Emerson | CF720ORB00 | Owner`s manual | Emerson CF720ORB00 Owner`s manual

BP7309 BANFF
1/3/08
7:24 AM
Page 1
READ AND SAVE THESE INSTRUCTIONS
Model No.
BANFF™
52” Ceiling Fan
Owner's Manual
CF720ORB00
CF720PW00
CF720WB00
Net Weight:
22.2
Lbs.
INSTRUCTION TO THE USER
(if device contains a digital device)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a Class B computing device,
pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded
cables must be used with this equipment. Operation with non-approved equipment or
unshielded cables is likely to result in interference to radio and TV reception. The user is
cautioned that changes and modifications made to the equipment without the approval of
manufacturer could void the user’s authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
Part No. F40BP73090001
Form No. BP7309-1
UL Model No. CF720
BP7309 BANFF
1/3/08
7:24 AM
Page 2
!
WARNING
WARNING: To avoid fire, shock, and serious personal injury, follow these
instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock
service panel disconnecting means to prevent power from being switched on
accidentally. When the service disconnecting means cannot be locked,
securely fasten a warning device, such as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the
fan. Always turn off the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before
wiring, and do not operate fan without blades.
2. The installation is to be in accordance with the National Electrical Code,
ANSI/NFPA 70-1999 and Local Codes. Use the National Electrical Code if Local
Codes do not exist. The ceiling fan must be grounded as a precaution against
possible electrical shock. Electrical installation should be made or approved
by a licensed electrician.
3. The outlet box and joist must be securely mounted and capable of reliably
supporting at least 50 pounds. Use only U.L. outlet boxes listed as
“Acceptable for Fan Support”, and use the mounting screws provided with the
outlet box. Most outlet boxes commonly used for support of light fixtures are
not acceptable for fan support and may need to be replaced. Consult a
qualified electrician if in doubt.
4. The fan must be mounted with the fan blades at least 7 feet from the floor to
prevent accidental contact with the fan blades.
5. Follow the recommended instructions for the proper method of wiring your
ceiling fan. If you do not know enough about electrical wiring, have your fan
installed by a licensed electrician.
NOTE: This fan is suitable for use with solid-state speed controls.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used
with fan speed control Model No. UC7067RC, manufactured by Rhine Electric Co., Ltd.
WARNING: This product is designed to use only those parts supplied with this
product and/or any accessories designated specifically for use with this product
by Emerson Electric Co. Substitution of parts or accessories not designated for
use with this product by Emerson Electric Co. could result in personal injury or
property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange
when installing the blade flanges, balancing the blades or cleaning the fan. Do not
insert foreign objects in between rotating fan blades.
WARNING: To reduce the risk of electric shock, this fan must be installed with
an isolating wall control/switch.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label.
You should record this data above and keep it in a safe place for future use.
2
BP7309 BANFF
1/3/08
7:24 AM
Page 3
This Manual is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
Installed Wire Length
Up to 50 ft.
50-100 ft.
One Phillips head screwdriver
One wire stripper
One stepladder
Five wire connectors (supplied)
Four 15-watt (maximum) candelabra
bulbs (not supplied)
Two 60-watt (maximum) candelabra
bulbs (not supplied)
!
Wire Size A.W.G.
14
12
WARNING
Before assembling your ceiling fan, refer
to section on proper method of wiring
your fan (page 10). If you feel you do not
have enough wiring knowledge or
experience, have your fan installed by a
licensed electrician.
Materials
Wiring, outlet box and box connectors
must be of type required by the local code.
The minimum wire would be a 3-conductor
(2-wire with ground) of the following sizes:
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each
step is completed, place a check mark in the box. This will insure that all steps
have been completed and will be helpful in finding your place should you be
interrupted.
!
NOTE: If you are uncertain of part
description, refer to exploded view
illustration.
WARNING
Do not install or use fan if any part is
damaged or missing. Call Toll-Free:
a. Fan motor and housing uplight
assembly
b. One ceiling canopy
c. Five blade flanges
d. Five fan blades
e. One hanger bracket
f. One hanger ball/downrod assembly
g. One lower glass bowl
h. One downlight fitter assembly
i. One upper glass
j. One SW101 Fan/Light Wall Control
1-800-654-3545
!
WARNING
This product is designed to use only
those parts supplied with this product
and/or any accessories designated
specifically for use with this product by
Emerson Electric Co. Substitution of
parts or accessories not designated for
use with this product by Emerson Electric
Co. could result in personal injury or
property damage.
1. Open styrofoam unit containing fan.
Remove top half of styrofoam unit.
Remove parts and check to see that
you have received the following parts:
3
BP7309 BANFF
1/3/08
7:24 AM
Page 4
Electrical Requirements
k. One loose parts bag containing:
1. Two 1-1/4” threaded studs
2. Two knurled knobs
3. Two lockwashers
4. Three wire connectors
5. One clevis pin
6. One hairpin clip
7. Eleven M5 x 16mm oval
head screws
8. Sixteen M5 x 6mm slotted
Phillips washer head screws
A
IMPORTANT: Your ceiling fan will not
function properly, and may be
damaged, if used with any wall dimmer
switch or control other than the
Emerson Electric SW101 Fan/Light Wall
Control supplied with the fan, or an
optional Emerson Electric SR100
Remote Control.
Your new ceiling fan will require a
grounded electrical supply line of 120 volts
AC, 60 Hz, 15 amp circuit.
C
B
The outlet box must be securely anchored
and capable of withstanding a load of at
least 50 pounds.
!
To reduce the risk of fire, electric shock,
or personal injury, mount fan to outlet box
marked “Acceptable for Fan Support”,
and use screws supplied with outlet box.
Most outlet boxes commonly used for
support of light fixtures are not
acceptable for fan support and may need
to be replaced. Consult a qualified
electrician if in doubt.
D
E
WARNING
G
F
I
H
If your fan is to replace an existing ceiling
light fixture, turn electricity off at the main
fuse or circuit breaker box at this time and
remove the existing light fixture.
J
K
!
HI
LIGHT
WARNING
MED
LOW
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
All wiring must be in accordance with
National and Local codes and the ceiling
fan must be properly grounded as a
precaution against possible electrical
shock.
FAN OFF
EMERSON®
OFF
ON
NOTE: Place the parts from the loose
parts bags in a small container to keep
them from being lost.
2. Remove the fan motor and housing
uplight assembly from the protective
plastic bag. Place the fan motor and
housing uplight assembly on a padded
work surface with the bottom of the
motor facing up.
IMPORTANT: Remove the two cardboard retainers from between the
housing uplight and the motor
housing.
4
BP7309 BANFF
1/3/08
7:24 AM
Page 5
Ceiling Fan Procedures
M5 x 6mm SLOTTED PHILLIPS
WASHER HEAD SCREWS (3)
General
Your Emerson ceiling fan comes supplied
with a SW101 Fan/Light Wall Control and
a Remote Control Receiver. This system
allows you to regulate your ceiling fan
speed and light intensity.
FAN
BLADE
BLADE FLANGE
NOTE: An optional Emerson Electric
SR100 Remote Control may also be
used to control your ceiling fan.
How to Assemble Your
Ceiling Fan
!
Figure 1
2. Rotate the motor and housing uplight
assembly so that one of the flange slots
in the motor and housing uplight
assembly lines up below the access
cutout in the motor and housing uplight
assembly (Figure 2). Insert the blade
flange through the slot and line up the
holes in the flange with the threaded
holes in the motor and housing uplight
assembly .
WARNING
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
All wiring must be in accordance with
National and Local codes and the ceiling
fan must be properly grounded as a
precaution against possible electrical
shock.
IMPORTANT: Before assembling your
ceiling fan, refer to the Owner’s Manual
supplied with the SW101 Fan/Light Wall
Control and set the operating
frequency of the fan/light wall control
and the Remote Control Receiver.
Also, install the fan/light wall control in
the wall box as described in the wall
control Owner’s Manual. You are now
ready to proceed with the assembly
and installation of your ceiling fan.
MOTOR AND
HOUSING
UPLIGHT
ASSEMBLY
ACCESS
CUTOUT
BLADE
FLANGE
1. Mount the fan blades to the blade
flanges using three M5 x 6mm slotted
Phillips washer head screws (Figure 1).
!
FLANGE
SLOT
M5 x 16mm OVAL HEAD SCREWS (2)
WARNING
Figure 2
To reduce the risk of personal injury, do
not bend the blade flange when installing
the blade flanges, balancing the blades or
cleaning the fan. Do not insert foreign
objects in between rotating fan blades.
!
WARNING
To reduce the risk of personal injury, do
not bend the blade flange when installing
the blade flanges, balancing the blades or
cleaning the fan. Do not insert foreign
objects in between rotating fan blades.
5
BP7309 BANFF
1/3/08
7:24 AM
Page 6
3. Carefully position a M5 x 16mm oval
head screw in one flange hole and
loosely tighten the screw (Figure 2).
Install the second screw in the same
manner and securely tighten both
screws. Repeat steps 2 and 3 for the
remaining four blade assemblies.
!
WARNING
It is critical that the clevis pin in the motor
coupling is properly installed and the
setscrews securely tightened. Failure to
verify that the pin and setscrews are
properly installed (as shown in Figure 4)
could result in the fan falling.
NOTE: Take care not to scratch the fan
housing when installing the blade
assemblies.
DOWNROD
HAIRPIN
CLIP
CLEVIS
PIN
4. Remove the hanger ball by loosening
the setscrew in the hanger ball until the
ball falls freely down the downrod
(Figure 3). Remove the pin from the
downrod, then remove the hanger ball.
Retain the pin and hanger ball for
reinstallation in step 10.
MOTOR
COUPLING
MOTOR AND
HOUSING
UPLIGHT
ASSEMBLY
PIN
SETSCREW (2)
HANGER
BALL
DOWNROD
REMOVE THREE M4 x 12mm
PAN HEAD SCREWS AND
RUBBER WASHERS
SETSCREW
Figure 4
6. Tighten the two setscrews (Figure 4)
securely while pulling up on the
downrod.
Figure 3
5. Unscrew the two setscrews (Figure 4)
until they clear the inside of the motor
coupling. Then separate, untwist and
unkink the three 80” motor leads. Route
the motor lead wires through the
downrod. Align the clevis pin holes in
the downrod with the holes in the motor
coupling. Install the clevis pin and
secure with the hairpin clip (Figure 4).
The clevis pin must go through the
holes in the motor coupling and the
holes in the downrod. Be sure to push
the straight leg of the hairpin clip
through the hole near the end of the
clevis pin until the curved portion of the
hairpin clip snaps around the clevis pin.
The hairpin clip must be properly
installed to prevent the clevis pin from
working loose. Pull up on the downrod
to make sure the clevis pin is properly
installed.
7. Remove and retain three M4 x 12mm
pan head screws and rubber washers
from the motor and housing uplight
assembly (Figure 4).
8. Place the upper glass on the motor and
housing uplight assembly. Line up the
three holes in the upper glass with the
three threaded holes in the motor and
housing uplight assembly (Figure 5).
Install an M4 x 12mm pan head screw
and rubber washer in each of the holes
(Screws and rubber washers were
removed in step 7).
6
BP7309 BANFF
1/3/08
7:24 AM
Page 7
11. The fan comes with blue, black and
white leads that are 80” long. Before
installing the fan, measure up
approximately 6 to 9-inches above
top of hanger ball/downrod assembly.
Cut off excess leads and strip back
insulation 1/2” from end of leads.
INSTALL THREE M4 x 12mm
PAN HEAD SCREWS AND
RUBBER WASHERS
15-WATT
(MAX.)
CANDELABRA
BULBS (4)
12. You have now completed the initial
assembly of your new ceiling fan. You
can now proceed with hanging and
wiring your fan.
UPPER
GLASS
MOTOR
AND
HOUSING
UPLIGHT
ASSEMBLY
How to Hang
Your Ceiling Fan
Figure 5
9.
Screw in four 15-watt (maximum)
candelabra bulbs (not supplied) in the
motor and housing uplight assembly
sockets (Figure 5).
!
WARNING
The fan must be hung with at least 7'
of clearance from floor to blades
(Figure 7).
10. Place the ceiling canopy over the
downrod. Then reinstall the hanger
ball (Figure 6) on the downrod as
follows. Route the three 80” motor
leads through the hanger ball and
slide the hanger ball over the
downrod. Position the pin through the
two holes in the downrod and align
the hanger ball so the pin is captured
in the groove in the top of the hanger
ball. Pull the hanger ball up tight
against the pin and securely tighten
the setscrew in the hanger ball. A
loose setscrew could create fan
wobble.
CEILING
AT
LEAST
7'
FLOOR
Figure 7
!
PIN
HANGER
BALL
CEILING
CANOPY
Figure 6
WARNING
The outlet box and joist must be
securely mounted and capable of
supporting at least 50 lbs. Use only a
U.L. outlet box listed as “Acceptable
for Fan Support”.
SETSCREW
DOWNROD
7
BP7309 BANFF
1/3/08
!
7:24 AM
Page 8
NOTE: CEILING COVER, SUPPLY WIRES AND FAN
WIRES OMITTED FOR CLARITY.
WARNING
To reduce the risk of fire, electric
shock, or personal injury, mount fan
to outlet box marked “Acceptable for
Fan Support”, and use screws
supplied with outlet box. Most outlet
boxes commonly used for support of
light fixtures are not acceptable for
fan support and may need to be
replaced. Consult a qualified
electrician if in doubt.
OUTLET
BOX
HANGER
BRACKET
HANGER BALL/
DOWNROD ASSEMBLY
Figure 9
1. Securely attach the hanger bracket to
the outlet box using the two screws
supplied with the outlet box (Figure 8).
!
!
WARNING
To avoid possible fire or shock, do
not pinch wires between the hanger
ball/downrod assembly and hanger
bracket.
WARNING
Hanger bracket must seat firmly
against outlet box. If the outlet box is
recessed, remove wall board until
bracket contacts box. If bracket
and/or outlet box are not securely
attached, the fan could wobble or
fall.
How to Wire
Your Ceiling Fan
If you feel that you do not have enough
electrical wiring knowledge or experience, have your fan installed by a
licensed electrician.
OUTLET
BOX
TWO SCREWS
SUPPLIED
WITH
OUTLET BOX
!
HANGER
BRACKET
Turning off wall switch is not
sufficient.
To
avoid
possible
electrical shock, be sure electricity is
turned off at the main fuse box
before wiring. All wiring must be in
accordance with National and Local
codes and the ceiling fan must be
properly grounded as a precaution
against possible electrical shock.
TAB
Figure 8
2. Carefully lift the fan and seat the hanger
ball/downrod assembly on the hanger
bracket that was just attached to the
outlet box (Figure 9). Be sure the groove
in the ball is lined up with the tab on the
hanger bracket (Figure 8).
!
WARNING
CAUTION: To reduce the risk of electrical shock, disconnect the electrical
supply circuit before installing the fan,
light kit or receiver.
WARNING
Failure to seat tab in groove could
cause damage to electrical wires and
possible shock or fire hazard.
8
BP7309 BANFF
1/3/08
7:24 AM
Page 9
c. Securely connect the supply black wire
(hot) wire to the receiver black (AC IN
L) wire.
d. Securely connect the fan motor white
wire to the receiver white (TO MOTOR
N) wire.
e. Securely connect the fan motor black
wire to the receiver red (TO MOTOR L)
wire.
f. Securely connect the fan motor blue
wire to the receiver blue (FOR
LIGHT) wire.
1. Position the supply wires to the left side
of the outlet box (Figure 10); position
the fan wires to the right side. Partially
insert the remote control receiver (flat
side up) until one end rests on the
hanger ball as shown in Figure 10.
NOTE: Make all wiring connections
using wire connectors (supplied). Make
sure that all connections are tight,
including ground, and that no bare wire
is visible at the wire connectors, except
for the ground wire.
2. Refer to Figures 10 and 11 and connect
the receiver wires to the supply wires
and the fan motor wires as follows:
a. Securely connect the green grounding
wires from the hanger ball and the
hanger bracket to the supply grounding
conductor (this may be a bare wire or a
wire with green insulation).
b. Securely connect the supply white
(neutral) wire to the receiver white
(AC IN N) wire.
Check to see that all connections are
tight, including ground, and that no
bare wire is visible at the wire
connectors, except for the ground
wire. Do not operate fan until blades
are in place. Noise and fan damage
could result.
SUPPLY WHITE WIRE
(NEUTRAL)
AC IN
SUPPLY BLACK
WIRE (HOT)
GROUND WIRE
WARNING
!
RECEIVER WHITE
WIRE
RECEIVER
BLACK WIRE
N
RECEIVER RED WIRE
1-1/4" THREADED
STUD (2)
RL
OTO
TO
M
FAN
BLACK
WIRE
ANTENNA
GREEN GROUND
WIRE FROM
HANGER BRACKET
GHT
TO MO
AC IN L
FOR LI
GREEN GROUND
WIRE FROM
HANGER BALL
TOR N
RECEIVER BLUE
WIRE
FAN BLUE WIRE
FAN WHITE WIRE
Figure 10
9
RECEIVER WHITE WIRE
BP7309 BANFF
1/3/08
7:24 AM
Page 10
SW101 FAN/LIGHT WALL
CONTROL (SUPPLIED)
TO
120VOLT
SUPPLY
BLACK
BLACK
(HOT)
BLACK
HI
LIGHT
MED
LOW
FAN OFF
WHITE
EMERSON®
OFF
ON
WHITE
WHITE
GROUND
RED
TWO-CONDUCTOR
CABLE (WITH
GROUND)
BLUE
WHITE
BLACK
BLUE
WHITE
GREEN WIRE (GROUND)
FROM HANGER BALL AND
HANGER BRACKET
HANGER BALL
Figure 11
3. Push the wires and connectors up into
the outlet box while inserting the
receiver fully into the hanger bracket.
Position the antenna wire on top of the
receiver.
4. Screw the two 1-1/4” threaded studs
(supplied) into the tapped holes in the
hanger bracket (Figure 10).
5. Lift the ceiling canopy up to the
threaded studs and turn until the studs
protrude through the holes in the ceiling
canopy (Figure 12).
!
WARNING
To avoid possible fire or shock, make
sure that the electrical wires are
completely inside the outlet box and
not pinched between the ceiling
canopy and the ceiling.
7. Engage the connectors of the downlight fitter assembly with the connectors
of the motor assembly (black to blue:
white to white) (Figure 13).
8. Remove and retain one of the three
M4 x 8mm oval head screws and
lockwashers from the fitter adapter
plate. Loosen the remaining two
screws and lockwashers.
6. Secure the ceiling canopy in place by
sliding lockwashers (supplied) over the
threaded studs and installing the two
knurled knobs (supplied) (Figure 12).
Tighten the knurled knobs securely
until the ceiling canopy fits snugly
against the ceiling.
REMOVE ONE M4 x 8mm
OVAL HEAD SCREW AND
LOCKWASHER.
LOOSEN THE TWO
REMAINING SCREWS AND
LOCKWASHERS.
CEILING
CANOPY
WHITE WIRES
FITTER
ADAPTER
PLATE
BLUE WIRE
Figure 12
1-1/4"
THREADED
STUD (2)
LOCKWASHER
(2)
KNURLED
KNOB (2)
BLACK WIRE
DOWNLIGHT
FITTER ASSEMBLY
Figure 13
10
KEYHOLE SLOTS
BP7309 BANFF
1/3/08
7:24 AM
Page 11
Operating Your
Ceiling Fan
9. Position the downlight fitter assembly
on the light fitter adapter plate so that
the two screws and lockwashers mate
with the keyhole slots in the downlight
fitter assembly. Make sure that all wires
and wire connectors are positioned
within the downlight fitter assembly.
Rotate the downlight fitter assembly
clockwise and tighten the two screws.
Install the other M4 x 8mm oval head
screw and lockwasher in the remaining
hole in the downlight fitter assembly.
!
IMPORTANT
Fan installation must be completed,
including the installation of the fan
blades, before testing of the remote
control.
Your Fan/Light Wall Control (Figure 15)
has full control of your fan and lights.
However, airflow direction is controlled by
a slide switch on the switch housing.
1. Restore electrical power to the outlet
box by turning the electricity on at the
service panel.
WARNING
Make sure there are no wires pinched
between the light fitter and the fitter
adapter plate.
DOWNLIGHT
FITTER
ASSEMBLY
NOTE: Make sure that the ON/OFF slide
switch on the Fan/Light Wall Control is
in the ON position.
2. To set the desired fan speed, press the
HI, MED, or LOW buttons to operate
your fan on high, medium, or low speed
(Figure 15).
INSTALL THREE
M4 x 8mm OVAL
HEAD SCREWS
AND
LOCKWASHERS
3. To turn your fan off, press the OFF
button.
TAB
4. To set the level of light brightness,
press and hold the LIGHT button. The
light brightness will continue to
increase then decrease while the
button is held down. When the lights
are at the desired brightness, release
the button.
60-WATT (MAX.)
CANDELABRA
BULB (2)
FLAT
AREA
LOWER
GLASS
BOWL
Figure 14
5. To turn the lights on and off, press and
release the LIGHT button. The lights
will turn on at the light level previously
set (see step 4).
10. Screw in two 60-watt (maximum)
candelabra bulbs (not supplied) in the
light fitter sockets (Figure 14).
6. If airflow is desired in the opposite
direction, turn the fan off and wait for
the blades to stop turning. Then slide
the reversing switch (on the motor and
housing uplight assembly) to the
opposite position (Figure 16) and turn
the fan on again. The blades will turn in
the opposite direction and reverse the
airflow.
11. Place the lower glass bowl into the
downlight fitter, aligning the three flat
areas on the glass bowl flange with
the three tabs on the downlight fitter
(Figure 14). Then turn the lower glass
bowl clockwise until the glass bowl
stops turning.
12. Your ceiling fan is now installed and
wired to be controlled by your SW101
Fan/Light Wall Control.
11
BP7309 BANFF
1/3/08
7:24 AM
Page 12
Maintenance
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
Periodic cleaning of your new ceiling fan is
the only maintenance that is needed.
HI
When cleaning, use only a soft brush or
lint free cloth to avoid scratching the finish.
LIGHT
MED
Abrasive cleaning agents are not required
and should be avoided to prevent damage
to finish.
LOW
FAN OFF
!
EMERSON®
OFF
WARNING
Do not use water when cleaning your
ceiling fan. It could damage the
motor or the blades and create the
possibility of an electrical shock.
ON
Accessories
Figure 15
1. Downrod Extension Kits (see store or
catalog).
2. Ceiling Fan Controls (see store or
catalog).
!
WARNING
The use of any other control not
specifically approved for this fan
could result in fire, shock and
personal injury.
REVERSING
SWITCH
!
WARNING
This product is designed to use only
those parts supplied with this
product and/or any accessories
designated specifically for use with
this product by Emerson Electric Co.
Substitution of parts or accessories
not designated for use with this
product by Emerson Electric Co.
could result in personal injury or
property damage.
Figure 16
12
BP7309 BANFF
1/3/08
7:24 AM
Page 13
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX
!
OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN.
Trouble Shooting
TROUBLE
1. Fan will not
start.
PROBABLE CAUSE
1. Fuse or circuit breaker
blown.
2. Loose power line
connections to the fan.
3. Fan/Light Wall Control is OFF.
4. Code switches in remote
control receiver and Fan/Light
Wall Control are not set in the
same position.
2. Fan sounds
noisy.
1. Blades not attached to fan.
2. Screws securing fan blade
flanges to motor are loose.
3. Screws holding blades to
flanges are loose.
SUGGESTED REMEDY
1. Check main and branch
circuit fuses or circuit breakers.
! WARNING: Make sure
main power is turned off.
2. Check line power connections
to fan.
3. Turn ON Fan/Light Wall Control.
4. Check that both code switches
are set in the same positions.
1. Attach blades to fan before
operating.
2. Check to make sure the screws
which attach the blade flanges
to the motor are tight.
3. Tighten screws securely.
WARNING: Make sure main
power is turned off.
4. Loose screws in motor housing. 4. Check to make sure all screws
in motor housing are snug
(not over-tight)
!
3. Fan wobbles
excessively.
1. Setscrews in motor coupling are 1. Tighten setscrews securely.
not tightened securely.
2. Setscrew in the hanger ball/
2. Tighten the setscrew in the
downrod assembly is loose.
hanger ball/downrod assembly.
3. Screws securing fan blade
3. Check to be sure screws which
flanges to motor are loose.
attach the fan blade flanges
to the motor are tight.
4. Fan blade flanges not seated
4. Check to be sure that the
properly.
screws securing the fan
blade flanges seat firmly.
5. Hanger bracket and/or ceiling
5. Tighten the hanger bracket
outlet box is not securely
screws to the outlet box, and/or
fastened.
secure outlet box.
6. Fan blades out of balance.
6. Interchanging an adjacent (side
by-side) blade pair can
redistribute the weight and result
in smoother operation.
Or use supplied balancing kit to
balance blades.
13
BP7309 BANFF
1/3/08
7:24 AM
Page 14
Repair Parts
1
2
3
5
4
12
76
13
8
10
18
11
20
9
14
17
19
16
15
HI
LIGHT
MED
LOW
FAN OFF
EMERSON®
OFF
16
ON
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
• PART NUMBER
• NAME OF ITEM
• PART DESCRIPTION
• MODEL NUMBER
The model number of your Fan will be found on a label attached to the top housing.
For repair parts, phone 1-800-654-3545.
14
BP7309 BANFF
1/3/08
7:24 AM
Page 15
Repair Parts Listing
Part Numbers
Key
No.
Description
Model No.
CF720ORB00
Model No.
CF720PW00
Model No.
CF720WB00
*
1
2
3
Hanger Pack, Consisting of:
Hanger Bracket
Hanger Ball
Downrod
761655-50
—
—
—
761655-59
—
—
—
761655-48
—
—
—
*
4
5
6
7
8
9
10
Parts Bag, Containing:
Wire Connector (3)
Threaded Stud, 1-1/4” (2)
Knurled Knob, 8-32 (2)
Lockwasher, #8 (2)
Hairpin Clip
Clevis Pin
Screw, Slotted Phillips Washer
Head, M5 x 6mm (16)
Screw, Oval Head,
M5 x 16mm (11)
763083
—
—
—
—
—
—
763083
—
—
—
—
—
—
763083
—
—
—
—
—
—
—
—
—
—
—
—
763070-ORB
763070-PW
763070-WB
763071
763071-1
763071
763080-ORB
763080-PW
763080-WB
763073
763073-1
763073
—
—
—
763084
763084
763084
11
12
Ceiling Canopy
13
Upper Glass
14
Flange Assembly (set of 5)
15
Lower Glass
16
Wall Control SW101
17
Harness
18
Housing Uplight Assembly
763072-ORB
763072-PW
763072-WB
19
Housing Downlight Assembly
763074-ORB
763074-PW
763074-WB
20
Blade Assembly (set of 5)
763082-1
763082-2
763082
—
Owner's Manual
BP7309-1
BP7309-1
BP7309-1
15
BP7309 BANFF
1/3/08
7:24 AM
Page 16
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against
all defects in workmanship and materials. You must be the original purchaser or user of the product to be
covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for a lifetime of your ceiling fan. All other components and
accessories are covered by this warranty for one year from the date you purchased your ceiling fan. ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH
RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other
accessory at no charge to you. If repair of the motor or blades is not practical or possible within a reasonable
time and no replacement can be provided, Emerson will refund the actual purchase price of your fan. WE WILL
SHIP THE REPAIRED PRODUCT OR REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE
FOR ALL COSTS OR REMOVAL, REINSTALLATION AND SHIPPING OF THE PRODUCT TO EMERSON ELECTRIC
CO.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY
SERVICE. KEEP YOUR RECEIPT OR OTHER PROOF OF PURCHASE. You can return the product to our factory
or to your nearest authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to
Air Comfort Products, Division of Emerson Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136.
Include all model numbers shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest
authorized service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized
service center. Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit
since we will not be responsible for any such damage.
What Is Not Covered:
The glass globes and light bulbs of your ceiling fan are not covered by this warranty. This warranty also does
not cover any defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal
wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are
voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other
written or oral warranties apply, and no employee, agent, dealer or other person is authorized to give any
warranties on behalf of Emerson Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS
WARRANTY AND EMERSON IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL
AND CONSEQUENTIAL DAMAGES. Incidental damages include but are not limited to such damages as loss of
time and loss of use. Consequential damages include but are not limited to the cost of repairing or replacing
other property which was damaged if this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above
exclusion or limitation may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
Form No. BP7309-1
Part No. F40BP73090001
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant ¥ St. Louis, MO 63136
Printed in China 08/06
Download PDF