ACTi | TCM-1111 | User`s manual | ACTi TCM-1111 User`s manual

ACTi TCM-1111 User`s manual
TCM-1111
H.264 Megapixel Outdoor IP IR D/N PoE
Bullet Camera
Hardware User’s Manual
Ver. 2011/11/30
TCM-1111 Hardware User’s Manual
Table of Contents
0.
Precautions
3
1.
Introduction
4
Package Contents ........................................................................... 4
Features and Benefits ..................................................................... 5
Safety Instructions .......................................................................... 6
Physical description ........................................................................ 8
Preparing for Installation ............................................................. 10
Remove the back cover by unscrewing the three attachments .... 10
Remove the sunshade by unscrewing the two screws ................. 10
How to Do the Waterproof Installation ....................................... 11
Basic Connections ......................................................................... 14
Product Specification .................................................................... 15
2.
Accessing Camera
16
If you have DHCP server / router in your network: ...................... 16
If you do NOT have DHCP server / router in your network: ......... 16
2
www.acti.com
TCM-1111 Hardware User’s Manual
0. Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to
follow the safety instruction given may directly endanger people, cause damage to the system
or to other equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your
local office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.
FCC/CE Regulation
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the users will be required to correct the
interference at their own expense.
3
www.acti.com
TCM-1111 Hardware User’s Manual
1. Introduction
Package Contents
TCM-1111
Product CD
(No Bracket Included)
Warranty Card
4
www.acti.com
TCM-1111 Hardware User’s Manual
Features and Benefits
This is a cutting-edge digital video surveillance camera. It can compress and transmit real time
images with outstanding image quality (18 FPS @ SXGA, 1280x1024) through a standard
TCP/IP network. This camera is your best choice to build an intelligent IP surveillance system.
H.264/MPEG-4/MJPEG Triple Codec Dual Streaming
This device supports 3 compression formats, H.264, MPEG-4 and MJPEG. It brings superior
image quality at 18 frames per second up to a resolution of SXGA (1280 x 1024) pixels, and
offers up to 26 frames per second in HD720 (1280x720). In D1 (720 x 480) / VGA (640 x 480) /
QVGA / QQVGA the device reaches 30 frames per second.
Built-in Hardware Motion Detection
No more external motion sensors are required. You may assign up to 3 video motion detection
areas. By tuning the object size and sensitivity, it will reliably detect objects passing though in
view. Hardware motion detection also offers better sensitivity and faster response time than
software motion detection.
Powerful Bundled Surveillance Software
To extend the capabilities of the camera, a powerful surveillance program is included in the
package for free. Users can easily use an existing PC as a digital video recorder. Scheduled
recording and manual recording keep every important video recorded in the local hard disk.
Reliable and accurate motion detection with instant warning enables immediate response in
every condition. Quick and simple search and playback function lets you easily find the images
and video you want.
Software Development Kit Support
This camera can be integrated or controlled by applications from third party software
developers. Software developers can save considerable efforts by using our Streaming Library
or ActiveX control. Please contact us for details on integration support.
5
www.acti.com
TCM-1111 Hardware User’s Manual
Safety Instructions
Don’t use the power supply with other voltages
This device is likely to be damaged or damage other equipments / personnel, if you use a
power supply with different voltage than the one included with this device. All warranty of this
product will be voided in the situations above.
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may
cause hazards.
Water and Moisture
Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool and the like.
Don’t use accessories not recommended by the manufacturer
Only install this device and the power supply in a dry place protected from weather
Servicing
Do not attempt to service this video product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to
qualified service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the video product has been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in
this manual. Adjust only those controls that are covered by the instruction manual, as an
improper adjustment of other controls may result in damage, and will often require
6
www.acti.com
TCM-1111 Hardware User’s Manual
extensive work by a qualified technician to restore the video product to its normal
operation.
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.
7
www.acti.com
TCM-1111 Hardware User’s Manual
Physical description
1) Ethernet Port
The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this
IP device can auto detect the speed of local network segment (10Base-T/100Base-TX
Ethernet).
2) Reset Button
Step 1: Switch off IP device by disconnecting the power cable
Step 2: Press and continue to hold the Reset Button (with a sharp tipped object, like a pen.)
Step 3: Reconnect the power cable while continuing to hold the reset button. The red
Power LED light will flash on for 3 second first, turn off for about 15 seconds, flash on for
another second and turn off again. By this time the reset to default operation is already
completed. This will take around 20 seconds from power up. You may then release the
reset button. This length of time fluctuates slightly with the environment. The Power LED light
will come back on and stay on after a few more seconds. The unit will start up with factory
default settings automatically.
Restore to Default
Complete
Power On
On (3s)
On
1s
Off (about 15s)
Off (10~15s)
Stay On
About 20 Seconds
8
www.acti.com
TCM-1111 Hardware User’s Manual
3) Power LED Indicator
The LED indicator lights up once the power is turned up. It will light up again when the device is
fully booted up.
9
www.acti.com
TCM-1111 Hardware User’s Manual
Preparing for Installation
Remove the back cover by unscrewing the three attachments
Remove the sunshade by unscrewing the two screws
10
www.acti.com
TCM-1111 Hardware User’s Manual
How to Do the Waterproof Installation
The following installation procedure makes the camera be water-resistant even for the
situations where the camera can easily be flooded by pouring rain.
The important part to focus on during the installation:
The protection of the cabling has to be done by a proper flex
conduit. The size of the flex conduit that matches with the
conduit gland is 1/2”. Please note that the conduit gland is
included to the package of the bullet camera.
The following images show the step-by-step procedure of
completing the water-proof installation.
1.
Disassemble the conduit gland as
shown on the photo.
2.
Pull the network cable through the flex
conduit. Please note that the size of the
conduit and the gland is big enough to let
the RJ-45 connector pass through all the
way.
3.
Two pieces from the conduit gland set
will be attached to flex conduit first.
11
www.acti.com
TCM-1111 Hardware User’s Manual
4.
The third piece goes through the back
side cover of the camera.
5.
The fourth piece (locking nut) is used
to lock the gland firmly from the inside of the
back side cover.
6.
Pull the network cable through the
back side cover of the camera.
7.
Connect the flex conduit to the back
side cover of the camera.
12
www.acti.com
TCM-1111 Hardware User’s Manual
8.
Tighten the domed sealing nut.
9.
Plug the network cable into the
camera’s RJ-45 connector before closing
the back side of the camera. If you are not
using PoE and need an additional power
cord then please connect it at this stage,
too.
10.
Tighten the screws of the back side of
the camera properly.
11.
Finally, the bullet camera with properly
mounted flex conduit as well as with proper
outdoor bracket would look like this. The
camera is now ready to withstand even the
most severe rain storms.
13
www.acti.com
TCM-1111 Hardware User’s Manual
Basic Connections
Follow the procedures below to connect the IP device to the respective apparatuses.
Please use a PoE (Power over Ethernet) supported switch or injector:
1) Connect your IP Camera to the Switch / Injector by CAT5 or CAT6 cables with RJ45
connector.
2) Connect your Switch / Injector to PC with another CAT5 / CAT6 network cable.
14
www.acti.com
TCM-1111 Hardware User’s Manual
Product Specification
TCM-1111
• Device
Device Type
Image Sensor
Sensor Size
Day / Night
Minimum Illumination
Color to B/W switch
Mechanical IR Cut Filter
IR Sensitivity Range
IR LED
Electronic Shutter
Bullet Camera
Progressive Scan CMOS
1/3” (4.8 x 3.6 mm)
Yes
Color: 0.5 lux at F1.0 (30 IRE, 2400°K); B/W: 0 lux (IR LED on)
CDS sensor based switch
Yes
700 - 1100 nm
IR LED x 20 (850 nm)
1/30 - 1/1,000 sec (60Hz); 1/25 - 1/1,000 sec (50Hz) (manual mode)
1/5 - 1/15,000 sec (auto mode)
• Lens
Focal Length
Iris
Focus
Horizontal Viewing Angle
• Video
Compression
Maximum Frame Rate
vs. Resolution
Multi-Streaming
Bit Rate
Bit Rate Mode
S/N Ratio
Image Enhancement
Privacy Mask
Text Overlay
Image Orientation
• Network
Protocol & Service
Ethernet Port
Security
• Alarm
Alarm Trigger
Alarm Response
• General
Power Source / Consumption
Weight
Dimensions (Φ x H)
Operating Temperature
Operating Humidity
Approvals
• Integration
Unified Solution
ISV Integration
Firmware Access Browser
Fixed focal, f4.2 mm / F1.8
Fixed iris
Fixed Focus
64.7°
H.264, MPEG-4 SP, MJPEG
18 fps at 1280 x 1024 (SXGA); 26 fps at 1280 x 720 (HD 720p); 30 fps at 640 x 480 (VGA);
30 fps at 320 x 240 (QVGA); 30 fps at 160 x 112 (QQVGA)
Simultaneous dual streams based on two configurations
28 Kbps - 6 Mbps (per stream)
Constant, Variable
More than 44 dB
White balance: automatic, hold, predefined and manual; Brightness; Saturation; Contrast; Sharpness;
Automatic gain control; Auto exposure: automatic, predefined and manual; Flickerless
4 configurable regions
User defined text on video
Image flip and mirror
TCP, UDP, HTTP, HTTPS, DHCP, PPPoE, RTP, RTSP, IPv6, DNS, DDNS, NTP, ICMP, ARP,IGMP,
SMTP, FTP, UPnP, SNMP, Bonjour
1, Ethernet (10/100 Base-T), RJ-45 connector
IP address filtering; HTTPS encryption; Password protected user levels; IEEE 802.1X network access
control
Video motion detection (3 regions)
Notify control center; Change camera settings; Command other devices; E-mail notification with snapshots;
Upload video, snapshot to FTP server
PoE Class 2 (IEEE802.3af) / 5.76 W (IR on)
610 g (1.35 lb)
77 mm x 193 mm (3.04”x7.60”)
-20 °C ~ 50 °c (-4 °F ~ 122 °F)
10% ~ 85% RH
CE, FCC, IP66
Fully compatible with ACTi software
Software Development Kit (SDK) available
Microsoft Internet Explorer 6.0 or newer
15
www.acti.com
TCM-1111 Hardware User’s Manual
2. Accessing Camera
If you have DHCP server / router in your network:
Many network server / routers are able to automatically provide IP addresses through DHCP. If
you are using such a network, just plug in your computer and IP Camera into the network and
your IP device will acquire network address by itself. Find and access the device with our IP
Utility program. You may download it at:
http://www.acti.com/product/detail/Software/ACTi_Utility_Suite
If you do NOT have DHCP server / router in your
network:
1. Configure your PC to use the same subnet by changing your PC’s IP address to the
subnet with prefix 192.168.0.XXX. The last number should be anything from 1 to 254
except 100 and other occupied IP addresses. Subnet mask should be 255.555.255.0.
2. The default IP used by this device is 192.168.0.100. Please make sure your PC is
NOT using this address and that no two equipments use the same IP address in
the network.
3. Change your IP address by going to Control Panel ->Manage Network Connections ->
Right click on the connection to change -> Option -> TCP/IP IPv4 Properties.
16
www.acti.com
TCM-1111 Hardware User’s Manual
Please set the settings as below.


IP address: 192.168. 0.xxx

Subnet mask: 255.255.255.
0
(NOTE: xxx should be a number
from 1 to 254 except 100, which is
used by the IP device. Please also
make sure that no two equipments
use the same IP address in the
same network..)
4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP:
192.168.0.100
5. When you see the login window, please input default user and password:
Default User: Admin
Password: 123456
6. After logging in, you will see the video from camera. To go to the main menu, click
the ”Setup” button on the top left.
17
www.acti.com
TCM-1111 Hardware User’s Manual
If you are using a single camera, this is enough to access the device.
If you are using multiple devices, you need to change the current device to another
unused IP address, so that when the next device is connected to the network, no two
devices use the same IP. Please perform the following steps.
7. Go to IP Settings -> Connection Type
8. Change the IP mode to Static.
9. Change the IP to 192.168.0.101 or any other unused IPs. Do NOT use the PC’s IP
address or 192.168.0.100.). If this is not the first device you add to the network, please
also avoid other devices’ IPs.
18
www.acti.com
TCM-1111 Hardware User’s Manual
10. Click “Apply”
11. Please go to System -> Save & Reboot, and click “Apply”. Internet Explorer will close
after a few seconds. This is normal.
12. Wait for 30 seconds, and open IE again to connect to the new IP. (In this example,
192.168.0.101). For the second device or more you add into the network, please type
the correct IP.
13. Adjust the default Video setting by going to Video -> Video
19
www.acti.com
TCM-1111 Hardware User’s Manual
20
www.acti.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising