Extreme Networks | Summit X450-24x | Extreme Networks

Extreme Networks
Extreme Networks Data Sheet
Summit X450e Series
Summit X450e series switches are based on the
revolutionary ExtremeXOS core-class operating system
from Extreme Networks®. ExtremeXOS highly resilient,
modular operating system provides continuous uptime,
manageability and operational efficiency. Summit X450e provides high availability and performance
with its advanced traffic management capabilities to support
a large-scale rollout of a converged network that supports
devices such as IP telephones, wireless APs and other devices
that require power from a LAN connection. With low-latency
line-rate performance, Summit X450e-24p/48p supports the
802.3af standards-based Power over Ethernet (PoE) on
every port. Summit X450e supports hardware-based routing for both
IPv4 and IPv6 which helps provide investment protection
by allowing the rollout of IPv6 in your network now or in the future.
The flexible Summit X450e switches provide high-density
Gigabit Ethernet ports plus dedicated 40 Gbps high-speed
stacking ports and optional 10 Gigabit Ethernet ports in a
compact 1RU format, supporting a full range of Layer 2 to
Layer 4 functionalities on every port for high productivity.
Optional redundant power supplies are offered with each
switch to protect against power anomalies, providing a
continuous operational network.
Target Application
• PoE and non-PoE edge switches providing intelligent
10/100/1000BASE-T connectivity to the desktop in a network running ExtremeXOS from the core to the edge.
Summit® X450e—The industry’s first PoE and non-PoE edge
switches with the revolutionary modular operating system,
ExtremeXOS®.
Voice-Class Availability
• Modular ExtremeXOS operating system
• Ethernet Automatic Protection Switching (EAPS) resiliency protocol
• SummitStack™ and SummitStack-V—highly available,
high-speed stacking support
Designed for Converged
Network Applications
• High bandwidth, non-blocking architecture for
demanding edge applications
• Exceptional Quality of Service (QoS) with advanced traffic
management capabilities for converged applications
• Convergence-ready connectivity with Voice-over-IP
(VoIP) automatic provisioning • Efficient management to handle convergence-driven
network changes with Power over Gigabit Ethernet
Comprehensive Security
• User policy and host integrity enforcement and Identity
Management
• Universal Port dynamic security profile to provide fine
granular security policy in the network
• Threat detection and response instrumentation to react to
network intrusion with CLEAR-Flow Security Rules Engine
• Common Criteria EAL3+ Certification
Make Your Network Mobile
Extreme Networks Data Sheet: Summit X450e Series
Voice-Class Availability
Powered by the ExtremeXOS modular operating system, the Summit X450e switch supports process recovery and
application upgrades without the need for a system reboot. Summit X450e provides the high network availability
required for converged applications.
Modular Operating System for
Non-Stop Operation
Preemptive Multitasking and
Protected Memory
Summit X450e switches allow each of many applications—such
as Open Shortest Path First (OSPF) and Spanning Tree Protocol
(STP)—to run as separate Operating System (OS) processes
that are protected from each other. This drives increased
system integrity and inherently protects against Denial of
Service (DoS) attacks. Process Monitoring and Restart
The ExtremeXOS modular OS increases network availability
using process monitoring and restart. Each independent
OS process is monitored in real time. If a process becomes
unresponsive or stops running, it can be automatically
restarted.
Loadable Software Modules
The modular design of ExtremeXOS allows the upgrading of
individual software modules, should this be necessary, leading
to higher availability in the network (see Figure 1).
High Availability Network Protocols
Ethernet Automatic Protection
Switching (EAPS)
EAPS allows the IP network to provide the level of resiliency
and uptime that users expect from their traditional voice
network. EAPS is more adaptable than Spanning Tree or Rapid
Spanning Tree protocols and offers sub-second (less than 50
milliseconds) recovery that delivers consistent failover
regardless of the number of VLANs, network nodes or network
topology. Since EAPS allows the network to recover almost
transparently, VoIP calls will not drop and digital video feeds
will not freeze or pixelize in most situations.
Spanning Tree/Rapid Spanning
Tree Protocols
Summit X450e switches support Spanning Tree (802.1D), Per
VLAN Spanning Tree (PVST+), Rapid Spanning Tree (802.1w)
and Multiple Instances of Spanning Tree (802.1s) protocols for
Layer 2 resiliency. Software-Enhanced Availability
Software-enhanced availability allows users to remain
connected to the network even if part of the network
infrastructure is down. Summit X450e switches continuously
check for problems in the uplink connections using advanced
Layer 3 protocols such as OSPF, VRRP and Extreme Standby
Router Protocol™ (ESRP, supported in Layer 2 or Layer 3), and
dynamically route traffic around the problem.
Equal Cost Multipath Routing
Equal Cost Multipath (ECMP) routing allows uplinks to be load
balanced for performance and cost savings while also
supporting redundant failover. If an uplink fails, traffic is
automatically routed to the remaining uplinks and connectivity
is maintained. Link Aggregation (802.3ad)
Link aggregation allows trunking of up to eight links on a single
logical connection, for up to 20 gigabits per second (Gbps) of
redundant bandwidth per logical connection.
Multi-Switch LAG (M-LAG)
M-LAG can address bandwidth limitations and improve
network resiliency, in part by routing network traffic around
bottlenecks, reducing the risks of a single point of failure, and
allowing load balancing across multiple switches.
Voice-Grade Stacking with
SummitStack
Summit X450e offers dual stacking interfaces to provide
high-speed 40 Gbps stacking bandwidth. SummitStack
stacking architecture is designed to support converged services
such as VoIP and video by its highly available, rapid failover
capability with n-1 master redundancy, distributed Layer 2 and
Layer 3 switching, link aggregation across the stack and
distributed uplinks. SummitStack supports up to eight units in a
stack and the mixture of the units can be Summit X250e,
X450e, X450a, X460, X480, and X650 switches running the
same version of ExtremeXOS. It provides sub-second failover
for path failure and hitless master/backup failover along with
hitless protocol support such as OSPF graceful restart, PoE
configuration and Network Login user authentication.
2
Extreme Networks Data Sheet: Summit X450e Series
Voice-Class Availability
SummitStack-V Flexible Stacking
Over 10 Gigabit Ethernet
SummitStack-V enabled 10 GbE ports must be physically directconnected. SummitStack-V is compatible with Summit X450e,
X450a, X460, X480, X650, X670 and X670V switches running
the same version of ExtremeXOS. Summit X450e provides
chassis-like management and availability with its SummitStack
stacking technology (see Figure 2).
SummitStack-V capability utilizes 10 GbE ports as stacking
ports, enabling the use of standard cabling and optics
technologies used for 10 GbE such as XFP, SFP+, 10GBASE-T
and XENPAK. SummitStack-V provides long-distance
stacking connectivity of up to 40 km while reducing the
cable complexity of implementing a stacking solution.
1
3
Memory protected
processes under
real-time
scheduling that
cannot impact
each other nor
kernel
SSH-2
V1.3.2
BGP
SSH-2
V1.3.1
OSPF
Designed to allow
application
modules to be
upgraded during
runtime
Third
Party
Application
• Processes are monitored
and can be restarted or
other action taken if
necessary
• Hitless failover
infrastructure for dual
management systems
and stacking
2
Application
modules can be
added during
runtime
• Single management point for up to eight units
• 40 Gbps stacking
• Rapid Failover for converged applications
• Can mix Summit® X250e, Summit X450a/e series,
Summit X460, Summit X480 and Summit X650 series switches
VIM1-SummitStack
VIM1-SummitStack
ExtremeXOS
Kernel
Kernel Loadable
Module
5251-03
5027-04
Figure 1: ExtremeXOS Modular Design
Figure 2: SummitStack Stacking Architecture
3
Extreme Networks Data Sheet: Summit X450e Series
Designed for Converged Network Applications
Summit X450e provides a high bandwidth, non-blocking architecture with tri-speed copper Gigabit Ethernet ports in
PoE and non-PoE versions for demanding edge applications.
High Density Gigabit Ports with
Optional 10 Gigabit Uplinks
The Summit X450e series provides ideal performance and
functionalities for access switches. They eliminate the need
to funnel traffic through a low bandwidth gigabit trunk by
providing non-blocking 10 gigabit links to the core. As an
option module, Summit X450e provides a variety of choices
for 10 Gigabit Ethernet uplinks: dual port 10GBASE-T for UTP
connectivity, dual port SFP+ for fiber and passive copper
connectivity and dual port XFP.
Exceptional Policy-based QoS
PoE enabled Summit X450e switches provide eight hardware
queues per port to support granular traffic classification with
bandwidth allocation. 1024 centralized classifiers per 24 ports
can use information from Layers 1 through 4 to prioritize and
meter incoming packets at line-rate. When metering traffic, the
switches can drop out-of-spec traffic or flag it for later action.
To expedite upstream traffic handling, a packet’s classification
can be carried forward with Layer 2 (802.1p) and Layer 3
(DiffServ) markings. Summit X450e switches provide advanced
traffic management features that support the highest-quality
triple play of voice, video and data services. Efficient Management to Handle
Convergence-Driven Network
Changes
Universal Port—Voice-over-IP
Auto-Provisioning
PoE enabled Summit X450e switches set the stage for
convergence applications by allowing enterprises to add new
access devices in a plug-and-play fashion. Voice and wireless
services can be easily implemented without major network
upgrades. Summit X450e supports automatic provisioning
of VoIP using LLDP and event-based command scripting
capability. It allows dynamic configuration of voice VLANs and
QoS. This auto-configuration capability allows you to configure
VoIP phone settings such as voice VLAN settings, call server IP
address configuration, etc. This level of simplicity in managing
network changes can greatly reduce operating expenses.
Power over Gigabit Ethernet (PoE)
Deployments of IP Telephony depend on reliable, consistent
power from the Ethernet jack. Summit X450e-24p/48p is the
basis for a reliable LAN telephony infrastructure with fully
redundant 15.4 watts per port, and QoS and resiliency to match
the failover requirements for latency-sensitive services like VoIP
phones. With Summit X450e, deployment of powered LAN
devices is quick and easy with its support of the IEEE 802.3af
standard and full Class 3 power availability on all ports, backed
up 100% by the optional EPS-500 redundant power supply
(Summit X450e-24p). Summit X450e-48p can provide up to
370W of PoE power and can be increased up to 740W of PoE
power to support full 15.4W Class 3 devices on all 48 ports by
adding the External Power System (EPS-C and EPS-600LS). Voice-Grade Connections
Summit X450e supports a range of QoS technologies that
can prioritize and predictably handle high-priority traffic
policing or rate limiting on ingress, 802.1q tagging and DiffServ marking, and shaping on egress with eight queues per port.
The Extreme Networks tradition of building products with low
latency and jitter continues with Summit X450e.
Universal Connectivity
Summit X450e-24p/48p switches offer universal connectivity
with high-performance gigabit to the desktop, PoE and
wireless support from every RJ-45 port. Installing universal
services ports everywhere for data and device power greatly
simplifies installations and moves, and helps to future-proof
your edge network. Summit X450e-24p/48p provides universal
attachment at any desktop Ethernet speed, and any power
level from none to full 15.4 Watts.
Comprehensive Network Management
Summit X450e switches support comprehensive network
management through Command Line Interface (CLI), SNMP v1,
v2c, v3, and an embedded XML-based Web User Interface,
ExtremeXOS ScreenPlay™. With a variety of management
options and consistency across other Extreme Networks
modular and stackable switches, Summit X450e series switches
provide ease of management for demanding converged
applications. 4
Extreme Networks Data Sheet: Summit X450e Series
Designed for Converged Network Applications
Extreme Networks has developed tools that simplify and help
in efficiently managing your network. Ridgeline™ network and
service management provides fault, configuration, accounting,
performance and security functions, allowing more effective
management of Extreme Networks products, solutions and
third-party devices, in a converged network.
deployment. An optional ExtremeXOS Advanced Edge license
extends the feature set to include other important edge
functions such as:
• Edge OSPF for much greater extensibility than RIP can
provide
• Edge PIM sparse modes for routing of multicast streams
Advanced Routing Capabilities for the Edge
• Policy-based routing
Summit X450e switches support advanced protocols for an
efficient and productive network. Summit X450e switches
provide static and RIP routing for simple IPv4 and IPv6 Layer 3
• Virtual Router Redundancy Protocol (VRRP) to provide
routing redundancy
NETWORK
CORE
4
1
5
LLDP / LLDP-MED
3
2
IP Phone
1
Administrator defines Universal Port policy for IP phones.
2
Phone is connected.
3
Phone sends vendor, model, detailed power requirements, etc.
to switch.
4
Switch automatically configures VLAN, QoS, and PoE on the port.
5
Switch pushes VLAN, QoS, call server details, etc. to the phone.
5044-03
Figure 3: Universal Port Voice-over-IP Provisioning
5
Extreme Networks Data Sheet: Summit X450e Series
Comprehensive Security Management
Implementing a secure network means providing protection at the network perimeter as well as the core. Summit X450e
uses advanced security functions in protecting your network from known or potential threats. Extreme Networks
security offerings encompass three key areas: user and host integrity, threat detection and response, and hardened
network infrastructure. Furthermore, with policy-based routing, measures can be taken to provide confidentiality of
selective data in transit between internal network nodes.
User Authentication and Host
Integrity Checking
Network Login and Dynamic Security Profile
Network Login capability implemented in ExtremeXOS enforces
user admission and usage policies. Summit X450e series
switches support a comprehensive range of Network Login
options by providing an 802.1x agent-based approach, a
Web-based (agent-less) login capability for guests, and a
MAC-based authentication model for devices. With these modes
of Network Login, only authorized users and devices can
connect to the network and be assigned to the appropriate
VLAN. The Universal Port scripting framework available in
Summit X450e lets you implement Dynamic Security Profiles,
which in sync with Network Login allows you to implement
fine-grained and robust security policies. Upon authentication,
the switch can load dynamic ACLs/QoS profiles for a user or
group of users, to deny/allow the access to the application
servers or segments within the network.
Multiple Supplicant Support
Shared ports represent a potential vulnerability in a network.
Multiple supplicant capability on a switch allows it to uniquely
authenticate and apply the appropriate policies and VLANs for
each user or device on a shared port.
Multiple supplicant support secures IP Telephony and wireless
access. Converged network designs often involve the use of
shared ports.
Media Access Control (MAC) Lockdown
MAC lockdown secures printers, wireless APs and servers. The
MAC address security/lockdown feature allows Summit X450e
to block access to any Ethernet port when the MAC address of
a station attempting to access the port is different from the
configured MAC address. This feature is used to “lock down” any
device to a specific port.
Host Integrity Checking
Host integrity checking helps keep infected or non-compliant
machines off the network. Summit X450e series switches
support a host integrity or endpoint integrity solution that is
based on the model from the Trusted Computing Group.
Identity Manager
Identity Manager allows network managers to track users who
access their network. User identity is captured based on
NetLogin authentication, LLDP discovery and Kerberos
snooping. ExtremeXOS uses the information to then report on
the MAC, VLAN, computer hostname, and port location of the
user. Further, Identity Manager can create both roles and policies,
and then bind them together to create role-based profiles based
on organizational structure or other logical groupings, and apply
them across multiple users to allow appropriate access to
network resources. In addition, support for Wide Key ACLs
further improves security by going beyond the typical source/
destination and MAC address as identification criteria access
mechanism to provide filtering capabilities.
Network Intrusion Detection and
Response
CLEAR-Flow Security Rules Engine
CLEAR-Flow Security Rules Engine provides first order threat
detection and mitigation, and mirrors traffic to appliances for
further analysis of suspicious traffic in the network.
Hardware-based sFlow Sampling
sFlow is a sampling technology that provides the ability to
continuously monitor application-level traffic flows on all
interfaces simultaneously. The sFlow agent is a software process
that runs on Summit X450e and packages data into sFlow
datagrams that are sent over the network to an sFlow collector.
The collector gives an up-to-the-minute view of traffic across the entire network, providing the ability to troubleshoot network problems, control congestion and detect network
security threats.
Port Mirroring
To allow threat detection and prevention, Summit X450e
switches support many-to-one and one-to-many port mirroring.
This allows the mirroring of traffic to an external network
appliance such as an intrusion detection device for trend analysis
or for utilization by a network administrator for diagnostic
purposes. Port mirroring can also be enabled across switches in
a stack. 6
Extreme Networks Data Sheet: Summit X450e Series
Comprehensive Security Management
Line-Rate ACLs
ACLs are one of the most powerful components used in
controlling network resource utilization as well as protecting the
network. Summit X450e switches support 1,024 centralized ACLs
per 24-port block based on Layer 2, 3 or 4 header information
such as the MAC or IP source/destination address. ACLs are used for filtering the traffic, as well as classifying the traffic flow
to control bandwidth, priority, mirroring, and policy-based
routing/switching. Denial of Service Protection
Summit X450e switches effectively handle DoS attacks. If the
switch detects an unusually large number of packets in the CPU
input queue, it will assemble ACLs that automatically stop these
packets from reaching the CPU. After a period of time, these
ACLs are removed, and reinstalled if the attack continues.
ASIC-based LPM routing eliminates the need for control plane
software to learn new flows, allowing more network resilience
against DoS attacks.
Secure Management
To prevent management data from being intercepted or altered
by unauthorized access, Summit X450e switches support SSH2,
SCP and SNMPv3 protocols. The MD5 hash algorithm used in
authentication prevents attackers from tampering with valid data
during routing sessions.
7
Extreme Networks Data Sheet: Summit X450e Series
Target Application
PoE and Non-PoE Edge Switches for
High-Bandwidth Applications
With line-rate performance and low latency, all
Summit X450e switches extend the benefits of
the ExtremeXOS operating system to the network
edge. This uniformity provides consistent quality
and performance throughout your converged
network while reducing operational inefficiencies.
The Summit X450e-24p/48p PoE edge switches
connect wireless devices, LAN telephony, PDAs
and other equipment without compromising
security, scalability, availability, mobility or
management. The Summit X450e-24t/48t
non-PoE edge switches provide the same
uncompromising service when PoE is not
a requirement.
NETWORK
CORE
Summit® X450e-24p/48p
Summit X450e-24t/48t
`
`
DEF
2ABC
1-@
5ABC
4GHI
7PQRS
*
U
8TUV
0+|
3
MNO
6
WXYZ
9
#+|
5045-04
Supported Protocols and Standards
A list of supported protocols and standards is available
on the Extreme Networks website at:
http://www.extremenetworks.com/go/xos
8
Extreme Networks Data Sheet: Summit X450e Series
Technical Specifications
Summit X450e-24p/
Summit X450e-24p-TAA/
Summit X450e-24t
General Specifications
Performance
• 128 Gbps switch fabric bandwidth
• 95.2 Mpps frame forwarding rate
• 9,216 Byte maximum packet size (Jumbo Frame)
• 128 load sharing trunks, up to 8 members per trunk
• 8 QoS queues/port
• 4,094 VLANs (Port, Protocol, IEEE 802.1Q)
• 1,024 centralized ACL rules per switch
Forwarding Tables
• Layer 2/MAC Addresses: 8K
• IPv4 LPM Entries: 512 • IPv6 LPM Entries: 256
Rate Limiting
• Ingress bandwidth policing/rate limiting per flow
• Egress bandwidth rate shaping per egress
queue and per port
• Rate Limiting Granularity: 64Kbps
• Available Rate Limiters: 1,024 per switch
Indicators
• Per port status LED including power status
• System Status LEDs: management, fan and power
Ports
• 24 ports 10/100/1000BASE-T PoE with
auto-speed and auto-polarity (Summit X450e-24p/
Summit X450e-24p-TAA)
• 24 ports 10/100/1000BASE-T with
auto-speed and auto-polarity (Summit X450e-24t)
• 4 ports SFP (shared PHY with 4
10/100/1000BASE-T ports)
• 1 port Serial (control port)
• 1 10/100BASE-T out-of-band management
port
• Per port status LED including power status
Option Slot
• Slot for XGM2 dual 10 gigabit option module
External Power Supply Support
• EPS-500
Physical Specifications
Dimensions
• Height: 1.73 Inches/4.4 Cm
• Width: 17.35 Inches/44.1 Cm
• Depth: 15.3 Inches/38.7 Cm
• Weight: 14 lbs/6.35 Kg (Summit X450e-24p/
Summit X450e-24p-TAA)
• Weight: 13.75 lbs/6.24 Kg (Summit X450e-24t)
Operating Specifications
Temperature
• Operating Temperature Range: 0° C to 40°
C (32° F to 104° F)
• Operating Humidity: 10% to 93% relative
humidity, non-condensing
• Operational Shock (Half Sine): 30 m/s2 (3g),
11ms, 60 Shocks
• Operational Random Vibration: 3-500 MHz @ 1.5g rms
Storage & Transportation Conditions
(Packaged)
• Transportation Temperature: -40° C to 70° C
(- 40° F to 158° F)
• Storage and Transportation Humidity: 10% to 95% RH, non-condensing
• Packaged Shock (Half Sine): 180 m/s2 (18g),
6ms, 600 shocks
• Packaged Sine Vibration: 5 – 62 Hz @ Velocity 5mm/s, 62-500 Hz @ 0.2 G
• Packaged Random Vibration: 5 – 20 Hz @ 1.0 ASD w/-3dB/oct. from
20-200 Hz
• 14 drops min on sides & corners @ 42”
(<15kg box)
Power & Acoustic Sound
All Summit X450e 24-port Models
• Voltage Input Range: 90 – 264V
• Maximum In-Rush Current: 30A @115V/60A@ 280V
• Efficiency: 80% with 60% – 100% load
• Line Frequency Range: 47 – 63 Hz
• Nominal Frequency Range: 50 – 60 Hz
• Power Supply Input Socket: IEC 320 C14
• Power Cord Input Plug: IEC 320 C13
• Sound Power in accordance with EN 300
753 (10-1997)
• Sound Power: 62 dBA per ISO 7779
• Declared Sound Power: 6.4 belsA per ISO 7779 & ISO 9296
• Bystander Sound Pressure in accordance
with NEBS GR-63 Issue 2
• Bystander Sound Pressure: 54 dBA right
side @ .6m
Summit X450e-24p/
Summit X450e-24p-TAA
• Nominal Input Ratings: 100 – 240V,
50/60Hz, 5.25A
• Nominal Input Current: 4.25A @ 115V~ (lowline) 2.0A @ 230V~ (highline)
• Heat Dissipation (with PoE full load): 120W (410 BTU/hr)
• Power Consumption (with PoE full load):
488W (1,665 BTU/hr)
• Heat Dissipation (without PoE): 54W (184 BTU/hr)
• Power Consumption (without PoE): 54W (184 BTU/hr)
Summit X450e-24t
• Nominal Input Ratings: 100 – 240V,
50/60Hz, 1A
• Nominal Input Current: 1.5A @ 115V~ (lowline)
0.75A @ 230V~ (highline)
• Heat Dissipation: 54W (184 BTU/hr)
• Power Consumption: 54W (184 BTU/hr)
9
Extreme Networks Data Sheet: Summit X450e Series
Technical Specifications
Summit X450e-48p/
SummitX450e-48p-TAA/
Summit X450e-48t
General Specifications
Performance
• 256 Gbps switch fabric bandwidth
• 130.9 Mpps frame forwarding rate
• 9,216 Byte maximum packet size (Jumbo Frame)
• 128 load sharing trunks, up to 8 members per trunk
• 8 QoS queues/port
• 4,094 VLANs (Port, Protocol, IEEE 802.1Q)
• 1,024 centralized ACL rules per 24-ports
Forwarding Tables
• Layer 2/MAC Addresses: 8K
• IPv4 LPM Entries: 512 • IPv6 LPM Entries: 256
Rate Limiting
• Ingress bandwidth policing/rate limiting per flow
• Egress bandwidth rate shaping per egress
queue and per port
• Rate Limiting Granularity: 64Kbps
• Available Rate Limiters: 1,024 per 24-ports
Indicators
• Per port status LED including power status
• System Status LEDs: management, fan and power
Ports
• 48 ports 10/100/1000BASE-T PoE with
auto-speed and auto-polarity (Summit X450e-48p/
Summit X450e-48p-TAA)
• 48 ports 10/100/1000BASE-T with
auto-speed and auto-polarity (Summit X450e-48t)
• 4 ports SFP (shared PHY with 4 10/100/1000BASE-T ports)
• 1 port Serial (control port)
• 1 10/100BASE-T out-of-band management
port
Option Slot
• Slot for XGM2 dual 10 gigabit option module
External Power Supply Support
• EPS-C with EPS-600LS (Summit X450e-48p)
• EPS-500 (Summit X450e-48t)
Physical Specifications
Dimensions
• Height: 1.73 Inches/4.4 Cm
• Width: 17.35 Inches/44.1 Cm
• Depth: 17.0 Inches/43.2 Cm
• Weight: 16.25 lbs/7.4 Kg (Summit X450e-48p/
Summit X450e-48p-TAA)
• Weight: 15.75 lbs/7.14 Kg (Summit X450e-48t)
Operating Specifications
Temperature
• Operating Temperature Range: 0° C to 40° C (32° F to 104° F)
• Operating Humidity: 10% to 93% relative
humidity, non-condensing
• Operational Shock (Half Sine): 30 m/s2 (3g),
11ms, 60 Shocks
• Operational Random Vibration: 3-500 MHz @ 1.5g rms
Storage & Transportation Conditions
(Packaged)
• Transportation Temperature: -40° C to 70° C
(- 40° F to 158° F)
• Storage and Transportation Humidity: 10% to 95% RH, non-condensing
• Packaged Shock (Half Sine): 180 m/s2 (18g),
6ms, 600 shocks
• Packaged Sine Vibration: 5 – 62 Hz @ Velocity 5mm/s, 62 – 500 Hz @ 0.2 G
• Packaged Random Vibration: 5 – 20 Hz @ 1.0 ASD w/-3dB/oct. from 20 – 200 Hz
• 14 drops min on sides & corners @ 42”
(<15kg box)
Power & Acoustic Sound
All Summit X450e 48-port Models
• Voltage Input Range: 90 – 264V
• Nominal Input Ratings: 100~240V, 50/60 Hz,
6.0A
• Maximum In-Rush Current: 30A @115V/60A@ 230V
• Efficiency: 80% with 60% – 100% load
• Line Frequency Range: 47 – 63 Hz
• Nominal Frequency Range: 50 – 60 Hz
• Power Supply Input Socket: IEC 320 C14
• Power Cord Input Plug: IEC 320 C13
• Sound Power in accordance with EN 300
753 (10-1997)
• Sound Power: 62 dBA per ISO 7779
• Declared Sound Power: 6.4 belsA per
ISO 7779 & ISO 9296
• Bystander Sound Pressure in accordance
with NEBS GR-63 Issue 2
• Bystander Sound Pressure: 54 dBA right
side @ .6m
Summit X450e-48p/
Summit X450e-48p-TAA
• Nominal Input Current: 5.25A @ 100V~ (lowline) 2.5A @ 230V~ (highline)
• Heat Dissipation (with PoE full load): 180W (614 BTU/hr)
• Power Consumption (with PoE full load):
507W (1,730 BTU/hr)
• Heat Dissipation (without PoE): 73W (250 BTU/hr)
• Power Consumption (without PoE): 73W (250 BTU/hr)
Summit X450e-48t
• Nominal Input Current: 2.25A @ 115V~ (lowline) 1.0A @ 230V~ (highline)
• Heat Dissipation: 73W (250 BTU/hr)
• Power Consumption: 73W (250 BTU/hr)
10
Extreme Networks Data Sheet: Summit X450e Series
Technical Specifications
Summit X450e
Series – All
Regulatory/Safety Standards
North American Safety of ITE
• UL 60950-1 1st Ed., Listed Device (U.S.)
• CSA 22.2#60950-1-03 1st Ed. (Canada)
• Complies with FCC 21CFR 1040.10 (U.S. Laser Safety)
• CDRH Letter of Approval (U.S. FDA Approval)
European Safety of ITE
•
•
•
•
EN60950-1:2001+A11
EN 60825-1+A2:2001 (Lasers Safety)
TUV-R GS Mark by German Notified Body
2006/95/EC Low Voltage Directive
International Safety of ITE
• CB Report & Certificate per IEC 609501:2001 + National Differences
• AS/NZS 60950-1 (Australia/New Zealand)
EMI/EMC Standards
North America EMC for ITE
• FCC CFR 47 part 15 Class A (U.S.)
• ICES-003 Class A (Canada)
European EMC Standards
• EN 55022:2003 Class A
• EN 55024:A2-2003 Class A includes IEC 61000-4-2, 3, 4, 5, 6, 11
• EN 61000-3-2,8-2000(Harmonics)
• EN 61000-3-3 1995+A1:2001(Flicker)
• ETSI EN 300 386 v1.3.3, 2005-04 (EMC Telecommunications)
• 2004/108/EC EMC Directive
International EMC Certifications
• CISPR 22: 2005, Class A (International Emissions)
• CISPR 24:A2:2003 Class A (International Immunity)
• IEC/EN 61000-4-2:2001 Electrostatic
Discharge, 8kV Contact, 15 kV Air, Criteria A
• EC/EN 61000-4-3:2002 Radiated Immunity
10V/m, Criteria A
• EC/EN 61000-4-4:2004 Transient Burst, 1 kV, Criteria A
• IEC/EN 61000-4-5:2001 Surge, 2 kV L-L, 2 kV L-G, Level 3, Criteria A
• IEC/EN 61000-4-6:2004 Conducted
Immunity, 0.15-80 MHz, 10V/m unmod. RMS,
Criteria A
• EC/EN 61000-4-11:2004 Power Dips &
Interruptions, >30%, 25 periods, Criteria C
Country Specific
• VCCI Class A (Japan Emissions)
• ACMA (C-Tick) (Australia Emissions)
• KCC Mark EMC Approval (Korea)
Environmental Standards
• EN/ETSI 300 019-2-1 v2.1.2 (2000-09) –
Class 1.2 Storage
• EN/ETSI 300 019-2-2 v2.1.2 (1999-09) –
Class 2.3 Transportation
• EN/ETSI 300 019-2-3 v2.1.2 (2003-04) –
Class 3.1e Operational
• EN/ETSI 300 753 (1997-10) – Acoustic Noise
• ASTM D3580 Random Vibration
Unpackaged 1.5G
Security
• Common Criteria EAL3+ Certification
Warranty
• Ltd. Lifetime with express Advanced
Hardware Replacement (for products
shipped from Extreme Networks on or after
June 29, 2009)
• For warranty details, visit www.extremenetworks.com/go/warranty
Telecom Standards
• EN/ETSI 300 386:2001 (EMC Telecommunications)
• EN/ETSI 300 019 (Environmental for Telecommunications)
IEEE 802.3 Media Access
Standards
• IEEE 802.3ab 1000BASE-T
• IEEE 802.3z 1000BASE-X
• IEEE 802.3ae 10GBASE-X
• IEEE 802.3an 10GBASE-T
11
Extreme Networks Data Sheet: Summit X450e Series
Accessories
Summit X450e Series Redundant PSUs
EPS-500
EPS-500 is the redundant AC Power Supply for higher
power consuming AC PSU-based switches including
Power-over-Ethernet enabled switches. EPS-500 is one
rack unit height and works in standalone. EPS-500 can be
rack mounted in a regular 19 inch rack system. EPS-500
comes with a DC output cable to connect between the
Summit switch and EPS-500.
Front View
Rear View
EPS-600LS and EPS-C
EPS-600LS is a power module that works with the EPS-C
External Power System Chassis. EPS-C has three slots for
EPS-600LS and one DC output to connect to high-density
PoE Summit switches. Depending upon the number of
EPS-600LS installed in EPS-C, it can provide 1) Redundant
configuration for up to 370 watts of PoE power with one
EPS-600LS installed; 2) Non-Redundant configuration
for up to 740 watts of PoE power with two EPS-600LS
installed; and 3) Redundant configuration for up to 740
watts of PoE power with three EPS-600LS installed. EPS-C
comes with a DC output cable to connect between the
Summit switch and EPS-C with EPS-600LS installed.
Front View
Rear View
Configured
View
Redundant PSU Compatibility Matrix
Summit Switch Models
Summit Switch
Part Number(s)
External Redundant PSU options
Summit X450e-24t
16141
EPS-500 external power supply (10911)
Summit X450e-24p
16142
EPS-500 external power supply (10911)
Summit X450e-48t
16147
EPS-500 external power supply (10911)
Summit X450e-48p
16148
EPS-C (10912) and EPS-600LS (10913)
Summit X450e-48p-TAA
16150
EPS-C (10912) and EPS-600LS (10913)
12
Extreme Networks Data Sheet: Summit X450e Series
Accessories
Power Supply Units
EPS-500
Power
Dimensions and Weight
• Voltage Input Range: 90 – 264V
• Nominal Input Ratings: 100 – 240V~, 50 – 60Hz, 10A
• Line Frequency Range: 47 – 63 Hz
• Maximum Input Current: 5.75A at 115 VAC,
2.80A at 230 VAC
• Maximum Inrush Current: 30A at 115 VAC,
60A at 230 VAC
EPS-500
• Height: 1.73 Inches/4.4 Cm
• Width: 17.4 Inches/44 Cm
• Depth: 7.6 Inches/19.3 Cm
• Weight: 10.8 Lbs/4.9 Kg • Output: -50 VDC, 7.5A max, 375 Watts 12
VDC, 7.5A max, 90 Watts
• Power Supply Input Socket: IEC 320 C14
• Power Cord Input Plug: IEC 320 C13
• Heat Dissipation: 158W (539.1 BTU/h)
• Power Consumption: 659W (2448.6 BTU/h) EPS-C/EPS-600LS
Dimensions and Weight
Power – EPS-600LS
• Voltage Input Range: 90 – 264 V
• Nominal Input Voltage/Hz: 115V~/60Hz &
230V~/50Hz, 10.0A
• Line Frequency Range: 47 – 63 Hz
• Maximum Input Current Rating: 7.0A at 115
VAC, 3.5A at 230 VAC
• Maximum Inrush Current: 30A at 115 VAC,
60A at 230 VAC
• Power Supply Input Socket: IEC 320 C14
• Power Cord Input Plug: IEC 320 C13
• Heat Dissipation: 219W (747.7BTU/h)
• Power Consumption: 801W (2733.1BTU/h)
EPS-C
• Height: 1.73 Inches/4.4 Cm
• Width: 17.32 Inches/44.0 Cm
• Depth: 11.81 Inches/30.0 Cm
• Weight: 7.17 Lbs/3.16 Kg EPS-600LS
• Height: 1.69 Inches/4.3 Cm
• Width: 4.61 Inches/11.7 Cm
• Depth: 11.81 Inches/30.9 Cm
• Weight: 3.74 Lbs/1.70 Kg
External Power Supply Chassis System –
EPS-C with three EPS-600LS installed
• Heat Dissipation: 360W (1228.4BTU/h)
• Power Consumption: 1620W (5527.7BTU/h)
XGM2 Dual 10 Gigabit Ethernet Modules
XGM2 Dual 10 Gigabit
Ethernet Module
XGM2-2bt
XGM2-2sf
XGM2-2xf
XGM2-2xn
Interface Type
10GBASE-T
SFP+
XFP
XENPAK
UTP
SFP+ Passive Copper
SFP+ Optics
XFP Optics
XENPAK Optics
100 meters (Category 6a)
55 meters (Category 6 and 5e)
1-10 meters (Passive Copper)
300m-40km
300m-80km
300m-80km
N/A
10GBASE-SR/LR/ER/LRM
10GBASE-SR/LR/ER/ZR
10GBASE-SR/LR/ER/ZR/LW
Supported Media
Distance
Optics Support
13
Extreme Networks Data Sheet: Summit X450e Series
Ordering Information
Part
Number
Name
Description
16141
Summit X450e-24t
24 10/100/1000BASE-T; 4 unpopulated 1000BASE-X SFP ports (shared); slot for XGM2 10
Gigabit Ethernet module; 2 SummitStack stacking ports; 1 AC PSU; connector for EPS-500
external redundant PSU; ExtremeXOS Edge license
16142
Summit X450e-24p
24 10/100/1000BASE-T Power over Ethernet; 4 unpopulated 1000BASE-X SFP ports
(shared); slot for XGM2 10 Gigabit Ethernet module; 2 SummitStack stacking ports; 1 AC
PSU; connector for EPS-500 external redundant PSU; ExtremeXOS Edge license
16142T
Summit X450e-24p-TAA
U.S. Federal TAA; 24 10/100/1000BASE-T Power over Ethernet; 4 unpopulated
1000BASE-X SFP ports; dual 10G option slot; 2 dedicated10G stacking ports; AC PSU;
connector for EPS-500 external redundant PSU; ExtremeXOS Edge license
16147
Summit X450e-48t
48 10/100/1000BASE-T; 4 unpopulated 1000BASE-X SFP ports (shared); slot for XGM2 10
Gigabit Ethernet module; 2 SummitStack stacking ports; 1 AC PSU; connector for EPS-500
external redundant PSU; ExtremeXOS Edge license
16148
Summit X450e-48p
48 10/100/1000BASE-T with PoE; 4 unpopulated 1000BASE-X SFP ports (shared); slot for
XGM2 10 Gigabit Ethernet module; 2 SummitStack stacking ports; 1 AC PSU; ExtremeXOS
Edge license; connector for EPS-C external power system chassis (Requires EPS-600LS)
16148T
Summit X450e-48p-TAA
U.S. Federal TAA; 48 10/100/1000BASE-T with PoE; 4 unpopulated SFP ports; option slot
for 10 Gigabit option card XGM2; 2 SummitStack stacking ports; 1 AC PSU; ExtremeXOS
Edge license; connector for EPS-C external power system chassis (Requires EPS-600-LS)
16171
Summit X450 Advanced Edge License
ExtremeXOS Advanced Edge License for Summit X450e series switches
16112
XGM2-2xf
Option Card, Two Unpopulated 10 Gigabit XFP Slots, compatible with Summit X450e, and
Summit X450a
16113
XGM2-2xn
Option Card, Two Unpopulated 10 Gigabit XENPAK Slots, compatible with Summit X450e
and Summit X450a
16114
XGM2-2sf
Option Card, Two Unpopulated 10 Gigabit SFP+ Slots, compatible with Summit X350,
Summit X450e and Summit X450a
16115
XGM2-2bt
Option Card, two 10GBASE-T ports, compatible with Summit X350, Summit X450e and
Summit X450a
10911
EPS-5001
External Power Supply Unit 500 Watts, Power cord ordered separately
10912
EPS-C2
External Power Supply Unit, Power cord ordered separately, Accepts up to three EPS-600LS Power Modules
10913
EPS-600LS
External Power System Power Module for EPS-C, 600 Watts
10110
SR XENPAK
10GBASE-SR XENPAK Transceiver, 850 nm, up to 300 m on Multimode Fiber, SC Connector
10111
LR XENPAK
10GBASE-LR XENPAK Transceiver, 1310 nm, up to 10 km on Single-mode Fiber, SC Connector
10112
ER XENPAK
10GBASE-ER XENPAK Transceiver, 1550 nm, up to 40 km on Single-mode Fiber, SC Connector
10113
ZR XENPAK
10GBASE-ZR XENPAK Transceiver, 1550 nm, up to 80 km on Single-mode Fiber, SC Connector
10114
LX4 XENPAK
10GBASE-LX4 XENPAK Transceiver, 1310 nm, up to 300 m on Multi-mode Fiber and up to
10 km on a Single-mode Fiber, SC Connector
10121
SR XFP
10GBASE-SR XFP Transceiver, 850nm, up to 300m on Multimode Fiber, LC Connector
10122
LR XFP
10GBASE-LR XFP Transceiver, 1310nm, up to 10km on Single-mode Fiber, LC Connector
1
Compatible with Summit X450e-24t, X450e-48t, and X450e-24p
2
Compatible with Summit X450e-48p and Summit X450e-48p-TAA
14
Extreme Networks Data Sheet: Summit X450e Series
Ordering Information
3
Part
Number
Name
Description
10124
ER XFP
10GBASE-ER XFP Transceiver, 1550nm, up to 40km on Single-mode Fiber, LC Connector
10125
ZR XFP
10GBASE-ZR XFP Transceiver, 1550nm, up to 80km on Single-mode Fiber, LC Connector
10301
10GBASE-SR SFP+
10GBASE-SR SFP+, 850nm, LC Connector, transmission length of up to 300m on MMF
10302
10GBASE-LR SFP+
10GBASE-LR SFP+, 1310nm, LC Connector, transmission length of up to 10km on SMF
10303
SFP+ LRM Module
10 Gigabit Ethernet SFP+ module, 1310nm, legacy MMF 220m link, LC connector
10309
10GBASE-ER SFP+
10GBASE-ER SFP+, 1550nm, LC connector, transmission length of up to 40km on SMF
10304
10GBASE-CR SFP+ 1m
10GBASE-ER XFP Transceiver, 1550nm up to 40km on Single-mode Fiber, LC Connector
10305
10GBASE-CR SFP+ 3m
10GBASE-CR SFP+ pre-terminated twin-ax copper cable with link lengths of 3m
10306
10GBASE-CR SFP+ 5m
10GBASE-CR SFP+ pre-terminated twin-ax copper cable with link lengths of 5m
10307
10GBASE-CR SFP+ 10m
10GBASE-CR SFP+ pre-terminated twin-ax copper cable with link lengths of 10m
10051
SX SFP
1000BASE-SX SFP, 1000BASE-SX, LC Connector
10052
LX SFP
1000BASE-LX SFP, 1000BASE-LX, LC Connector
10053
ZX SFP
1000BASE-ZX SFP, Extra Long Distance SMF 70 km/21 dB Budget, LC Connector
10056
1000BX SFP BX-D
1000BASE-BX-D SFP, SMF (1490 nm TX/1310 nm RX Wavelength)
10057
1000BX SFP BX-U
10GBASE-CR SFP+ pre-terminated twin-ax copper cable with link lengths of 5m
16106
Stacking Cable, 0.5M
SummitStack/UniStack™ Stacking Cable, 0.5M
16107
Stacking Cable, 1.5M
SummitStack/UniStack Stacking Cable, 1.5M
16108
Stacking Cable, 3.0M
16105
Stacking Cable, 5.0M
SummitStack/UniStack Stacking Cable, 3.0M
3
SummitStack Stacking Cable, 5.0M
Not supported when using with Summit X650 and UniStack
Make Your Network Mobile
Corporate
and North America
Extreme Networks, Inc.
3585 Monroe Street
Santa Clara, CA 95051 USA
Phone +1 408 579 2800
Europe, Middle East, Africa
and South America
Phone +31 30 800 5100
Asia Pacific
Phone +65 6836 5437
Japan
Phone +81 3 5842 4011
extremenetworks.com
© 2012 Extreme Networks, Inc. All rights reserved. Extreme Networks, the Extreme Networks logo, Extreme Standby Router Protocol, ExtremeXOS, ExtremeXOS ScreenPlay,
Ridgeline, Summit, SummitStack and UniStack are either registered trademarks or trademarks of Extreme Networks, Inc. in the United States and/or other countries. sFlow is the
property of InMon Corporation. Specifications are subject to change without notice. 1242_23 04/2012
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising