Dacor | PWD27 | Specifications | Dacor PWD27 Specifications

Dacor PWD27 Specifications
Installation Instructions
Warming Drawer
Part No. 102345 Rev. F
Models:
EWD24, EWD27, EWD30, EWD36,
IWD24, IWD27, IWD30, MWDV27,
MWDH27, MWDV30, MWDH30,
MRWD27, MRWD30, PWD27, PWD30
All specifications are subject to change without notice. Dacor ® assumes no liability for changes to specifications.
© 2007 Dacor, all rights reserved.
Table of Contents
Before You Begin............................................................... 1
Important Safety Instructions........................................... 1
General Safety Precautions.............................................. 2
Installation Specifications................................................. 3
Verifying the Package Contents........................................ 3
Installation Planning.......................................................... 3
Install a Support Platform in the Cabinet.......................... 6
Electrical Power Supply Requirements............................. 6
Installation Instructions..................................................... 7
Remove the Drawer ......................................................... 7
Installing the Chassis........................................................ 7
Re-installing the Drawer.................................................... 8
Verifying the Warming Drawer Operation......................... 8
Installation Checklist......................................................... 8
Before You Begin...
Important:
•
•
Installer: In the interest of safety and to minimize
problems, read these installation instructions
completely and carefully before you begin the
installation process. Leave these installation
instructions with the customer.
Customer: Keep these installation instructions for
future reference and the local electrical inspector’s use.
•
If you have questions or problems with installation,
contact your Dacor dealer or the Dacor Customer
Service Team.
Dacor Customer Service Team
Phone: Web site:
(800) 793-0093
www.Dacor.com
Important Safety Instructions
Important Information About
Safety Instructions
•
The Important Safety Instructions and warnings in
these instructions are not meant to cover all possible
problems and conditions that can occur. Use common
sense and caution when installing, maintaining or
operating this or any other appliance.
•
Always contact the Dacor Customer Service Team
about problems and conditions that you don’t
understand.
Safety Symbols and Labels
DANGER
Immediate hazards that WILL result in severe personal
injury or death.
warning
Hazards or unsafe practices that COULD result in severe
personal injury or death.
caution
Hazards or unsafe practices that COULD result in minor
personal injury or property damage.
1
Important Safety Instructions
General Safety Precautions
To reduce risk of fire, electric shock, serious injury or death when using your appliance, follow basic precautions, including
the following:
warning
warning
•
Read this manual completely before using this
appliance.
•
Use this appliance only for its intended use as
described in this manual. Use it only to warm food
and heat plates and utensils. It is not designed for
commercial, industrial or laboratory use.
•
Do not store or install this appliance outdoors,
unless otherwise noted in these instructions. Do
not use this product near water – for example, near
sinks, swimming pools or in a wet basement.
•
If you receive a damaged product, immediately
contact your dealer or builder. Do not install or
operate an appliance that has been damaged or
dropped.
•
Make sure that the appliance has been properly
installed and grounded by a qualified installer
according to the accompanying installation
instructions. Have the installer show you the
location of the electrical outlet so that you know
where to disconnect power to the appliance.
•
•
Before performing any type of service, make sure
that the power plug is disconnected from the
electrical outlet.
•
Keep the electrical cord away from heated surfaces.
•
DO NOT TOUCH ANY OF THE SURFACES INSIDE
OR OUTSIDE THE WARMING DRAWER DURING
OR IMMEDIATELY AFTER USE. After use, make
sure these surfaces have had sufficient time to cool
before touching them. Heating elements may be
hot, even though they are dark in color.
•
•
•
2
Do not repair or replace any part of the warming
drawer unless specifically recommended in the
literature accompanying it. All other service should
be done by a qualified technician.
To avoid the possibility of fire or burns, do not allow
clothing, potholders, towels or rags to come into
contact with any part of the warming drawer during
and immediately after use. Do not wear loose or
hanging apparel while using the appliance.
To reduce the risk of fire in the warming drawer, do
not overcook food. Do not leave it unattended with
paper, plastic or other combustible materials inside.
If materials inside the warming drawer should ignite,
keep the drawer closed and shut off the power at
the circuit breaker panel or fuse box.
•
Exercise caution when opening the warming drawer.
Let hot air or steam escape before looking or
reaching into the warming drawer.
•
Use only dry pot holders when removing food and
cookware from the warming drawer. Wet pot holders
can cause steam burns.
•
Do not put items like whole eggs, sealed containers
or closed glass jars in the drawer. They may
explode when heated, causing injury.
•
When the warming drawer is on in continuous
mode (∞), it will remain on until turned off manually.
Exercise caution when operating the unit in
continuous mode.
•
Do not place more than 50 pounds in the warming
drawer.
•
Properly clean and maintain the unit regularly as
instructed in the use and care manual. Clean only
those parts listed in this manual, in the manner
specified. DO NOT USE ABRASIVE CLEANERS
OR SCRUBBERS. THEY WILL PERMANENTLY
DAMAGE THE FINISH.
•
Do not use abrasive or caustic cleaners or
detergents on this appliance. They may permanently
damage the finishes. Do not use aerosol cleaners,
because they may be flammable or cause corrosion
of metal parts.
•
Clean the warming drawer thoroughly before
operating it for the first time.
•
Make sure the warming drawer is used only by
those individuals who are able to operate it properly.
•
Do not tamper with the controls.
•
Preheat the warming drawer before use.
•
Never allow anyone, including children to sit, stand
or climb on any part of the appliance, including
the drawer. Doing so may cause tipping, damage,
serious injury or death.
•
Do not leave children alone or unattended in the
area around the appliance. Do not allow children to
operate it, play with the controls, pull on the handle
or touch other parts.
•
Do not store items of interest to children above
the warming drawer. Children could be burned or
injured while climbing on the appliance.
Installation Specifications
Verifying the Package Contents
•
Use and Care manual
•
Mounting screws
C
B
Installation Planning
E
A qualified technician must complete the installation of this
built-in appliance. Proper installation is your responsibility.
Chassis
Carefully check the location where the drawer is to be
installed. The drawer should be placed for convenient
access. Make certain that electrical power can be provided
in the selected location.
5/16”
(8 mm)
Plan the installation so that all minimum clearances are
met or exceeded. Dimensions shown provide minimum
clearances, unless otherwise noted. Be certain that proper
clearance is provided for the drawer door when it is in the
open position.
Drawer open
F
The specified minimum cabinet depth and width must be
provided. The cabinet depth and width must completely
enclose the recessed portion of the drawer.
Cabinet cutout dimensions must be used as indicated. All
contact surfaces between the appliance and the cabinet
must be solid and level. The drawer support platform must
be flush with the bottom edge of the cabinet cutout.
Overall Dimensions - IWD Series
Top View
Make certain that you have everything necessary to ensure
a proper installation before proceeding.
Mounting hole,
9 places
40" (1016 mm)
3 prong
120 Vac power cord
G
D
Chassis without
drawer installed
A
Drawer Face Dimensions
(IWD Series Shown)
Warming
Drawer
Model No.
Dimension
“A”
Drawer Face
Width
Dimension
“B”
Chassis Width
Chassis Dimensions
(IWD Series Shown)
Dimension
“C”
Chassis Face
Width
IWD24
22 5/16” (567 mm) 22 1/4” (565 mm)
22 3/8” (568 mm)
IWD27
25 5/16” (643 mm) 25 1/4” (641 mm)
25 3/8” (645 mm)
IWD30
28 5/16” (719 mm) 28 1/4” (718 mm)
28 3/8” (721 mm)
Dimension Dimension Dimension Dimension
“D”
“E”
“F”
“G”
Drawer
Chassis
Drawer
Chassis
Face Height
Depth
Depth
Height
8 15/16”
(227 mm)
23 3/8”
(594 mm)
23 13/16”
(605 mm)
9 1/16”
(230 mm)
See following page for other models
3
Installation Specifications
Model
EWD24
10 1/8"
(257 mm)
“A” Drawer Face
Width
“B” Chassis Face
Width
“C” Chassis Width
24” (610 mm)
23 5/8” (600 mm)
22 1/4” (565 mm)
27” (686 mm)
26 5/8” (676mm)
25 1/4” (641 mm)
30” (762 mm)
29 5/8” (752 mm)
28 1/4” (718 mm)
EWD27
MWDH27
MWDV27
MRWD27
PWD27
A
EWD30
MWDH30
MWDV30
Drawer Face Dimensions
(MW Series Shown)
EWO
MRWD30
3 5/16"
(84mm)
PWD30
EWD36
1"
(25mm)
2 3/16"
(56mm)
PWO
EW
MWO
MW
3 1/4"
(83mm)
2 1/4"
(57mm)
35 5/8” (905mm)
1"
(25mm)
1"
(25mm)
34 1/4” (870 mm)
1 5/32"
(29mm)
1 1/8"
(29mm)
Warming Drawer Overall Dimensions
EWD
MWDH/V
MRWD
1"
(25mm)
PWD
2 1/4"
(57 mm)
3 1/4"
(83 mm)
1"
(25mm)
C
PW
3 7/16"
(87mm)
36” (914 mm)
1"
(25mm)
3 7/16"
(87 mm)
B
1 5/16"
(33mm)
1"
(25mm)
1"
(25mm)
Handle Dimensions
Chassis
23 3/8"
(594 mm)
Mounting
Hole 9 Places
1/2"
(13 mm)
5/64"
(2mm)
Drawer open
23 13/16
(605 mm)
10"
(254 mm)
Chassis without
drawer inserted
1/2"
(13 mm)
Overall Dimensions
Top View
(EWD Series Shown)
4
Chassis Dimensions
40" (1016 mm)
3 prong
120 Vac power cord
9"
(229 mm)
Installation Specifications
Warming Drawer
36" Typ.
(914 mm)
Warming Drawer
3/4" Min.*
(19 mm)
C
D
120 Vac
electrical
receptacle
C
3/4" Min.*
(19 mm)
A
B
Cooktop
27"/30"/36"
Dacor
single oven
D
Warming Drawer 120 Vac
Elect.
D
1 1/2" (38 mm)
Typical counter top
Warming Drawer
C
3/4” Min.*
(19 mm)
Warming Drawer 120 Vac
Elect.
Toe Kick
A
36" Typ.
(914 mm)
A
B
Model
IWD24
EWD24
“A” Cutout
Width
“B” Min.
Width to
Adjacent
Doors/
Drawers
22 1/2”
(572 mm)
24 1/4”*
(616 mm)
25 1/2”
(648 mm)
27 1/4”*
(692 mm)
C
C
3/4" Min.*
(19 mm)
120 Vac
electrical
receptacle
“C” Cutout
Height
“D” Min.
Vertical Gap
Between
Cutouts
9 1/8”
(232 mm)
1 1/4”*
(32 mm)
EWD27
IWD27
MWDH27
MWDV27
MRWD27
PWD27
EWD30
IWD30
MWDH30
MWDV30
28 1/2”
(724 mm)
30 1/4”*
(768 mm)
34 1/2”
(876 mm)
36 1/4”
(921 mm)
MRWD30
PWD30
EWD36
* Bare minimum spacing shown to allow for ventilation and avoid scrapping. On
IWD series models, additional space may be required if an oversized drawer front
is used. Use the drawer face dimensions for the corresponding EWD series model
on page 4 for reference.
Cutouts Dimensions
Cutout Depth: 24” Min. (610 mm)
5
Installation Specifications
Install a Support Platform in the
Cabinet
Electrical Power Supply
Requirements
Provide a platform (100 lb. load capacity) within the cabinet
upon which the warming drawer will be supported. The
platform must be installed level and straight. The top edge
of the platform must be flush with the cutout at the front of
the cabinet. There are no provisions to level the warming
drawer after it has been installed. 3/4” (19 mm) thick
plywood is recommended.
•
The warming drawer is supplied with a power cord
terminated by a three-prong plug. Plug it directly into a
dedicated, grounded, three prong, electrical outlet. Do
not use an extension cord.
Three-Prong Plug
Three-Prong
Grounded Outlet
NOTE:
If the drawer is not installed in a level fashion, the
drawer may slide open on its own or may not seal
tightly, allowing heat to escape and resulting in poor
warming drawer performance.
Chassis
face
Support
platform
•
The correct voltage, frequency and amperage must be
supplied to the electrical outlet from a grounded, single
phase circuit that is protected by a properly sized circuit
breaker or time-delay fuse.
•
The required voltage, frequency and amperage ratings
are listed on the appliance data plate. The data plate
is located inside the chassis drawer opening on the left
side. Remove the drawer to expose it.
Nominal Electrical Supply Requirements
120 Vac, 60 Hz, 15 Amp. dedicated circuit
The warming drawer is supplied with a 40” (1016 mm)
power cord with a three prong grounded plug.
Total Connected Load
6
0.5 kW (4 Amp.)
•
If the power supply requirements shown above do not
agree with those listed on the product data plate, use
the requirements on the product data plate.
•
It is the owner’s responsibility to ensure that the
electrical outlet is installed by a qualified electrician.
The electrical installation must comply with the latest
revision of the National Electric Code ANSI/NFPA 70
and local codes and ordinances.
•
If the electrical service provided does not meet the
product specification, or does not conform to the NEC
or local standards, do not proceed with the installation.
Call a licensed electrician to correct the electrical
service before proceeding.
•
Be certain to locate the electrical outlet in an
accessible location, so that the warming drawer may
be easily unplugged in the event that service becomes
necessary.
Installation Instructions
warning
•
o avoid personal injury caused by the appliance
T
falling forward when the drawer is opened, secure
the chassis to the cabinet and support platform as
instructed.
•
Be certain that the power plug is disconnected from
the electrical outlet before installation.
•
Verify that the electrical supply matches the ratings
found on the appliance data plate and the installation
specifications before proceeding.
Remove the Drawer
emove the drawer from the appliance to allow access
R
to the mounting holes during installation, and to
reduce weight:
1. Pull the drawer out to the fully open position.
2. Push in on the locking tab on one side as you pull the
drawer up.
3. When the drawer comes loose from the slide, repeat
the same process on the opposite side.
Installing the Chassis
1. Grasp the warming drawer chassis on opposite
sides and slide it partially into the cabinet opening.
Temporarily support the chassis in place so that it will
not tilt or fall.
2. From an adjoining cabinet, reach in behind the drawer
and pull the power cord until the plug is next to the
electrical outlet. Do not plug in the power cord at this
time.
3. After positioning the power cord and plug, slide the
chassis completely into the cabinet until the front frame
is positioned flush against the cabinet face.
4. Use the screws provided to secure the warming drawer
chassis to the cabinet and support platform, insert them
into the mounting holes and tighten into place. You may
want to drill pilot holes prior to installing the mounting
screws.
Mounting Hole,
9 Places
4. Grip the drawer on both sides and pull it free.
5. For safety, push both drawer slides into the drawer
opening.
STEP 2: Push
locking tab
Continued...
STEP 3: Pull up on
front of drawer
7
Installation Instructions
Re-installing the Drawer
1. Pull the drawer slides all the way out of the drawer
opening.
2. Gently lower the drawer between the extended slides
until it is suspended by them.
3. Slide the back of the drawer mounting brackets under
the drawer mounting clips on the slides.
4. Push one side of the drawer down onto its locking tab,
until the tab locks into place.
5. Repeat the same process on the opposite side.
6. Gently open and close the drawer to make sure that it
is properly installed.
STEP 3: Slide mounting
bracket under clip on slide
Clip on slide
Slide
STEP 4: Push front of
drawer down until tabs lock
into place
8
Verifying the Warming Drawer
Operation
1. Connect power plug to the electrical outlet.
2. Operate the warming drawer as outlined in the use and
care manual that accompanied this product.
Installation Checklist
warning
•
To ensure a safe and proper installation, the
following checklist should be completed by the
installer to ensure that no part of the installation has
been overlooked.
•
Proper installation is the responsibility of the
homeowner. The importance of proper installation of
your warming drawer cannot be overemphasized.
□□
Has the mounting platform been installed according to
the instructions on page 6?
□□
Has the a properly grounded, dedicated, three prong
electrical outlet been installed for the appliance by a
licensed electrician? See page 6.
□□
Has the chassis been properly fastened to the
mounting platform and sides of the cabinet?
See page 7.
□□
□□
□□
Has the drawer been properly installed?
Has proper operation been verified?
Have any problems been noted on the warranty card
or during the on-line warranty activation? Has the
warranty been activated on-line or the warranty card
filled out completely and mailed?
Dacor ● 1440 Bridge Gate Drive, Diamond Bar, CA 91765 ● Tel: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising