Allied Telesyn International Corp | AT-8324SX | Install guide | Allied Telesyn International Corp AT-8324SX Install guide

AT-B15/SX
AT-B15/LX
AT-B17
Expansion
Modules
For the AT-8324SX Fast Ethernet
Switch
Quick Install Guide
PN 613-50113-00 Rev A
Copyright  2000 Allied Telesyn International, Corp.
960 Stewart Drive Suite B, Sunnyvale CA 94086 USA
All rights reserved. No part of this publication may be reproduced without prior
written permission from Allied Telesyn International, Corp.
Ethernet is a registered trademark of Xerox Corporation. All other product names,
company names, logos or other designations mentioned herein are trademarks or
registered trademarks of their respective owners.
Allied Telesyn International, Corp. reserves the right to make changes in specifications
and other information contained in this document without prior written notice. The
information provided herein is subject to change without notice. In no event shall
Allied Telesyn International, Corp. be liable for any incidental, special, indirect, or
consequential damages whatsoever, including but not limited to lost profits, arising out
of or related to this manual or the information contained herein, even if Allied Telesyn
International Corp. has been advised of, known, or should have known, the possibility of
such damages.
Electrical Safety and Emission Statement
Standards: This product meets the following standards.
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with this instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the
FCC, can void your right to operate this equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur
le matériel brouilleur du Canada.
RFI Emission
EN55022 Class A (CISPR 22) ! 1
EN60555-2 (1995) Class A
EN60555-3
WARNING: In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures. ! 2
Immunity
IEC 1000-4-2 (4 kV CD, 8 kV AD) ! 3
IEC 1000-4-3 (1995) (3 V/m)
IEC 1000-4-4 (1995) (1.0 kV - (power line);
0.5 kV - (signal line))
IEC 1000-4-6 (1995) (3 Vrms)
EN50082-1 (1992)
EN61000-4-2 (1995)
EN61000-4-4 (1995)
Important: Appendix A contains translated safety statements for installing this
equipment. When you see the !, go to Appendix A for the translated safety statement in
your language.
Wichtig: Anhang A enthält übersetzte Sicherheitshinweise für die Installation dieses
Geräts. Wenn Sie ! sehen, schlagen Sie in Anhang A den übersetzten
Sicherheitshinweis in Ihrer Sprache nach.
Vigtigt: Tillæg A indeholder oversatte sikkerhedsadvarsler, der vedrører installation af
dette udstyr. Når De ser symbolet !, skal De slå op i tillæg A og finde de oversatte
sikkerhedsadvarsler i Deres eget sprog.
Belangrijk: Appendix A bevat vertaalde veiligheidsopmerkingen voor het installeren van
deze apparatuur. Wanneer u de ! ziet, raadpleeg Appendix A voor vertaalde
veiligheidsinstructies in uw taal.
Important: L'annexe A contient les instructions de sécurité relatives à l'installation de cet
équipement. Lorsque vous voyez le symbole !, reportez-vous à l'annexe A pour consulter
la traduction de ces instructions dans votre langue.
Tärkeää: Liite A sisältää tämän laitteen asentamiseen liittyvät käännetyt turvaohjeet.
Kun näe !-symbolin, katso käännettyä turvaohjetta liitteestä A.
Importante: l’Appendice A contiene avvisi di sicurezza tradotti per l’installazione di
questa apparecchiatura. Il simbolo !, indica di consultare l’Appendice A per l’avviso di
sicurezza nella propria lingua.
iii
Viktig: Tillegg A inneholder oversatt sikkerhetsinformasjon for installering av dette
utstyret. Når du ser !, åpner du til Tillegg A for å finne den oversatte
sikkerhetsinformasjonen på ønsket språk.
Importante: O Anexo A contém advertências de segurança traduzidas para instalar este
equipamento. Quando vir o símbolo !, leia a advertência de segurança traduzida no seu
idioma no Anexo A.
Importante: El Apéndice A contiene mensajes de seguridad traducidos para la
instalación de este equipo. Cuando vea el símbolo !, vaya al Apéndice A para ver el
mensaje de seguridad traducido a su idioma.
Obs! Bilaga A innehåller översatta säkerhetsmeddelanden avseende installationen av
denna utrustning. När du ser !, skall du gå till Bilaga A för att läsa det översatta
säkerhetsmeddelandet på ditt språk.
iv
Table of Contents
Electrical Safety and Emission Statement ..............................................iii
Table of Contents ........................................................................................... v
Welcome to Allied Telesyn ......................................................................... vii
Where to Find Web-based Guides.................................................................... vii
Document Conventions..................................................................................... vii
Contacting Allied Telesyn ............................................................................... viii
Online Support ......................................................................................... viii
For Technical Support and Services........................................................ viii
Technical Support E-mail Addresses ......................................................viii
Returning Products............................................................................................ ix
FTP Server ......................................................................................................... ix
For Sales or Corporate Information................................................................... x
Tell Us What You Think..................................................................................... x
Overview .......................................................................................................... 1
Installing the Expansion Module....................................................................... 2
Verifying the Package Contents ................................................................. 2
Reviewing Safety Guidelines ...................................................................... 3
Reviewing Connectivity Guidelines............................................................ 4
Handling the Module................................................................................... 5
Installing the Module .................................................................................. 5
LEDs.................................................................................................................... 8
Troubleshooting .................................................................................................. 8
Warranty Registration ....................................................................................... 8
Technical Specifications ..................................................................................... 9
Appendix A
Translated Safety and Emission Information ....................................... 11
Appendix B
Technical Support Fax Order ................................................................... 23
Incident Summary ............................................................................................ 23
Appendix C
AT-B15 and AT-B17 Quick Install Guide Feedback ............................. 25
v
Welcome to Allied Telesyn
This guide contains instructions on how to install an AT-B15/SX, AT-B15/LX,
or AT-B17 expansion module in an AT-8324SX Fast Ethernet Switch.
Where to Find Web-based Guides
The Allied Telesyn web site at www.alliedtelesyn.com provides you with an
easy way to access the most recent documentation and technical information
for all of our products. All web-based documents relating to this product and
other Allied Telesyn products can be downloaded from the web site in pdf
format.
Document Conventions
This guide uses several conventions that you should become familiar with first
before you begin to install the product.
Note
A note provides additional information.
Caution
A caution indicates that performing or omitting a specific action may
result in equipment damage or loss of data.
Warning
A warning indicates that performing or omitting a specific action
may result in bodily injury.
vii
Contacting Allied Telesyn
There are several ways to contact Allied Telesyn technical support: online,
telephone, fax and e-mail.
Online Support
You can request technical support online by filling out the Tech-Assistant
Form at www.alliedtelesyn.com/support.htm.
For Technical Support and Services
Americas
United States, Canada, Mexico,
Central America, South America
Tel:
1 (800) 428-4835, option 4
Fax: 1 (503) 639-3176
Germany
Germany, Switzerland, Austria, Eastern
Europe
Tel: (+49) 0130/83-56-66
Fax: (+49) 30-435-900-115
Asia
Singapore, Taiwan, Thailand, Malaysia,
Indonesia, Korea, Philippines, China,
India, Hong Kong
Tel: (+65) 381-5612
Fax: (+65) 383-3830
Italy
Italy, Spain, Portugal, Greece, Turkey,
Israel
Tel: (+39) 02-416047
Fax: (+39) 02-419282
Australia
Tel: 1 (800) 000-880
Fax: (+61) 2-9438-4966
Japan
Tel: (+81) 3-3443-5640
Fax: (+81) 3-3443-2443
France
France, Belgium, Luxembourg,
The Netherlands, Middle East, Africa
Tel: (+33) 0-1-60-92-15-25
Fax: (+33) 0-1-69-28-37-49
United Kingdom
United Kingdom, Denmark, Norway,
Sweden, Finland
Tel: (+0044) 1235-442500
Fax: (+44) 1-235-442680
Technical Support E-mail Addresses
United States and Canada
TS1@alliedtelesyn.com
Latin America, Mexico, Puerto Rico, Caribbean, and Virgin Islands
latin_america@alliedtelesyn.com
United Kingdom, Sweden, Norway, Denmark, and Finland
support_europe@alliedtelesyn.com
viii
AT-B15 and AT-B17 Quick Install Guide
Returning Products
Products for return or repair must first be assigned a Return Materials
Authorization (RMA) number. A product sent to Allied Telesyn without a
RMA number will be returned to the sender at the sender’s expense.
To obtain an RMA number, contact Allied Telesyn’s Technical Support at one
of the following locations:
North America
2205 Ringwood Ave
San Jose, CA 95131
Tel: 1-800-428-4835, option 4
Fax: 1-503-639-3716
European Customer Support Centre
10/11 Bridgemead Close
Westmead Industrial Estate
Swindon, Wiltshire SN5 7YT
England
Tel: +44-1793-501401
Fax: +44-1793-431099
Latin America, the Caribbean,
Virgin Islands
Tel: international code + 425-481-3852
Fax: international code + 425-483-9458
Mexico and Puerto Rico
Tel: 1-800-424-5012, ext 3852 or
1-800-424-4284, ext 3852
Mexico only: 95-800-424-5012, ext 3852
Fax: international code + 425-489-9191
FTP Server
If you know the name of a specific driver that you need for an Allied Telesyn
device, you can download the software by connecting directly to our FTP
server at ftp://gateway.centre.com.
At login, enter ‘anonymous’. Enter your e-mail address for the password as
requested by the server at login.
ix
For Sales or Corporate Information
Allied Telesyn International, Corp.
19800 North Creek Parkway, Suite 200
Bothell, WA 98011
Tel: 1 (425) 487-8880
Fax: 1 (425) 489-9191
Allied Telesyn International, Corp.
960 Stewart Drive, Suite B
Sunnyvale, CA 94086
Tel: 1 (800) 424-4284 (USA and Canada)
Fax: 1 (408) 736-0100
Tell Us What You Think
If you have any comments or suggestions on how we might improve this or
other Allied Telesyn documents, please fill out the “AT-B15 and AT-B17 Quick
Install Guide Feedback” on page 25 and return the form to us at the address
or fax number provided. You can also provide feedback online by filling out the
Feedback on Documentation form at www.alliedtelesyn.com/forms/
feedbackman.htm.
x
Overview
The AT-B15/SX, AT-B15/LX, and AT-B17/SM are optional expansion modules
for the AT-8324SX Fast Ethernet Switch. These expansion modules can be
used to extend your network to remote sites, build a Fast Ethernet or Gigabit
Ethernet backbone, or connect additional nodes to the network, such as highspeed servers.
Table 1 lists the basic specifications of the modules.
Table 1 Expansion Modules
Model
Number and Type of Ports
Maximum Distance1
AT-B15/SX
One 1000BASE-SX port
550 m (1805 ft)
AT-B15/LX
One 1000BASE-LX port
5 km (3 mi)
AT-B17
Two 100BASE-FX ports
2 km (1.24 mi)
1. The maximum distance can be less depending on the type of fiber optic cabling used with the port
and the duplex mode of the end node.
Caution
The expansion modules are designed for the AT-8324SX Fast Ethernet
Switch only. Do not install these modules in any other Allied Telesyn
device.
1
Figure 1 through Figure 3 illustrate the expansion modules.
Figure 1 AT-B15/SX Expansion Module
Figure 2 AT-B15/LX Expansion Module
Figure 3 AT-B17 Expansion Module
Installing the Expansion Module
The following sections contain the instructions on how to install an expansion
module in the switch.
Verifying the Package Contents
Check to be sure that your module package contains the following items. If
any of the items are missing or damaged, contact your Allied Telesyn
representative.
2
"
One AT-B15/SX, AT-B15/LX, or AT-B17 Expansion Module
"
Warranty Card
"
This Quick Install Guide
AT-B15 and AT-B17 Quick Install Guide
Reviewing Safety Guidelines
Please review the following safety guidelines before you begin to install the
expansion module in the switch.
Warning
Class 1 laser product. ! 4
Warning
Do not stare into the laser beam. ! 5
Warning
Electric Shock Hazard: To prevent electric shock, do not remove the
cover. There are no user-serviceable parts inside. The unit contains
hazardous voltages and should only be opened by a trained and
qualified technician. ! 6
Warning
Lightning Danger: Do not work on this equipment or cables during
periods of lightning activity. ! 7
Warning
Power cord is used as a disconnection device: To de-energize
equipment, disconnect the power cord. ! 8
Warning
Electrical-Type Class 1 Equipment: This equipment must be
earthed. The power plug must be connected to a properly wired earth
ground socket outlet. An improperly wired socket outlet could place
hazardous voltages on accessible metal parts. ! 9
Caution
Pluggable Equipment: The socket outlet should be installed near the
equipment and should be easily accessible. ! 10
Caution
Air vents: The air vents must not be blocked on the unit and must have
free access to the room ambient air for cooling. ! 11
Caution
Operating Temperature: This product is designed for a maximum
ambient temperature of 50°C. ! 12
Caution
All Countries: Install this product in accordance with local and
National Electric Codes. ! 13
3
Reviewing Connectivity Guidelines
The AT-B15/SX has one 1000BASE-SX fiber optic port with an SC connector.
This module operates at 1Gbps and supports auto-negotiation for duplex mode
(half- or full-duplex) and flow control. Refer to Table 2 for the cabling
specifications for this module.
Table 2 Cabling Specifications for the AT-B15/SX Expansion Module
Cable
Fiber Bandwidth
Minimum to Maximum
Cable Length
62.5/125 micron multimode fiber
160 MHz/km
2-220 m (7-722 ft)
200MHz/km
2-275 m (7-902 ft)
50/125 micron multimode fiber
400MHz/km
2-500 m (7-1641 ft)
500 MHz/km
2-550 m (7-1805 ft)
The AT-B15/LX has one 1000BASE-LX fiber optic port with an SC connector.
This module operates at 1Gbps and supports auto-negotiation for duplex mode
(half- or full-duplex) and flow control. Refer to Table 3 for the cabling
specifications for this module.
Table 3 Cabling Specifications for the AT-B15/LX Expansion Module
Cable
Fiber Bandwidth
Minimum to Maximum
Cable Length
62.5/125 micron multimode fiber
500 MHz/km
2-550 m (7-1805 ft)
50/125 micron multimode fiber
400MHz/km
2-550 m (7-1805 ft)
500 MHz/km
2-550 m (7-1805 ft)
9/125 micron singlemode fiber
N/A
2-5 km (7-16,404 ft)
The AT-B17 expansion module has two 100BASE-FX ports with SC
connectors. For cabling specifications for this module, refer to the AT-8324SX
Fast Ethernet Switch Installation Guide.
4
AT-B15 and AT-B17 Quick Install Guide
Handling the Module
Caution
The expansion module can easily be damaged by electrostatic discharge.
To prevent electrostatic damage, observe the following guidelines:
"
Wear an anti-static wristband connected to a suitable earth ground
whenever handling the module.
"
Do not remove the module from its packaging until you are ready to
install it.
"
Do not touch any of the module’s pins, connectors or components.
"
Hold the module only by its edges or front panel.
"
Store or transport this module only in appropriate anti-static
packaging.
Installing the Module
To install the expansion module, perform the following procedure:
1.
Power off the switch by disconnecting the AC power cord from the switch.
If a redundant power unit (RPU) is present, disconnect its DC cable
connection to the switch.
Caution
The switch must be powered off before installing or replacing any
module. Installing a module with the switch powered on can damage the
module.
2.
Using a flathead screwdriver, remove the faceplate from either the lower
right (slot A) or the lower left (slot B) expansion slot, as shown in Figure 4.
Allied Telesyn recommends installing the module in the lower right
expansion slot (slot A) and reserving the lower left slot for the optional
AT-STACK1 Stacking Module.
Caution
Do not install the expansion module in the upper expansion slot (slot
MGMT). This slot is reserved for the optional AT-BMGMT Management
Module.
5
Figure 4 Removing a Faceplate
Note
Keep the original faceplate for future use. If you should remove the
module, replace the faceplate to prevent dust and debris from entering
the unit and to maintain proper air flow.
Caution
Be sure to wear an anti-static wristband while performing the next step.
The AT-STACK1 module can be damaged by electrostatic discharge.
6
AT-B15 and AT-B17 Quick Install Guide
3.
Insert the new module into the switch. Holding the new module with the
text on the front panel upright, carefully slide the module into the switch
slot, ensuring that the edge connector is fully engaged. Once the new
module is installed, check to be sure the front panel of the module is flush
against the switch.
Figure 5 Installing the Expansion Module
4.
Using a flathead screwdriver, secure the new module to the switch by
tightening the attached screws.
5.
Connect the fiber optic cable(s) to the port(s) on the newly installed
module.
6.
Power on the switch by reconnecting the previously removed power sources
to the switch. The switch’s front-panel LEDs should indicate their status
of the new connection. Check the LED indicators for the fiber ports to
ensure that they are operating properly. Refer to the table of LEDs in this
guide for a description of the LED indications. If the module does not
respond, see "Troubleshooting" below.
More details concerning connection options and network applications can be
found in the AT-8324SX Fast Ethernet Switch Installation Guide, which is
available from the Allied Telesyn web site.
7
LEDs
The front panel of the switch has several LEDs that report the status of the
port(s) on the expansion module. Table 4 defines the LEDs.
Table 4 Expansion Module LEDs
LED
Condition
Status
STATUS
On
A module is installed in the slot.
ACT
Flashing
Traffic is passing through the port.
Troubleshooting
If you experience any problems with the module, check the following items
before contacting Allied Telesyn Technical Support:
"
Ensure the switch with the module is powered up.
"
Ensure that the device attached to the module is powered up and
operating correctly.
"
Ensure that the module is properly seated in the slot.
"
Verify that the module port is configured to match the communication
mode used by the attached device.
"
Check the connectors on both ends of the cable to be sure they are
properly engaged. When attaching fiber cable to an SC-type port, be
sure the plug clicks into place to ensure that it is properly seated.
"
If you are using fiber optic cable with an ST-type connector (in
conjunction with an SC-ST converter), try switching the TX and RX
connectors. Also, be sure the fiber terminators are clean. Dirty fiber
terminators on fiber optic cables will impair the quality of the light
transmitted through the cable.
Warranty Registration
When you are finished installing the module, register your product by
completing the enclosed warranty card and sending it in, or by visiting our
web site at www.alliedtelesyn.com/forms/warranty.htm and completing
the on-line registration form.
8
AT-B15 and AT-B17 Quick Install Guide
Technical Specifications
Table 5 lists the technical specifications for the expansion modules.
Table 5 Technical Specifications
Ports
AT-B15/SX
One 1000BASE-SX with SC connector
AT-B15/LX
One 1000BASE-LX with SC connector
AT-B17
Two 100BASE-FX with SC connectors
Cable Type
AT-B15/SX
50/125 or 62.5/125 micron multimode fiber
AT-B15/LX
50/125 or 62.5/125 micron multimode fiber
AT-B17
50/125 or 62.5/125 micron multimode or 9/125
micron single-mode fiber
Switching Method
Store-and-forward
Filtering/Forwarding
Full line speed
Queue Buffer
AT-B15/SX
2 Mbytes
AT-B15/LX
2 Mbytes
AT-B17
128K bytes per port
Power Consumption
AT-B15/SX
2.4W maximum
AT-B15/LX
2.4W maximum
AT-B17
10.6W maximum
Temperature
Operating: 32° to 122° F (0° to 50° C)
Storage: -4° to 158° F (-20° to 70° C)
Operating Humidity
5% to 95% (non-condensing)
9
Table 5 Technical Specifications
Compliances
CE Mark
EN55022 (CISPR22) Class A
VCCI Class A
C-Tick
Standards
AT-B15/SX
IEEE 802.3z, ISO/IEC 8802-3
AT-B15/LX
IEEE 802.3z, ISO/IEC 8802-3
AT-B17
IEEE 802.3, IEEE 802.3u, ISO/IEC 8802-3
Certification
Emissions
FCC Class A, VCCI Class A, CISPR Class A
Immunity
IEC 1000-4-2/3/4/6
CE Mark
10
Appendix A
Translated Safety and Emission Information
Important: This appendix contains multiple-language translations for the
safety statements in this guide.
Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch
enthaltenen Sicherheitshinweise in mehreren Sprachen.
Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af
sikkerhedsadvarslerne i denne håndbog.
Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de
veiligheidsopmerkingen in deze gids.
Important: Cette annexe contient la traduction en plusieurs langues des
instructions de sécurité figurant dans ce guide.
Tärkeää: Tämä liite sisältää tässä oppaassa esiintyvät turvaohjeet usealla
kielellä.
Importante: questa appendice contiene traduzioni in più lingue degli avvisi di
sicurezza di questa guida.
Viktig: Dette tillegget inneholder oversettelser til flere språk av
sikkerhetsinformasjonen i denne veiledningen.
Importante: Este anexo contém traduções em vários idiomas das advertências
de segurança neste guia.
Importante: Este apéndice contiene traducciones en múltiples idiomas de los
mensajes de seguridad incluidos en esta guía.
Obs! Denna bilaga innehåller flerspråkiga översättningar av
säkerhetsmeddelandena i denna handledning.
11
Standards: This product meets the following standards.
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
this instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or
the FCC, can void your right to operate this equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement
sur le matériel brouilleur du Canada.
!1
RFI Emission
!2
WARNING: In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
!3
Immunity
EN55022 Class A
EN60555-2 (1995) Class A
EN60555-3
IEC 1000-4-2 (4 kV CD, 8 kV AD)
IEC 1000-4-3 (1995) (3 V/m)
IEC 1000-4-4 (1995) (1.0 kV - (power line);
0.5 kV - (signal line))
IEC 1000-4-6 (1995) (3 Vrms)
EN50082-1 (1992)
EN61000-4-2 (1995)
EN61000-4-4 (1995)
SAFETY
!4
WARNING: Class 1 Laser product.
!5
WARNING: Do not stare into the laser beam.
!6
ELECTRICAL NOTICES
WARNING: ELECTRIC SHOCK HAZARD
To prevent ELECTRIC shock, do not remove the cover. No user-serviceable parts
inside. This unit contains HAZARDOUS VOLTAGES and should only be opened by a
trained and qualified technician. To avoid the possibility of ELECTRIC SHOCK,
disconnect electric power to the product before connecting or disconnecting the LAN
cables.
!7
LIGHTNING DANGER
DANGER: DO NOT WORK on equipment or CABLES during periods of
LIGHTNING ACTIVITY.
!8
CAUTION: POWER CORD IS USED AS A DISCONNECTION DEVICE. TO DEENERGIZE EQUIPMENT, disconnect the power cord.
12
AT-B15 and AT-B17 Quick Install Guide
!9
ELECTRICAL - TYPE CLASS 1 EQUIPMENT
THIS EQUIPMENT MUST BE EARTHED. Power plug must be connected to a
properly wired earth ground socket outlet. An improperly wired socket outlet could
place hazardous voltages on accessible metal parts.
! 10
PLUGGABLE EQUIPMENT, the socket outlet shall be installed near the equipment
and shall be easily accessible.
! 11
CAUTION: Air vents must not be blocked and must have free access to the room
ambient air for cooling.
! 12
OPERATING TEMPERATURE: This product is designed for a maximum ambient
temperature of 50° degrees C.
! 13
ALL COUNTRIES: Install product in accordance with local and National Electrical
Codes.
Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.
!1
Hochfrequenzstörung
!2
WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen
hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen
ergreifen.
!3
Störsicherheit
EN55022 Klasse A
EN60555-2 (1995) Klasse A
EN60555-3
IEC 1000-4-2 (4 kV CD, 8 kV AD)
IEC 1000-4-3 (1995) (3 V/m)
IEC 1000-4-4 (1995) (1.0 kV - (power line);
0.5 kV - (signal line))
IEC 1000-4-6 (1995) (3 Vrms)
EN50082-1 (1992)
EN61000-4-2 (1995)
EN61000-4-4 (1995)
SICHERHEIT
!4
WARNUNG Laserprodukt der Klasse 1.
!5
WARNUNG Nicht direkt in den Strahl blicken.
!6
ACHTUNG: GEFÄHRLICHE SPANNUNG
Das Gehäuse nicht öffnen. Das Gerät enthält keine vom Benutzer wartbaren Teile.
Das Gerät steht unter Hochspannung und darf nur von qualifiziertem technischem
Personal geöffnet werden. Vor Anschluß der LAN-Kabel, Gerät vom Netz trennen.
!7
GEFAHR DURCH BLITZSCHLAG
GEFAHR: Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters
ausführen.
!8
VORSICHT: DAS NETZKABEL DIENT ZUM TRENNEN DE
STROMVERSORGUNG. ZUR TRENNUNG VOM NETZ, KABEL AUS DE
STECKDOSE ZIEHEN.
!9
GERÄTE DER KLASSE 1
DIESE GERÄTE MÜSSEN GEERDET SEIN. Der Netzstecker darf nur mit einer
vorschriftsmäßig geerdeten Steckdose verbunden werden. Ein unvorschriftsmäßiger
Anschluß kann die Metallteile des Gehauses unter gefährliche elektrische
Spannungen setzen.
! 10
STECKBARES GERÄT: Die Anschlußbuchse sollte in der Nähe der Einrichtung
angebracht werden und leicht zugänglich sein."
13
! 11
VORSICHT
Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum Kühlen
freien Zugang zur Raumluft haben.
! 12
BETRIEBSTEMPERATUR: Dieses Produkt wurde für den Betrieb in einer
Umgebungstemperatur von nicht mehr als 50° C entworfen.
! 13
ALLE LÄNDER: Installation muß örtlichen und nationalen elektrischen
Vorschriften entsprechen.
Standarder: Dette produkt tilfredsstiller de følgende standarder.
!1
Radiofrekvens forstyrrelsesemission
!2
ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse.
Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige
foranstaltninger.
!3
Immunitet
EN55022 Klasse A
EN60555-2 (1995) Klasse A
EN60555-3
IEC 1000-4-2 (4 kV CD, 8 kV AD)
IEC 1000-4-3 (1995) (3 V/m)
IEC 1000-4-4 (1995) (1.0 kV - (power line);
0.5 kV - (signal line))
IEC 1000-4-6 (1995) (3 Vrms)
EN50082-1 (1992)
EN61000-4-2 (1995)
EN61000-4-4 (1995)
SIKKERHED
!4
ADVARSEL Laserprodukt av klasse 1.
!5
ADVARSEL Stirr ikke på strålen.
!6
ELEKTRISKE FORHOLDSREGLER
ADVARSEL: RISIKO FOR ELEKTRISK STØD
For at forebygge ELEKTRISK stød, undlad at åbne apparatet. Der er ingen indre
dele, der kan repareres af brugeren. Denne enhed indeholder LIVSFARLIGE
STRØMSPÆNDINGER og bør kun åbnes af en uddannet og kvalificeret tekniker.
For at undgå risiko for ELEKTRISK STØD, afbrydes den elektriske strøm til
produktet, før LAN-kablerne monteres eller afmonteres.
!7
FARE UNDER UVEJR
FARE: UNDLAD at arbejde på udstyr eller KABLER i perioder med
LYNAKTIVITET.
!8
ADVARSEL: DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE
STRØMMEN. SKAL STRØMMEN TIL APPARATET AFBRYDES, tages ledningen
ud af stikket.
!9
ELEKTRISK - KLASSE 1-UDSTYR
DETTE UDSTYR KRÆVER JORDFORBINDELSE. Stikket skal være forbundet
med en korrekt installeret jordforbunden stikkontakt. En ukorrekt installeret
stikkontakt kan sætte livsfarlig spænding til tilgængelige metaldele.
! 10
UDSTYR TIL STIKKONTAKT, stikkontakten bør installeres nær ved udstyret og
skal være lettilgængelig.
! 11
ADVARSEL: Ventilationsåbninger må ikke blokeres og skal have fri adgang til den
omgivende luft i rummet for afkøling.
! 12
BETJENINGSTEMPERATUR: Dette apparat er konstrueret til en omgivende
temperatur på maksimum 50 grader C.
14
AT-B15 and AT-B17 Quick Install Guide
! 13
ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal og
national lovgivning for elektriske installationer.
Eisen: Dit product voldoet aan de volgende eisen.
!1
RFI Emissie
!2
WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in welk
geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen.
!3
Immuniteit
EN55022 Klasse A
EN60555-2 (1995) Klasse A
EN60555-3
IEC 1000-4-2 (4 kV CD, 8 kV AD)
IEC 1000-4-3 (1995) (3 V/m)
IEC 1000-4-4 (1995) (1.0 kV - (power line);
0.5 kV - (signal line))
IEC 1000-4-6 (1995) (3 Vrms)
EN50082-1 (1992)
EN61000-4-2 (1995)
EN61000-4-4 (1995)
VEILIGHEID
!4
WAARSHUWING Klasse-1 laser produkt.
!5
WAARCHUWING Neit in de straal staren.
!6
WAARSCHUWINGEN MET BETREKKING TOT ELEKTRICITEIT
WAARSCHUWING: GEVAAR VOOR ELEKTRISCHE SCHOKKEN
Verwijder het deksel niet, teneinde ELEKTRISCHE schokken te voorkomen.
Binnenin bevinden zich geen onderdelen die door de gebruiker onderhouden kunnen
worden. Dit toestel staat onder GEVAARLIJKE SPANNING en mag alleen worden
geopend door een daartoe opgeleide en bevoegde technicus. Om het gevaar op
ELEKTRISCHE SCHOKKEN te vermijden, moet u het toestel van de stroombron
ontkoppelen alvorens de LAN-kabels te koppelen of ontkoppelen.
!7
GEVAAR VOOR BLIKSEMINSLAG
GEVAAR: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.
!8
WAARSCHUWING: HET TOESTEL WORDT UITGESCHAKELD DOOR DE
STROOMKABEL TE ONTKOPPELEN.OM HET TOESTEL STROOMLOOS TE
MAKEN: de stroomkabel ontkoppelen.
!9
ELEKTRISCHE TOESTELLEN VAN KLASSE 1
DIT TOESTEL MOET GEAARD WORDEN. De stekker moet aangesloten zijn op een
juist geaarde contactdoos. Een onjuist geaarde contactdoos kan de metalen
onderdelen waarmee de gebruiker eventueel in aanraking komt onder gevaarlijke
spanning stellen.
! 10
AAN TE SLUITEN APPARATUUR, de contactdoos wordt in de nabijheid van de
apparatuur geïnstalleerd en is gemakkelijk te bereiken."
! 11
OPGELET: De ventilatiegaten mogen niet worden gesperd en moeten de
omgevingslucht ongehinderd toelaten voor afkoeling.
! 12
BEDRIJFSTEMPERATUUR: De omgevingstemperatuur voor dit produkt mag
niet meer bedragen dan 50 graden Celsius.
! 13
ALLE LANDEN: het toestel installeren overeenkomstig de lokale en nationale
elektrische voorschriften.
15
Normes: ce produit est conforme aux normes de suivantes:
!1
Emission d’interférences radioélectriques EN55022 Classe A
EN60555-2 (1995) Classe A
EN60555-3
!2
MISE EN GARDE : dans un environnement domestique, ce produit peut provoquer
des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les
mesures adéquates.
!3
Immunité
IEC 1000-4-2 (4 kV CD, 8 kV AD)
IEC 1000-4-3 (1995) (3 V/m)
IEC 1000-4-4 (1995) (1.0 kV - (power line);
0.5 kV - (signal line))
IEC 1000-4-6 (1995) (3 Vrms)
EN50082-1 (1992)
EN61000-4-2 (1995)
EN61000-4-4 (1995)
SÉCURITÉ
!4
ATTENTION Producit laser di classe 1.
!5
ATTENTION Ne pas fixer le faisceau des yeux.
!6
INFORMATION SUR LES RISQUES ÉLECTRIQUES
AVERTISSEMENT: DANGER D’ÉLECTROCUTION
Pour éviter toute ÉLECTROCUTION, ne pas ôter le revêtement protecteur du
matériel. Ce matériel ne contient aucun élément réparable par l’utilisateur. Il
comprend des TENSIONS DANGEREUSES et ne doit être ouvert que par un
technicien dûment qualifié. Pour éviter tout risque d’ÉLECTROCUTION,
débrancher le matériel avant de connecter ou de déconnecter les câbles LAN.
!7
DANGER DE FOUDRE
DANGER: NE PAS MANIER le matériel ou les CÂBLES lors d’activité orageuse.
!8
ATTENTION: LE CORDON D’ALIMENTATION SERT DE MISE HORS CIRCUIT.
POUR COUPER L’ALIMENTATION DU MATÉRIEL, débrancher le cordon.
!9
ÉQUIPEMENT DE CLASSE 1 ÉLECTRIQUE
CE MATÉRIEL DOIT ÊTRE MIS A LA TERRE. La prise de courant doit être
branchée dans une prise femelle correctement mise à la terre car des tensions
dangereuses risqueraient d’atteindre les pièces métalliques accessibles à
l’utilisateur.
! 10
EQUIPEMENT POUR BRANCHEMENT ELECTRIQUE, la prise de sortie doit être
placée près de l’équipement et facilement accessible".
! 11
ATTENTION: Ne pas bloquer les fentes d’aération, ceci empêcherait l’air ambiant
de circuler librement pour le refroidissement.
! 12
TEMPÉRATURE DE FONCTIONNEMENT: Ce matériel est capable de tolérer
une température ambiante maximum de ou 50 degrés Celsius.
! 13
POUR TOUS PAYS: Installer le matériel conformément aux normes électriques
nationales et locales.
16
AT-B15 and AT-B17 Quick Install Guide
Standardit: Tämä tuote on seuraavien standardien mukainen.
!1
Radioaaltojen häirintä
!2
VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä
tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin
toimenpiteisiin.
!3
Kestävyys
EN55022 Luokka A
EN60555-2 (1995) Luokka A
EN60555-3
IEC 1000-4-2 (4 kV CD, 8 kV AD)
IEC 1000-4-3 (1995) (3 V/m)
IEC 1000-4-4 (1995) (1.0 kV - (power line);
0.5 kV - (signal line))
IEC 1000-4-6 (1995) (3 Vrms)
EN50082-1 (1992)
EN61000-4-2 (1995)
EN61000-4-4 (1995)
TURVALLISUUS
!4
VAROITUS Luokan 1 Lasertuote.
!5
VARIOTUS Älä katso säteeseen.
!6
SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA
VAROITUS: SÄHKÖISKUVAARA
Estääksesi SÄHKÖISKUN älä poista kantta. Sisällä ei ole käyttäjän huollettavissa
olevia osia. Tämä laite sisältää VAARALLISIA JÄNNITTEITÄ ja sen voi avata vain
koulutettu ja pätevä teknikko. Välttääksesi SÄHKÖISKUN mahdollisuuden
katkaise sähkövirta tuotteeseen ennen kuin liität tai irrotat paikallisverkon (LAN)
kaapelit.
!7
SALAMANISKUVAARA
HENGENVAARA: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA
SALAMOINNIN AIKANA.
!8
HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN VIRRANKATKAISULAITTEENA.
VIRTA KATKAISTAAN irrottamalla virtajohto.
!9
SÄHKÖ - TYYPPILUOKAN 1 LAITTEET
TÄMÄ LAITE TÄYTYY MAADOITTAA. Pistoke täytyy liittää kunnollisesti
maadoitettuun pistorasiaan. Virheellisesti johdotettu pistorasia voi altistaa
metalliosat vaarallisille jännitteille.
! 10
PISTORASIAAN KYTKETTÄVÄ LAITE; pistorasia on asennettava laitteen lähelle
ja siihen on oltava esteetön pääsy."
! 11
HUOMAUTUS: Ilmavaihtoreikiä ei pidä tukkia ja niillä täytyy olla vapaa yhteys
ympäröivään huoneilmaan, jotta ilmanvaihto tapahtuisi.
! 12
KÄYTTÖLÄMPÖTILA: Tämä tuote on suunniteltu ympäröivän ilman
maksimilämpötilalle 50°C.
! 13
KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten
sähköturvallisuusmääräysten mukaisesti.
17
Standard: Questo prodotto è conforme ai seguenti standard.
!1
Emissione RFI (interferenza di radiofrequenza) EN55022 Classe A
EN60555-2 (1995) Classe A
EN60555-3
!2
AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio
interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati
provvedimenti.
!3
Immunità
IEC 1000-4-2 (4 kV CD, 8 kV AD)
IEC 1000-4-3 (1995) (3 V/m)
IEC 1000-4-4 (1995) (1.0 kV - (power line);
0.5 kV - (signal line))
IEC 1000-4-6 (1995) (3 Vrms)
EN50082-1 (1992)
EN61000-4-2 (1995)
EN61000-4-4 (1995)
NORME DI SICUREZZA
!4
AVVERTENZA Prodotto laser di Classe 1.
!5
AVERTENZA Non fissare il raggio con gli occhi.
!6
AVVERTENZE ELETTRICHE
ATTENZIONE: PERICOLO DI SCOSSE ELETTRICHE
Per evitare SCOSSE ELETTRICHE non asportare il coperchio. Le componenti
interne non sono riparabili dall’utente. Questa unità ha TENSIONI PERICOLOSE e
va aperta solamente da un tecnico specializzato e qualificato. Per evitare ogni
possibilità di SCOSSE ELETTRICHE, interrompere l’alimentazione del dispositivo
prima di collegare o staccare i cavi LAN.
!7
PERICOLO DI FULMINI
PERICOLO: NON LAVORARE sul dispositivo o sui CAVI durante
PRECIPITAZIONI TEMPORALESCHE.
!8
ATTENZIONE: IL CAVO DI ALIMENTAZIONE È USATO COME DISPOSITIVO
DI DISATTIVAZIONE. PER TOGLIERE LA CORRENTE AL DISPOSITIVO
staccare il cavo di alimentazione.
!9
ELETTRICITÀ - DISPOSITIVI DI CLASSE 1
QUESTO DISPOSITIVO DEVE AVERE LA MESSA A TERRA. La spina deve essere
inserita in una presa di corrente specificamente dotata di messa a terra. Una presa
non cablata in maniera corretta rischia di scaricare una tensione pericolosa su parti
metalliche accessibili.
! 10
APPARECCHIATURA COLLEGABILE, la presa va installata vicino all’apparecchio
per risultare facilmente accessibile".
! 11
ATTENZIONE: le prese d’aria non vanno ostruite e devono consentire il libero
ricircolo dell’aria ambiente per il raffreddamento.
! 12
TEMPERATURA DI FUNZIONAMENTO: Questo prodotto è concepito per una
temperatura ambientale massima di 50 gradi centigradi.
! 13
TUTTI I PAESI: installare il prodotto in conformità delle vigenti normative
elettriche nazionali.
18
AT-B15 and AT-B17 Quick Install Guide
Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer.
!1
RFI stråling
!2
ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake
radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler.
!3
Immunitet
EN55022 Klasse A
EN60555-2 (1995) Klasse A
EN60555-3
IEC 1000-4-2 (4 kV CD, 8 kV AD)
IEC 1000-4-3 (1995) (3 V/m)
IEC 1000-4-4 (1995) (1.0 kV - (power line);
0.5 kV - (signal line))
IEC 1000-4-6 (1995) (3 Vrms)
EN50082-1 (1992)
EN61000-4-2 (1995)
EN61000-4-4 (1995)
SIKKERHET
!4
ADVARSEL Laserprodukt av klasse 1.
!5
ADVARSAL Stirr ikke på strålen.
!6
ELEKTRISITET
ADVARSEL: FARE FOR ELEKTRISK SJOKK
For å unngå ELEKTRISK sjokk, må dekslet ikke tas av. Det finnes ingen deler som
brukeren kan reparere på innsiden. Denne enheten inneholder FARLIGE
SPENNINGER, og må kun åpnes av en faglig kvalifisert tekniker. For å unngå
ELEKTRISK SJOKK må den elektriske strømmen til produktet være avslått før
LAN-kablene til- eller frakobles.
!7
FARE FOR LYNNEDSLAG
FARE: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.
!8
FORSIKTIG: STRØMLEDNINGEN BRUKES TIL Å FRAKOBLE UTSTYRET.
FOR Å DEAKTIVISERE UTSTYRET, må strømforsyningen kobles fra.
!9
ELEKTRISK - TYPE 1- KLASSE UTSTYR
DETTE UTSTYRET MÅ JORDES. Strømkontakten må være tilkoplet en korrekt
jordet kontakt. En kontakt som ikke er korrekt jordet kan føre til farlig spenninger i
lett t ilgjengelige metalldeler.
! 10
UTSTYR FOR STIKKONTAKT. Stikkontakten skal monteres i nærheten av utstyret
og skal være lett tilgjengelig."
! 11
FORSIKTIG: Lufteventilene må ikke blokkeres, og må ha fri tilgang til luft med
romtemperatur for avkjøling.
! 12
DRIFTSTEMPERATUR: Dette produktet er konstruert for bruk i maksimum
romtemperatur på 50 grader celsius.
! 13
ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale
elektriske koder.
19
Padrões: Este produto atende aos seguintes padrões.
!1
Emissão de interferência de radiofrequênciaEN55022 Classe A
EN60555-2 (1995) Classe A
EN60555-3
!2
AVISO: Num ambiente doméstico este produto pode causar interferência na
radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas
adequadas.
!3
Imunidade
IEC 1000-4-2 (4 kV CD, 8 kV AD)
IEC 1000-4-3 (1995) (3 V/m)
IEC 1000-4-4 (1995) (1.0 kV - (power line);
0.5 kV - (signal line))
IEC 1000-4-6 (1995) (3 Vrms)
EN50082-1 (1992)
EN61000-4-2 (1995)
EN61000-4-4 (1995)
SEGURANÇA
!4
AVISO Produto laser de classe 1
!5
AVISO Não olhe fixamente para o raio.
!6
AVISOS SOBRE CARACTERÍSTICAS ELÉTRICAS
ATENÇÃO: PERIGO DE CHOQUE ELÉTRICO
Para evitar CHOQUE ELÉTRICO, não retire a tampa. Não contém peças que
possam ser consertadas pelo usuário. Este aparelho contém VOLTAGENS
PERIGOSAS e só deve ser aberto por um técnico qualificado e treinado. Para evitar
a possibilidade de CHOQUE ELÉTRICO, desconecte o aparelho da fonte de energia
elétrica antes de conectar e desconectar os cabos da LAN.
!7
PERIGO DE CHOQUE CAUSADO POR RAIO
PERIGO: NÃO TRABALHE no equipamento ou nos CABOS durante períodos
suscetíveis a QUEDAS DE RAIO.
!8
CUIDADO: O CABO DE ALIMENTAÇÃO É UTILIZADO COMO UM
DISPOSITIVO DE DESCONEXÃO. PARA DESELETRIFICAR O EQUIPAMENTO,
desconecte o cabo de ALIMENTAÇÃO.
!9
ELÉTRICO - EQUIPAMENTOS DO TIPO CLASSE 1
DEVE SER FEITA LIGAÇÃO DE FIO TERRA PARA ESTE EQUIPAMENTO. O
plugue de alimentação deve ser conectado a uma tomada com adequada ligação de fio
terra. Tomadas sem adequada ligação de fio terra podem transmitir voltagens
perigosas a peças metálicas expostas.
! 10
EQUIPAMENTO DE LIGAÇÃO, a tomada eléctrica deve estar instalada perto do
equipamento e ser de fácil acesso."
! 11
CUIDADO: As aberturas de ventilação não devem ser bloqueadas e devem ter acesso
livre ao ar ambiente para arrefecimento adequado do aparelho.
! 12
TEMPERATURA DE FUNCIONAMENTO: Este produto foi projetado para uma
temperatura ambiente máxima de 50 graus centígrados.
! 13
TODOS OS PAÍSES: Instale o produto de acordo com as normas nacionais e locais
para instalações elétricas.
20
AT-B15 and AT-B17 Quick Install Guide
Estándares: Este producto cumple con los siguientes estándares.
!1
Emisión RFI
!2
ADVERTENCIA: en un entorno doméstico, este producto puede causar
radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas
que sean convenientes al respecto.
!3
Inmunidad
EN55022 Clase A
EN60555-2 (1995) Clase A
EN60555-3
IEC 1000-4-2 (4 kV CD, 8 kV AD)
IEC 1000-4-3 (1995) (3 V/m)
IEC 1000-4-4 (1995) (1.0 kV - (power line);
0.5 kV - (signal line))
IEC 1000-4-6 (1995) (3 Vrms)
EN50082-1 (1992)
EN61000-4-2 (1995)
EN61000-4-4 (1995)
SEGURIDAD
!4
¡ADVERTENCIA! Producto láser Clase 1.
!5
¡ADVERTENCIA! No mirat fijamente el haz.
!6
AVISOS ELECTRICOS
ADVERTENCIA: PELIGRO DE ELECTROCHOQUE
Para evitar un ELECTROCHOQUE, no quite la tapa. No hay ningún componente en
el interior al cual puede prestar servicio el usuario. Esta unidad contiene
VOLTAJES PELIGROSOS y sólo deberá abrirla un técnico entrenado y calificado.
Para evitar la posibilidad de ELECTROCHOQUE desconecte la corriente eléctrica
que llega al producto antes de conectar o desconectar los cables LAN.
!7
PELIGRO DE RAYOS
PELIGRO: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los
equipos o en LOS CABLES durante TORMENTAS ELECTRICAS.
!8
ATENCION: EL CABLE DE ALIMENTACION SE USA COMO UN DISPOSITIVO
DE DESCONEXION. PARA DESACTIVAR EL EQUIPO, desconecte el cable de
alimentación.
!9
ELECTRICO - EQUIPO DEL TIPO CLASE 1
ESTE EQUIPO TIENE QUE TENER CONEXION A TIERRA. El cable tiene que
conectarse a un enchufe a tierra debidamente instalado. Un enchufe que no está
correctamente instalado podría ocasionar tensiones peligrosas en las partes
metálicas que están expuestas.
! 10
EQUIPO CONECTABLE, el tomacorriente se debe instalar cerca del equipo, en un
lugar con acceso fácil".
! 11
ATENCION: Las aberturas para ventilación no deberán bloquearse y deberán tener
acceso libre al aire ambiental de la sala para su enfriamiento.
! 12
TEMPERATURA REQUERIDA PARA LA OPERACIÓN: Este producto está
diseñado para una temperatura ambiental máxima de 50 grados C.
! 13
PARA TODOS LOS PAÍSES: Monte el producto de acuerdo con los Códigos
Eléctricos locales y nacionales.
21
Standarder: Denna produkt uppfyller följande standarder.
!1
Radiostörning
!2
VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan
tvinga användaren till att vidtaga erforderliga åtgärder.
!3
Immunitet
EN55022 Klass A
EN60555-2 (1995) Klass A
EN60555-3
IEC 1000-4-2 (4 kV CD, 8 kV AD)
IEC 1000-4-3 (1995) (3 V/m)
IEC 1000-4-4 (1995) (1.0 kV - (power line);
0.5 kV - (signal line))
IEC 1000-4-6 (1995) (3 Vrms)
EN50082-1 (1992)
EN61000-4-2 (1995)
EN61000-4-4 (1995)
SÄKERHET
!4
VARNING! Laserprodukt av klass 1.
!5
VARNING! Laserstrålning när enheten är öppen.
!6
TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICITETSRISK:
RISK FÖR ELEKTRISK STÖTFör att undvika ELEKTRISK stöt, ta ej av locket.
Det finns inga delar inuti som behöver underhållas. Denna apparat är under
HÖGSPÄNNING och får endast öppnas av en utbildad kvalificerad tekniker. För att
undvika ELEKTRISK STÖT, koppla ifrån produktens strömanslutning innan LANkablarna ansluts eller kopplas ur.
!7
FARA FÖR BLIXTNEDSLAG
FARA: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER.
!8
VARNING: NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT KOPPLA
FRÅN STRÖMMEN, dra ur nätkabeln.
!9
ELEKTRISKT - TYP KLASS 1 UTRUSTNING
DENNA UTRUSTNING MÅSTE VARA JORDAD. Nätkabeln måste vara ansluten
till ett ordentligt jordat uttag. Ett felaktigt uttag kan göra att närliggande
metalldelar utsätts för högspänning. Apparaten skall anslutas till jordat uttag, när
den ansluts till ett nätverk.
! 10
UTRUSTNING MED PLUGG. Uttaget skall installeras i utrustningens närhet och
vara lättåtkomligt".
! 11
VARNING: Luftventilerna får ej blockeras och måste ha fri tillgång till omgivande
rumsluft för avsvalning.
! 12
DRIFTSTEMPERATUR: Denna produkt är konstruerad för rumstemperatur ej
överstigande 50 grader Celsius.
! 13
ALLA LÄNDER: Installera produkten i enlighet med lokala och statliga
bestämmelser för elektrisk utrustning.
22
Appendix B
Technical Support Fax Order
Name _________________________________________________________________
Company ______________________________________________________________
Address _______________________________________________________________
City______________________ State/Province_______________________________
Zip/Postal Code ________________ Country_______________________________
Phone ______________________________ Fax_______________________________
Incident Summary
Model number of Allied Telesyn product I am using _______________________
Firmware release number of Allied Telesyn product _______________________
Other network software products I am using (e.g., network managers)
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
Brief summary of problem ______________________________________________
______________________________________________________________________
______________________________________________________________________
Conditions (List the steps that led up to the problem.)______________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
Detailed description (Please use separate sheet)
Please also fax printouts of relevant files such as batch files and configuration
files. When completed, fax this sheet to the appropriate Allied Telesyn office.
Fax numbers can be found on page viii.
23
Appendix C
AT-B15 and AT-B17 Quick Install Guide
Feedback
Please tell us what additional information you would like to see
discussed in this guide. If there are topics you would like information
on that were not covered in this guide, please photocopy this page,
answer the questions and fax or mail this form back to Allied Telesyn.
The mailing address and fax number are at the bottom of the page.
Your comments are valuable when we plan future revisions of this
guide.
I found the following the most valuable ___________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
I would like the following more developed ________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
I would find this guide more useful if _____________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
Please fax or mail your feedback. Fax to 1-408-736-0100. Or mail to:
Allied Telesyn International, Corp.
c/o Technical Communications
960 Stewart Drive, Suite B
Sunnyvale, CA 94086 USA
PN 613-50113-00 Rev A
25
Download PDF