RS-232”: An Electronic Industries Association (EIA) serial digital
interface standard specifying the characteristics of the communication
path between two devices using either DB-9 or DB-25 connectors.
This standard is used for relatively short-range communication and
does not specify balanced control lines. RS-232 is a serial control
standard with a set number of conductors, data rate, word length, and
type of connector to be used. The standard specifies component
connection standards with regard to the computer interface. It is also
called RS-232-C, which is the third version of the RS-232 standard,
and is functionally identical to the CCITT V.24 standard.

“Saturation”: Chroma, chroma gain. The intensity of the color, or the
extent to which a given color in any image is free from white. The less
white in a color, the truer the color or the greater its saturation. On a
display device, the color control adjusts the saturation. Not to be
confused with the light upness, saturation is the amount of pigment in
a color, and not the intensity. Low saturation is like adding white to the
color. For example, a low-saturated red looks pink.

“Scaling”: A conversion of a video or computer graphic signal from a
starting resolution to a new resolution. Scaling from one resolution to
another is typically done to optimize the signal for input to an image
processor, transmission path or to improve its quality when presented
on a particular display.

“SDI”: Serial Digital Interface. The standard based on a 270 Mbps
transfer rate. This is a 10-bit, scrambled, polarity independent interface
with common scrambling for both component ITU-R 601 and
composite digital video and four channels of (embedded) digital audio.

“Seamless Switching”: A feature found on many Extron video
switchers. This feature causes the switcher to wait until the vertical
interval to switch. This avoid a glitch (temporary scrambling) which
normally is seen when switching between sources.

“SMPTE”: Society of Motion Picture and Television Engineers. A
global organization, based in the United States, that sets standards for
baseband visual communications. This includes film as well as video
and television standards.

“S-video”: A composite video signal separated into the luma (―Y‖ is
for luma, or black and white information; light upness) and the chroma
(―C‖ is an abbreviation for chroma, or color information).

“Sync”: Synchronization. In video, sync is a means of controlling the
timing of an event with respect to other events. This is accomplished
with timing pulses to insure that each step in a process occurs at the
VSP 1314
User’s Manual
18
1.Introduction
Terms and Definitions
correct time. For example, horizontal sync determines exactly when to
begin each horizontal scan line. Vertical sync determines when the
image is to be refreshed to start a new field or frame. There are many
other types of sync in video system.(Also known as ―sync signal‖
or ―sync pulse.‖)

“TCP/IP”: Transmission Control Protocol/Internet Protocol. The
communication protocol of the Internet. Computers and devices with
direct access to the Internet are provided with a copy of the TCP/IP
program to allow them to send and receive information in an
understandable form.

“USB”: Universal Serial Bus. USB was developed by seven PC and
telecom industry leaders (Compaq, DEC, IBM, Intel, Microsoft, NEC,
and Northern Telecom). The goal was easy plug-and-play expansion
outside the box, requiring no additional circuit cards. Up to 127
external computer devices may be added through a USB hub, which
may be conveniently located in a keyboard or monitor. USB devices
can be attached or detached without removing computer power. The
number of devices being designed for USB continues to grow, from
keyboards, mice, and printers to scanners, digital cameras, and ZIP
drives.

“VESA”: Video Electronics Standards Association. A nonprofit number
organization dedicated to facilitating and promoting personal computer
graphics through improved standards for the benefit of the end-user.
www.vesa.org

“VGA”: Video Graphics Array. Introduced by IBM in 1987, VGA is an
analog signal with TTL level separate horizontal and vertical sync. The
video outputs to a 15-pin HD connector and has a horizontal scan
frequency of 31.5 kHz and vertical frequency of 70 Hz (Mode 1, 2) and
60 Hz (Mode 3). The signal is non-interlaced in modes 1, 2, and 3 and
interlaced when using the 8514/A card (35.5 kHz, 86 Hz) in mode 4. It
has a pixel by line resolution of 640×480 with a color palette of 16 bits
and 256,000 colors.

“YCrCb”: Used to describe the color space for interlaced component
video.

“YPbPr”: Used to describe the color space for progressive-scan
(non-interlaced) component video.
VSP 1314
User’s Manual
19
1.Introduction
System Overview
System Overview
The VSP 1314 is a 3 layers seamless switcher and scale that accepts a
wide variety of video signals,including RGB computer-video, HDTV, which
support 4 composite (CVBS),2 VGA, 2 DVI (compatible with HDMI1.3),2
USB inputs and 2 DVI3(background window). It combines truly seamless,
glitch-free switching with advanced scaling technology to meet the
requirement of high quality,high resolution video presentation.Use the
switching transition effects can offer a wide range of effects,such ad full
screen,dissolves and wipes with selectable durations as well as a cutt,the
video transition effect is only enable for the program output .Numerous
seamless
transition
effects,triple
windows
operation,variety
user
configuration,pixel-to-pixel,multiple save memory and remote control ways
for integration,VSP1314 is designed to deliver advanced capabilities to
high-end presentation environments.The VSP 1314 uses two editable input
structures,one is CV1,CV2,VGA1,DVI1 and USB1 input,and the other is
CV3,CV4,VGA2,DVI2 and USB2 input ,it can process each input and
monitor the image as well as the preview output ,user can send each input
to preview monitor ,and after confirm,take the input to program output.
VSP1314 offers three outputs,each can be set as program output or
preview output and connect to the back end display system,including
projector,LED display and conference system.The VSP 1314 is available
to be controlled from the local color panel as well as through remote
RS232,USB and Ethernet control.Local color panel matches green light
(in the broadcast), yellow light(tobe broadcast), red light(optional
broadcast),and highlight OLED panel .Further more,presentation can be
managed by using the RGBlink VSP1314 Window based software.
VSP 1314
User’s Manual
20
1.Introduction
Application Questions
Application Questions
RGBlink offers solutions to demanding technical problems. Any application
questions, or required further information, please contact with our
Customer Support Engineers. Refer to Appendix B for contact details.
VSP 1314
User’s Manual
21
2. Hardware Orientation
In This Chapter
This chapter provides detailed information about the VSP 1314 hardware.
The following topics are discussed:

VSP 1314 Rear Panel

VSP 1314 Front Panel
VSP 1314
User’s Manual
22
2.Hardware Orientation
VSP 1314 Rear Panel
VSP 1314 Rear Panel
This chapter provides detailed information about the VSP 1314 hardware.
The following topics are discussed:
NO.
INTERFACE
NO.
INTERFACE
1
USB Input
12.13.21.23
Gigabit copper port
2~5
CVBS Input
14.24
Power supply port of
Sending card
6. 7
VGA Input
15.25
USB control port of
sending card
8
Dial Switch
16~19.26
DVI Input
9
10/100M Interface
20.21
DVI Input
10
USB Interface
27
Power
11
RS232 Interface
28
Switch
INPUT Interface
Including 2 USB input, 4 composite input(CVBS), 2 VGA input DB15
interface, 3 DVI-I interface,compatible with HDMI input, and 1 DVI-I
interface(18)is background input or splicing input.
1:USB Input
USB 1/2 media player input interface, can access USB device or mobile
hard disk with USB storage function. Support image format: JPGE, BMP,
PNG; and support video format: MP4, MPEG1, MPEG2, RMVB, MJPG.Can
used to upgrade firmware.
VSP 1314
User’s Manual
23
2.Hardware Orientation
VSP 1314 Rear Panel
2~5:CVBS Input
CVBS 1/2/3/4 input. Can receive standard video signal from players,
cameras etc. Input supported resolution 480i and 576i via BNC. Supported
standards include: PAL, NTSC and SECAM.
6.7: VGA Input
VGA 6/7 Input Interface, input the video signal from HD player and
Computer, etc. Compatible with YPbPr signal, input signal via the DB9
interface.
17.18.19:DVI Input
DVI 17/18 input. Can receive video signal from HD player, DVD, Computer
video signal via DVI connector, input supported resolution:
1080P50/59.94/60,1080i50/59.94/60, 720p50/59.94/60;PAL;NTSC,
VESA:1024×768×60Hz,1280×768×60Hz,1280×1024×60Hz,
1440×900×60Hz,1680×1050×60Hz,1600×1200×60Hz,
1920×1080×60Hz;
DVI 19 input interface. Background signal interface(DVI).Can receive video
signal from laptop,computer,input signal via DVI interface;(Only can input
DVI signal of standard computer graphics.
CONT Interface
8.Dial Switch
General use for 100M control panel,when the dial switch are down it means
is in uptade station
9. 10/100M Interface
10. USB Interface
Remote communication device control interface, used to connect the
computer.
VSP 1314
User’s Manual
24
2.Hardware Orientation
VSP 1314 Rear Panel
11.RS232 Interface
Used to connect the computer.
OUTPUT Interface
12.13.22.23: Gigabit copper port
Gigabit copper port, connect to LED screen.
14.24:Power supply port of Sending Card
Power has been already supplied by video processor itself, don’t need
external power supply.
15.25:USB control port of sending card
16.26:DVI Input
Input the DVI out originating from other video processors. (This DVI
connector does not support hot-plugging)
20:DVI Output
Connect to the monitor or LED screen which has DVI interface(This DVI
connector does not support hot-plugging).
21:DVI +VGA-DVI Output
Connect to the monitor or LED screen which has DVI interface.(This DVI
connector does not support hot-plugging).
DVI +VGA , VGA output connector can be connected to monitor or
projector which has VGA interface.
Note
Via
adapter,can connect with
DVI-based or VGA-based equipment, and via,
DVI to VGA adapter, can output VGA
only.
VSP 1314
User’s Manual
25
2.Hardware Orientation
VSP 1314 Rear Panel
Switch and Power
27.28:Power Interface and Switch
AC 90-264V 3.8A 50/60Hz IEC-3 Power Interface
VSP 1314
User’s Manual
26
2.Hardware Orientation
VSP 1314 Front Panel
VSP 1314 Front Panel
Insert power cord and push power to ON position. LCD module on the front
panel will show RGBLINK and go into self verification before it load last
setting config and send processed image to the target monitor. For the first
setup, DVI input is default source. With front panel keyboard, user can
operate VSP 1314 through the menus on LCD panel.
VSP 1314 front panel as shown in figure:
AVDSP Series VSP 1314
Seamless Switcher & Scaler
System Initializing 100%
CH1:DVI1 NO INPUT
CH2:DVI2 NO INPUT
3
Output:
1
A
F
V1
V2
1024X768 60Hz
When startup the system,it will enter to menu,and will refresh LCD module
menu display state automatically every 2 minutes.display content are input
signal information and format,output format,etc on default settings.
VSP 1314
User’s Manual
27
2.Hardware Orientation
VSP 1314 Front Panel
VSP 1314 front panel as following:
LCD panel
Used to show the key and communication interactive menu.
Menu Buttons
Color operation panel:
Green light means on work;
Red light means optional choice for work;
MENU/EFFECT:Menu and Effect function multiplexing button;
Press it and light up green to enter to Menu function,the LCD panel shows
content of MENU,rotate and press the adjust knob select MENU.Press
again to reback the last Menu. LCD panel shows as following:
Input
Output
Split
View
Detail please refer to Manu Orientation.
Press button and light up red to enter to EFFECT function,LCD panel
shows the menu of EFFECT.rotate the adjust knob and press to select the
EFFECT Mode,LCD showss as following:
Effects
*Effectsn Mode:<FADE>
Display Time:<1.5S>
VSP 1314
User’s Manual
28
2.Hardware Orientation
VSP 1314 Front Panel
Detail please refer to How to select switching effect.
PIP1/PIP2:PIP mode multiplexing button;
Press button and light up green,that means is1/2 mode;layer 1 above
layer2;
Press button and light up red,that means is 2/1 mode;layer 2 above layer1
LCD showss as following:
PIP A/B
Detail please refer to How to set picture in picture.
SAVE/LOAD:SAVE and LOAD muitiplexing button;
Press button and light up green to enter to Save mode,at the same time
CV1/1, CV2/2, USB1/3, DVI1/4, VGA1/5, CV3/6, CV4/7, USB2/8, DVI2/9,
VGA 2/10 all of them light up green ,The figure :1,2,3,4,5,6,7,8,
9,10,down of the button also light up green,It means you can press
arbitrary button to save.And the LCD panel will show Save Sucess after
finish saving.And all the button will recover to its original state.
LCD showss as following:
Save:
Press<1~10>to Save
Detail please refer to How to save parameter.
Press button and light up red to enter to LOAD mode,at the same time
CV1/1, CV2/2, USB1/3, DVI1/4, VGA1/5, CV3/6, CV4/7, USB2/8, DVI2/9,
VGA 2/10 all of them light up red ,the figure of 1,2,3,4,5,6,7,8,
9,10under button is load save1~10,press arbitrary button1~10 to load
VSP 1314
User’s Manual
29
2.Hardware Orientation
VSP 1314 Front Panel
save.LCD will show Load From,after finish loading, the button which
selected will light out,and other 9 lights light up still.It means can load other
infomation .Press button again the red light light out it means have exit
Load mode.
LCD shows as following:
Load From:
Press<1~10>to Load
Detail please refer toHow to load parameter
SCALE/CROP:SCALE and CROP setting muitiplexing button
Press button,light up green to enter to SCALE mode;
Press button,light up red to enter to CROP mode;
H SIZE/H POS:Height and vertical position setting muitiplexing button;
Press button,light up green to enter to height setting;
Press button,light up red to enter to vertical position setting;
V SIZE/V POS:Width and transverse position setting muitiplexing button;
Press button,light up green to enter to width setting;
Press button,light up red to enter to transverse position setting;
Three key combination use as following:
SCALE:
Press SCALE/CROP,light up green to enter to Scale setting;At the same
time H SIZE\H POS light up green,rotate the adjust knob can adjust the
hight of picture;Press H SIZE\H POS ,light up red to enter to light-vertical
position setting,rotate the adjust knob can adjust the position of
veitical;Press V SIZE/V POS ,light up green to enter to Width setting,rotate
VSP 1314
User’s Manual
30
2.Hardware Orientation
VSP 1314 Front Panel
the adjust knob,can adjust width of picture;Press V SIZE/V POS,light up
red to enter to transverse position setting,rotate the adjust knob can adjust
the positon of transverse;
LCD shows as following:
DVI2
Scale HSize
Scale HPos
Scale VSize
Scale VPos
<1024>
< 0>
< 768>
< 0>
CROP:
Press SCALE/CROP,light up red to enter to scale setting;At the same time
when H SIZE\H POS light up green to enter to height setting,rotate the
adjust knob can adjuest the height percentage;Press H SIZE\H POS,light
up red to enter to vertical position setting,rotate the adjust knob,can adjuest
the veritical percentage;PressV SIZE/V POS,light up green to enter to
width setting,rotate the adjust knob can adjust the width percentage;Press
V SIZE/V POS ,light up red to enter to transverse position setting,rotate the
adjust knob can adjuest the transverse positon percentage;
Note
The percentage of CROP is the curren output
resolution percentage,after scale set full
screen.Such as resolution is: 1024x768,set
width as 50,set transverse position as 0,height
as 50,set certical position as 0.That is scale
the 1/4 picture of full screen at the top right
corner as 1024x768 output。
LCD shows as following:
DVI2
VSP 1314
Crop HSize
Crop HPos
Crop VSize
Crop VPos
< 100>
< 50>
< 100>
< 50>
User’s Manual
31
2.Hardware Orientation
VSP 1314 Front Panel
The color of signal button:
Green light means signal output to program ;
Yellow light means signal output to preview;
Red light means can switch signal at preview;
CV1/1:CV1 signal source and SAVE 1 and Load 1 muitiplexing button;
CV2/2:CV2 signal source and SAVE 2and Load 2 muitiplexing button;
USB1/3:USB1signal source and Save 3 and Load 3 muitiplexing button;
DVI1/4:DVI1signal source and Save 4 and Load 4 muitiplexing button;
VGA1/5:VGA1signal source and Save 5 and Load 5 muitiplexing button;
CV3/6: CV3 signal source and Save 6 and Load 6 muitiplexing button;
CV4/7:CV4 signal source and Save 7 and Load 7 muitiplexing button;
VSP 1314
User’s Manual
32
2.Hardware Orientation
VSP 1314 Front Panel
USB2/8:USB2 signal source and Save 8 and Load 8 muitiplexing button;
DVI2/9:DVI2 signal source and Save 9 and Load 9 muitiplexing button;
VGA2/10:VGA2 signal source and Save 10 and Load 10 muitiplexing
button;
DVI3/BLACK:DVI3 signal source and BLACK muitiplexing button;
Detail please refer to How to set DVI3 as background
Detail please refer to How to splicing with DVI3
Detail please refer to How to use BLACK
TAKE:Seamless Switching button
Press button to switch Preview to Prigram;
VSP 1314
User’s Manual
33
3. Hardware Installation
In This Chapter
This chapter provides comprehensive installation instruction for VSP 1314
hardware: Following is the size of VSP 1314 for your reference.
VSP 1314
User’s Manual
34
Safety Precautions
For all VSP 1314 processor installation procedures, please observe the
following important safety and handling rules to avoid damage to yourself
and the equipment.
 To protect users from electric shock, ensure that the chassis connects
to earth via the ground wire provided in the AC power Cord.
 The AC Socket-outlet should be installed near the equipment and be
easily accessible.
Unpacking and Inspection
Before opening VSP 1314 process shipping box, inspect it for damage. If
you find any damage, notify the shipping carrier immediately for all claims
adjustments. As you open the box, compare its contents against the
packing slip. If you find any shortages, contact your sales representative.
Once you have removed all the components from their packaging and
checked that all the listed components are present, visually inspect the
system to ensure there was no damage during shipping. If there is damage,
notify the shipping carrier immediately for all claims adjustments.
Site Preparation
The environment in which you install your VSP1314 should be clean,
properly lit, free from static, and have adequate power, ventilation, and
space for all components.
VSP 1314
User’s Manual
35
4. Menu Orientation
In This Chapter
This chapter describes all VSP 1314 processor menus, including how they
are accessed, the functions that are available, and descriptions of each
menu tree (in block diagram format).
The following topics are discussed:
• MENU

Input

Output

Split

View

USB Setting

Test Pattern

Language

System

OLED Luminace

Video Firmware Update

Key Pad Lock

Factory Reset
• EFFECT
VSP 1314
User’s Manual
36
4.Menu Orientation
MENU
MENU
Press MENU/EFFECT, button light up green light,that is you can enter the
main menu,as following:
rotate the adjust knob can select the up and down menuitem;When the
munuitem added to a blue bar ,it means is in a selecred state,press knob to
make sure and enter to the corresponding menu to set or view.
Picture 1:
VSP 1314
User’s Manual
37
4.Menu Orientation
MENU
Picture 2:
VSP 1314
User’s Manual
38
4.Menu Orientation
MENU
MENU---Input
Press MENU/EFFECT ,it light up green to enter to MENU and rotate the
adjust knob to select Input and press to make sure.LCD panel show the
information of input resolution and input matrix ;As picture above,If user
need to change input signal source ,rotate the adjust knob to select the
matrix,press knob can enter the corresponding channel setting;Channel 1
and Channel 2 can input 1 or input 2,Channel 3 can select test picture or
input DVI3.
MENU---Output
Press MENU/EFFECT,it light up green to enter to MENU,and rotate the
adjust knob to select the Output,press to make sure,now can set the
following options respectively,as picture 1:
Output resolution:Select this option user can select output resolution
according need,current support 12 kinds of resolution ,were as following:
1024x768_60Hz,1280x768_60 Hz,1280x720_60 Hz,1280x1024_60 Hz,
1366x768_60 Hz,1400x1050_60 Hz,1440x900_60 Hz, 1440x900_60_r Hz,
1600x1200_60 Hz,1680x1050_60 Hz,1920x1080_60 Hz,1920x1200_60
Hz.
Detail please refer to How to adjust output resolution.
Output corrention:For DVI1 or DVI2 can set DE and can select coding
format of output signal(can select HDMI or DVI),And also can adjust color
range of video and image also can select the polarity of Horizontal and
vertical.
Select DE,press knob to set corresponding submenu, first of all to set DE
Setup switch;rotate the adjust knob to select ON ,then press the knob to
make sure and enter to DE setting,can up or down of menu:
DE H Start: Abscissa setting;DE V Start: Ordinate setting;
DE Width:Width setting;DE Height:Height setting;
VSP 1314
User’s Manual
39
4.Menu Orientation
MENU
When input signal to the large screen,boundary appear black side,can use
this function to adjust to make full screen display.
Select
DVI1,rotate
the
adjust
knob
can
choice
the
HDMI/DVI
interface,Default interface is DVI output.If you need HDMI output,please
select HDMI.
Select DVI1 also can choice color format,Color range of video format is
16-235,Color range of image format is 0-255.
The same method can be applied to set the DVI2 output.
Screen setting:(Including above setting):
Screen Pos X:Horizontal coordinate setting;
Screen Pos Y:Vertical coordinate setting;
Screen Width:Width setting;
Screen Height:Height setting;
Window Mode:Can switch between Screen Full .
User can use USB1~USB4 to upgrade firmware.
Output ratio:Proportional setting menu:
Normal ;4:3 aspect ratio;16:9 aspect ratio,rotate the adjust knob can
switch between aspect ratio;
Image adjustment:
light upness:Can change the light upness of the image;
Contrast:Can change the color contrast of image;
Saturation:Can change the color temperature value of image;
Color Red :Can change the red of image;
Color Green:Can change the green of image;
Color Blue:Can change the blue of image;
User can adjust and set according to actual condition,This function mainly
suitable for professional to operate image quality. Nonprofessional don’t
recommend to operate obove setting.If image quality were distortion
because of improper operation,can reply the factory setting.
VSP 1314
User’s Manual
40
4.Menu Orientation
MENU
In addition need to adjust the numerical range at 0~174,other at 0~255.
Background: rotate the adjust knob can choice the background,TP is
Test Picture,DVI3 is Background input .
Note
Background resolution of image is the same with
output resolution;
Detail please refer to How to set DVI3 as background.
Matrix:
VSP1314 with output programmable matrix function,That is can copy
random channel at one channel,means can output Program or Preview
arbitrarilly:can output DVI1 or DVI2 or VGA arbitrarilly.That is every port
can set as program or preview:DVI1 output also can set Preview
output,DVI2 or VGA also can set Program output.The defference between
Program and Preview is the Preview picture have effect switching
mode,and the Program just have cut switching mode.
Detail please refer to How to set Input matrix.
Layer setting:Can close and open layer of channel 1 or channel 2.And
can close SCALE when the input signal source less than 289, that can
reduce image appear flowers screen probability.
Signal Backup:If open the Signal Bacgup,equipment will search other
signal source automatically as Program output of the same channel when
Program signal snapped, to make large screen do not appear black
screen;But if there are no input signal source of the same chanel,will
appear black screen.
MENU---Split
VSP1314 also can work as seamless splicing unit,use DVI3 to as splicing
unit input signal,support horizontally splicing or vertical splicing;
Detail please refer to How to splicing with DVI3
VSP 1314
User’s Manual
41
4.Menu Orientation
MENU
MENU---View
Delay Call Save: Set delay the output time,When more than one equiment
power on,and the processor is the end equipment in order to improve
question that can’t identify the input signal and phenomenon that LED
screen appear messy code and flash screen,now need to delay the input
time.
MENU---USB Setting
USB Photo Play Time;Use this when you need play photo for o long time.
USB Play Type,picture and video mode be selected by user,USB can’t play
picture and video at the same time.
USB Play State:Can set playing or stoping mode.
MENU---Test Pattern
Automatic color change test,enter can set the automatic change
time;Manual color change test,enter can set RGB and 6 kinds of rollong
test picture,2 kinds of striped test picture,2 kinds of gray scale test
picture.Detail menu of TP as Picture2.
Detail please refer to How to Test Pattern
MENU--- Language
Enter LANGUAGE :Can select English or Chinese.
MENU--- System
System information:
SN:The serial number of this processor, you can check the product
information according this number;
MCU VER:Version information of MCU;
FPAG VER:Version information of FPGA;
IP:Information of IP;
Video Firmware VER:Version information of Video Firmware;
VSP 1314
User’s Manual
42
4.Menu Orientation
MENU
Authorized setting:This product have been useing time limited by our
company,if it is service life and need to continue to use,you must to contact
with our sales or service to get the password.
State:Authorized and unauthorized;
MENU--- OLED Luminance
Enter can set the luminance of font;
MENU--- Video Firmware Update
User can update video firmware via USB1~USB4.
MENU--- Key Pad Lock
Enter can set whether key pad lock;If open it,operating other buttons are
invalid;release it, shall also press < Menu > and < Take > key to
unlock!This function mainly in order to prevent the user misoperation.
MENU---Factory Reset
Select it, press the knob to reset factory;It will show Factory Reset Finish if
success.As picture2;
EFFECT---EFFECT Switching
Press MENU/EFFECT to enter to EFFECT if light up red ;Press the adjust
knob can set EFFECT;There are:Fade in Fde out ,CUT,Wipe Hard,Wipe
Soft Wipe Hard and Wipe Soft have 7 kinds of seamless switching
mode:Wipe Left、Wipe Right、Wipe Up、Wipe Down、Wipe Center Out、
Wipe Curtain Out、Wipe Plus Out;But only Wipe Soft have soft effect;
Cut :Cut Left、Cut Right、Cut Down、Cut Up、Cut Square、Cut Curtain、
Cut Center.It also supports the user defined switching speed;Adjustment
value range is ―0.5 s-30.0 s‖
Detail please refer to
VSP 1314
User’s Manual
43
4.Menu Orientation
MENU
VSP 1314
User’s Manual
44
5. System Setup and Operation
In This Chapter
This chapter provides detailed information about the control
communication software. The following topics are discussed:

How to connect equipment

How to make equipment normal operation

How to preview input signal source

How to adjust output resolution

How to adjust size and position of image

How to scale image

How to switch signal of single image

How to set picture in picture

How to select switch effect

How to set input matrix

How to set DVI3 as background

How to splicing with DVI3

How to use BlACK

How to use Test Pattern

How to save parameter

How to load parameter
VSP 1314
User’s Manual
45
5.System Setup and Operation
How to connect equipment
How to connect equipment
NO
INTERFACE
NO
INTERFACE
1
USB Input Interface
12.13.21.23
Gigabit nets connector
2~5
CVBS Input Interface
14.24
Send card power source
6. 7
VGA Input Interface
15.25
Send card USB control
connector
8
Dial Switch
16~19.26
DVI Input Interface
9
10/100M Interface
20.21
DVI Input Interface
10
USB Interface
27
Power
11
RS232 Control Interface
28
Switch
20.System default DVI1 output as program output,main connect sending
card of larg screen,VSP1314 suppor resolution as following :
1 024x768_60Hz,1280x768_60 Hz,
1280x720_60 Hz,1280x1024_60 Hz,
1366x768_60 Hz,1400x1050_60 Hz,1440x900_60 Hz, 1440x900_60_r Hz,
1600x1200_60 Hz,1680x1050_60 Hz,1920x1080_60 Hz,1920x1200_60
Hz.
Note
Select output resolution via MENU
OUTPUT
OUTPUT
FORMAT.
21. System default DVI2+VGA output interface as preview output,Preview
output signal before output via displayer. Output signal is DVI video signal
and VGA video signal,can connect display that with DVI or VGA interface to
VSP 1314
User’s Manual
46
5.System Setup and Operation
How to connect equipment
preview signal.Output signal via DVI-I interface(Preview adopt standard
DVI-I interface,compatible with VGA output,switch VGA output via
terminil.)Support output resolution:
1024x768_60Hz,1280x768_60 Hz,
1280x720_60 Hz,1280x1024_60 Hz,1366x768_60 Hz,1400x1050_60
Hz,1440x900_60 Hz, 1440x900_60_r Hz, 1600x1200_60
Hz,1680x1050_60 Hz,1920x1080_60 Hz,1920x1200_60 Hz。
Note
Set DVI1,DVI2,VGA as program ouput or
preview output via MENU
OUTPUT
Matrix
In addition to CONT and send card and power interface,others are signal
input interface,DVI(DVI-I Interface) can connect DVI output of computer
and can connect HDMI output of computer or HDMI output of DVD via
DVI-HDMI cable;
VGA(DB15 Interface)can connect VGA ouput of computer or YPBPR of
DVD via VGA-YPBPR;
CVBS(BNC Interface)can connect composite video output of DVD or
composite video output of VCR via RCA-BNC cable;
USB ( USB-A Interface ) can connect USB or mobile HDD with
USB.Support image format :JPGE,BMP,PNG ;Support video format:
MP4, MPEG1, MPEG2, RMVB, MJPG.This interface also used to upgrade
6M48.
27.AEC:The range of power:AC 85-264V 50/60Hz
28.Power switch;
VSP 1314
User’s Manual
47
5.System Setup and Operation
How to make equipment normal operation
How to make equipment normal operation
1. Make sure equipment normal operation;
2. After power on equipment starts self state,fan starts,scan button;
3. After scanning,LCD will show as following:
AVDSP Series VSP 1314
Seamless Switcher & Scaler
System Initializing 100%
CH1:DVI1 NO INPUT
CH2:DVI2 NO INPUT
3
Output:
1
A
F
V1
V2
1024X768 60Hz
4. Afer starting,equipment default load factory parameter or save 1 system
parameter,the function button light;
5. Equipment is started normal.
VSP 1314
User’s Manual
48
5.System Setup and Operation
How to preview input signal source
How to preview input signal source
Make sure equipment normal operation.Detail please refer to :How to make
equipment normal operation
Operation as following:
1. The signal of green light output from Program,can check output if
connect monitor or LED screen send card;
2. The signal of yellow light output from Preview,can check output if
connect monitor;
3. The signal of red light can preview switching,can check image at
preview output;
4. System default DVI as Program output,DVI2 and VGA as Preview
output;
5. Schematic diagram 1 switch to Schematic diagram 2,just to press
TAKE.
Schematic diagram 1:
Schematic diagram 2:
VSP 1314
User’s Manual
49
5.System Setup and Operation
How to adjust output resolution
How to adjust output resolution
Make sure equipment normal operation.Detail please refer to :How to make
equipment normal operation
Operation as following:
1. Press
light up green light to enter to MENU;
2. LCD shows the menu mode,rotate the adjust knob to select OUTPUT;
Input
Output
Split
View
3. Press knob to make sure,Enter to OUTPUT to select Output Format;
Output Format
Output Adjust
Screen
Aspect Ratio
4. Press knob to make sure,Enter to Output Format;Press knob to select
sresolution,then press to make sure;
Output Format
<1024x768 60Hz>
Press<OK>Select Format
VSP 1314
User’s Manual
50
5.System Setup and Operation
How to adjust size and position of image
How to adjust size and position of image
Make sure equipment normal operation.Detail please refer to : How to
make equipment normal operation
Operation as following:
Three button combination operation as following:
SCALE:
1. Press SCALE/CROP,light up green light-SCALE setting;
2. Press H SIZE\H POS,light up green-Height setting,rotate the adjust
knob can adjust the height of image;
DVI2
Scale HSize
Scale HPos
Scale VSize
Scale VPos
<1024>
< 0>
< 768>
< 0>
3. Press H SIZE\H POS,light up red light-transverse position setting,rotate
the adjust knob,can adjust the position of transverse;
VSP 1314
User’s Manual
51
5.System Setup and Operation
How to adjust size and position of image
DVI2
Scale HSize
Scale HPos
Scale VSize
Scale VPos
<1024>
< 0>
< 768>
< 0>
4. Press V SIZE/V POS ,light up green light-Width setting,rotate the adjust
knob can adjust the weith of image;
DVI2
Scale HSize
Scale HPos
Scale VSize
Scale VPos
<1024>
< 0>
< 768>
< 0>
5. Press V SIZE/V POS,light up red light-vertical position setting,rotate the
adjust knob can adjust the position of vertical;
DVI2
VSP 1314
Scale HSize
Scale HPos
Scale VSize
Scale VPos
<1024>
< 0>
< 768>
< 0>
User’s Manual
52
5.System Setup and Operation
How to scale image
How to scale image
Make sure equipment normal operation.Detail please refer to : How to
make equipment normal operation
Operation as following:
Three button combination operation as following:
CROP:
1. Press SCALE/CROP,light up red light-scale setting;
2. Press H SIZE\H POS,light up green light-Height setting,rotate the adjust
knob can adjust height of image;
DVI2
Crop HSize
Crop HPos
Crop VSize
Crop VPos
< 100>
< 50>
< 100>
< 50>
3. Press H SIZE\H POS ,light up red light-transverse position
setting,rotate the adjust knob can adjust position of TRANSVERSE;
DVI2
VSP 1314
Crop HSize
Crop HPos
Crop VSize
Crop VPos
< 100>
< 50>
< 100>
< 50>
User’s Manual
53
5.System Setup and Operation
How to scale image
4. Press V SIZE/V POS,light up green light-width setting,rotate the adjust
knob can just width of image;
DVI2
Crop HSize
Crop HPos
Crop VSize
Crop VPos
< 100>
< 50>
< 100>
< 50>
5. Press V SIZE/V POS ,light up red light-vertical position setting,rotate
the adjust knob can adjust the position of vertical;
DVI2
VSP 1314
Crop HSize
Crop HPos
Crop VSize
Crop VPos
< 100>
< 50>
< 100>
< 50>
User’s Manual
54
5.System Setup and Operation
How to switch signal of single image
How to switch signal of single image
Make sure equipment normal operation.Detail please refer to :How to make
equipment normal operation
Operation as following:
Layer 1 is the program output signal source from DVI,Now DVI light up
green light,and the other signal button are light out that at the same
layer,can’t to be selected;If need to switch program input signal,can select
signal button of other layer arbitrarily;When DVI2 light up yellow light,it
means DVI2 output to Preciew,other signal button light up red light,user
according to the need to select the button and light up yellow light ,Press
TAKE to switch the selected signal to Program output.
Operation as following:
Operation schematic diagram1:
Operation schematic diagram2:
VSP 1314 support display 3 layers :
Layer 1 including:CV1,CV2,USB1,DVI1,VGA1 ,
Layer 2 including:CV3,CV4,USB2,DVI2,VGA2 ,
Layer 3 is background input,user can set DVI3 as background signal or as
test pattern.
VSP 1314
User’s Manual
55
5.System Setup and Operation
How to set picture in picture
How to set picture in picture
Make sure equipment normal operation.Detail please refer to :How to make
equipment normal operation
PIP Functional description:
Before press,
make sure signal firstly;
Such as want set VGA1 as big picture,size is::960x672,and set DVI2 as
small picture,size is:384x384,position is:X-288,Y-144
Operation as following:
1. Set VGA1 as Preview output,scale to:960x672;
2. Press TAKE to switch VGA1 as Program output;
3. Set DVI2 as Preview output,scale to:384x384,and adjust position to:
X-288,Y-144;
4. Press PIP1/PIP2,and button light up red ;
5. PIP mode 1:Press button and light up green,as following:
6. PIP mode 2:Press button and light up red,as following:
VSP 1314
User’s Manual
56
5.System Setup and Operation
How to select switching effect
How to select switching effect
Make sure equipment normal operation.Detail please refer to :How to make
equipment normal operation
Operation description:
TAKE is the effect switch button. The switching effect must be setted in
menu.After setting,press TAKE to switch.
Operation as following:
1.Press
and button light up red;Rotate the
2.adjust knob to select switch effect.There are 4 kinds of switch effect: Cut、
Fade in Fade out、Wipe soft、Wipe hard;
Effects
*Effectsn Mode:<CUT>
Effects
*Effectsn Mode:<FADE>
Display Time:<1.5S>
Effects
*Effectsn Mode:<WIPE Hard>
Wipe Mode: < Wipe Left>
Wipe Speed: <8 S>
Effects
*Effectsn Mode:<WIPE SOFT>
Wipe Mode: < Wipe Left>
Wipe Speed: <8 S>
VSP 1314
User’s Manual
57
5.System Setup and Operation
How to select switching effect
3. Press the adjust knob to ensure after selecting,then to set switch speed
and mode,press the adjust knob to ensure;
VSP 1314
User’s Manual
58
5.System Setup and Operation
How to set input matrix
How to set input matrix
Make sure equipment normal operation.Detail please refer to :How to make
equipment normal operation
Operation description:
This function can support 2 or 3 layers to play the same videos,to meet
various requirements.
Operation as following:
1.Press
and light up green;
2.LCD shows the MENU,rotate the adjust knob to select Input;
Input
Output
Split
View
3.Press the adjust knob to ensure,and rotate the adjust knob to select
3.
Input Format
Input Matrix
4.and enter to set Input Matrix;
Channel 1:
Channel 2:
Channel 3:
Input 1
Input 2
Test Pattern
5.Press the adjust knob to ensure and enter Matrix;Rotate the adjust knob
to set these 3 Channel,That can achieve matrix;
VSP 1314
User’s Manual
59
5.System Setup and Operation
How to set DVI3 as background
How to set DVI3 as background
Make sure equipment normal operation.Detail please refer to :How to make
equipment normal operation
Operation description:
The system default background for test pattern,There are two ways to use
background:One is to use own test pattern,anther one is to use DVI3 inout
signal;It must make sure the input resolution of DVI3 is the same with
equipment before set DVI3 as background;
Operation step as following:
1.Press
and light up green;
2.LCD shows MENU mode,press the adjust knob to select Input
Input
Output
Split
View
3.Press the adjust knob to ensure to enter it;Rotate the adjust knob to
select Matrix;
Input Format
Input Matrix
4.Press to ensure and enter Matrix;Press the adjust knob to select Channel
3 and press to ensure.If DVI3 signal is effective and the output resolution
is the same with equipment,LCD will show input success if not will show
Error infomation!
Channel 1:
Channel 2:
Channel 3:
VSP 1314
Input 1
Input 2
Test Pattern
User’s Manual
60
5.System Setup and Operation
How to set DVI3 as background
5.Please make sure that input and output formats are consistent ,if show
Input Error;
DVI 3 Input Error!
Please Make Sure That Input And
Output Formats are Consistent!
VSP 1314
User’s Manual
61
5.System Setup and Operation
How to splicing with DVI3
How to splicing with DVI3
Make sure equipment normal operation.Detail please refer to :How to make
equipment normal operation
Splicing:
VSP1314 also is a seamless switcher,As a switcher use the DVI3 to input
signal,The max resolution of switcher is twice of DVI3 input,output interface
is DVI1 output and DVI2 output, and preview DVI3 signal via output
VGA;There are transverse and vertical splicing;Such as DVI3 input
is1920x1080,so can splicing 3840x1080 or 1920x2160.
Operation as following:
1.Press
and light up green;
2.LCD shows MENU mode,rotate the adjust knob to select Splicing;
Input
Output
Split
View
3.Press the adjust knob to ensure and enter it;
Split Switch:
Split Mode:
Split Output Channel:
Display Width:
OFF
Through
DVI1
1024
4.Press the adjust knob to select switch,ratote to open it;
Split Switch:
Split Mode:
Split Output Channel:
Display Width:
ON
Through
DVI1
1024
5. Press the adjust knob then rotate it to select Split Mode.Press the adjust
knob then rotate it to select Split Mode.There are three kinds of split
mode:Through、H1/2、V1/2;
VSP 1314
User’s Manual
62
5.System Setup and Operation
How to splicing with DVI3
Split Switch:
Split Mode:
Split Output Channel:
Display Width:
ON
H 1/2
DVI1
1024
6. Press the adjust knob and rotate it to select Split Output Channel,press
to enter it.There are DVI1 and DVI2.Output channel can be set
separately;
Split Switch:
Split Mode:
Split Output Channel:
Display Width:
ON
H 1/2
DVI1
1024
Split Switch:
Split Mode:
Split Output Channel:
Display Width:
ON
H 1/2
DVI1
1024
Display Height:
Display Local X:
Display Local Y:
Screen Width:
768
0
0
1024
7. Repeat the above operation step,can adjust the display range of DVI3
input source.That is scale a part image of DVI3 and display on output
port.
Display Height:
Display Local X:
Display Local Y:
Screen Width:
VSP 1314
768
0
0
1024
User’s Manual
63
5.System Setup and Operation
How to splicing with DVI3
8.Repeat above operation step to adjust the output image,That is adjust the
size and position of output image;
Screen Height:
Screen Local X:
Screen Local Y:
Config Update (Push OK)
768
0
0
9.Parameter correction,If splicing is stagger or there is a flower on
screen,because of DVI3 input interrupt or unstable,can correct the
parameter.
Screen Height:
Screen Local X:
Screen Local Y:
Config Update (Push OK)
VSP 1314
User’s Manual
768
0
0
64
5.System Setup and Operation
How to use BLACK
How to use BLACK
Make sure equipment normal operation.Detail please refer to :How to make
equipment normal operation
BLACK:
Black signal is a special effect which in order to set background directlly in
the special scene.
VSP1314 default layer 3 as background,That is button 0 is the background;
Operation step as following:
1.Press
and light up yellow ,at preview can
2.check the image;
3.If is not background,please press and light up green.LCD shows the
4.MENU mode,press the
adjust knob to select Test Pattern;
USB Setting
Test Pattern
Language
System
5.Press the adjust knob and enter it,select Manua Color;
Manual Color
Auto Color
Roll Right
Roll Left
6.Press the adjust knob and enter it;Press the adjust knob to set Red、
Green、Blue as 0,That is set test pattern as background;
Red:
Green:
Blue:
VSP 1314
0
0
0
User’s Manual
65
5.System Setup and Operation
How to use Test Pattern
How to use Test Pattern
Make sure equipment normal operation.Detail please refer to :How to make
equipment normal operation
Test Pattern:
If there is no signal source from outside,the equipment have own test
pattern,like as a video generator, can meet different scene;
Operation step as following:
1.If is not background please press
and light up green,rotate
the adjust knob to select Test Pattern;
USB Setting
Test Pattern
Language
System
2.Press the adjust knob to ensure and enter it to select the menu of Test
Pattern;
Manual Color
Auto Color
Roll Right
Roll Left
Roll Up
Roll Down
Roll Up Left
Roll Down Right
Color BAR H
Color BAR V
Gray BAR H
Gray BAR V
3.User can select mode arbitrarily then press to ensure;
VSP 1314
User’s Manual
66
5.System Setup and Operation
How to save parameter
How to save parameter
Make sure equipment normal operation.Detail please refer to :How to make
equipment normal operation
User save user can load diferent scene directly
There are 10 group of save;
Operation step as following:
1.Press
and light up green;
2.Button1,2,3,4,5,6,7,8,9,10 light up green at the same time;
3.Select the position of save,press the button and LCD shows SAVING;
Picture1:save mode
VSP 1314
User’s Manual
67
5.System Setup and Operation
How to load parameter
How to load parameter
Make sure equipment normal operation.Detail please refer to :How to make
equipment normal operation
User can load saving directly.There are 10 groups of load;
Operation step as following:
1.Press
and light up red;
2.Button1,2,3,4,5,6,7,8,9,10 light up red at the same time;
3.Select the position of load,press that button and button light off;
4.Can load circularly;
Picture 1:Load mode
Picture 2:Load 2 mode
Picture 3:Load 4 circularly mode
VSP 1314
User’s Manual
68
A.Specification
CVBS Input
Number of inputs
4
Connector
Standard BNC Socket
Supported
PAL/NTSC
Standard
Signal
1Vpp±3db
Supported
480i,576i
(0.7V Video+0.3v Sync ) 75 ohm
Resolution
VGA Input
Number of inputs
2
Connector
Standard DB9 Socket
Supported
VGA-UXGA
Standard
Signal Level
R、G、B、Hsync、Vsync:0 to1Vpp±3dB (0.7V Video+0.3v Sync ) 75 ohm
black level:300mV Sync-tip:0V
Supported
VGA-UXGA (800*600@60, 1024*768@60, 1280*1024@60,
Resolution
1440*900@60,1600*1200@60)
YPbPr Input
Number of inputs
2
Connector
Standard DB9 Socket
Supported
HD analog input
Standard
Signal Level
Y:1Vpp±3dB (0.7V Video+0.3v Sync ) 75 ohm Pb/Pr:0.7Vpp±3dB 75
ohm
Supported
480i,576i,480p,576p,720p50,720p60,1080i50,1080p50
Resolution
1080i60,1080p60
DVI Input
Number of inputs
2
Connector
Standard DVI-I Socket
Supported
SMPTE:625/25/50 PAL, 525/29.97/59.94 NTSC,
Resolution
1080P50,1080P59.94/60,1080i50,1080i59.94/60,
720p50,720p59.94/60
VESA:800×600×60Hz,1024×768×60Hz,1280×768×60Hz,
1280×1024×60Hz,1600×1200×60Hz,1920×1080×60Hz
Signal Level
TMDS pwl,single pixel input,165MHz bandwidth
Standard
HDMI 1.3
Signal Level
TMDS pwl, 165MHz bandwidth
Background Input
Number of inputs
1
VSP 1314
User’s Manual
69
Connector
Standard DVI-I Socket
Supported
VESA:800×600×60Hz,1024×768×60Hz,1280×768×60Hz,
Resolution
1280×1024×60Hz,1600×1200×60Hz,1920×1080×60Hz
Signal Level
TMDS pwl,single pixel input,165MHz bandwidth
Standard
DVI 1.0
Signal Level
TMDS pwl, 165MHz bandwidth
USB Output
Number of inputs
2
Connector
Standard USB Interface
Supported
Picture format:JPGE,BMP,PGN
Standard
Video format:MPEG2,MPEG3, MPEG4,H264, RM,RMVB,MOV,
MJPEG, VC1,DivX,FLV
VGA Output
Number of inputs
1
Connector
Standard DVI-I Socket
Supported
VESA: 1024×768×60Hz, 1280×768×60Hz,1280×720×60Hz,
Resolution
1280×1024×60Hz,1366×768×60Hz,1400×1050×60Hz,
1440×900×60Hz,1440×900×60_r Hz,1600×1200×60Hz,
1680×1050×60Hz,1920×1080×60Hz.
Signal Level
R、G、B、Hsync、Vsync:0 to1Vpp±3dB (0.7V Video+0.3v Sync ) 75 ohm
black level:300mV Sync-tip:0V
DVI Output
Number of inputs
2
Connector
Standard DVI-I Socket
Signal Level
TMDS pwl, 165MHz bandwidth
Supported
VESA: 1024×768×60Hz, 1280×768×60Hz,1280×720×60Hz,
Resolution
1280×1024×60Hz,1366×768×60Hz, 1400×1050×60Hz,
1440×900×60Hz,1440×900×60_r Hz,1600×1200×60Hz,
1680×1050×60Hz,1920×1080×60Hz.1920x1200_60 Hz.
Function illustration
Input
channel
Support programming configuration of every input channel signal
allocation button
Dural-screen
Support background image overlay
Switch
Support arbitrary channel switch with fade-in and fade-out
Accessories products and services
Setting control
RS232
USB TCP/IP
Power
85-264V 2.1A IEC-3 power port
Working
0°C~45°C
environment
Store environment
10% to 90%
Product
One year quality assurance with limited
quality
assurence
VSP 1314
User’s Manual
70
B.Contact Information
Warranty:
RGBlink Science & Technology Co., Ltd policy is 1 year warranty and
3-year labor warranty since delivery day for the main components (basic
motherboard, internal power supply, keyboard, LCD module, VGA input
module, CVBS input module, DVI input module, sending card, etc.). Within
the guaranteed maintenance period, customers can send back the
products if malfunction, and freight users from themselves.
Users have the obligation to record the failure reasons if products
malfunction. It does not belong to the warranty scope for any following
circumstances, but can charge maintenance:
1) No 3 packets of proves and valid invoice.
2) The warranty vouchers have altered, the serial number of warranty and
products of in-kind goods or altered identification inconsistent, or
replacement.
3) The damage caused by user's use, operation, maintenance, keep
improper.
4) The damage caused by non-our-company authorized service personnel
or assigned service provider overhaul, or open without authorization.
5) The damage caused by force majeure (such as lightning, voltage
instability).
6) Premium services that RGBlink set.
Headquarter: S603~604 Weiye Building Torch Hi-Tech Industrial
Development Zone Xiamen, Fujian Province, P.R.C
 Tel: +86-592-5771197
 Fax:+86-592-5771202
 Webpage:

VSP 1314
~ http://www.rgblink.com
~ http://www.rgblink.cn
E-mail:rgblinkcs@gmail.com
User’s Manual
71
C.Firmware Upgrade
Function Firmware Upgrade
1. Firstly, connect device and computer with reticle; input network address
of VSP 1314 firmware upgrade in the address bar: 192.168.0.100;
2. Input your user name admin in the popup dialog box, rgblink: 123
password.
3. Thirdly,click FPGA&FONT Upgrade to enter upgrade page;
VSP 1314
User’s Manual
72
4.press【browse„】choose upgrade document, the name of document
must be:xxx.bin or xxx.fon;
5. Click【Update】 to send,and wait for upgrading;User can check the
program loading process 、 rewrite time and whether is success on
equipment,or can check on the network page;
VSP 1314
User’s Manual
73
6. It will show :Upgrade Font Success after finish.And restart the equipment
to check whether operation is normal.
Image Firmware Upgrade
All the two USB interface must be upgraded.Because it can improve the
image quality,the upgrade etepsare as following:
1、Input USB enter to USB interface.
2、After start equipment enter to the menu,and find the menu of(Video
fireware Updata),can select USB1 and USB2.
3、Select the corresponding USB interface to upgrade,LCD display
―firmware upgrade please wait‖
4、“( Update Main Board
Update Success) ”it means updete
sucess,now you can upgrade other
USB interface to upgrade,the steps the same as above.
5、Restart equipment to check operation.
VSP 1314
User’s Manual
74
Communication Firemware Upgrade
Shut the power device, switch the direction of arrow of the two dial switch
which download IP board to ON state. As shown in figure:
Connect one end of RJ11 download line to RS232 .control Connector of
video processor end access and the other end access PC serial port.
Double-click
,enter into the procedure Connector of Flash
Magic,setting in figure: First, users select the corresponding serial ports,
set baud rate as 115200, choosing device LPC2368 and loading target file
of 100 M IP board of the upgrade program. (hex. File) Then, comfirm it
through choosing two
Finally, click ―start‖ button.
VSP 1314
User’s Manual
75
When download is finish, quit, shut the power equipment, reset two dial
code reset (as shown in figure), restart the power equipment, check
whether the equipment operate or not.
Note
Flash Magic software download website:
http://www.flashmagictool.com/download.html&d
=FlashMagic.exe
VSP 1314
User’s Manual
76
Download PDF