LM2902, LM124, LM224, LM324 Datasheet PDF
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
LM124/LM224/LM324/LM2902 Low Power Quad Operational Amplifiers
Check for Samples: LM124-N, LM224-N, LM2902-N, LM324-N
FEATURES
1
•
2
•
•
•
•
Internally frequency compensated for unity
gain
Large DC voltage gain 100 dB
Wide bandwidth (unity gain) 1 MHz
– (temperature compensated)
Wide power supply range:
–
Single supply 3V to 32V
–
or dual supplies ±1.5V to ±16V
Very low supply current drain (700
μA)—essentially independent of supply
voltage
•
•
•
•
•
Low input biasing current 45 nA
– (temperature compensated)
Low input offset voltage 2 mV
– and offset current: 5 nA
Input common-mode voltage range includes
ground
Differential input voltage range equal to the
power supply voltage
Large output voltage swing 0V to V+ − 1.5V
DESCRIPTION
The LM124 series consists of four independent, high gain, internally frequency compensated operational
amplifiers which were designed specifically to operate from a single power supply over a wide range of voltages.
Operation from split power supplies is also possible and the low power supply current drain is independent of the
magnitude of the power supply voltage.
Application areas include transducer amplifiers, DC gain blocks and all the conventional op amp circuits which
now can be more easily implemented in single power supply systems. For example, the LM124 series can be
directly operated off of the standard +5V power supply voltage which is used in digital systems and will easily
provide the required interface electronics without requiring the additional ±15V power supplies.
UNIQUE CHARACTERISTICS
•
•
•
In the linear mode the input common-mode voltage range includes ground and the output voltage can also
swing to ground, even though operated from only a single power supply voltage
The unity gain cross frequency is temperature compensated
The input bias current is also temperature compensated
ADVANTAGES
•
•
•
•
•
Eliminates need for dual supplies
Four internally compensated op amps in a single package
Allows directly sensing near GND and VOUT also goes to GND
Compatible with all forms of logic
Power drain suitable for battery operation
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004, Texas Instruments Incorporated
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
www.ti.com
CONNECTION DIAGRAM
LM124A available per JM38510/11006
LM124 available per JM38510/11005
See STD Mil DWG 5962R99504 for Radiation Tolerant Device
Figure 1. Dual-In-Line Package Top View
SCHEMATIC DIAGRAM
(Each Amplifier)
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
ABSOLUTE MAXIMUM RATINGS (1)
LM124/LM224/LM324
LM2902
LM124A/LM224A/LM324A
Supply Voltage, V+
32V
26V
Differential Input Voltage
32V
26V
−0.3V to +32V
−0.3V to +26V
50 mA
50 mA
Molded DIP
1130 mW
1130 mW
Cavity DIP
1260 mW
1260 mW
Small Outline Package
800 mW
800 mW
Continuous
Continuous
Input Voltage
Input Current
(VIN < −0.3V)
(2)
Power Dissipation
(3)
Output Short-Circuit to GND
(One Amplifier)
(4)
V+ ≤ 15V and TA = 25°C
−40°C to +85°C
Operating Temperature Range
LM324/LM324A
0°C to +70°C
LM224/LM224A
−25°C to +85°C
LM124/LM124A
−55°C to +125°C
−65°C to +150°C
−65°C to +150°C
260°C
260°C
260°C
260°C
Vapor Phase (60 seconds)
215°C
215°C
Infrared (15 seconds)
220°C
220°C
Storage Temperature Range
Lead Temperature (Soldering, 10 seconds)
Soldering Information
Dual-In-Line Package
Soldering (10 seconds)
Small Outline Package
See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” for other methods of soldering surface mount devices.
ESD Tolerance
(1)
(2)
(3)
(4)
(5)
(5)
250V
250V
Refer to RETS124AX for LM124A military specifications and refer to RETS124X for LM124 military specifications.
This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of
the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is
also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the op amps to go to
the V+voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and
normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than −0.3V (at 25°C).
For operating at high temperatures, the LM324/LM324A/LM2902 must be derated based on a +125°C maximum junction temperature
and a thermal resistance of 88°C/W which applies for the device soldered in a printed circuit board, operating in a still air ambient. The
LM224/LM224A and LM124/LM124A can be derated based on a +150°C maximum junction temperature. The dissipation is the total of
all four amplifiers—use external resistors, where possible, to allow the amplifier to saturate of to reduce the power which is dissipated in
the integrated circuit.
Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
Human body model, 1.5 kΩ in series with 100 pF.
Copyright © 2004, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
3
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
www.ti.com
ELECTRICAL CHARACTERISTICS
V+ = +5.0V,
(1)
, unless otherwise stated
Parameter
Conditions
Input Offset Voltage
(2)
Input Bias Current
IIN(+) or IIN(−), VCM = 0V,
(3)
LM124A
Min
TA = 25°C
TA = 25°C
Input Offset Current
IIN(+) or IIN(−), VCM = 0V,
Typ
LM224A
Max Min
Typ
LM324A
Max Min
Typ
Max
Unit
s
1
2
1
3
2
3
mV
20
50
40
80
45
100
nA
2
10
2
15
5
30
nA
V+−1
.5
V
TA = 25°C
Input Common-Mode
Voltage Range
(4)
V+ = 30V, (LM2902, V+ = 26V),
V+−1
.5
0
V+−1
.5
0
0
TA = 25°C
Supply Current
Over Full Temperature Range
RL = ∞ On All Op Amps
+
mA
+
V = 30V (LM2902 V = 26V)
1.5
3
1.5
3
1.5
3
V+ = 5V
0.7
1.2
0.7
1.2
0.7
1.2
Large Signal
V+ = 15V, RL≥ 2kΩ,
Voltage Gain
(VO = 1V to 11V), TA = 25°C
Common-Mode
DC, VCM = 0V to V+ − 1.5V,
Rejection Ratio
TA = 25°C
Power Supply
V+ = 5V to 30V
Rejection Ratio
(LM2902, V+ = 5V to 26V),
50
100
50
100
25
100
V/m
V
70
85
70
85
65
85
dB
65
100
65
100
65
100
dB
−120
dB
TA = 25°C
Amplifier-to-Amplifier
Coupling
(5)
Output Current
−120
f = 1 kHz to 20 kHz, TA = 25°C
−120
(Input Referred)
Source
VIN+ = 1V, VIN− = 0V,
20
40
20
40
20
40
10
20
10
20
10
20
12
50
12
50
12
50
+
V = 15V, VO = 2V, TA = 25°C
Sink
VIN− = 1V, VIN+ = 0V,
mA
V+ = 15V, VO = 2V, TA = 25°C
VIN− = 1V, VIN+ = 0V,
μA
V+ = 15V, VO = 200 mV, TA = 25°C
Short Circuit to Ground
Input Offset Voltage
(6) +
V = 15V, TA = 25°C
RS = 0Ω
Input Offset Current
IIN(+) − IIN(−), VCM = 0V
IOS Drift
RS = 0Ω
(2)
(3)
(4)
(5)
(6)
4
60
40
4
VOS Drift
(1)
40
(2)
7
40
4
20
7
30
10
60
20
7
30
200
10
200
10
60
mA
5
mV
30
μV/°
C
75
nA
300
pA/°
C
These specifications are limited to −55°C ≤ TA ≤ +125°C for the LM124/LM124A. With the LM224/LM224A, all temperature
specifications are limited to −25°C ≤ TA ≤ +85°C, the LM324/LM324A temperature specifications are limited to 0°C ≤ TA ≤ +70°C, and
the LM2902 specifications are limited to −40°C ≤ TA ≤ +85°C.
VO ≃ 1.4V, RS = 0Ω with V+ from 5V to 30V; and over the full input common-mode range (0V to V+ − 1.5V) for LM2902, V+ from 5V to
26V.
The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V+ − 1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V
for LM2902), independent of the magnitude of V+.
Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This
typically can be detected as this type of capacitance increases at higher frequencies.
Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
ELECTRICAL CHARACTERISTICS (continued)
V+ = +5.0V, (1), unless otherwise stated
Parameter
Input Bias Current
IIN(+) or IIN(−)
Input Common-Mode
V+ = +30V
Voltage Range
LM124A
Conditions
(4)
Min
40
Typ
100
40
LM324A
Max Min
100
V+−2
0
Typ
40
0
Max
Unit
s
200
nA
V+−2
V
(LM2902, V+ = 26V)
V+ = +15V (VOSwing = 1V to 11V)
Voltage Gain
RL ≥ 2 kΩ
VOH
Swing
Output Current
Max Min
V+−2
0
Large Signal
Output Voltage
Typ
LM224A
25
25
V+ = 30V
RL = 2 kΩ
26
(LM2902, V+ = 26V)
RL = 10 kΩ
27
28
VIN+ = +1V,
10
20
VOL
V+ = 5V, RL = 10 kΩ
Source
VO = 2V
15
26
5
V/m
V
26
27
28
10
20
20
5
V
27
28
10
20
20
5
20
VIN− = 0V,
V+ = 15V
VIN− = +1V,
Sink
mV
mA
10
15
5
8
5
8
+
VIN = 0V,
V+ = 15V
Copyright © 2004, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
5
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
www.ti.com
ELECTRICAL CHARACTERISTICS
V+ = +5.0V,
(1)
, unless otherwise stated
Parameter
Conditions
Input Offset Voltage
(2)
Input Bias Current
IIN(+) or IIN(−), VCM = 0V,
(3)
LM124/LM224
Min
TA = 25°C
TA = 25°C
Input Offset Current
IIN(+) or IIN(−), VCM = 0V,
Typ
LM324
Max Min
Typ
LM2902
Max Min
Typ
Max
Unit
s
2
5
2
7
2
7
mV
45
150
45
250
45
250
nA
3
30
5
50
5
50
nA
V+−1
.5
V
TA = 25°C
Input Common-Mode
Voltage Range
(4)
V+ = 30V, (LM2902, V+ = 26V),
V+−1
.5
0
V+−1
.5
0
0
TA = 25°C
Supply Current
Over Full Temperature Range
RL = ∞ On All Op Amps
+
mA
+
V = 30V (LM2902 V = 26V)
1.5
3
1.5
3
1.5
3
V+ = 5V
0.7
1.2
0.7
1.2
0.7
1.2
Large Signal
V+ = 15V, RL≥ 2kΩ,
Voltage Gain
(VO = 1V to 11V), TA = 25°C
Common-Mode
DC, VCM = 0V to V+ − 1.5V,
Rejection Ratio
TA = 25°C
Power Supply
V+ = 5V to 30V
Rejection Ratio
(LM2902, V+ = 5V to 26V),
50
100
25
100
25
100
V/m
V
70
85
65
85
50
70
dB
65
100
65
100
50
100
dB
−120
dB
TA = 25°C
Amplifier-to-Amplifier
Coupling
(5)
Output Current
−120
f = 1 kHz to 20 kHz, TA = 25°C
−120
(Input Referred)
Source
VIN+ = 1V, VIN− = 0V,
20
40
20
40
20
40
10
20
10
20
10
20
12
50
12
50
12
50
+
V = 15V, VO = 2V, TA = 25°C
Sink
VIN− = 1V, VIN+ = 0V,
mA
V+ = 15V, VO = 2V, TA = 25°C
VIN− = 1V, VIN+ = 0V,
μA
V+ = 15V, VO = 200 mV, TA = 25°C
Short Circuit to Ground
Input Offset Voltage
(6) +
V = 15V, TA = 25°C
RS = 0Ω
Input Offset Current
IIN(+) − IIN(−), VCM = 0V
IOS Drift
RS = 0Ω
(2)
(3)
(4)
(5)
(6)
6
60
40
7
VOS Drift
(1)
40
(2)
60
40
9
7
7
100
10
mA
10
mV
μV/°
C
7
150
10
60
45
10
200
nA
pA/°
C
These specifications are limited to −55°C ≤ TA ≤ +125°C for the LM124/LM124A. With the LM224/LM224A, all temperature
specifications are limited to −25°C ≤ TA ≤ +85°C, the LM324/LM324A temperature specifications are limited to 0°C ≤ TA ≤ +70°C, and
the LM2902 specifications are limited to −40°C ≤ TA ≤ +85°C.
VO ≃ 1.4V, RS = 0Ω with V+ from 5V to 30V; and over the full input common-mode range (0V to V+ − 1.5V) for LM2902, V+ from 5V to
26V.
The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V+ − 1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V
for LM2902), independent of the magnitude of V+.
Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This
typically can be detected as this type of capacitance increases at higher frequencies.
Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
ELECTRICAL CHARACTERISTICS (continued)
V+ = +5.0V, (1), unless otherwise stated
Parameter
Input Bias Current
IIN(+) or IIN(−)
Input Common-Mode
V+ = +30V
Voltage Range
LM124/LM224
Conditions
(4)
Min
40
Typ
300
40
LM2902
Max Min
500
V+−2
0
Typ
40
0
Max
Unit
s
500
nA
V+−2
V
(LM2902, V+ = 26V)
V+ = +15V (VOSwing = 1V to 11V)
Voltage Gain
RL ≥ 2 kΩ
VOH
Swing
Output Current
Max Min
V+−2
0
Large Signal
Output Voltage
Typ
LM324
25
15
V+ = 30V
RL = 2 kΩ
26
(LM2902, V+ = 26V)
RL = 10 kΩ
27
28
VIN+ = +1V,
10
20
VOL
V+ = 5V, RL = 10 kΩ
Source
VO = 2V
15
26
5
V/m
V
22
27
28
10
20
20
5
V
23
24
10
20
20
5
100
VIN− = 0V,
V+ = 15V
VIN− = +1V,
Sink
mV
mA
5
8
5
8
5
8
+
VIN = 0V,
V+ = 15V
Copyright © 2004, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
7
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS
8
Input Voltage Range
Input Current
Supply Current
Voltage Gain
Open Loop Frequency
Response
Common Mode Rejection
Ratio
Voltage Follower Pulse
Response
Voltage Follower Pulse
Response (Small Signal)
Large Signal Frequency
Response
Output Characteristics
Current Sourcing
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Output Characteristics
Current Sinking
Current Limiting
Input Current (LM2902 only)
Voltage Gain (LM2902 only)
APPLICATION HINTS
The LM124 series are op amps which operate with only a single power supply voltage, have true-differential
inputs, and remain in the linear mode with an input common-mode voltage of 0 VDC. These amplifiers operate
over a wide range of power supply voltage with little change in performance characteristics. At 25°C amplifier
operation is possible down to a minimum supply voltage of 2.3 VDC.
The pinouts of the package have been designed to simplify PC board layouts. Inverting inputs are adjacent to
outputs for all of the amplifiers and the outputs have also been placed at the corners of the package (pins 1, 7, 8,
and 14).
Precautions should be taken to insure that the power supply for the integrated circuit never becomes reversed in
polarity or that the unit is not inadvertently installed backwards in a test socket as an unlimited current surge
through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a
destroyed unit.
Large differential input voltages can be easily accommodated and, as input differential voltage protection diodes
are not needed, no large input currents result from large differential input voltages. The differential input voltage
may be larger than V+ without damaging the device. Protection should be provided to prevent the input voltages
from going negative more than −0.3 VDC (at 25°C). An input clamp diode with a resistor to the IC input terminal
can be used.
To reduce the power supply drain, the amplifiers have a class A output stage for small signal levels which
converts to class B in a large signal mode. This allows the amplifiers to both source and sink large output
currents. Therefore both NPN and PNP external current boost transistors can be used to extend the power
capability of the basic amplifiers. The output voltage needs to raise approximately 1 diode drop above ground to
bias the on-chip vertical PNP transistor for output current sinking applications.
For ac applications, where the load is capacitively coupled to the output of the amplifier, a resistor should be
used, from the output of the amplifier to ground to increase the class A bias current and prevent crossover
distortion.
Where the load is directly coupled, as in dc applications, there is no crossover distortion.
Capacitive loads which are applied directly to the output of the amplifier reduce the loop stability margin. Values
of 50 pF can be accommodated using the worst-case non-inverting unity gain connection. Large closed loop
gains or resistive isolation should be used if larger load capacitance must be driven by the amplifier.
Copyright © 2004, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
9
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
www.ti.com
The bias network of the LM124 establishes a drain current which is independent of the magnitude of the power
supply voltage over the range of from 3 VDC to 30 VDC.
Output short circuits either to ground or to the positive power supply should be of short time duration. Units can
be destroyed, not as a result of the short circuit current causing metal fusing, but rather due to the large increase
in IC chip dissipation which will cause eventual failure due to excessive junction temperatures. Putting direct
short-circuits on more than one amplifier at a time will increase the total IC power dissipation to destructive
levels, if not properly protected with external dissipation limiting resistors in series with the output leads of the
amplifiers. The larger value of output source current which is available at 25°C provides a larger output current
capability at elevated temperatures (see typical performance characteristics) than a standard IC op amp.
The circuits presented in the section on typical applications emphasize operation on only a single power supply
voltage. If complementary power supplies are available, all of the standard op amp circuits can be used. In
general, introducing a pseudo-ground (a bias voltage reference of V+/2) will allow operation above and below this
value in single power supply systems. Many application circuits are shown which take advantage of the wide
input common-mode voltage range which includes ground. In most cases, input biasing is not required and input
voltages which range to ground can easily be accommodated.
TYPICAL SINGLE-SUPPLY APPLICATIONS
(V+ = 5.0 VDC)
*R not needed due to temperature independent IIN
Figure 2. Non-Inverting DC Gain (0V Input = 0V Output)
Where: V0 = V1 + V2 − V3 − V4
(V1 + V2) ≥ (V3 + V4) to keep VO > 0 VDC
Figure 3. DC Summing Amplifier
(VIN'S ≥ 0 VDC and VO ≥ VDC)
10
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
(V+ = 5.0 VDC)
V0 = 0 VDC for VIN = 0 VDC
AV = 10
Figure 4. Power Amplifier
Figure 5. LED Driver
fo = 1 kHz
Q = 50
AV = 100 (40 dB)
Figure 6. “BI-QUAD” RC Active Bandpass Filter
Copyright © 2004, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
11
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
www.ti.com
(V+ = 5.0 VDC)
Figure 7. Fixed Current Sources
Figure 8. Lamp Driver
*(Increase R1 for IL small)
Figure 9. Current Monitor
12
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
(V+ = 5.0 VDC)
Figure 10. Driving TTL
Figure 11. Voltage Follower
Figure 12.
Figure 13. Pulse Generator
Figure 14. Squarewave Oscillator
Copyright © 2004, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
13
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
www.ti.com
(V+ = 5.0 VDC)
Figure 15. Pulse Generator
IO = 1 amp/volt VIN
(Increase RE for Io small)
Figure 16. High Compliance Current Sink
Figure 17. Low Drift Peak Detector
14
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
(V+ = 5.0 VDC)
Figure 18. Comparator with Hysteresis
VO = VR
Figure 19. Ground Referencing a Differential Input Signal
*Wide control voltage range: 0 VDC ≤ VC ≤ 2 (V+ −1.5 VDC)
Figure 20. Voltage Controlled Oscillator Circuit
Figure 21. Photo Voltaic-Cell Amplifier
Copyright © 2004, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
15
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
www.ti.com
(V+ = 5.0 VDC)
Figure 22. AC Coupled Inverting Amplifier
Figure 23. AC Coupled Non-Inverting Amplifier
16
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
(V+ = 5.0 VDC)
fO = 1 kHz
Q=1
AV = 2
Figure 24. DC Coupled Low-Pass RC Active Filter
Figure 25. High Input Z, DC Differential Amplifier
Copyright © 2004, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
17
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
www.ti.com
(V+ = 5.0 VDC)
Figure 26. High Input Z Adjustable-Gain DC Instrumentation Amplifier
Figure 27. Using Symmetrical Amplifiers to Reduce Input Current (General Concept)
18
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
(V+ = 5.0 VDC)
Figure 28. Bridge Current Amplifier
fO = 1 kHz
Q = 25
Figure 29. Bandpass Active Filter
Copyright © 2004, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
19
PACKAGE OPTION ADDENDUM
www.ti.com
12-Nov-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package Qty
Drawing
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Samples
(3)
(Requires Login)
LM124AJ/PB
ACTIVE
CDIP
J
14
25
TBD
A42 SNPB
Level-1-NA-UNLIM
LM124J/PB
ACTIVE
CDIP
J
14
25
TBD
A42 SNPB
Level-1-NA-UNLIM
LM224J
ACTIVE
CDIP
J
14
25
TBD
A42 SNPB
Level-1-NA-UNLIM
LM2902M
ACTIVE
SOIC
D
14
55
TBD
CU SNPB
Level-1-235C-UNLIM
LM2902M/NOPB
ACTIVE
SOIC
D
14
55
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM2902MT
ACTIVE
TSSOP
PW
14
94
TBD
CU SNPB
Level-1-260C-UNLIM
LM2902MT/NOPB
ACTIVE
TSSOP
PW
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM2902MTX
ACTIVE
TSSOP
PW
14
2500
TBD
CU SNPB
Level-1-260C-UNLIM
LM2902MTX/NOPB
ACTIVE
TSSOP
PW
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM2902MX
ACTIVE
SOIC
D
14
2500
TBD
CU SNPB
Level-1-235C-UNLIM
LM2902MX/NOPB
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM2902N/NOPB
ACTIVE
PDIP
NFF
14
25
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM2902N/PB
ACTIVE
PDIP
NFF
14
25
TBD
CU SNPB
Level-1-NA-UNLIM
LM324AM
ACTIVE
SOIC
D
14
55
TBD
CU SNPB
Level-1-235C-UNLIM
LM324AM/NOPB
ACTIVE
SOIC
D
14
55
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM324AMX
ACTIVE
SOIC
D
14
2500
TBD
CU SNPB
Level-1-235C-UNLIM
LM324AMX/NOPB
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM324AN/NOPB
ACTIVE
PDIP
NFF
14
25
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM324AN/PB
ACTIVE
PDIP
NFF
14
25
TBD
Call TI
Level-1-NA-UNLIM
LM324J
ACTIVE
CDIP
J
14
25
TBD
A42 SNPB
Level-1-NA-UNLIM
LM324M
ACTIVE
SOIC
D
14
55
TBD
CU SNPB
Level-1-235C-UNLIM
LM324M/NOPB
ACTIVE
SOIC
D
14
55
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM324MT
ACTIVE
TSSOP
PW
14
94
TBD
CU SNPB
Level-1-260C-UNLIM
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
12-Nov-2012
Orderable Device
Status
(1)
Package Type Package Pins Package Qty
Drawing
LM324MT/NOPB
ACTIVE
TSSOP
PW
14
94
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Samples
(3)
(Requires Login)
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM324MTX
ACTIVE
TSSOP
PW
14
2500
TBD
CU SNPB
Level-1-260C-UNLIM
LM324MTX/NOPB
ACTIVE
TSSOP
PW
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM324MX
ACTIVE
SOIC
D
14
2500
TBD
CU SNPB
Level-1-235C-UNLIM
LM324MX/NOPB
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM324N/NOPB
ACTIVE
PDIP
NFF
14
25
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
LM324N/PB
ACTIVE
PDIP
NFF
14
25
TBD
Call TI
Level-1-NA-UNLIM
MLM324P
ACTIVE
PDIP
NFF
14
25
TBD
Call TI
Level-1-NA-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
12-Nov-2012
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
15-Nov-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
8.3
1.6
8.0
12.0
Q1
LM2902MTX
TSSOP
PW
14
2500
330.0
12.4
6.95
LM2902MTX/NOPB
TSSOP
PW
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2902MX
SOIC
D
14
2500
330.0
16.4
6.5
9.35
2.3
8.0
16.0
Q1
LM2902MX/NOPB
SOIC
D
14
2500
330.0
16.4
6.5
9.35
2.3
8.0
16.0
Q1
LM324AMX
SOIC
D
14
2500
330.0
16.4
6.5
9.35
2.3
8.0
16.0
Q1
LM324AMX/NOPB
SOIC
D
14
2500
330.0
16.4
6.5
9.35
2.3
8.0
16.0
Q1
LM324MTX
TSSOP
PW
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM324MTX/NOPB
TSSOP
PW
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM324MX
SOIC
D
14
2500
330.0
16.4
6.5
9.35
2.3
8.0
16.0
Q1
LM324MX/NOPB
SOIC
D
14
2500
330.0
16.4
6.5
9.35
2.3
8.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
15-Nov-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM2902MTX
TSSOP
PW
14
2500
349.0
337.0
45.0
LM2902MTX/NOPB
TSSOP
PW
14
2500
349.0
337.0
45.0
LM2902MX
SOIC
D
14
2500
349.0
337.0
45.0
LM2902MX/NOPB
SOIC
D
14
2500
349.0
337.0
45.0
LM324AMX
SOIC
D
14
2500
349.0
337.0
45.0
LM324AMX/NOPB
SOIC
D
14
2500
349.0
337.0
45.0
LM324MTX
TSSOP
PW
14
2500
349.0
337.0
45.0
LM324MTX/NOPB
TSSOP
PW
14
2500
349.0
337.0
45.0
LM324MX
SOIC
D
14
2500
349.0
337.0
45.0
LM324MX/NOPB
SOIC
D
14
2500
349.0
337.0
45.0
Pack Materials-Page 2
MECHANICAL DATA
NFF0014A
N0014A
N14A (Rev G)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement