Control Mount
Instruction Manual
CM-IW2000
Introduction
Control Mount Rear Connection
The iPort® Control Mount is an in-wall mounting platform system
that allows an iPad® to become an integral part of your home
control system through wireless applications. Before installing
and using the CM-IW2000, please read and follow all of the
instructions in this manual carefully.
The CM-IW2000 features an RJ-45 jack to connect to the powered
wall plate via Cat5 cable. The power connection receives DC
power through the RJ45 connector as shown in figure 1.
System Capabilities:
Wiring Cat5/RJ-45 Cable
• Rigidly supports the iPad and provides a modern elegant
appearance
• Charges the iPad while it is mounted.
iPort Control Mount Box Contents:
(1) iPort in-wall mounting system (magnetic bezel and mounting frame)
(1) Power wall plate
(1) Regulated power supply
(1) Installation cut-out template
(1) Instruction manual
(1) Suction cup removal tool
(1) Circuit board assembly
(10) Machine screws with washers
To prepare the Cat5 cable and RJ-45 connector for iPort
installation:
1. Pull the Cat5 wire through the wall between the desired
locations.
2. Use a stripper or knife to strip about 1” of the cable jacket off
each end of the wire.
• Be careful not to nick any of the individual wires.
3. Untwist the wire pairs and spread them flat. Arrange them as
shown in Figure 2.
4. Trim the ends of the individual wires to ½” in length, making
sure they are even with each other. Flatten the wires against
each other, leaving no space between them.
Required Tools
The following tools are required to install the iPort:
•
•
•
•
•
The Cat5 cable and RJ-45 connector used in iPort installations
must be wired according to the T568A (“Straight-Through”)
Standard with cables wired identically at both ends.
5. Hold the RJ-45 connector clip-side down and insert the Cat5
wire ends firmly into the connector. Make sure that all the wires
are flat all the way to the very front of the connector.
#1 Phillips screwdriver
#2 Phillips screwdriver
Wire cutters and wire strippers
RJ-45 cable crimp tool and modular connectors
Sheet rock saw (for retrofitting into an existing wall)
6. Re-confirm the color orientation matches the diagram and
cable jacket fits against the connector stop.
Selecting an Installation Location
The iPort Control Mount is designed for use in normal interior
environments. When selecting location for the Control Mount,
please consider the following:
7. Firmly crimp the RJ-45 connector with the crimp tool. Confirm
the connector is crimped firmly and all the wires are flat right up
against the front of the connector. If even one of these wires is
incorrect, cut the connector off the cable and repeat steps 2 – 7
with a new RJ-45 connector.
• Do not use the Control Mount outside or in a humid or wet
environment. It is not waterproof or water-resistant.
• The Control Mount cut-out must have enough depth within
the wall cavity for the Control Mount and its connections.
• Check for a strong Wi-Fi signal at the mounting location using
the iPad that is to be installed in the Control Mount.
POWER
WIRELESS
INTERNET
ETHERNET PORT
1
2
3
4
CM-IW100T
RJ-45 Jack
®
U.S. Patent No. 7,493,142
Additional Patents Pending
Designed and Engineered in the USA
33-5203 4-09
To Audio
Wall Plate
Figure 1: iPort Rear Connection
2
Figure 2: RJ-45 Power Connector
CM-IW2000 Instruction Manual
Installation Preparation
iPort Connection and Installation
The CM-IW2000 features an integral Roto-Lock mounting
system for quick mounting directly into existing walls. Once the
hole is cut and the cables have been run, you can install the iPort
into the wall in a matter of seconds.
1. Determine the location for the iPort Control Mount and the
wall plate.
®
2. Perform an obstruction survey to ensure there are no studs,
conduit, pipes, heating ducts, or air returns that will interfere
with the Control Mount.
3. Find the cut-out template provided in the CM-IW2000
packaging. Place in appropriate location between wall studs.
Verify there are no horizontal fire blocks with-in cut out area.
Place level on template to assure a level opening. Position the
template where the Control Mount is to be located and pencil
an outline on the wall.
Note: Be sure to confirm the installation of the iPort at this
time for either vertical (portrait) or horizontal (landscape)
orientation. Certain applications of the mounted iPad work
only in one orientation, so be sure to confirm the client’s
requirements before cutting the hole.
• If you are unsure about obstructions, drill a small hole in the
center of the outline and insert a coat hanger wire into the
hole to feel around for possible obstructions.
4.Cut the opening using a drywall saw.
See Figure 3
1. Before making connections, run a length of Cat5 cable through
the wall from the Control Mount location to the power wall plate
location, as shown in Figure 3. The wall plate can be located up
to 30 feet from the control mount.
2. Install RJ-45 connectors on both ends of the Cat5 cable as
explained in Figure 2: Cat5 / RJ-45 Power connector. The Cat5/
RJ-45 cable pin assignment is:
Pin
Pin
Pin
Pin
1: 2:
3:
4:
Unused
Unused
Unused
Unused
Pin
Pin
Pin
Pin
5:
6:
7:
8:
Unused
Unused
Ground
+15V
3. Plug the Cat5 cable into the RJ-45 jack on the Control Mount
and the RJ-45 jack on the wall plate, as shown in Figure 3.
4. Install the wall plate into an electrical box
Important: Do not install the iPort’s wall plate in the same
electrical box as AC house wiring, a light switch, or any other highvoltage device or control. The wall plate can share gang boxes
with other iPort Control Mount wall plates or with controls such
as A/B speaker switches, infrared receivers, and volume controls,
if these other devices are rated as Class 2 devices according to the
National Electrical Code.
5. After cutting the opening, make sure the edges of opening
are smooth so frame flange will rest flat against wall.
POWER
WIRELESS
INTERNET
ETHERNET PORT
1
2
3
4
CM-IW100T
®
U.S. Patent No. 7,493,142
Additional Patents Pending
Designed and Engineered in the USA
33-5203 4-09
To Audio
Wall Plate
Figure 3: iPort System Connections
CM-IW2000 Instruction Manual
3
5. Prior to placing the mounting frame into the wall, pull a sufficient
length of the Cat5 cable and its attached RJ-45 connector
through the opening in the side of the mounting frame, as
shown in figure 4.
10. Mount iPad to the Bezel by placing iPad into nesting area on
rear of bezel and attach metal retainer with ten (10) machine
screws and washers as shown in figure 6 with the #1 Phillips
screwdriver
Note: Do not overtighten the retaining screws.
Overtightening may cause bezel damage
Figure 4: Mounting Frame
6. The retainer and cradle are pre-assembled with internal
packaging materials. Disassemble by removing the four screws.
Discard the foam block and card insert.
Figure 5: Roto-Lock Screw Locations
8. Insert the Control Mount mounting frame into the opening in
the wall.
9. Hand-tighten the four Roto-Lock screws on the Control Mount’s
mounting frame as shown in Figure 5. The Roto-Lock clamps will
automatically rotate into position behind the wall and begin
clamping the mount.
Note: The Roto-Lock system can accommodate wall thickness
of 3/8” to 3/4” and can be extended to 1 1/4” with the
removal of the toggle caps.
• When you notice resistance on the four screws, the Control
Mount has been clamped successfully.
Important: NEVER over-tighten the Roto-Lock screws.
Figure 6: Mounting iPad to Bezel
4
CM-IW2000 Instruction Manual
11. Attach safety lanyard on top center screw of retainer assembly
as shown in figure 7.
Final Adjustment
12.Install pre-assembled circuit board assembly into the iPad dock
connector on end of iPad. Metal circuit board bracket will slide
under thumb screws on the retainer. Tighten thumb screws to
secure circuit board assembly to retainer.
1. Mounting frame is supplied with a preset magnet height setting.
The preset adjustment will likely result with a space between
the bezel and the wall surface. To adjust the magnet height
setting, turn magnet screws clockwise, one turn at a time, until
bezel fits snugly against the wall as shown in figure 9.
13.Remove thumbscrew from the interior of metal frame, install
though eyelet at the end of cable lanyard , and fasten lanyard
to central hole at top of metal frame.
2. Insert assembly into frame and adjust until desired results are
accomplished.
14.Connect the Cat5 cable from the wall to the iPad connector
board as noted in figure 8.
When removing iPad assembly from magnetic frame,
always use suction cup removal tool provided as shown in
figure 10. Always attach suction cup to upper right or left
corner of iPad.
Figure 7: Attaching Safety Lanyard.
3. Plug the included DC power supply into the Power connector
on the wall plate and into a wall outlet, as shown in Figure 3.
Note: To sync your iPad with your computer, please follow
the steps above in reverse order to remove the iPad and
sync. Once your synchronization is complete, reinstall the
iPad and follow the steps to reassemble.
Figure 9: Magnet Height Screws
Figure 8: Attaching Cat5/RJ45 cable.
CM-IW2000 Instruction Manual
5
Removal
Operation
1. Ensure that the CM2000 bezel is not bonded with the wall paint.
If it has, gently place a plastic putty knife under the frame on
all sides to ensure the frame doesn’t peel the wall paint while
being removed.
Once installed, the iPad is now fully functional. The iPort Control
Mount features a button to control the Power functionality. To
activate the Power function, press the button as noted in figure 11.
2. Attach the iPort suction cup removal tool (figure 10) to the
UPPER left or right corner of the iPad touch screen.
3.Carefully pull the iPad away from the wall. The iPad and
mounting assembly will detach from the wall. Disconnect the
CAT5 cable.
The operation of the iPad touch screen to choose applications,
music, email or internet remains the same.
Note: For questions regarding the touchscreen functions of
your iPad, please visit: www.apple.com
4. Detach the safety lanyard from the back of the iPad mounting
assembly.
5. Place the iPad mounting assembly facedown on a clean, smooth
surface and remove the remaining machine screws.
6. Carefully separate the iPad from the mounting assembly.
Reserve the machine screws in a safe location. The screws are
needed for re-installation.
Figure 10: Suction Cup Removal Tool
6
Figure 11: Power Button
CM-IW2000 Instruction Manual
Specifications
Power supply:
15V DC, regulated
Dimensions (W x H x D):11.60” x 9.51” x 2.36” (294.6mm x 241.6mm x 59.9mm)
219.7mm
8.65in
10.75” x 8.65” (273.1mm x 219.7mm)
241.6mm
9.51in
Cut-out Dimensions (W x H):
273.1mm
10.75in
294.6mm
11.60in
219.7mm
8.65in
6.1mm
0.24in
273.1mm
10.75in
38mm
1.49in
59.9mm
2.36in
CM-IW2000 Instruction Manual
7
LIMITED ONE (1) YEAR WARRANTY
iPort warrants to the first end-user purchaser that this iPort-brand product (“Product”), when purchased from and installed by an
authorized iPort Dealer/Distributor, will be free from defective workmanship and materials in the initial installation for the period stated
below. iPort will at its option and expense during the warranty period, either repair the defect or replace the Product with a new or
remanufactured Product or a reasonable equivalent at no charge for parts, labor and return shipping.
EXCLUSIONS
TO THE EXTENT PERMITTED BY LAW, THE WARRANTY SET FORTH ABOVE IS IN LIEU OF, AND EXCLUSIVE OF, ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, AND IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED BY IPORT. ALL OTHER EXPRESS
AND IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IMPLIED WARRANTY OF FITNESS
FOR USE, AND IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. No one is authorized to make or modify any warranties on behalf of iPort.
The warranty stated above is the sole and exclusive remedy and iPort’s performance shall constitute full and final satisfaction of all
obligations, liabilities and claims with respect to the Product. IN ANY EVENT, IPORT SHALL NOT BE LIABLE FOR CONSEQUENTIAL,
INCIDENTAL, ECONOMIC, PROPERTY, BODILY INJURY, OR PERSONAL INJURY DAMAGES ARISING FROM THE PRODUCT, ANY
BREACH OF THIS WARRANTY OR OTHERWISE.
This warranty statement gives you specific legal rights, and you may have other rights which vary from state to state. Some states
do not allow the exclusion of implied warranties or limitations of remedies, so the above exclusions and limitations may not apply. If
your state does not allow disclaimer of implied warranties, the duration of such implied warranties is limited to the period of iPort’s
express warranty.
______________________________________________________________________________
Your Product Model and Description: iPort Control Mount CM-IW2000
Warranty Period for this Product: One (1) year from the date on the original sales receipt, invoice or other satisfactory proof of
purchase.
Additional limitations and Exclusions From Warranty Coverage: The warranty described above is non-transferrable, and does not
include damage to allied or associated equipment which may result for any reason from use with this Product, and does not include
Product failure caused by accident, disaster, negligence, improper installation, misuse (e.g. overdriving the amplifier or speaker,
excessive heat or cold or humidity, outdoor installation), or from service or repair which has not been authorized by iPort.
Obtaining Authorized Service: If you purchased your iPort from an iPort Dealer, you (1) must contact your authorized iPort Dealer/
Installer or call iPort Customer Service at (800) 582-0772 within the warranty period, (2) must obtain a return merchandise number
(RMA), and (3) deliver the Product to iPort shipping prepaid during the warranty period, together with the original sales receipt,
invoice or other satisfactory proof of purchase from your iPort Dealer. If you did not purchase from an iPort dealer, you must contact
your authorized seller within the warranty period and obtain instructions for obtaining authorized service.
san clemente ca | 888 . 45 . iPort | www.iportmusic.com
©2010 Dana Innovations. All rights reserved.
iPort and Roto-Lock are registered trademarks of Dana Innovations.
iPad is a trademark or registered trademark of Apple Inc. “Made for iPad” means that an electronic accessory has been
designed to connect specifically to iPad, and has been certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Due to continuous product improvement,
all specifications are subject to change without notice.
For the latest iPort product information go to www.iportmusic.com
8
33-5488
08162010
">