Super mm @B'NSTRUCTION MANUAL
Frontior- 20
— . atl = —
nn EEE
0.20-0.25 cu.in. displacement 2-cycle
0.26 cu.in. displacement 4-cycle
Radio required : 4 channels, 4 servos airplane radio
Г _a Specifications
Wing Span 54.0 in/ 1350mm
Wing Area 496 sq in / 32 sq dm
Flying Weight 3.5-4.0 165 / 1500-1700g
Fuselage Length 44.0 in / 1170mm
* Specifications are subject to change without notice.”
Warning !This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of engine powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual
at hand for quick reference.
THE WORLD MODELS
MANUFACTURINGCO. LTD.
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
www. theworldmodels.com
Super
Frontior - 20
INDEX
BEFORE YOU BEGIN ------====================ennnnnnanananananaaaa—a P. 1
PARTS LIST --------sscssssmmmmemnnnnnnnnnnnnnn snes snes. P.2
ASSEMBLY ---=-==-=- eee P.3-10
SAFETY PRECAUTIONS ----------======eccacancnnannnananannnnnnn P.11
BEFORE YOU BEGIN
ib Read through the manual before you begin, so you will have an overall idea of what to do.
2) Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT
and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you
find to be defective alter the gluing process may be difficult to remove for warranty replacement. The
manufacturer will replace any defective parts. but will be difficult to extend to the good parts that are
good before gluing to defective parts during assembly.
к) Symbols used throughout this instruction manual comprise of the following : -
Apply instant glue
AB Apply epoxy glue. (C.A.glue, super glue.)
L R Assemble left and right N Ensure smooth non-binding
/ sides the same way. à À movement while assembling.
Peel off shaded portion
covering film. Cut off shaded portion.
Drill holes with the specified
diameter (here: 3mm). Must be purchased separately!
Warning!
Do not overlook this symbol!
Pay close attention here!
Pierce the shaded portion
covering film.
DU o ern
1. FUSELAGE - 1 pc
2. MAIN WING (wWing Joiner) — 1 pair
3. STABILIZER & ELEVATOR ~ 1 set
4 VERTICAL FIN & RUDDER ~ 1 set
5. ENGINE MOUNT PL5111-030 — 1 set
6.SPINNER 245mm - 1 pc
7.FUEL TANK 200cc — 1 set
8.WHEEL 950mm — 3 pcs
9.SPONGE 75x75x70mm
(For Radio Equipment) — 1 pc
10.FRONT LANDING GEAR — 1 pc
11. MAIN LANDING GEAR - 1 pair
12.PUSHROD:-
WOODEN ROD 26x300mm (For Rudder Servo) — 1 pc
WOODEN ROD 06x420mm (For Elevator Servo) — 1 pc
METAL ROD 01.8x175mm (For Rudder Servo) - 1 pc
METAL ROD 91.8x175mm (For Elevator Servo) - 1 pc
14 WOODEN PARTS:—
BALSA 7x8x30mm (For Aileron Servo) — 1 pc
PLYWOOD (Fin TiP) 10x39mm = 1 pc
PLYWOOD 144x64mm (For Fixing Stabilizer) - 1 pc
PLYWOOD 2x20x55mm (Wing Protection) — 1 pc
PLYWOOD 3x8x30mm (For Aileron Servo) - 2 pcs
PLYWOOD 10x10x71mm (For Fixing Fuel Tank) — 1 pc
WOODEN ROD 26x115mm (For Fixing Wing) - 2 pcs
WING JOINER 9x20.5x140mm — 1 pc
15.PLASTIC PARTS: ~
STRAPER (FOR AILERON & ELEVATOR SERVO) - 3 pcs
PLASTIC RING (FOR AILERON HORN) ~ 2 pcs
HORN (FOR RUDDER & ELEVATOR) —- 2 sets
STEERING ARM (FOR FRONT WHEEL) - 1 pc
PLASTIC PLATE (FOR MAIN LANDING GEAR) 2 pcs
CLEVIS - 4 pcs
16.METAL PARTS:—
METAL ROD 81.8x250mm w/Threads (For Rudder Servo) — 1 pc
METAL ROD 01.8x130mm w/Threads (For Elevator Servo) -1 pc _ WASHER d3xD12mm — 4 pcs
METAL ROD 01.8x130mm wThreads (For Aileron Servo) -2 pcs
METAL ROD 01.2x400mm (For Front Wheel & Throttie) - 2 pcs
13.PUSHWIRE:-
FRONT WHEEL & THROTTLE PUSHWIRE
d2xD3x300mm - 2 pcs
NUT 3mm — 10 pes
LINKAGE CONNECTOR 2.1mm - 3 sets
COLLAR 3.1mm -— 8 pcs
SCREW PA3x12mm —4 pcs
SCREW PM2x12mm - 4 pcs
SCREW PM3x16mm — 2 pcs
SCREW PM3x22mm — 4 pcs
SCREW PM3x25mm — 4 pcs
WASHER d3xD7mm — 12 pcs
17.FUEL TUBE 96x5mm -— 7 pcs
HEAT - SHRINK TUBE 06x40mm —4 pcs
18.RUBBER BAND 60x4mm - 8 pcs
19.DECALS PN:ST200015 — 1 set
р. 2
Р-Я
3 ИТ:
@ Vain Wing)
A 7 Cut out to fit in the aileron servo
d
“y Main Wing) Ei Warning!
Securely glue together. If coming
off during flights, you lose control
of your airplane which leads to
Cut out the Monokote.
accidents!
2x20x55mm
P.3
a Aileron Servo)
Fuel Tube
06x5mm
e ) -
E #7 Balsa 7x8x30mm
а.
a Vertical Fin / Stabilizer)
|
=
а
\\ \
\
AB
( vertical Fin/ Stabilizer)
PM3x16mm Screw
EXENTOS 2
d2 x D12mm Washer
4
3mm Nut PM3x16mm 5
OR — * d3xD12mm
Do
NN
| 7
“= “че Ганя
lá d2xD12mm
> 3mm Nut
P.4
Engine Mount)
PM3x 22mm Screw
| EID
d3xD7mm Washer
4
4
Engine Mount
PL5111-030
cu 5
vd a £
yA
8 Front Wheel)
3mm Set Screw
| 4
3.1mm Collar
3mm Set Screw
3.1mm Collar
Completed
Fuel Tank 200cc
F A
Install plywood 10x10x71mm
(For fixing fuel tank)
Fuel Tank
8 Top View
A
PD
a Engine)
PM3x 25mm Screw
| E 4
imm Washer
8
3mm Nut
r
Spinner
T1
Install Engine Position |
N 3x25mm
@ If the engine throttle control is
on the opposite side, install the
throttle pushwire accordingly.
install the throttle servo with the
drive pinion on the same side of
throttle pushwire.
Raise throttle servo if necessary
to provide clearance between
throttle and front wheel push-
wires.
Landing Gear)
PA3 x12 Screw
| 4
PA3x12mm
PA3x12mm
12 Landing Gear)
imm Set Screw
4
3.1mm Collar
в i
| 4
+——#
Ea sq A
ii 3
в +
в a
— —
3mm Set
Screw
250mm
3.1mm Collar
Jar
P.6
Rudder Pushrod)
01.8x175mm
Fuel Tube
Heat-shrink Tube
x A
7
”
PA zo
ban” Be careful not to scorch
the heat-shrink tube!
_
- 600mm e
| — À 1 I
COMPLETED
Elevator Pushrod) el Tube
06x5mm
Ox Sm Heat-shrink Tube
a
-
Je
a
or
„т
a Be careful not to scorch
the heat-shrink tube!
- 660mm +
№ В 1 |
COMPLETED
LINKAGE CONNECTOR
i Set Screw а
Linkage Connector
: = =m Included with the Radio Set.
2mm Nut e
o
2mm Washer
O
Co
Throttle Servo,
М.!. Rudder Servo,
Front Wheel Servo.
Н Please refer to attached sheet for linkage connector installation.
e
и
Radio Equipment) DA | | Elevator Pushrod
| Fuel Tube —
E.
E
Rudder Pushrod
Radio Equ ipme nt) O Install and arrange the servo as shown in the diagram
Throttle Servo
Elevator Servo
Fuel Tank
Rudder Servo
Receiver/Battery
sponge sheet DEI
715x75x70mm
& Rudder Pushrod)
PM2 x 12mm Screw
ame
2
Pm Rudder Pushrod $ |
e
PM2x12mm
P.8
Elevator Pushrod)
PM2x 12mm Screw
gE — — 2
fl À
UE Line up the holes —
7] of the horn to the
a
7
levator Pushroc
PM2x12mm
Plastic clevis
Fuel Tube VA ; Horn
-6x5mm 7 Lo
7 A
> обе
7 To
e Bottom View \_ РОДЫ 4
Main Wing)
=
Equal length on both
sides, then apply CA
glue.
Wooden Rod
26x115mm
Main Wing)
D60x4mm Rubber Band
8
Fi To hold tightly, two rubber bands are
needed together for each mounting.
Rubber Band In total, eight rubber bands are used
x2 for this step.
© Z7
S 7 al
N
P.9
Adjust the wing and fuselage configuration
as in the diagram.
PE
Late
Te. AN
B B'
A=A с С"
В = В'
C=C
23 Control Th rows) Adjust the control throws as shown in
the diagram. These throws are good for
general flying. You can adjust according
Rudder —— to your personal preference.
( Y Li
EZ {25mm
Elevator mr
( 2 "15mm
es 15mm
Aileron
221 C.G) The ideal C.G. position is 75mm(2.95 in)behind
the leading edge measured at where the wing
meets the fuselage. In order to obtain the C.G.
specified, add weight to the fuselage or move
the battery position. Check the C.G. before
flying.
les 75mm
| 2.95in
+
O ca.
/
P.10
E Warming!
Important Safety Precautions
#First time flyer should never fly by himself / herself. Assistance from experienced flyer is
absolutely necessary.
#Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
#SUPER FRONTIER-20 is specially designed to be powered by 2C 20-25 or 4C 26 engine,
using a more powerful engine does not mean better performance. In fact, over powered
engine may cause severe damage and injuries.
#Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller.
#If you find wrinkles on the covering as a result of weather changes, you can use hot iron
to remove the wrinkles. Please begin with lower temperature setting and NT raise
the temperature until the wrinkles are gone. Too hot an iron may damage the covering.
#Check and re-tighten up all factory assembled screws, use thread locker if applicable.
A038R0402
P.11
">
