advertisement
ROBO Cylinder
RCA2 Actuator
Slider Type
Motor coupling types: SA3C w SA4C w SA5C w SA6C
Motor reversing types: SA3R w SA4R w SA5R w SA6R
Operating Manual
First Edition
IAI America, Inc.
Please Read Before Use
Thank you for purchasing an IAI product.
To ensure safe use of the actuator, be sure to read this operating manual and handle the actuator correctly.
Do not handle or operate the actuator in any way not specified in this operating manual or the operation manual of your controller, by assuming that any such handling/use is prohibited.
[Applicable Models]
ROBO Cylinder RCA2 Actuator
Motor coupling types
• RCA2-SA3C
• RCA2-SA4C
• RCA2-SA5C
• RCA2-SA6C
Motor reversing types
• RCA2-SA3R
• RCA2-SA4R
• RCA2-SA5R
• RCA2-SA6R
• Unauthorized copy, duplication or reproduction of the information provided in this manual, whether in whole or part, is strictly prohibited.
• The information provided in this manual is subject to change without prior notice for the purpose of improvement.
• This manual has been written with due attention to precision and completeness. Should you find any error or if you have any feed back, please contact IAI.
Table of Contents
Replacement of Belt and Motor for Reversing Type (AC Servo Motor: RCA2) ........................ 64
Safety Guide (Read This Section Before Use)
When designing and manufacturing a robot system, ensure safety by following the safety precautions provided below and taking the necessary measures.
1. Regulations and Standards Governing Industrial Robots
Safety measures on mechanical devices are generally classified into four categories under the
International Industrial Standard ISO/DIS 12100, “Safety of machinery,” as follows:
Safety measures Inherent safety design
Protective guards --- Safety fence, etc.
Additional safety measures --- Emergency stop device, etc.
Information on use --- Danger sign, warnings, operation manual
Based on this classification, various standards are established in a hierarchical manner under the
International Standards ISO/IEC. The safety standards that apply to industrial robots are as follows:
Type C standards (individual safety standards) ISO10218 (Manipulating industrial robots – Safety)
JIS B 8433
(Manipulating industrial robots – Safety)
Also, Japanese laws regulate the safety of industrial robots, as follows:
Industrial Safety and Health Law Article 59
Workers engaged in dangerous or harmful operations must receive special education.
Ordinance on Industrial Safety and Health
Article 36 --- Operations requiring special education
No. 31 (Teaching, etc.) --- Teaching and other similar work involving industrial robots
(exceptions apply)
No. 32 (Inspection, etc.) --- Inspection, repair, adjustment and similar work involving industrial robots (exceptions apply)
Article 150 --- Measures to be taken by the user of an industrial robot
1
2. Requirements for Industrial Robots under Ordinance on Industrial
Safety and Health
Work area Work condition
Cutoff of drive source
Measure Article
Signs for starting operation Article 104
Outside movement range
During automatic operation
Not cut off
Installation of railings, enclosures, etc.
Article 150-4
Inside movement range
During teaching, etc.
During inspection, etc.
Cut off (including stopping of operation)
Sign, etc., indicating that work is in progress
Not cut off
Cut off
Preparation of work rules
Measures to enable immediate stopping of operation
Sign, etc., indicating that work is in progress
Provision of special education
Checkup, etc., before commencement of work
To be performed after stopping the operation
Sign, etc., indicating that work is in progress
Preparation of work rules
Not cut off (when inspection, etc., must be performed during operation)
Measures to enable immediate stopping of operation
Sign, etc., indicating that work is in progress
Provision of special education
(excluding cleaning and lubrication)
Article 150-3
Article 150-3
Article 150-3
Article 150-3
Article 36-31
Article 151
Article 150-5
Article 150-5
Article 150-5
Article 150-5
Article 150-5
Article 36-32
2
3. Applicable Models of IAI’s Industrial Robots
Machines meeting the following conditions are not classified as industrial robots according to Notice of
Ministry of Labor No. 51 and Notice of Ministry of Labor/Labor Standards Office Director (Ki-Hatsu No.
340):
(1) Single-axis robot with a motor wattage of 80 W or less
(2) Combined multi-axis robot whose X, Y and Z-axes are 300 mm or shorter and whose rotating
3 part, if any, has the maximum movement range of within 300 mm including the tip of the rotating part
(3) Multi-joint robot whose movable radius and Z-axis are within 300 mm
Among the products featured in our catalogs, the following models are classified as industrial robots:
1. Single-axis ROBO Cylinders
RCS2/RCS2CR-SS8 whose stroke exceeds 300 mm
The following models whose stroke exceeds 300 mm and whose motor capacity also exceeds 80 W:
ISA/ISPA, ISDA/ISPDA, ISWA/ISPWA, IF, FS, NS
3. Linear servo actuators
All models whose stroke exceeds 300 mm
Any robot that uses at least one axis corresponding to one of the models specified in 1 to 3
5. IX SCARA robots
IX-NNN (NNW, NNC) 3515
IX-NNN (NNW, NNC) 50 /60/70/80
IX-NSN5016/6016
IX-TNN (UNN) 3015/3515
IX-HNN (INN) 50 /60/70/80
3
4. Notes on Safety of Our Products
Common items you should note when performing each task on any IAI robot are explained below.
No. Task
1 Model
Note z This product is not planned or designed for uses requiring high degrees of safety. selection Accordingly, it cannot be used to sustain or support life and must not be used in the following applications:
[1] Medical devices relating to maintenance, management, etc., of life or health
[2] Mechanisms or mechanical devices (vehicles, railway facilities, aircraft facilities, etc.) intended to move or transport people
[3] Important safety parts in mechanical devices (safety devices, etc.) z Do not use this product in the following environments:
[1] Place subject to flammable gases, ignitable objects, flammables, explosives, etc.
[2] Place that may be exposed to radiation
[3] Place where the surrounding air temperature or relative humidity exceeds the specified range
[4] Place subject to direct sunlight or radiated heat from large heat sources
[5] Place subject to sudden temperature shift and bedewing
[6] Place subject to corrosive gases (sulfuric acid, hydrochloric acid, etc.)
[7] Place subject to excessive dust, salt or iron powder
[8] Place where the product receives direct vibration or impact z Do not use this product outside the specified ranges. Doing so may significantly shorten the life of the product or result in product failure or facility stoppage.
3 Storage product. z Use appropriate means for transportation. z Do not step on the package. z Do not place on the package any heavy article that may deform the package. z The storage environment should conform to the installation environment. Among others, be careful not to cause bedewing.
4
No. Task
4 Installation/ startup
Note
(1) Installing the robot, controller, etc. z Be sure to firmly secure and affix the product (including its load).
If the product tips over, drops, malfunctions, etc., damage or injury may result. z Do not step on the product or place any article on top. The product may tips over or the article may drop, resulting in injury, product damage, loss of/drop in product performance, shorter life, etc. z If the product is used in any of the following places, provide sufficient shielding measures:
[1] Place subject to electrical noise
[2] Place subject to a strong electric or magnetic field
[3] Place where power lines or drive lines are wired nearby
[4] Place subject to splashed water, oil or chemicals
(2) Wiring the cables z Use IAI’s genuine cables to connect the actuator and controller or connect a teaching tool, etc. z Do not damage, forcibly bend, pull, loop round an object or pinch the cables or place heavy articles on top. Current leak or poor electrical continuity may occur, resulting in fire, electric shock or malfunction. z Wire the product correctly after turning off the power. z When wiring a DC power supply (+24 V), pay attention to the positive and negative polarities.
Connecting the wires in wrong polarities may result in fire, product failure or malfunction. z Be sure to connect the cable connectors without fail and firmly. Failing to do so may result in fire, electric shock or product malfunction. z Do not cut and reconnect the cables of the product to extend or shorten the cables. Doing so may result in fire or product malfunction.
(3) Grounding z Be sure to provide class D (former class 3) grounding for the controller. Grounding is required to prevent electric shock and electrostatic charges, improve noise resistance and suppress unnecessary electromagnetic radiation.
(4) Safety measures z Implement safety measures (such as installing safety fences, etc.) to prevent entry into the movement range of the robot when the product is moving or can be moved. Contacting the moving robot may result in death or serious injury. z Be sure to provide an emergency stop circuit so that the product can be stopped immediately in case of emergency during operation.
5
No. Task
4 Installation/
Note z Implement safety measures so that the product cannot be started only by turning startup on the power. If the product starts suddenly, injury or product damage may result. z Implement safety measures so that the product will not start upon cancellation of an emergency stop or recovery of power following a power outage. Failure to do so may result in injury, equipment damage, etc. z Put up a sign saying “WORK IN PROGRESS. DO NOT TURN ON POWER,” etc., during installation, adjustment, etc. If the power is accidently turned on, electric shock or injury may result. z Implement measures to prevent the load, etc., from dropping due to a power outage or emergency stop. z Ensure safety by wearing protective gloves, protective goggles and/or safety shoes, as necessary. z Do not insert fingers and objects into openings in the product. Doing so may result in injury, electric shock, product damage, fire, etc.
5 Teaching z Whenever possible, perform teaching from outside the safety fences. If teaching must be performed inside the safety fences, prepare “work rules” and make sure the operator understands the procedures thoroughly. z When working inside the safety fences, the operator should carry a handy emergency stop switch so that the operation can be stopped any time when an abnormality occurs. z When working inside the safety fences, appoint a safety watcher in addition to the operator so that the operation can be stopped any time when an abnormality occurs. The safety watcher must also make sure the switches are not operated
6 Confirmation operation inadvertently by a third party. z Put up a sign saying “WORK IN PROGRESS” in a conspicuous location.
* Safety fences --- Indicate the movement range if safety fences are not provided. z After teaching or programming, carry out step-by-step confirmation operation before switching to automatic operation. z When carrying out confirmation operation inside the safety fences, follow the specified work procedure just like during teaching. z When confirming the program operation, use the safety speed. Failure to do so may result in an unexpected movement due to programming errors, etc., causing injury. z Do not touch the terminal blocks and various setting switches while the power is supplied. Touching these parts may result in electric shock or malfunction.
6
No. Task
7 Automatic
Note z Before commencing automatic operation, make sure no one is inside the safety operation fences. z Before commencing automatic operation, make sure all related peripherals are ready to operate in the auto mode and no abnormalities are displayed or indicated.
z Be sure to start automatic operation from outside the safety fences. z If the product generated abnormal heat, smoke, odor or noise, stop the product immediately and turn off the power switch. Failure to do so may result in fire or product damage. z If a power outage occurred, turn off the power switch. Otherwise, the product may move suddenly when the power is restored, resulting in injury or product damage.
8 Maintenance/ z Whenever possible, work from outside the safety fences. If work must be inspection performed inside the safety fences, prepare “work rules” and make sure the operator understands the procedures thoroughly. z When working inside the safety fences, turn off the power switch, as a rule. z When working inside the safety fences, the operator should carry a handy emergency stop switch so that the operation can be stopped any time when an abnormality occurs. z When working inside the safety fences, appoint a safety watcher in addition to the operator so that the operation can be stopped any time when an abnormality
10 Disposal occurs. The safety watcher must also make sure the switches are not operated inadvertently by a third party. z Put up a sign saying “WORK IN PROGRESS” in a conspicuous location. z Use appropriate grease for the guides and ball screws by checking the operation manual for each model. z Do not perform a withstand voltage test. Conducting this test may result in product damage.
* Safety fences --- Indicate the movement range if safety fences are not provided.
9 Modification z The customer must not modify or disassemble/assemble the product or use maintenance parts not specified in the manual without first consulting IAI. z Any damage or loss resulting from the above actions will be excluded from the scope of warranty. z When the product becomes no longer usable or necessary, dispose of it properly as an industrial waste. z When disposing of the product, do not throw it into fire. The product may explode or generate toxic gases.
7
5. Indication of Cautionary Information
The operation manual for each model denotes safety precautions under “Danger,” “Warning,” “Caution” and “Note,” as specified below.
Level Degree of danger/loss Symbol
Danger
Failure to observe the instruction will result in an imminent danger leading to death or serious injury.
Danger
Warning
Failure to observe the instruction may result in death or serious injury.
Warning
Caution
Note
Failure to observe the instruction may result in injury or property damage.
The user should take heed of this information to ensure the proper use of the product, although failure to do so will not result in injury.
Caution
Note
8
Handling Precautions
1. Handling a Single Actuator
Please adhere to the following when handling a single actuator.
1.1 Handling the Packed Unit
Unless otherwise specified, single-axis actuators are shipped in individual packaging.
Please handle packages carefully during transport to ensure that product is not damaged by bumping or dropping.
• Never attempt to move heavy packages by yourself.
• Always set packages down on a level surface.
• Never climb on top of packages.
• Never place heavy objects or objects where the load is concentrated in one place on top of packages, as this may cause deformation.
1.2 Handling the Actuator After Unpacking
Do not carry an actuator by a cable or attempt to move it by pulling the cable.
When unpacking the actuator and handling it thereafter, always hold it by the base.
Never hold an actuator by the stainless sheet.
• Be careful not to bump the actuator into anything when moving it, paying particular care to the side covers.
• Do not attempt to force any part of the actuator. Take particular care not to force the stainless sheet.
Caution: Never hold the actuator by the stainless sheet.
Supplement) For the names of each part of the actuator, refer to 1, "Part Names.”
9
2. Handling the Actuator Assembly
When transporting the actuator with its axes already assembled, take note of the following items.
2.1 Shipping from IAI Already Assembled
After assembly at IAI, your machine undergoes a shipping inspection, is packed in a crate with skids, and finally shipped.
If any of the combined actuators is a slider, the slider is securely fastened in place to prevent unexpected movement during shipping. Combined units have the ends of their actuators fastened so as to prevent them from moving significantly due to external vibration.
• The crate is not designed to withstand dropping or collision. Please handle it carefully. It is also not built to have items stacked on it, so please avoid placing heavy objects on top of the crate.
• When lifting the package using belts or the like, be sure to pass the belts around the reinforcement frames under the skids. The same applies for lifting the package with a forklift; please ensure that the forks are placed under the skids.
• When setting the package down, do not let the package receive an impact upon contacting the floor.
2.2 Handling After Unpacking
Please adhere to the following instructions when handling the assembled unit, whether it was shipped preassembled at IAI or assembled on your site.
• Secure the slider so that it does not move unexpectedly during transport.
• If the end of the actuator is protruding, fasten it down properly so that it does not move significantly due to external vibration. When transporting the assembly without the ends of the actuators fastened, do not subject the assembly to an impact of 0.3 G or more.
• When using belts or the like to lift an assembly consisting of an actuator and peripheral equipment, make sure the belts are not passed around the actuator itself or otherwise do not touch the actuator.
• Make sure the belts support the actuator load by its base by using appropriate cushioning materials.
• Lift the end of the Y-axis with a separate belt, ensuring that the assembly remains level. At this time, also make sure the load is not placed on the screw cover.
• Make sure the load is not placed on the brackets, covers, or connector box.
Also make sure the cables are not pinched or deformed excessively.
10
3. Handling after Assembly with Peripheral Equipment
When the machine assembled at IAI is transported as an assembly, also follow the handling precautions in 2.2, “Handling after Unpacking.”
11
The names of the actuator parts are indicated below.
In this manual, the right and left are determined by viewing the actuator from the top and from the motor side.
Also, the front side means the side opposite from the motor.
● “Motor coupling types”: RCA2-SA3C/SA4C/SA5C/SA6C
Side cover Slider cover
Stainless sheet
Other side
Right Side
Left Side
Motor unit
Slider
* Refer to 2, “External Dimensions” for details.
● “Motor reversing types”: RCA2-SA3R/SA4R/SA5R/SA6R
Slider cover
Stainless sheet
Right Side
Slider
Other side
Connector
Left Side
Motor unit
* Refer to 2, “External Dimensions” for details.
Connector
Motor side
Reversing bracket
Motor side
12
2.1 RCA2-SA3C
13
2.2 RCA2-SA3C- with Slider Cover
14
2.3 RCA2-SA4C
15
2.4 RCA2-SA4C- with Slider Cover
16
2.5 RCA2-SA5C
17
2.6 RCA2-SA5C- with Slider Cover
18
2.7 RCA2-SA6C
19
2.8 RCA2-SA6C- with Slider Cover
20
2.9 RCA2-SA3R, Reversing to Left (Right)
21
2.10 RCA2-SA3R- with Slider Cover, Reversing to Left (Right)
22
2.11 RCA2-SA4R, Reversing to Left (Right)
23
2.12 RCA2-SA4R- with Slider Cover, Reversing to Left (Right)
24
2.13 RCA2-SA5R, Reversing to Left (Right)
25
2.14 RCA2-SA5R- with Slider Cover, Reversing to Left (Right)
26
2.15 RCA2-SA6R, Reversing to Left (Right)
27
2.16 RCA2-SA6R- with Slider Cover, Reversing to Left (Right)
28
3.1 ASEP Controller Cables
Integrated motor/encoder cable
(CB-APSEP-MPA***)
*** indicates the cable length (L). Up to 10 m can be specified.
Example) 080 = 8 m
[1][2]
[5] [6]
Model Nameplate
Lot number
[3][4]
No. Item
D-1100D 1-1827863-1
1 Housing
2 Contact
(black, 2.0-mm pitch, 22 poles)
D-1 1827570-2 (AWG 22 to 18, 1.08 to 1.6
∅)
3 Housing
4 Contact SPND-001T-C0.5 (AWG 26 to 22, 1.0 to 1.5
∅)
Manufacturer
AMP
JST
6 ZUL2854-OHFRPCVVSW
TMS-4ZB008
25AWG x 6P + 25AWG x 2C + 22AWG x 6C,
TS08V0350
TATSUTA ELECTRIC
WIRE & CABLE
TATSUTA ELECTRIC
WIRE & CABLE
Terminal number on actuator side
Wiring diagram
Black
White
Brown
Green
Yellow
Red
Orange
Gray
White
Yellow
Green
Black
Brown
Black
(identification tap
Brown
(identification tape)
Green
(identification tape)
Red
(identification tape)
White
(identification tape)
Yellow
(identification tape)
Shield
Terminal number on controller side
29
3.2 ACON, ASEL Controller Cables
RCA2 Integrated motor/encoder cable
(CB-ACS-MPA***)
[1][2]
[7] Model Nameplate
No. Item
[1] Receptacle housing D-1100D 1-1827863-1
[2] Receptacle contact
[3] Socket
D-1 1827570-2
DF1E-3S-2.5C
[5] Housing
[6] Contact
DF1E-2022SCF
PHDR-18VR
SPHD-001T-P0.5
[7] UL2854-VVSWKA
*** indicates the cable length (L). Up to 10 m can be specified.
Example) 080 = 8 m
TS06V1200 (25AWG x 7P + 22AWG x 6C)
[7]
[3][4]
[5][6]
Manufacturer
AMP
AMP
Hirose
Hirose
JST
JST
TATSUTA ELECTRIC
WIRE & CABLE
Terminal number on actuator side
[1]
Wiring diagram [Signals]
Red
Yellow
Black
Yellow (Red
•)
Yellow (Blue
•)
Pink (Red
•)
Pink (Blue
•)
White (Red
•)
White (Blue
•)
Orange (Red
•)
Orange (Blue
•)
Gray (Red
•)
Gray (Blue
•)
Orange (Red/continuou
Orange (Blue/continuous)
Gray (Red/continuous)
Gray (Blue/continuous)
Terminal number on controller side
[3]
[5]
(Shield)
30
4. Options
The brake is a mechanism designed to prevent the slider from dropping on a vertically installed actuator when the power or servo is turned off.
Use the brake to prevent the installed load, etc., from being damaged due to the falling slider.
As shown in the table below, the maximum load current of the standard specification and high acceleration/deceleration specification can be lowered. For details, refer to the section on power capacity in the manual for your ACON/ASEL controller.
Model
Standard specification /
High acceleration/deceleration specification
Maximum load current
Energy-saving measure
Maximum load current
SA3, SA5 4.4 A 2.5 A
SA6
SA4
4.0 A
5.1 A
2.2 A
3.4 A
You can specify an option to order your actuator without side covers.
(For the external dimensions with and without side covers, refer to 2, “External Dimensions.”)
The standard home position is on the motor side. However, you can specify an option to reverse the motor position if it is desirable in view of the layout of the system, etc.
(Note) The home position is adjusted at the factory before shipment. If you wish to change the home after the delivery of your actuator, you must return the actuator to IAI for adjustment.
31
5. Checking after Unpacking
After unpacking, check the product condition and the included items.
No. Item
1 Actuator
Remarks
Refer to 5.3, “How to Read Model Nameplate” and 5.4, “How to Read Model.”
Accessories
2
3
4
RCA integrated motor/encoder cable
First Step Guide
Operating Manual (CD)
CB-APSEP-MPA : ASEP type
CB-ACS-MPA : ACON, ASEL type
5.2 Operation Manuals Relating to This Product
No. Name Control
1 Operation Manual for ASEL Controller
2 Operation Manual for ACON-C/CG/CF Controller
MJ0165
MJ0176
3 Operation Manual for ACON-CY Controller
4 Operation Manual for ACON-SE Controller
5 Operation Manual for ACON-PL/PO Controller
6 Operation Manual for ASEP Controller
MJ0167
MJ0171
MJ0166
MJ0216
7
8
9
Operation Manual for PC Software RCM-101MW/RCM-101-USB
Operation Manual for Teaching Pendant CON-T/TG
Operation Manual for Dedicated ASEP/PSEP Touch Panel Teaching
SEP-PT
10 Operation Manual for Simple Teaching Pendant RCM-E
11 Operation Manual for Data Setter RCM-P
12 Operation Manual for Touch Panel Display RCM-PM-01
MJ0155
MJ0178
MJ0217
MJ0174
MJ0175
MJ0182
5.3 How to Read Model Nameplate
Model
Serial number
32
5.4 How to Read Model
<Series name>
<Type>
Motor coupling types
SA3C
SA4C
SA5C
SA6C
Motor reversing
SA3R
SA4R
SA5R
SA6R
<Encoder type>
I: Incremental
<Motor type>
10 (10 W): SA3C, SA3R
20 (20 W): SA4C, SA4R
30 (30 W): SA6C, SA6R
<Option>
B: Brake type
LA: Power-saving measure
NCO: No-cover specification
NM: Reversed-home specification
<Cable length>
N: None
M: 5 m
X : Specified length
<Applicable controller>
A1: ASEL
ACON-C/CG
ACON-C/CG
ACON-CY
ACON-SE
ACON-PL/PO
A3: ASEP
<Stroke>
<Lead>
SA3C, SA3R
2/4/6
SA4C, SA4R
2.5/5/10
SA5C, SA5R
3/6/12
SA6C, SA6R
3/6/12
33
6. Specifications
SA6
Lead mm 2 4 6 2.5
5 10 3 6 12 3 6 12 3 6 12 mm/sec 100 200 300 125 250 500 150 300 600 150 300 600 135 270 540
Max horizontal loading capacity kg 3 2 1 6 4 2 8 6 3 12 8 5 12 8 5
Max vertical loading capacity kg 1.5 1 0.5
50-300
Stroke mm
(per 50)
3 1.5
50-400
(per 50)
1 3 1.5
1 4 2 1.5 4 2 1.5
50-500
(per 50)
50-550
(per 50)
600
Rated output W
Load moment
N 85 43 28 136 68 34 68 34 17 105 53 26 105 53 26
Ma: 1.96 (0.2) Ma: 3.04 (0.31) Ma: 3.92 (0.40) Ma: 4.31 (0.44) Ma: 4.31 (0.44)
N·m
(kgf·cm)
Mb: 2.84 (0.29) Mb: 4.31 (0.44) Mb: 5.58 (0.57) Mb: 6.17 (0.63) Mb: 6.17 (0.63)
Mc: 3.14 (0.32) Mc: 5.00 (0.51) Mc: 8.53 (0.87) Mc: 10.98 (1.12) Mc: 10.98 (1.12)
5,000 km service life
Positioning repeatability ±mm
*) Maximum speed may not be reached on all strokes.
*) Maximum loading capacity depends on operating conditions.
0.05
34
[1] Maximum speed, loading capacity
Determine which models you can choose from by the maximum speed and loading capacity.
• AC servo motor (Graph 1)
How to decide: If your maximum speed and loading capacity are within the usage range in the graph, you can use the model.
35
Graph 1 Servo Motor: RCA2
Horizontal
Correlation of speed and loading capacity
(Horizontal)
Lead 2
Lead 4
Speed (mm/sec)
Lead 6
Correlation of speed and loading capacity
(Horizontal)
Lead 2.5
Lead 5
Speed (mm/sec)
Correlation of speed and loading capacity
(Horizontal)
Lead 3
Lead 6
Lead 12
Speed (mm/sec)
Lead 10
Correlation of speed and loading capacity
(Horizontal)
Lead 3
Lead 6
Speed (mm/sec)
Lead 12
Vertical
Correlation of speed and loading capacity
(Vertical)
Lead 2
Lead 4
Speed (mm/sec)
Correlation of speed and loading capacity
(Vertical)
Lead 2.5
Lead 5
Speed (mm/sec)
Correlation of speed and loading capacity
(Vertical)
Lead 3
Lead 6
Speed (mm/sec)
Correlation of speed and loading capacity
(Vertical)
Lead 3
Lead 6
Speed (mm/sec)
Lead 6
Lead 10
Lead 12
Lead 12
36
8. Installation Environment and Storage Environment
Install the actuator in an environment meeting the following conditions:
• Not exposed to direct sunlight
• The machine does not receive radiated heat from large heat sources such as heat treatment furnaces.
• Surrounding air temperature of 0 to 40°C
• Humidity of 85% or below, non-condensing
• Not subject to corrosive or flammable gases
• Is a normal environment for assembly work where there is not much dust.
• Not subject to oil mist or cutting fluid
• Not subject to impact or vibration
• Not subject to significant electromagnetic waves, ultraviolet light or radiation
• This product is not designed to provide chemical resistance.
In general, the environment shall be one where the operator can work without wearing protective gears.
Open space required for maintenance inspection
The storage environment should conform to the installation environment. Particularly when the actuator is stored for a long period of time, give consideration to prevent bedewing.
Unless specified, the actuator is shipped without any drying agent placed in the package. If the actuator is stored in an environment subject to bedewing, implement anti-bedewing measures over the entire package or directly on the actuator after unpacking.
The maximum storage temperature is 60
°C for a short period. If the storage period exceeds 1 month, make sure the storage temperature dose not exceed 50
°C.
37
9. Installation
The actuator mounting surface should be machined or otherwise processed to a smooth surface of equivalent precision.
9.1 Installation of Actuator
This actuator contains installation tap holes which allow it to be secured from the rear.
(Note that tap hole size depends on model. Please see diagrams below and external dimensions.)
The actuator also contains reamed holes for use with positioning pins.
Slider type
Model
Tap size and maximum screw-in depth
Applicable bolt
Tightening torque
Bolt bearing surface is steel
Bolt bearing surface is aluminum
A (mm) Reamed hole (mm)
SA3 M3, depth 5
SA4 M3, depth 5
SA5 M4, depth 7
SA6 M5, depth 8
M3
M3
M4
M5
1.54 N-m (0.16 kgf-m) 0.83 N-m (0.085 kgf-m)
1.54 N-m (0.16 kgf-m) 0.83 N-m (0.085 kgf-m)
3.59 N-m (0.37 kgf-m)
7.27 N-m (0.74 kgf-m)
1.76 N-m (0.18 kgf-m)
3.42 N-m (0.35 kgf-m)
17
21
26
31
∅2H7, depth 4 from bottom face of base
∅2.5H7, depth 5 from bottom face of base
∅2.5H7, depth 5 from bottom face of base
∅3H7, depth 5 from bottom face of base
38
Tightening screws
• Use hexagonal socket head bolts for the male threads for installing the base.
• Use of high-tension bolts meeting at least ISO 10.9 is recommended.
• For the effective engagement length between the bolt and female thread, provide at least the applicable value specified below:
Female thread is made of steel material
→ Same length as the nominal diameter
Female thread is made of aluminum
→ Twice the nominal diameter
Caution: Be careful when selecting the bolt length. If bolts of inappropriate lengths are used, the tapped holes may be damaged, actuator mounting strength may become insufficient, or contact with driving parts may occur, resulting in lower precision or unexpected accidents.
39
• Mount on a strong, rigid structure to prevent vibration.
• Install the main unit only on a machined surface, or other surface that is highly flat, within ±0.05 mm/m.
• Provide adequate space around the device to allow for future maintenance.
• The side and bottom faces of the base provide reference surfaces for slider travel. When it is necessary that the slider moves in a highly precise fashion, ensure that the device is installed at the direction that is based on the position of these surfaces.
Reference surface
Reference surface
Slider type
Caution: Because the side and bottom faces of the base provide reference surfaces for slider travel as shown in the above diagram, conduct installation based on the position of this side when precision is required.
Follow the diagram below when installing the device using the reference surface.
Model Length of A (mm)
R0.3 or less
Slider type 2 to 4 or less
40
9.3 Installation of the Load
• Please attach the load to the device using the tap holes in the slider.
• The process for attaching these to the main unit is similar to the installation process of the main unit. Use of high-tension bolts meeting at least ISO-10.9 standard is recommended for mounting.
The table below shows the recommended tightening torque.
• There are two reamed holes on the slider, so if you need to be able to secure and detach the load multiple times, please use these holes. Also, if you require precision in your attachment, such as a right angle, use one of the reamed holes to make fine adjustments.
* When using reamed holes, we recommend using an H7 pin. Also, do not force the pin into the hole. Instead, press it gently in until it fits.
• For exact thread depth and reamed hole depth, please see the table below.
Do not screw in pins deeper than indicated in the table below, as this can damage the tap holes, resulting in insecure installation of the load, reduced precision of device, and possible accidents.
Model A B C D
Mounting screw
E
Nominal thread size Tightening torque
∅2H7,
SA3 17 11 17 depth 5
SA4 20 14 21
∅2.5H7, depth 5
M3 D6
M3 D6
M3
M3
0.83 N-m
(0.085 kgf-m)
0.83 N-m
(0.085 kgf-m)
SA5 26 14 22
∅2.5H7, depth 5
SA6 31 15 25
∅3H7, depth5
M4 D8
M5 D10
M4
M5
1.76 N-m
(0.18 kgf-m)
3.42 N-m
(0.35 kgf-m)
41
10. Connecting with Controller
Both for the controller itself and for the connection cable between the controller and actuator (RCA2), use a dedicated IAI controller and dedicated connection cable.
This section explains the wiring method for a single axis.
• If the dedicated connection cable cannot be secured, reduce the load on the cable by allowing it to deflect only by the weight of the cable or wire it in a self-standing cable hose, etc., having a large radius.
• Do not cut and reconnect the dedicated connection cable for extension or shorten the cable.
• Do not pull on the dedicated connection cable or bend it forcibly.
Please consult with IAI if you require a different kind of cable than the one supplied.
RCA2-xx Dedicated connection cable
(connects controller and RCA2)
Dedicated controller y ASEP r=68 mm min. (unfastened) r=34 mm min. (fastened)
Dedicated connection cable y Servo motor cable: CB-APSEP-MPA***
*) *** indicates the cable length. Up to 10 m can be specified.
Example) 080 = 8 m
42
Dedicated connection cable
(connects controller and RCA2) r=84 mm min. (unfastened) r=42 mm min. (fastened)
Dedicated controller y ASEL y ACON
Dedicated connection cable y Servo motor cable: CB-ACS-MPA***
*) *** indicates the cable length. Up to 10 m can be specified.
Example) 080 = 8 m
43
When building an application system using the actuator and controller, incorrect wiring or connection of each cable may cause broken wire, poor contact or other unexpected problem. The prohibited items relating to cable wiring are explained below.
• Do not cut and reconnect the cable for extension or shorten the cable.
• If the cable cannot be secured, reduce the load on the cable by allowing it to deflect only by the weight of the cable or wire it in a self-standing cable hose, etc., having a large radius.
• Prevent the cable from bending at the same point.
• Do not let the cable bend, kink or twist.
• Do not pull the cable with a strong force.
Steel band
(piano wire)
Bundle loosly.
• Do not let the cable receive a turning force at a single point.
• Do not pinch, drop a heavy object onto or cut the cable.
44
• When fixing the cable, provide a moderate slack and do not tension it too tight.
Do not use a spiral tube where the cable flexes frequently.
• Separate the IO and communication lines from the power and drive lines. Do not wire them together in the same duct.
Power line
Duct
I/O lines
(flat cable)
• Pay attention to the following points when using a cable track.
• Do not let the cable get tangled or kinked in a cable track or flexible tube. When bundling the cable, keep a certain degree of flexibility (so that the cable will not become too taut when bent).
• Do not cause the cables to occupy more than 60% of the space in the cable track.
Cable track
Cable
Warning
z Always turn off the controller power before connecting/disconnecting cables. If cables are connected/disconnected while the power is still supplied, the actuator may malfunction and a serious injury or equipment damage may occur. z Loose connectors may cause the actuator to malfunction and create a dangerous situation. Be sure to confirm that all connectors are securely connected.
45
11. Notes on Operation
11.1 Placing a Load on the Actuator
y Do not exceed the load ratings given in the specification table below.
In particular, be careful not to exceed the load moment, extension load length, and maximum loading capacity for the slider.
(See diagram below.) y Allowable load moment Unit: N·m (kgf·m)
SA3
SA4
1.96 (0.2)
3.04 (0.31)
2.84 (0.29)
4.31 (0.44)
3.14 (0.32)
5.00 (0.51)
8.53 (0.87)
SA6 4.31 (0.44) 6.17 (0.63) 10.98 (1.12)
Make sure that the load on the table front plate does not exceed the moment Ma if operating a slider type.
When calculating the load moment, see 11.1.1, "Positioning the guide to calculate the load moment" below.
Load moment direction
"Slider type"
46
Model
SA3
SA4
SA5
SA6
Extension load length direction
Mb, Mc direction
Allowable extension lengths
Ma direction
100 mm or less
120 mm or less
130 mm or less
150 mm or less
Mb direction
100 mm or less
120 mm or less
130 mm or less
150 mm or less
Ma direction
Mc direction
100 mm or less
120 mm or less
130 mm or less
150 mm or less
47
11.1.1 Positioning the guide to calculate the load moment
When calculating the load moment, please take the following operating positions into account.
“Slider type”
Ma, Mc moment
Offset base position
A (mm) 29.5 36.5 43.5 47
Caution: Application of an excessive load moment may produce unwanted results such as a shorter life of the guide. Also note that using the actuator with an extension load exceeding the allowable limit may generate vibration or negatively affect the life of the guide.
48
11.1.2 Thrust direction external force
Be careful not to subject the actuator to external force or impact load in the thrust direction in excess of allowable capacity.
Subjecting the actuator to levels of external force or impact load above the allowable capacity may damage or destroy internal components.
Thrust direction external force capacity Unit: N (kgf)
"Slider type"
Thrust direction
49
11.2 Adjusting the Home Position
The actuator home position can be adjusted by changing parameter
*1
. In order to make adjustments, please do the following.
[1] Verify the home position by performing a home return operation.
[2] Move the actuator to the desired position, verify the distance between the old and new positions, and adjust the parameter accordingly. The parameter can be set to a positive value in the direction of movement. (It cannot be set to a negative value.)
[3] Increasing the offset amount restricts the movement range by the amount of the increase. If you set an offset greater than 1 mm, please reset the stroke soft limit.
*1 ACON controller:
ASEL controller:
ASEP controller:
No. 22, home return offset distance
Parameter No. 12 for each axis, home preset value
No. 16, home return preset value
11.3 Changing the Home Position Direction
To change the home position direction after delivery, it is necessary to change the movement direction parameter. Please contact with IAI if you need to do this.
Warning:
The encoder serves not only to detect the actuator’s position and the home position signal, it also plays a crucial role in phase switching for the AC servo power line, and its phase is adjusted precisely. Never touch the encoder in order to change the home position.
50
11.4 Stainless Sheet Section
• The stainless sheet is attached by adsorption to the side cover. If the environment contains high levels of iron filings or other magnetic matter, this may become adsorbed between the stainless sheet and the rubber and cause malfunction. For that reason, avoid usage in such an environment.
• Keep adhesive, paint, and other viscous material off the stainless sheet. Such material sticking to the stainless sheet can lead to defective slider operation and stainless sheet damage.
• Be careful to avoid localized force on the stainless sheet. Such force could deform the stainless sheet and cause malfunctions.
Also, during installation and transport, do not hold on to or press on the stainless sheet. Doing so could damage the stainless sheet.
51
12.1 Inspection Items and Timing
Follow the maintenance inspection schedule below.
It is assumed that the equipment is operating 8 hours per day.
If the equipment is running continuously night and day or otherwise running at a high operating rate, inspect more often as needed.
External visual inspection Internal inspection Greasing
Start of work inspection
1-month inspection
6-month inspection
12-month inspection
{
{
{ {
{ {
Every 6 months thereafter
Every 12 months thereafter
{
{
{ { {
12.2 External Visual Inspection
An external visual inspection should check the following things.
Main unit
Loose actuator mounting bolts, other loose items, buildup
Stainless sheet Scratches
Overall Irregular noise, vibration y As a rule of thumb, the stainless sheet should last for about 5000 km of slider motion. However, under certain conditions, the stainless sheet may need to be replaced earlier.
Generally, replacing the stainless sheet will require that you bring the unit to our plant or have one of our technicians come to your plant to perform the replacement. y If the actuator is installed vertically, certain conditions may cause grease to drip from the guide. Please ensure that proper cleaning is performed and grease is replenished.
12.3 Cleaning
y Clean exterior surfaces as necessary. y Use a soft cloth to wipe away dirt and buildup. y Do not blow too hard with compressed air as it may cause dust to get in through the gaps. y Do not use oil-based solvents as they can harm lacquered and painted surfaces. y To remove severe buildup, wipe gently with a soft cloth soaked in a neutral detergent or alcohol.
52
Turn off the power and inspect visually after turning up or removing the stainless sheet in the case of stainless sheet types. With reversing types, inspect visually after removing the reversing bracket.
When inspecting the interior, check the following items.
Main unit Loose mounting bolts, other loose items
Guide section Lubrication, buildup
Belt
(Reversing type)
Belt wear, damage
Visually inspect the interior of the equipment. Check whether dust or other foreign matter has gotten inside and check the lubrication state.
The lubrication may have turned brown. This is not a problem as long as the travel surfaces shine as though they are wet.
If the grease is mixed with dust and does not have a shiny appearance, or if the grease has lost its efficacy due to prolonged use, then clean each section and reapply grease.
The procedure for internal inspections is outlined below. Refer to 12.7 for inspection and adjustment of the belt.
"Slider type" --- Steps [2] through [5] are only necessary if the cover is attached. If you do not have a cover, only do step [1].
[1] Move the slider to the home position side.
[2] Remove the cover.
[3] Remove the sheet retainer screws.
[4] Peek under the stainless sheet and check the interior.
[5] When the checks are completed, reassemble the parts by following the same procedure in reverse.
.
Cautions for attached cover:
When checking inside the equipment, be careful not to forcibly bend the stainless sheet or scratch it.
Do not tug on the stainless sheet or in any way attempt to reposition it.
If the sheet is repositioned, it may not be even which may shorten its service life. Should this happen, adjust the stainless sheet by referring to the replacement instructions.
Keep in mind that the edges of the stainless sheet can cause injuries. Always wear gloves when working on it.
53
y Use a soft cloth to wipe away dirt and buildup. y Do not blow too hard with compressed air as it may cause dust to get in through the gaps. y Do not use oil-based solvents, neutral detergent or alcohol.
12.6.1 Applicable greases for guide
The grease initially used is lithium-based grease.
IAI uses the following grease in our plant.
Idemitsu Kosan Daphne Eponex Grease No. 2
Other companies also sell similar types of grease. For details, give the above grease name to the manufacturer you want to purchase from and ask what corresponding product they have available.
Here are some examples of similar products.
Showa Shell Oil Albania Grease No. 2
Mobil Oil Mobilax 2
Warning:
Never use anything other than synthetic poly-
α olefin grease. Mixing poly-α grease with other grease not only reduces the performance of the grease, it may even cause damage to the actuator.
12.6.2 Applicable greases for ball screw
The grease initially used is lithium-based grease.
IAI uses the following grease in our plant. (Excludes SA3C type)
Kyodo Yushi Multitemp LRL 3
* RCA2 SA3C type uses the following grease.
Idemitsu Kosan Daphne Eponex Grease No. 2
54
12.6.3 How to apply grease
When side cover and stainless sheet are present, remove these before beginning.
Pinch in the direction of the arrows to remove ball screw cover
Ball screw cover
(1) For the guide section, apply the grease by moving the slider back and forth and spreading it out, either by pushing a scraper between the slider and base or by lubricating with a grease injector.
Grease the guides on both sides.
When complete, wipe away any excess grease.
55
(2) To grease ball screws, first clean, then put some grease on your finger and apply while moving the slider back and forth.
When finished, wipe off excess grease.
If the side cover and stainless sheet are present, put them back on.
Note: When moving the slider back and forth by hand, be certain never to apply force in excess of the thrust direction external force capacity (see 11.1.2). (If the slider will not move, operate it using a jog function.)
56
12.7 Belt
12.7.1 Inspection of belt
When inspecting the belt, remove the pulley cover and check the belt visually.
Although the durability of the belt is affected significantly by the operating conditions, generally a belt has a flex line of several million times.
As a reference for determining when to actually replace the belt, replace the belt if any of the following conditions is found:
• Significant wear of the teeth or end face of the belt
• Swelling of the belt due to attached oil, etc.
• Cracking or other damage of the teeth or back of the belt
• Breaking of the belt
12.7.2 Applicable belt
Manufacturer: Bando Chemical Industries, Ltd.
Belt model (type)
40S2M138R, 4-mm wide (clean rubber type)
60S2M152R, 6-mm wide (clean rubber type)
60S2M180R, 6-mm wide (clean rubber type)
60S2M180R, 6-mm wide (clean rubber type)
12.7.3 Adjustment of belt tension
Model
SA3R
SA4R
SA5R
SA6R
Remove the pulley cover, loosen the tension adjustment bolts (4 locations), and shift the motor as shown below to tension the belt. When finished, tighten the tension adjustment bolts.
Tension
± 0.1 kgf
Other than SA3R: 2.5
± 0.1 kgf
Tension adjustment bolt
Model
Nominal thread size
Tightening torque
SA3R M2.6
SA5R/SA6R M4
0.46 N-m
(0.047 kgf-m)
0.83 N-m
1.76 N-m
(0.18 kgf-m)
57
12.8 Stainless Sheet Replacement (for models with slider cover)
It is possible to replace the stainless sheet without removing the slider cover.
[Items required for replacing the stainless sheet] y Replacement stainless sheet y Hex wrench set y Cellophane
[Part names]
Stainless sheet retainer plates
Stainless sheet Slider cover
[Procedure]
[1] With a 1.5 mm hex wrench, remove the four screws securing the stainless sheet and the two stainless sheet retainer plates.
[2] Pull out the old stainless sheet.
58
[3] Apply cellophane tape to one side of the new stainless sheet.
Cellophane tape
Stainless sheet
Stainless sheet
Apply the cellophane tape as though sandwiching the stainless sheet, leaving about 3 mm of tape sticking out from the stainless sheet. Cut off the excess tape.
[4] Slide the stainless sheet, taped end first, in through the gap under the slider cover.
Do not let stainless sheet fall in this hole.
[5] Fasten the two stainless sheet retainer plates with the four screws. Use a 1.5 mm hex wrench.
Two grooves are cut into the main unit to serve as guides for attaching the stainless sheet. Install the stainless sheet so that it comes to the center of the two grooves. Be careful not to install it in a position where it bends.
[6] After fastening the stainless sheet retainer plate, move the slider by hand a full stroke and ensure that the stainless sheet neither floats up nor is warped. If there is a problem, go back to step [5].
Note: When moving the slider back and forth by hand, be certain never to apply force in excess of the thrust direction external force capacity (see 11.1.2). (If the slider will not move, operate it using a jog function.)
59
12.9
Replacement of Motor (AC Servo Motor: RCA2)
* Refer to 12.10 for the reversing type.
[Items required for replacing the motor] y Replacement motor unit
Axis type
Without brake
Model
With brake
RCA2
(brown encoder cable connector)
Slider type y Hex wrench set y Dedicated replacement jig
(Optional)
RCA2-JG-1 RCA2-SA3
RCA2-JG-2 RCA2-SA4
RCA2-JG-3 RCA2-SA5/SA6
[Procedure]
[1] Disconnect the cable from the motor unit, then use a 2 mm hex wrench to remove the screw which holds together the actuator unit and the motor unit.
Disconnect the cable.
[2] Detach the motor unit.
Actuator-motor unit connecting screw
60
[3] Take out the coupling hub and coupling spacer from the detached motor unit. Twist the coupling hub or coupling spacer on the motor side to align the screw holes with the hole for the tool to go through.
Then remove two screws with a 2 mm hex wrench.
* If there is only a coupling hub on the motor unit side, then there is a coupling spacer on the actuator side which can be removed by pulling.
* If both coupling hub and coupling spacer are present, pull them apart.
(They should separate with a gentle pull.)
Pull apart
Coupling hub
Hole for tool
Coupling spacer
[4] Fit the protruding part of the coupling hub into the groove of the replacement jig (large), and temporarily hold them together with two M 3x3 Allen screws (tighten just enough so that the coupling hub does not fall off).
Replacement jig (large)
Line up holes in center
[5] Turn the shaft to move the slider about 0.5 mm to 1 mm from the mechanical end on the home position side.
[6] Fit the groove of the replacement jig assembled in [4] over the protrusion of the actuator.
Fit groove over protrusion
61
[7] Align the marking on the motor shaft with the point indicated and insert the replacement motor unit into the actuator.
Motor shaft
Top view
Alignment mark
[8] Take out the motor unit and the replacement jig (large). (Do not allow the jig to turn.)
[9] In order to keep the jig from turning, draw a mark using a pen or marker.
[10] Insert the replacement jig (small) in such a way that its protrusion is aligned with the groove in the motor shaft.
Replacement jig (small)
62
[11] Turn the replacement jig (large) and the replacement jig (small) by the same amount. When the coupling fastening screws appear through the tool holes, tighten them with a 2 mm hex wrench.
(There are two fastening screws.)
Tighten with hex wrench
Rotate same amount to keep aligned
[12] Align the marks made in [9]. After the marks are aligned, remove the replacement jig (large) and the replacement jig (small).
[13] Apply the specified grease (TL101Y grease made by NOK) to the coupling spacer (front and rear), then install the coupling spacer on the actuator side.
[14] Install the replacement motor unit on the actuator side, then tighten the fastening screws with a 2 mm hex wrench.
(The actuator side groove and replacement motor unit protrusion should have been aligned in [12], but if not, align them here.)
Tighten with hex wrench
63
12.10 Replacement of Belt and Motor for Reversing Type (AC Servo Motor: RCA2)
[Items required for replacing the motor] y Replacement motor unit of reversing type
Axis type
Without brake
Model
With brake
RCA2
(brown encoder cable connector)
Slider type y Belt
Manufacturer: Bando Chemical Industries, Ltd.
Belt model (type) Model
40S2M138R, 4-mm wide(clean rubber type) SA3R
40S2M152R, 6-mm wide (clean rubber type)
40S2M180R, 6-mm wide (clean rubber type)
SA4R
SA5R
40S2M180R, 6-mm wide (clean rubber type) SA6R gauge y Hex wrench set
[Procedure]
[1] Remove the pulley cover.
Remove the mounting screws. (2 pcs for the SA3R, 3 pcs for other models)
Model Nominal Applicable Allen thread size wrench
SA3R/SA4R M2.5 1.5 mm across flats
SA5R/SA6R
Mounting screw
M3 2 mm across flats
[2] Loosen the tension adjustment bolts (4 pcs) and slacken the belt.
Tightening adjustment bolt
SA3R thread size
M2.6 2 mm across flats
SA4R
SA5R/SA6R
M3
M4
2.5 mm across flats
3 mm across flats
64
[3] Remove the belt from the pulleys. When replacing the belt, proceed to step [7].
[4] Remove the tension adjustment bolts and pull out the motor unit.
[5] Install the replacement motor unit.
As shown below, install the motor unit by making sure its specified surface faces the actuator base.
Loosely secure the motor unit using the tension adjustment bolts.
Install the motor unit by making sure the base surface of the actuator faces the motor unit surface with two holes.
The surface with no gaps should face the motor unit surface with two holes.
65
[6] Move the slider or table by 0.5 to 1 mm from the mechanical end on the home side.
[7] Move the motor unit in the direction of the arrow shown below, and then install the belt.
Align the motor unit with the countermark on the actuator.
When replacing the belt, install the replacement belt.
[8] Pass around the base of the motor unit a strong string (or long tie band) that has been looped, and pull the loop with a tension gauge. When the specified tension is achieved, tighten the tension adjustment bolts uniformly.
Tension
Tension gauge
± 0.1 kgf
Other than SA3R: 2.5
± 0.1 kgf
Tension adjustment bolt
Model Nominal thread size Tightening torque
SA3R M2.6
0.46 N xm
(0.047 kgf xm)
SA4R M3
0.83 N xm
(0.085 kgf xm)
SA5R/SA6R M4
1.76 N xm
(0.18 kgf xm)
66
[9] Install the pulley cover.
Mounting screws
(2 pcs for the SA3R, 3 pcs for other models)
[10] Connect a PC or teaching pendant to the controller and perform a home return.
Check for displacement with the original home position and if there is a displacement, make correction using the following parameter:
ACON Parameter No. 22: Home return offset distance
ASEL Parameter No. 12: Home preset value
If your actuator is of the absolute encoder specification, perform a home return after the parameter has been changed, and then execute an absolute reset.
67
13. Warranty
The actuator you have purchased passed IAI's strict shipping inspection.
The warranty information is provided below.
(1) Warranty period
One of the following periods, whichever expires first:
• 18 months after shipment from IAI
• 12 months after delivery to the specified location
• 2,500 hours of operation
(2) Scope of warranty
The warranty covers only the purchased and delivered IAI product.
If any failure is found during the warranty period despite use in appropriate conditions and such failure is clearly attributable to IAI, IAI will provide a replacement or repair the defective product free of charge.
However, failures due to the following causes are excluded from the scope of warranty:
[1] Handling or use in any condition or environment not specified in the catalog, operation manual, etc.
[2] Anything other than IAI's product
[3] Modification or repair not performed by IAI or its agent
[4] Not foreseeable at the science and technology standards available at the time of shipment from
IAI
[5] Act of God, natural disaster, accident or any other cause beyond IAI's control
[6] Natural discoloration of paint or other aging
[7] Wear of consumable parts (stainless sheet, etc.)
[8] Sound or other subjective feeling not affecting the facility
Take note that the warranty specified herein covers only the delivered product. Any losses arising from a failure of the delivered product are excluded from the scope of warranty.
The defective product is delivered to IAI for repair service.
(3) Limited liability
IAI shall under no circumstance be held liable for any special, indirect or passive losses arising from its product.
(4) Scope of service
The price of the delivered product does not include the costs of programming, dispatching engineers, etc.
Accordingly, separate fees are charged for the following services even during the warranty period:
• Guidance of installation and adjustment, and witnessing of test operation
• Maintenance and inspection
• Technical guidance and training relating to operating methods, wiring methods, etc.
• Technical guidance and training relating to programming and other matters relating to programs
• Other services and tasks that are deemed subject to fees by IAI
68
Revision Date
April 2009 First edition
Description of Revision
69
Appendix
Using the home position marks
As necessary, affix these marks to the product to mark the home position of the actuator.
Example
Stickers Included
Home position mark tickers
Mark stickers with scales x 4 Mark stickers x 4
(10 mm wide with 1 mm scales)
• Peel from backing and attach.
Notes: 1. Rear surface is adhesive
2. Ensure surface is clean before attaching sticker
3. Do not paste over slider precaution/name plate
[1] To mark the home position
Attach to slider
Attach to base
• Attach both stickers when actuator is stopped in home position
[2] To show different movement positions
× 1 sheet
Motor
Attach to slider
Motor
Attach to movement positions
70
Catalog No.: ME3669-1A
Head Office: 2690 W. 237th Street, Torrance, CA 90505
TEL (310) 891-6015 FAX (310) 891-0815
Chicago Office: 1261 Hamilton Parkway, Itasca, IL 60143
TEL (630) 467-9900 FAX (630) 467-9912
Atlanta Office: 1220-E Kennestone Circle, Marrietta, GA 30066
TEL (678) 354-9470 FAX (678) 354-9471 website: www.intelligentactuator.com
Ober der Röth 4, D-65824 Schwalbach am Taunus, Germany
TEL 06196-88950 FAX 06196-889524
The information contained in this document is subject to change without notice for purposes of product improvement.
Copyright
© April 2009 IAI Corporation. All rights reserved.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project