Wayne Dalton 9700 Torsion Garage Door Installation Instructions And Owner’s Manual
Below you will find brief information for Garage Door 9700 Torsion. This manual provides guidance on installation, operation and maintenance of your new garage door. The document also contains important safety instructions and information about the parts supplied with the door. You will find information on how to install the door, how to properly attach the counterbalance cables and how to adjust the top fixture slide.
Advertisement
Advertisement
9700
T
o r s i o n
s
Tandard
l
ifT and
l
i g H T
c
o M M e r c i a l
, w
i n d l o a d
MH
i nsTallaTion
i nsTrucTions
a nd
o wner
’ s
M anual
T a b l e O f C o n t e n t s
Pre-Installation 2
Important Safety Instructions
Tools Required
Package Contents
Door Section Identification
Removing an Existing Door
Preparing the Opening
Parts Breakdown 5
Installation 6
3
3
Optional Installation 16
2
3
2
2
Door Arm Hookup
Inside Lock
16
16
Pull Down Rope 16
Maintenance 17
Cleaning Your Garage Door 17
Painting Your Garage Door
Maintaining The Finish On Your Garage Door
17
17
Operation And Maintenance 17
Warranty 18
PLEASE DO NOT RETURN THIS PRODUCT
TO THE STORE
Please Do Not Return This Product To The
Store. Please call 1-866-569-3799 (Press
Option 1) and follow the prompts to contact the appropriate customer service agent. They will be happy to handle any questions that you may have.
©Copyright 2015 Wayne Dalton, a Division Of Overhead Door Corporation
IMPORTANT NOTICES!
Wayne Dalton highly recommends that you read and fully understand the Installation Instructions and Owner’s Manual before you attempt this installation.
To avoid possible injury, read the enclosed instructions carefully before installing and operating the garage door. Pay close attention to all warnings and notes. After installation is complete, fasten this manual near garage door for easy reference.
DEFINITION OF DOOR HEIGHTS:
1. Door Heights less than or equal to 8’0” (< = 8’0”) are considered
Standard Lift Applications.
2. Door Heights greater than 8’0” (> 8’0”) are considered Light
Commercial Applications.
The complete Installation Instructions and Owner’s Manual are available at no charge from:
Wayne Dalton, a Division Of Overhead Door Corporation,
P.O. Box 67, Mt. Hope, OH., 44660, Or Online At
www.Wayne-Dalton.com.
Part Number 350276 REV1_04/30/2015
Pre-Installation
Important Safety Instructions
DEFINITION OF KEY WORDS USED IN THIS MANUAL:
INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH; IF NOT
AVOIDED, COULD RESULT IN SEVERE OR FATAL INJURY.
IMPORTANT: RIGHT AND LEFT HAND IS ALWAYS DETERMINED FROM INSIDE THE BUILDING
LOOKING OUT.
Tools Required
Power drill
Drill bits: 1/8”, 3/16”, 9/32”,
7/16”, 1/2”
Ratchet wrench
Socket driver: 7/16”
Sockets: 7/16”, 1/2”, 9/16”,
5/8”
Phillips head screwdriver
Locking Pliers
(2) Vice clamps
Wrenches: 3/8”, 7/16”, 1/2”,
9/16”, 5/8”
1/4” Torx bit
Approved winding rods
Hammer
Tape measure
Step Ladder
Level
Pencil
Saw Horses
Leather gloves
Safety glasses
CAUTION: PROPERTY DAMAGE OR INJURY CAN RESULT FROM FAILURE TO
FOLLOW INSTRUCTIONS.
IMPORTANT: REQUIRED STEP FOR SAFE AND PROPER DOOR OPERATION.
NOTE: Information assuring proper installation of the door.
READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING INSTALLATION. IF IN QUES-
TION ABOUT ANY OF THE PROCEDURES, DO NOT PERFORM THE WORK. INSTEAD, HAVE A
TRAINED DOOR SYSTEMS TECHNICIAN DO THE INSTALLATION OR REPAIRS.
1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.
2.
Wear protective gloves during installation to avoid possible cuts from sharp metal edges.
3.
It is always recommended to wear eye protection when using tools, otherwise eye injury could result.
4. Avoid installing your new door on windy days. Door could fall during the installation causing severe or fatal injury.
5. Doors 12’-0” wide and over should be installed by two persons, to avoid possible injury.
6. Operate door only when it is properly adjusted and free from obstructions.
7. If a door becomes hard to operate, inoperative or is damaged, immediately have necessary adjustments and/ or repairs made by a trained door system technician using proper tools and instructions.
8.
DO NOT stand or walk under a moving door, or permit anybody to stand or walk under an electrically operated door.
9.
DO NOT place fingers or hands into open section joints when closing a door. Use lift handles/ gripping points when operating door manually.
10. DO NOT permit children to operate garage door or door controls. Severe or fatal injury could result should the child become entrapped between the door and the floor.
11. Due to constant extreme spring tension, do not attempt any adjustment, repair or alteration to any part of the door, especially to springs, spring brackets, bottom corner brackets, fasteners, counterbalance lift cables or supports. To avoid possible severe or fatal injury, have any such work performed by a trained door systems technician using proper tools and instructions.
12. On electrically operated doors, pull down ropes must be removed and locks must be removed or made inoperative in the open (unlocked) position.
13. Top section of door may need to be reinforced when attaching an electric opener.
Check door and/ or opener manufacturer’s instructions.
14. Visually inspect door and hardware monthly for worn and or broken parts. Check to ensure door operates freely.
15. Test electric opener’s safety features monthly, following opener manufacturer’s instructions.
16. NEVER hang tools, bicycles, hoses, clothing or anything else from horizontal tracks.
Track systems are not intended or designed to support extra weight.
17. This door may not meet the building code wind load requirements in your area. For your safety, you will need to check with your local building official for wind load code requirements and building permit information.
After installation is complete, fasten this manual near the garage door.
IMPORTANT: STAINLESS STEEL OR PT2000 COATED LAG SCREWS MUST BE USED WHEN
INSTALLING CENTER BEARING BRACKETS, END BRACKETS, JAMB BRACKETS, DRAWBAR
OPERATOR MOUNTING/ SUPPORT BRACKETS AND DISCONNECT BRACKETS ON TREATED
LUMBER (PRESERVATIVE-TREATED). STAINLESS STEEL OR PT2000 LAG SCREWS ARE NOT
NECESSARY WHEN INSTALLING PRODUCTS ON UN-TREATED LUMBER.
NOTE: It is recommended that 5/16” lag screws are pilot drilled using a 3/16” drill bit, prior to fastening.
IMPORTANT: WHEN INSTALLING 5/16” LAG SCREWS USING AN ELECTRIC DRILL/ DRIVER,
THE DRILL/ DRIVERS CLUTCH MUST BE SET TO DELIVER NO MORE THAN 200 IN-LBS OF
TORQUE. FASTENER FAILURE COULD OCCUR AT HIGHER SETTINGS.
Package Contents
NOTE: Depending on the door model, some parts listed will not be supplied if not required.
Rear Back Hangs may not be included with your door.
Door sections (as required)
Torsion shaft or Torsion keyed shaft (as required)
Torsion keyed shafts (as required)
Quick Install flag angles RH/LH (as required) Fully Adjustable flag angles RH/LH (as required)
Riveted vertical track assemblies RH/LH (as required)
Vertical tracks RH/LH (as required)
Wall angle track assemblies RH/LH (as required)
Horizontal tracks RH/LH (as required)
(2) Horizontal angles (as required)
Q.I. Jamb brackets
(as required)
F.A. Jamb brackets
(as required)
Windload Jamb brackets (as required) Track rollers
Pull down rope
(if included)
Weather seals & nails (If included)
Door stop & nails
(If included)
Drawbar operator bracket (if included)
(2) Top fixture roller slides
(as required)
Strut (U-shaped)
(if included)
PRIOR TO WINDING OR MAKING ADJUSTMENTS TO THE SPRINGS, EN-
SURE YOU’RE WINDING IN THE PROPER DIRECTION AS STATED IN THE
INSTALLATION INSTRUCTIONS. OTHERWISE, THE SPRING FITTINGS MAY
RELEASE FROM SPRING IF NOT WOUND IN THE PROPER DIRECTION AND
COULD RESULT IN SEVERE OR FATAL INJURY.
2
(2) Top fixture assemblies (as required) Hinge bracket (as required)
Cable drums RH/LH
Center coupler assembly
(as required)
Counterbalance lift cables
Torsion springs RH/LH End bearing bracket RH/LH (as required)
Center bracket (as required)
Center bracket bushing
(as required)
Keys
(as required)
1/4”-20 x 9/16”
Track bolts (as required)
1/4”-20 x 11/16” Self drilling screws (as required)
1/4”-14 x 5/8” Self tapping screws (as required)
3/8”-16 x 3/4” Truss head bolts (as required)
5/16” x 1-1/4” Clevis pin Cotter pin
The INTERMEDIATE SECTION can be identified by #3 graduated end hinges (Only on a 4 section high door). The section will have a warning label attached to either the right or left hand end stile.
The TOP SECTION can be identified with no pre-installed graduated end or center hinges.
Warning label
Top section
#3
1-3/8”
#3 Graduated end hinge
Warning labels (Only on a 4 Section High Door)
Intermediate section
#2
#1
1-1/8”
#2 Graduated end hinge
Warning labels (Only on a 3 Section High Door)
Lock section
Bottom corner bracket warning labels
Bottom weather seal
Typical graduated end hinge stamping location
7/8”
#1 Graduated end hinge
Bottom corner bracket
Bottom weather seal
Section side view illustration
1/4”-20 x 7/8” Self drilling screws (as required)
3/8”- 16 Hex nuts
(as required)
5/16” x 1-5/8” Hex head lag screws
(as required)
1/4”- 20 Flanged hex nuts (as required)
5/16” x 1-5/8” Tamper-resistant hex head lag screws (as required)
3/8”-16 x 1-1/2” Hex bolts
5/16” x 2” Tamper-resistant hex head lag screw (as required)
Door Section Identification
Graduated end and center hinges are always pre-attached at the top of each section (except top section) and the graduated end hinges are stamped for identification, #1, #2, #3 and #4.
The stamp identifies the stacking sequence of the section. Depending on your door height, the sequence is always determined by #1 being the bottom section to #3 or #4 being the highest intermediate section. If the stamp on the graduated end hinge is illegible, refer to the section side view illustration. The section side view illustration shows the graduated end hinge profile of all sections, and can also be used to identify each section.
The BOTTOM SECTION can be identified by #1 graduated end hinges, the factory attached bottom astragal, the factory attached bottom corner brackets and by the bottom corner bracket warning labels on each end stile.
The LOCK SECTION can be identified by #2 graduated end hinges on a 4 section high door and by #3 graduated end hinges on a 3 section high door. Also, on a 3 section door, the lock section will come with a warning label attached to the right or left endstile.
3
Removing an Existing Door
IMPORTANT: COUNTERBALANCE SPRING TENSION MUST ALWAYS BE RELEASED BEFORE
ANY ATTEMPT IS MADE TO START REMOVING AN EXISTING DOOR.
WARNING
A POWERFUL SPRING RELEASING ITS ENERGY SUDDENLY CAN CAUSE
SEVERE OR FATAL INJURY. TO AVOID INJURY, HAVE A TRAINED DOOR
SYSTEMS TECHNICIAN, USING PROPER TOOLS AND INSTRUCTIONS,
RELEASE THE SPRING TENSION.
For detailed information see supplemental instructions “Removing an Existing Door/ Preparing the Opening”. These instructions are not supplied with the door, but are available at no charge from Wayne Dalton, A Division Of Overhead Door Corporation, P.O. Box 67, Mt. Hope,
OH., 44660, or at www.Wayne-Dalton.com.
Preparing the Opening
IMPORTANT: IF YOU JUST REMOVED YOUR EXISTING DOOR OR YOU ARE INSTALLING A
NEW DOOR, COMPLETE ALL STEPS IN PREPARING THE OPENING.
To ensure secure mounting of track brackets, side and center brackets, or steel angles to new or retro-fit construction, it is recommended to follow the procedures outlined in DASMA technical data sheets #156, #161 and #164 at
www.dasma.com.
The inside perimeter of your garage door opening should be framed with wood jamb and header material. The jambs and header must be securely fastened to sound framing members. It is recommended that 2” x 6” lumber be used. The jambs must be plumb and the header level. The jambs should extend a minimum of 12” (305 mm) above the top of the opening for Torsion counterbalance systems. For low headroom applications, the jambs should extend to the ceiling height. Minimum side clearance required, from the opening to the wall, is 3-1/2” (89 mm).
IMPORTANT: CLOSELY INSPECT JAMBS, HEADER AND MOUNTING SURFACE. ANY WOOD
FOUND NOT TO BE SOUND, MUST BE REPLACED.
For Torsion counterbalance systems, a suitable mounting surface (2” x 6”) must be firmly attached to the wall, above the header at the center of the opening.
NOTE: Drill a 3/16” pilot hole in the mounting surface to avoid splitting the lumber. Do not attach the mounting surface with nails.
WEATHERSTRIPS (MAY NOT BE INCLUDED):
Depending on the size of your door, you may have to cut or trim the weatherstrips (if neces-
sary) to properly fit into the header and jambs.
NOTE: If nailing product at 40°F or below, pre-drilling is required.
NOTE: Do not permanently attach weatherstrips to the header and jambs at this time.
For Quick Install track: For the header, align the weatherstrip with the inside edge of the header and temporarily secure it to the header with equally spaced nails. Starting at either side of the jamb, fit the weatherstrip up tight against the temporarily attached weatherstrip in the header and flush with the inside edge of the jamb. Temporarily secure the weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom section from falling out of the opening during installation. Equally space nails approximately 12” to 18” apart.
For Fully Adjustable track: For the header, align the weatherstrip 1/8” to 1/4” inside the header edge, and temporarily secure it to the header with equally spaced nails. Starting at either side of the jamb, fit the weatherstrip up tight against the temporarily attached weatherstrip in the header and 1/8” to 1/4” inside the jamb edge. Temporarily secure the weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom section from falling out of the opening during installation. Equally space nails approximately 12” to 18” apart.
Headroom requirement: Headroom is defined as the space needed above the top of the door for tracks, springs, etc. to allow the door to open properly. If the door is to be motor operated, 2-1/2” (64 mm) of additional headroom is required.
NOTE: 6” low headroom conversion kit is available for 12” radius only. Contact your local
Wayne Dalton dealer.
Backroom requirement: Backroom is defined as the distance needed from the opening back into the garage to allow the door to open fully.
BACKROOM REQUIREMENTS
Door Height
6’0” to 7’0”
Track
15” Radius
Manual Lift
102” (2591 mm)
Motor Operated
125” (3175 mm)
7’1” to 8’0” 15” Radius 114” (2896 mm) 137” (3480 mm)
HEADROOM REQUIREMENTS
Track Type
15” Radius
Space Needed
14-1/2” (368 mm)
Suitable mounting surface
2”x 6” lumber minimum
Header board 2”x 6” lumber preferred
Headroom
Min. Side room
Clearance is 3 1/2”
Backroom
Nail
Min. Side room
Clearance is 3 1/2”
Level header
Weatherstrips
Finished
Door
Height
Plumb jambs
Finished
Door width
Jambs
Weatherstrips
Jamb
Quick Install track
Jamb
Other track systems
1/8” to 1/4”
Weatherstrips
4
PARTS BREAKDOWN
NOTE: The illustrations shown on this page are general representations of the door parts. Each specific door models may have unique variations.
J11.
J10.
J11.
J6.
J12.
J1.
J11.
J3.
J3.
J5a.
J7.
J10.
J1.
J6.
J8.
J9.
E1.
A2.
F2.
A1.
F2.
F1.
E2.
C1.
J11.
J2.
J5b.
F1.
J4.
C1.
J4.
A1.
B1.
B2.
A2.
G1.
H1.
Top of vertical track
3rd hole set
E3.
B3
J2.
I3.
E4.
I7.
2nd hole set
I5.
D2.
B2.
I1.
K1.
B1.
D1.
C2.
C1.
1st hole set
B3.
I4.
I6.
I3.
A. FLAG ANGLES (AS REQUIRED):
A1. Quick Install (Q.I.) Flag Angles
A2. Fully Adjustable (F.A.) Flag Angles
B. JAMB BRACKETS (AS REQUIRED):
B1. Quick Install (Q.I.) Jamb Brackets
B2. Fully Adjustable (F.A.) Jamb Brackets
B3. Windload Jamb Brackets
C. TRACK ROLLERS:
C1. Short Stem Track Rollers
C2. Long Stem Track Rollers
D. GRADUATED END HINGES:
D1. Single Graduated End Hinges (S.E.H.), Anti-Pinch
D2. Double Graduated End Hinges (D.E.H.), Anti-Pinch
E. STACKED SECTIONS:
E1. Top Section
E2. Intermediate(s) Section
E3. Lock Section
E4. Bottom Section
F. TOP FIXTURE (AS REQUIRED):
F1. Top Fixture Assemblies
F2. Top Fixture Roller Slides
G. STRUT(S) (AS REQUIRED):
G1. Strut (U-shaped)
H. DRAWBAR OPERATOR BRACKET (FOR TROLLEY OPERATED DOORS):
I2.
B1. (Quick
Install
Feature)
Top hole
Middle hole
Bottom hole
Top of vertical track
3rd hole set
2nd hole set
1st hole set
K1.
H1. Drawbar Operator Bracket
I. TRACKS (AS REQUIRED):
I1. Left Hand Horizontal Track Assembly
I2. Right Hand Horizontal Track Assembly
I3. Left Hand and Right Hand Vertical Tracks
I4. Left Hand Riveted Vertical Track Assembly
I5. Right Hand Riveted Vertical Track Assembly
I6. Left Hand Angle Mount Vertical Track Assembly
I7. Right Hand Angle Mount Vertical Track Assembly
J. TORSION SPRING ASSEMBLY (AS REQUIRED):
J1. Left Hand and Right Hand Torsion Springs (As Required)
J2. Counterbalance Lift Cables
J3. Left Hand End Bearing Bracket (As Required)
J4. Right Hand End Bearing Bracket (As Required)
J5a. Left Hand Cable Drum and J5b. Right Hand Cable Drum
J6. Center Bracket (As Required)
J7. Center Bracket Bushing (As Required)
J8. Center Bearing Bracket (As Required)
J9. Torsion Shaft / Torsion Keyed Shaft (As Required)
J10. Torsion Keyed Shafts (As Required)
J11. Keys (As Required)
J12. Center Coupler Assembly (As Required)
K. REAR BACK HANGS:
K1. Left Hand and Right Hand Rear Back Hang Assemblies
5
B2. (Fully
Adjustable
Feature)
B3.
(Windload
Jamb
Bracket)
Lower hole of hole/ slot pattern
Horizontal track angle
INSTALLATION
Quick
Install tabs
Before installing your door, be certain that you have read and followed all of the instructions covered in the pre-installation section of this manual. Failure to do so may result in an improperly installed door.
NOTE: Reference TDS 160 for general garage door terminology at www.dasma.com.
Quick Install Flag Angles
Tools Required: Safety glasses, Leather gloves
1
NOTE: If you have Fully Adjustable Flag Angles, Riveted Track or Angle Mount Track, skip this step.
NOTE: Flag angles are right and left handed.
Place the lower Quick Install tab of the left hand flag angle in the Quick Install feature of the left hand vertical track. Give the flag angle 1/4 turn to lock in place. Repeat for other side.
Flag angle
Vertical track
Lower Quick
Install tab
Quick Install feature
Fully Adjustable Flag Angles
Tools Required: Safety glasses, Leather gloves
2
NOTE: If you have Quick Install flag angles, Riveted Track or Angle Mount Track, skip this step.
NOTE: Flag angles are right and left handed.
If you have Quick Install vertical tracks, hand tighten the left hand flag angle to the left hand vertical track using (1) stud plate and (2) 1/4” - 20 flange hex nuts. Repeat for the other side.
If you have Fully Adjustable vertical tracks, hand tighten the left hand flag angle to the left hand vertical track using (2) 1/4” - 20 x 9/16” track bolts and (2) 1/4” - 20 flange hex nuts.
Repeat for other side. Flange nuts will be secured after flag angle spacing is completed in step, Top Section.
Flag angle
1/4”-20
Flange hex nuts
Flag angle
1/4”-20
Flange hex nuts
Stud plate
1/4 Turn
Alignment hole
Key slots
Horizontal track
Quick Install tabs in place
Horizontal track angle
Horizontal track angle
4
Quick
Install tabs
Quick
Install tabs
Key slots
Quick Install tabs in place
Horizontal track
Horizontal track
Quick Install Jamb Brackets
Tools Required: Tape measure, Safety glasses, Leather gloves
6’0”
6’6”
6’8”
6’10”
7’0”
7’3”
7’6”
7’9”
8’0” (4
Sec)
NOTE: If you have Fully Adjustable jamb brackets, Riveted Track or Angle Mount Track, skip this step.
Measure the length of the vertical tracks. Using the jamb bracket schedule, determine the placement of the jamb brackets for your door height and track length. To install the jamb brackets, align the Quick Install tab on the Quick Install jamb bracket with the Quick Install feature in the vertical track and turn the bracket perpendicular to the track so the mounting flange is toward the back (flat) leg of the track. Repeat for other side.
Jamb Bracket Schedule
DOOR
HEIGHT
TRACK
LENGTH
JAMB
BKT
3RD SET
POSITION
64.00”
70.00”
72.00”
74.00”
76.00”
79.00”
82.00”
85.00”
88.00”
3
3
3
3
3
3
3
JAMB
BKT
1ST SET
POSITION
5
3
M
M
B
B
M
B
B
B
M
5
5
6
5
5
5
5
JAMB
BKT
2ND SET
POSITION
6
5
B
B
B
B
B
B
B
B
T
6
6
-
6
7
-
-
-
B
B
-
B
M
-
-
-
B= BOTTOM HOLE, M= MIDDLE HOLE, T= TOP HOLE
1st hole set 2nd hole set
Vertical track Top of track
3rd hole set
Quick Install vertical track
3
Fully Adjustable vertical track
Horizontal Track Angles
Tools Required: Hammer, Safety glasses, Leather gloves
1/4”- 20 x 9/16”
Track bolts
NOTE: For larger doors, a full length horizontal track angle may not already be spot welded to the horizontal track. If the horizontal track angle is not welded, the horizontal track angle will be installed, as shown.
Position the left hand horizontal track angle, as shown. Place the Quick Install tabs of the horizontal track angle in the key slot of the left hand horizontal track. Using a hammer, tap the horizontal track angle towards the curved end of the track until the alignment hole in the track and angle are aligned. Repeat for other side. Set tracks aside.
Bottom hole
Middle hole
Top hole
Q.I. tab
Q.I. jamb bracket
Jamb bracket in place
Mounting flange
6
5
Fully Adjustable Jamb Brackets
Tools Required: Tape measure, Safety glasses, Leather gloves
NOTE: If you have Quick Install jamb brackets, Riveted Track or Angle Mount Track, skip this step.
NOTE: The bottom jamb bracket is always the shortest bracket, while the center jamb bracket is the next tallest. If three jamb brackets per side are included with your door, you will have received a top jamb bracket, which is the tallest.
To attach the bottom jamb bracket, locate lower hole of the hole/ slot pattern of the 1st hole set on the vertical track. Align the slot in the jamb bracket with the lower hole of the hole/ slot pattern. Secure jamb bracket using (1) 1/4” - 20 x 9/16” track bolt and (1) 1/4” - 20 flange hex nut. Repeat for other side.
Place the center jamb bracket over the lower hole of the hole/ slot pattern that is centered between the bottom jamb bracket and flag angle of the 2nd hole set. Secure jamb bracket using (1) 1/4” - 20 x 9/16” track bolt and (1) 1/4” - 20 flange hex nut. Repeat for other side.
If a top jamb bracket was included, secure it to vertical track using the lower hole of the hole/ slot pattern in the 3rd hole set and (1) 1/4” - 20 x 9/16” track bolt and (1) 1/4” - 20 flange hex nut. Repeat for other side.
Vertical track Top of track
1st hole set 2nd hole set 3rd hole set
Lower hole of hole/ slot pattern
1/4”- 20
Flange hex nut
1/4”- 20 x 9/16”
Track bolt
Jamb bracket in place
F.A. jamb bracket
6
Windload Jamb Brackets
Tools Required: Tape measure, Safety glasses, Leather gloves
NOTE: The following (JB-1’s) denotes a slotted windload jamb bracket.
Measure the length of the vertical tracks. Using the Jamb Bracket Schedule (shown on the
Windload Specification Sheet), determine the placement of the windload jamb brackets for your door height. Loosely fasten the windload jamb bracket to the vertical track with (1) 1/4”
- 20 x 9/16” track bolt and (1) 1/4” - 20 flange hex nut. Repeat for other side.
Vertical track
(1) 1/4”- 20 X 9/16”
Track bolt
Windload jamb bracket
(1) 1/4”- 20
Flange hex nut
Counterbalance Cables and Track Rollers
Tools Required: Tape measure, Safety glasses, Leather gloves
7
NOTE: Refer to door section identification, located in the pre-installation section of this manual or refer to Parts Breakdown.
Cable loop
Bottom corner bracket warning label
8
#1 Single graduated end hinge
(Hinge tube)
Short stem track roller
Counterbalance lift cable
Bottom section
Counterbalance lift cable
Double graduated end hinge
(Hinge tube)
Long stem track roller
Bottom corner bracket warning label
Milford pin
Bottom section
Cable loop
Bottom corner bracket
Short stem track roller
Milford pin
Bottom weather seal
Short stem track roller
Bottom corner bracket
Struts
Tools Required: Power drill, 7/16” Socket driver, Level, Step ladder, Tape measure, Safety glasses, Leather gloves
NOTE: Refer to Door Section Identification, located in the pre-installation section of this manual.
NOTE: Refer to Package Contents / Parts Breakdown, to determine if strut(s) and or hinge bracket(s) are required to be installed.
NOTE: Some struts may be factory installed.
Depending on the size of your door, one or more sections may require a strut(s) and hinge bracket(s). Using sawhorses, lay sections together on a flat smooth surface. Ensure the graduated end hinges and center hinges are on top of their corresponding sections. Refer to the Windload Specification Sheet for the strutting schedule and the illustrations.
9
Bottom Section
Tools Required: Tape measure, Level, Wooden shims (if necessary), Safety glasses, Leather gloves
Center the bottom section in the door opening. Level the section using wooden shims (if necessary) under the bottom section. When the bottom section is leveled, temporarily hold it in place by driving a nail into the jamb and bending it over the edge of the bottom section on both sides.
FAILURE TO ENSURE TIGHT FIT OF CABLE LOOP OVER MILFORD PIN
COULD RESULT IN COUNTERBALANCE LIFT CABLE COMING OFF THE PIN,
ALLOWING THE DOOR TO FALL, POSSIBLY RESULTING IN SEVERE OR
FATAL INJURY.
Uncoil the counterbalance lift cables. Starting on the left hand side, place the cable loop on the milford pin of the bottom corner bracket. Insert a short stem track roller into the factory attached bottom corner bracket and another into the #1 graduated end hinge at the top of the bottom section. Repeat for other side.
NOTE: Check to ensure cable loops fits tightly over the milford pins.
NOTE: Larger doors will use long stem track rollers with double graduated end hinges. They will also use short stem track rollers for the factory attached bottom corner brackets.
NOTE: Verify bottom weather seal is aligned with bottom section. If there is more than 1/2” excess weather seal on either side, trim weather seal even with bottom section.
Weather seal (If applicable)
Level
Bottom section
7
10
Wooden shims (If necessary)
Vertical Tracks
Tools Required: Power Drill, 3/16” Drill bit, 7/16” Socket driver, Tape measure,
Level, Step ladder, Safety glasses, Leather gloves
NOTE: Depending on your door, you may have Quick Install Flag Angles, Fully Adjustable
Flag Angles, Riveted Vertical Track Assemblies or you may have Angle Mount Vertical Track
Assemblies. Refer to Package Contents / Parts Breakdown, to determine which Flag Angles /
Vertical Track Assemblies you have.
IMPORTANT: IF YOUR DOOR IS TO BE INSTALLED PRIOR TO A FINISHING CONSTRUCTION
OF THE BUILDING’S FLOOR, THE VERTICAL TRACKS AND THE DOOR BOTTOM SECTION
ASSEMBLY SHOULD BE INSTALLED SUCH THAT WHEN THE FLOOR IS CONSTRUCTED, NO
DOOR OR TRACK PARTS ARE TRAPPED IN THE FLOOR CONSTRUCTION.
IMPORTANT: THE TOPS OF THE VERTICAL TRACK ASSEMBLIES MUST BE LEVEL FROM SIDE
TO SIDE. IF THE BOTTOM SECTION WAS SHIMMED TO LEVEL IT, THE VERTICAL TRACK AS-
SEMBLY ON THE SHIMMED SIDE MUST BE RAISED THE HEIGHT OF THE SHIM.
Position the left hand vertical track assembly over the track rollers of the bottom section.
Make sure the counterbalance lift cable is located between the track rollers and the door jamb. Drill 3/16” pilot holes into the door jamb for the lag screws.
FOR QUICK INSTALL FLAG ANGLES OR FULLY ADJUSTABLE FLAG ANGLES: Loosely fasten jamb brackets and flag angle to the jamb using 5/16” x 1-5/8” lag screws. Tighten lag screws, securing the bottom jamb bracket to jamb, maintain 3/8” to 5/8” spacing, between the bottom section and vertical track. Hang counterbalance lift cable over flag angle. Repeat same process for other side.
Identification on page 3.
NOTE: Make sure graduated end and center hinges are flipped down, when stacking another section on top.
NOTE: Larger doors will use long stem track rollers with double graduated end hinges.
Place track rollers into graduated end hinges of remaining sections.
With assistance, lift second section and guide the track rollers into the vertical tracks. Lower section until it is seated against bottom section. Align vertical marks in the upper alignment sticker, with the lower alignment sticker on right hand side, on the back of door. Keep sections aligned and fasten center hinge(s) first; then end hinges last using 1/4” - 14 x 5/8” self tapping screws.
NOTE: To prevent center hinge leaf(s) from rotating, first secure the top middle hole of the center hinge leaf with one 1/4” - 14 x 5/8” self-tapping screw then secure the other two holes.
NOTE: Larger doors with double graduated end hinges, fasten both hinges to connect the sections using 1/4” - 14 x 5/8” self-tapping screws.
Repeat same process for other sections, except top section.
IMPORTANT: PUSH & HOLD THE HINGE LEAFS SECURELY AGAINST THE SECTIONS WHILE
SECURING WITH 1/4” - 14 X 5/8” SELF TAPPING SCREWS. THERE SHOULD BE NO GAP
BETWEEN THE HINGE LEAFS AND THE SECTIONS.
Flag angle
Vertical track assembly
Jamb bracket
5/16” x 1-5/8”
Lag screws
Bottom section
Track rollers
Floor
12R FA 15R FA 12R QI 15R QI
Flag angle lag screw locations
3/8” to 5/8”
Spacing
Bottom section
Vertical track
Track roller
FOR RIVETED VERTICAL TRACK ASSEMBLY: Loosely fasten jamb brackets and flag angle to the jamb using 5/16” x 1-5/8” lag screws. Tighten lag screws, securing the bottom jamb bracket to jamb, maintain 3/8” to 5/8” spacing as shown between the bottom section and vertical track. Hang counterbalance lift cable over flag angle. Repeat same process for other side.
FOR ANGLE MOUNT VERTICAL TRACK ASSEMBLY: Loosely fasten the slots in the wall angle to the jamb using 5/16” x 1-5/8” lag screws. Tighten lag screws, securing the bottom slot in the wall angle, maintain 3/8” to 5/8” spacing as shown between the bottom section and vertical track. Hang counterbalance lift cable over angle mount. Repeat same process for other side.
Angle mount vertical track assembly
Riveted vertical track assembly
Wall angle
Slot
11
5/16” x 1-5/8”
Lag screws
Vertical track
Flag angle
5/16” x 1-5/8”
Lag screws
Vertical track
Jamb bracket
Bottom section
3/8” to 5/8”
Spacing
Flag angle lag screw locations
Bottom section
Bottom section
Vertical track
Floor
Stacking Sections
Tools Required: Power drill, 7/16” Socket driver, Tape measure, Level, Step ladder, Safety glasses, Leather gloves
NOTE: The sections can be identified by the graduation of the factory installed end hinges.
The smallest graduated end hinge on section should be stacked on top of the bottom section, with each graduated end hinge increasing as the sections are stacked, see Door Section
8
Left double graduated end hinge with long stem track roller
Vertical tracks
Lock section
Alignment sticker
Alignment sticker
Right double graduated end hinge with long stem track roller
12
1/4”-14 x 5/8” Self tapping screw locations
Secure top middle hole first
Left graduated end hinge with short stem track roller
Center hinge(s)
Right graduated end hinge with short stem track roller
Top Fixtures
Tools Required: Power drill, 7/16” Socket driver, Step ladder, Safety glasses,
Leather gloves
NOTE: Depending on your door, you may have Top Fixture Roller Slides or you may have
Top Fixture Assemblies. Refer to the Windload Specification Sheet, Package Contents, Parts
Breakdown, to determine which Top Fixtures you have.
IF YOU HAVE TOP FIXTURE ASSEMBLIES: Referring to the Windload Specification Sheet and using the illustrations below, determine if your top fixtures are supposed to be installed next to the strut or installed below the strut. Starting on the left hand side of the top section, place the top of the top fixture base onto the top section, as shown. Next, secure the top fixture to the top section using (4) 1/4” - 20 x 7/8” self drilling screws. Loosen the 5/16” - 18 hex nut on the top fixture slide. The top fixture slide will be tightened and adjusted later, in step, Adjusting Top Fixture. Insert a short stem track roller into top fixture slide. Repeat same process for other side.
Top fixture assembly
Strut
(2) 1/4”-20 x 7/8”
Self-drilling screws
Top section
Top fixture slide
5/16” - 18 Hex nut and
5/16” - 18 x 5/8” Carriage bolt
Short stem track roller
Top fixture base Endcap
(2) 1/4”-20 x 7/8”
Self-drilling screws
Top section
(2) 1/4”-20 x 7/8”
Self-drilling screws
Top fixture slide
Short stem track roller
Strut
5/16” - 18 Hex nut and
5/16” - 18 x 5/8” Carriage bolt
(1)Top fixture assembly
Top fixture base
Endcap
(2) 1/4”-20 x 7/8” Self-drilling screws
IF YOU HAVE TOP FIXTURE ROLLER SLIDES: Starting on the left hand side of the top section and using the top fixture template (shown on the Windload Specification Sheet), determine the placement for the top fixture roller slide on the bottom portion of the strut. Mark and pre-drill the strut, as shown on the template. Fasten the top fixture roller slide to the strut using (2) 1/4” - 14 x 5/8” self tapping screws. Repeat same process for other side.
Bottom of strut
Top section
Top fixture roller slide
Top fixture roller slide installed
Strut
Top section
(2) 1/4”-14 x 5/8”
Self tapping screws
Short stem track roller
Drawbar Operator Bracket
Tools Required: Power drill, 7/16” Socket driver, Phillips head screwdriver, Step ladder, Tape measure, Safety glasses, Leather gloves
13
NOTE: If you’re installing a drawbar operator, the drawbar operator bracket must be mounted and secured prior to installing top section.
IMPORTANT: WHEN CONNECTING A DRAWBAR OPERATOR TYPE GARAGE DOOR OPENER
TO THIS DOOR, A WAYNE DALTON OPERATOR/ DRAWBAR OPERATOR BRACKET MUST
BE SECURELY ATTACHED TO THE TOP SECTION OF THE DOOR, ALONG WITH ANY STRUT
PROVIDED WITH THE DOOR. THE INSTALLATION OF THE DRAWBAR OPERATOR MUST BE AC-
CORDING TO MANUFACTURER’S INSTRUCTIONS AND FORCE SETTINGS MUST BE ADJUSTED
PROPERLY.
Remove, but retain (4-6) 1/4” - 20 x 7/8” self drilling screws from the center of the strut, allowing the drawbar operator bracket to slide between the section and the strut.
NOTE: For retro fit applications, the drawbar operator bracket must be aligned with an existing drawbar operator.
Locate the center of the top section and slide drawbar operator bracket under strut until the drawbar operator bracket is seated against the strut flange.
NOTE: Prior to fastening drawbar operator bracket to top section, ensure the top edge of drawbar operator bracket is aligned with the top edge of the section, as shown.
Attach the drawbar operator bracket using (6) 1/4” - 20 x 5/8” self drilling screws (as shown). Finish re-attaching the strut using the self tapping screws removed previously.
14
Strut
Top section
1/4” - 20 x 7/8”
Self-drilling screws
Strut
Top section
Drawbar operator bracket
Drawbar operator bracket in place under strut
(8) 1/4” - 20 x 11/16”
Self-drilling screws
Top Section
Tools Required: Power drill, 7/16” Socket driver, 7/16” Wrench, Step ladder,
Tape measure, Safety glasses, Leather gloves
Place the top section in the opening. Temporarily secure the top section by driving a nail in the header near the center of the door and bending it over the top section. Now, flip up the hinge leaves, hold tight against section, and fasten center hinges first and end hinges last
(refer to step, Stacking Sections). Vertical track alignment is critical. Position flag angle or wall angle between 1-11/16” (43 mm) to 1-3/4” (44 mm) from the edge of the door; tighten the bottom lag screw. Flag angles or wall angles must be parallel to the door sections. Repeat for other side.
IMPORTANT: THE DIMENSION BETWEEN THE FLAG ANGLES OR WALL ANGLES MUST BE
DOOR WIDTH PLUS 3-3/8” (86MM) TO 3-1/2” (89 MM) FOR SMOOTH, SAFE DOOR OPERA-
TION.
FOR QUICK INSTALL TRACK: Complete the vertical track installation by securing the jamb bracket(s) and tightening the other lag screws. Repeat for other side.
FOR FULLY ADJUSTABLE TRACK OR RIVETED TRACK: Complete the vertical track installation by securing the jamb bracket(s) and tightening the other lag screws. Push the vertical track against the track rollers so that the track rollers are touching the deepest part of the curved side of the track; tighten all the track bolts and nuts. Repeat for other side.
FOR ANGLE MOUNT TRACK: Complete the vertical track installation by securing the jamb bracket(s) and or tightening the other lag screws. Push the vertical track against the track rollers so that the track rollers are touching the deepest part of the curved side of the vertical track, as shown. Repeat for other side.
Door width
+ 3-3/8” to 3-1/2”
Top of flag angle or
Top of wallangle assembly
Nail
Top section
1-11/16” to 1-3/4”
Flag angle
Flag angle or wallangle assembly
Top section
Vertical track against track rollers
Horizontal Tracks
Tools Required: Ratchet wrench, 9/16” 7/16” Socket, 9/16” 7/16” Wrench, Step ladder, Tape measure, Safety glasses, Leather gloves
15
NOTE: Depending on your door, you may have Quick Install Flag Angles, Fully Adjustable
Flag Angles, Riveted Vertical Track Assemblies or you may have Angle Mount Vertical Track
Assemblies. Refer to Package Contents / Parts Breakdown, to determine which Flag Angles /
Vertical Track Assemblies you have.
DO NOT RAISE DOOR UNTIL HORIZONTAL TRACKS ARE SECURED AT
REAR, AS OUTLINED IN STEP, REAR BACK HANGS, OR DOOR COULD FALL
FROM OVERHEAD POSITION CAUSING SEVERE OR FATAL INJURY.
IF YOU HAVE QUICK INSTALL FLAG ANGLES: To install horizontal track, place the curved end over the top track roller of the top section. Align key slot of the horizontal track with the
Quick Install tab of the flag angle. Push curved portion of horizontal track down to lock in place.
Flag angle
Flag angle
Horizontal track
Quick
Install tab
Quick
Install tab in place
Tracks flush
3/8”-16
Hex nut
Horizontal track angle
Key slot
3/8”-16 x 3/4”
Truss head bolt
IF YOU HAVE FULLY ADJUSTABLE FLAG ANGLES: To install horizontal track, place the curved end over the top track roller of the top section. Align the bottom of the horizontal track with the top of the vertical track. If you have Quick Install horizontal track, tighten the horizontal track to the flag angle with a stud plate and (2) 1/4” - 20 flange hex nuts. If you have Universal horizontal track, tighten the horizontal track to the flag angle with (2) 1/4” - 20 x 9/16” track bolts and (2) 1/4” - 20 flange hex nuts.
9
Quick Install horizontal track
1/4”-20
Flange hex nuts
Fully Adjustable horizontal track
1/4”-20
Flange hex nuts
Horizontal track angle
3/8”-16
Hex nut
Flag angle upper slot
Flag angle upper slot
Stud plate
1/4”-20 x 9/16”
Track bolts
3/8”-16 x 3/4”
Truss head bolt
IF YOU HAVE RIVETED TRACK ASSEMBLIES OR ANGLE MOUNT VERTICAL TRACK
ASSEMBLIES: To install horizontal track, place the curved end over the top roller of the top section. Align the bottom of the horizontal track with the top of the vertical track. Tighten the horizontal track to the Flag Angle / Angle Mount with (2) 1/4” - 20 x 9/16” track bolts and (2)
1/4” - 20 flange hex nuts.
Horizontal track
Rivited flag angle
3/8”-16 x 3/4”
Truss head bolt
1/4”-20
Flange hex nuts
3/8”-16
Hex nut
Horizontal track angle
NOTE: End bearing brackets are right and left hand.
Attach the left hand end bearing bracket through either the end bearing bracket’s upper or lower slots to the left hand horizontal track angle using (2) 3/8” - 16 x 3/4” truss head bolts and (2) 3/8” - 16 nuts.
IMPORTANT: THE END BEARING BRACKET’S LOWER SLOTS ARE USED ON DOORS WITH
12” RADIUS TRACK; THE UPPER SLOTS ARE USED ON DOORS WITH 15” RADIUS TRACK.
Secure the top of the end bearing bracket to the jamb using 5/16” x 1-5/8” lag screw(s).
Repeat the same process for right hand side.
Left end bracket
(2) 3/8”-16
Hex nuts
(2) 3/8”-16 x 3/4”
Truss head bolts
(1) 5/16” x 1-5/8”
Lag screw
Upper slots
Lower slots
Horizontal track angle
Rivited flag angle upper slot
Horizontal track
1/4”-20 x 9/16”
Track bolts
Horizontal track
Angle mount
3/8”-16
Hex nut
Angle mount
1/4”-20
Flange hex nuts
Horizontal track angle
1/4”-20
Flange hex nuts
Flag angle
1/4”-20 x 9/16”
Track bolts
1/4”-20 x 9/16”
Track bolts
Horizontal track
3/8”-16 x 3/4”
Truss head bolt
Next level the horizontal track assembly and bolt the horizontal track angle to the first encountered slot in the flag angle / angle mount using (1) 3/8” - 16 x 3/4” truss head bolt and (1) 3/8” - 16 hex nut. Repeat for other side. Next remove the nail that was temporarily holding the top section in place, installed in step, Top Section.
IMPORTANT: FAILURE TO REMOVE NAIL BEFORE ATTEMPTING TO RAISE DOOR COULD
CAUSE PERMANENT DAMAGE TO TOP SECTION.
Adjusting Top Fixtures
Tools Required: 7/16” Wrench, Step ladder, Safety glasses, Leather gloves
16
(2) 3/8”-16
Hex nuts
18
Bend back and fourth to seperate the (2) end bearing brackets
Left end bracket
(2) 3/8”-16 x 3/4”
Truss head bolts
Upper slot
Lower slots
(3) 5/16” x 1-5/8”
Lag screws
Horizontal track angle
Center Bracket
Tools Required: Step ladder, Power drill, 7/16” Socket driver, 3/16” Drill bit, 1/4”
Torx bit, Level, Tape measure, Pencil, Safety glasses, Leather gloves
With horizontal tracks installed, you can now adjust the top fixtures. Vertically align the top section of the door with the lower sections. Once aligned, position the top fixture slide, out against the horizontal track. Maintaining the top fixture slide position, tighten the (1) 5/16”
- 18 nut to secure the slide to the top fixture. Repeat for other side. Next, lock each of the top fixture slides into place using (1) 1/4” - 20 x 9/16” track bolt and (1) 1/4” - 20 hex nut through any two aligning holes.
Short stem track roller
5/16”-18
Hex nut
Horizontal track
Top section
Top section
Strut
Top section
(1)1/4”-20
Track bolt and
(1) 1/4”-20 flange hex nut
Top fixture slide
Int. section
Correct
Int. section
Incorrect
17
End Bearing Brackets
Tools Required: Step ladder, Power drill, 3/16” Drill bit, Ratchet wrench, 7/16”
Socket driver, 9/16” Socket, 9/16” Wrench, Tape measure, Safety glasses,
Leather gloves
NOTE: Refer to Package Contents / Parts Breakdown, to determine which End Bearing
Brackets you have.
NOTE: Prior to fastening end bearing brackets into the door jamb, pilot drill using a 3/16” drill bit.
IMPORTANT: RIGHT AND LEFT HAND IS ALWAYS DETERMINED FROM INSIDE THE BUILDING
LOOKING OUT.
NOTE: Depending on your door’s configuration you may have to break the end bearing brackets apart.
10
NOTE: Refer to Package Contents / Parts Breakdown, to determine which Center Bracket(s) came with your door.
NOTE: Prior to fastening center bracket(s) into the door jamb, pilot drill using a 3/16” drill bit.
NOTE: Refer to Package Contents / Parts Breakdown, to determine if your door came with a coupler assembly. If your door came with a coupler assembly, the mounting surface needs to be a minimum of 17” wide. The two center bearing brackets will need to be spaced 12” to
14” apart at the center of the door, as shown.
NOTE: If your door came with (4) springs, each of the outer springs mounting surface will need to be a minimum of 3” wide.
NOTE: If needed, measure the diameter of your springs. If you have a one piece shaft with
3-3/4” diameter springs, they do not share center brackets and do not have a coupler assembly.
First, locate the center of the door. Mark a vertical pencil line on the mounting surface above the door, at the center. Measure from the center of the bearing, in one of the end bearing brackets, downwards, to the top the door. Using that measurement, measure that distance upwards from the top of the door to the mounting surface and mark a horizontal pencil line which intersects the vertical pencil line.
Mounting surface
Vertical line
Typicall center of end bearing bracket
Horizontal line
Typicall center bracket
IMPORTANT: RIGHT AND LEFT HAND IS ALWAYS DETERMINED FROM INSIDE THE BUILDING
LOOKING OUT.
IMPORTANT: IDENTIFY THE TORSION SPRINGS PROVIDED AS EITHER RIGHT HAND WOUND
(RED WINDING CONE), WHICH GOES ON THE LEFT HAND SIDE OR LEFT HAND WOUND
(BLACK WINDING CONE), WHICH GOES ON THE RIGHT HAND SIDE.
IMPORTANT: ON SINGLE SPRING APPLICATIONS, ONLY A LEFT HAND WOUND (BLACK
WINDING CONE), WHICH GOES ON THE RIGHT HAND SIDE IS REQUIRED.
NOTE: The set screws used on all torsion winding cones and cable drums are now colored red. DO NOT identify right and left hand by the set screw color.
IF YOU DON’T HAVE A COUPLER ASSEMBLY:
Facing the inside of the door, lay the torsion shaft / torsion keyed shaft on the floor. Lay the torsion spring with the black winding cone and the black cable drum at the right end of the torsion shaft / torsion keyed shaft. Lay the torsion spring with the red winding cone and the red cable drum at the left end of the torsion shaft / torsion keyed shaft.
Slide the center bracket bearing / center bracket bushing onto the torsion shaft / torsion keyed shaft followed by the torsion springs and cable drums.
IMPORTANT: THE CENTER BRACKET BEARING / CENTER BRACKET BUSHING, TORSION
SPRINGS, AND CABLE DRUMS MUST BE POSITIONED, AS SHOWN.
Equal distance (top of door section to horizontal line)
IF YOUR DOOR DID NOT COME WITH A CENTER COUPLER ASSEMBLY OR TORSION
SPRINGS LESS THAN 3-3/4” ID: Mark a vertical pencil line on the mounting surface above the door, at the center. Align the edge of the center bracket with the vertical pencil line and the center of the center bracket with the horizontal pencil line; this is to ensure the torsion shaft is level between the center and end bearing brackets.
NOTE: On some single spring doors, the single spring can be longer than half the opening width. If your spring is longer, then the center bracket must be mounted off center for the spring to fit properly. Measure spring length to determine appropriate center bracket location.
Mounting surface
(3” Minimum)
Center bracket bushing assembly
(2) 5/16” x 1-5/8”
Lag screws
Vertical line
Mounting surface
(3” Minimum)
Vertical line
(2) 5/16” x 1-5/8”
Lag screws
Horizontal line
Horizontal line
(1) 5/16” X 2” or (1) 5/16” x 1-5/8” Tamper-resistant lag screw
Center bearing bracket assembly
If your door did come with a center coupler assembly or 3-3/4” ID Torsion Springs: Mark a vertical pencil line on the mounting surface above the door, at the center. Split the difference up and position the (2) center bearing brackets apart from each other. Mark two vertical pencil lines, one for each center bearing bracket onto the mounting surface above the door.
NOTE: If your door came with a center coupler assembly or if it utilizes 3-3/4” springs, the springs will not share a center bracket.
NOTE: If your door has (4) springs, split the distance between the center of the door and the end bracket on each side to locate the intermediate center brackets.
Attach each of the center bracket(s) to the mounting surface, using (2) 5/16” x 1-5/8” lag screws and (1) 5/16” x 2” tamper-resistant lag screw.
IMPORTANT: USE A 5/16” X 1-5/8” TAMPER-RESISTANT LAG SCREW INSTEAD OF THE
5/16” X 2” TAMPER-RESISTANT LAG SCREW IF MOUNTING SURFACE IS MOUNTED OVER
MASONRY. TAMPER-RESISTANT LAG SCREW MUST BE ATTACHED THROUGH THE BOTTOM
HOLE OF THE CENTER BRACKET(S).
Mounting surface
(17” Minimum)
Center of door
Vertical line
Vertical line
†12”
(2) 5/16” x 1-5/8”
Lag screws
(2) 5/16” x 1-5/8”
Lag screws
19
Horizontal line
(1) 5/16” X 2” or (1) 5/16” x 1-5/8” Tamper-resistant lag screw
† (2) Center bearing brackets spaced 6” to 7” apart from the center of the door.
Torsion Spring Assembly
Tools Required: 3/8” Wrench, 9/16” Wrench, Step ladder, Tape measure, Safety glasses, Leather gloves
NOTE: Refer to the Package Contents and or Parts Breakdown to determine if your door came with a coupler assembly.
11
Left hand cable drum, red
Right hand cable drum, black
Torsion shaft
Center bearing
Left wound, black winding cone
(right hand side)
Right wound, red winding cone (left hand side)
SPRING APPLICATIONS,
ONLY A LEFT WOUND
(BLACK WINDING CONE),
WHICH GOES ON THE RIGHT
HAND SIDE IS REQUIRED.
With assistance, pick up the torsion spring assembly and slide one end of the torsion shaft
/ torsion keyed shaft through one end bearing bracket. Lay the middle of the torsion shaft / torsion keyed shaft into the center bracket. Slide the other end of the torsion shaft / torsion keyed shaft into the other end bearing bracket. Position the torsion shaft / torsion keyed shaft so that equal amounts of the shaft extend from each end bearing bracket.
Left hand end bearing bracket
Equal spacing
Center bracket bushing
Right hand end bearing bracket
Torsion shaft
Center bracket
IF YOU HAVE A COUPLER ASSEMBLY:
Disassemble the coupler assembly by removing the (3) 3/8” - 16 x 1-3/4” hex head screws and the (3) 3/8” - 16 nylon hex lock nuts from the coupler halves. Loosen the set screws.
Set the components aside. Facing the inside of the door, lay the (2) torsion keyed shafts on the floor. One torsion keyed shaft on the left hand side and the other torsion keyed shaft on the right hand side. Starting on the left hand side, lay one of the coupler halves, the center bearing, torsion spring with the red winding cone and the red cable drum at the left end of the torsion keyed shaft. Next on the right hand side, lay the other coupler half, center bearing, the torsion spring with the black winding cone, and the black cable drum at the right end of the torsion keyed shaft.
Slide the coupler halves, center bearings onto the torsion keyed shafts followed by the torsion springs and the cable drums, as shown.
IMPORTANT: THE COUPLER HALVES, CENTER BEARINGS, TORSION SPRINGS, CABLE
DRUMS MUST BE POSITIONED, AS SHOWN.
Slide the flat edge of the couple half flush with the side edge of the torsion keyed shaft. Insert
(1) key into the slot of both the coupler half and the slot in the torsion keyed shaft. Tighten the (2) set screws and the locking nut to secure the coupler half to the torsion keyed shaft, as shown.
NOTE: Tighten the set screws to 14-15 ft. lbs. of torque (once set screws contact the shaft, tighten set screws one full turn). Repeat the same process for the other coupler half.
Set screws and Lock nut
Coupler halves
Black cable drum
(right hand side)
Center coupler assembly
(3) 3/8” - 16 x 1-3/4” Hex head screws and (3) 3/8” - 16 Nylon hex lock nut
Torsion keyed shaft
Coupler halves
Center bearing
Left wound, black winding cone
(right hand side)
Key Red cable drum
(left hand side)
Center bearing
Right wound, red winding cone
(left hand side)
Torsion keyed shaft
Set screws and Lock nut
Key
Set screws and Lock nut
Coupler halves
Black cable drum
(right hand side)
Torsion keyed shaft
Coupler halves assembled
Center coupler assembly
Center bearing
(3) 3/8” - 16 x 1-3/4” Hex head screws and (3) 3/8” - 16 Nylon hex lock nut
Coupler halves
Left wound, black winding cone
(right hand side)
Key Red cable drum
(left hand side)
Center bearing
Center bearing
Right wound, red winding cone
(left hand side)
Torsion keyed shaft
Set screws and Lock nut
Key
Coupler halves assembled
With assistance and starting on the left hand side of door, pick up the left hand torsion spring assembly and slide one end of the torsion keyed shaft through the end bearing bracket. Lay the other side of the torsion keyed shaft into the center bracket. Repeat the same process for the right hand torsion spring assembly. Position both torsion keyed shafts so that equal amounts of the shafts extend from each end bearing brackets.
Equal spacing
Center bearing brackets
Torsion keyed shaft
Right hand end bearing bracket
Center bearing
Torsion keyed shaft
Coupler half
Equal spacing
Right wound, red winding cone (left hand side)
Left hand end bearing bracket
Left hand end bearing bracket
Equal spacing
Center bracket bushing
Right hand end bearing bracket coupler assembly.
IMPORTANT: THE SPRING WARNING TAG(S) SUPPLIED MUST BE SECURELY ATTACHED
TO THE STATIONARY SPRING CONE(S) IN PLAIN VIEW. SHOULD A REPLACEMENT SPRING
WARNING TAG BE REQUIRED, CONTACT WAYNE DALTON FOR FREE REPLACEMENTS.
NOTE: Measure the diameter of your springs. If your spring diameter is 3-3/4”, the springs do not share center brackets. If your spring diameter is either 2” or 2-5/8”, then two springs will share the same center bracket, unless a coupler assembly is provided.
IF YOU DON’T HAVE A COUPLER ASSEMBLY:
Slide center bracket bushing into the spring. Align the stationary spring cone(s) with the holes in the center bracket bushing assembly. Secure the torsion spring(s) to the center bracket bushing assembly with (2) 3/8” - 16 x 1-1/2” hex head bolts and (2) 3/8” - 16 nuts.
IF YOU HAVE A COUPLER ASSEMBLY:
Slide center bracket bushing into the spring. Align the stationary spring cone with the holes in the center bracket. Secure the torsion spring to the center bracket with (2) 3/8”-16 x 1-1/2” hex head bolts and (2) 3/8” - 16 nuts. Repeat the same process for the other center bearing bracket.
At the middle of the two center bearing brackets, re-assemble the coupler assembly by loosely fastening the coupler halves together using the (3) 3/8” - 16 x 1-3/4” hex head screws and the (3) 3/8” - 16 nylon hex lock nuts, as shown.
NOTE: Ensure both torsion keyed shafts have equal amounts of the shafts extending from each end bearing bracket.
Stationary spring cone
Typical center bracket
Torsion spring
Stationary spring cone
Torsion spring
Torsion spring
(2) 3/8”-16 Nuts
Stationary spring cone
Typical center bracket bushing
Spring warning tags
Typical center bracket assembly
(2) 3/8”-16 x 1-1/2”
Hex head bolts
Torsion spring
(3) 3/8” - 16 x 1-3/4” hex head screws and
(3) 3/8” - 16 Hex nuts
Torsion spring
Stationary spring cone
Center bracket
Torsion spring
21
Center bracket
Coupler assembly
Coupler halves
(2) 3/8”-16 x 1-1/2”
Hex head bolts and (2)
3/8”-16 Hex nuts
Counterbalance Lift Cables
Tools Required: Step ladder, Locking pliers, 3/8” Wrench, Tape measure, Safety glasses, Leather gloves
20
Torsion keyed shafts Center bracket
Torsion Spring Attachment
Tools Required: Step ladder, Ratchet Wrench, 9/16” Socket, 9/16” Wrench, Tape measure, Safety glasses, Leather gloves
NOTE: Refer to Package Contents / Parts Breakdown, to determine which Center Bracket(s) came with your door.
NOTE: Refer to Package Contents / Parts Breakdown, to determine if your door came with a
12
Starting on the left hand side, thread the counterbalance lift cable up and around the front side of the left hand cable drum.
IMPORTANT: VERIFY THAT THERE ARE NO COUNTERBALANCE LIFT CABLE OBSTRUCTIONS.
NOTE: Always assemble the left hand cable and cable drum first to help maintain equal cable tension on both sides of the door.
Hook the counterbalance lift cable into the left hand cable drum. Slide the left hand cable drum up against the left hand end bearing bracket. Counterbalance lift cable should terminate at the 3 o’clock position. Tighten the (2) set screws in the drum to 14-15 ft. lbs. of torque (once set screws contact the shaft, tighten screws one full turn).
NOTE: If you have torsion keyed shaft(s), insert (1) key into the slot of both the cable drum and the slot in the torsion keyed shaft, as shown.
Rotate the left hand drum and torsion shaft until counterbalance lift cable is taut. Now attach locking pliers to the torsion shaft and brace locking pliers up against jamb to keep counterbalance lift cable taut. Repeat for right hand side.
IMPORTANT: INSPECT EACH COUNTERBALANCE LIFT CABLE MAKING SURE THEY ARE
SEATED PROPERLY ONTO THE CABLE DRUMS AND THAT BOTH COUNTERBALANCE LIFT
CABLES HAVE EQUAL TENSION.
Once the counterbalance cables are set and if applicable tighten the coupler assembly together by tightening the (3) 3/8” - 16 nylon hex lock nuts to secure the coupler halves together.
Typicall left hand end bearing bracket
Typicall left hand cable drum
Torsion shaft /
Torsion keyed shaft c. Counterbalance lift cables are correctly installed and wound onto cable lift drums.
d. Counterbalance lift cables are taut and have equal tension on both sides.
e. Cable lift drums are against end bearing brackets and set screws are tight.
f. Torsion spring or springs are installed correctly.
g. Review the label attached to the spring warning tag, to determine number of spring turns required.
NOTE: Door MUST be closed and locked when winding or making any adjustments to the torsion spring(s).
WARNING
FAILURE TO ENSURE DOOR IS IN A CLOSED POSITION AND TO PLACE
VICE CLAMP ONTO VERTICAL TRACK CAN ALLOW DOOR TO RAISE AND
CAUSE SEVERE OR FATAL INJURY.
Winding Bars
(Steel Rods)
Size Of Winding Bar
(Inches)
1/2” dia. x 18”
5/8” dia. x 24”
Spring Diameter
Used On
2” and 2-5/8”
3-3/4”
C-Clamps
Counterbalance lift cable
Counterbalance lift cable hooked in cable drum
Typical sections
Vice clamps above third track roller on both sides of door
Jamb
Locking pliers
Typicall left hand end bearing bracket
Key
24
Vice clamps / C-Clamps attached to inner and outer rail of vertical track
Bottom section
Winding Spring(s)
Tools Required: Step ladder, Approved winding bars, 3/8” Wrench, Tape measure, Safety glasses, Leather gloves
Counterbalance lift cable
Typicall left hand cable drum
Set screws
WINDING TORSION SPRING(S) IS AN EXTREMELY DANGEROUS PROCE-
DURE AND SHOULD BE PERFORMED ONLY BY A TRAINED DOOR SYSTEM
TECHNICIAN USING PROPER TOOLS AND INSTRUCTIONS.
Torsion shaft /
Torsion keyed shaft(s)
Chalking Torsion Spring(s)
Tools Required: Step ladder, Chalk, Safety glasses, Leather gloves
22
Draw a chalk line horizontally along the center of the torsion spring coil(s). As the torsion spring is wound, the chalk line will create a spiral. This spiral can be used to count and determine the number of turns that are applied on the torsion spring.
Original horizontal chalk line, prior to winding
Torsion shaft
Center bracket
Torsion spring coils
Winding cone
23
Spirals created after winding
Securing Door for Spring Winding
Tools Required: Vice clamps, Safety glasses, Leather gloves
With the door in the fully closed position, place vice clamps / c-clamps onto both vertical tracks just above the third track roller. This is to prevent the garage door from rising while winding springs.
NOTE: Check the following before attempting to wind torsion spring(s): a. Counterbalance lift cables are secured at bottom corner brackets.
b. Counterbalance lift cables are routed unobstructed to cable drums.
13
USE ONLY SPECIFIED WINDING BARS, AS STATED IN STEP SECURING
DOOR FOR SPRING WINDING. DO NOT SUBSTITUTE WITH SCREWDRIV-
ERS, PIPE, ETC. OTHER TOOLS MAY FAIL OR RELEASE FROM THE SPRING
CONE AND CAUSE SERIOUS PERSONAL INJURY.
PRIOR TO WINDING OR MAKING ADJUSTMENTS TO THE SPRINGS, EN-
SURE YOU’RE WINDING IN THE PROPER DIRECTION AS STATED IN THE
INSTALLATION INSTRUCTIONS. OTHERWISE THE SPRING FITTINGS MAY
RELEASE FROM SPRING IF NOT WOUND IN THE PROPER DIRECTION AND
COULD RESULT IN SEVERE OR FATAL INJURY.
Position a ladder slightly to the side of the spring so that the winding cone is easily accessible, and so your body is not directly in line with the winding bars.
Check the label attached to the spring warning tag for the required number of complete turns to balance your door.
Door Height Approximate Spring Turns
6’0”
6’3”
6’6”
6’8”
6’9”
7’0”
6-7/8
7-1/8
7-1/4
7-3/8
7-1/2
7-5/8
7’3”
7’6”
7’9”
8’0”
7-7/8
8
8-1/4
8-3/4
Alternately inserting the winding rods into the holes of the spring winding cone, rotate the winding cone upward toward the ceiling, 1/4 turn at a time, until the required number of complete turns for your door height is achieved. As the last 1/8 to 1/4 turn is achieved, securely hold the winding rod and carefully stretch the torsion spring 1/8” - 1/4”. Next while still securely holding the winding rod, tighten both set screws in the winding cone to 14-15 ft. lbs. of torque (once set screws contact the torsion shaft, tighten screws one full turn).
Carefully remove winding rod from winding cone. Repeat for the opposite spring. While holding the door down to prevent it from raising unexpectedly in the event the spring(s) were over-wound, carefully remove the locking pliers from the torsion shaft and vertical tracks.
Adjustments to the number of turns stated may be necessary. If door rises off floor under spring tension alone, reduce spring tension until door rests on the floor. If the door is hard to rise or drifts down on its own, add spring tension.
Torsion spring(s) should be wound in the direction the end coil points.
Perforated Angle Gauge Weight Limitations:
1-1/4” x 1-1/4” x 15 Gauge Door Weight Less Than 220 lbs.
1-1/4” x 1-1/4” x 16 Gauge Door Weight Less Than 175 lbs.
NOTE: If an opener is installed, position horizontal tracks one hole above level when securing it to the rear back hangs.
KEEP HORIZONTAL TRACKS PARALLEL AND WITHIN 3/4” TO 7/8” MAXI-
MUM OF DOOR EDGE, OTHERWISE DOOR COULD FALL, RESULTING IN
SEVERE OR FATAL INJURY.
IMPORTANT: DO NOT SUPPORT THE WEIGHT OF THE DOOR ON ANY PART OF THE REAR
BACK HANGS THAT CANTILEVERS 4” OR MORE BEYOND A SOUND FRAMING MEMBER.
NOTE: If rear back hangs are to be installed over drywall, use (2) 5/16” x 2” hex head lag screws and make sure lag screws engage into solid structural lumber.
NOTE: 26” angle must be attached to sound framing members and nails should not be used.
Now, permanently attach the weatherstrips on both door jambs and header. The weatherstrips were temporarily attached in Preparing the Opening, in the pre-installation section of this manual.
NOTE: When permanently attaching the weatherstrips to the jambs, avoid pushing the weatherstrips too tightly against the face of door.
Torsion spring(s)
Spring coils
Approved winding rod
Winding cone
HIGH SPRING TENSION CAN CAUSE
SERIOUS INJURY OR DEATH.
HIGH SPRING TENSION CAN CAUSE
SERIOUS INJURY OR DEATH.
which springs are connected, such as steel brackets, cables, wood blocks, fasteners or other parts of the counterbalance system.
Adjustments or repairs must ONLY be made by a
DO NOT remove, cover or paint over this tag. Product user should inspect this tag periodically for legibility and should order a replacement tag from
©Copyright 2010 Overhead Door Corporation 102081 REV2 06/24/2010 which springs are connected, such as steel brackets, cables, wood blocks, fasteners or other parts of the counterbalance system.
Adjustments or repairs must ONLY be made by a
DO NOT remove, cover or paint over this tag. Product user should inspect this tag periodically for legibility and should order a replacement tag from
©Copyright 2010 Overhead Door Corporation 102081 REV2 06/24/2010
Warning tag(s)
25
Set screws
TAG(S) ATTACHED TO THE SPRING(S)
FOR THE REQUIRED NUMBER OF
COMPLETE TURNS, TO BALANCE
YOUR DOOR.
Torsion shaft
Approved winding rod
Rear Back Hangs
Tools Required: Ratchet wrench, Socket: 1/2” 5/8”, Wrench: 1/2” 5/8”, (2) Vice clamps, Tape measure, Level, Step ladder, Safety glasses, Leather gloves
IMPORTANT: HOLD THE DOOR DOWN TO PREVENT IT FROM RISING UNEXPECTEDLY IN THE
EVENT THE SPRING(S) WAS OVER-WOUND AND CAUTIOUSLY REMOVE VICE CLAMPS FROM
VERTICAL TRACKS.
Raise the door until the top section and half of the next section are in the horizontal track radius. Do not raise door any further since rear of horizontal tracks are not yet supported.
RAISING DOOR FURTHER CAN RESULT IN DOOR FALLING AND CAUSE
SEVERE OR FATAL INJURY.
Clamp a pair of vice clamps onto the vertical tracks just above the second track roller on one side, and just below the second track roller on the other side. This will prevent the door from raising or lowering while installing the rear back hangs.
Using the chart (Perforated Angle Gauge Weight Limitations) below, use the appropriate perforated angle (may not be supplied), (2) 5/16” x 1-5/8” hex head lag screws and (3) 5/16” bolts with nuts (may not be supplied), fabricate rear back hangs for the horizontal tracks.
Attach the horizontal tracks to the rear back hangs with 5/16” - 18 x 1” hex bolts and nuts
(may not be supplied). Horizontal tracks must be level and parallel with door within 3/4” to
7/8” maximum of door edge.
PRIOR TO WINDING OR MAKING ADJUSTMENTS TO THE SPRINGS, EN-
SURE YOU’RE WINDING IN THE PROPER DIRECTION AS STATED IN THE
INSTALLATION INSTRUCTIONS. OTHERWISE THE SPRING FITTINGS MAY
RELEASE FROM SPRING IF NOT WOUND IN THE PROPER DIRECTION AND
COULD RESULT IN SEVERE OR FATAL INJURY.
Now, lift door and check its balance. Adjustments to the required number of spring turns stated may be necessary. If door rises off floor under spring tension alone, reduce spring tension until door rests on the floor. If the door is hard to rise or drifts down on its own, add spring tension. A poorly balanced door can cause garage door operator operation problems.
To adjust spring tension, fully close door. Apply vice grips to track above third track roller.
Insert a winding rod into the winding cone. On single spring doors, counterbalance lift cable tension must be maintained by placing vice grips on torsion shaft before loosening set screws in the winding cone. Push upward on the winding rod while carefully loosening the set screws in the winding cone. BE PREPARED TO SUPPORT THE FULL FORCE OF THE
TORSION SPRING ONCE THE SET SCREWS ARE LOOSE. Carefully adjust spring tension 1/4 turn. Retighten both set screws in the winding cone and repeat for the other side. Recheck door balance. DO NOT ADJUST MORE THAN 1/2 TURN FROM THE RECOMMENDED NUMBER
OF TURNS.
If the door still does not operate easily, lower the door into the closed position, UNWIND THE
SPRING(S) FULLY (Reference the insert “Removing The Old Door / Preparing The Opening” section on torsion spring removal) and recheck the following the items:
1.) Check the door for level.
2.) Check the torsion shaft for level.
3.) Check the track spacing.
4.) Check the counterbalance cables for equal tension and proper wrap onto the cable drums.
5.) Check the track for potential obstruction of the track rollers.
6.) Clamp locking pliers onto track and rewind springs.
IMPORTANT: IF DOOR STILL DOES NOT OPERATE PROPERLY, THEN CONTACT A TRAINED
DOOR SYSTEM TECHNICIAN.
EXCEEDING THE RECOMMENDED LISTED DOOR WEIGHT LIMITATIONS OF
SPECIFIC GAUGE PERFORATED ANGLES MAY RESULT IN DOOR FALLING
WHEN RAISED, CAUSING SEVERE OR FATAL INJURY.
VERIFY PERFORATED BACK HANG ANGLE LOAD RATINGS WITH BACK
HANG ANGLE SUPPLIER.
Perforated Angle Gauge Weight Limitations:
Perforated Angle Gauge Door Weight
2” x 2” x 12 Gauge
1-1/4” x 1-1/4” x 13 Gauge
Door Weight Less Than 800 lbs.
Door Weight Less Than 305 lbs.
14
Vice clamp
Horizontal tracks
2nd Track roller
Vice clamp
3/4” To 7/8”
Door edges
Horizontal tracks
3/4” To 7/8”
Sound framing members
Horizontal track
5/16”-18 x 1-1/4”
Hex bolt must extend into the track to serve as a roller stop
Perforated angle bolted using (2) 5/16” x 1-5/8” hex head lag screws to ceiling member and parallel to door
(3) 5/16” Bolts and nuts
Perforated angle
Sound framing members
(3) 5/16”
Bolts and nuts
Horizontal track
Perforated angle
5/16”-18 x 1-1/4”
Hex bolt must extend into the track to serve as a roller stop
Perforated angle bolted using (2) 5/16” x 1-5/8” hex head lag screws to ceiling member and parallel to door
15
Optional Installation
Door Arm Hookup
Align hole in the door arm with holes in drawbar operator bracket tabs, as shown. Insert
5/16” x 1-1/4” clevis pin, making sure hole in clevis pin is outside of second tab of drawbar operator bracket. Insert hairpin cotter into clevis pin hole and spread hairpin cotter to secure assembly, as shown.
Drawbar operator bracket tabs
Cotter pin
Door arm
Clevis pin
5/16”x 1-1/4”
Clevis pin
Inside Lock
Drawbar operator bracket
Spread cotter pin
Install the inside lock on the second section of the door. Secure the lock to the section with
(4) 1/4” - 20 x 11/16” self drilling screws. Square the lock assembly with the door section, and align with the square hole in the vertical track. The inside lock should be spaced approximately 1/8” away from the section edge.
IMPORTANT: INSIDE LOCK(S) MUST BE REMOVED OR MADE INOPERATIVE IN THE UN-
LOCKED POSITION IF AN OPERATOR IS INSTALLED ON THIS DOOR.
Second section 1/8”
Square hole in vertical track
Inside lock
(4) 1/4”-20 x 11/16”
Self drilling screws
End cap
Pull Down Rope
WARNING
DO NOT INSTALL PULL DOWN ROPE ON DOORS WITH OPERATORS.
CHILDREN MAY BECOME ENTANGLED IN THE ROPE CAUSING SEVERE OR
FATAL INJURY.
Measure and mark the jamb approximately 48” to 50” (1220 to 1270 mm) from floor on the right or left side of jamb. Drill 1/8” pilot hole for no. 6 screw eye. Tie the pull down rope to the no. 6 screw eye and to the bottom corner bracket, as shown.
No. 6 Screw eye
Pull down rope
48” to 50”
From floor
Pull down rope
Bottom corner bracket
16
Maintenance
Cleaning Your Garage Door
IMPORTANT: DO NOT USE A PRESSURE WASHER ON YOUR GARAGE DOOR!
While factory-applied finishes on garage doors are durable, it is desirable to clean them on a routine basis. Some discoloration of the finish may occur when a door has been exposed to dirt-laden atmosphere for a period of time. Slight chalking may also occur as a result of direct exposure to sunlight.
Cleaning the door will generally restore the appearance of the finish. To maintain an aesthetically pleasing finish of the garage door, a periodic washing of the garage door is recommended.
THE FOLLOWING CLEANING SOLUTION IS RECOMMENDED:
A mild detergent solution consisting of one cup detergent (with less than 0.5% phosphate) dissolved into five gallons of warm water will aid in the removal of most dirt.
NOTE: The use of detergents containing greater than 0.5% phosphate is not recommended for use in general cleaning of garage doors.
NOTE: Be sure to clean behind weatherstrips on both sides and top of door.
or drawbar operator bracket supplied with the door. To avoid possible damage to your door,
Wayne Dalton recommends reinforcing the top section on models 8000, 8100, 8200 and
9100 doors with a strut (may or may not be supplied). The installation of the drawbar operator must be according to manufacturer’s instructions and force settings must be adjusted properly. Refer to the owner’s manual supplied with your drawbar operator for complete details on installation, operation, maintenance and testing of the operator.
MAINTAINING YOUR GARAGE DOOR:
Before you begin, read all warning labels affixed to the door and the installation instructions and owner’s manual. Perform routine maintenance steps once a month, and have the door professionally inspected once a year. Review your Installation Instructions and Owner’s
Manual for the garage door. These instructions are available at no charge from Wayne Dalton,
A Division Of Overhead Door Corporation, P.O. Box 67, Mt. Hope, OH., 44660, or at
www.
Wayne-Dalton.com. For additional information on garage door/operator maintenance go to
www.dasma.com and reference TDS 151, 167 and 179.
Monthly Inspections:
1. Visual Inspection: Closely inspect jambs, header and mounting surface. Any wood found not to be structurally sound must be replaced. Inspect the springs, counterbalance lift cables, track rollers, pulleys, rear back hangs and other door hardware for signs of worn or broken parts. Tighten any loose screws and/or bolts. Check exterior surface of the door sections for any minor cracks. Verify door has not shifted right or left in the opening. If you suspect problems, have a trained door system technician make the repairs.
CAUTION: NEVER MIX CLEANSERS OR DETERGENTS WITH BLEACH.
GLASS CLEANING INSTRUCTIONS
Clean with a mild detergent solution (same as above) and a soft cloth. After cleaning, rinse thoroughly.
ACRYLIC CLEANING INSTRUCTIONS
Clean acrylic glazing with nonabrasive soap or detergent and plenty of water. Use your bare hands to feel and dislodge any caked on particles. A soft, grit-free cloth, sponge or chamois may be used to wipe the surface. Do not use hard or rough cloths that will scratch the acrylic glazing. Dry glazing with a clean damp chamois.
NOTE: Do not use any window cleaning fluids, scouring compounds, gritty cloths or solventbased cleaners of any kind.
Painting Your Garage Door
Refer to Instruction Insert “
Field Painting and Finishing Fiberglass or Steel Door Sec-
tions”.
Maintaining The Finish
On Your Garage Door
If the factory finish is beginning to fade, the door may require a field applied top clear coat.
Depending on environment and usage, this may be necessary after 1 to 3 years of use. Refer to Instruction Insert “ Field Painting and Finishing Fiberglass Or Steel Door Sections”.
Operation And Maintenance
GARAGE DOOR SPRINGS, COUNTERBALANCE LIFT CABLES, BRACK-
ETS, AND OTHER HARDWARE ATTACHED TO THE SPRINGS ARE UNDER
EXTREME TENSION, AND IF HANDLED IMPROPERLY, CAN CAUSE SEVERE
OR FATAL INJURY. ONLY A TRAINED DOOR SYSTEMS TECHNICIAN
SHOULD ADJUST THEM, BY CAREFULLY FOLLOWING THE MANUFAC-
TURER’S INSTRUCTIONS.
OPERATING YOUR GARAGE DOOR:
Before you begin, read all warning labels affixed to the door and the installation instructions and owner’s manual. When correctly installed, your Wayne Dalton door will operate smoothly.
Always operate your door with controlled movements. Do not slam your door or throw your door into the open position, this may cause damage to the door or its components. If your door has an electric opener, refer to the owner’s manual to disconnect the opener before performing manual door operation below.
Manual door operation:
For additional information on manual garage door operations go to
www.dasma.com and reference TDS 165.
IMPORTANT: DO NOT PLACE FINGERS OR HANDS INTO SECTION JOINTS WHEN OPENING
AND/OR CLOSING A DOOR. ALWAYS USE LIFT HANDLES / SUITABLE GRIPPING POINTS
WHEN OPERATING THE DOOR MANUALLY.
Opening a Door: Make sure the lock(s) are in the unlocked position. Lift the door by using the lift handles / suitable gripping points only. Door should open with little resistance.
Closing a Door: From inside the garage, pull door downward using lift handles / gripping point only or a high friction area only. If you are unable to reach the lift handles/ suitable gripping points only, use pull down rope affixed to the side of door. Door should close completely with little resistance.
Using an electric operator:
IMPORTANT: PULL DOWN ROPES MUST BE REMOVED AND LOCKS MUST BE REMOVED OR
MADE INOPERATIVE IN THE UNLOCKED POSITION.
When connecting a drawbar (trolley type) garage door operator to this door, an drawbar operator and or drawbar operator bracket must be securely attached to the top section of the door, along with any struts provided with the door. Always use the drawbar operator and
17
NEVER REMOVE, ADJUST, OR LOOSEN THE BOLTS, SCREWS AND/OR
LAG SCREWS ON THE COUNTERBALANCE (END OR CENTER BEARING
BRACKETS) SYSTEM OR BOTTOM CORNER BRACKETS OF THE DOOR.
THESE BRACKETS ARE CONNECTED TO THE SPRING(S) AND ARE UNDER
EXTREME TENSION. TO AVOID POSSIBLE SEVERE OR FATAL INJURY,
HAVE ANY SUCH WORK PERFORMED BY A TRAINED DOOR SYSTEMS
TECHNICIAN USING PROPER TOOLS AND INSTRUCTIONS.
TorqueMaster
®
Plus Springs: Pawl knob(s) (located on the TorqueMaster
®
end brackets above the door) should be engaged to prevent the door from rapidly descending in case of spring failure or forceful manual operation.
Torsion Springs: The torsion springs (located above the door) should only be adjusted by a trained door systems technician. DO NOT attempt to repair or adjust torsion springs yourself.
Extension Springs: A restraining cable or other device should be installed on the extension spring (located above the horizontal tracks) to help contain the spring if it breaks.
2. Door Balance: Periodically test the balance of your door. If you have a garage door drawbar operator, use the release mechanism so you can operate the door by hand when doing this test. Start with the door in the fully closed position. Lift the door to check its balance.
Adjust TorqueMaster
®
or Extension spring(s), if door lifts by itself (hard to pull down) or if door is difficult to lift (easy to pull down). DO NOT attempt to repair or adjust Torsion Springs yourself. To adjust TorqueMaster
®
or Extension spring(s), refer to your installation instructions and owner’s manual. If in question about any of the procedures, do not perform the work.
Instead, have it adjusted by a trained door systems technician.
3. Lubrication: The door should open and close smoothly. Ensure the door track rollers are rotating freely when opening and closing the door. If track rollers do not rotate freely, clean the door tracks, removing dirt and any foreign substances. Clean and lubricate (use a non-silicon based lubricant) graduated end hinges, center hinge(s), steel track rollers, bearings and torsion spring(s) (torsion spring coil surfaces). DO NOT lubricate plastic idler bearings, nylon track rollers, door track. DO NOT oil a cylinder lock, if actuation is difficult use a graphite dust to lubricate.
Warranty
Limited Warranty
Model 9700
Wayne Dalton, a division of Overhead Door Corporation (“Seller”) warrants to the original purchaser of the Model 9700 (“Product”), subject to all of the terms and conditions hereof, that the Product and all components thereof will be free from defects in materials and workmanship for the following period(s) of time, measured from the date of installation:
LIMITED LIFETIME WARRANTY* on the Product sections against:
• Peeling, cracking, or chalking of the original factory-applied coating on the steel sections of the Product.
• The Product becoming inoperable due to rust-through of the steel skin from the core of the Product section, caused by cracking, splitting, or other deterioration of the steel skin, or due to structural failure caused by separation or degradation of the foam insulation.
• The Product hardware (except springs) and the tracks.
Seller warrants the factory attached overlay material against peeling, cracking, chalking, fading or delamination for a period of TWO (2) YEARS.
Seller warrants those component parts of the Product not covered by the preceding provisions of this Warranty for a period of ONE (1) YEAR.
*Limited Lifetime shall mean as long as the original purchaser owns the house in which the Product is originally installed.
Seller’s obligation under this warranty is specifically limited to repairing or replacing, at its option, any part which is determined by Seller to be defective during the applicable warranty period. Any labor charges are excluded and will be the responsibility of the purchaser.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty is made to the original purchaser of the Product only, and is not transferable or assignable. This warranty applies only to Product installed in a residential or other non-commercial application. It does not cover any Product installed in commercial or industrial building applications. This warranty does not apply to any unauthorized alteration or repair of the Product, or to any Product or component which has been damaged or deteriorated due to misuse, neglect, accident, failure to provide necessary maintenance, normal wear and tear, acts of God, or any other cause beyond the reasonable control of Seller or as a result of having been exposed to toxic or abrasive environments, including blowing sand, salt water, salt spray and toxic chemicals and fumes.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED IN TIME TO THE APPLICABLE WARRANTY PERIOD REFLECTED ABOVE. NO WARRANTIES, WHETHER EXPRESS OR IMPLIED,
WILL APPLY AFTER THE LIMITED WARRANTY PERIOD HAS EXPIRED. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
IN NO EVENT SHALL SELLER BE RESPONSIBLE FOR, OR LIABLE TO ANYONE FOR, SPECIAL, INDIRECT, COLLATERAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, even if Seller has been advised of the possibility of such damages. Such excluded damages include, but are not limited to, loss of use, cost of any substitute product, or other similar indirect financial loss. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Claims under this warranty must be made promptly after discovery, within the applicable warranty period, and in writing to the authorized distributor or installer whose name and address appear below. The purchaser must allow Seller a reasonable opportunity to inspect any Product claimed to be defective prior to removal or any alteration of its condition. Proof of the purchase and/or installation date, and identification as the original purchaser, may be required. There are no established informal dispute resolution procedures of the type described in the Magnuson-Moss Warranty Act.
• SELLER: _______________________________________________________________________
• SELLER’S ADDRESS: _______________________________________________________________________
_______________________________________________________________________
18
Thank you for your purchase.
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE
Please Do Not Return This Product To The Store. Please call 1-866-569-3799 (Press Option 1) and follow the prompts to contact the appropriate customer service agent. They will be happy to handle any questions that you may have.
AFTER INSTALLATION IS COMPLETE, FASTEN THIS
MANUAL NEAR GARAGE DOOR FOR EASY REFERENCE.

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Torsion counterbalance system
- Quick Install Flag Angles
- Fully Adjustable Flag Angles
- Drawbar operator bracket
- Windload Jamb Brackets