Jordan Valve Mark 64 spec

Jordan Valve Mark 64 spec
Pressure Regulators
Mark 63/64 Series
Differential Pressure Regulators
The Jordan Mark 63 is designed to maintain a constant differential between the pressure on the discharge side of the regulator and the signal pressure
loaded on the diaphragm. The Mark 64 provides the
same flow capacity as the Mark 63 but with less offset
in controlled pressure due to a larger diaphragm.
The regulator is normally open. The outlet pressure
acts beneath the diaphragm and is opposed by the
force of the adjusting spring plus the pressure of the
loading medium. As the outlet pressure overcomes
the combined pressures on top of the diaphragm, the
regulator moves to the closed position.
Features
•
•
•
Mark 63/64 — maintains a constant differential
between the pressure on the discharge side of
the regulator and the signal pressure loaded on
the diaphragm. The MK64 features a larger effective diaphragm area for greater sensitivity.
Mark 63CDF — features a flow-through spring
housing for use in controlling atomizing steam or
air to oil burners.
Sliding Gate Seats — all of Jordan Valve’s differential regulators feature advanced sliding
gate seat technology: straight-through flow for
reduced turbulence and quiet operation; short
stroke for fast response and accurate regulation;
easily interchangeable Cv's; tight shutoff
Specifications
Sizes: (Note: 1/4" (DN8) & 3/8"(DN12) use 1/2"
(DN15) body with reducer bushings)
•
Mark 63: 1/4" (DN8) through 2" (DN50)
•
Mark 64: 1/4" (DN8) through 3/4" (DN20)
•
Mark 63CDF: 2-1/2" (DN65 through 4" (DN100)
End Connections:
•
Threaded — FNPT, BSPT, BSPP
•
ANSI Flanges — 150#, 300#
•
DIN Flanges — PN10/16, PN25/40
Body Materials:
•
Ductile Iron
•
Bronze
•
Carbon Steel — A216 WCB
•
Stainless Steel — SA351 CF8M
Trim Materials:
•
303 SST — Standard on Ductile Iron, Bronze, or
Carbon Steel valves
•
316SST — Standard on Stainless Steel valves
Seat Materials:
•
Jorcote on SST — Standard
•
Jorcote/Jordanic on SST — For severe service
•
Chrome Plated SST — Optional
Jordan Valve, a division of Richards Industries
3170 Wasson Road • Cincinnati, OH 45209
513.533.5600 • 800.543.7311 • 513.871.0105 (f)
[email protected] • www.jordanvalve.com
Mark 63/64 Differential Pressure Regulators
The Mark 63CDF features a flow-through spring housing that is designed to permit "in-oil-line" installation.
This is especially desirable where air or steam is used
for fuel oil atomization. The fuel oil flow through the
spring housing reduces the possibility of the oil asphalting on top of the diaphragm which would cause
a loss of differential pressure control and operating
sensitivity. For added protection in this service, the
Mark 63CDF includes a separated double diaphragm
that prevents the fluid from mixing in the event that
the diaphragm were to rupture.
Mark 63/64 Differential Pressure Regulators
Specifications (Cont'd)
Options (continued):
•
*D: Separated double diaphragm (prevents mixing
fluids in case of ruptured diaphragm)
•
DF: Double diaphragm/flow thru
•
HP: High pressure spring housing
•
H: Handwheel and packing box
•
HF: Handwheel/flow thru dome
•
HDF: Handwheel, double diaphragm/flow thru
dome
Diaphragm Materials
•
Stainless Steel — Standard
•
Buna-N
•
Viton
•
Jorlon
Spring Housing Materials: Ductile Iron (standard)
Contact Factory for other materials
Service: Steam, oil, gas, air, chemicals, and water
Shutoff: ANSI Class IV
* Available for Mark 63 and 64. Other options only available for
Mark 63.
Body Rating:
Body
Matl.
End
Conn.
T.E.
DI
150#FE
300#FE
600#FE
T.E.
BRZ
150#FE
300#FE
T.E.
CS
150#FE
300#FE
600FE
T.E.
SS
150#FE
300#FE
600#FE
-20 to
100˚F
300
(600)
250
600
600
300
(500)
225
500
300
(950)
285
740
950
300
(950)
275
720
950
200˚F
300˚F
400˚F
500˚F
600˚F
650˚F
300
(600)
235
600
600
300
(475)
215
475
300
(950)
260
675
950
300
(950)
240
620
950
300
(600)
215
600
600
300
(425)
195
425
300
(950)
230
665
950
300
(950)
215
560
950
300
(600)
200
525
600
300
(375)
170
375
300
(950)
200
635
950
300
(950)
195
515
950
300
(600)
170
495
600
300
(325)
150
325
300
(950)
170
600
950
300
(950)
170
480
950
300
(600)
140
465
600
300
(600)
125
450
600
N/A
N/A
N/A
N/A
300
(950)
140
550
950
300
(905)
140
450
905
N/A
N/A
300
(950)
125
535
950
300
(890)
125
445
890
Differential Pressure Control Ranges, PSI (BAR)
Model
Size
Ranges in psi (bar)
1/4" - 3/4"
(DN8 - 20)
MK63
1" - 2"
(DN25 DN50)
MK63HP
MK64
Note: Double bolting option is required to reach pressures indicated in
parenthesis ( ). For temperatures below -20°F or above 650°F, consult
factory
Note: To convert temperature to Celsius: subtract Fahrenheit temperature by 32, multiply result by 5, divide answer by 9, final answer to temperature in Celsius ((F-32)*5/9 = C). To convert PSI to BAR, divide by
14.5.
Maximum Dome Loading Pressure: the combined pressure of the spring setting (psig) and dome loading (psig)
must not exceed the body rating.
Options:
•
*C: Closing cap for adjusting screw
•
B: Bleed valve on spring housing (available only
with option C closing cap above)
•
*CD: Closing cap/separated double diaphragm
•
CDF: Closing cap/separated double diaphragm
and flow thru dome
•
CF: Closing cap/flow thru dome
•
*H: Handwheel and packing box
•
F: Flow-through spring housing. Permits “in-oil-line”
installation for fuel oil atomization and steam atomizing systems. Reduces the possibility of the oil
asphalting on top of the diaphragm
1/2" - 2"
(DN15-25)
1/4" - 3/4"
(DN8-20)
2-23
(0,14-1,6)
10-38
(0,7-2,6)
20-55
(1,4-3,8)
35-160
(2,4-11)
95-220
(6,6-15)
1-5
(0,07-0,34)
3-8
(0,21-0,55)
10-30
(0,7-2,1)
20-45
(1,4-3,1)
30-95
(2,1-6,6)
75-190
(5,2-13)
100-320
(6,9-22)
150-450
(10-31)
1-5
(0,07-0,34)
2-12
(0,14-0,8)
2-25
(0,14-1,7)
10-35
(0,7-2,4)
20-55
(1,4-3,8)
20-80
(1,4-5.5)
40-115
(2,8-8)
25-160
(1,7-11)
30-180
(2,1-12)
5-20
(0,34-1,4)
60-160
(4,1-11)
Cv (Kv) Value & Maximum Differential Pressures
Cv (Kv)
0.84 (0,74)
1.6 (1,4)
2.5 (2,2)
4.4 (3,8)
6.4 (5,5)
9.5 (8,2)
15 (12,9)
25 (21,5)
30 (25,8)
Size (DN)
1/4" (DN8)
3/8" (DN12)
1/2" & 3/4"
(DN15 & DN20)
1" & 1-1/4"
(DN25 & DN32)
1-1/2" ( DN40)
Seat Material
Jorcote
Jorcote
Max. ∆P PSI (bar)
400 (27,6)
400 (27,6)
Jorcote
400 (27,6)
Jorcote
400 (27,6)
Jorcote
325 (22,4)
2" (DN50)
Jorcote
325 (22,4)
* Low Flow Trim: reduced Cv’s (Kv’s) can be placed in
any size valve as long as it is smaller than the standard
Cv (Kv) for that particular size. In addition, the following
special low flows can be provided:
-2-
1.6 (1,4)
0.84
(0,72)
0.42
(0,36)
0.21
(0,18)
0.02
(0.017)
0.008
(0,007)
0.004
(0,003)
0.002
(0,0017)
0.08
(0,07)
0.04 (0,03)
0.0008 (not in 316SS)
(0,0007)
Mark 63/64 Differential Pressure Regulators
Mark 63 Series Dimensions
Flanged Ends
•
Dimensions (inches)
Size
1/2"
3/4"
D
1"
1-1/4"
1-1/2"
2"
B
A
ANSI
Flange
B
CS/
SS
DI/
BRZ
CS/
SS
All
All
DI/
BRZ
CS/
SS
DI/
BRZ
CS/
SS
150#
7.25
7.25
8.50
8.50
1.69
5.12
3.94
3.94
13
15
300#
7.50
7.50
8.50
8.50
1.69
5.12
3.94
3.94
14
16
150#
7.25
7.25
8.50
8.50
1.69
5.12
3.94
3.94
14
16
300#
7.52
7.62
8.50
8.50
1.69
5.12
3.94
3.94
16
17
150#
7.25
7.25
10.00
10.75
2.62
7.09
4.53
4.83
26
34
300#
8.75
7.75
10.00
10.75
2.62
7.09
4.53
4.83
28
37
—
150#
7.87
—
10.00
—
2.62
7.09
4.53
—
28
300#
8.37
—
10.00
—
2.62
7.09
4.53
—
31
—
150#
8.75
8.75
10.25
11.22
2.31
7.09
4.50
5.08
42
46
300#
10.25
9.25
10.25
11.22
2.31
7.09
4.50
5.08
45
52
150#
10.00
10.00
10.25
11.42
2.75
7.09
4.75
5.05
46
50
300#
10.50
10.50
10.25
11.42
2.75
7.09
4.75
5.05
49
55
Dimensions (mm)
Size
(DN)
C
20
25
32
40
50
DI/BRZ
All
All
DI/
BRZ
CS/
SS
DI/
BRZ
CS/
SS
10/16
1844
130
216
240
43
130
100
1001
5,9
6,8
25/40
1844
130
216
240
43
130
100
1001
6,4
7,3
10/16
184
4
150
216
240
43
130
100
100
1
6,4
7,3
25/40
1844
150
216
240
43
130
100
1001
7,3
7,7
10/16
1844
160
273
262
67
180
115
1232
11,8
15,4
25/40
1844
160
273
262
67
180
115
1232
12,7
16,8
10/16
2004
—
273
—
67
180
115
—
12,7
—
25/40
200
—
273
—
67
180
115
—
14,1
—
10/16
2224
200
279
285
59
180
114
1291
19,1
20,9
25/40
2224
200
279
285
59
180
114
1291
20,9
23,6
10/16
254
4
230
279
290
70
180
120
128
3
20,9
22,7
25/40
2544
230
279
290
70
180
120
1283
22,2
24,9
1"
1-1/4"
1-1/2
2"
D
E
Weight
(lbs.)
Size
(DN)
3.62
8.50
1.69
5.12
3.94
10
15 &
20
3.62
8.50
1.69
5.12
3.94
12
10.00
2.62
7.09
4.53
21
CS/SS
4.18
10.75
2.62
7.09
4.83
25
DI/BRZ
4.12
10.00
2.62
7.09
4.53
21
DI/BRZ
4.50
10.25
2.31
7.09
4.50
23
CS/SS
4.81
11.00
2.25
7.09
5.08
31
DI/BRZ
4.50
10.25
2.75
7.09
4.72
26
CS/SS
5.50
11.00
2.75
7.09
5.05
35
25
32
40
50
-3-
4
Threaded Ends, DIN
C
4.12
Weight (kg)
E
CS/
SS
B
CS/SS
D
DI/
BRZ
A
DI/BRZ
C
CS/
SS
•
Dimensions (inches)
B
DI/
BRZ
Threaded Ends
1/2" &
3/4"
A
Flange
(PN)
15
A
A1
Mat'l
Weight
(lbs.)
E
DI/
BRZ
E
Size
D
Flanged Ends, DIN
•
•
C
Mat'l
DI/BRZ
Dimensions (mm)
A
B
C
D
E
Weight
(kg)
92
216
43
130
100
4,4
CS/SS
92
216
43
130
100
5,4
DI/BRZ
105
254
67
180
115
9,5
CS/SS
106
273
67
180
123
11,3
DI/BRZ
105
254
67
180
115
9,5
DI/BRZ
114
260
59
180
114
10,4
CS/SS
122
279
57
180
129
14,0
DI/BRZ
114
260
70
180
120
11,8
CS/SS
140
279
70
180
128
15,9
Mark 63/64 Differential Pressure Regulators
Mark 64 Series Dimensions
D
B
E
C
A
A1
•
Flanged Ends
Dimensions (inches)
150#
1/2"
3/4"
•
A
ANSI
Flange
Size
B
C
D
Weight (lbs.)
E
DI/
BRZ
CS/
SS
DI/
BRZ
CS/
SS
All
All
DI/
BRZ
CS/
SS
DI/
BRZ
CS/
SS
9.62
9.62
10.25
10.25
2.25
7.12
4.33
4.25
26
26
300#
9.62
9.62
10.25
10.25
2.25
7.12
4.33
4.25
26
26
150#
10.25
10.25
10.25
10.25
2.25
7.12
4.33
4.25
29
29
300#
10.25
10.25
10.25
10.25
2.25
7.12
4.33
4.25
29
29
Flanged Ends, DIN
Dimensions (mm)
Size
(DN)
Flange
(PN)
10/16
15
20
•
3/4"
B
C
D
Weight (kg)
E
DI/
BRZ
CS/
SS
DI/
BRZ
CS/
SS
All
All
DI/
BRZ
CS/
SS
DI/
BRZ
CS/SS
244
244
260
260
57
181
110
108
12
12
25/40
244
244
260
260
57
181
110
108
12
12
10/16
260
260
260
260
57
181
110
108
6,4
13
25/40
260
260
260
260
57
181
110
108
7,3
13
Threaded Ends
Size
1/2"
A
Dimensions (inches)
A
B
C
D
E
Weight
(lbs.)
DI/BRZ
3.62
10.25
2.25
7.12
4.33
12
CS/SS
3.62
10.25
2.25
7.12
4.25
13
DI/BRZ
3.62
10.25
2.25
7.12
4.33
12
CS/SS
3.62
10.25
2.25
7.12
4.25
13
Mat'l
Threaded Ends, DIN
•
Size
(DN)
15
20
-4-
Dimensions (mm)
A
B
C
D
E
Weight
(kg)
DI/BRZ
92
260
57,2
181
110
5,5
CS/SS
92
260
57,2
181
110
5,5
DI/BRZ
92
260
57,2
181
108
5,9
CS/SS
92
260
57,2
181
108
5,9
Mat'l
Mark 63/64 Differential Pressure Regulators
Ordering Schematic
Model
Options
Size
Body
Material
/
1
2
3
Model
4
5
6
7 8
9
10 11 12 13
3&4
14 15
Trim
63
Standard
S3
64
Large Diaphragm
S6
316SS
I3
303SS F/IFE (1/2" - 2")
I6
316SS F/IFE (1/2" -2")
Options
303SS
*C
Closing Cap
*CD
Closing Cap/Separated DBL Diaphragm
CDF
Closing Cap/Separated DBL Diaphragm + Flow
Thru Dome
CF
Closing Cap/Flow Thru Dome
B
316SST
*D
High Pressure
V
303SS/Jorcote
DF
Double Diaphragm/Flow Thru Dome
W
316SS/Jorcote
F
Flow Thru Dome
X
303SS/Jorcote/Jordanic
*H
Handlwheel
Y
316SS/Jorcote/Jordanic
HF
Handwheel/Flow Thru Dome
HDF
Handwheel/Double Diaphragm/Flow Thru Dome
HP
High Pressure
5
Seat Material
A
6
* Available for Mark 63 and 64. Other options only
available for Mark 63.
Size
303SST
Cv
Kv
1
0.21
0,18
2
0.42
0,36
3
0.84
0,72
4
1.6
1,38
5
2.5
2,15
025
1/4" (DN8)
6
4.4
3,78
038
3/8" (DN12)
7
6.4
5,50
050
1/2" (DN15)
8
9.5
8,17
075
3/4" (DN20)
9
15
12,9
100
1" (DN25)
A
25
21,5
125
1-1/4" (DN32)
B
30
25,8
150
1-1/2" (DN40)
200
2" (DN50)
7&8
Range, PSI
MK63 1/4" - 3/4"
Body Material
MK63 1" - 2"
15
2-20 SST
05
1-5
DI
Ductile Iron
16
2-23
07
2-6 SST
BR
Bronze
37
10-38
20
3-8
CS
Carbon Steel (WCB)
43
15-35 SST
13
2-16 SST
S6
Stainless Steel (CF8M)
56
20-55
28
5-20
59
20-55
33
10-25 SST
74
30-85 SST
34
10-30
81
35-160
53
20-45
A6
95-220
75
30-95
97
60-160
1&2
End Connections
PT
NPT
BT
BSPT
BP
BSPP
SW
FSW
I5
150#IFE
F3
150#FE (Except IFE)
I3
300# IFE
F3
300#FE (Except IFE)
ZZ
Non-Standard
-5-
Mark 63/64 Differential Pressure Regulators
MK63/64/1214/5K/AB
Ordering Schematic (Con't)
Model
Options
Size
7&8
Body
Material
1
/
Range, psi
MK63HP
3
4
5
6
13&14
MK64
75-190
05
1-5
A7
100-320
10
2-12
A9
150-450
11
2-12 SST
17
2-25
18
2-25 SST
36
10-35
B3
10-35 SST
56
20-55
57
20-55 SST
63
20-80
87
40-115
70
25-160
80
30-180
7 8
9
10 11 12 13
14 15
Double Bolting
00
A1
9&10
2
15
None
Accessories
0
None
6
316SS Bolting
7
Hi-Temp Bolt
3
Bleed Port with Valve
4
Bleed Port Plugged
Z
Non-Standard
Diaphragm
S6
316 SST
VI
Viton
BN
Buna-N
JL
Jorlon
ZZ
Non-Standard
11&12
Actuator
MD
For Metal Diaphragm
ED
For Elastomer Diaphragm
ZZ
Non-Standard
Jordan Valve, a division of Richards Industries
3170 Wasson Road • Cincinnati, OH 45209
513.533.5600 • 800.543.7311 • 513.871.0105 (f)
[email protected] • www.jordanvalve.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement