EM-GST80x v1.0
User's Manual
GST-802/802S
GST-805A
GST-806A15/806B15
GST-806A60/806B60
10/100/1000Base-T to 1000Base-LX/SX
Smart Media Converter
-1-
Trademarks
Copyright © PLANET Technology Corp. 2009.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective
owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications,
and makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment on the
part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s
Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and
reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s
Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your
comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET 10/100/1000Base-T to 1000Base-LX/SX Smart Media Converter User’s manual
MULTI-MODE: GST-802 / GST-805A
SINGLE-MODE: GST-802S / GST-805A / GST-806A15 / GST-806B15 / GST-806A60 / GST-806B60
REVISION: 1.0 (JUNE.2009)
Part No.: EM-GST80x_v1.0 (2080-AA1130-000)
-2-
TABLE OF CONTENTS
1. INTRODUCTION.......................................................................................................................................... 4
1.1 CHECKLIST ................................................................................................................................................ 4
1.2 ABOUT THE 10/100/1000BASE-T TO 1000BASE-LX/SX SMART MEDIA CONVERTER..................................... 4
1.3 FEATURES ................................................................................................................................................. 4
1.4 SPECIFICATION .......................................................................................................................................... 5
1.5 PRODUCT OUTLOOK ................................................................................................................................... 7
2. HARDWARE INSTALLATION .................................................................................................................... 9
2.1 STAND-ALONE MEDIA CONVERTER INSTALLATION ........................................................................................ 9
2.2 SLIDE MEDIA CONVERTER MODULE INTO MC-1600MR/R48 / MC-1610MR/MR48 CHASSIS INSTALLATION . 10
2.3 REAL ETHERNET ENVIRONMENT APPLICATION ............................................................................................ 11
3. MANAGE THE MEDIA CONVERTER....................................................................................................... 13
3.1 DIP SWITCH CONFIGURATION ................................................................................................................... 13
3.2 MANAGED MEDIA CONVERTER MODULE THROUGH MC-1600MR/R48 & MC-1610MR/R48 CHASSIS .......... 14
4. LINK PASS THROUGH FUNCTION ......................................................................................................... 17
4.1 LINK LOSS CARRY FORWARD (LLCF)........................................................................................................ 17
4.2 LINK LOSS RETURN (LLR) ........................................................................................................................ 18
5. TROUBLESHOOTING................................................................................................................................ 19
APPENDIX A NETWORKING CONNECTION............................................................................................... 20
A.1 SWITCH‘S RJ-45 PIN ASSIGNMENTS ......................................................................................................... 20
A.2 RJ-45 CABLE PIN ASSIGNMENT ................................................................................................................. 20
A.3 CABLE CONNECTION PARAMETER............................................................................................................. 21
-3-
1. INTRODUCTION
1.1 Checklist
Thank you for purchasing PLANET 10/100/1000Base-T to 1000Base-LX/SX Smart Media Converter, the
10/100/1000Base-T to 1000Base-LX/SX Smart Media Converter package shall contain following contents:
Check the contents of your package for following parts:
z
10/100/1000Base-T to 1000Base-LX/SX Smart Media Converter x1
z
User's manual CD x1
z
DC 5V 2A Power Adapter x1
If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton
including the original packing material, and use them against to repack the product in case there is a need to return it to
us for repair.
1.2 About the 10/100/1000Base-T to 1000Base-LX/SX Smart Media Converter
The Smart Gigabit Media Converter- GST-80x series extends communication distance with highly Gigabit performance via
fiber optical cable. The GST-80x series provides media conversion between 10/100/1000Base-T and 1000Base-SX/LX
interfaces such as multi-mode LC/SC connectors (220m / 550m), single-mode LC/SC connectors
(10/20/30/40/50/70/120km) and single fiber connectors (WDM,15/60km) for various fiber optic applications.
The GST-80x series provides Auto MDI/MDI-X on its TP port and the DIP switch to configure the available smart functions
including the auto-negotiation / force for fiber interface and Link Pass Through function (LLCF/LLR). The Link Loss Carry
Forward (LLCF) function works with Link Loss Return (LLR) to diagnose network connections. Also, the LLR function can
immediately alarm network administrator the media link issue and provide efficient solution to monitor the entire network.
The GST-80x series allows two type segments to connect easily. The Smart Media Converter can be used as a standalone
unit when powered by it’s DC adapter or used as a slide-in module to the PLANET 19-inch Web Smart / Managed 16-Slots
media converter chassis (MC-1600MR/MC-1600MR48 & MC-1610MR / MC-1610MR48). When working with the Web
Smart / Managed media converter chassis, the GST-80x is able to be managed and its status be monitored through the
local RS-232 console and remote web interface.
1.3 Features
¾
Standards:
… Complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T, IEEE 802.3z
1000Base-SX/LX Ethernet Standard
¾
Interface:
… One 10/100/1000Base-T port with RJ-45 connector
… One 1000Base-SX/LX port with LC/SC/WDM connector supporting multi-mode or single-mode fiber optic
cable
… Auto-negotiation and Auto-MDI / MDI-X for 10/100/1000Base-T port
¾
Layer 2 Features:
… Back-pressure & IEEE 802.3x compliant flow control and full wire-speed forwarding rate
… 9K Jumbo Frame size supported
… Link Loss Return (LLR) switch on each fiber optic to aid in troubleshooting remote network connections
… Link Loss Carry Forward (LLCF) work with LLR in diagnosing network connections
-4-
¾
Smart Management:
… Provides DIP switch for fiber (Auto-negotiation / Manual) and LFP function (Disable / Enable) setting
… Manageable through Web Smart / Managed Media Converter Chassis System
(MC-1600MR/MC-1610MR series)
… Bandwidth control / TS-1000 OAM / IEEE 802.3ah OAM / Loop Back Test function provided with
MC-1610MR / MC-1610MR48 Managed Media Converter Chassis System
¾
Hardware:
… Used as a stand-alone device or work with Web Smart / Managed Media Converter Chassis for up to 16
converter with redundant power supply for optional expansion use
… LED indicators for converter status
… Choice of fiber-connector from SC, LC, WDM, multi-mode / single-mode fiber / 1000Base-SX / LX mini
GBIC module
… EMI standards complies with FCC, CE class A
1.4 Specification
Model
GST-802
GST-802S
GST-805A
GST-806
A15
GST-806
B15
GST-806
A60
GST-806B
60
Hardware Specification
IEEE 802.3, 10Base-T
IEEE 802.3u, 100Base-TX
Standards
IEEE 802.3ab, 1000Base-T
IEEE 802.3z, 1000Base-SX/LX
IEEE 802.3ah OAM
Ports
1 x 10/100/1000Base-T port,
Copper Interface
1 x 1000Base-SX/LX port
RJ-45 port (Auto-MDI/MDI-X) Twisted Pair
Optic Interface
SC
Optic Wavelength
Launch
Power(dBm)
850nm
SFP
1310nm
-
WDM
TX:1310
nm
TX:1550
nm
TX:1310
nm
TX:1550
nm
RX:1550
nm
RX:1310
nm
RX:1550
nm
RX:1310
nm
Max.
-4 dBm
-3 dBm
-
-3 dBm
+5 dBm
-3 dBm
+4 dBm
Min.
-9.5 dBm
-9.5dBm
-
-9 dBm
0 dBm
-9 dBm
-1 dBm
-13.5
dBm
-14.4 dBm
-
-21 dBm
-25 dBm
-21 dBm
-25 dBm
-18 dBm
-20 dBm
-
-3 dBm
-3 dBm
-2 dBm
-2 dBm
Receive Sensitivity
Maximum Input power
10/20Mbps for Half / Full-Duplex
Speed
Twisted-pair
100/200Mbps for Half / Full-Duplex
2000Mbps for Full-Duplex
Fiber-optic
2000Mbps for Full-Duplex
-5-
10Base-T: 2-pair UTP Cat. 3,4,5, up to 100 m
Twisted-pair
Cable
100Base-TX: 2-pair UTP Cat. 5, up to 100 m
1000Base-T: 4-pair STP Cat 5 up to 100m
DIP Switch
y 50/125μm or 62.5/125μm multi-mode fiber cable, up to 220/550m.
y 9/125μm single-mode cable, provides long distance for 10/20/30/40/50/70/120km
(vary on fiber transceiver or SFP module)
y PWR (Green)
y TP: 1000, LINK/ACT
y Fiber: LINK/ACT
Fiber (Auto-negotiation / Manual), LFP (Disable / Enable)
Power Consumption
3.1 Watts / 10BTU (maximum)
OAM
TS-1000, IEEE 802.3ah terminal
Jumbo Frame size
9K
Power Input
DC 5V / 2A
Dimension (W x D x H)
81 x 94 x 26 mm
Weight
214g
Operating Environment
Temperature: 0~50 Degree C; Humidity: 5~90% non-condensing
Storage Environment
Temperature: -40~70 Degree C; Humidity: 5~90% non-condensing
Emissions
FCC Class A, CE Class A
Fiber-optic
Cable
LED Indicator
-6-
1.5 Product Outlook
Right View: there is one RJ-45 twisted-Pair jack (Auto-MDI/MDI-X), one fiber-optic connector (vary by model) and six
LED indicators.
Left View: there is one DC jack for DC 5V power adapter.
GST-802 / GST-802S:
GST-805A:
-7-
GST-806A15 / GST-806B15 / GST-806A60 / GST-806B60:
LED Indicators
LED
Color
Status
Indication
PWR
Green
Fiber LNK /ACT
Green
TP LINK/ACT
Green
TP 1000
Green
Lights Off
Lights On
Lights Off
Lights On
Lights Blink
Lights Off
Lights On
Lights Blink
Lights Off
Lights On
Power off.
Power on – when +5V DC detected.
Indicate the link through that port is not established.
Indicate the link through that port is successfully established.
Indicate that port is actively sending or receiving data.
The link through that port is not established.
The link through that port is successfully established.
Indicate that port is actively sending or receiving data.
Indicate that the port is operating at 10Mbps or 100Mbps.
Indicate that the port is operating at 1000Mbps.
-8-
2. HARDWARE INSTALLATION
This product provides two different running speeds – 10/100/1000Base-T and 1000Base-LX/SX in the same device.
This section describes the hardware installation of GST-80x. Before connecting any network device to the GST-80x, read
this chapter carefully.
2.1 Stand-alone Media Converter Installation
The GST-80x can use as a stand-alone Media Converter for Plug & Play and quick network environment deploy, please
follow these steps to install the converter:
•
Turn off the power of the device/station in a network to which the GST-80x will be attached.
•
Ensure that there is no activity in the network.
•
Attach fiber cable from the GST-80x to the fiber network. TX, RX must be paired at both ends.
•
Attach a Cat. 5/5e/6 UTP cable from the 10/100/1000Base-T network to the RJ-45 port on the GST-80x.
•
Connect the 5VDC power adapter to the GST-80x and verify that the Power LED lights up.
•
Turn on the power of the device/station, the TX Link /Act and LX/SX Link/Act LEDs should light when all cables are
attached.
•
1 0 / 1 0 0 / 1 0 0 0 Ba s e -T
Cat.5 / 5 e/ 6
C a b le Ne t w o rk
GST-80X
1 0 / 1 0 0 / 1 0 0 0 Ba s e -T t o
1 0 0 0 Ba s e -L X/ S X
1 0 0 0 Ba s e -S X/ L X
RX
TX
TX
F ib e r Ne t w o rk
RX
#Notice:
„
1. RJ-45/STP, UTP Cat 5/5e/6, straight/crossover cable is accepted.
„
2. Please refer to Appendix A for more about the wiring distance of your TP and fiber- Optic cable.
-9-
2.2 Slide Media Converter module into MC-1600MR/R48 / MC-1610MR/MR48 Chassis
installation
Step 1- Unscrew and pull out the GST-80x Media Converter board.
Step 2- Remove a blank faceplate from an empty expansion slot on the front of the chassis. The GST-80x Media Converter board can be installed in any expansion slot.
Step 3- Slide the GST-80x Media Converter board into the expansion slot, aligning it with the guide rails, until it firmly
connects to the chassis’ backplane.
- 10 -
Step 4- Secure the GST-80x Media Converter board to the chassis by tightening the thumbscrew.
2.3 Real Ethernet environment application
Fiber-Optic Networking for ISP, Enterprise, and Home
The GST-80x provides advanced Media conversion technology- 10/100/1000Base-T and 1000Base-SX/LX interfaces to
fulfill different kinds of demand as the current network grows and expanding. The GST-80x provides diverse fiber connect
type options for different network applications. It is very flexible for the GST-80x working as a standalone device or being
installed in the central Web Smart / Management Media converter chassis for centralized management. When working
with the Web Smart / Management Media converter chassis, the GST-80x is hot swappable to avoid network downtime.
The GST-80x is the ideal solution for building a network solution of FTTH (Fiber to the Home) or FTTC (Fiber to the Curb),
and FTTB (Fiber to the Building) for ISPs, campuses and enterprise.
Figure 1 : GST-80x FTTB application
- 11 -
Figure 2: GST-80x FTTX application
- 12 -
3. MANAGE THE MEDIA CONVERTER
This product provides two different managed methods – configure through its DIP Switch or install into the central Web
Smart / Management Media converter chassis for centralize management.
This section describes how to managed the GST-80x through its DIP Switch and Web Smart / Management Media converter chassis. Before use the GST-80x smart function, please read this chapter carefully.
3.1 DIP Switch configuration
The GST-80x provide DIP switch to setting fiber (Auto-negotiation / Manual) and LFP (Disable / Enable). Please refer to the
table below for more detail decription.
ON
1 2
DIP Switch
Mode
Description
DIP Switch 1
On
Fiber interface operates at Forced Mode.
Off
Fiber interface operates at Auto-Negotiation (Default).
On
LFP Enable.
Off
LFP Disable (Default).
DIP Switch 2
#Notice:
Be sure the opposite end is using the same setting (forced or Auto-negotiation). And when using two converters at the
same time, the two converters MUST set to forced mode.
- 13 -
3.2 Managed Media Converter module through MC-1600MR/R48 & MC-1610MR/R48
Chassis
The Web Smart / Management Media Coverter Chassis that can control GST-80x through the management system,
GST-80x can be controlled through Web Browser and terminal emulation program.
The Web Smart Media Coverter Chassis-MC-1600MR/R48 will display out the status of GST-80x, also the Web Smart
Media Coverter Chassis can control the function through the management system.
Through the Web Smart Media Coverter Chassis System, you can control the setting of GST-80X, such as device (Disable
/ Enable), LFP (Disable / Enable).UTP (Auto-negotiation / Manual), speed (10/100/1000Mbps) , duplex mode (Half / Full
duplex mode), Flow control (Disable / Enable). Fiber (Auto-negotiation / Manual).
Item
Description
Device
To enable or disable per GST-80x Converter board.
LFP
To enable or disable the LFP function from GST-80x Converter board.
TP AN Mode
To set the UTP port runs at Auto-negotiation or Forced Mode.
TP Speed
To set the UTP port runs at 1000Mbps, 100Mbps or 10Mbps.
TP Duplex
To set the UTP port runs at Full duplex or Half duplex mode.
TP FC
To set the Flow Control of the UTP port to enable or disable.
Fiber AN Mode
To set the Fiber port runs at Auto-negotiation or Forced Mode.
#Notice:
1.
Please to note that if converter is connect with switch whichis Auto negotiation, must enable the Auto neogtiaiton
function. If both devices are conveters must disable the Auto neogtiaiton function.
2.
Due to firmware structure and restriction of MC-1600MR/R48, the OAM / bandwidth control function not provide in
GST-80x setting Web page screen.
- 14 -
The Management Coverter Chassis-MC-1610MR/R48 will display out the status of GST-80x, also the Management Media
Coverter Chassis can control the function and OAM / Bandwidth control setting through the management system.
Through the Management Media Coverter Chassis System, you can control the setting of GST-80X, such as device
(Disable / Enable), LFP (Disable / Enable).UTP (Auto-negotiation / Manual), speed (10/100/1000Mbps) , duplex mode
(Half / Full duplex mode), Flow control (Disable / Enable). Fiber (Auto-negotiation / Manual).
Item
Description
Device
To enable or disable per GST-80x Converter board.
LFP
To enable or disable the LFP function from GST-80x Converter board.
TP AN Mode
To set the UTP port runs at Auto-negotiation or Forced Mode.
TP Speed
To set the UTP port runs at 1000Mbps, 100Mbps or 10Mbps.
TP Duplex
To set the UTP port runs at Full duplex or Half duplex mode.
TP FC
To set the Flow Control of the UTP port to enable or disable.
Fiber AN Mode
To set the Fiber port runs at Auto-negotiation or Forced Mode.
#Notice:
Please to note that if converter is connect with switch whichis Auto negotiation, must enable the Auto neogtiaiton function.
If both devices are conveters must disable the Auto neogtiaiton function.
- 15 -
For easily to know the TP / Fiber port link status of oppsite device, the Management Media Coverter Chassis System
provide OAM Setting that include TS-1000 OAM / IEEE 802.3ah OAM / Loop Back Test function. Also the
bandwidth control function allow to define available transmit / receive bandwidth on TP / Fiber port of GST-80x.
Item
Description
OAM Setting
Provide OAM Configuration on GST-80x.
Ingress Rate Limit
Define receive rate for bandwidth control from TP and Fiber ports of GST-80x.
Egress Shaping
Define transmit rate for bandwidth control from TP and Fiber ports of GST-80x.
#Notice:
Please refer to manual of Management Media Coverter Chassis (MC-1610MR/R48) for more detail about OAMSetting and
bandwidth control function.
- 16 -
4. LINK PASS THROUGH FUNCTION
The LFP function includes the Link Fault Pass Through function (LLCF/LLR) and the DIP Switch design. LLCF/LLR can
immediately alarm administrators the problem of the link media and provide efficient solution to monitor the net. The DIP
Switch provides disable or enable the LFP function.
LLCF (Link Loss Carry Forward) means when a device connected to the converter and the TP line loss the link, the
converter’s fiber will disconnect the link of transmit. LLR (Link Loss Return) means when a device connected to the converter and the fiber line loss the link, the converter’s fiber will disconnect the link of transmit. Both can immediately alarm
administrators the problem of the link media and provide efficient solution to monitor the net.
4.1 Link Loss Carry Forward (LLCF)
The GST-80X modules incorporates default LLCF function for troubleshooting a remote connection; the Fiber/TP ports do
not transmit a link signal until they receive a link signal from the opposite port.
The diagram below shows a typical network configuration with a good link status using GST-80X for remote connectivity.
Management Switch/Hub
Station
w/SNMP
Media
Media
Converter
Converter
LLCF is ON
LLCF is ON
TP
Switch/Hub Management
Fiber
w/SNMP
Station
TP
Cable
● LED lit = established link
○ LED unlit = no link
If the connection breaks, GST-80X that link loss forward to the switch/hub which generates a trap to the management
station. The administrator can then determine the source of the issue.
Management Switch/Hub
Station
w/SNMP
Media
Media
Converter
Switch/Hub Management
Converter
w/SNMP
Station
LLCF is ON
LLCF is ON
TP
Broken
TP
Fiber
● LED lit = established link
○ LED unlit = no link
#Notice:
The converter is shipped with the default LFP (LLCF/LLR) function disable.. This feature can also be turned on on-purpose.
If you are familiar with the network installation and for diagnostic purpose (i.e. check which end is broken), you can turn it on
and the converter will take effect immediately. Otherwise, please remains it in the default position.
- 17 -
4.2 Link Loss Return (LLR)
The fiber ports of GST-80X have been designed with an LLR function for troubleshooting a remote connection. LLR works
in conjunction with LLCF.
When LLR is enabled*, the port’s transmitter shuts down when its receiver fails to detect a valid receive link. LLR should
only be enabled on one end of the link and is typically enabled on either the unmanaged or remote device.
The diagram below shows a typical network configuration with a good link status using GST-80X for remote connectivity.
Note that LLR is enabled as indicated in the diagram.
Management Switch/Hub
Station
w/SNMP
Media
Media
Converter
Converter
Switch/Hub Management
w/SNMP
Station
LLCF is ON
LLCF is ON
Fiber
Cable
● LED lit = established link
○ LED unlit = no link
If one of the optical conductors is bad (as shown in the diagram box below), the converter with LLR enabled will return a
no-link condition to its link partner. With LLCF also default enabled, the no-link condition is carried forward to the switch/hub
where a trap is generated to the management station, and the administrator can then determine the source of the loss.
Management Switch/Hub Media
Media
Station
Converter
w/SNMP
Converter
Switch/Hub Management
w/SNMP
Station
LLCF is ON
LLCF is ON
Broken
Port 2
Link Loss Carried Forward
● LED lit = established link
Fiber
Port 1
Link Loss Carried Forward
Link Loss Returned
○ LED unlit = no link
#Notice:
The converter is shipped with the default LFP (LLCF/LLR) function disable.. This feature can also be turned on on-purpose.
If you are familiar with the network installation and for diagnostic purpose (i.e. check which end is broken), you can turn it on
and the converter will take effect immediately.. Otherwise, please remains it in the default position.
- 18 -
5. TROUBLESHOOTING
This chapter contains information to help you solve issues. If the GST-80x is not functioning properly, make sure the
GST-80x was set up according to instructions in this manual.
The Power LED is not lit
Solution:
Check the power cable connection between power adapter and GST-80X.
Why I connect GST-80x to device with 1000Base-LX/SX interface and the 1000Base-LX/SX fiber connection fail?
Solution:
1. Please check the fiber connection between two devices is correct.
2.
Please check the 1000Base-LX / SX interface from both devices run at force full duplex mode.
3.
Check and if the 1000Base-LX/SX interface of other device run at Auto-negotiation mode only,
please enable the Auto negotiation bypass function of GST-80x for successful fiber connection.
10/100/1000Base-T port link LED is lit, but the traffic is irregular
Solution:
1. Check that the attached device is not set to dedicate full duplex. Some devices use a physical or software switch
to change duplex modes. Auto-negotiation may not recognize this type of full-duplex setting.
2.
Check and assure the TP ports from both GST-80x and attached device run at Auto-negotiation mode.
- 19 -
APPENDIX A NETWORKING CONNECTION
A.1 Switch‘s RJ-45 Pin Assignments
1000Mbps, 1000Base T
Contact
MDI
MDI-X
1
BI_DA+
BI_DB+
2
BI_DA-
BI_DB-
3
BI_DB+
BI_DA+
4
BI_DC+
BI_DD+
5
BI_DC-
BI_DD-
6
BI_DB-
BI_DA-
7
BI_DD+
BI_DC+
8
BI_DD-
BI_DC-
A.2 RJ-45 cable pin assignment
The standard RJ-45 receptacle/connector
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation
and color of straight cable and crossover cable connection:
Figure A-1: Straight-Through and Crossover Cable
Please make sure your connected cables are with same pin assignment and color as above picture before deploying the
cables into your network.
- 20 -
A.3 Cable Connection Parameter
The limitations are shown as below;
Standard
Fiber Type
Cable Specification
1000Base-SX
Multi-mode
50/125μm or 62.5/125μm
1000Base-LX
Multi-mode
50/125μm or 62.5/125μm
(1300nm)
Single-mode
9/125μm
(850nm)
Wiring Distances:
Standard
1000Base-SX
1000Base-LX
Fiber
MM
MM
SM
Diameter
Modal Bandwidth
Max. Distance
(micron)
(MHz * km)
(meters)
62.5
100
220
62.5
200
275
50
400
500
50
500
550
62.5
5
550
50
4
50
5
9
N/A
5000*
#Notice:
1: Consult your local dealer for more about PLANET single mode fiber connectivity.
2. The Single-mode port (1000Base-LX port) of GST-802S, GST-805A, GST-806A15/B15 and GST-806A60/B60 is
complied with LX 5 kilometers and provides additional margin allowing for a 10 / 15 / 60 kilometers Gigabit Ethernet link
on single mode fiber.
3. A model (GST-806Ann, TX: 1310nm; RX: 1550nm) and B model (GST-806Bnn, TX: 1550nm; RX: 1310nm) should runs
in pair and same distance model, i.e. nn=15 or 60.
2080-AA1130-000
- 21 -
EC Declaration of Conformity
For the following equipment:
*Type of Product : 10/100/1000Base-T to 1000Base-SX/LX Smart Gigabit Media Converter
*Model Number : GST-802 / GST-802S
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address:
11F, No 96, Min Chuan Road,
Hsin Tien, Taipei, Taiwan, R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (89/336/EEC,92/31/EEC,93/68/EEC).
For the evaluation regarding the EMC, the following standards were applied:
Emission
Harmonic
Flicker
Immunity
ESD
RS
EFT/ Burst
Surge
CS
Magnetic Field
Voltage Disp
EN 55022
EN 61000-3-2
EN 61000-3-3
EN 55024
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
EN 61000-4-11
(1998 Class A)
(2000)
(1995)
(1998)
(1995)
(1995)
(1995)
(1995)
(1996)
(1993)
(1994)
Responsible for marking this declaration if the:
⌧ Manufacturer
Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name:
Planet Technology Corp.
Company Address:
11F, No.96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C
Person responsible for making this declaration
Name, Surname
Kent Kang
Position / Title :
Product Manager
Taiwan
Place
26th, Jun., 2009
Date
Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected]
http://www.planet.com.tw
11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
EC Declaration of Conformity
For the following equipment:
*Type of Product
: 10/100/1000Base-T to 1000Base-SX/LX Smart Gigabit Media Converter
(mini-GBIC,SFP)
: GST-805A
*Model Number
* Produced by:
Manufacturer‘s Name :
Manufacturer‘s Address:
Planet Technology Corp.
11F, No 96, Min Chuan Road
Hsin Tien, Taipei, Taiwan, R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (89/336/EEC,92/31/EEC,93/68/EEC).
For the evaluation regarding the EMC, the following standards were applied:
Emission
Harmonic
Flicker
Immunity
ESD
RS
EFT/ Burst
Surge
CS
Magnetic Field
Voltage Disp
EN 55022
EN 61000-3-2
EN 61000-3-3
EN 55024
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
EN 61000-4-11
(1998 Class A)
(2000)
(1995)
(1998)
(1995)
(1995)
(1995)
(1995)
(1996)
(1993)
(1994)
Responsible for marking this declaration if the:
⌧ Manufacturer
Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name:
Planet Technology Corp.
Company Address:
11F, No.96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C
Person responsible for making this declaration
Name, Surname
Kent Kang
Position / Title :
Product Manager
Taiwan
Place
26th, Jun., 2009
Date
Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected]
http://www.planet.com.tw
11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
EC Declaration of Conformity
For the following equipment:
*Type of Product
: 10/100/1000Base-T to 1000Base-LX WDM Smart Gigabit Media Converter
(Tx: 1310/1550) - 15KM/60KM
: GST-806A15 / GST-806B15 / GST-806A60 / GST-806B60
*Model Number
* Produced by:
Manufacturer‘s Name :
Manufacturer‘s Address:
Planet Technology Corp.
11F, No 96, Min Chuan Road
Hsin Tien, Taipei, Taiwan, R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (89/336/EEC,92/31/EEC,93/68/EEC).
For the evaluation regarding the EMC, the following standards were applied:
Emission
Harmonic
Flicker
Immunity
ESD
RS
EFT/ Burst
Surge
CS
Magnetic Field
Voltage Disp
EN 55022
EN 61000-3-2
EN 61000-3-3
EN 55024
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
EN 61000-4-11
(1998 Class A)
(2000)
(1995)
(1998)
(1995)
(1995)
(1995)
(1995)
(1996)
(1993)
(1994)
Responsible for marking this declaration if the:
⌧ Manufacturer
Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name:
Planet Technology Corp.
Company Address:
11F, No.96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C
Person responsible for making this declaration
Name, Surname
Kent Kang
Position / Title :
Product Manager
Taiwan
Place
26th, Jun., 2009
Date
Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected]
http://www.planet.com.tw
11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement