Barco | MD-4221 | User manual | Barco MD-4221 User manual

Barco MD-4221 User manual
MD-4221
42” HD MEDICAL LCD MONITOR
User manual
2
Copyright notice
This document is copyrighted. All rights are reserved. Nor this document, nor any part
of it, may be reproduced or copied in any form or by any means - graphical, electronic, or
mechanical including photocopying, taping or information storage and retrieval systems without written permission of Barco
© 2008 Barco N.V. All rights reserved.
제 품 명
모 델 명
정격입력
제 조 자
DnT-MD-4221(B) 제조국가
: 42” LCD 모니터
: MD-4221
: 100-230V~ 50-60Hz, 3A MAX
: ㈜디앤티
: 대한민국
3
Table of Contents
Table of Contents ....................................................................................... 4
Preface........................................................................................................ 5
Important notice.................................................................................... 5
Environmental information................................................................... 5
Safety Instructions ................................................................................... 6
On Safety ............................................................................................... 6
Caution................................................................................................... 8
FCC Information ................................................................................... 11
Electromagnetic compatibility ............................................................ 13
Recommendations for using your display system............................. 14
Unpacking and handling tips .............................................................. 14
Preventing fire and injury................................................................... 15
Explanation of symbols....................................................................... 15
Introduction.............................................................................................. 17
Quick Startup ....................................................................................... 17
Package Overview............................................................................... 17
Connectors ........................................................................................... 18
Mechanical product drawing .............................................................. 20
Controls................................................................................................ 21
Power management ........................................................................... 23
On-Screen Display Menus ........................................................................ 24
OSD functions description........................................................................ 29
Standard signal table ............................................................................... 34
PC modes supported ........................................................................... 34
SDI video format ................................................................................. 35
Signal connector pin assignments .......................................................... 36
Specifications ........................................................................................... 40
BARCO MID GENERAL WARRANTY TERMS AND CONDITIONS ................... 41
4
Preface
Important notice
Notice
Although every attempt has been made to achieve technical accuracy in this document,
we assume no responsibility for errors that may be found. Our goal is to provide you with
the most accurate and usable documentation possible; if you discover errors, please let
us know.
Barco software products are the property of Barco. They are distributed under copyright
by Barco N.V., for use only under the specific terms of a software license agreement
between Barco N.V. and the licensee. No other use, duplication, or disclosure of a Barco
software product, in any form, is authorized.
The specifications of Barco products are subject to change without notice.
Trademarks
All trademarks and registered trademarks are property of their respective owners.
Environmental information
Disposal Information
The lamps inside the display contain mercury. Do not throw the display in the trash.
Dispose of it as required by local ordinances or regulations.
This equipment has required the extraction and use of natural resources for its production.
It may contain hazardous substances for health and environment.
In order to avoid the dissemination of those substances in the environment and to
diminish the pressure on natural resources, we encourage you to use the appropriate
take-back systems.
Those systems will reuse or recycle most of the materials of your end-of-life equipment
in a sound way.
The crossed-out wheeled bin symbol invites you to use those systems.
If you need more information on the collection, reuse and recycling systems,
please contact your local or regional waste administrator.
You can also contact us for more information on the environmental performances of our
products.
5
Safety Instructions
On Safety
1.
Before connecting the AC power cord to the DC adapter outlet make sure the
voltage designation of the DC adapter corresponds to the local electrical
supply.
2.
Never insert anything metallic into the cabinet openings of the Liquid Crystal
Display (LCD) monitor. Doing so may create the danger of electric shock.
3.
To reduce the risk of electric shock, do not remove cover.
No user-serviceable parts inside. Only a qualified technician should open the
case of the LCD monitor.
4.
Never use your LCD monitor if the power cord has been damaged.
Do not allow anything to rest on the power cord, and keep the cord away
from areas where people can trip over it.
5.
Be sure to hold the plug, not the cord, when disconnecting the LCD monitor
from an electric socket.
6.
Unplug your LCD monitor when it is going to be left unused for an extended
period of time.
7.
Unplug your LCD monitor from the AC outlet before any service.
8.
If your LCD monitor does not operate normally-in particular, if there are any
unusual sounds or smells coming from it, unplug it immediately and contact
an authorized dealer or service center.
Warning
Do not to touch signal input, signal output or other connectors, and the patient
simultaneously.
Warning
External equipment intended for connection to signal input, signal output or other
connectors, shall comply with relevant IEC standard (e.g.,IEC60950 for IT equipment and
IEC60601 series for medical electrical equipment).
In addition, all such combinations (systems) shall comply with the standard IEC
60601-1-1, safety requirements for medical electrical systems. Any person who connects
has formed at system and is therefore responsible for the system to comply with the
requirements of IEC 60601-1-1.
If in doubt, contact a qualified technician or your local sales representative.
6
Warning
When necessary, carry this product with at least 2 persons, using both handles on left
and right side of the product. If you want the product to be installed on another place,
please contact Barco Customer Service center.
On installation
1.
Openings in the LCD monitor cabinet are provided for ventilation.
To prevent overheating, these openings should not be blocked or covered. If
you put the LCD monitor in a bookcase or some other enclosed space, be sure
to provide adequate ventilation.
2.
Put your LCD monitor in a location with low humidity and minimal dust.
3.
Do not expose the LCD monitor to rain or use it near water (in kitchens, near
swimming pools, etc.). If the LCD monitor accidentally gets wet, unplug it and
contact an authorized dealer immediately. You can clean the LCD monitor with
a damp cloth if necessary, but be sure to unplug the LCD monitor first.
4.
Locate your LCD monitor near an easily accessible AC outlet.
5.
High temperature can cause problems. Don't use your LCD monitor in direct
sunlight and keep it away from heaters, stoves, fireplaces, and sources of
heat.
Environmental Conditions for transport and Storage
•
Temperature range within -20°C to 60°C
•
Relative humidity range 10% to 85%
•
Atmospheric pressure range within 500 to 1060hPa.
Rapid change in ambient temperature may adversely affect the product.
Allow about 8 hours for the product to reach an ambient temperature for starting
use.
Intended Use
This TFT-LCD Monitor is as accessory intended for use with Medical Equipment to display
alpha, numerical and graphical data.
7
Caution
To prevent fire or shock hazards, do not expose this unit to rain or moisture. Also, do not
use this unit's polarized plug with an extension cord receptacle or other outlets unless
the prongs can be fully inserted.
The display is designed to meet the medical safety requirements for patient vicinity
device.
This device may not be used in connection with life support equipment.
This symbol alerts the user that important literature concerning the
operation of this unit has been included. Therefore, it should be read
carefully in order to avoid potential problems.
This symbol warns user that un-insulated voltage within the unit may
have sufficient magnitude to cause electrical shock. Therefore, it is
dangerous to make contact with any part inside the unit. To reduce the
risk of electric shock, DO NOT remove cover (or back).
There are no user serviceable parts inside. Refer servicing to qualified
service personal.
Underwriters Laboratories (UL) Classification:
UL safety Compliance:
This LCD monitor is U.L. Classified WITH RESPECT TO ELECTRIC SHOCK, FIRE
AND MECHANICAL HAZARDS ONLY IN ACCORDANCE WITH
UL 60601-1/CAN/CSA C22.2 NO. 601.1
EEC Safety Compliance:
This display unit meets the requirements of EN-60601-1 so as to conform
to the Medical Device Directive 93/42/EEC (general safety information).
Using Plug for US: 120V rating 5-15P type only.
Caution: Make sure the power cord is the correct type that is required in your area.
This LCD monitor has a universal power supply that allows operation in either 100-120V
AC or 200-240V AC voltage areas (no user adjustment is required).
8
Use the proper power cord with correct attachment plug type. If the power source is
120V AC, use a power cord which is a Hospital Grade Power Cord with NEMA 5-15 style
plug, labeled for 125 volts AC with UL and C-UL approvals. If the power source is a 240 V
AC supply, use the tandem (T blade) type attachment plug with ground conductor power
cord that meets the respective European country's safety regulations.
The hospital-grade plug for medical products intended for use in Denmark has DEMKO
approval and is rated 13 amps at 250Vac. Plug is recommended for use in medical
applications and specifications are being added to the standard S B 107-2-D1. Plug mates
with maker's Danish hospital-grade socket. Hospital sockets have slightly different
shaped openings allowing only the hospital plug, not the standard Danish plug, to be
inserted, to protect the ac circuit in specific medical settings.
Cleaning Instructions
Follow your hospital protocol for the handling of blood and body fluids.
Clean the display with a diluted mixture of mild detergent and water. Use
a soft towel or swab.
Use of certain cleaning agents may cause degradation to the labels and
plastic components of the product.
Consult cleanser manufacturer to see if agent is compatible with it. Do not
allow liquid enter the display.
Maintenance
Replacing the Fuses:
To avoid the risk of fire, use only fuses of the value specified on the fuse
label located on the rear panel.
•
Unplug the power cord from the wall outlet.
•
Unlatch the fuse holder above the AC inlet and remove it. (You may need to
press the tab on the fuse holder with a slender screwdriver to release the latch)
•
Replace the fuse with the same value and rating.
•
Reinstall the fuse holder until the tab snaps in place.
9
Servicing
Do not attempt to service the apparatus yourself as opening or removing covers may
expose you to dangerous voltages or other hazards, and will void the warranty.
Refer all servicing to qualified service personnel.
Unplug the apparatus from its power source and refer servicing to qualified personnel
under the following conditions:
•
If the power cord or plug is damaged or frayed.
•
If liquid has been spilled into the apparatus.
•
If objects have fallen into the apparatus.
•
If the apparatus has been exposed to rain or moisture.
•
If the apparatus has been subjected to excessive shock by being dropped.
•
If the cabinet has been damaged.
•
If the apparatus seems to be overheated.
•
If the apparatus emits smoke or abnormal odor.
•
If the apparatus fails to operate in accordance with the operating instructions.
Accessories
Use only accessories specified by the manufacturer, or sold with the apparatus.
Classification
.
10
•
Protection against electric shock : Class I
•
Applied Parts : No Applied Parts
•
Protection against harmful ingress of water : IPX1
•
Degree of safety in the presence of flammable anesthetics mixture with air or
with oxygen or with nitrous oxide:
Not suitable for use in the presence of a flammable anesthetics mixture with
oxygen or with nitrous oxide.
•
Mode of operation: Continuous.
FCC Information
This equipment has been tested and found to comply with the limits of a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against interference. This
monitor can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, it may interfere with other radio communications equipment. There
is no guarantee that interference will not occur in a particular installation.
If this equipment is found to cause harmful interference to radio or television reception,
the user is encouraged to try to correct the interference by carrying out one or more of
the following measures:
1.
Reorient or relocate the receiving antenna.
2.
Increase the distance between the color monitor and the subject of
interference.
3.
Plug the monitor into an outlet on a different electrical circuit than the one to
which the subject of interference is connected.
4.
Consult the dealer or an experienced radio/TV technician for help.
NOTICES TO THE USER:
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC WARNING:
This equipment generates or uses radio frequency energy. Changes or modifications to
this equipment may cause harmful interference unless the modifications are expressly
approved in the instruction manual. The user could lose authority to operate this
equipment if an unauthorized change or modification is made.
1. Guidance and manufacturer's declaration - electromagnetic emissions
The MD-4221 is intended for use in the electromagnetic environment specified below.
The customer or the user of the MD-4221 should assure that it is used in such an
environment.
Emission test
Compliance
Electromagnetic
environment -guidance
RF Emissions
CISPR 11
Group 1
MD-4221 is suitable for use
in all establishments,
11
RF Emissions
CISPR 11
Class B
Harmonic emissions
IEC 61000-3-2
D
Voltage fluctuations
IEC 61000-3-3
Complies
including domestic
establishments and those
directly connected to the
public low-voltage power
supply network that
supplies buildings used for
domestic purposes
2. Guidance and manufacturer's declaration - electromagnetic immunity
The MD-4221 is intended for use in the electromagnetic environment specified below.
The customer or the user of the MD-4221 should assure that it is used in such an
environment.
Immunity test
IEC 60601 Test level
Compliance
Electromagnetic
environment
-guidance
Electrostatic
discharge(ESD)
6kV Contact
6kV Contact
8kV air
8kV air
Floors should be
wood, concrete or
ceramic tile. If
floors are covered
with synthetic
material, the
relative humidity
should be at least
30%
Electrical fast
transient/burst
2kV for power
supply lines
2kV for power
supply lines
IEC 61000-4-4
1kV for
input/output lines
1kV for
input/output lines
Harmonic emissions
IEC 61000-3-2
D
Voltage fluctuations
IEC 61000-3-3
Complies
IEC61000-4-2
12
Mains power
quality should be
that of a typical
commercial or
hospital
environment
Electromagnetic compatibility
Warning
When this device is connected with other electrical equipment, leakage
currents may be additive. To minimize total leakage current per patient,
ensure that all systems are installed according to the requirements of IEC
60601-1-1.
Caution
Portable and mobile RF communications equipment may affect the normal function of
the display. Do not use cables or accessories other than those provided with the display,
as this may result in increased electromagnetic emissions or decreased immunity to such
emissions. If the display is used adjacent to other equipment, observe and verify normal
operation of the display in the configuration in which it will be used prior to using it in a
surgical procedure. Consult the tables below for guidance in placing the display.
Like other electrical medical equipment, the MD-4221 requires special precautions to
ensure electromagnetic compatibility with other electrical medical devices. To ensure
electromagnetic compatibility (EMC), the display must be installed and operated
according to the EMC information provided in this manual. The display have been
designed and tested to comply with IEC 60601-1-2:2001 requirements for EMC with other
devices.
13
Recommendations for using your display system
1. Optimize the lifetime of your display
Enabling the Display Power Management System (DPMS) of your display (in the display’s
Settings menu) will optimize LCD backlight lifetime by automatically switching off the
backlight when the display is not used for a specified period of time. By default, DPMS is
enabled on your display, but it also needs to be activated on your workstation. To do this,
go to “Power Options Properties” in the “Control Panel”.
Barco recommends setting DPMS activation after 20 minutes of non-usage.
2. Use a screen saver to avoid image retention
Prolonged operation of an LCD with the same content on the same screen area may
result in a form of image retention.
You can avoid or significantly reduce the occurrence of this phenomenon by using a
screen saver. You can activate a screen saver in the “Display properties” window of your
workstation.
Barco recommends setting screen saver activation after 5 minutes of non-usage. A good
screen saver displays moving content.
In case you are working with the same image or an application with static image
elements for several hours continuously (so that the screen saver is not activated),
change the image content regularly to avoid image retention of the static elements.
3. Understand pixel technology
LCD displays use technology based on pixels. As a normal tolerance in the manufacturing
of the LCD, a limited number of these pixels may remain either dark or permanently lit,
without affecting the diagnostic performance of the product. To ensure optimal product
quality, Barco applies strict selection criteria for its LCD panels.
To learn more about LCD technology and missing pixels, consult the dedicated white
paper available at www.barcomedical.com.
Unpacking and handling tips
The display is a precision instrument that requires proper care to maintain product
operation and adherence to specification. Unpack the display and components carefully,
then set up and handle the unit properly to avoid damage to the LCD panel.
14
•
Always lift and carry the display with 2 persons.
•
Use both hands to grasp the display case when lifting it from the shipping
carton, but avoid touching the screen.
•
Do not apply pressure to the screen or touch the screen with bare fingers or
objects. Pressure can affect image quality. Cosmetics and oils on the skin are
both detrimental to the screen and difficult to remove.
•
Allow the display to warm up to room temperature before turning it on. Avoid
sudden temperature changes in the environment, as this may cause
condensation, which damages the display.
•
Do not set up the display near strong light or heat sources.
•
Do not block the vents on the back of the display or install the display in a
built-in enclosure. Blocked vents cause excessive heat to build up inside the
display, increasing risk of fire.
•
When installing components, turn off your computer, but leave it plugged into a
grounded outlet.
•
Do not remove the back cover or disassemble the display. There are no
user-serviceable parts inside.
Preventing fire and injury
•
Replace the power supply cables if damaged.
•
Use only the power source indicated in this guide or listed on the display.
•
Do not plug the power supply into an overloaded AC outlet or extension cord.
Overloaded AC outlets and cords can result in electric shock or fire.
•
Do not drop or push objects into the display case. Internal components contain
high voltage.
•
Unplug the power cord from the wall outlet during thunderstorms.
•
Do not place magnetic devices, such as motors, near the display.
Explanation of symbols
Dangerous : High Voltage.
Consult accompanying documents.
Direct Current.
lndicates protective earth ground.
DC Power control switch.
15
Serial Number.
Top-Bottom.
Fragile.
Do not get wet.
Maximum Stacking.
Indicates proof of conformity to applicable European Economic
Community Council directives and to harmonized standards
published in the official journal of the European Communities.
Medical Equipment is in accordance with UL 60601-1 and
CAN/CSA C22.2 No.601.1 in regards to electric shock, fire hazards,
and mechanical hazards.
Tested to comply with FCC Class B standards.
This symbol indicates that the waste of electronic equipment must
not be disposed as unsorted municipal waste and must be
collected separately. Please contact the manufacturer or other
authorized disposal company to decommission your equipment.
Tested to comply with VCCI Class B standards.
Indicates that the device is protected against the effects of
vertically falling water.
16
Introduction
Quick Startup
1. Connect the power supply to the display via the power plug.
2. Plug into the AC inlet with power cord cable.
3. Connect the video source to this monitor.
4. Apply power to the peripheral device.
5. Turn on the switch of this monitor.
Package Overview
The package contains the 42-inch display and the following accessories:
User manual
User Manual (CD)
AC power cord
(220V)
AC power cord
(110V)
DVI cable
VGA cable
Remote control
17
Connectors
18
19
Mechanical product drawing
20
Controls
Remote control
Key
F1
Description
Input Selection, same as input button on user controls
F2
PiP Button on OSD
F3
PiP Swap
F4
No Function
F5
Shows RS232 address
UP
Move in OSD same as up key on user controls
DOWN
LEFT
RIGHT
Move in OSD same as down key on user controls
Adjust in OSD, same as - key
Adjust and enter adjust in OSD, same as + key
ADJ
Enter OSD, same as menu button on user controls
EXIT
Exits OSD, same as menu button on user controls
ENTER
Standby
PAUSE
||
TEXT
?
Enter OSD submenu, same as menu button on user
contols
Turns the display off and on, same as standby key
on user controls
Change baud rate of RS232
Freeze frame
Switch on/off 4:3 mode
Help, show firmware version - same as with service
menu
PHASE UP
Adjust frequency up
PHASE DN
Adjust frequency down
SHARPN UP Adjust sharpness up
SHARPN DN Adjust sharpness down
TINT UP
Adjust hue up
TINT DN
Adjust hue down
COLOR UP
Adjust saturation up
COLOR DN
Adjust saturation down
BRIGHTN UP Adjust brightness up
BRIGHTN DN Adjust brightness down
CONTR UP
Adjust contrast up
CONTR DN
Adjust contrast down
21
OSD buttons position
OSD Button Function
An 8-button keypad, located on the right hand side of the display, allows the user to
make adjustments to various display parameters using the On Screen Display (OSD)
system.
22
● Power LED
Green : Normal mode
Amber: Standby mode
Amber: Soft power-off
● On-Screen Display (OSD) Function Button
1. POWER : Turns ON/OFF the monitor.
2. MENU :
With OSD deactivated, Activate the OSD menu.
With OSD activated, Exit from main menu
or sub menu.
3. PIP :
With OSD deactivated, Hot key of PIP mode.
4. UP :
With OSD deactivated, Hot key of the brightness control and increases
the brightness.
With OSD activated, move the cursor upward.
5. DOWN :
With OSD deactivated, Hot key of the brightness control and decreases
the brightness.
With OSD activated, move the cursor downward.
6. MINUS :
With OSD deactivated, Hot key of the contrast control and decreases
the contrast.
With OSD activated, decreases the adjustment of the selected
function.
7. PLUS :
With OSD deactivated, Hot key of the contrast control and increase the
contrast.
With OSD activated, enter sub menu and increases the adjustment of
the selected function.
8. INPUT :
Change the display signal source. If VGA Analog's picture size not
matched with full screen size or image is noisy press the input button
during 2~3 seconds then you can see the most appropriate screen.
Power management
This monitor does not adhere to the VESA DPMS standard when no signal is present on
the video inputs.
Status
LED sign
Power Consumption
Normal Mode
Green on
<260W
Standby Mode
Amber
<17W
Soft power-off
Amber
<14W
23
On-Screen Display Menus
Adjust
<VGA Analog/RGBS input>
<DVI input>
<YPbPr input>
24
<SDI input>
<SVideo/CVideo input>
BRIGHTNESS
Increase or decrease the brightness. (Range : 0~100)
CONTRAST
Increase or decrease the Contrast. (Range : 0~100)
SHARPNESS (1)
Adjusts the sharpness of video image. (Range : 0~100)
SHARPNESS (2)
Adjusts the sharpness of video image. (SOFTEST, SOFT, NORMAL,
SHARP, SHARPEST)
COLOR (3)
Changes the color value. (Range : 0~100)
HUE (3)
Changes the Hue. (Range : 0~100)
BACKLIGHT
Adjusts backlight dimming level. (Range : 0~100)
PHASE (4)
Adjust backlight dimming level. (Range : 0~100)
FREQUENCY (4)
Increase or decrease the sampling frequency. (Range : 0~100)
AUTO ADJUST (5)
Fit to the most appropriate screen on the VGA Analog signal
(1): Available only for YPbPr, SVideo/CVideo input sources
(2): Available only for VGA Analog/RGBS and DVI input sources
(3): Not available for VGA Analog/RGBS and DVI input sources
(4): Not available for DVI, SVideo/Cvideo and SDI input sources
(5): Available only for VGA Analog/RGBS input sources
Color temp
MODE
Change the color model. (6500K,Full white,Clearbase, USER)
RED
Red balance (Only Working with USER mode) (Range : 0~100)
GREEN
Green balance (Only Working with USER mode) (Range : 0~100)
BLUE
Blue balance (Only Working with USER mode) (Range : 0~100)
25
Advanced
<DVI and SDI inputs>
SCALING
<Other inputs>
Change the image size
(Best Fit, Fit Width, Fit Height,Native,Full Display)
H POSITION (6)
Adjust the horizontal position of the displayed source
image.(Range : 0~100)
V POSITION (6)
Adjust the vertical position of the displayed source image.
(Range : 0~100)
POWER SAVE
On/Off the power save function
DISPLAY FUNCTION
Adjust GAMMA value.
(NATIVE,GAMMA1.8,GAMMA2.0,GAMMA2.2,GAMMA2.4,
GAMMA2.6,DICOM,VIDEO)
OVER SCAN
Adjust the displayed size. (0~8)
IMAGE SETTING
Change the image setting (Mode 1,2,3,4,5) for different
ambient light environments.
ZOOM / PAN
Enlarge the image and pan the screen.
FREEZE FRAME
Keep still the image
(6): Not available for DVI and SDI input sources
26
Setup
LANGUAGE
Change the OSD language. (8 languages)
BACKGROUND
Set the Background color
RS-232 BAUDRATE
Change RS232 BAUDRATE (115200,38400,19200,9600)
RS-232 ADDRESS
Set the RS232 Address.(Range : 1~255)
OSD COLOR
Adjust the OSD background from white opaque to half
translucent.
OSD POSITION
Change the OSD position
OSD TIMEOUT
Adjust time until the OSD Menu will disappear after adjusting
the menu. (5, 10, 20, 30, 60, 90, 120, 180, 240 seconds)
RESTORE SETTINGS
Changes the all OSD value to factory outgoing status.
AUTO SOURCE
SELECT
Enable or disable auto source select.
USER NAME ENTRY
Register user name. It appears on LOGO when powered on.
27
PIP
LAYOUT
Change the OSD layout. (Single, PIP, PBP1, PBP2)
SOURCE 1
Change the primary source.
SOURCE 2
Change the secondary source.
SIZE
Adjust PIP size. (Small,Large)
POSITION
Change the PIP position. (9 positions)
TOGGLE
Swaps the position of the Primary and Secondary images.
28
OSD functions description
Menus
Function Descriptions
BRIGHTNESS
Setting the brightness too high or too low will decrease
the amount of visible information.
CONTRAST
Setting the Contrast too high or too low will cause loss
of some grayscales.
FREQUENCY
Do not adjust freely. It will adjust fine state
automatically after auto adjustment.
When frequency value is wrong, the image has the
wrong horizontal size or contains noise.
PHASE
Do not adjust freely. It will adjust fine state
automatically after auto adjustment.
BACKLIGHT
Setting the backlight too low will cause dark image and
too high will decrease the backlight lifetime.
AUTO ADJUST
Automatically adjusts analog video signals.
SHARPNESS
Adjusts the sharpness of video image.
COLOR
Change the saturation of color.
HUE
Change the Hue.
COLOR TEMP 6500K
Color temperature selection (Full white, 6500K,
Clearbase, User)
Scaling
Native or scaling of image to Best Fit, Fit Width, Fit
Height, or Full Display.
‘Best Fit’, ‘Fit width’, ‘Fit height’ do not affect the
aspect ratio.
29
30
31
32
33
Standard signal table
PC modes supported
Horizontal Frequency (KHz)
Vertical Frequency
(Hz)
Clock Frequency
(MHz)
640 X 350 @70Hz
31.469
70.087
25.175
720 X 400 @70Hz
31.469
70.082
28.324
640 X 480 @60Hz
31.469
59.940
25.175
640 X 480 @75Hz
37.500
75.000
31.500
800 X 600 @60Hz
37.879
60.317
40.000
800 X 600 @75Hz
46.875
75.000
49.500
1024 X 768 @60Hz
48.363
60.004
65.000
1024 X 768 @75Hz
60.023
75.029
78.750
1152 X 864 @60Hz
54.348
60.053
80.000
1152 X 864 @75Hz
67.500
75.000
108.000
1280 X 1024@75Hz
79.976
75.025
135.000
1600 X 1200@60Hz
74.077
59.981
130.375
1920 X 1080@60Hz
67.500
60.000
148.500
Resolution
34
SDI video format
Output Signal
Description
SMPTE-274M
1080i (60 / 59.94 / 50) 1080p (30 /29.97 / 25 / 24
/ 24sF / 23.98 / 23.98sF)
SMPTE-296M
720p (60 / 59.94 / 50)
SMPTE-260M
1035i (60 / 59.94)
SMPTE-125M
480i (59.94)
ITU-R BT.656
576i (50)
35
Signal connector pin assignments
VGA (15-pin D-sub)
Pin No.
Assignment
Pin No.
Assignment
1
Red
9
No Connection
2
Green
10
Ground-Sync
3
Blue
11
Ground
4
Ground
12
DDC Data
5
DDC 5V Standby
13
H.Sync
Cable Connection check
14
V.Sync
6
Ground-Red
15
DDC Clock
7
Ground-Green
8
Ground-Blue
DVI in-out (24-pin DVI-D)
Pin No.
Assignment
Pin No.
Assignment
1
T.M.D.S. Data2-
13
No Connection
2
T.M.D.S. Data2+
14
+5V Power
3
T.M.D.S. Data2 Shield
15
Cable Connection check
4
No Connection
16
Hot Plug Detect
5
No Connection
17
T.M.D.S. Data0-
6
DDC Clock
18
T.M.D.S. Data0+
36
7
DDC Data
19
T.M.D.S. Data0 Shield
8
No Connection
20
No Connection
9
T.M.D.S. Data1-
21
No Connection
10
T.M.D.S. Data1+
22
T.M.D.S. Clock Shield
11
T.M.D.S. Data1 Shield
23
T.M.D.S. Clock+
12
No Connection
24
T.M.D.S. Clock-
C-video (BNC)
Pin No.
Assignment
1
Composite
2
Ground
S-Video (BNC)
Pin No.
Assignment
1
S-VIDEO/Y (Luma)
2
S-VIDEO/C (Chroma)
3
Ground
37
RS232C (D-Sub 9-pin)
Pin No.
Assignment
1
No Connection
2
TXD
3
RXD
4
No Connection
5
Ground
6
No Connection
7
No Connection
8
No Connection
9
No Connection
SDI (BNC)
Pin No.
Assignment
1
SDI IN
2
SDI OUT
3
Ground
38
RGB HV/RGBS/YPbPr (BNC)
Pin No.
Assignment
RGBS
Y Pb Pr
1
Red
Pr
2
Green
Y
3
Blue
Pb
4
H-Sync / C-Sync
No Connection
5
V-Sync
No Connection
6
Ground
39
Specifications
Model
MD-4221
Type
TFT-LCD
Screen Size
42 inch
Maximum Resolution
1920 X 1080 @ 60Hz
Pixel pitch
0.4845(H) mm X 0.4845(V) mm
Display Colors
16.7M
Contrast Ratio
1300:1
Viewing Angle
89° / 89° / 89° / 89°
Response Time
10msec(Rising+Falling)
Luminance
500cd/m²
Horizontal Frequency
30KHz~93KHz
Vertical Frequency
50Hz~85Hz
Power
Maximum
260W
Consumption
Standby Mode
Typical 17W
Width side
INPUT, -, +, ▼, ▲, PIP, MENU, POWER
Front side
IR Receiver
Input Signal
Video
1XDVI, 1XD-SUB, 1XBNC (CVBS) 2XBNC
(SVHS Y/C), 1XBNC (SDI), 5XBNC
(Component Y/G, Pb/B, Pr/R, H/CS, VS
Input)
Out Signal
Video
1XDVI, 1XBNC (SDI)
Input power
AC 100-240V~, 50-60Hz 3A MAX
Dimension
Size and Weight
LCD Panel
Synchronization
Control key
40
1023.5x615.5x105(mm)/ 29Kg
BARCO MID GENERAL WARRANTY TERMS AND
CONDITIONS
Applicable from Jan 1st 2008
ARTICLE 1: PRODUCT WARRANTY
Barco nv, Medical Imaging Division warrants that the equipment will be free of defects in
workmanship or material for the warranty period or the specific period of a warranty extension
program.
Hardware: Barco warrants that upon delivery hereunder the Products shall (i) conform to its
specifications in effect at the date of delivery and (ii) be free from defects in material and
workmanship (the "Warranties").
Software: Barco warrants that software written by Barco shall perform substantially in accordance
with the specifications in effect at the date of delivery. Software is inherently susceptible to bugs
and errors. Barco makes no warranties with respect to the software which is provided to Customer
on an "as-is" basis and does not warrant uninterrupted or error-free operation of the Products.
Unless otherwise indicated in Barco’s web site or in the agreement between Barco and Customer, the
Warranty Period shall be
(a)
Hardware: 12 months commencing on the Barco date of invoice.
(b)
Software: 3 months commencing on the Barco date of invoice.
Notwithstanding the provisions of clause 2, repair and replacement of defects in material and/or
workmanship under this warranty shall be accomplished in our works according to the terms and
conditions as set forth hereafter:
1.1
Any claim under the Warranties must be notified to Barco in writing within 8 days from the date the
defect or failure has been discovered or noticed the first time. The Customer, upon the occurrence of
any equipment failure, shall contact Barco nv, MID customer support centre (or an authorised service
centre) by telephone, fax or e-mail and shall provide the applicable customer support person with a
complete description of the problem being encountered, including the model and serial number of
the equipment in which the problem has arisen.
1.2
The customer support person shall diagnose the problem experienced by the Customer and shall
advise the Customer on how to proceed. Customer support may ask to return the faulty equipment
or faulty subassemblies to the Barco nv, or a MID customer support centre (or an authorised service
centre) for repair activities. In no event shall Customer return a defective Product or part thereof to
Barco without Barco's prior written approval.
In the event the return to Barco of the defective Product is authorized by Barco, Barco shall issue to
Customer an RMA (Return Material Authorization).
The Customer shall apply for an RMA number to the closest Barco nv, MID Customer support centre (or
an authorised service centre) as listed at www.barcomedical.com, unless otherwise indicated.
The one-way cost of packing, transport and insurance related to shipping the alleged defective
Product or part to Barco for repair or replacement shall be borne by Customer. The one-way cost of
packing, transport and insurance related to shipping of the repaired or replacement Product or part to
Customer shall be borne by Barco.
1.3
The Customer shall return, freight prepaid, the defective equipment or subassemblies in its original
packaging with the assigned RMA number for repair to the Barco nv, MID Customer support centre (or
41
an authorised service centre).
1.4
Replacement parts used shall be new or equivalent to new parts for the revision level of the
equipment. A replacement LCD panel will be new or similar run time. The warranty period for the
replacement parts will expire at the same moment as the original warranty period of the equipment.
All parts replaced hereunder and returned to Barco nv, MID (or an authorised service centre) shall
become the property of Barco nv, MID (or the authorised service centre).
1.5
The repaired equipment shall be returned to the Customer, by regular freight, at Barco nv, MID’s
charge.
1.6
Barco nv, MID will replace a product that fails within 90 days after shipment from Barco with a new
one, ensuring color matching in the event of a diagnostic multi head display configuration.
Barco aims to ship the new replacement product within 2 business days after receipt of the Customers
notification in writing.
ARTICLE 2: CONDITIONS PRECEDENT FOR WARRANTY AND ITEMS EXCLUDED FROM
WARRANTY
A. The Warranties shall apply only to the extent the Products or any parts thereof have
(i) been transported and stored at all times in the original packaging in the conditions as specified
by Barco (such as covered and secure location, minimum and maximum temperature, maximum
humidity, …) or, in absence thereof, at least in conditions consistent with generally accepted practice
for this type of products;
(ii) been handled at all times in accordance with Barco's instructions or, in absence thereof, at least
with the care and caution consistent with generally accepted practice for this type of products;
(iii) been installed strictly in accordance with the instructions and directions given by Barco (if and to
the extent the Products have not been installed by Barco or its authorized subcontractors);
(iv) not been subject to any unauthorized access, alteration, modification or repair or attempts
thereto;
(v) been at all times "normally used" for the intended purpose and operated in strict accordance
with the operating instructions set forth in the operating manual of the Product in question and shall
not have been otherwise misused, abused, damaged. For the purpose hereof, "normally used" shall
mean a regular, ordinary and routine usage of the Product in question as intended and/or
recommended by Barco;
(vi) been maintained at all times in accordance with Barco's instructions or, in absence thereof, at
least with intervals and in a manner consistent with generally accepted practice for this type of
products;
B. The warranty described herein shall not include the following:
2.1
Any hardware or software item procured from a source other than Barco nv, MID or their official agent
or distributor and integrated by Customer or a third party into Barco nv, MID supplied equipment.
2.2
Any host configuration not explicitly supported by Barco nv, MID.
2.3
All software installed on the system, whether they are acquired from Barco nv, MID or third party.
An exception is made for software delivered by Barco nv, MID that would prove to be a cause for the
mal functioning of the hardware covered under this Agreement.
2.4
42
Normal wear and tear, use under circumstances exceeding specifications, such as use in dusty
environment or under excessive temperature conditions, abuse, unauthorised repair or alternation,
lack of proper configuration or maintenance, damaged or modified or removed serial number,
cosmetic refurbishment.
2.5
Repair or replacement of consumables1 or specific parts that by definition are subject to wear and tear,
including but not limited to:
a. CRT’s, LCD panels
b. Backlights in diagnostic LCD displays, when the backlight run time2 is beyond the Guaranteed
Backlight Lifetime3 of that model, when used at the Factory Calibrated Luminance4
Eg1.
• A display is used at 8 hours/day; ie. +/-2.920hours/year
• The display system is covered with a warranty period of 5 year
• The Guaranteed Backlight Lifetime of that model is 17.000hours.
• The Factory Calibrated Luminance cannot be achieved anymore after 4 year, thus
corresponding to +/-11.680hours
• Result: the backlight replacement is performed under warranty
Eg2.
• A display is used at 24 hours/day; ie. 8.760hours/year
• The display system is covered with a warranty program of 5 year
•
The Guaranteed Backlight Lifetime of that model is 17.000hours.
• The Factory Calibrated Luminance cannot be achieved anymore after 2.5years, thus
corresponding to +/-21.900hours
• Result: the backlight replacement does not make part of the warranty coverage.
(1): ‘Consumable’ is a part that can be replaced by the user
(2): ‘Backlight run time’ is the total time that an image (including use of a screen saver) has
been applied to the screen; this value can be consulted via the OSD buttons (On Screen
Display).
(3): ‘Guaranteed Backlight Lifetime’ is the number of backlight hours during which a
predefined luminance value, ie. the Factory Calibrated Luminance, will be provided by a
specific diagnostic display model. This figure is printed on the Warranty certificate of each
display or can be requested at your local Barco office.
(4): ‘Factory Calibrated Luminance’: is the typical luminance value that a specific diagnostic
display model is calibrated at during the production process. This figure is printed on the
Warranty certificate of each display or can be requested at your local Barco office.
c. Lamps, optical components in projectors
d. Replacement because of:
i. image retention as a result of:
- not correctly using screen saver and/or Display Power Management System (DPMS) as
explained in the user manual
- prolonged operation of the display with a static image on the same screen area
ii . a number of missing pixels that is lower than the total allowable number as mentioned
in the product specifications.
iii. difference in color temperature that is lower than the total allowable difference as
mentioned in the product specifications
iv. difference in color temperature as a result of not using all displays of a multi-head
configuration at the same rate.
43
v.
LCD luminance uniformity that is in within the product specifications or luminance
uniformity performance that is inherent to LCD technology.
Barco nv, MID does not warrant a minimum life time nor a performance of any of the consumables.
2.6
Replacement of moveable parts such as power cords, remote controls, …
2.7
Any product disassembly and installation costs at the operation site, travel expenses and travel time
to and from the operation site for the personnel in charge of the repair works and transport charges.
2.8
Any failures resulting from an accident, negligence (such as but not limited to removing or deleting
system files & licensed software product files), misuse, circuit failure or any change, damage due to
fire, water, thunder or lightning, power failure or fluctuation, disruption of communication lines or
due to force majeure, or any reason foreign to the equipment.
2.9
Any specific services or procedures, asked for by Customer, related to verification of repaired
equipment.
2.10 The evaluation cost in case of a returned product deemed functional is not covered under
warranty and will be charged to the Customer, at Barco’s sole discretion, based on a case-by-case
evaluation.
ARTICLE 3: OBLIGATIONS OF THE CUSTOMER
Customer hereby assumes the following obligations as partial consideration for Barco nv, MID
performance of its requirements under the warranty condition; failure by Customer to meet its
obligations under this paragraph shall excuse Barco nv, MID’s performance hereunder:
3.1
Customer shall not expose Barco nv, MID personnel to any unsafe working conditions.
3.2
Repairs to equipment under warranty resulting from improper maintenance or repair performed by
the Customer, or its officers, agents, employees, or representatives, shall be borne by the Customer at
its additional cost and expense.
3.3
The Customer is responsible for installing the Barco nv, MID equipment in an environment for which it
was intended. If there is an indication that the equipment was used – even temporary – outside its
specifications, Barco nv, MID is entitled not to perform warranty repairs and terminate the warranty
agreement. Any actions that have been taken by Barco nv, MID in this respect, may be invoiced to the
Customer at normal pricing.
ARTICLE 4: REMEDIES UNDER WARRANTY
(a) Hardware: If during the Warranty Period a Product or any part thereof, fails to meet any of the
Warranties then, upon Customer's request, Barco shall, at its sole option and cost, promptly and
within 20 working days, either: (i) repair or correct the Product or part in question; or (ii) replace the
Product or supply part(s) or component(s) according to the terms and conditions contained in article 1.
A replacement part shall be at least functionally equivalent to the original part. The replaced Product,
parts and/or components shall become the property of Barco and shall, at Barco's request, be
returned by Customer to Barco at Barco's cost.
(b) Software: Barco's sole obligation shall be to rectify substantial malfunctions of the software (to
the extent technically reasonably possible) by amending the software or supplying an alternative
version of the software.
(c) The repair or replacement under the Warranties covers the cost of material and labor.
44
ARTICLE 5: DISCLAIMER OF WARRANTIES
BARCO NV, MID DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
ARTICLE 6: LIMITATION OF LIABILITY
BARCO NV, MID SHALL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO CUSTOMER OR ANY THIRD PARTY
FOR DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, SUCH AS BUT NOT LIMITED TO,
DAMAGE TO OR LOSS OF TANGIBLE OR INTANGIBLE PROPERTY OR EQUIPMENT, LOSS OF PROFITS OR
REVENUES, COST OF CAPITAL, COST OF PURCHASE OF REPLACEMENT GOODS, OR CLAIMS OF CUSTOMERS OF
USER FOR SERVICE INTERRUPTIONS. THE LIABILITY OF BARCO NV, MID FOR MANUFACTURING, SALE,
DELIVERY, RESALE, INSTALLATION, OPERATION OR SUITABILITY FOR USE OF ANY PRODUCTS OR SERVICES
COVERED BY OR FURNISHED UNDER THIS WARRANTY CONDITION, WHETHER ARISING OUT OF CONTRACT,
NEGLIGENCE, STRICT TORT, WARRANTY OR OTHERWISE, SHALL BE LIMITED TO THE REPAIR OR
REPLACEMENT OF THE PRODUCT OR ANY PART THEREOF WHICH SHALL BE AT CUSTOMER'S SOLE OPTION
AND COST. BARCO’S LIABILITY SHALL NOT EXCEED THE PRICE OF THE ITEM OR ITEMS OF GOODS OR
SERVICES UPON WHICH SUCH LIABILITY IS BASED.
ARTICLE 7: FORCE MAJEURE
Either party shall be released from performance of its obligations under this agreement to the extent,
and for so long as, the performance of this agreement is impeded by reason of force majeure. For
the purposes of this clause the expression "force majeure" means, but shall not be limited to,
industrial dispute, fire, mobilisation, requisition, embargo, currency transfer prohibitions, insurrection,
lack of means of transport, restrictions of the use of energy, and generally any circumstances which
are beyond the control of the parties and hinder performance by one party of his obligations.
ARTICLE 8: GENERAL
8.1
Customer acknowledges its understanding that all software and electronic devices, including Barco nv,
MID products are subject to possible error, mechanical or electrical failure, and should not be relied
upon in inappropriate applications or without proper backup and/or other safety precautions
whenever personal injury or property damage may result from failure or error of the product.
8.2
Barco nv, MID shall not be responsible for machine failure and/or its failure to render service or
maintenance due to causes beyond its reasonable control.
45
46
B410615-01
August 2009
Barco N.V.
President Kennedypark 35
B-8500 Kortrijk, Belgium
visit us at the web: www.barco.com
Support helpdesk:
Asia Pacific: +886-2-8221-6868 ext. 699
Europe, Middle East and Africa: +32 56 233 376
Japan: +81 3 3279 0771
Americas: +1 (678) 475-8262
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising