Dual | XDMA6415 | User`s manual | Dual XDMA6415 User`s manual

Dual XDMA6415 User`s manual
XDMA6415
INSTALLATION/OWNER'S MANUAL
AM/FM/CD/MP3/WMA Receiver with Detachable Face
XDMA6415 INSTALLATION
Preparation
Please read entire manual before installation.
Before You Start
•Disconnect negative battery terminal. Consult a qualified technician for instructions.
•Avoid installing the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
• Remove trim ring from unit,
• Remove 2 transit screws located
on top of the unit.
• Insert the supplied keys into the
slots as shown, and slide the unit
out of the mounting sleeve.
• Install mounting sleeve into
opening, bending tabs to secure.
• Connect wiring harness and
antenna. Consult a qualified
technician if you are unsure.
• Certain vehicles may require an
installation kit and/or wiring
harness adapter (sold separately).
• Test for correct operation and slide
into mounting sleeve to secure.
• Snap trim ring into place.
KEYS
MOUNTING STRAP
HEX NUT
HEX BOLT
PLAIN WASHER
MOUNTING SLEEVE
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
2
XDMA6415 INSTALLATION
Wiring Diagram
RCA Connections
Right Channel (Red)
Left Channel (White)
REAR
SUBWOOFER
FRONT
FRONT
SUB/W
L-CH
R-CH
REMOTE IN
Antenna
Connector
Steering Wheel Interface Input
(PAC SWI-PS required)
BLACK Bluetooth Microphone Input
Connect the included
Bluetooth microphone.
Bluetooth Microphone
(must be connected for Bluetooth functionality)
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The XDMA6415 uses one
10 amp ATM fuse located
beside the wiring connector.
3
XDMA6415 OPERATION
Control Locations - Receiver
1
2
21
20
19
18
17
3
4
5
16
15
14
6
7
13
8
9
10 11
12
1
Release
12
Auxiliary Input
2
Talk
13
Tune/Track Up
3
Audio/Menu
14
Tune/Track Down
4
Preset 1/Repeat
15
Display
5
Preset 4/Play/Pause
16
Volume
6
Preset 2/Random
17
AS/PS/Enter
7
Preset 5/Folder Down
18
Band/Back
8
Preset 3/Intro
19
Mode/Search
9
Preset 6/Folder Up
20
Power
10
Eject
21
Mute/End Call
11
USB Port
The XDMA6415 allows playback of your favorite MP3 and WMA files recorded on CD-R and
CD-RW discs. Its powerful on-board DSP processor decodes the compressed audio while
maintaining near-CD sound quality. An internal SRAM buffer provides ESP (Electronic
Skip Protection) to virtually eliminate skipping and allows alphanumeric or direct track
search - even while a song is currently playing!
4
XDMA6415 OPERATION
Control Locations - Remote
1
2
4
3
5
21
6
20
7
19
8
9
18
10
17
11
12
16
13
15
14
1
Power
11
Preset 5/Folder Down
2
Audio/Menu
12
Key 9/EQ
3
Volume Up
13
Mute/End Call
4
Mode/Search
14
Key 0/Display
5
Tune/Track Up
15
Talk
6
Volume Down
16
Key 8/Scan
7
AS/PS/Enter/# Key
17
Key 7
8
Preset 3/Intro
18
Preset 4/Play/Pause
9
Preset 2/Random
19
Preset 1/Repeat
10
Preset 6/Folder Up
20 Band/Back/* Key
21 Tune/Track Down
5
XDMA6415 OPERATION
General Operation
Faceplate Removal
Semi-Permanent
Faceplate Installation
Press RELEASE and pull away from the left side to remove.
To re-install, insert right side of faceplate first then push
left side to secure.
Remove trim ring and install supplied #1 x 7/32” Phillips
head screw through left side of mounting frame into faceplate.
Power On/Off
Press POWER or any other button (except eject) to turn the
unit on. Inserting a disc will turn the unit on automatically.
Press POWER to turn the unit off.
Mode
Press MODE to select between AM/FM, CD player, auxiliary
input, operation of iPod®, Bluetooth and USB. Modes of
operation are indicated in the display. CD mode will not
appear unless a CD is inserted.
Auxiliary Input
Insert a 3.5mm connector in the front panel AUX port.
Connect the other end of the 3.5mm connector to the
headphone output of an audio device, MP3 player, etc. Press
MODE to select AUX mode.
Steering Wheel
Input Interface
The steering wheel interface input located on the back of
the head unit allows connection to the Pacific Accessory
Corporation (PAC) SWI-PS interface module (sold separately).
Visit www.pac-audio.com for details.
To configure steering wheel controls, follow the instructions
provided with the PAC SWI-PS interface module. After
installing the interface module, insert the module's 3.5mm
jack into the port on the back of the head unit.
Volume
Programmable Turn-On Volume
Mute
Preset EQ Curves
Display
6
Adjust volume using the volume knob (00-46).
Press and hold POWER for 3 seconds to program currently
selected volume level. "P-VOL" and the current volume level
will momentarily appear in the display.
Press to silence the audio. “MUTE” will flash in the
display. Press again to cancel.
On the remote control, press EQ to select between POP,
JAZZ, CLASSIC, BEAT, ROCK and OFF (default) equalization
curves. Any adjustment to the Bass or Treble settings
automatically cancels the current EQ curve (if one is
selected).
Press DISP to select between clock and different types of
information, such as radio frequency, CD track/elapsed time,
or MP3/WMA song information.
XDMA6415 OPERATION
General Operation
Reset
Press to RESET the unit upon initial installation or if abnormal
operation occurs. Reset button is located behind the faceplate.
Set the Clock
With the unit on, press and hold DISP until the clock begins to
flash, then release. Press TUNE
to adjust the hours and
TUNE
to adjust the minutes. Press DISP momentarily to
save the selected time.
nn
ll
12/24-hour Clock
Setup Menu
The clock will display 12-hour AM/PM time in USA frequency
spacing mode (PM 10:00). In European frequency spacing
mode, the clock will display 24-hour time (22:00).
Press and hold AUDIO/MENU for more than 3 seconds to
access the setup menu. Press AUDIO/MENU momentarily to
select between the menu functions and rotate the volume knob
left/right to adjust or activate the desired function.
Setup Menu
Menu Function
Loudness Curve
Tuner Frequency
Spacing
Options
Disables the loudness function.
LOUD ON
CLK OFF
CLK ON
AUX ON
Enables the loudness function. Activating this feature will
enhance the bass and treble frequencies when listening to
music at low volumes.
Programs the unit to USA tuner spacing.
(200kHz for FM and 10kHz for AM)
Programs the unit to European tuner spacing.
(50kHz for FM and 9kHz for AM)
Programs the unit to not display the clock when the power is off.
Programs the unit to display the clock when the power is off.
Enables the front panel 3.5mm auxiliary input.
FREQ USA
FREQ EUR
Clock Display
Auxiliary Input
Action
LOUD OFF
AUX OFF
Disables the auxiliary input.
Beep Confirmation
BEEP OFF
BEEP ON
Disables the confirmation beep.
Enables the confirmation beep.
Local/Distance
Tuning
LOC OFF
Activates distance tuning.
LOC ON
Activates local tuning for strong station reception only.
Subwoofer
SB-W ON
Enables the subwoofer RCA output
SB-W OFF
Disables the subwoofer RCA output
MSG OFF
Disables power on message.
MSG ON
Enables power on message to be displayed.
DEMO OFF
Disables the demonstration message.
DEMO ON
Enables the demonstration message.
Power on Message
Demonstration
Mode
Note: Refer to page 24 for Bluetooth setup menu options.
7
XDMA6415 OPERATION
General Operation
Audio
Press AUDIO/MENU momentarily to select between Volume
(default), Bass, Treble, Balance, & Fader.
VOLUME
BASS
TREBLE
BALANCE
FADER
SUBWOOFER
Bass
Press AUDIO/MENU until BAS appears then rotate volume
left/right to adjust ( -6 minimum / +6 maximum).
Treble
Press AUDIO/MENU until TRE appears then rotate volume
left/right to adjust ( -6 minimum / +6 maximum).
Balance
Press AUDIO/MENU until BAL appears then rotate volume
left/right to adjust (BAL L 12-BAL 00-BAL R 12).
BAL 00 represents equal balance
Fader
Press AUDIO/MENU until FAD appears then rotate volume
left/right to adjust (FAD F 12-FAD 00-FAD R 12).
FAD 00 represents equal fader
Subwoofer
Press AUDIO/MENU until SUB appears, then press SELECT
to confirm. Rotate volume left/right to adjust (0-12). Adjusting levels to 0 turns the subwoofer off.
Source Audio Memory
Individual Bass and Treble settings are retained in memory
for tuner, CD, AUX, USB and operation of iPod modes. This
allows you to save the Bass and Treble settings separately
for each mode.
Note:
Any adjustment to the Bass or Treble settings automatically
cancels the current EQ curve (if one is selected).
8
XDMA6415 OPERATION
Seek Tuning
Manual Tuning
AM/FM Tuner Operation
Press TUNE nn or TUNE ll momentarily to seek the
next strong station.
nn
ll
Press TUNE
or TUNE
for more than two seconds,
then release. "MANUAL" will momentarily appear in the
display. Press TUNE
or TUNE
momentarily to
move radio frequency up or down one step at a time. Press
and hold to advance quickly. If tuning is not adjusted for five
seconds, the unit will return to seek tuning mode (default).
"AUTO" will momentarily appear in the display.
nn
ll
Scan Tuning
On the remote control, press SCAN to preview strong
stations on the current band, pausing for five seconds at
each. Press SCAN again to cancel.
Band
Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands.
Storing and Recalling
Station Presets
Up to 18 FM stations and 12 AM stations can be stored. To
store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
two seconds. When stored, the preset number will appear in
the display. The station can be recalled anytime by pressing
the corresponding preset button.
Note: Function keys 7, 8, 9 and 0 on the remote control apply
to Bluetooth operation only.
Automatically Store
Stations
Preset Scan
Press AS/PS for more than two seconds to automatically
store the six strongest stations in the current band.
Automatic local tuning is activated during the initial band
scan.
Press AS/PS for less than two seconds to scan presets 1-6
on the current band, pausing for five seconds at each. Press
AS/PS again to cancel.
9
XDMA6415 OPERATION
CD Player Operation
Insert CD
Eject CD
Track Select
Fast Forward and Reverse
Pause
Scan
Repeat
Random
CD-R/CD-RW Compatibility
With the label facing up, insert a standard size CD into the
CD slot. The CD will automatically begin playback.
Press to eject the CD. The unit will change to previous
mode of operation (AM/FM, AUX, operation of iPod,
Bluetooth or USB). If the disc is not removed within 10
seconds, the unit will reload the disc. The unit does not have
to be turned on to eject CD.
ll
Press TRACK
to skip to the beginning of the next
track. Press TRACK
to return to the beginning of the
current track. Pressing TRACK
again skips to the
beginning of the previous track.
nn
Press and hold TRACK
or reverse a track.
Press
Press
nn
ll or TRACK nn to fast forward
temporarily stop CD playback.
ll// IIII toagain
to resume playback.
Press INT to play the first 10 seconds of each track.
Press INT again to cancel.
Press RPT to continuously repeat selected track.
Press RPT again to cancel.
Press RDM to play all tracks in random order. Press RDM
again to cancel. Random mode is retained in memory when
selecting between AM/FM, CD, AUX, USB, operation of iPod
and Bluetooth modes and when the unit is turned on/off. Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method. In
addition, the following CDs may be incompatible with this
unit:
CDs exposed to extreme temperatures or direct sunlight
for extended periods of time, CDs recorded in which a
recording session failed or a re-recording was attempted
and, or encrypted or copy-protected CDs which do not
conform to the audio CD-DA red book recording standard.
10
XDMA6415 OPERATION
CD Player Operation - MP3/WMA Files
Playing an MP3/WMA Disc
When an MP3/WMA encoded disc is first inserted,
“READING” will appear in the display. Depending on the
number of files and folders, this may take several seconds.
Displaying Information
Press DISP to select between track number/elapsed time
(default), clock, track name, directory name, title, artist and
album.
“NO ID3 TAG” will be displayed if the MP3 file contains no
ID3 tag information.
“UNKNOWN” will be displayed if the WMA file contains no WMA tag information.
“ROOT” will be displayed if the directory name of a root
folder is not labeled.
Title Icon
This icon will illuminate when the artist name is displayed.
Artist Icon
Album Icon
This icon will illuminate when the song title is displayed.
Folder Icon
Character Support
This icon will illuminate when the album name is displayed.
This icon will illuminate when the folder name is displayed.
Maximum character display information
• Track name – 32 character maximum
• Directory name – 23 character maximum
• *Song title – 30 character maximum
• *Artist name – 30 character maximum
• *Album name – 30 character maximum
*Song title, Artist Name, and Album name, will only be
displayed if included with the MP3/WMA file.
When referring to MP3/WMA playback, the following terms
are synonymous:
• File name and track name
• Folder name and directory name
11
XDMA6415 OPERATION
CD Player Operation - MP3/WMA Files
Direct Select and
Navigate Modes
Press SRCH for more than 3 seconds, to select between the
following modes:
• Direct File Select
• File or Folder Navigate
Direct File Select
Step 1
Press SRCH for more than 3 seconds, then release.
“MP3 T " or “WMA T ” will flash in the display.
*
*
Step 2
Turn the volume knob to change to the desired track
number.
Step 3
Press
to confirm the selected file number or wait for
the input cycle to time out (approximately 5 seconds).
File/Folder Navigate
Step 1
Press SRCH for more than 3 seconds, then release.
Press SRCH again to navigate files/folders on the disc.
The current folder name will scroll one time followed by
available files and folders.
Step 2
Turn the volume knob to preview files/folders in the current
folder. If a folder is selected, the icon will illuminate.
Step 3
Press
to select the desired file or folder. If a folder is
selected, "\ \ " will be displayed. Turn the volume knob to the
right to begin searching files in the folder.
Step 4
Press
*Folder Access
(Up one level)
to select the desired file within the folder.
When navigating folders (and “\ \“ is displayed), press BACK
to access the previous level (up one level).
*Only available on MP3/WMA discs recorded with more than
one folder.
12
XDMA6415 OPERATION
CD Player Operation - MP3/WMA Files
Navigating Note
*Folder Access
After navigating by direct select or file/folder navigate
modes, the track number and elapsed time will be displayed
by default. Press DISP momentarily to select clock, track
name, directory name, title, artist and album.
Press to select the previous folder.
Press to select the next folder.
*Folder access is only available on MP3/WMA discs recorded
with more than one folder.
File Repeat
Press RPT momentarily to continuously repeat selected file.
Press RPT again to cancel.
Folder Repeat
Press RPT for more than 2 seconds to consecutively repeat
all files in the current folder only. The icon will appear in
the display when in folder repeat mode.
Press RPT again to cancel.
Disc Random
Press RDM momentarily to play all files on entire disc in
random order. Press RDM again to cancel.
Folder Random
Disc Intro
Folder Intro
Press RDM for more than 2 seconds to play all files in
current folder only in random order. The icon will appear
in the display when in folder random mode.
Press RDM again to cancel.
Press INT momentarily to play the first 10 seconds of each
file on the entire MP3/WMA disc. Press INT again to cancel.
Press INT for more than 2 seconds to play the first 10
seconds of each file in the current folder only. The icon
will appear in the display when in folder intro mode.
Press INT again to cancel.
Note:
Folder repeat, folder random and folder intro functions are
only available on MP3/WMA discs recorded with more than
one folder.
13
XDMA6415 OPERATION
CD Player Operation - MP3/WMA Files
Media Compatibility
The following types of discs/files are compatible:
• CD-ROM (ISO), CD-R, CD-RW
• CD-DA
• MP3 data
• WMA data
The following types of discs/files are not compatible:
• WMA files that are protected by DRM (Digital Rights Management).
• WMA lossless format
• Discs recorded with Track At Once or packet writing
• MP3 PRO format
• MP3 playlists
• WAV format
Playback Order
Compatible Recording
Formats
MP3/WMA playback sequence is based on recorded order
of files and begins in the root folder of the disc. Any empty
folders or folders that do not include MP3/WMA files are
skipped. This unit may not play files in the order they were
recorded in depending on the recording software used.
Refer to your recording software’s user’s manual for more
information.
• ISO9660 level 1
• ISO9660 level 2
• Yellow Book MODE 1
• Yellow Book MODE 2 FORM 1
• Multi session
• Maximum folders and files - 256
• Maximum folder levels - 8
• MPEG-1/2/2.5 Audio Layer-3
ISO9660 standards:
• Maximum nested folder depth is 8 (including the root
folder).
• Valid characters for folder/file names are letters A-Z
(all caps), numbers 0-9, and “_” (underscore). Some
characters may not be displayed correctly, depending on
the character type.
• This device can play back discs in Joliet, Romeo, and other standards that conform to ISO9660. MP3/WMA written in the formats other than the above may not play and/or their file names or folder names may not be displayed properly.
14
XDMA6415 OPERATION
CD Player Operation - MP3/WMA Files
Additional MP3/WMA
Information
An internal buffer provides ESP (Electronic Skip Protection) to
virtually eliminate skipping.
When playing a disc recorded with regular audio files
(CD-DA or .WAV) and MP3/WMA files, the unit will play the
MP3/WMA files only.
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be played.
Do not attempt to play discs which contain non-MP3/WMA
files with the MP3/WMA extension.
Sampling Frequency Rates
MP3
WMA
Transfer Bit rates
MP3
WMA
8kHz ~ 48kHz
32kHz ~ 48kHz
32kbps ~ 320kbps constant
Variable bit rates
48kbps ~ 192kbps constant
Variable bit rates
Note:
Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3 Tag Display
Recommended Settings
ID3 tags Version 1.x
This model will not display ID3 Version 2.0 or greater tags.
For best results, use the following settings when burning an
MP3 disc:
128kbps or higher constant bit rate
44.1kHz or higher sampling frequency
For best results, use the following settings when burning a
WMA disc:
64kbps or higher constant bit rate
32kHz or higher sampling frequency
15
XDMA6415 OPERATION
USB Operation - MP3/WMA Files (Optional)
Connecting a USB Device
(sold separately)
Playing Music
Displaying Information
Play MP3/WMA files from most mass storage devices by
connecting them to the XDMA6415's USB port. To connect
a USB device, line up the connectors and insert the USB
device into the port. The USB icon will appear in the display.
Press MODE to enter USB mode. When a USB device is
first connected, “READING” will appear momentarily in
the display. Depending on the number of files and folders,
this may take several seconds. Music will begin playing
automatically unless a Bluetooth phone call is detected.
If no valid MP3/WMA files are detected, "NO FILE" will be
displayed and the last mode will be resumed.
Press DISP to select between elapsed time (default), track
number, clock, track name, directory name, title, artist and
album.
"NO TITLE" will be displayed if no song title information is
available.
"NO ARTIST" will be displayed if no artist information is
available.
"NO ALBUM" will be displayed if no album information is
available.
This icon will illuminate when the song title is displayed.
Title Icon
Artist Icon
This icon will illuminate when the artist name is displayed.
Album Icon
This icon will illuminate when the album name is displayed.
Folder Icon
Character Support
This icon will illuminate when the folder name is displayed.
Maximum character display information
• Track name – 32 character maximum
• Directory name – 32 character maximum
• *Song title – 30 character maximum
• *Artist name – 30 character maximum
• *Album name – 30 character maximum
*Song title, artist name and album name will only be
displayed if included with the MP3/WMA file.
16
XDMA6415 OPERATION
USB Operation - MP3/WMA Files (Optional)
Direct File Select
Press SEARCH for more than three seconds, then release.
"T*" will appear in the display. Use the volume knob to select
the desired track number and press to confirm.
Note: When a file is accessed, the elapsed time will be
displayed. Press DISP momentarily to select track number,
clock, track name, directory name, title, artist or album.
*Folder Access
Press to select the previous folder.
Press to select the next folder.
*Folder access is only available on USB devices with more
than one folder.
File Repeat
Press RPT momentarily to continuously repeat selected file.
Press RPT again to cancel.
Folder Repeat
Press RPT for more than two seconds to consecutively
repeat all files in the current folder only. The icon will
appear in the display. Press RPT again to cancel.
File Random
Press RDM for more than two seconds to play all files on
entire USB device in random order. Press RDM again to
cancel.
Folder Random
Press RDM momentarily to play all files in current folder
only in random order. The icon will appear in the display.
Press RDM again to cancel.
File Intro
Press INT momentarily to play the first 10 seconds of each
file on the entire USB device. Press INT again to cancel.
Folder Intro
Press INT for more than two seconds to play the first 10
seconds of each file in the current folder only. The
icon
will appear in the display. Press INT again to cancel.
Note: Folder repeat, folder random and folder intro functions
are only available on USB devices with more than one folder.
17
XDMA6415 OPERATION
USB Operation - MP3/WMA Files (Optional)
Track Select Press TRACK ll to skip to the beginning of the next
track. Press TRACK nn to return to the beginning of the
current track. Pressing TRACK nn again skips to the
beginning of the previous track.
Fast Forward and Reverse
Pause
Media Compatibility
ll
Press and hold TRACK
or TRACK
forward or reverse a track.
Press
Press
nn to fast
temporarily stop USB playback.
ll// IIII toagain
to resume playback.
The following types of files are compatible:
• MP3 data
• WMA data
The following types of files are not compatible:
• WMA files that are protected by DRM (Digital Rights Management).
• WMA lossless format
• MP3 PRO format
• MP3 playlists
• WAV format
Playback Order
MP3/WMA playback sequence is based on order the files
are copied to the USB device and begins in the root folder.
Any empty folders or folders that do not include MP3/
WMA files are skipped. Depending on your software, the
playback order may vary.
Playback Capacity
• Maximum number of files: 48896
• Maximum number of folders: 127 plus the root directory
• Maximum number of files in each folder and root: 382
• Maximum number of folder levels (sub folders): 8
(7 levels plus the root)
Note: If the number of files/folders exceeds the maximum
outlined above, the additional files/folders will be ignored.
18
XDMA6415 OPERATION
USB Operation - MP3/WMA Files (Optional)
Additional MP3/WMA
Information
Sampling Frequency
Rates
MP3
WMA
Transfer Bit rates
MP3
WMA
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be played.
Do not attempt to play non-MP3/WMA files with the MP3/
WMA extension.
8kHz ~ 48kHz
32kHz ~ 48kHz
32kbps ~ 320kbps constant
Variable bit rates
48kbps ~ 192kbps constant
Variable bit rates
Note:
Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3 Tag Display
ID3 tags Version 1.x
This model will not display ID3 Version 2.0 or greater tags.
Note: If an invalid ID3 tag version is detected, "NO SUPPORT"
will scroll on the display.
19
XDMA6415 OPERATION
Operation of iPod
Connect iPod Device
(Not Included)
Use the included 2-wire cable to connect an iPod device to
the XDMA6415. Press MODE to select the operation of iPod
mode. Playback will begin automatically. If a song is playing
on the iPod device before it is connected, it will continue to
play.
Note: Both the USB and auxiliary input connections must be
made when connecting the 2-wire cable.
Displaying Information
Press DISP to select between elapsed time (default), track
number, clock, title, artist and album.
“UNKNOWN ARTIST” will be displayed if the file contains no
artist tag information.
“UNKNOWN ALBUM” will be displayed if the file contains no album tag information.
Search Functions
Playlist Search
Artist Name Search
Album Name Search
Song Name Search
Song Select
20
Press and hold SRCH for 3 seconds to enter the search
mode. Turn the volume knob to select between playlist,
artist, album and song. Press SRCH to select the desired
search type. Press BACK to access the previous level (up
one level).
Turn the volume knob to select between playlists. Press
SRCH to select desired playlist. Turn the volume knob to
select between songs from the chosen playlist. Press
to begin playback.
Turn the volume knob to select between artists. Press
SRCH to select desired artist. Turn the volume knob to
select between albums from the chosen artist. Press SRCH
to select desired album from the chosen artist. Turn the
volume knob to select between songs from the chosen
album. Press
to begin playback.
Turn the volume knob to select between albums. Press
SRCH to select desired album. Turn the volume knob to
select between songs from the chosen album. Press
to begin playback.
Turn the volume knob to select between songs. Press
to begin playback.
to skip to the beginning of the next song.
ll
to the beginning of the current song.
nnnnto return
again skips to the beginning of the previous
Press
Press
Pressing
song.
XDMA6415 OPERATION
Fast Forward
and Reverse
Pause
Intro
Repeat
Operation of iPod
Press and hold ll or nn to fast forward or reverse a
song.
Press
Press
temporarily stop playback.
ll// IIII toagain
to resume playback.
Press INT to play the first 10 seconds of each song.
Press INT again to cancel.
Press RPT to continuously repeat selected song.
Press RPT again to cancel.
It is not possible to select songs in repeat mode.
Random
Press RDM to play all songs in random order. Press RDM
again to cancel. Random mode is retained in memory when
selecting between Tuner, CD player, Aux, operation of iPod
and Bluetooth modes and when the unit is turned on/off. Character Support
Only alphanumeric characters can be displayed (ASCII type).
"NO SUPPORT" will be displayed if the file contains
characters that can not be displayed.
"NO SONG" will be displayed if there are no songs in the
selected playlist.
Maximum character display information
• Song title – 30 character maximum
• Artist name – 30 character maximum
• Album name – 30 character maximum
Note: Song title, artist name and album name will only be
displayed if included with the file.
iPod Device Compatibility
Compatible with
• iPod touch (2nd generation)
• iPod nano (4th generation)
• iPod classic
• iPod touch (1st generation)
• iPod nano (3rd generation)
• iPod nano (2nd generation)
• iPod with video
• iPod nano (1st generation)
Refer to your iPod device instruction manual for details on
how to obtain the latest software.
21
XDMA6415 OPERATION
Bluetooth® Operation
Overview
The XDMA6415 supports the HFP (hands-free profile), A2DP (advanced audio distribution
profile) and AVRCP (audio video remote control profile).
Preparation
Before you can use a mobile device with this head unit, it must be connected and
authenticated - commonly referred to as "pairing" a device. Please make sure that
Bluetooth is activated on your mobile device before you begin the pairing process. Refer
to the owner's manual of your mobile device for more details.
Bluetooth Pairing
1) To pair a Bluetooth enabled mobile phone to your head unit, press on the head unit,
or press MODE to enter Bluetooth mode. BLUETOOTH will scroll once, then STANDBY will
appear if a phone is not paired and connected.
2) Press and hold on the head unit for 5 seconds, until "PAIRING" is displayed. The
Bluetooth icon will flash every second. The head unit will begin to broadcast a signal for
60 seconds. 3) Complete the pairing from the Bluetooth menu of your mobile device by searching for
new devices. Please refer to your mobile device instructions for further information on
Bluetooth pairing and connections. The Bluetooth icon will illuminate solid.
The XDMA6415 device name is "DUAL BT." The password for the XDMA6415 is 1234. Connection Notes
•If ACNT is set to OFF, you must press
•From Bluetooth standby mode, press
•From Bluetooth standby mode, press
paired, but is not connected.
to connect after pairing.
to disconnect your mobile device.
to reconnect your mobile device if it has been
•To connect a different mobile device, the currently connected mobile device must be
disconnected. If this device has been paired previously, you may reconnect using the
mobile device's Bluetooth menu, or repeat the above pairing instructions.
General Note
•Due to the differences in Bluetooth technology, some mobile devices may be
incompatible or function improperly when used with the XDMA6415.
• The external Bluetooth microphone must be connected to the wiring harness at the rear
of the unit to enable correct operation of a Bluetooth phone call.
22
XDMA6415 OPERATION
Bluetooth® Operation
Description
Function
Press
Making a Phone Call
Last Number Dialing
Receiving a Phone
Call
once. An "_" will appear on the display.
Input the desired phone number using the 0-9, *, # buttons on the
remote control. Press to begin dialing.
A phone call may be placed from your mobile device using the
keypad, phone book or speed dial. When a call is placed from a
mobile device, “DIALING” will appear on the head unit display.
To enter last number dialing mode, press , then press a second
time. The head unit will display "LAST NUMBER DIAL."
Press DISP to cycle through the received, dialed or missed call
categories. Rotate the volume knob to cycle through the last 5 calls in
the selected category.
Press to begin dialing the selected number. “DIALING” will appear
on the head unit display.
If an incoming call is detected, the head unit will automatically switch
to Bluetooth mode, muting any audio that may be playing.
The incoming phone number will scroll across the display, the phone
icon will flash on the display and a ring tone will be audible from the
vehicle speakers. See Bluetooth Settings for speaker configurations.
Note: The ring audio level will depend the mobile device and head
unit ring volume and audio settings. If the ringer on the mobile device
is off, you may not hear an incoming ring tone.
Press on the head unit to receive a call. The phone icon will
illuminate solid.
Refusing a Call
During a Phone Call
Audio Transfer
Call Waiting
To refuse an incoming phone call, press and hold
for 3 seconds.
The head unit will display the elapsed time of the phone call.
The volume knob will adjust the volume of the call.
Press
momentarily to select between microphone on (MIC ON)
and microphone off (MUTE).
To transfer the phone call between the head unit and the mobile
device, press and hold DISP for 3 seconds during a call.
Tip: transfer audio to your mobile device before turning the head unit
off.
When a second call is incoming, press to activate call waiting. The
current call will be placed on hold, and the second call will be active.
Press again to return to the first call.
Call Hold
During a phone call, press to place the current call on hold. To
resume the phone call, press again.
Ending a Phone Call
Hold
for 3 or more seconds to end a call. If the phone call was received, the head unit will return to previous
mode when call is ended.
23
Bluetooth® Settings
Menu Function
Options
BT ON
Bluetooth Mode
BT OFF
ACNT ON
Auto Connect
ACNT OFF
AANS OFF
Auto Answer
Bluetooth Audio
AANS ON
SPK 2-CH
SPK 4-CH
Action
Enables Bluetooth mode. The Bluetooth icon will
flash every 10 seconds.
Disables Bluetooth support.
Allows reconnection to the most recently connected
mobile device. Note: Some mobile devices do not
support this feature.
Disables the auto connect feature. You must press
every time to connect a mobile device.
Disables the auto answer feature. Press to receive
an incoming call.
All incoming calls will be answered automatically without notification.
Directs the Bluetooth audio to the front speakers.
Directs the Bluetooth audio to all 4 speakers.
Bluetooth Streaming Audio Operation
(AV MODE)
The XDMA6415 supports A2DP wireless streaming audio from your Bluetooth mobile
device directly to your head unit. You can also control your music from the front panel of
the head unit using AVRCP.
To stream music to your head unit, your mobile device must support the following criteria:
• A2DP profile to stream audio
• AVRCP profile to control your music. Check the owner's manual or manufacturer of your device for compatibility.
• Streaming audio must be enabled from your mobile device. This option will vary depending on the device. Example: "wireless stereo." • Disabling AV MODE must be done from your mobile device.
After enabling streaming audio from a compatible mobile device, the head unit will display
"AV MODE." The following functions can be used to control music:
• The
• The
• The
• The
will skip to the next available audio track.
ll button
button will skip to the previous audio track.
nn
/ II button will toggle between play and pause during playback.
l
button will stop the audio playback.
Note: If experiencing problems with these functions, try playing music from mobile device.
On some mobile devices, it may be necessary to control the music from the device.
24
Limited One Year Warranty
This warranty gives you specific legal rights.
You may also have other rights which vary from
state to state.
Dual Electronics Corp. warrants this product to
the original purchaser to be free from defects in
material and workmanship for a period of one
year from the date of the original purchase.
Dual Electronics Corp. agrees, at our option,
during the warranty period, to repair any defect
in material or workmanship or to furnish an
equal new, renewed or comparable product
(whichever is deemed necessary) in exchange
without charges, subject to verification of the
defect or malfunction and proof of the date of
purchase. Subsequent replacement products
are warranted for the balance of the original
warranty period.
Who is covered? This warranty is extended to
the original retail purchaser for products
purchased and used in the U.S.A.
What is covered? This warranty covers all
defects in material and workmanship in this
product. The following are not covered:
installation/removal costs, damage resulting
from accident, misuse, abuse, neglect, product
modification, improper installation, incorrect
line voltage, unauthorized repair or failure to
follow instructions supplied with the product,
or damage occurring during return shipment of
the product.
What to do?
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any custom
controls may save you a service call.
2. If you require service during the warranty
period, you must carefully pack the product
(preferably in the original package) and ship
it by prepaid transportation with a copy of the
original receipt from the retailer to an
authorized service center.
3. Please describe your problem in writing and
include your name, a return UPS shipping
address (P.O. Box not acceptable), and a
daytime phone number with your shipment.
4. For more information and for the location of
the nearest authorized service center please
contact us by one of the following methods:
• Call us toll-free at 1-866-382-5476
• E-mail us at cs@dualav.com
Exclusion of Certain Damages: This warranty
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right,
claim or remedy in contract or tort, whether
or not arising from the company’s negligence,
actual or imputed. No person or representative
is authorized to assume for the company any
other liability in connection with the sale of
this product. In no event shall the company be
liable for indirect, incidental or consequential
damages.
25
XDMA6415 OPERATION
Troubleshooting - General
Problem
Unit will not turn on (no power)
Unit has power (but no sound)
Unit blows fuses
Excessive skipping
Cause
Action
Yellow wire not connected or incorrect voltage Check connections for proper
Red wire not connected or incorrect voltage
voltage (11~16VDC)
Black wire not connected
Check connection to ground
Fuse blown
Replace fuse
Speaker wires not connected
Check connections at speakers
One or more speaker wires touching each
other or touching chassis ground
Insulate all bare speaker wires from
each other and chassis ground
Yellow or red wire touching chassis ground
Check for pinched wire
Speaker wires touching chassis ground
Check for pinched wire
Incorrect fuse rating
Use fuse with correct rating
Unit is not mounted correctly or backstrap is
not secure
Check mounting sleeve and
backstrap support
Physical defect in media (CD, CD-R or CD-RW) Check media for scratches
ERROR-01 appears on display
Disc read error
Press EJECT or RESET
ERROR-02 appears on display
Focus error or disc is in upside down
Press EJECT or RESET
PROTECT appears on display
The WMA file is copy-protected by DRM
(Digital Rights Management)
Write disc using WMA files that are
not copy-protected
NO FILE appears on display
Selected file is not available in direct or
alphanumeric search modes
Repeat search using valid
parameters
INVALID appears on display
The file format is incompatible
Write disc using valid audio files
with .mp3 or .wma file extensions
CD mechanism position out of alignment
Press and hold EJECT for 3 seconds
to reset CD mechanism position
CD transit screws still in place
emove 2 transit screws located on
R
top of the unit
Pairing attempt has exceeded 60 seconds
Retry pairing sequence. Pairing
must complete within 60 seconds
Phone is not setup correctly to connect to a
bluetooth hands free device
Check the owners manual for
instructions on enabling bluetooth
An invalid ID3 tag version is present
Version 1.x ID3 tags are supported.
Version 2.0 or greater are not
supported
Unit will not accept a disc
PAIRING FAILED appears
on the display
NO SUPPORT appears on
display
26
XDMA6415 OPERATION
Specifications
CD Player
Frequency response: 10Hz-20kHz
Channel separation @ 1kHz: >65dB
D/A converter: 1 Bit
FM Tuner
Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 8.5dBf
50dB quieting sensitivity: 10dBf
Stereo separation @ 1kHz: 40dB
Frequency response: 30Hz-13kHz
AM Tuner
Tuning range: 530kHz-1710kHz
Usable sensitivity: 22uV
Frequency response: 30Hz-2.2kHz
General
Operating voltage: 11-16 VDC, negative ground
Speaker output impedance: 4~8 ohms
Line output voltage: 2 Volts
Dimensions: 7" x 7" x 2" (178 x 178 x 51 mm)
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 17 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms)
27
Dual Electronics Corp.
Toll Free: 1-866-382-5476
www.dualav.com
©2010 Dual Electronics Corp. All rights reserved.
Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States
and or other countries. Other trademarks and trade names are those of their respective owners.
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
“Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been certified by
the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
The Bluetooth ® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Namsung is under
license.
Other trademarks and trade names are those of their respective owners.
NSA0110-V02
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising