VDC-275-10
VDC-275 / VDC-276 - Quick Install
1
1/2
2
3
4
Menu (set)
INT
LL
Guide Pattern
Sync.
Guide pattern
Dome base
Focus
not included
BNC
female
4x screws
Zoom
24 VAC /
12 VDC
Class 2
Dome cover
Twist
Tilt
1 Vpp
75 Ohm
Pan
1
1.1
Safety
1.2
Important safety instructions
1.3
FCC & ICES compliance
1.4
Bosch notices
1.
Read these instructions.
FCC & ICES Information
Disposal - Your Bosch product was developed and
Safety precautions
2.
Keep these instructions.
This equipment has been tested and found to comply with the
manufactured with high-quality material and components that
3.
Heed all warnings.
DANGER!
limits for a Class A digital device, pursuant to part 15 of the
can be recycled and reused. This symbol means that
4.
Follow all instructions
High risk: This symbol indicates an imminently hazardous
FCC Rules. These limits are designed to provide reasonable
electronic and electrical appliances, which have reached the
5.
Do not use this apparatus near water.
protection against harmful interference in a residential
situation such as "Dangerous Voltage" inside the product.
end of their working life, must be collected and disposed of
6.
Clean only with a dry cloth.
environment. This equipment generates, uses, and can radiate
If not avoided, this will result in an electrical shock, serious
separately from household waste material. Separate collecting
7.
Install in accordance with the manufacturer's instructions.
radio frequency energy and, if not installed and used in
bodily injury, or death.
systems are usually in place for disused electronic and
8.
Do not install unit near any heat sources such as radiators,
accordance with the instructions, may cause harmful
electrical products. Please dispose of these units at an
heat registers, stoves, or other apparatus (including
interference to radio communications. However, there is no
amplifiers) that produce heat.
environmentally compatible recycling facility, per European
guarantee that interference will not occur in a particular
Protect the power cord from being walked on or pinched
Directive 2002/96/EC
installation. If this equipment does cause harmful interference
If not avoided, this could result in minor or moderate bodily
particularly at plugs, convenience receptacles, and the
to radio or television reception, which can be determined by
Optical elements
injury.
point where they exit from the apparatus.
turning the equipment off and on, the user is encouraged to try
Optical elements are sensitive and should be protected at all
to correct the interference by one or more of the following
times. Do not allow objects to come into contact with glass
measures:
surfaces and do not touch optical elements with your fingers.
WARNING!
Medium risk: Indicates a potentially hazardous situation.
9.
10. Only use attachments/accessories specified by the
CAUTION!
Low risk: Indicates a potentially hazardous situation.
If not avoided, this could result in property damage or risk of
damage to the unit.
manufacturer.
11. Unplug this apparatus during lightning storms or when
unused for long periods of time.
The Low Voltage power supply unit must comply with EN60950
/ UL60065. The power supply must be a SELV-LPS unit or a
SELV - Class 2 unit (Safety Extra Low Voltage - Limited Power
Source).
reorient or relocate the receiving antenna;
–
increase the separation between the equipment and
12. Refer all servicing to service personnel. Servicing is
required when the apparatus has been damaged in any
CAUTION!
–
receiver;
–
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
connect the equipment into an outlet on a circuit different
from that to which the receiver is connected;
–
Installation should only be performed by qualified service
personnel in accordance with the National Electrical Code or
applicable local codes.
This manual is the intellectual property of Bosch Security
Systems and is protected by copyright.
All rights reserved.
consult the dealer or an experienced radio/TV technician
Trademarks
for help.
All hardware and software product names used in this
not operate normally, or has been dropped.
document are likely to be registered trademarks and must be
Intentional or unintentional modifications, not expressly
approved by the party responsible for compliance, shall not be
CAUTION!
Copyright
made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult
the dealer or an experienced radio/television technician for
corrective action.
treated accordingly.
Note
Bosch Security Systems accepts no liability for damage
resulting directly or indirectly from faults, incompleteness or
discrepancies between the user guide and the product
described.
More information
For more information please contact the nearest Bosch Security
Systems location or visit www.boschsecurity.com
AM18-Q0639
Analog Camera Menus
1
Setup menu | en
1
Setup menu
Analog Camera Menus
1.1
Setup menu | en
2
Main menu
Analog Camera Menus
1.1.2
Setup menu | en
Shutter/AGC (Automatic Gain Control) menu
SHUTTER/AGC AUTO
Press straight down on the button of the control pad to access the SETUP
LENS
menu.
SHUTTER/AGC
WHITE BAL
Menu
Move the button up or down to move the cursor through the menus.
–
Move the button to the right or left to change values.
–
When the symbol
select an item or open a submenu.
SPEED
0 - 255
MODE
SHUT
DELAY CNT
0 - 255
BRIGHTNESS
0 - 255
ATW FRAME
x0.50, x1.00, x1.50, x2.00
ENVIRONMENT
INDOOR, OUTDOOR
HIGH LUMINANCE
MODE
AGC, OFF
PUSH
BRIGHTNESS
x0.25, x0.50, x0.75, x1.00
USER1
PRIVACY
RETURN
MANUAL MODE
To move to the continuation of a menu, select NEXT.
–
To return to the previous menu, select BACK or RETURN.
–
To save changes, select SAVE ALL.
–
To close the SETUP menu, select EXIT.
B-GAIN
0 - 255
R-GAIN
0 - 255
SYNC
10000 (NTSC)
RETURN
LANGUAGE
1/50, 1/100, 1/250, 1/500,
Camera reset sets all parameters to their factory default values.
1.1.1
–
1.1.4
Backlight menu
5
AGC
1/1000, 1/2000, 1/4000, 1/
ANTI CR
10000 (PAL)
MANUAL LEVEL
6.00, 12.00, 18.00, 24.00,
PUSH
RETURN
TYPE
LOCK
DC
MODE
AUTO
SPEED
0 - 255
Setup menu | en
Motion detection menu
BLC
DETECT SENSE
0 - 127
HLC
BLOCK DISP
OFF, ON, ENABLE
Use BLC (Back Light Compensation) to see a dark object in front of a
MONIOTR AREA
OFF, ON
bright background.
AREA SEL
1-4
–
Use HLC (High Light Compensation) to darken highlights and avoid
TOP
0 - 244 (NTSC), 288 (PAL)
image wash-out (for example, car headlights).
BOTTOM
0 - 244 (NTSC), 288 (PAL)
LEFT
0 - 474 (NTSC), 468 (PAL)
RIGHT
0 - 474 (NTSC), 468 (PAL)
Picture adjust menu
PICT ADJUST
MIRROR
ON, OFF
BRIGHTNESS
0 - 255
CONTRAST
0 - 255
6
Analog Camera Menus
Setup menu | en
SHARPNESS
0 - 255
HUE
0 - 255
GAIN
0- 255
RETURN
1.1.6
ATR
Adaptive Tone Reproduction menu
OFF
LUMINANCE
LOW, MID, HIGH
CONTRAST
LOW, MID, HIGH
RETURN
–
Use ATR (Adaptive Tone Reproduction) to improve dynamic range by
highlight compression and contrast enhancement.
PRIVACY
Top: extend or reduce upper limit of the detection area.
–
Bottom: extend or reduce bottom limit of the detection area.
–
Left: extend or reduce left limit of the detection area.
–
Right: extend or reduce right limit of the detection area.
TOP
LEFT
1
7
Use PUSH LOCK with a reference white object filling the screen.
Analog Camera Menus
CAMERA ID
reduce
RIGHT
OFF
DAY/NIGHT
1
When ON is selected, a virtual keyboard appears on the screen. Use the
enter the camera ID you desire. You can enter up to 52 characters.
1.1.12
BURST
OFF, ON
1-4
DELAY CNT
0 - 255
TOP
0 - 244 (NTSC), 288 (PAL)
DAY->NIGHT
0 - 255
BOTTOM
0 - 244 (NTSC), 288 (PAL)
NIGHT->DAY
0 - 255
LEFT
0 - 474 (NTSC), 468 (PAL)
RETURN
RIGHT
0 - 474 (NTSC), 468 (PAL)
COLOR
1-8
TRANSP
0.00, 0.50, 0.75, 1.00
MOSAIC
OFF, ON
OFF, ON
RETURN
1.1.10
NR
Noise reduction menu
NR MODE
OFF, Y, C, Y/C
Y LEVEL
0 - 15
C LEVEL
0 - 15
RETURN
L/L
PHASE
0 - 524 (624)
–
Sync. is always internal for 12 VDC cameras.
1.1.13
LANGUAGE
Language menu
ENGLISH, JAPANESE, GERMAN, FRENCH, RUSSIAN,
PORTUGUESE, SPANISH, SIMPLIFIED CHINESE
COLOR
BURST
Synchronization menu
RETURN
AREA SEL
B/W
OFF
RETURN
extend
Day/night menu
AUTO
Camera identification menu
ON
SYNC.
1.1.9
Setup menu | en
control pad to move to the character you want and select it. Repeat this to
RIGHT
BOTTOM
Privacy masking menu
RETURN
Use ANTI CR (Anti Color Rolling) when certain types of fluorescent light
1.1.11
–
RETURN
1.1.8
–
–
Area selection for motion or privacy masks
OFF
–
1.1.5
ATW (Auto Tracking White balance: 2,500 K to 8,500 K) and PUSH (Full
cause the picture to periodically change color.
Analog Camera Menus
MOTION DET
–
pull-in: 1,800 K to 10,500 K) continuously analyze color temperature.
For cameras with a fixed lens only manual mode is used.
1.1.7
OFF
0 - 90 (NTSC), 97 (PAL)
RETURN
30.00, 36.00, 42.00, 44.80
Lens menu
AUTO
USER2
1/60, 1/120, 1/250, 1/500,
Select area 1, 2, 3 or 4.
BACKLIGHT
0 - 255
RETURN
SHUT+AGC
RETURN
Setup menu | en
0 - 255
R-GAIN
1/1000, /2000, 1/4000, 1/
LENS
Analog Camera Menus
B-GAIN
CAMERA ID
SHUTTER
4
RETURN
MOTION DET
–
–
ATW
ATR
CAMERA RESET
Navigation items at the bottom of the screen
WHITE BAL
Setup menu | en
White balance menu
LOW LUMINANCE
NR
is shown, press straight down on the button to
1.1.3
PICT ADJUST
DAY/NIGHT
–
Analog Camera Menus
RETURN
BACKLIGHT
Set
3
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement