TPRIII E Electronic Panel Instructions

TPRIII E Electronic Panel Instructions
 Contact Details Please note that some of the contact details on this PDF document may not be current. Please use the following details if you need to contact us: Telephone: 0844 879 3588 Email: [email protected] The Help Centre section of this website also features a wide range of information which may be of use to you and is available 24 hours a day. It includes: • Operating and installation instructions downloads • Request a repair • Where to buy our products • Literature downloads • Heating requirement calculator www.credaheating.co.uk/help‐centre A division of GDC Group Ltd
Millbrook House Grange Drive Hedge End Southampton SO30 2DF
www.credaheating.co.uk
Registered No: 1313016 England
VAT GB 287 1315 50004
EEE Producer Registration Number –
WEE/GE0057TS
Paper from sustainable sources
Installation and Operating Instructions
INCPUKP5EL Issue 1
TPR III E Electronic Panel Heaters
Dimensions
(millimetres)
Model(s)
Watt
A
B
TPR III 500E
0.5kW
450
108
TPR III 750E
0.75kW
620
108
TPR III 1000E
1.0kW
620
108
TPR III 1250E
1.25kW
688
108
TPR III 1500E
1.5kW
688
108
TPR III 2000E
2.0kW
860
108
Fig. 1
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electrical shock, and injury to persons, including the
following:
IMPORTANT – The wall brackets supplied with the
appliance must be used.
WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE
SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING
POOL.
IMPORTANT – If the heater is installed in a room
containing a bath or shower, it must be so installed that
switches and other controls cannot be touched by a
person using a bath or shower.
Do not use outdoors.
Do not locate the heater immediately below a fixed socket
outlet or connection box.
Do not cover the heater. Do not place material or
garments on the heater, or obstruct the air circulation
around the heater, for instance by curtains or furniture,
as this could cause overheating and a fire risk.
NEVER cover or obstruct in any way the heat outlet slots
at the top of the heater or the air inlet slots in the base of
the heater.
WARNING – THE SURFACES OF THIS HEATER CAN BE HOT.
Momentary contact with any part of the heater should
not cause injury. However, aged or infirm persons or
young children should not be left unsupervised in the
vicinity of the heater unless a suitable guard is fitted.
This appliance is not intended for use by children or
other persons without assistance or supervision if their
physical, sensory or mental capabilities prevent them
from using it safely. Children should be supervised to
ensure that they do not play with the appliance.
Note that due care and consideration must be taken
when using this heater in series with a thermal control,
a program controller, a timer or any other device that
switches on the heat automatically, since a fire risk
exists when the heater is accidentally covered or
displaced.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or a similarly qualified
person in order to avoid a hazard.
Electrical
WARNING – THIS APPLIANCE MUST BE EARTHED
The electrical installation must be carried out by a competent
electrician, and be in strict accordance with the current I.E.E.
regulations for Electrical Equipment in Buildings.
The wires in this mains lead are coloured in accordance
with the following code :
GREEN AND YELLOW :
EARTH
BLUE :
NEUTRAL
BROWN :
LIVE
BLACK :
PILOT WIRE
- see also ‘Pilot Wire Connection’.
The heater is fitted with a length of flexible cable type H05VVF size 4 x 1.0mm2 for connection to the fixed wiring of the
premises through a suitable connection box positioned
adjacent to the heater.
The supply circuit to the heater must incorporate a double
pole isolating switch having a contact separation of at least
3mm.
Pilot Wire Connection
The BLACK control wire is designed to carry a signal from
slot in or wall mounted Creda programmers. If, however a
programmer is not being used, the pilot wire should be
isolated in accordance with the current IEE Wiring
Regulations.
IMPORTANT - DO NOT connect the BLACK pilot wire to earth.
Care should be taken with the installation of the pilot wire(s)
as when switching to background (set back) they become
energised at 240V although only at a current of less than
100mA. In every case a suitable means of isolation must be
provided for the pilot wire and marked to indicate that two
sources of supply may be present at the heater.
Where pilot wires are installed separately from the heater
final sub-circuit they should be protected, double insulated
and carry their own integral earth continuity conductor.
Supplementary Earth Bonding
Should Equipotential Earth Bonding be required the earthing
conductor in the supply cord is deemed to provide the
supplementary bonding connection (see Regulation 701, 17th
Edition I.E.E. Wiring regulations).
General
The TPR III E Electronic panel heater is designed for wall
mounting on the wall brackets supplied. It should only be
operated when in the upright position as shown.
All models are splashproof to IP24 standard.
Before connecting the heater check that the supply voltage is
the same as that stated on the heater.
Wall Mounting
IMPORTANT – The wall brackets supplied with the appliance
must be used. The heater should be positioned observing
the minimum clearances stated around the heater - see
Fig. 1.
Turn on the heater using the ‘ ’ button and rotate the
thermostat knob to the desired position. When the room
temperature has reached the desired level, the power to the
elements will be reduced, the heater will then maintain the
room temperature at the chosen level.
NOTE - Should your heater fail to come on when the thermostat
knob is at a low setting, this may be due to the room
temperature being higher than the thermostat setting.
Background Temperature
DO NOT locate the heater immediately below a fixed socket
outlet or connection box.
When used in conjunction with a remote programming device
supporting a background/setback setting, the heater will
automatically operate at a room temperature setting of 50C
less than the thermostat setting when the programme is in
background/setback mode.
1.
Limiting the thermostat setting
2.
3.
4.
Remove wall mounting bracket from the back of the
heater by depressing the spring latch at the top of
each bracket - see Fig. 2.
Fix the wall bracket securely to the wall through the
four screw holes provided.
Present the heater to the wall bracket, and engage
lower slots in the back with bracket.
Raise the heater to upright position and push the
heater onto brackets to engage top latch.
The installer may wish to limit the heat selection knob
movement for the operator. This may be achieved by
unclipping the plastic knob cap and removing the two plastic
pins (see Fig.4) using pliers and inserting them in the
preferred holes to limit the knob movement. Replace the
plastic cap.
Fig. 2
Operation
Switching On the Heater (see Fig. 3)
The button marked ‘ ’ controls the electricity supply to the
electronic thermostat. An indicator beside the ‘ ’ button
shows when the unit is powered ‘ON’.
Setting Desired Temperature (see Fig. 3)
The heater is fitted with an adjustable thermostat enabling
the room temperature to be controlled by adjusting the rotary
knob accordingly. The ‘MIN’ setting represents a room
temperature of approximately 50C and may be used for
protection against frost. The ‘MAX’ setting represents a room
temperature of approximately 300C. The ‘ ’ symbol glows
when the elements are actually heating.
Fig. 4
MIN
MAX
Fig. 3
Lift the cover away from the heater (see Fig. 6) to reveal the
slide in compartment.
Notes to the Installer
Test Mode
When the TPR III E Panel Heater is connected via a pilot wire
system, the test mode allows the installer to check whether
the heater is responding correctly to the incoming pilot wire
signal.
Before switching the heater on at the mains, place the
thermostat knob in the 'MAX' position, the press and hold the
‘ ’ button whilst switching on the mains.
The unit will now enter a test state for 4 mins. During this test
state the ‘ ’ neon will indicate the pilot wire status:
NEON
PILOT WIRE
CONTROLLER MODE
Neon on -
ON
Neon off -
OFF
Neon flashing fast approx every 0.1sec -
FROST
Neon flashing slow approx every 0.5 sec -
SETBACK
Fig. 6
Insert the timer module into the slot ensuring it is positively
located in position - see Fig. 7.
Timer Modules
Optional timer modules are available for use with the TPR III
E range of panel heaters - see separate User Instructions
for details on the operation of each timer module.
Switch the heater on at the mains supply.
Before fitting a control module switch the heater off at the
mains supply.
To insert a module, the plug-in protective cover on the right
hand side of the thermostat unit at the back of the heater
must first be removed.
Insert a flat-head screwdriver into the side of the cover and
prise away from the heater - see Fig. 5.
Fig. 5
Fig. 7
Safety - Overheat protection
For your safety this appliance is fitted with a thermal cut-out.
In the event that the product overheats for some reason, the
cut-out prevents excessive temperatures on the product by
cutting the power to the heater. Once the heater has cooled
down, it will reset automatically, it will continue to cycle on
and off automatically until the reason for overheating is
removed.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE CLEANING THE HEATER.
Before commencing cleaning, unplug the heater and allow it
to cool. Disconnect the electricity supply to the appliance.
The outside can be cleaned by wiping it over with a soft damp
cloth and then dried. Do not use abrasive cleaning powders
or furniture polish, as this can damage the surface finish.
To release heater from the wall bracket for cleaning or
redecoration, depress latch on both brackets (see Fig. 2)
and hinge forward.
After Sales Service
Your product is guaranteed for one year from the date of
purchase.
Within this period, we undertake to repair or exchange this
product free of charge provided it has been installed and
operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
Should you require after sales service you should contact
our customer services help desk on 0845 604 2399. It would
assist us if you can quote the model number, series, date of
purchase, and nature of the fault at the time of your call. The
customer services help desk will also be able to advise you
should you need to purchase any spares.
Please do not return a faulty prduct to us in the first instance
as this may result in loss or damage and delay in providing
you with a satisfactory service.
Please retain your receipt as proof of purchase.
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility
(EMC) EN55014, EN60555-2, EN60555-3. These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC.
CREDA HEATING
MILLBROOK HOUSE
GRANGE DRIVE
HEDGE END
SOUTHAMPTON
SO30 2DF
TEL: 0845 604 2399
FAX: 01489 773064
WEBSITE: WWW.CREDAHEATING.CO.UK
Republic of Ireland Tel:
01 842 4833
[c] GDC Group Ltd,
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of GDC Group Ltd.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement