Eternal Lighting | Mini60 Spot | Operating instructions | Eternal Lighting Mini60 Spot Operating instructions

Eternal Lighting Mini60 Spot Operating instructions
Mini60 Spot - 60 Watt LED Moving Head
With 3 Facet Prism
support@EternalLighting.com
832-623-9377
Table of contents
1. Before you begin
2
1.1 Packing list
2
1.2 Unpacking instructions
2
1.3 AC Power
2
1.4 Safety instructions
2
2. Introduction
2.1 Description of the fixture
3
3
2.2 Features
3
2.3 DMX channel
4
3. Setup
4
3.1 Fuse replacement
4
3.2 Fixture linking
4
Data cabling
5
DMX data cable
5
3.3 3-Pin to 5-Pin conversion chart
5
3.4 Setting up a DMX serial data link
5
3.5 Master/Slave fixture linking
6
3.6 orientation
6
4. Operating instructions
6
4.1 Navigating the control panel
6
4.2 Menu map
6
4.3 User configurations
7
Setup singl-desk light's autotocephaly moving mode(self-motion move) 7
Setup singl-desk light's autotocephaly moving mode(sound control)
7
Master/slave mode(master sound,master auto)
7
To set the pan to invertion or non-inverting
7
To set the tilt to invertion or non-inverting
7
To set the LED readout to inverting or non-inverting
7
resume reverter windows default
7
DMX mode
7
4.4 DMX channel values
8
5. Technical specifications
9
Note: The manufacture reserves the product upgrades, updates power.
1. Before you begin
1.1 Packing list
Product name
Mini moving head light
Signal cable
Power -line
quantity
1 pcs
1 base
1 base
1.2 Unpacking instructions
Immediately upon receriving a fixture, carefully unpack the carton, check the
contents to enrure that all parts are present, and have been received in good
condition. Notify the shipper immediately and retain packing material for
inspection if any parts appear damaged from shipping or the carton itself shous
sings of mishandling. Save the carton and all packing materials. In the event
that a fixture must be returned to the factory , it is important that the fixture be
returned in the original factory box and packing.
1.3 AC Power
To determin the power requirements for a particular fixture, see the label affixed
to the back plate of the fixture or refer to the fixtures specifications chart. A
fixtures listed current rating is its average current draw under normal conditions.
All fixtures must be powered directly off a switched circuit and cannot be run off
a rheostat(variable resisto) or dimmer circuit, even if the rheostat or dimmer
source voltage matches the fixtures requirement. Check the fixture or device
carefully to make sure that if a voltage selection switch exsits that it is set to the
correct line voltage you will use.
Warning! Verify that the voltage select switch on your unit matches the line
voltage applied. Damage to your fixture may rosult if the line voltage applied
does not match the voltage indicated on the voltage selector switch. All fixtures
must be connected to circuits with a suitable Earth around.
1.4 Safety instructions
Pleese read these instructions cy, it includes important information about the
installation, usage and mantenance of this product.
Please keep this user guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
Always make sure that you are connecting to the proper voltage, and that the
line voltage you are connectiong to is not higher than that stated on the decal or
rear panel of the fixture.
This product is intended for indoor use only!
To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make
sure there are no flammable materials close to the unit while opearating.
The unit must be installed in a location with adequate ventilation, at least
2
Note: The manufacture reserves the product upgrades, updates power.
20in(50cm) from adjacent surfaces. Be sure that no ventilation slots are blocked.
Always disconnect from poer source before servicing or replacing fuse and be
sure to repalce with same fuse size and type.
Secure fixture to fastening device using a safety chain. Never carry the fixture
solely by its heda. Use its carrying handles.
Maximum ambient temperature (Ta) is 104T (40°C ). Do not operate fixture at
temperatures higher than this.
In the event of a serious operating problem, stop using the unit immediately.
Never try to repair the unit by yourself. Repairs carried out by unskiiled people
can lead to damage or malfunction. Plesse contact the nearest authorized
technical assistance center. Always use the same type spare parts.
Don't connect the device to a dimmer pack.
Make sure the power cord is never crimped or damaged.
Never disconnect the power cord by pulling or gugging on the cord.
Avoid direct eye exposure to the light source while it is on.
2. Introduction
2.1 Description of the fixture
1.Moving head
10.Fuse holder
2.Yoke
11.3 pin DMX
3.Fan
4.Base
5.Base panel
output & input
12.Function Button
13.Hook
6.Display panel
7.Handle
8.Power switch
10
9.Power cord
2.2 Features
Specification
LEDs
30w RGB 30w White 60w White
LED
LED
LED(C)
White LED(C)
RGB LED White LED
DMX channal
13
Color wheel
No
60w White
60w White
60w White
LED(C )
LED(F) with
LED(F)
prism
with prism
11
White LED(F)
12
11
7 colors+open,raindow effect.
Gobo wheel
6 gobos +open,gobo wheel spin effect.
Dimmer
0-100%
-100%
Focus
Prism
Yes
12
No
No
No
Yes
3
Note: The manufacture reserves the product upgrades, updates power.
No
Yes
Strobe
Variable electronic strobe.
Control
Auto-running,Master/slave mode,DMX.
LED display
LED display menu with invert.
Pan/Tilt
Pan 630°,Tilt 240°,Pan /Tilt speed from fast to slow.
Reset
Yes
Fan cool
Yes
2.3 DMX channel
Function
1 Channel
30w White LED
30w RGB LED
60w White LED with prism!
1
2
Pan
Tilt
Pan
Tilt
Pan
Tilt
3
4
Color wheel
Gobo wheel
Gobo rotating
Strobe
Dimmer
Pan /tilt speed
Pan fine
Focus
Gobo wheel
Gobo rotationg
Strobe
Color wheel
Gobo wheel
Gobo rotating
Strobe
Dimmer
Prism
Pan /tilt speed
Tilt fine
Red
Green
Blue
Pan /tilt speed
Reset
Pan fine
Tilt fine
12
Tilt fine
Reset
13
Reset
5
6
7
8
9
10
11
Pan fine
3. Setup
Disconnect the power cord before replacing a fuse and always replace with the
same type fuse.
3.1 Fuse replacement
With a flat head screwdriver wedge the fuse holde out of its housing. Remove
the damaged fuse from its holder and replace with exact same type fuse. Insert
the fuse holder back in its place and reconnect power.
3.2 Fixture linking
You will need a serial data link to run light shouw of one or more fixtures using a
DMX-512 controller or to run synchronized on two or more fixtures set to a
master/slave operating mode. The combined number of channels required by all
the fixtures on a serial data link determines the number of fixtures the data link
can support.
Maximum recommended serial data link distance:500 meters(1640ft).
Maxinnim recommended number of fixtures on a serial dqta link:32 fixtures.
4
Note: The manufacture reserves the product upgrades, updates power.
Data cabling
To link fixtures together you must obtain data cables. If you choose to craete
your own cable pleae use data-grade cables that can carry a high quality signal
and are less prone to electromagnetic interference.
DMX data cable
Use a belden 9841 or equivalent cable which meets the specifications for EIA
RS-485 applications. Standard microphone cables cannot transmit DMX datat
reliably over long distances. The cable will have the following characterstics:
2-conductor twisted pair plus a shield.
maximum capacitance between conductors-30 pF/ft.
maximum capacitance between conductor and shield -55 pF/ft.
mavimum resistance of 20 ohms/1000ft.
nominal impedance 100-140 ohms.
3.3 3-Pin to 5-Pin conversion chart
Note! If you use a controller with a 5 pin DMX output connetor. you will need to
use a 5pin to 3 pinasapter
CHAUVET Model No:DMX5M. orDMX 5F
The chart below details a proper cable conversion:
Occupation of the XLR-connection:
DMX - output
DMX-input
XLR mounting-plugs (rear view):
XLR mounting-sockets (rear view):
1 - Shield
2 - Signal (-)
3 - Signal (+)
4 - Not connected
5 - Not connected
3.4 Setting up a DMX serial data link
at first link the first light and DMX control through XLR-conncetion signal
cable,then devoluted the light in series ,as the follow
DMX 512
DMX 512
1200
DMX Controller
5
Note: The manufacture reserves the product upgrades, updates power.
This mode allows the until to be controlled by any universal DMX controller.
The default mode for the fixture is DMX, as follow.
4.4 DMX channel values
Channel
30w
White
LED
30w
RGB
LED
60w White
LED with
prism
1
1
1
2
2
2
Function
Value
Pan
0 - 255
pan circumrotate 630°
Tilt
0 - 255
Tilt circumrotate 240°
Color wheel
3
-
3
0-7
8-15
16-23
24-31
32-39
40-47
48-55
56-63
64-71
72-79
80-87
88-95
96-103
104-111
112-119
120-127
128-192
193-255
Open/White
White+Color1
Color 1
Color 1 +Color 2
Color 2
Color 2+Color 3
Color 3
Color 3+Color 4
Color 4
Color 4 +Color 5
Color 5
Color 5+Color 6
Color 6
Color 6+Color7
Color 7
Color 7+White
Color wheel positive turn , Speed from fast to slow
Color wheel reversal speed increase fast
Gobo wheel
4
4
4
5
5
5
7
_
6
6
0-17
18-36
37-55
56-74
75-93
94-112
113-127
128-192
193-255
Open/White
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo wheel positive turn, Speed from fast to slow
Gobo wheel reversal speed increase fast
Gobo auto running
-
7
0
1-127
128-255
No
Gobo wheel positive turn, Speed from fast to slow
Gobo wheel reversal speed increase fast
Dimmer
0 - 255
0 - 100%
Strobe
6
0
1 - 255
No
Slow--fast
Pan /tilt speed
8
10
9
9
11
10
0
1-255
Most speed
Speed from fast to slow
Pan fine
8
Note: The manufacture reserves the product upgrades, updates power.
1-225
Speed from fast to slow
9
11
10
0-225
Pan fine 16bit
10
12
11
0-255
Tilt fine 16bit
11
13
12
0-149
150-200
No
reset(delay 3 second)
-
-
8
0-12
13-225
No
Prism
-
3
-
0
1-255
No
Focus
0-255
0-100%
0-255
0-100%
0 - 255
0 - 100%
Pan fine
Tilt fine
Reset
Prism
Focus
_
7
8
_
9
Red
_
Green
-
_
Blue
5. techno specifation iuminllate
-
Specification
30w RGB 30w White 60w White 60w White 60w White 60w White
LED(F
LD
E (C)
LED(F )
LED
LED(C )
LED
with prism
wit h
prism
Power supply
110 -245V 50/60Hz
Power consumption
72W
LED(s)
14.5V 2.1A
Fuse
102W
17.5V
110W
5/2A, 05x20mm
Pan
630°,16bit fine
Tilt
240°,16bit fine
Tiptop environment
temperature
104°F(40°C)
Date input/output
3pin XLR-conntion, anlde socket
Outside size
280x280x370mm (LxWxH)
110W
102W
3.35A
13.8A
9
We'. The manufacture reserves the product upgrades, updates power.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising