Scantech | V-1020 | User`s manual | Scantech V-1020 User`s manual

Scantech V-1020 User`s manual
User’s
Manual
VEGA V-1020 Area Imager
Handheld Bar code Scanner
Scantech-ID BV
Vanadiumweg 22,
3812PZ
Amersfoort
The Netherlands.
Tel:+31-33-4698400
Fax:+31-33-4650615
E-mail:info@scantech-id.com
www.scantech-id.com
HEAD QUARTER
CHAMPTEK INCORPORATED
5/F, No.2 Alley 2, Shih-Wei
Lane,
Chung Cheng Rd., Hsin Tien
City,Taipei 231, Taiwan
Tel:+886-2-2219-2385
Fax:+886-2-2219-2387
E-mail:sales@champtek.com
www.champtek.com
CHINA
CHAMPTEK INCORPORATED
#901, No. 39, Wuzhong Rd.,
Shanghai 200235, China
Tel: +86-21-5489-0021
Fax: +86-21-5489-1833
Notice: The manufacturer shall not be liable for
technical or editorial errors or omissions contained
herein; nor for incidental or consequential damages in
connection with the furnishing, performance or use of
the publication.
User’s Installation and Configuration
Manual
Scantech-ID
Copyright © 2009, Scantech-ID BV.
This manual is copyrighted, with all rights reserved. Under the copyright
laws, this manual may not, in whole or in part, be copied, photocopied,
reproduced, translated or converted to any electronic medium or machine
readable form without prior written consent of Scantech-ID BV.
Limited Warranty
Under all circumstances this manual should be read attentively, before
installing and/or using the product. In no event shall Scantech-ID BV be
liable for any direct, indirect, special, consequential or incidental
damages arising out of the use or inability to use this documentation or
product, even if advised of the possibility of such damages. In particular,
Scantech-ID BV shall not be liable for any hardware, software, or data that
is stored or used with the product, including the cost of repairing,
replacing or recovering the above. Scantech-ID BV reserves the right to
change parts of the device at any time without preceding or direct
announcement to the client.
Scantech-ID BV reserves the right to revise this manual, and to make
changes in the contents without obligation to notify any person or entity
of the revision or change. A serial number appears on the product. Make
sure that this official registration number has not been removed. It should
be used whenever servicing by Scantech-ID BV or an authorized Scantech
dealer is necessary.
Due to Champtek’s / Scantech ID’s continuing product improvement programs, specifications
and features are subject to change without notice.
May 2011
Table of contents
Introduction .......................................... 1
Chapter 1 Product Safety ............................... 1
1.1 Safety & Caution ............................... 1
1.2 FCC Warning .................................... 3
1.3 Use of the VEGA ................................ 4
1.4 V-1020 Unpacking ............................... 5
1.5 mounting ....................................... 6
1.6 USB interface .................................. 7
1.7 Configuring .................................... 7
1.7.1
Changing Scanner Settings with
Programming Codes ................................. 7
1.7.2 Changing Scanner Settings with Utility Tool.8
Chapter 2 Operating Setting ............................ 9
2.1 RETURN TO DEFAULT .............................. 9
2.2 GET FIRMWARE VERSION ........................... 9
2.3 Interface Selection ........................... 10
2.4 Scanning Triggering ........................... 10
2.5 Trigger time out .............................. 12
2.6 Imager mode ................................... 13
2.7 Good Read Mode ................................ 14
2.8 Buzzer Beep Tone .............................. 14
2.8.1 Beep Tone Setup ............................ 14
2.8.2 Good Read Beeps ............................ 15
2.8.3 Beep Duration .............................. 15
2.8.4 Timing ..................................... 16
2.9 Good Read Duration ............................ 16
2.9.1 Good Read LED Duration ..................... 16
2.9.2 Error Beep................................. 17
2.9.3 Setup Beep................................. 17
2.10
RS-232 mode parameters .......................18
2.10.1
Baud rate ............................... 18
2.10.2
Data bits ............................... 18
2.10.3
Stop bits ............................... 19
2.10.4
Parity .................................. 19
2.10.5
Handshaking ............................. 19
2.11
Keyboard Wedge Mode Parameter ................20
2.11.1
Terminal Type ........................... 20
2.11.2
Capslock Detection ...................... 20
2.11.3
Upper/Lower Case ........................ 21
2.11.4
Send Character by ALT Method ............ 21
2.11.5
Select Numerical Pad .................... 21
2.11.6
Time out Between Characters ............. 22
2.11.7
Language Selection ...................... 23
2.12
Symbologies Selection ........................25
2.13
Multi code ...................................35
2.14
Postambles ...................................36
Appendixes ............................................37
A.DECIMAL VALUE TABLE ..............................37
B.ASCII Table ......................................38
C.Readable Symbologies .............................39
D.technical Specifications .........................40
E.Scan map .........................................41
Introduction
VEGA is a cutting-edge gun-type barcode scanner which is
designed specifically for retail market. To the brand
new series of VEGA, we add on more user-friendly
functions with detachable cable that makes it more
easily to be operated by the customers.
Speaking of the performance, this scanner supports
middle to long range operation. According to
specification, VEGA supports the reading depth up to 440
mm, scan rate is up to 200 scans / per second in linear
emulation or 56 images / per second in 2D mode.
The new VEGA scanner has most modern design with the
decorative cover display on the top of the scanner that
will enhance the looks of the checkout counter in the
retail market. This magnificent design allowed end-users
to display their product information or any relevant
commercial message in the cover display. This advanced
mechanical design truly creates a win-win solution for
both POS retail systems and consumers.
In short, VEGA is absolutely a high performance gun-type
scanner, which provides the customer with the most costeffective solution in the market. It is perfectly
suitable and definitely the best choice for any
retailers using POS environment.
The VEGA comes with the same top quality as all other
Scantech-ID products. So at a very competitive price the
same quality and performance of more expensive products
is available. Due to the high MTBF times of every
component a long and service free operation time is
secured.
The VEGA is available into interface types, RS232
interface, USB HID interface, Keyboard emulation
interface and also with Bluetooth technology, so there
is always a solution to connect the Vega to your POS
system.
Chapter 1 Product Safety
1.1
SAFETY & CAUTION
1. Please read the following safety statement carefully.
2. Please preserve this user manual for reference
sometime.
3. Before cleaning the VEGA, the users must cut off all
AC power. Do not use liquid or spray type of
detersive to clean the VEGA. Please use dampish
cotton cloth to clean the VEGA.
4. The outlet must set nearby the VEGA for connecting
power easily.
5. Keep the VEGA dry to avoid short circuit.
6. During installation you must fix the equipment at
solid table to avoid damage caused by falling.
7. Before inserting power please ensure the voltage is
healthy to the equipment.
8. For safety please tie wire well and don’t put
anything on the wire.
9. If you don’t use this equipment for long time,
please cut off the power to avoid damage from surge
power.
10.
Don’t spray any liquid on this scanner because
it may cause a fire or short circuit.
11.
Please do not open the equipment. For safety
only the qualified serviceman can open the equipment.
12.
If there are the following situations please
contact with the qualified serviceman to check this
equipment.
(a) The damage of wire or pin of power supply.
(b) Some Liquid infiltrate into the equipment.
(c) The equipment has been exposed to wet
environment.
(d) The equipment can’t work well.
(e) The equipment has any obvious damage, making the
VEGA working abnormally.
1
13.
Don’t storage the VEGA at the temperature lower
than -20°C (-4°F) or higher than +70°C (158°F) to
avoid any damage.
2
1.2
FCC WARNING
This equipment complies with the requirements in Part
15 of FCC.
Any operation must comply with the conditions below:
(a)
The equipment will not cause any severe
interference.
(b)
The equipment can avoid any interference from
environment.
Statement:
This product is classified as A class product.
In environment this product may cause some
interference. In this situation the user may
do something to avoid interference.
3
1.3 USE OF THE VEGA
The VEGA is very ergonomic and modern designed and very
user friendly. It can be connected to your POS or Host
system through a RS232 cable, KBW cable, USB cable.
To read a bar code, you simply press the red trigger
button and aim the beam to the bar code. But you need to
position the beam so that it falls across all bars in the
1D barcodes. You will hear one beep and the green LED
indicator will lights on after scan successfully.
The programming of the VEGA is very easy, you can set-up
the VEGA by scan all necessary programming codes one time
that meet applications, the settings are directly saved
permanently, and all settings can be disabled after scan
reset factory default.
Thanks to the power full decoding processor, the VEGA can
decode all major 1D codes.
4
1.4 V-1020 UNPACKING
Unpack the VEGA as follows:
1. Take the VEGA and its accessories out of the box.
2. Remove the packing material.
3. Check the packing list to make sure you have received
all of the items ordered.
Standard Shipment Package
(a)
(b)
(c)
(d)
VEGA Area Imager Handheld Bar code Scanner
Communication Cable
Power adaptor (optional)
User Manual
4. Visually inspect the VEGA and accessories for any
evidence of physical damage.
5. If anything is missing or appears to be damaged,
immediately contact your dealer.
ATTENTION
Store the packing material and boxes: it should
be used whenever the VEGA is transported for
servicing.
5
1.5 MOUNTING
Once you have unpacked all components, you can start
installing the VEGA.
Installation at VEGA is divided into different steps:
1. Connect the VEGA to the supplied interface cable
(RJ45 side).
2. Connect the VEGA interface cable to the POS system.
3. Connect the Power supply (used RS232 interface) to
Power cable jack.
4. Plug the power supply into the AC outlet.
RJ 45 10 pin
Connector
6
1.6 USB INTERFACE
As like all USB devices, before connecting the VEGA with
USB interface to your host system, the connect driver
must be installed correctly on your host system for VEGA
operate successful.
Please contact Scantech-ID Technical Support Department
if you need the VEGA USB driver or this USB driver can be
downloaded from the web site:
www.scantech-id.com/support/downloads
1.7 CONFIGURING
How to configure the VEGA:
The Barcode Programming Feature gives the possibility to
change the VEGA scanner settings with use programming
codes or with the Utility Tool.
1.7.1
Changing Scanner Settings with Programming Codes
You can set-up your VEGA by scan all necessary
programming codes for parameters that meet applications.
After these scans the VEGA is direct permanently saved.
To go back to the factory default settings, just scan
only programming code factory default.
In order to change the scanner settings please follow the
sequence below:
(a)
Power-up the scanner.
(b)
Change scanner settings by scanning any of the
programming code that meet applications.
At any moment you can stop your programming, and if
needed read programming code factory default setting for
set your scanner back to default.
7
1.7.2 Changing Scanner Settings with Utility Tool
Scantech-ID has setup this user manual with the most
common used programming codes, it could be possible that
you need more advanced settings to use the VEGA without
any problems into your application.
This tool can be used with the following operation
systems: Windows98, Windows2000, Windows XP and Windows
Vista.
This Utility Tool can be delivered on request. Please
contact Scantech-ID Technical Support Department. You can
download this USB driver from the Scantech-ID web site:
www.scantech-id.com/support/downloads
8
Chapter 2 Operating Setting
2.1 RETURN TO DEFAULT
Scan this programming code to set the scanner /Cradle
parameters to factory default:
Set the scanner to Factory Default
Reset all configuration parameters to their factory
default setting of the Scanner and Cradle. After this
reset you must select all required parameters that meet
applications.
2.2 GET FIRMWARE VERSION
Display the firmware version of the scanner, please scan
below barcode.
Engine Firmware Version
Scanner Decoder Firmware Version
9
2.3 INTERFACE Selection
<KEYBOARD MODE>
RS232 SERIAL MODE
<USB HID MODE>
USB COM PORT MODE
2.4 SCANNING TRIGGERING
<Level>
A reading session begins (lighting and decode processing
on) when beam is activated and stops when beam is
deactivated.
Continuous Scanning
When the scanner is turned on a continuous reading
session begins (lighting and decode processing on).
10
Pulse
A reading session begins when beam is activated and stays
on until a period of inactivity lasting the time
specified by the timeout.
After the timeout, the scan engine turns off.
Flashing
Flashing mode allows power up the lighting and decoding
are on (no need to activate the trigger line) and after a
period of inactivity lasting the time specified by the
trigger timeout, the scanner starts flashing, checking
for a bar code to be read.
When a bar code is detected, the lighting and decoding
automatically turn on and stay on until another period of
inactivity (timeout), after the timeout the scanner
starts flashing again.
Autostand
This mode allows you to switch from Flashing trigger mode
to Level trigger mode.
Autostand begins in flashing mode: At power up the
lighting and decoding are on (no need to activate the
trigger line) and after a period of inactivity lasting
the time specified by the trigger timeout, the scanner
starts flashing.
To switch to Level trigger mode activate the trigger line
(press the trigger).
11
When in Level trigger mode, after a period of inactivity
lasting the time specified by the trigger timeout, the
scanner switches back to flashing mode.
Toggle
This mode allows lighting and decoding toggle when the
trigger line is activated.
First trigger activation = lighting and decoding on,
Second trigger activation = lighting and decoding off.
Presentation
This mode allows power up lighting and decoding are on.
After a period of inactivity lasting the time specified
by the trigger timeout, the lighting turns off or is
dimmed. When a new bar code is presented the lighting and
decoding restart and stay on until another period
inactivity.
2.5 TRIGGER TIME OUT
<2 sec>
4 sec
6 sec
12
2.6 IMAGER MODE
You can set the best reading performance of your VEGA by
adjusting certain imager parameters. To choose the best
reading performance, depends on the environment, your
used application and type of barcodes.
 Area mode for decode 1D and 2D barcodes.
 Linear mode for decode 1D Barcodes.
Area mode allows you to set the position of the VEGA in
any direction regardless of the orientation of the
barcode, and perform a good read on 1D and 2D barcodes.
Linear mode allows you to increase your decoding speed
while scanning 1D barcodes. But, you need to position the
beam so that it falls across all bars in the 1D barcode.
Linear imager
<Area imager>
Area imager
Bright Environment
Area imager With
Reflective Surface
13
2.7 GOOD READ MODE
When active, the scan engine stops the reading session
after a successful decoding.
- NOTE: this parameter is NOT used with continuous and
continuous + flashing modes.
<Active>
Not Active
2.8 BUZZER BEEP TONE
2.8.1
Beep Tone Setup
<High>
Medium
Low
14
2.8.2
Good Read Beeps
<One Beep>
Two Beeps
None
2.8.3
Beep Duration
60 msec
<80 msec>
200 msec
Off
15
2.8.4
Timing
<During Transmission>
Before Transmission
After Transmission
2.9 GOOD READ DURATION
2.9.1
Good Read LED Duration
<80 msec>
0.5 sec
1 sec
Off
16
2.9.2
Error Beep
<On>
Off
2.9.3
Setup Beep
<On>
Off
17
2.10
RS-232 MODE PARAMETERS
2.10.1 Baud rate
1200
2400
4800
9600
<19200>
38400
2.10.2 Data bits
Data bits 7
<Data bits 8>
18
2.10.3 Stop bits
<Stop bits 1>
Stop bits 2
2.10.4 Parity
<None>
Even
Odd
2.10.5 Handshaking
RTS/CTS Enable
<RTS/CTS disable>
ACK/NAK Enable
19
<ACK/NAK Disable>
XON/XOFF Enable
<XON/XOFF Disable>
2.11 KEYBOARD WEDGE MODE PARAMETER
2.11.1 Terminal Type
<IBM PC/AT,PS/2>
IBM PC/XT
IBM PS/2 25, 30
2.11.2 Capslock Detection
Enable
<Disable>
20
2.11.3 Upper/Lower Case
<No change>
Upper Case
Lower Case
2.11.4 Send Character by ALT Method
Enable
<Disable>
2.11.5 Select Numerical Pad
ON
<OFF>
21
2.11.6 Time out Between Characters
<0 ms>
5 ms
10 ms
25 ms
50ms
100ms
22
2.11.7 Language Selection
<US English>
UK English
Italian
Spanish
French
German
Swedish
Switzerland
Hungarian
Japanese
23
Belgium
Portuguese
Denmark
Netherlands
Turkey
Reserved 1
24
2.12 SYMBOLOGIES SELECTION
Australian Post ON
<Australian Post OFF>
AZTEC ON
<AZTEC OFF>
BPO ON
<BPO OFF>
Canada Post ON
<Canada Post OFF>
CODABAR ON
25
<CODABAR OFF>
Codablock A ON
<Codablock A OFF>
Codablock F ON
<Codablock F OFF>
CODE 11 ON
<CODE 11 OFF>
<CODE 39 ON>
CODE 39 OFF
CODE 93 ON
26
<CODE 93 OFF>
<CODE 128 ON>
CODE 128 OFF
<GS1-128 ON>
GS1-128 OFF
<DATAMATRIX ON>
DATAMATRIX OFF
DataMatrix – Mirrored
labels activation On
<DataMatrix–Mirrored
labels activation off>
27
Dutch Post ON
<Dutch Post OFF>
<EAN-8 ON>
EAN-8 OFF
<EAN-13 ON>
EAN-13 OFF
<EAN 128 ON>
EAN 128 OFF
GS1 CC-A/B ON
28
<GS1 CC-A/B OFF>
GS1 CC-C ON
<GS1 CC-C OFF>
GS1 DataBar-Omni ON
<GS1 DataBar-Omni OFF>
GS1 DataBar-Limited ON
<GS1 DataBar-Limited
OFF>
GS1 DataBar-Expand ON
<GS1 DataBar-Expand OFF>
29
Infomail ON
<Infomail OFF>
Interleave 2 of 5 ON
<Interleave 2 of 5 OFF>
Japan Post ON
<Japan Post OFF>
Matrix 2 of 5 ON
<Matrix 2 of 5 OFF>
30
MaxiCode ON
<MaxiCode OFF>
MicroPDF417 ON
<MicroPDF417 OFF>
MSI ON
<MSI OFF>
<PDF417 ON>
PDF417 OFF
Planet ON
31
<Planet OFF>
PLESSEY ON
<PLESSEY OFF>
Postnet ON
<Postnet OFF>
QR Code ON
<QR Code OFF>
Standard 2 of 5 ON
<Standard 2 of 5
OFF>
32
Sweden Post ON
<Sweden Post OFF>
Telepen ON
<Telepen OFF>
TLC 39 ON
<TLC 39 OFF>
<UPC-A ON>
UPC-A OFF
<UPC-E ON>
UPC-E OFF
33
Note: This step does not include codes for all support
Barcode symbologies.
For a complete overview of support symbologies see
appendix.
If you need programming codes for symbologies which are
not available in this chapter, please contact Scantech-ID
Technical Support department or use VEGA utility tool.
34
2.13
MULTI CODE
The multicode function is used configure the scanner to
read a series of bar codes and then transmit them all at
once.
Follow these steps to setup the multicode function:
1. Activate the multicode function.
2. Select the number of bar codes to be included the
multicode.
Active
<Not Active>
Active Exclusive
Number of bar codes
compose: 2
Number of bar codes
compose: 3
Number of bar codes
compose: 4
Number of bar codes
compose: 5
35
Number of bar codes
compose: 6
2.14
POSTAMBLES
The scanner can be programmed to output Barcode data
according to the following format: [BAR CODE DATA]
[POSTAMBLE STRING]
Postamble None
<CR+LF >
CR
LF
TAB
SP
36
Appendixes
A.DECIMAL VALUE TABLE
0
1
2
3
4
5
6
7
8
9
37
B.ASCII TABLE
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
38
C.READABLE SYMBOLOGIES
1D Symbologies
Symbology
Codabar
Code 11
Code 39
Code 93 / 93i
Code 128
EAN 8 / EAN 13
EAN 128 / UCC
Default Enable
Off
Off
On
Off
On
On
On
GS1 DataBar (RSS)
Off
Interleaved 2 of 5
Industrial
ISBN
ISSN
Matrix
MSI Code
Plessey
Postal codes
Standard 2 of 5
Telepen
UPC A / UPC E
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Note
Omni, Expanded,
limited
On
2D Symbologies
Symbology
Default Enable
Aztec
Off
Datamatrix
On
PDF417
On
MicroPDF417
Off
Maxicode
Off
QR
Off
UCC/ EAN Composite
Off
39
Note
D.TECHNICAL SPECIFICATIONS
Physical Characteristics
Body Weight
Material
Connector
Dimension
Approx. 150 gm
ABS Plastic
RJ45C 10Pins
186.8 mm x 81.6 mm x 63.9 mm
Operational
Light source
Scan rate
Optical
resolution
Scan angle
Interface
Indicators
Visible Red light 650nm + 10nm
200 scans/sec auto adaptive in linear mode.
56 images/sec auto adaptive in 2D mode.
752 Horizontal x 480 Vertical pixels, 256
gray levels.
38° Horizontal, 25° Vertical
RS-232, USB, Keyboard
Green LED = good read
Electrical Characteristics
Operation Voltage
Current Operating
Current Standby
AC transformers
5 VDC ±5%
450 mA (max) @ 5 VDC
37 mA typical @ 5 VDC
5.2 VDC @ 650 mA / Input AC 100-240V
Environmental
Operating Temp.
0°C to 50°C (32°F to 122°F)
Storage Temp.
-20°C to 70°C (-4°F to 158°F)
Relative Humidity
0 to 95% non-condensing
Works in lighting conditions from 0
Ambient light
to 100,000 lux
Regulatory of Compliance
FCC
CE
40
E.SCAN MAP
Typical Reading Distances
VEGA Typical Reading Distance: These distances are
measured in an office environment (250 lux).
41
VEGA Typical Reading Distances (centimeters)
Symbology
Density
Code 39
0.125
0.20
0.25
0.50
1.00
0.33
0.19
0.25
0.38
0.16
0.25
0.38
UPC / EAN
Data matrix
PDF417
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
Minimum
Distance
7.2
cm
3.8
cm
3.4
cm
5.0
cm
8.0
cm
5.0
cm
6.3
cm
4.8
cm
*
6.2
cm
4.5
cm
4.0
cm
Maximum
Distance
13.1
cm
22.5
cm
27.0
cm
44.0
cm
83.0
cm
32.0
cm
17.2
cm
22.0
cm
29.0
cm
15.4
cm
23.0
cm
37.0
cm
VEGA Typical Reading Distances (inches)
mils
Minimum
Distance
2.8 Inch
Maximum
Distance
5.1 Inch
8
mils
1.5
Inch
8.8
10
mils
1.3
Inch
10.5 Inch
20
mils
2
Inch
17.2 Inch
40
mils
3.1
Inch
2.4
UPC / EAN
13
mils
2
Inch
12.5 Inch
Data matrix
7.5 mils
2.5
Inch
6.7
Inch
10
mils
1.9
Inch
8.6
Inch
15
mils
*
6.6 mils
2.4
Inch
6
Inch
10
mils
1.8
Inch
9
Inch
15
mils
1.6
Inch
14.4 Inch
Symbology
Density
Code 39
5
PDF417
Inch
Inch
11.3 Inch
*Minimum distance depends on symbology length and scan angle.
42
Scantech-ID BV
Vanadiumweg 22,
3812 PZ Amersfoort
The Netherlands.
Phone:
Fax:
+31 (0)33 469 84 00
+31 (0)33 465 06 15
E-mail: info@scantech-id.com
Internet: www.scantech-id.com
0145-VG80081
V01
43
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising