Daikin | FH(Y)125BVE | Specifications | Daikin FH(Y)125BVE Specifications

Daikin FH(Y)125BVE Specifications
00_CV_3P170549-4C.fm Page 1 Tuesday, November 6, 2007 9:30 AM
OPERATION MANUAL
English
SPLIT SYSTEM
Air Conditioner
Español
MODELS
(Ceiling suspension type)
FH(Y)35BVE
FH(Y)50BVE
FH(Y)60BVE
FH(Y)71BVE
FH(Y)100BVE
FH(Y)125BVE
00_CV_3P170549-4C.fm Page 3 Tuesday, November 6, 2007 9:30 AM
Thank you for purchasing this Daikin air conditioner. Carefully read this operation manual
before using the air conditioner. It will tell you
how to use the unit properly and help you if any
trouble occurs. After reading the manual, file it
away for future reference.
Le agradecemos la compra de este acondicionador de aire Daikin.
Lea cuidadosamente el manual de funcionamiento antes de utilizar el acondicionador de
aire. Dicho manual le indicará cómo utilizar adecuadamente la máquina y le ayudará en caso
de avería. Después de leer el manual, consérvelo para consultas futuras.
00_CV_3P170549-4C.fm Page 2 Tuesday, November 6, 2007 9:30 AM
5 12
4
2
1
3
7
hr
C
hr
6
8
NOT
AVAILABLE
TEST
9
11
10
13
L H
14
21
20
TEST
19
17
15
16
18
22
1
R35, 50
RY35
R60
RY50, 60
f
a
k
e
e
i
R(Y)100, 125
3
g
h
d
d
j
R(Y)71
b
d
c
e
f
hr
C
k
2
[1]
4
H
01_en_3P170549-4C.fm Page 1 Tuesday, November 6, 2007 9:36 AM
CONTENTS
ILLUSTRATION .................................................. [1]
1. WHAT TO DO BEFORE OPERATION.......... 1
2. SAFETY PRECAUTIONS.............................. 2
3. OPERATION RANGE.................................... 4
4. INSTALLATION SITE .................................... 4
5. NAME AND FUNCTION OF EACH SWITCH
AND DISPLAY ON THE REMOTE
CONTROLLER .............................................. 5
6. OPERATION PROCEDURE.......................... 6
7. OPTIMUM OPERATION................................ 8
8. MAINTENANCE
(FOR SERVICE PERSONNEL)..................... 9
9. NOT MALFUNCTION OF THE AIR
CONDITIONER............................................ 10
10. TROUBLE SHOOTING................................ 11
11. SPECIFICATIONS....................................... 13
1. WHAT TO DO BEFORE OPERATION
This operation manual is for the following systems
with standard control. Before initiating operation,
contact your Daikin dealer for the operation that corresponds to your system.
PRECAUTIONS FOR GROUP CONTROL
SYSTEM OR TWO REMOTE CONTROLLER
CONTROL SYSTEM
This system provides two other control systems
beside individual control (one remote controller controls one indoor unit) system. Confirm the following if
your unit is of the following control system type.
• Group control system
One remote controller controls up to 16 indoor
units.
All indoor units are equally set.
• Two remote controller control system
Two remote controllers control one indoor unit (In
case of group control system, one group of indoor
units)
The unit is individually operated.
NOTE
• Contact your Daikin dealer in case of changing
the combination or setting of group control and
two remote controller control systems.
Names and functions of parts
Refer to figure 2 on page [1]
Indoor unit
Outdoor unit
Unit with
remote
controller
Unit without remote
controller
(When used as
simultaneous
operation system)
NOTE
• If the unit you purchased is controlled by a wireless remote controller, also refer to the wireless
remote controller’s operation manual.
a
b
c
d
e
f
g
h
i
j
k
If your installation has a customized control system,
ask your Daikin dealer for the operation that corresponds to your system.
Indoor unit
Outdoor unit
Remote controller
Inlet air
Discharged air
Air outlet
Air flow flap (at air outlet)
Refrigerant piping, connection electric wire
Drain pipe
Air inlet
The built-in air filter removes dust and dirt.
Ground wire
Wire to ground from the outdoor unit to prevent electrical shocks.
• Heat pump type
This system provides cooling, heating, automatic,
program dry, and fan operation modes.
• Cooling only type
This system provides cooling, program dry, and
fan operation modes.
1
English
01_en_3P170549-4C.fm Page 2 Tuesday, November 6, 2007 9:36 AM
2. SAFETY PRECAUTIONS
To gain full advantage of the air conditioner’s functions and to avoid malfunction due to mishandling,
we recommend that you read this instruction manual
carefully before use.
This air conditioner is classified under “appliances not
accessible to the general public”.
• The precautions described herein are classified as WARNING and CAUTION. They both
contain important information regarding
safety. Be sure to observe all precautions
without fail.
WARNING .. Failure to follow these instructions
properly may result in personal
injury or loss of life.
CAUTION ... Failure to observe these instructions properly may result in property damage or personal injury,
which may be serious depending
on the circumstances.
• After reading, keep this manual in a convenient place so that you can refer to it whenever
necessary. If the equipment is transferred to a
new user, be sure also to hand over the manual.
WARNING
Be aware that prolonged, direct exposure to
cool or warm air from the air conditioner, or
to air that is too cool or too warm can be
harmful to your physical condition and
health.
When the air conditioner is malfunctioning
(giving off a burning odour, etc.) turn off
power to the unit and contact your local
dealer.
Continued operation under such circumstances
may result in a failure, electric shocks or fire hazards.
Consult your local dealer about installation
work.
Doing the work yourself may result in water leakage, electric shocks or fire hazards.
Consult your local dealer regarding modification, repair and maintenance of the air conditioner.
Improper workmanship may result in water leakage, electric shocks or fire hazards.
Do not place objects, including rods, your
fingers, etc., in the air inlet or outlet.
Injury may result due to contact with the air conditioner’s highspeed fan blades.
English
Beware of fire in case of refrigerant leakage.
If the air conditioner is not operating correctly,
i.e. not generating cool or warm air, refrigerant
leakage could be the cause.
Consult your dealer for assistance.
The refrigerant within the air conditioner is safe
and normally does not leak.
However, in the event of a leakage, contact with
a naked burner, heater or cooker may result in
generation of noxious gas.
Do not longer use the air conditioner until a qualified service person confirms that the leakage
has been repaired.
Consult your local dealer regarding what to
do in case of refrigerant leakage.
When the air conditioner is to be installed in a
small room, it is necessary to take proper measures so that the amount of any leaked refrigerant does not exceed the concentration limit in the
event of a leakage. Otherwise, this may lead to
an accident due to oxygen depletion.
Contact professional personnel about
attachment of accessories and be sure to
use only accessories specified by the manufacturer.
If a defect results from your own workmanship, it
may result in water leaks, electric shock or fire.
Consult your local dealer regarding relocation and reinstallation of the air conditioner.
Improper installation work may result in leakage,
electric shocks or fire hazards.
Be sure to use fuses with the correct ampere
reading.
Do not use improper fuses, copper or other wires
as a substitute, as this may result in electric
shock, fire, injury or damage to the unit.
Be sure to earth the unit.
Do not earth the unit to a utility pipe, lightning
conductor or telephone earth lead. Imperfect
earthing may result in electric shocks or fire.
A high surge current from lightning or other
sources may cause damage to the air conditioner.
Be sure to install an earth leakage breaker.
Failure to install an earth leakage breaker may
result in electric shocks, or fire.
Consult the dealer if the air conditioner submerges owing to a natural disaster, such as a
flood or typhoon.
Do not operate the air conditioner in that case, or
otherwise a malfunction, electric shock, or fire
may result.
Do not start or stop operating the air conditioner with the power supply breaker turned
ON or OFF.
Otherwise, fire or water leakage may result.
Furthermore, the fan will rotate abruptly if power
failure compensation is enabled, which may
result in inlury.
2
01_en_3P170549-4C.fm Page 3 Tuesday, November 6, 2007 9:36 AM
Do not use the product in the atmosphere
contaminated with oil vapor, such as cooking
oil or machine oil vapor.
Oil vapor may cause crack damage, electric
shocks, or fire.
Do not use the product in places with excessive oily smoke, such as cooking rooms, or
in places with flammable gas, corrosive gas,
or metal dust.
Using the product in such places may cause fire
or product failures.
Do not use flammable materials (e.g., hairspray or insecticide) near the product.
Do not clean the product with organic solvents such as paint thinner.
The use of organic solvents may cause crack
damage to the product, electric shocks, or fire.
Be sure to use a dedicated power supply for
the air conditioner.
The use of any other power supply may cause
heat generation, fire, or product failures.
CAUTION
Do not use the air conditioner for purposes
other than those for which it is intended.
Do not use the air conditioner for cooling precision instruments, food, plants, animals or works
of art as this may adversely affect the performance, quality and/or longevity of the object
concerned.
Do not remove the outdoor unit’s fan guard.
The guard protects against the unit’s high speed
fan, which may cause injury.
To avoid oxygen depletion, ensure that the
room is adequately ventilated if equipment
such as a burner is used together with the air
conditioner.
After prolonged use, check the unit stand
and its mounts for damage.
If left in a damaged condition, the unit may fall
and cause injury.
Do not place flammable sprays or operate
spray containers near the unit as this may
result in fire.
Before cleaning, be sure to stop unit operation, turn the breaker off or remove the power
cord.
Otherwise, an electric shock and injury may
result.
To avoid electric shocks, do not operate with
wet hands.
Do not place objects that are susceptible to
moisture directly beneath the indoor or outdoor units.
Under certain conditions, condensation on the
main unit or refrigerant pipes, air filter dirt or
drain blockage may cause dripping, resulting in
fouling or failure of the object concerned.
3
Do not place appliances that produce naked
flames in places exposed to the air flow from
the unit as this may impair combustion of the
burner.
Do not place heaters directly below the unit,
as resulting heat can cause deformation.
Do not allow a child to mount on the outdoor
unit or avoid placing any object on it.
Falling or tumbling may result in injury.
Do not block air inlets nor outlets.
Impaired air flow may result in insufficient performance or trouble.
Be sure that children, plants or animals are
not exposed directly to airflow from the unit,
as adverse effects may ensue.
Do not wash the air conditioner with water,
as this may result in electric shocks or fire.
Do not install the air conditioner at any place
where there is a danger of flammable gas
leakage.
In the event of a gas leakage, build-up of gas
near the air conditioner may result in fire hazards.
Do not put flammable containers, such as
spray cans, within 1 m from the blow-off
mouth.
The containers may explode because the warm
air output of the indoor or outdoor unit will affect
them.
Arrange the drain hose to ensure smooth
drainage.
Imperfect drainage may cause wetting.
The appliance is not intended for use by
unattended young children or infirm persons.
Impairment of bodily functions and harm to
health may result.
Children should be supervised to ensure that
they do not play with the unit or its remote
controller.
Accidental operation by a child may result in
impairment of bodily functions and harm health.
Do not let children play on or around the outdoor unit.
If they touch the unit carelessly, injury may be
caused.
Consult your dealer regarding cleaning the
inside of the air conditioner.
Improper cleaning may cause breakage of plastic parts, water leakage and other damage as
well as electric shocks.
To avoid injury, do not touch the air inlet or
aluminium fins of the unit.
English
01_en_3P170549-4C.fm Page 4 Tuesday, November 6, 2007 9:36 AM
Do not place objects in direct proximity of the
outdoor unit and do not let leaves and other
debris accumulate around the unit.
Leaves are a hotbed for small animals which can
enter the unit. Once in the unit, such animals can
cause malfunctions, smoke or fire when making
contact with electrical parts.
Never touch the internal parts of the controller.
Do not remove the front panel. Touching certain
internal parts will cause electric shocks and
damage to the unit. Please consult your dealer
about checking and adjustment of internal parts.
Do not leave the remote controller wherever
there is a risk of wetting.
If water gets into the remote controller there is a
risk of electrical leakage and damage to electronic components.
Watch your steps at the time of air filter
cleaning or inspection.
High-place work is required, to which utmost
attention must be paid.
If the scaffold is unstable, you may fall or topple
down, thus causing injury.
HEAT PUMP TYPE
OUTDOOR
UNIT
COOLING
RY35FV1A
HEATING
COOLING
RY50 60GAV1A
HEATING
RY71 100 125FUV1/Y1
If the temperature or the humidity is beyond the following conditions, safety devices may work and the
air conditioner may not operate, or sometimes,
water may drop from the indoor unit.
COOLING ONLY TYPE
TEMPERATURE [°C]
OUTDOOR UNIT
OUTDOOR
INDOOR
21 to 32 (DB)/
R35 50 60GV1(A) 19.4 to 46 (DB)
14 to 23 (WB)
R71 100 125
21 to 35 (DB)/
21 to 52 (DB)
FUV1/Y1
14 to 25 (WB)
21 to 32 (DB)/
R50 60GVAL
19.4 to 54 (DB)
14 to 23 (WB)
R71 100 125
21 to 35 (DB)/
FUVAL/TAL
21 to 50 (DB)
14 to 25 (WB)
KUYAL
R71 100 125 140KUV1/Y1
21 to 35 (DB)/
21 to 46 (DB)
LUV1/Y1/VAL/TAL/
14 to 25 (WB)
YAL
R71 100 21 to 35 (DB)/
21 to 46 (DB)
14 to 25 (WB)
125KUVAL/TAL
English
COOLING
HEATING
COOLING
RY50 60GVAL
HEATING
RY71 100 125FUVAL/TAL
3. OPERATION RANGE
OPERATION
RY71 100 125 140KUV1/Y1
LUV1/Y1/TAL/
YAL
COOLING
HEATING
COOLING
HEATING
TEMPERATURE [°C]
OUTDOOR
INDOOR
21 to 32 (DB)/
19.4 to 46 (DB)
14 to 23 (WB)
–9 to 21 (DB)/
15 to 28 (DB)
–10 to 15.5 (WB)
21 to 32 (DB)/
19.4 to 46 (DB)
14 to 23 (WB)
–9 to 21 (DB)/
14 to 28 (DB)
–10 to 15 (WB)
21 to 35 (DB)/
–5 to 52 (DB)
14 to 25 (WB)
–9 to 21 (DB)/
15 to 27 (DB)
–10 to 15.5 (WB)
21 to 32 (DB)/
19.4 to 54 (DB)
14 to 23 (WB)
–9 to 21 (DB)/
14 to 28 (DB)
–10 to 15 (WB)
21 to 35 (DB)/
–5 to 54 (DB)
14 to 25 (WB)
–9 to 21 (DB)/
15 to 24 (DB)
–10 to 15.5 (WB)
21 to 35 (DB)/
–5 to 46 (DB)
12 to 25 (WB)
–9 to 21 (DB)/
15 to 27 (DB)
–10 to 15 (WB)
D B: Dry bulb temperature
WB: Wet bulb temperature
The setting temperature range of the remote controller is 16°C to 32°C.
4. INSTALLATION SITE
Regarding places for installation
• Is the air conditioner installed at a well-ventilated
place where there are no obstacles around?
• Do not use the air conditioner in the following
places.
a.Filled with much mineral oil such as cutting oil
b.Where there is much salt such as a beach area
c.Where sulfured gas exists such as a hot-spring
resort
d.Where there are considerable voltage fluctuations such as a factory or plant
e.Vehicles and vessels
f .Where there is much spray of oil and vapor such
as a cookery, etc.
g.Where there are machines generating electromagnetic waves
h.Filled with acid and/or alkaline steam or vapor
4
01_en_3P170549-4C.fm Page 5 Tuesday, November 6, 2007 9:36 AM
• Is a snow protection measure taken?
For details, consult your dealer.
1
Regarding wiring
• All wiring must be performed by an authorized
electrician.
To do wiring, ask your dealer. Never do it by yourself.
• Make sure that a separate power supply circuit is provided for this air conditioner and
that all electrical work is carried out by qualified personnel according to local laws and
regulations.
2
3
4
DISPLAY “
” “ ”“
”“
”
(VENTILATION/AIR CLEANING)
This display shows that the total heat
exchange and the air cleaning unit are in
operation (These are optional accessories).
5
DISPLAY “ ” “ ” “ ” “ ” “ ”
(OPERATION MODE)
This display shows the current OPERATION
MODE. For cooling only type, “ ” (Auto)
and “ ” (Heating) are not installed.
6
TEST” (INSPECTION/TEST
DISPLAY “
OPERATION)
When the INSPECTION/TEST OPERATION
BUTTON is pressed, the display shows the
system mode is in.
Pay attention to running noises, too
• Are the following places selected?
a. A place that can sufficiently withstand the
weight of the air conditioner with less running
noises and vibrations.
b. A place where the hot wind discharged from the
air outlet of the outdoor unit and the running
noises.
• Are you sure that there are no obstacles near
the air outlet of the outdoor unit?
Such obstacles may result in declined performance and increased running noises.
• If abnormal noises occur in use, consult your
dealer.
hr
DISPLAY “
” (PROGRAMMED TIME)
hr
7
This display shows the PROGRAMMED TIME
of the system start or stop.
Regarding drainage of drain piping
• Is the drain piping executed to perform complete drainage?
If proper drainage is not carried out from the outdoor drain pipes during air-conditioning operation,
chances are that dust and dirt are clogged in the
pipe. This may result in a water leakage from the
indoor unit. Under such circumstances, stop the
operation of the air conditioner, and then consult
your dealer or our service station.
ON/OFF BUTTON
Press the button and the system will start.
Press the button again and the system will
stop.
OPERATION LAMP (RED)
The lamp lights up during operation.
DISPLAY “
” (UNDER CENTRALIZED CONTROL)
When this display shows, the system is
UNDER CENTRALIZED CONTROL.
8
DISPLAY “
” (SET TEMPERATURE)
This display shows the set temperature.
9
DISPLAY “
” (FAN SPEED)
This display shows the set fan speed.
C
DISPLAY “ ” (AIR FLOW FLAP)
10 Refer to “ADJUSTING THE AIR FLOW
DIRECTION”.
DISPLAY “
” (TIME TO CLEAN AIR FIL11 TER)
Refer to “HOW TO CLEAN THE AIR FILTER”.
5. NAME AND FUNCTION OF EACH
SWITCH AND DISPLAY ON THE
REMOTE CONTROLLER
Refer to figure 1 on page [1]
The illustrations in this operating manual correspond to the remote control format BRC1C type.
Although the display and shape of the buttons on the
BRC1B type are slightly different, they may be operated in the same manner.
DISPLAY “
” (DEFROST)
Refer to “DEFROST OPERATION”.
NON-FUNCTIONING DISPLAY
If that particular function is not available, pressing the button may display the words “NOT
AVAILABLE” for a few seconds.
13 When running multiple units simultaneously
The “NOT AVAILABLE” message will only be
appear if none of the indoor units is equipped
with the function. If even one unit is equipped
with the function, the display will not appear.
12
14
5
TIMER MODE START/STOP BUTTON
Refer to “PROGRAM TIMER OPERATION”.
English
01_en_3P170549-4C.fm Page 6 Tuesday, November 6, 2007 9:36 AM
15
16
17
18
19
20
21
22
TIMER ON/OFF BUTTON
Refer to “PROGRAM TIMER OPERATION”.
INSPECTION/TEST OPERATION BUTTON
This button is used only by qualified service
persons for maintenance purposes.
PROGRAMMING TIME BUTTON
Use this button for programming “START and/
or STOP” time.
TEMPERATURE SETTING BUTTON
Use this button for SETTING TEMPERATURE.
FILTER SIGN RESET BUTTON
Refer to “HOW TO CLEAN THE AIR FILTER”.
FAN SPEED CONTROL BUTTON
Press this button to select the fan speed,
HIGH or LOW, of your choice.
OPERATION MODE SELECTOR BUTTON
Press this button to select OPERATION MODE.
AIR FLOW DIRECTION ADJUST BUTTON
Refer to “ADJUSTING THE AIR FLOW
DIRECTION”.
NOTE
• For the sake of explanation, all indications are
shown on the display in Figure 1 contrary to
actual running situations.
6. OPERATION PROCEDURE
Refer to figure 1 on page [1]
• Operating procedure varies with heat pump type
and cooling only type. Contact your Daikin dealer
to confirm your system type.
• To protect the unit, turn on the main power switch
6 hours before operation.
• If the main power supply is turned off during operation, operation will restart automatically after the
power turns back on again.
COOLING, HEATING, AUTOMATIC, FAN,
AND PROGRAM DRY OPERATION
Operate in the following order.
1
OPERATION MODE SELECTOR
Press OPERATION MODE SELECTOR button several times and select the OPERATION MODE of your choice as follows.
COOLING OPERATION ......................... “
HEATING OPERATION .......................... “
AUTOMATIC OPERATION ..................... “
English
• In this operation mode, COOL/HEAT
changeover is automatically conducted.
FAN OPERATION................................... “ ”
DRY OPERATION .................................. “ ”
• The function of this program is to decrease the
humidity in your room with the minimum temperature decrease.
• Micro computer automatically determines
TEMPERATURE and FAN SPEED.
• This system does not go into operation if the
room temperature is below 16°C.
Refer to figure 3 on page [1]
• For cooling only type, “COOLING” , “FAN” and
“DRY” operation are able to select.
2
ON/OFF
Press ON/OFF button
OPERATION lamp lights up or goes off and the system starts or stops OPERATION.
[EXPLANATION OF HEATING OPERATION]
DEFROST OPERATION
• As the frost on the coil of an outdoor unit increase,
heating effect decreases and the system goes
into DEFROST OPERATION.
• The indoor unit fan stops and the remote controller display shows “
”.
• After 6 to 8 minutes (maximum 10 minutes) of
DEFROST OPERATION, the system returns to
HEATING OPERATION.
Regarding outside air temperature and heating capacity
• The heating capacity of the air conditioner
declines as the outside air temperature falls. In
such a case, use the air conditioner in combination with other heating systems.
• A warm air circulating system is employed, and
therefore it takes some time until the entire room
is warmed up after the start of operation.
• An indoor fan runs to discharge a gentle wind
automatically until the temperature inside the air
conditioner reaches a certain level. At this time,
the remote controller displays “
”. Leave it
as it stands and wait for a while.
• When the warm air stays under the ceiling and
your feet are cold, we recommend that you use a
circulator (a fan to circulate the air inside the
room). For details, consult your dealer.
”
”
”
6
01_en_3P170549-4C.fm Page 7 Tuesday, November 6, 2007 9:36 AM
ADJUSTMENT
For programming TEMPERATURE, FAN SPEED
and AIR FLOW DIRECTION, follow the procedure
shown below.
TEMPERATURE SETTING
A. UP AND DOWN DIRECTION
• The movable limit of the flap is changeable. Contact your Daikin dealer for details.
Press the AIR FLOW DIRECTION ADJUST
button to select the air direction as shown
below.
Press TEMPERATURE SETTING button and
program the setting temperature.
Each time this button is pressed, setting
temperature rises 1°C.
swing
The AIR FLOW FLAP display
swings as shown below and the
air flow direction continuously
varies. (Automatic swing setting)
Press AIR FLOW DIRECTION
ADJUST button to select the air
direction of your choice.
Each time this button is pressed, setting
temperature lowers 1°C.
• The setting is impossible for fan operation.
The AIR FLOW FLAP display
stops swinging and the air flow
direction is fixed (Fixed air flow
direction setting).
NOTE
• The setting temperature range of the remote controller is 16°C to 32°C.
FAN SPEED CONTROL
Press FAN SPEED CONTROL button.
High or Low fan speed can be selected.
The microchip may sometimes control the fan speed
in order to protect the unit.
AIR FLOW DIRECTION ADJUST
• There are 2 ways of adjusting the air discharge
angle.
1. A. Up and down adjustment
2. B. Left and right direction
Fig. 1
A. up and down direction
MOVEMENT OF THE AIR FLOW FLAP
For the following conditions, micro computer controls the air flow direction so it may be different from
the display.
Operation
mode
Operation
condition
Cooling
Heating
• When room
temperature is
lower than the
set temperature
• When room
temperature is
higher than the
set temperature
• At defrost operation
• When operating continuously at
horizontal air flow direction
Operation mode includes automatic operation.
B. LEFT AND RIGHT DIRECTION
Adjusting air flow direction in the left and right direction (Refer to Fig. 1)
B. Left and right direction
7
NOTE
• Only make adjustments after you have stopped
the air flow direction swing in a position where
adjustments are possible. Your hand may get
caught if you attempt to make adjustments while
the unit is swinging.
English
01_en_3P170549-4C.fm Page 8 Tuesday, November 6, 2007 9:36 AM
PROGRAM TIMER OPERATION
Operate in the following order.
• The timer is operated in the following two ways.
• Programming the stop time (
)
.... The system stops
operating after the set time has elapsed.
• Programming the start time (
)
.... The system starts
operating after the set time has elapsed.
• The timer can be programmed a maximum of 72 hours.
• The start and the stop time can be simultaneously
programmed.
1
TIMER MODE START/STOP
Press the TIMER MODE START/STOP button
several times and select the mode on the
display.
The display flashes.
For setting the timer stop .... “
For setting the timer start .... “
2
”
”
PROGRAMMING TIME
Press the PROGRAMMING TIME button and set
the time for stopping or starting the system.
When this button is pressed, the time
advances by 1 hour.
When this button is pressed, the time
goes backward by 1 hour.
3
TIMER ON/OFF
Press the TIMER ON/OFF button.
The timer setting procedure ends.
The display “
or
” changes from flashing light to a constant light.
Refer to figure 4 on page [1]
NOTE
• When setting the timer Off and On at the same
time, repeat the above procedure from 1 to 3
once again.
When the timer is programmed to stop the system
after 3 hours and start the system after 4 hours, the
system will stop after 3 hours and then 1 hour later
the system will start.
7. OPTIMUM OPERATION
Observe the following precautions to ensure the
system operates.
• Adjust the room temperature properly for a comfortable environment. Avoid excessive heating or
cooling.
• Prevent direct sunlight from entering a room during cooling operation by using curtains or blinds.
• Ventilate the room regularly.
Using the unit for long periods of time requires
attentive ventilation of the room.
• Keep doors and windows closed. If the doors and
windows remain open, room air will flow out and
cause to decrease the effect of cooling and heating.
• Do not place other heaters directly below the
indoor unit.
They may deform due to the heat.
• Never place objects near the air inlet and the air
outlet of the unit. It may cause deterioration in the
effect or stop in the operation.
• Turn off the main power supply switch when it is
not used for long periods of time. When the main
power switch is turned on, some watts of electricity
is being used even if the system is not operating.
Turn off the main power supply switch for saving
energy. When reoperating, turn on the main power
supply switch 6hours before operation for smooth
running (Refer to MAINTENANCE).
• When the display shows “
” (TIME TO CLEAN
AIR FILTER), ask a qualified service person to
clean the filters (Refer to MAINTENANCE).
• Fully use the function of air flow direction adjust.
Cold air gathers on the floor, and warm air gathers
in the ceiling.
Set the air flow direction parallel during cooling or
dry operation, and set it downwards during heating operation.
Do not let the air blow directly to a person.
• It takes time for the room temperature to reach the
set temperature.
We recommend starting the operation in advance
using timer operation.
• After the timer is programmed, the display shows
the remaining time.
• Press the TIMER ON/OFF button once again to
cancel programming. The display vanishes.
English
8
01_en_3P170549-4C.fm Page 9 Tuesday, November 6, 2007 9:36 AM
8. MAINTENANCE
(FOR SERVICE PERSONNEL)
ONLY A QUALIFIED SERVICE PERSON IS
ALLOWED TO PERFORM MAINTENANCE
IMPORTANT!
• BEFORE OBTAINING ACCESS TO TERMINAL
DEVICES, ALL POWER SUPPLY CIRCUITS
MUST BE INTERRUPTED
• To clean the air conditioner, be sure to stop operation, and turn the power switch off. Otherwise, an
electric shock and injury may result.
• Do not wash the air conditioner with water
Doing so may result in an electric shock.
• Be careful with a scaffold or staging
Caution must be exercised because of work at a
high place.
Fig. 2
HOW TO CLEAN THE AIR FILTER
Clean the air filter when the display shows “
”
(TIME TO CLEAN AIR FILTER).
It will display that it will operate for a set amount of
time.
Increase the frequency of cleaning if the unit is
installed in a room where the air is extremely contaminated.
If the dirt becomes impossible to clean, change the
air filter (Air filter for exchange is optional).
1. Open the suction grille.
Slide both knobs simultaneously as shown and
then pull them downward.
(Do the same procedure for closing.)
(Refer to Fig. 2)
2. Remove the air filters.
Push the 2 tabs up, and slowly lower the grille.
(Refer to Fig. 3)
3. Clean the air filter.
Use vacuum cleaner A) or wash the air filter with
water B).
A)Using a vacuum cleaner
B)Washing with water
When the air filter is very dirty, use soft brush
and neutral detergent.
Fig. 3
Remove water and dry in the shade.
tab
Fig. 4
Fig. 5
9
NOTE
• Do not wash the air conditioner with hot water of
more than 50°C, as doing so may result in discoloration and/or deformation.
• Do not expose it to fire, as doing so may result in
burning.
4. Fix the air filter.
Set the hatch of the air filter to the fook of the
suction grille, and fix the air filter.
(Refer to Fig. 5)
5. Close the suction grille.
Refer to item No. 1.
6. After turning on the power, press FILTER
SIGN RESET button.
The “TIME TO CLEAN AIR FILTER” display vanishes.
English
01_en_3P170549-4C.fm Page 10 Tuesday, November 6, 2007 9:36 AM
HOW TO CLEAN AIR OUTLET AND OUTSIDE
PANELS
• Clean with soft cloth.
• When it is difficult to remove stains, use water or
neutral detergent.
• When the flap is extremely contaminated, remove
it as below and clean or exchange it.
(Flap for exchange is optional)
NOTE
• Do not use gasoline, benzene, thinner, polishing
powder, liquid insecticide. It may cause discoloring or warping.
• Do not let the indoor unit get wet. It may cause an
electric shock or a fire.
• Do not scrub firmly when washing the blade with
water.
The surface sealing may peel off.
• Do not use water or air of 50°C or higher for cleaning air filters and outside panels.
HOW TO CLEAN THE SUCTION GRILLE
1. Open the suction grille.
Slide both knobs and then pull them downward.
(Do the same procedure for closing.)
2. Remove the air filter.
Refer to “HOW TO CLEAN THE AIR FILTER”.
(Refer to Fig. 2)
3. Remove the suction grille.
Open the suction grille and pull the knob on the
back of the suction grille forward. (Refer to Fig 4)
4. Clean the suction grille.
Wash with a soft bristle
brush and neutral detergent or water, and dry
throughly.
• When very grimy
Directly apply the type of detergent used for
cleaning ventilation fans or ovens, wait 10 minutes, and then rinse with water.
NOTE
• Do not wash the air conditioner with hot water of
more than 50°C, as doing so may result in discoloration and/or deformation.
5. Fix the air filter.
Refer to “HOW TO CLEAN THE AIR FILTER ”.
6. Fix the suction grille.
Refer to item No. 2.
7. Close the suction grille.
Refer to item No. 1.
START UP AFTER A LONG STOP
Confirm the following
• Check that the air inlet and outlet are not blocked.
Remove any obstacle.
English
• Check if the earth is connected.
Might there be a broken wire somewhere?
Contact your dealer if there are any problems.
Clean the air filter and outside panels
• After cleaning the air filter, make sure to attach it.
Turn on the main power supply switch
• The display on the remote controller will be shown
when the power is turned on.
• To protect the unit, turn on the main power switch
at least 6 hours before operation.
WHAT TO DO WHEN STOPPING THE SYSTEM FOR A LONG PERIOD
Turn on FAN OPERATION for a half day and dry
the unit.
• Refer to “FAN OPERATION”.
Cut off the power supply.
• When the main power switch is turned on, some
watts of electricity is being used even if the system is not operating.
Turn off the main power supply switch for saving
energy.
• The display on the remote controller will vanish
when the main power switch is turned off.
Clean the air filter and the exterior.
• Be sure to replace the air filter to its original place
after cleaning. Refer to “MAINTENANCE”.
9. NOT MALFUNCTION OF THE AIR
CONDITIONER
The following symptoms do not indicate air conditioner malfunction
I. THE SYSTEM DOES NOT OPERATE
• The system does not restart immediately after
the ON/OFF button is pressed.
If the OPERATION lamp lights, the system is in
normal condition.
It does not restart immediately because a safety
device operates to prevent overload of the system. After 3 minutes, the system will turn on again
automatically.
• The system does not restart immediately when
TEMPERATURE SETTING button is returned to
the former position after pushing the button.
If the OPERATION lamp lights, the system is in
normal condition.
It does not restart immediately because a safety
device operates to prevent overload of the system. After 3 minutes, the system will turn on again
automatically.
10
01_en_3P170549-4C.fm Page 11 Tuesday, November 6, 2007 9:36 AM
• The system does not start when the display
shows “
” (UNDER CENTRALIZED
CONTROL) and it flashes for few seconds
after pressing an operation button.
This is because the system is under centralized control. Flashes on the display indicates that the system
cannot be controlled by the remote controller.
• The system does not start immediately after
the power supply is turned on.
Wait one minute until the micro computer is prepared for operation.
II. WHITE MIST COMES OUT OF A UNIT
• When humidity is high during cooling operation
(In oily or dusty places)
If the inside of an indoor unit is extremely contaminated, the temperature distribution inside a room
becomes uneven. It is necessary to clean the
inside of the indoor unit. Ask your Daikin dealer for
details on cleaning the unit. This operation
requires a qualified service person.
• When the system is changed over to HEATING
OPERATION after DEFROST OPERATION.
Moisture generated by DEFROST becomes
steam and exists.
III.NOISE OF AIR CONDITIONERS
• A ringing sound after the unit is started.
This sound is generated by the temperature regulator working.
It will quiet down after about a minute.
• A continuous flow “Shuh” sound is heard
when the systems is in COOLING or DEFROST
OPERATION.
This is the sound of refrigerant gas flowing
through both indoor and outdoor units.
• A “Shuh” sound which is heard at the start or
immediately after the stop of operation or
which is heard at the start or immediately after
the stop of DEFROST OPERATION.
This is the noise of refrigerant caused by flow stop
and flow change.
• A continuous low “Shah” sound is heard when the
system is in COOLING OPERATION or at a stop.
The noise is heard when the drain pump is in
operation.
• A “Pishi-pishi” squeaking sound is heard
when the system is in operation or after the
stop of operation.
Expansion and contraction of plastic parts caused
by temperature change makes this noise.
IV.DUST FROM THE UNITS
• Dust may blow out from the unit after starting
operation from long resting time.
Dust absorbed by the unit blows out.
11
V. THE UNITS GIVE OFF ODORS
The unit absorbs the smell of rooms, furniture,
cigarettes, etc., and then emits them.
VI.THE LIQUID CRYSTAL OF THE REMOTE CONTROLLER SHOW “
”
• It happens immediately after the main power
supply switch is turned on.
This shows that the remote controller is in normal
condition.
This continues temporary.
10. TROUBLE SHOOTING
I. If one of the following malfunctions occurs,
take the measures shown below and contact
your Daikin dealer.
The system must be repaired by a qualified service
person.
WARNING
When the air conditioner is in abnormal conditions (smell of something burning, etc),
unplug the power cord from the outlet, and
contact your dealer
Continued operation under such circumstances
may result in a failure, electric shock, and fire.
• If a safety device such as a fuse, a breaker or an
earth leakage breaker frequently actuates;
Measure: Do not turn on the main power switch.
• If the ON/OFF switch does not properly work;
Measure: Turn off the main power switch.
• If water leaks from unit.
Measure: Stop the operation.
• If the display “
” (INSPECTION), “UNIT No.”,
and the OPERATION lamp flash and the “MALFUNCTION CODE” appears.
OPERATION lamp
UNIT No.
C
INSPECTION
display
L H
INDOOR UNIT
No. in which a
malfunction occurs
MALFUNCTION CODE
Measure: Notify your Daikin dealer and inform
him/her of the display.
English
01_en_3P170549-4C.fm Page 12 Tuesday, November 6, 2007 9:36 AM
II. If the system does not properly operate except
for the above mentioned case, and none of the
above mentioned malfunctions is evident,
investigate the system according to the following procedures.
• If the heat source of the room is excessive
(when cooling).
Cooling effect decreases if heat gain of the
room is too large.
1. If the system does not operate at all.
• Check if there is a power failure.
Wait until power is restored. If power failure
occurs during operation, the system automatically restarts immediately after the power supply recovers.
• Check if no fuse has blown.
Turn off the power supply.
• Check if the breaker is
ON
Switch
blown.
Turn the power on with
Trip position
the breaker switch in
Breaker
OFF
the off position.
Do not turn the power on with the breaker
switch in the trip position.
(Contact your dealer.)
2. If the system stops operating after operating
the system.
• Check if the air inlet or outlet of outdoor or
indoor unit is blocked by obstacles.
Remove the obstacle and make it well-ventilated.
• Check if the air filter is clogged.
Ask a qualified service person to clean the air
filters (Refer to MAINTENANCE).
3. The system operates but it does not sufficiently cool or heat.
• If the air inlet or outlet of the indoor or the outdoor unit is blocked with obstacles.
Remove the obstacle and make it well-ventilated.
• If the air filter is clogged.
Ask a qualified service person to clean the air
filters (Refer to MAINTENANCE).
• If the set temperature is not proper (Refer to
ADJUSTMENT).
• If the FAN SPEED button is set to LOW SPEED
(Refer to ADJUSTMENT).
• If the air flow angle is not proper (Refer to
ADJUSTING THE AIR FLOW DIRECTION).
• If the doors or the windows are open.
Shut doors or windows to prevent wind from
coming in.
• If direct sunlight enters the room (when cooling).
Use curtains or blinds.
• When there are too many inhabitants in the
room (when cooling).
Cooling effect decreases if heat gain of the
room is too large.
English
12
13
POWER INPUT RATING
CURRENT INPUT RATING
CAPACITY
POWER INPUT RATING
CURRENT INPUT RATING
CAPACITY
MANUFACTURER’S NAME
COUNTRY OF ORIGIN
WEIGHT OF INDOOR UNIT
WEIGHT OF OUTDOOR UNIT
REFRIGERANT
MASS OF REFRIGERANT CHARGE
HEATING
INDOOR UNIT
OUTDOOR UNIT
RATED VOLTAGE
RATED FREQUENCY
COOLING
POWER INPUT RATING
CURRENT INPUT RATING
CAPACITY
NET WEIGHT OF INDOOR UNIT
NET WEIGHT OF OUTDOOR UNIT
REFRIGERANT
MASS OF REFRIGERANT CHARGE
HEATING
INDOOR UNIT
OUTDOOR UNIT
RATED VOLTAGE
RATED FREQUENCY
COOLING
POWER INPUT RATING
CURRENT INPUT RATING
CAPACITY
THAILAND
THAILAND
outdoor DAIKIN INDUSTRIES DAIKIN INDUSTRIES DAIKIN INDUSTRIES DAIKIN INDUSTRIES DAIKIN INDUSTRIES
(THAILAND)LTD. (THAILAND)LTD. (THAILAND)LTD. (THAILAND)LTD. (THAILAND)LTD.
indoor DAIKIN INDUSTRIES DAIKIN INDUSTRIES DAIKIN INDUSTRIES DAIKIN INDUSTRIES DAIKIN INDUSTRIES
(THAILAND)LTD. (THAILAND)LTD. (THAILAND)LTD. (THAILAND)LTD. (THAILAND)LTD.
THAILAND
THAILAND
indoor
outdoo
kg
THAILAND
THAILAND
THAILAND
THAILAND
V
Hz
kW
A
kW
kcal/h
kW
A
kW
kcal/h
kg
kg
THAILAND
THAILAND
FHY125BVE
RY125FUTAL
220
60
6.6
18.1
12.5
10800
5.42
14.9
15.0
12900
35
115
R22
3.1
FHY100BVE
RY100FUVAL
220
60
5.9
27.6
9.0
7700
5.0
23.5
11.8
10100
32
120
R22
2.6
FHY71BVE
RY71FUVAL
220
60
4.3
20.3
6.7
5800
3.8
18.0
8.5
7300
27
91
R22
2.3
FHY60BVE
RY60GVAL
220
60
3.06
14.8
5.6
4820
2.44
11.8
7.1
6110
27
62
R22
1.75
kg
FHY50BVE
RY50GVAL
220
60
2.34
11.4
5.0
4300
1.85
9.0
6.05
5200
24
50
R22
1.45
V
Hz
kW
A
kW
kcal/h
kW
A
kW
kcal/h
kg
kg
FH125BVE
R125FUTAL
220
60
7.0
19.1
12.5
10800
35
110
R22
3.1
FH100BVE
R100FUVAL
220
60
5.8
27.4
9.0
7700
32
117
R22
2.9
FH71BVE
R71FUVAL
220
60
4.2
20.0
6.7
5800
27
87
R22
2.2
FH60BVE
R60GVAL
220
60
3.2
15.2
5.6
4800
27
51
R22
1.60
FH50BVE
R50GVAL
220
60
2.5
11.8
4.5
3900
24
41
R22
1.15
01_en_3P170549-4C.fm Page 13 Tuesday, November 6, 2007 9:36 AM
11. SPECIFICATIONS
(These specifications are in compliance with SASO386.)
English
00_CV_3P170549-4C.fm Page 4 Tuesday, November 6, 2007 9:30 AM
3P170549-4C EM00A035B
(0712) HT
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising