Wells | HMP6D-EU | Specifications | Wells HMP6D-EU Specifications

Wells HMP6D-EU Specifications
011A
WELLS BLOOMFIELD, LLC
10 Sunnen Dr., St. Louis, MO 63143
telephone: 314-678-6314
fax: 314-781-2714
www.wellsbloomfield.com
OWNERS MANUAL
BUILT-IN
RECTANGULAR
WARMERS
with
THERMOSTAT
CONTROL
MODELS
HMP6
HMP6D
HMP6ULD
MODEL: HMP6D
Includes
INSTALLATION
USE & CARE
EXPLODED VIEW
PARTS LIST
WIRING DIAGRAM
IMPORTANT: DO NOT DISCARD THIS MANUAL
This manual is considered to be part of the appliance and is to be given to the OWNER or
MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of
this appliance. Additional manuals are available from your WELLS DEALER.
THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR
INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any
questions concerning installation, operation or maintenance of this equipment.
p/n 2M-308012 Rev. (-)
M011A.01
120214
LIMITED WARRANTY STATEMENT
Unless otherwise specified, all commercial cooking
equipment manufactured by WELLS BLOOMFIELD, LLC is
warranted against defects in materials and workmanship
for a period of one year from the date of original installation
or 18 months from the date of shipment from our factory,
whichever comes first, and is for the benefit of the original
purchaser only.
The prices charged by Wells Bloomfield for its products
are based upon the limitations in this warranty. Seller’s
obligation under this warranty is limited to the repair of
defects without charge by a Wells Bloomfield factory
authorized service agency or one of its sub-service
agencies. This service will be provided on customer’s
premises for non-portable models. Portable models (a
device with a cord and plug) must be taken or shipped
to the closest authorized service agency, transportation
charges prepaid, for service. In addition to restrictions
contained in this warranty, specific limitations are shown in
the Service Policy and Procedure Guide. Wells Bloomfield
authorized service agencies are located in principal cities.
This warranty is valid in the United States and Canada and
void elsewhere. Please consult your classified telephone
directory, your foodservice equipment dealer or contact:
THIS WARRANTY IS THE COMPLETE AND ONLY
WARRANTY, EXPRESSED OR IMPLIED IN LAW
OR IN FACT, INCLUDING BUT NOT LIMITED TO,
WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE, AND/OR FOR
DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES IN
CONNECTION WITH WELLS BLOOMFIELD PRODUCTS.
This warranty is void if it is determined that, upon inspection
by an authorized service agency, the equipment has been
modified, misused, misapplied, improperly installed, or
damaged in transit or by fire, flood or act of God. It also
does not apply if the serial nameplate has been removed,
or if service is performed by unauthorized personnel.
Wells Bloomfield, LLC
10 Sunnen Dr., St. Louis MO 63143 USA
phone (314) 678-6314 or fax (314) 781-2714
for information and other details concerning warranty.
1.
2.
3.
4.
5.
6.
Resetting of safety thermostats, circuit breakers, over
load protectors, and/or fuse replacements are not
covered by this warranty unless warranted conditions
are the cause.
All problems due to operation at voltages or phase
other than specified on equipment nameplates are not
covered by this warranty. Conversion to correct voltage
and/or phase must be the customer’s responsibility.
All problems due to electrical connections not made
in accordance with electrical code requirements and
wiring diagrams supplied with the equipment are not
covered by this warranty.
Replacement of items subject to normal wear, to
include such items as knobs, light bulbs; and, normal
maintenance functions including adjustments of
thermostats, adjustment of micro switches and
replacement of fuses and indicating lights are not
covered by warranty.
Damage to electrical cords and/or plug due to exposure
to excessive heat are not covered by this warranty.
Full use, care, and maintenance instructions supplied
with each machine. Noted maintenance and
preventative maintenance items, such as servicing
and cleaning schedules, are customer responsibility.
Those miscellaneous adjustments noted are customer
responsibility. Proper attention to preventative
maintenance and scheduled maintenance procedures
will prolong the life of the appliance.
7. Travel mileage is limited to sixty (60) miles from an
Authorized Service Agency or one of its sub-service
agencies.
8. All labor shall be performed during regular working
hours. Overtime premium will be charged to the buyer.
9. All genuine Wells replacement parts are warranted
for ninety (90) days from date of purchase on nonwarranty equipment. This parts warranty is limited only
to replacement of the defective part(s). Any use of
non-genuine Wells parts completely voids any
warranty.
10. Installation, labor, and job check-outs are not
considered warranty and are thus not covered by this
warranty.
11. Charges incurred by delays, waiting time or operating
restrictions that hinder the service technician’s ability to
perform service are not covered by warranty. This
includes institutional and correctional facilities.
SHIPPING DAMAGE CLAIM PROCEDURE
2.
NOTE: For your protection, please note that equipment
in this shipment was carefully inspected and packaged
by skilled personnel before leaving the factory. Upon
acceptance of this shipment, the transportation company
assumes full responsibility for its safe delivery.
Regardless of the extent of the damage.
1.
CONCEALED LOSS OR DAMAGE: if damage is
unnoticed until the merchandise is unpacked, notify
the transportation company or carrier immediately, and
file “CONCEALED DAMAGE” claim with them. This
should be done within fifteen (15) days from the date
the delivery was made to you. Be sure to retain the
container for inspection.
IF SHIPMENT ARRIVES DAMAGED:
1.
FILE CLAIM FOR DAMAGE IMMEDIATELY:
VISIBLE LOSS OR DAMAGE: Be certain that any
visible loss or damage is noted on the freight bill or
express receipt, and that the note of loss or damage is
signed by the delivery person.
xi
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS
TABLE OF CONTENTS
WARRANTY
FEATURES & OPERATING CONTROLS
PRECAUTIONS & GENERAL INFORMATION
AGENCY LISTING INFORMATION
INSTALLATION
OPERATION
MAINTENANCE INSTRUCTIONS
CLEANING INSTRUCTIONS
TROUBLESHOOTING SUGGESTIONS
EXPLODED VIEW & PARTS LIST
WIRING DIAGRAM
PARTS & SERVICE
CUSTOMER SERVICE DATA
xi
2
3
3
4
6
7
8
10
11
14
17
17
INTRODUCTION
Thank You for purchasing this Wells Bloomfield appliance.
Proper installation, professional operation and consistent maintenance of this appliance will ensure that it
gives you the very best performance and a long, economical service life.
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
This manual contains the information needed to properly install this appliance, and to use and care for the
appliance in a manner which will ensure its optimum performance.
SPECIFICATIONS
MODEL
HMP6, HMP6D
HMP6UL, HMP6ULD
VOLTS
AMPS
WATTS
120 VAC 1ø
6.3A
750W
240 VAC 1ø
2.4A
575W
120VAC 1ø
6.3A
750W
240 VAC 1ø
2.4A
575W
1
POWER SUPPLY CORD
NOT SUPPLIED
NOT SUPPLIED
FEATURES & OPERATING CONTROLS
A.
THERMOSTAT
1. On THERMOSTATICALLY CONTROLLED warmers, power is
applied to the heating element according to the control knob
position and the actual temperature at the temperature sensing
thermobulb.
INDICATOR
LIGHT
2. The desired temperature is controlled by rotating the
TEMPERATURE CONTROL KNOB. The knob has a numeric
scale, where higher numbers correspond to higher temperature.
TEMPERATURE
CONTROL
KNOB
3. On warmers equipped with an INDICATOR LIGHT, the light will
glow when the thermostat is calling for heat (i.e. the element is
energized).
IL2468
4. The TEMPERATURE CONTROL KNOB will rotate
approximately 300º, and will reach a “stop” at both ends.
The OFF position is marked.
NOTE: The dial position is an indication of the temperature
setting. Actual temperature will vary depending upon the type of
product and food consistency.
B.
MOUNTING
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
HMP6 Series warmers require a cutout and mounting holes in the
counter top.See the Installation Instructions, supplied with the
particular warmer, for details.
2
PRECAUTIONS AND GENERAL INFORMATION
This appliance is intended for use in commercial establishments only.
WARNING:
WA
This appliance is intended to hold pre-heated food for human
consumption. No other use is recommended or authorized by the
manufacturer or its agents.
SHOCK HAZARD
SHO
Operators of this appliance must be familiar with the appliance use,
limitations and associated restrictions. Operating instructions must be
read and understood by all persons using or installing this appliance.
Cleanliness of this appliance is essential to good sanitation. Read and
follow all included cleaning instructions and schedules to ensure the
safety of the food product.
Disconnect this appliance from electrical power before performing any
maintenance or servicing.
This appliance is not jet stream approved. Do not direct water jet
or steam jet at this appliance, or at any control panel or wiring. Do
not splash or pour water on, in or over any controls, control panel or
wiring.
Exposed surfaces of this appliance can be hot to the touch and may
cause burns.
Do not operate this appliance if the control panel is damaged. Call
your Authorized Wells Service Agent for service.
The technical content of this manual, including any wiring diagrams,
schematics, parts breakdown illustrations and/or adjustment
procedures, is intended for use by qualified technical personnel.
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
Any procedure which requires the use of tools must be performed by a
qualified technician.
This manual is considered to be a permanent part of the appliance.
This manual and all supplied instructions, diagrams, schematics,
parts breakdown illustrations, notices and labels must remain with the
appliance if it is sold or moved to another location.
This appliance is made in the USA. Unless otherwise noted, this
appliance has American sizes on all hardware.
All servicin
servicing requiring
access to non-insulated
electrical components must
be performed by a factory
authorized technician.
DO NOT open any access
panel which requires the use
of tools. Failure to follow this
warning can result in severe
electrical shock.
CAUTION:
CA
RIS OF
RISK
DAMAGE
DAM
DO NOT connect or energize
this appliance until all
installation instructions are
read and followed. Damage
to the appliance may result
if these instructions are not
followed.
CAUTION:
CA
HOT SURFACE
Exposed surfaces can be hot
to the touch and may cause
burns.
AGENCY LISTING INFORMATION
Refer to the product nameplate for the specific appliance for agency
listings. In general:
STD 4
This appliance conforms to NSF Standard 4 for sanitation only if
installed in accordance with the supplied Installation Instructions.
UL Listed warmers are U Listed under UL File E6070.
Underwriters Laboratory recognized (
) warmers (UL File E6070) Since the warmer is only a single component of a complete installation,
the finished installation of an
unit requires additional evaluations to
Underwriters Laboratory standards.
E6070
UL Listed Warmers
E6070
UL Recognized Warmers
3
INSTALLATION
WARNING:
WA
RISK OF INJURY
RIS
Installation procedures must
be performed by a qualified
technician with full knowledge
of all applicable electrical and
plumbing codes. Failure can
result in personal injury and
property damage.
CAUTION
CA
FIRE HAZARD
Av
Avoid storing
flammable or combustible
materials in, on or near the
appliance.
IMPORTANT: For warmers
installed in plastic counter
tops, the counter material
must be protected from the
heat of the warmer in order to
prevent discoloration and/or
deterioration. Wellsloks are
not suitable for this purpose.
The installer should contact
the manufacturer or distributor
of the countertop material for
specific instructions.
IMPORTANT: Wellslok
Extension Kits must be used
ONLY with UL Listed warmers
approved for installation in
wood counter tops. Refer to
the Installation Instructions
provided with the warmer.
UNPACKING & INSPECTION
Carefully remove the appliance from the carton. Remove all protective
plastic film, packing materials and accessories from the Appliance
before connecting electrical power or otherwise performing any
installation procedure.
Carefully read all instructions in this manual and the Installation
Instruction Sheet packed with the appliance before starting any
installation.
Read and understand all labels and diagrams attached to the
appliance.
Carefully account for all components and accessories before discarding
packing materials. Store all accessories in a convenient place for later
use.
INSTALLATION NOTES
1.
Installation and start up of built-in warmers MUST be performed
by an authorized installation company.
2.
It is the responsibility of the installer to verify that this warmer
installation is in compliance with the specifications listed in this
manual and on the specification sheet provided.
3.
It is the RESPONSIBILITY OF THE INSTALLER to check with
the authority having jurisdiction, in order to verify that this warmer
installation is in compliance with local code requirements.
4. Drain installation must meet all applicable local, state and federal
plumbing codes and ordinances.
5. Refer to Installation Instructions included with the warmer for
Underwriters Laboratories conditions of acceptability, electrical
requirements and other installation concerns.
BUILT-IN WARMERS
1.
This is a GENERAL GUIDE. For specific cutout dimensions
and other installation details, refer to the Installation Instructions
supplied with the warmer.
2. Cutout dimensions for warmer units and control panels are listed
on the Installation Instructions provided with the warmer.
3. Verify style of control panel (e.g square, rectangular) before
making cutout.
NOTE: Cutout dimensions are different for square and
rectangular control panels, for UL LISTED units and UL
Recognized units, and for wood and metal counters. Verify the
dimensions are correct for the installation before making the
cutout.
4
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
NOTE: DO NOT discard
the carton or other packing
materials until you have
inspected the appliance for
hidden damage and tested it
for proper operation. Refer to
SHIPPING DAMAGE CLAIM
PROCEDURE on the inside
front cover of this manual.
INSTALLATION
4.
a.
b.
c.
Top-Mounted Warmers
Verify that provided sealants are applied to the underside of the
warmer top flange prior to setting the unit into the cutout.
After installation, verify that all supplied fasteners and other
mounting hardware is properly installed and tightened.
Apply a thin bead of food-grade silicone sealant around the flange
to seal it to the counter.
ELECTRICAL INSTALLATION
1.
Refer to the product nameplate. Verify the electrical service
power. Voltage and phase must match the nameplate
specifications. Wiring the warmer to the wrong voltage can
severely damage the unit or cause noticeably decreased
performance.
2.
Available electrical service amperage must meet or exceed the
specifications listed on the specification sheet provided with the
warmer.
3.
Warmer and control unit must be connected to an appropriate
building ground. Ground connection will be marked “GND” or
”
“.
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
NOTE: Wire gauge, insulation type and temperature rating ,
as well as type, size and construction of conduit, must meet
or exceed applicable specifications of local codes and of the
National Electrical Code.
PLUMBING INSTALLATION
For use in the State of Massachusetts, this appliance must be installed
in compliance with Massachusetts Fuel Gas and Plumbing Code
CMR 248.
1.
IMPORTANT: All plumbing installations must be performed by
a qualified plumber.
2.
For units equipped with a DRAIN LINE: Some jurisdictions may
require an approved air gap or other back-flow prevention device
in the drain. It is the responsibility of the plumber to determine
such requirement, to provide and properly install the required
device.
5
NOTE: Damage caused
by leaks due to improper
installation is NOT covered by
warranty.
CAUTION:
SHOCK HAZARD
The ground lug of this
appliance must be connected
to a suitable building ground.
IMPORTANT:
Contact a licensed electrician
to install and connect electrical
power to the appliance.
IMPORTANT:
Damage due to being
connected to the wrong
voltage or phase is NOT
covered by warranty.
IMPORTANT: Electrical
installation other than as
specified on the specification
sheet will void the UL listing,
and may void the warranty.
NOTE: Plumb connections
must be made in compliance
with all Federal, State and
Local Plumbing Codes and
Ordinances.
OPERATION
HOT SURFACE
Exposed surfaces can be hot
to the touch and may cause
burns.
CAUTION:
SHOCK HAZARD
DO NOT splash or pour water
onto control panel or wiring.
WET OR DRY OPERATION for WARMERS
1. Carefully read the description of the warmer operation on the
specification sheet.
2. a. Most warmers are designed for WET OR DRY operation.
b. Warmers may be used wet, or may be used dry. However
warmers may NOT be used wet-to-dry or dry-to-wet unless they
have been allowed to cool to room temperature between the
change in wet or dry operation.
c. Wells Manufacturing recommends operating WET for consistent
food heating.
d. If your wet-operation warmer is allowed to run dry, turn it OFF and
allow to cool to room temperature before adding water.
3. If the warmer is to be used for WET operation, add approximately 1” of
hot tap water before turning the warmer on. Use of hot water will allow
a faster preheat.
a. Check the water level frequently and add hot water as
necessary to prevent the warmer from running dry. Do not
add water to the warmer if it has run dry.
Always use an inset.
DO NOT place food directly
into the warmer.
Always pour hot water into the
warmer before it is preheated.
DO NOT pour water into a
dry, heated warmer. This may
damage the unit.
DO NOT put ice into a
warmer pan. This will cause
condensation on the inside of
the warmer. Damage caused
by condensation is NOT
covered by warranty.
Stir thick food items frequently
to keep food heated uniformly.
Keep insets covered to
maintain food quality and
temperature.
4.
b. If your wet-operation warmer is allowed to run dry, turn it
OFF and allow to cool to room temperature before adding
water.
Damage caused by allowing a wet-operation warmer to run dry,
is NOT covered by warranty. Damage caused by adding water
to a dry warmer when hot is NOT covered by warranty.
PRE-HEATING THE WARMER
1. Place desired pan(s) or inset(s) with appropriate adapter top on
warmer.
2. Turn temperature control to highest temperature setting.
3. Allow warmer to preheat for approximately 30 minutes, then set
the control for the desired temperature. Be sure to keep the warmer
covered during preheat and operation.
OPERATION
1. Always use an inset. DO NOT place food directly into the
warmer.
2. Check water level in wet-operation warmer frequently during
use. Running warmers dry will lower the temperature of the
food in the insert pan, and may damage the warmer.
3. Alternating between wet and dry operation in any individual
warmer is NOT recommended.
4. DO NOT use metal tools, steel wool, or caustic or abrasive
cleanser to clean warmer pan.
6
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
CAUTION:
MAINTENANCE INSTRUCTIONS
CARE OF STAINLESS STEEL
Stainless steel is a marvelous material: strong, lustrous and low maintenance. With
a minimum of care, it will normally retain its beauty and durability for the life of the
equipment. In some applications, however, special care is required in order to maintain
stainless steel’s special properties.
External components, such as cabinets and control panels, are finished with a grain
pattern. This pleasing finish is best maintained by cleaning with a non-abrasive
cleanser applied with a soft cloth. Rub only in the direction of the grain. In the absence
of visible grain, rub only along the longest axis of the appliance.
Restore stainless steel’s luster by applying a polish specifically made for stainless steel.
Spray on, wipe off with a soft cloth, rubbing in the direction of the grain.
Never use metal implements, wire brushes, abrasive scratch pads or steel wool to clean
stainless steel.
Warmer pans, insets and other vessels are subject to a harsher environment. Wells
Manufacturing uses an very high quality stainless steel (#304DDQ) for our food warmer
pans. Even the highest quality stainless steel, however, is mostly iron, and will rust, pit
and corrode under the following conditions:
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
•
•
Poor Water Quality: Hard water (water with a high content of dissolved minerals)
will leave mineral deposits when allowed to dry. Calcium (lime) can buildup on
heated surfaces, even under water. If left unattended, hard water spots and lime
buildup can lead to rusting, corrosion and pitting.
Contact with Chlorides: Chlorides (specific compounds of chlorine) are found in
food, table salt and many cleansers. Chlorides can attack the surface of stainless
steel, resulting in corrosion and pitting.
Keep your stainless steel warmers clean and free from calcium buildup.
Use alkaline, alkaline chlorinated or non-chloride cleanser.
Use citric acid-based cleaners to remove calcium deposits.
For additional information, please read the NAFEM Stainless Steel Equipment and
Cleaning Guide. Contact NAFEM at :
North American Association of Food Equipment Manufacturers
401 N. Michigan Avenue
Chicago, Illinois 60611-4267
(312) 644-6610
7
CLEANING INSTRUCTIONS
CAUTION:
CA
SHO
SHOCK HAZARD
Do NOT spl
splash or pour water
into or over any control panel
or wiring.
CAUTION:
CA
DAILY CLEANING INSTRUCTIONS
PREPARATIONS: Turn control knob(s) to OFF. Allow warmer to cool
before proceeding.
Remove any insets, pans and/or adapter tops.
Drain or remove water from well if used for
wet operation.
FREQUENCY:
Minimum - daily.
TOOLS:
Mild Detergent
Solution: 10 Parts Warm Water to 4 Parts Vinegar
Plastic Scouring Pad
Clean Cloth or Sponge
Food-Grade Silicone Sealant
SHOCK HAZARD
SH
Disconnect warmer from
electric power before cleaning
CAUTION:
CA
BURN HAZARD
BU
1. Wipe entire unit down using a clean cloth or sponge and mild detergent.
2.
Use a plastic scouring pad to remove any hardened food particles
or mineral deposits. IMPORTANT: Do NOT use steel wool for cleaning.
3.
Rinse warmer thoroughly with a vinegar and water solution to neutralize
all detergent cleanser residue.
4.
Inspect warmer flange-to-counter seal. Reseal with food-grade silicone
sealant if necessary. Failure to do so may allow grease and water to
leak into insulation and heating element, causing a potential fire and/or
electric shock hazard.
5.
Inspect warmer tank for damage. Damage to the outer body may
allow grease and water to leak into insulation and heating element,
causing a potential fire and/or electric shock hazard. Contact your
Authorized Wells Service Agency to inspect warmer if water or grease
contamination is suspected.
6.
Close drain valve. Add proper amount of warm water. Turn control
knob(s) ON and check for proper operation.
8
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
warm to cool
Allow warmer
completely before cleaning.
CLEANING INSTRUCTIONS
WEEKLY CLEANING INSTRUCTIONS
CAUTION:
CA
PREPARATIONS:
CH
CHEMICAL
BURN
HAZARD
HA
Remove any insets, pans and/or adapter tops.
Drain or remove water from well if used for
wet operation.
FREQUENCY:
Weekly, or whenever lime or scale is seen
accumulating on the sides of the warmer
pans.
TOOLS:
Commercial Delime Cleaner
Plastic Scouring Pad
Clean Cloth or Sponge
1.
Add water to pans until water is at normal operating level
(1” - 1 1/2” deep) or covers accumulated scale.
2.
Heat water to maximum temperature (190ºF or higher).
3.
Pour contents of one package of commercial delime cleaner into
each warmer pan. Stir to dissolve cleaner. Turn heat control OFF.
Cover pans.
4.
Allow solution to soak at least one hour, or overnight for heavy
scale buildup.
5.
Drain hot water from pans. Scrub with a plastic scouring pad.
Rinse thoroughly with hot water, then dry.
Refill pans with hot tap water and resume operation.
7.
Heavy scale buildup may require additional treatments.
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
6.
9
Deilimng chemicals may be
caustic. Wear appropriate
personal protective equipment.
Follow cleaner manufacturer’s
instructions for safest use.
TROUBLESHOOTING SUGGESTIONS
SYMPTOM
POSSIBLE CAUSE
SUGGESTED REMEDY
No power to warmer
Circuit breaker off or tripped
Reset circuit breaker
Warmer will not heat
Temperature control not set
Set control to desired temperature
Wet insulation
Verify flange-to counter seal is sound, or
reseal with food-grade silicone sealant
Pan leaking or other internal damage
Contact your Authorized Wells Service
Agency for repairs
Internal damage
Contact your Authorized Wells Service
Agency for repairs
Mineral deposits on pan acting as a
insulator
Clean pan(s) with delime cleaner
Wired to wrong voltage
Verify supply voltage - must match
voltage on warmer nameplate
Drain valve not fully closed
Check drain valve for debris and close
fully
Drain valve damaged or pan(s) leaking
Contact your Authorized Wells Service
Agency for repairs
Warmer trips circuit breaker
Warmer slow to heat
Drain-equipped unit will not
hold water
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
There are no user-serviceable components in this appliance.
In all instances of damage or malfunction, contact your Authorized Wells Service Agency for repairs.
10
EXPLODED VIEW & PARTS LIST
MODEL HMP-6
PAN ASSEMBLY
P2-305802
ELEMENT PAN
WS-505643
ELEMENT CLIP
2C-30397
STRAIGHT
CONDUIT FITTING
2K-37748X
PILOT LIGHT
RETAINER CLIP
2C-63271
K-TYPETHERMOSTAT CONTROL
2T-38968
RED LIGHT
SIGNAL
2J-35687
POP
RIVET
2C-34284
THERMOBULB
BRACKET
D8-303352
HI
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
HEATING ELEMENT
2N-45431UL
WE
LL
S
CONTROL KNOB
ASSEMBLY
2R-40498
ELEMENT
PAN COVER
P2-305642
MODEL:HMP-6
IL2005a
11
EXPLODED VIEW & PARTS LIST
MODEL HMP-6D
DRAIN SCREEN
ASSEMBLY
P2-31869
PAN ASSEMBLY
P2-41463
PILOT LIGHT
RETAINER CLIP
2C-43271
K-TYPE
THERMOSTAT
2T-38968
WE
LL
S
POP RIVET
2C-34284
CONTROL KNOB
ASSEMBLY
2R-40498
HEATING
ELEMENT
2N-45431UL
ELEMENT
CLIP
2C-30397
THERMOSTAT
PLATE
P2-41461
STRAIGHT
CONDUIT FITTING
2K-37748X
ELEMENT COVER
P2-41462
MODEL:HMP-6D
IL2006a
12
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
HI
RED LIGHT
SIGNAL
2J-35687
EXPLODED VIEW & PARTS LIST
MODEL HMP-6ULD
Wireset for HMP6DU6
use P2-41317A
DRAIN SCREEN
ASSEMBLY
P2-31869
PAN ASSEMBLY
P2-41463
K-TYPETHERMOSTAT
2T-38968
(6’ use 2T-46551)
CONTROL BOX
P2-306959
PLATE,THERMO
P2-45614
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
RED LIGHT
SIGNAL
2J-35687 CONTROL
PANEL
I7-Z12221
ELEMENT CLIP
2C-30397
HEATING
ELEMENT
2N-45431UL
POP RIVET
2C-34284
CONTROL KNOB
ASSEMBLY
2R-40498
ELEMENT COVER
P2-45611
90 DEGREE BEND
CONDUIT FITTING
2K-34136X
(6’ use 2K-33996X)
MODEL:HMP-6ULD
IL2004b
13
WIRING DIAGRAM
HMP-6 Series
14
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
NOTES
15
NOTES
16
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
PARTS & SERVICE
DESCRIPTION
PART NO.
ACCESSORIES
IMPORTANT: Use only factory
authorized service parts and
replacement filters.
For factory authorized
DRAIN VALVE EXTENSION KIT, extension from
drain to counter front with remote handle, for use
with “D” models only, excluding “DM” models
5P-20385
DRAIN SCREEN
P2-31869
OPTIONAL 72” WIRING, thermostatically controlled warmers
**
contact factory customer service for availability
**
service, or to order factory
authorized replacement parts,
contact your Wells authorized
service agency, or call:
Wells Bloomfield, LLC
10 Sunnen Dr.
St. Louis MO 63143 USA
Service Dept.
phone: (314) 678-6314
fax:
(314) 781-2714
M011A.01 2M-308012 Owners Manual for Built-In Rectangular T’Stat Warmers
Service Parts Department
can supply you with the name
and telephone number of
the WELLS AUTHORIZED
SERVICE AGENCY
nearest you.
CUSTOMER SERVICE DATA
please have this information available if calling for service
RESTAURANT _____________________________ LOCATION _____________
INSTALLATION DATE ________________________ TECHNICIAN ___________
SERVICE COMPANY ________________________________________________
ADDRESS ___________________________ STATE ______ ZIP__________
TELEPHONE NUMBER (_____)_____-_________
EQUIPMENT MODEL NO. _______________
EQUIPMENT SERIAL NO. _______________
VOLTAGE: (check one)
120
208
17
240
WELLS BLOOMFIELD, LLC
10 Sunnen Dr., St. Louis, MO 63143
telephone: 314-678-6314
fax: 314-781-2714
www.wellsbloomfield.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising