Shelti Original Assembly
Assembly Instructions
Thank you for purchasing a Shelti product. All of us at Shelti want you to be completely satisfied with
your Coin Pool Table, so feel free to contact us for help with the assembly of your product, Shelti parts,
or other information you may require.
Description
Shelti Pool Table Leg Box
Pool Table Leg Assembly
Pool Table Leg
Square Base T-Nut 1 3/8"x1 3/8"
#8 x 1 1/4" Pan Phil Tap Screw
Leg Leveler - Brushed Aluminum
Leg Bolts - 5/16-18x1 1/2"
Hex Washer Head - Slotted
Ball Set - With Magnet Cue Ball
Ball Rack Triangle
Pool Table Chalk
Pool Table Warranty Card
Coin Pool Table Assembly Instructions
Part Number
Quantity
LBA-0
PX-LAA-0
201-0053-0
305-0010-0
304-0002-0
204-0035-0
301-0020-0
1
4
4
4
4
4
12
1
1
1
6
1
1
213-0001-0
201-0060-0
210-0047-0
210-0063-0
210-0046-0
Step #1 - Place the pool table box
on its side, remove the banding
and the top of the box.
Step #2 - Slide the table partially out of the
box, slightly tip the table and remove the
bottom of the box and the fillers.
1
Step #3 - Attach the legs to the bottom of
the pool table using three 5/16”-18 leg
bolts per leg. Make sure that the leg
levelers are screwed all of the way into the
leg and slowly rotate the table over onto its
four legs.
Step #4 - Rough
level the pool
table by placing a
level across,
lengthwise, and
diagonally into the
four corners and
raise or lower the
appropriate leg
leveler. Final level
the pool table by
dropping a ball
onto the nose of
the cushion rail
and watch the
drift of the ball as
it comes to a stop.
Raise or lower the
appropriate leg
leveler until the
ball rolls true.
Step #5 - Complete the warranty card and return the self-mailing Registration Form to
Shelti in the event of upgrades and/or product recalls.
2
Maintenance Adjustments
Top Rail Molding Removal / Installation:
Step #1 - Remove the top rail molding screws.
Step #2 - Slide the molding all of
the way in one direction.
Step #3 - Lift the molding
on one end and slide it in
the opposite direction to
remove.
Cue Ball Separator Adjustment:
The magnet holder
should be flush to
the wall.
The lower track should be
spaced 63/64” away from the
magnet holder.
Loosen the screw and adjust
the oversize cue ball
separator shunt up or down
to properly separate oversize
cue balls.
3
Ball Trap Removal & Upper Ball Wedge Replacement:
To remove the ball trap, push the spring
loaded trap pin into the aluminum trap with
the blade of a screw driver while lifting up
and out on the trap.
Remove the three wood
screws to replace the upper
ball wedge.
Die Cast Corner Removal / Installation:
The bottom of the die
cast corner must be
removed to take the die
cast corner off of the
pool table.
Disconnect the trap spring
while removing the trap
from the pool table.
Adjust the ball stop in or out to properly
lock out the cue ball after the last ball is
made.
Remove the two selftapping 8/32 screws and
washers to change the
pocket liners.
Remove the two
3/8-16 x 2 1/2” hex
head bolts and
washers to remove
the die cast corner
from the top frame
assembly.
Remove the four
8/32 self-tapping
screws to
disassemble the die
cast corners.
4
Ball Trap Cam Removal / Adjustments:
The balls should
pass freely beside
the anti-cheat pin
when the ball trap
cam is at rest.
The acorn nut should be
adjusted so it is just above
the anti-cheat plate in the
resting position. There
needs to be enough space
so that the F-bracket can
move smoothly when the
coin-mech is actuated.
This view shows the ball trap cam at
rest with the balls trapped in the
ball trap.
The normal adjustment of the 5/16-18 carriage bolt
with brass bushing is in the center of the groove.
Adjust this bolt forward to increase the sensitivity
of the ball trap or back to decrease the sensitivity
of the trap.
This view shows the coin chute pushed in
rotating the ball trap cam into the back of the
aluminum ball trap which dumps the balls.
The anti-cheat pin should
stop the balls from leaving
the ball dump chute until the
coin chute is returned to its
original position.
The counter spring is pulled
as the coin chute is pushed
in actuating the counter.
For further information or questions contact Shelti Inc. at (989) 893-1739 or www.shelti.com.
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement