Estate | E-S 1602 | Instruction manual | Estate E-S 1602 Instruction manual

Estate E-S 1602 Instruction manual
Instruction Manual for the
E-SCAR 1602 Heavy Duty
Carriage Door Opener
WARNING - Read all instructions before beginning installation or use of this door
opener. This operator exerts a high level of force. Exercise caution at all times and
stay clear of the system during operation.
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Estate Swing Summary of Functions
The Estate Swing is only to be used for vehicular swing doors in a Class I
setting.
Class I: A vehicular door opener (or system) intended for use in a home of
one-to-four single family dwelling, or a garage or parking area associated therewith.
The Estate Swing automated system was designed and built for controlling vehicle
access. Do not use for any other purpose.
The internal/external automation with articulated arms automates residential swing
-leaf carriage doors with leaves of up to 8’ in length. It consists of an irreversible
electro-mechanical operator with guard and an articulated-arm activation system to
be fitted to the door with the appropriate accessories. The irreversible system ensures the door is mechanical locked when the motor is not operating. A manual
release makes it possible to move the door in the event of a power-cut or fault.
Keep this manual safely stored after
installation.
Serial Number__________________________
Date of Purchase_______________________
Place of Purchase______________________
Have this information on hand while handling all
service and warranty issues.
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
MODEL
Power Supply
Rated Absorbed Power (Amperage pull on
a 120V AC outlet)
Specifications
Max Torque (Nm)
Use frequency (cycles/hour)
Operating ambient temperature
Gearmotor weight (lbs)
Protection class
Door leaf max length (ft.)
Door leaf max weight (lbs.)
Operator overall dimensions LxHxD(in.)
1)
2)
3)
4)
5)
6)
Estate Swing E-SCAR 1600
24VAC 50VA transformer (120VA max)
5 Amp/
200
> 100
-4 to 131 Deg F
35
IP44
Up to 8
Up to 800
12 5/8” x 6 7/8” x 6 3/8”
Motor
Manual Release Clutch Cam
Limit Switch Cams
Gear Box
Limit Switches
Transmission Shaft
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
1
Estate Swing Parts List
Motor Box Contents
1. Motor Mount Bolts (4)
2. Motor Mount Washers (4)
3. Motor Mount Spring Washers (4)
4. Motor Mount Lock Nut (4)
5. Cover Bolts (2)
6. Cover Blot O-Rings (2)
7. Motor Wire Gasket (1)
8. Manual Clutch Assembly (1)
9. Clutch Keys (2)
10. Cover Bolt Plugs (2)
3/8 Concrete anchors for column (4)
Motor Arm Contents
1. Pivot Bolts (2)
2. Nylon Pivot Bushings (6)
3. Lock Nuts (2)
5/16” hex bolts for door (cut to size) (2)
Control / Power Contents
1.
2.
3.
4.
5.
Control Board
Receiver
Transmitter
Transformer
Control Box
2
1
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
5
3
4
2
Tools Needed





Power Drill and appropriately sized bits.
Crescent Wrench
Flat Head Screwdriver
Nuts, Bolts, Anchors
and Washers (see below)
C-Ring Pliers






Phillips Head Screwdriver
Tape Measure
Level
Wire Strippers
C-clamps
Carpenters Clamps
Other items that may be needed prior to commencing installation.

16, 14 or 12 gauge, 2 conductor stranded low voltage wire will be required to run
power to your operator. Length is deter mined by distance between tr ansfor mer power supply and the control box.

A voltage meter and digital camera may be necessary to run diagnostic checks.

4 - 3/8” fasteners may be needed to connect the Base Plate to the wall.
Length and style will be determined by what is needed for a secure anchor for your material door. The kit includes concrete anchors for block construction garages.

2 - 5/16” fasteners may be needed to connect the Door Mounting Bracket to the door.
Length and style will be determined by what is needed for a secure anchor for your material door. The kit includes hex bolts designed to be inserted through your door. Other
methods can be used alternatively.

Hardware to attach the control box to a wall.
3
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Emergency & Operational Manual Operation Mode
In emergencies pull down on the red release rope until you hear two clicks and
this will release the door.
Test periodically for correct placement and function.
For left-hand side:
Pull the rope to the right clockwise to release
For right-hand side:
Pull the rope to the left counter-clockwise to release
Restoring Standard Operation
Disconnect power prior to re-engaging the manual release. If the board is active injury
from unexpected motor movement can occur.
To restore operation push up on the release lever until the rope is at the top as pictured above.
4
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
IMPORTANT: Determining Correct Position
This operator is intended to be on the inside of the garage and push
the carriage doors out towards the driveway.
The mounting plate can be positioned on the side of the frame using four of the six mounting
holes or above the frame. In both mounting options the drive shaft should further inside the door
frame than the door hinge. The drive shaft should always face down.
Distance from hinge of door to
inside mounting surface for the
opener =
Do not exceed 12”
Distance from hinge of door to
horizontal placement of
driveshaft inside door frame =
Do not exceed 6”
5
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Installation of Operator
The operator base plate and articulated arm are designed either for right-handed or
left-handed installation. There is no pre-determined designation.
1. Utilizing the center of the drive shaft hole in the base plate, find your correct setback from
the previous page.
2. Secure the base plate to the column using screws and a proper anchoring system for your
type of wall material. If using the provided block wall anchors drill holes using a 5/8”
concrete bit and a hammer drill. For added strength we suggest filling the hole with epoxy
prior to hammering in the anchor.
3. Place the operator motor onto the base plate and secure it with the 4 long bolts.
Important: The transmission shaft must always face downward.
6
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
4. Assemble the articulated arm and front coupling as shown below. Do not over tighten the lock nuts, the arms
should be able to pivot without resistance.
Left Hand Assembly
Right Hand Assembly
5. Attach the straight arm on the motor drive shaft spline and secure it in place
6. Manually release the operator and swing the arm assembly so the door bracket
is on the door in the open position. The arm should be almost straight with a
slight bend in the elbow of the arm assembly.
7. Ensure the arm is level and attach the door bracket using the 5/16 bolts. Once the bolts are attached the remainder can be cut off.
8. Relock the operator and assemble the motor housing.
7
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
For Your Convenience
The green terminal strips on the control board are easily removed for wiring. Simply pull straight out on
the terminal strip to remove it from the board. It will slide right off. Slide it back on when you are finished with your wiring connections.
Be sure you are placing your wires in the terminal
block correctly.
Take the terminal block off of the control board to insert
wires. Hold with screw terminals facing upward.
Turn the screw counter-clockwise to open the terminal and
clockwise to close the terminal.
The terminals come closed. Be sure not to mistake this for
open and insert the wires below the terminal clamp. This
will lack the conductivity to complete the circuit.
8
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Setting Limit Switches
1. Loosen the screw that holds the limit switch rings in place.
2. Move the door into the full open position. Move the top ring until it is pushing the switch on the
top limit switch in.
3. Move the door to the closed position. Move the bottom ring until it is pushing the switch on the
bottom limit switch.
4. Retighten the limit switch ring screw to hold the rings in the correct place on the driveshaft.
9
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Temporary Safety Jumpers
For the highest level of safety, the Estate Swing systems are set up with Normally Closed safety
terminals. This means that in order for the door opener to move these terminals must be closed
either through a safety device (recommended) or with jumpers. Temporary safety jumpers are
provided in the control box hardware bag for jumping terminals PHOTO and GND together
It is recommended not to use any accessories until setup and programming are complete.
NOTE: If not using safety devices the temporary safety jumper must remain in for the door
operator to move.
To the left is our recommended
safety set up. It consists of safety
edges mounted on the door on the
outside to react rapidly to impact
and photo beams at the base of the
door to halt movement of the doors
with obstruction.
10
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Wiring the Operator Motors
LEFT OPERATOR OPENS FIRST:
Motor1 L1-1: 16 AWG Red
Motor1 L1-2: 16 AWG Black
Motor2 L2-1: 16 AWG Black
Motor2 L2-2: 16 AWG Red
Limit1 OL1: Yellow
Limit1 COM1: Red
Limit1 CL1: Black
Limit2 OL2: Yellow
Limit2 COM2: Red
Limit2 CL2: Black
If you require the Right mounted door to open first change wires to:
Right hand motor: Motor 1 L1-1: Black, Motor1 L1-2: Red, Limits on Limit1 block
Left hand motor: Motor 2 L2-1: Red, Motor2 L2-2: Black, Limits on Limit2 block
11
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Estate Swing 433 Plug-in Receiver
1. With the red plug already inside the control box, run the grey
receiver wire out of the box through one of the water tight
connections.
2. Find a location for the receiver box on the door post or a fence
post that is within the length of the receiver wire.
3. Using a #6 screw attached the top of the receiver to the post.
If you are happy with this position use the small provided set
screw in the bottom hole to secure the receiver in place.
4. Attach the receiver wire to the terminals as seen below. Please
note that you will find a factory installed jumper wire connected on the receiver. Leave this jumper wire in place. One
of the terminals that has the jumper wire will have the White
wire added to the terminal.
12
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Estate Swing 433 Plug-in Receiver (cont.)
5. Plug the red clip inside the control box into the
control board. The groove in the red clips should snap
into the guide on the 5 prong connector. (Fig 1)
6. The red power light should come on the receiver.
(Fig 2)
7. Program your remotes to the receiver:
A. Press and release the LEARN1 button at the top of Fig. 1
the receiver board (ex 1). The learn LED will illuminate steady (ex 2). (Fig 3)
B. Press and hold the button on the remote you wish
to program to the receiver.
C. Hold the remote button until the Learn LED flashes and then turns off. (caution your door opener may
be triggered during this process)
D. Repeat A through C for all additional remotes.
Fig. 2
NOTES ABOUT REMOTES:
You can program up to 400 codes into the receiver. This
could mean 1 button on 400 different remotes or this could
mean all 4 buttons on 100 remotes or anything in between.
Some choose to program all 4 buttons to a single receiver if
they are not using multiple doors to eliminate pressing the
incorrect button on the remote. To do so follow the programming above with each button of the remote. You can
erase all programmed codes by holding Learn 1 until the
Learn LED comes ON and then turns OFF.
8. Put the cover on the receiver and secure it in place using
the provided screw.
Fig. 3
IMPORTANT: The r eceiver is a dr ip pr oof r eceiver . This means that it is designed to
prevent water from accessing the inside of the receiver when the water is moving downward
with gravity (rain for example).
DO NOT mount the r eceiver anyplace that water may access it fr om another angle.
For example: Do not mount near sprinklers. Do not mount the receiver horizontally. Do not
mount the receiver near a flat surface where water could splash upwards.
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
13
Power
Kit includes 1) 24V transformer. The transformer supplied has 2 screw terminals to connect to. You may locate
the transformer up to 200’ away from the control board using 16 gauge, 2 conductor stranded direct burial low
voltage wire. Do not use solid core wire.
Allow a minimum of 4’ of wire between the transformer and the control board.
Using the provided wire nuts, connect the wire (not provided) from the transformer to the two yellow
wires on the control board marked TRAN. There is no polarity.
Never run 110VAC power directly to the Estate Swing.
This will destroy the Estate Swing control board. Never connect the
power wire with the transformer plugged in. Contact between the
two lead wires, even for a second, will destroy the transformer.
Transformers are only warranted if the internal fuse is not blown. If
the fuse is blown an outside factor (shorting, surge, water, etc) has
caused the transformer not to function.
Plug the transformer into a 110 V AC outlet.
The transformer is not weather proof and must be kept inside the garage and out of weather.
Two 12V DC batteries (Max 5 a/h per battery) may be run in series as backup to the 24V transformer power.
Running two 12V batteries in series creates a 24V system, you cannot run them in parallel (see diagram above)
14
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Setting Operating Parameters
Important Dip Switch Setting
Verify the 3 dipswitches are as follows:
1. DOWN
2. UP
3. DOWN
First Run
This is our recommended procedure to run the doors for the first time.
PUSH 1 or PUSH 2 to increase or decrease the parameter. Then press SET button to
move to the next parameter.
1. Press SET button to begin.
2. LED shows P1: Press Push 1 to get P1 setting to 30.
3. Press SET button.
4. LED shows P2: Press Push 1 to get P2 setting to 10.
5. Press SET button.
6. LED shows P3: Press Push 1 to get P3 setting to 30.
7. Press SET button.
8. LED shows P4: Press Push 1 to get P4 setting to 3.
9. Press SET button.
10. LED shows P5: Press Push 1 to get P5 setting to 2.
11. Press SET button.
12. LED shows P6: Press Push 1 to get P6 setting to 10.
13. Press SET to finish. You should hear 3 beeps; this indicates parameter programming
is finished.
Manually unlock the doors, then move them half-way and re-engage. Activate using
Push 1 button (as shown above) The doors should run open. Press Push 1 again and
the doors should run closed. The doors are now set up for regular usage.
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
5.1
Operating Parameters Customization
1. LED shows P1: P1 is for setting your run time. The run time will be determined from the
time you had determined during the set up of the limit switches. Take that determined run time
and add 1 second. So if it takes 10 seconds to get from closed to open between limit switches;
set the run time to 11 seconds. The options are 0-99 seconds.
2. LED shows P2: P2 is for setting your slow down time. The door opener will slow down to
half speed after the time set on P2 expires. If you wish to have the doors open and close faster
make the slow down start time a longer period of time. If you want to put less stress on the
gears and door set the slow time shorter to slow the momentum sooner. The options will adjust
to match the previously set run time. NOTE: motor must be in slow down to detect limits—be
sure this number does not exceed the time the motor take to move from one limit to the other.
3. LED shows P3: P3 is the force setting, the lower the number the easier the doors will reverse
directions when it meets resistance. This number may have to be changed to a higher setting if
your doors are obstructing unexpectedly. The number should be set to the highest number
during initial setup and reduced to the point of reliable operation that takes into account change
in door resistance throughout the year. The options are 0-32.
4. LED shows P4: P4 is for setting a delay between leafs if you have overlapping doors or a
door lock. The motor wired into the master terminals (1) opens first if there is a delay and closes second. It is recommended to have a delay of 3 seconds to avoid any jamming issues between leafs.
5. LED shows P5: P5 is the release for the door lock – this option determines the length of time
24VDC will be sent out of terminals E_LOCK. The options are 1-4 seconds.
6. LED shows P6: P6 is the delay for automatic re-close from the open position – this option
needs to be turned on using the dip switch on the board. The options are 0-99 seconds.
15
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Troubleshooting
If the door opener will not move but the board is counting the run time:
• Check wiring connections.
• Be sure the arms are locked and not in manual operation.
• If not using slave limit switches, be sure jumpers are in place.
• Check the left hand fuse near the power supply—the proper way to inspect a fuse is to remove it from its clips
and check for continuity.
If the door opener moves a few inches or feet and stops or reverses directions:
• Increase the force setting (P3).
• Check the setback. The setback of the operator is important to correct operation due to leverage the arm will
have on the door.
• Check the battery voltage. Proper voltage should be between 13.4 – 13.8 and drop no more than a quarter of a
volt under load.
• Disconnect accessories that may be triggering the door a second time. The most frequent issues are from exit
sensors or other automatic opening devices.
The door does not reach the desired stop points:
• Adjust the limit switches.
• Lengthen the run time parameter (P1).
• Check setback— if setback is incorrect it will limit how far the door will move.
If the door will open but will not close:
• Manually move the door slightly off the open position and then trigger the door to go closed. If the door then
moves closed the limits are most likely wired backwards. (Meaning the open limit is wired to closed and closed
wired to open)
• If you are not using safety devices the safety jumpers are in place. If PH is on display it is an issue with the safety jumper or a device in the safety terminals.
• If you are using a safety device:
- Check to make sure you are using the normally closed connection instead of the normally open.
- Check to be sure there is continuity being provided between the common and normally closed wire of the safety
device. If there is not continuity then refer to the installation guide of the device to set up properly.
The display of the board will not light up:
• Check the power supply for 24VAC.
The arms are not wired in or properly wired on the limit switch connections. Without the limit switch connections
being closed the board will not light up.
More on next page
16
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Troubleshooting
The door opener is not stopping on the limit switches:
• Remove all pre-installed jumpers from the limit switch terminals that have limits going to them. The slave
door terminals come pre-jumped for single operation, if you are using a dual system pay particular attention
to this detail and remove the jumpers when you put your limit switches in.
• The limits are wired incorrectly—be sure that you are following the correct wiring diagram for pull to open
or push to open.
• For dual doors check that the delay between leafs is 2 or above. If both limits are triggered simultaneously
there is a chance a limit could be missed.
One or both arms are not moving:
• Check to be sure wiring color pattern matches the installation (Example: push to open wiring for a push to
open installation) - If the limits or motor are wiring opposite the installation the board will believe it is
closed or open when it is actually the opposite and the arms will never move.
• Check the limit wires are correctly in the terminal blocks. The terminal blocks come with the terminal
clamps closed - however when the terminal clamps are closed there is a small space below them one could
mistake as place to insert a wire. If this is done then conductivity of the connection will never be reached.
• Push or pull on the door - if it moves the gears are disengaged and the door is in manual release mode.
General fix for user to understand operation:
- Unlock the door opener arm and move it to the half way position. Change the run time to a low number
(example: 2). Run the operator repeatedly.
- The operator should run one direction for a 2 count and then the other for a 2 count. After you feel you
have it following the run time correctly and swinging level and easily, then start incrementally lengthening
the run time.
- Eventually the run time will allow the operator arm to reach both limit switches and your setup is complete.
Dual door - Only one arm moves:
• Check your dual settings - if the dip switch is changed to dual with the power on the setting will not take
effect, turn the power off and then back on to have the dual dip switch take effect. NOTE: If one leaf of a
dual door ever reaches its end limit before the other leaf starts moving, the leaf that hasn’t started moving
will not begin: correct this by cycling the doors again and let it travel the full stroke or decrease the delay
between leafs. The options are 0-9 seconds delay.
17
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Troubleshooting
If you call in for technical support or warranty
support: Before any control boar d or motor will be
permitted to be sent in for testing or warranty you will be
required to e-mail digital photos to the technician.
This is done in your best interest to save unnecessary shipping expenses and time lost.
Many times we can come up with solutions to issues by seeing pictures that relay information that is impossible to relay through a phone conversation.
Below are examples of control board pictures and motor pictures that we will be looking
for:
Picture shown is actual customer photo
18
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Control Board Overview
CAUTION! Do not r un 110V AC power direct to the boar d.
This will cause permanent damage to both boards and void your
warranty. Caution!
Door Opener reactions to signals:
PUSH1 and Receiver (PUSH 1 terminal, PUSH 1 button, 5 Prong Receiver):
Details:
• Will activate door with momentary contact (momentary contact between PUSH1 and V+) or if you momentarily
press the PUSH1 button.
• Controls both leaves in 2 leaf mode (Dip switch 2 in the ON position).
• Acts as party mode control to suspend auto-reclose by activating while counting down auto-reclose in the open
position.
Operational Sequence for terminal with auto-close ON (Dip switch 1 in on position):
1. In closed position - momentary contact will open doors.
2. When opening - momentary contact will stop doors and then it will auto reclose.
3. When stopped mid cycle waiting auto reclose - momentary contact will move the
door in the direction opposite what it was moving before stopped.
4. When open and counting auto-reclose pause time - momentary contact will stop
pause time.
5. Stopped in open position from override of auto-reclose from PUSH1 or Receiver momentary contact will reactivate pause time and close door.
6. When closing - momentary contact will stop the door and then it will auto reclose.
Operational Sequence for terminal with auto-close OFF (Dip switch 1 in off position):
1. In closed position - momentary contact will open doors.
2. When opening - momentary contact will stop doors.
3. When stopped mid cycle - momentary contact will move the door in the direction
opposite what it was moving before stopped.
4. When open - momentary contact will close doors.
5. When closing - momentary contact will stop the door.
6. When stopped mid cycle - momentary contact will open the door.
7. When open with auto-reclose off - momentary contact will have no effect.
8. When closing - momentary contact will re-open the door.
19
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Control Board Overview
CAUTION! Do not r un 110V AC power direct to the boar d.
This will cause permanent damage to both boards and void your
warranty. Caution!
Door Opener reactions to signals:
PUSH2 (PUSH 2 terminal and PUSH 2 button):
Details:
• Will activate door with momentary contact (momentary contact between PUSH2
and V+).
• Controls both leaves in 2 leaf mode (Dip switch 2 in the ON position)
• Only opens the door, never closes it.
• Pause time is able to be re-set if this terminal is closed through a momentary contact. Then the time will be reset,
count down the pause time, and reclose.
• Ideal for exit wand or exit loop.
Operational Sequence for terminal with auto-close ON (Dip switch 1 in on position):
1. In closed position - momentary contact will open doors.
2. When opening - momentary contact will have no effect.
3. When stopped mid cycle from PUSH 1 or the Receiver - momentary contact will open the door.
4. When open with auto-reclose on - momentary contact will re-set pause time and will start counting again after
release of momentary contact.
5. When pause time countdown is stopped in open from a momentary contact of PUSH 1 or the Receiver momentary contact will have no effect.
6. When closing - momentary contact will re-open the door.
Operational Sequence for terminal with auto-close OFF (Dip switch 1 in off position):
1. In closed position - momentary contact will open doors.
2. When opening - momentary contact will have no effect.
3. When stopped mid cycle - momentary contact will open the door.
4. When open with auto-reclose off - momentary contact will have no effect.
5. When closing - momentary contact will re-open the door.
PUSH 1 and PUSH 2 – these terminals can hold as many normally open connections as
needed, they will be wired in parallel. They are used for keypads, push buttons, universal receivers, etc.
20
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Control Board Overview
Light:
Sends pulses of 24VDC only while door is running, and whether it is open or closed.
Motor 1:
L1-1, L1-2 = 24VDC power to primary motor
Motor 2:
L2-1, L2-2 = 24VDC power to secondary motor
Limit 1:
OL1 = Open limit for single motor or master (normally closed)
V+ = Common for limits, +12VDC
CL1 = Closed limit for single motor (normally closed)
Limit 2:
OL2 = Open limit for slave motor (normally closed)
V+ = Common for limits, +12VDC
CL2 = Closed limit for slave motor (normally closed)
Photocell:
Button:
Photo = Input for safety eye photo beam connection (normally closed)
GND = Ground for photocell power/ground for photo connection
V+ = +12VDC, Max 100 milliamps for photocell power
+24V = +24VDC, Max 200 milliamps for accessory power
PUSH 1 = Ground for Push 1 Accessory
*PUSH 1 / V+ is for push buttons, keypads, receivers, or any other dry and
momentary contact.
COM = Positive voltage +12VDC for Push 1 or Push 2 accessory (relay only, not
main power)
PUSH 2 = Ground for Push 2 accessory
*PUSH 2 / V+ is for exit wand, exit loops or other open only dry contact and
momentary contact
E_Lock:
Fuses:
(Right to left
on board)
Solenoid lock output - 12VDC (4 Amp max)
A = Positive B = Negative
F1 = 8A 250V, protects motor 1
F2 = 8A 250V, protects motor 2
F3 = 2A 250V, protects accessory output +24V
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
21
Control Board Overview
CAUTION! Do not r un 110V AC power direct to the boar d.
This will cause permanent damage to both boards and void your
warranty. Caution!
Display Indicators:
Lights off on board & stand by / normal operation
Lower right hand “dots” flashing normal pace:
Active / Awaiting command
EL: Sending voltage to EL ter minals (electr ic lock)
OP: Opening cycle
AU: Auto-reclose countdown
CL: Closing cycle
PH: Photo cell disr uption
Buzzer / Obstructions:
If the door(s) come in contact with an obstruction the door(s) will
reverse direction for 2 seconds and stop to allow the obstacle to be
cleared from the door path.
If the door(s) obstructs 3 times in a row the door(s) will go into a
hard shutdown mode and a buzzer alarm will sound. At this point
no accessories or remotes will be able to activate the door opener
until the door opener is reset by disconnecting primary power
battery.
22
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Accessory Wiring
The manufacturer instructions that come with your accessory should have markings for wires or terminals
to connect to the door opener. Please look for terminals named below in the instructions for the accessory.
Keypads, Receivers:
Normally Open (NO) or Input (INP) or Relay of entry device = COM ter minal (to r ight of PUSH1) of
PUSH block on door opener control board.
Common (COM) or Ground (GND) or Relay of entry device = PUSH1 ter minal of PUSH block on door
opener control board.
NOTE: If the power for the accessor y shar es a Gr ound wir e/ter minal with the r elay – Do Not power that
accessory off this control board (example: WKP-P keypad). Instead power that device with batteries.
24V Power positive (+) or (24V) or (PWR) of entry device = +24V ter minal of PHOTO block on door opener control board.
24V Power Negative (-) or (GND) or (PWR) of entry device = GND ter minal of PHOTO block on door
opener control board.
Push Button, Intercoms:
Normally Open (NO) or Input (INP) or Relay of entry device = COM ter minal (to r ight of PUSH1) of
PUSH block on door opener control board.
Common (COM) or Ground (GND) or Relay of entry device = PUSH1 ter minal of PUSH block on door
opener control board.
Push buttons do not require power and Intercoms draw too much power to power from the door opener.
Exit Wand/Sensor, Exit Loop Detector, Exit Device:
Normally Open (NO) or Input (INP) or Relay of exit device = COM ter minal (to r ight of PUSH2) of PUSH
block on door opener control board.
Common (COM) or Ground (GND) or Relay of exit device = PUSH2 ter minal of PUSH block on door
opener control board.
24V Power positive (+) or (24V) or (PWR) of exit device = +24V ter minal of PHOTO block on door opener
control board.
24V Power Negative (-) or (GND) or (PWR) or Shield wire of exit device = GND ter minal of PHOTO block
on door opener control board.
23
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Accessory Wiring
Photo Eye, Safety Edge, Safety Loop:
Normally Closed (NC) of safety device = Photo ter minal of PHOTO block on door opener contr ol boar d.
Common (COM) or Ground (GND) of safety device = GND ter minal of PHOTO block on door opener control board.
12V Power positive (+) or (12V) or (PWR) of safety device = V+ ter minal of PHOTO block on door opener
control board.
12V Power Negative (-) or (GND) or (PWR) of safety device = GND ter minal of PHOTO block on door
opener control board.
*Remove safety jumper from PHOTO terminal if using a safety device.
*12V is not a misprint, the V+ terminal has a 12V output.
Solenoid Door Lock:
Positive Lead of lock = A ter minal of E_LOCK block on door opener contr ol boar d.
Negative Lead of lock = B ter minal of E_LOCK block on door opener contr ol boar d.
Magnetic Door Lock: M agnetic door lock s must have their own power supply and their own
relay.
Coil of relay for magnetic lock = A ter minal of E_LOCK block on door opener contr ol boar d.
Coil of relay for magnetic lock = B ter minal of E_LOCK block on door opener contr ol boar d.
Connect positive lead of the power supply directly to the positive lead of the mag lock.
Connect negative lead of the power supply to the N/C terminal of the relay.
Connect the COM terminal of the relay to the negative lead of the mag lock.
24
Estate Swing E-SCAR1602 Heavy Duty Carriage Opener Instructions.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising