Char-Broil | 463250910 | Product guide | Char-Broil 463250910 Product guide

Char-Broil 463250910 Product guide
PRODUCT GUIDE
MODEL 463250910
IMPORTANT: Fill out the product record information below.
Serial Number
See rating label on grill for serial number.
Date Purchased
For support and to register your
grill, please visit us at
www.charbroil.com
If you have questions or need
assistance during assembly,
please call 1-888-430-7870.
Estimated assembly time: 30 minutes
The following are trademarks registered by W.C. Bradley Co. in the U.S. Patent and Trademark Office: Caldera®; Charcoal2Go®; Char-Broil®; America's Legendary
Barbeque Company®; American Gourmet®; Bandera®; Brush Hawg®; CB 940®; Char-Diamonds®; Char-Broil Charcoal/Gas®; Everybody Grills®; Everybody
Outside®; FastStart®; Grill 2 Go®; Grill 2 Go® Express®; Grill Lovers®; Infrared Grilling That’s All About U®; Keepers of the Flame®; New Braunfels Smoker
Company®; Patio Bistro®; Patio Caddie®; Patio Kitchen®; Pro-Sear®; RED®; Quantum®; Santa Fe®; Sear and Grill®; Sierra®; Signature Series®; Sure2Burn®;
The Big Easy®; Trentino®; U®; Wild West Tradition®; and the following marks:
®
®
®
The following are trademarks of W.C. Bradley Co.: Advantage Series™; Auto-Clean™;Chef Tested™; Commercial Series™; Designer Series™;; Diamond Flame™;
Double Chef™; Fireball™; Firenzy™; FlavorMaster™;Front Avenue™; Grill 2 Go® Advantage™; Hog and Yard Bird™; H20 Smoker™; Infrared. Grilling’s Juicy Little
Secret™; Incredible Taste. Infallible Results™; Infrared Inside™; Insure™; Let’s Grill Something Together™; Lev-Alert™; Longhorn™; Magneto™; Precision
Flame™; Quick2Burn™; QuickSet™; Ready When You Are™; Season, Set, And Savor™; Sizzle On The Grill™; Signature Series™; SureFire™; The Minute
Grill™;Torchfork™; Universal Grill Parts™; You Bring the Party™
TEC™ is a trademark of Tec Infrared Grills.
Protected under one or more of the following U.S. Patents: 5,421,319; 5,458,309; 5,579,755; 5,996,573; 6,135,104; 6,279,566; 6,331,108; 6,484,900; 6,526,876; 6,595,197; 6,640,799; 6,640,803; 6,729,873; 6,739,473; 6,749,424; 6,792,935; 6,951,213; 7,047,590;
7,516,693; D364,535; D372,637; D373,701; D377,735; D383,035; D397,910; D405,643; D406,005; D406,009 ; D413,043; D413,229; D414,982; D415,388; D416,164; D416,441; D417,587; D417,588; D422,516; D423,274; D423,876; D428,303; D430,772; D435,396;
D436,004; D438,059; D438,060; D438,427; D439,110; D442,505; D443,179; D443,354; D443,464; D447,384; D447,385; D447,909; D448,610; D448,614; D448,615; D448,616; D448,975; D449,492; D450,544; D451,759; D454,028; D454,031; D455,205; D455,206;
D456,202; D456,222; D456,223; D457,789; D458,520; D458,760; D458,802; D459,088; D459,148 D459,149; D459,161; D459,163; D459,586; D459,943; D460,312; D460,313; D460,318; D461,359; D465,123; D465,693; D466,307; D466,439; D466,752; D473,414;
D474,371; D477,498; D477,501; D477,504; D477,506; D477,746; D478,471; D478,472; D480,914; D491,410; D494,009; D494,413; D498,523; D500,359; D504,048; D530,098; D535,000; Canada:D97,504;D99,355; D102,037; D104,200;D108,377; 2,315,567;
France:D010,231;D010,422;D010,590;D010,849; 1,089,646; South Korea: 384,565; United Kingdom: 2,099,402. Other Patents Pending. © 2009 W.C. Bradley Company
© 2009 Char-Broil, LLC Columbus, GA 31902
Printed in China
Assembly instructions © 2009
11/11/09 • G521-001-010801
TABLE OF CONTENTS
DANGER
For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Parts Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-31
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-34
If you smell gas:
1.
2.
3.
4.
Shut off gas to the appliance.
Extinguish any open flame.
Open lid.
If odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department.
Registration Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
WARNING
Safety Symbols
The symbols and boxes shown below explain what each heading
means. Read and follow all of the messages found throughout
the manual.
1. Do not store or use gasoline or other
flammable liquids or vapors in the vicinity of
this or any other appliance.
2. An LP cylinder not connected for use shall not
be stored in the vicinity of this or any other
appliance.
WARNING
WARNING: Indicates an potentially hazardous situation
which, if not avoided, could result in death or serious injury.
CAUTION
CAUTION: Indicates a potentially hazardous situation or
unsafe practice which, if not avoided, may result in minor
or moderate injury.
DANGER
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
CAUTION
For residential use only. Do not use for commercial
cooking.
THIS GRILL IS FOR OUTDOOR USE ONLY.
CAUTION:
Read and follow all safety statements, assembly
instructions, and use and care directions before attempting
to assemble and cook.
INSTALLER/ASSEMBLER:
Leave this manual with consumer.
CONSUMER:
Keep this manual for future reference.
WARNING:
Failure to follow all manufacturer’s instructions could result
in serious personal injury and/or property damage.
CAUTION:
Some parts may contain sharp edges – especially as noted
in the manual! Wear protective gloves if necessary.
2
WARNING
CALIFORNIA PROPOSITION 65
1. Combustion by-products produced when using
this product contain chemicals known to the State of
California to cause cancer, birth defects, and other
reproductive harm.
2. This product contains chemicals, including lead
and lead compounds, known to the State of
California to cause cancer, birth defects or other
reproductive harm.
Wash your hands after handling this product.
CAUTION
Using pots larger than 6 quarts in capacity could
exceed weight limit of the
side burner shelf
or side shelf,
resulting in failure
of grill cart
components.
Installation Safety Precautions
• Use grill, as purchased, only with LP (propane) gas and the
regulator/valve assembly supplied. If your grill is Dual Fuel ready,
a conversion kit must be purchased for use with natural gas.
• Grill installation must conform with local codes, or in their
absence of local codes, with either the National Fuel Gas
Code, ANSI Z223.1/ NFPA 54, Natural Gas and Propane
Installation Code, CSA B149.1, or Propane Storage and
Handling Code, B149.2, or the Standard for Recreational
Vehicles, ANSI A 119.2/NFPA 1192, and CSA Z240 RV Series,
Recreational Vehicle Code, as applicable.
• All electrical accessories (such as rotisserie) must be
electrically grounded in accordance with local codes, or
National Electrical Code, ANSI / NFPA 70 or Canadian
Electrical Code, CSA C22.1. Keep any electrical cords and/or
fuel supply hoses away from any hot surfaces.
• This grill is safety certified for use in the United States and/or
Canada only. Do not modify for use in any other location.
Modification will result in a safety hazard.
WARNING
Do not attempt to repair or alter the
hose/valve/regulator for any “assumed” defect. Any
modification to this assembly will void your warranty
and create the risk of a gas leak and fire. Use only
authorized replacement parts supplied by
manufacturer.
3
USE AND CARE
DANGER
• NEVER store a spare LP cylinder under or near
the appliance or in an enclosed area.
• Never fill a cylinder beyond 80% full.
• An over filled or improperly stored cylinder is a
hazard due to possible gas release from the
safety relief valve. This could cause an intense
fire with risk of property damage, serious injury or
death.
• If you see, smell or hear gas escaping,
immediately get away from the LP
cylinder/appliance and call your fire department.
LP Cylinder Removal, Transport and Storage
•Turn OFF all control knobs and LP cylinder valve. Turn coupling
nut counterclockwise by hand only - do not use tools to
disconnect. Loosen cylinder screw beneath bottom shelf, then
lift LP cylinder up and out of cart. Install safety cap onto LP
cylinder valve. Always use cap and strap supplied with valve.
Failure to use safety cap as directed may result in serious
personal injury and/or property damage.
•A disconnected LP cylinder in LP Cylinder Valve
storage or being transported
must have a safety cap installed (as shown).
Do not store an LP cylinder in enclosed spaces
such as a carport, garage, porch, covered
Safety
patio or other building. Never leave an LP cylinder
Cap
inside a vehicle which may become overheated
Retainer Strap
by the sun.
•Do not store an LP cylinder in an area where children play.
4
LP Cylinder
•The LP cylinder used with your grill must meet the
following requirements:
•Use LP cylinders only with these required measurements: 12"
(30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.)
capacity maximum.
•LP cylinders must be constructed and marked in accordance
with specifications for LP cylinders of the U.S. Department of
Transportation (DOT) or for Canada, CAN/CSA-B339,
cylinders, spheres and tubes for transportation of dangerous
goods. Transport Canada (TC). See LP cylinder collar for
marking.
•LP cylinder valve must have:
•Type 1 outlet compatible with
regulator or grill.
•Safety relief valve.
OPD Hand Wheel
•UL listed Overfill Protection
Device (OPD). This OPD safety
feature is identified by a unique triangular hand wheel. Use
only LP cylinders equipped with this type of valve.
•LP cylinder must be arranged for vapor withdrawal and include
collar to protect LP cylinder valve. Always keep LP cylinders in
upright position during use, transit or storage.
LP cylinder in upright position for vapor withdrawal
LP (Liquefied Petroleum Gas)
•LP gas is nontoxic, odorless and colorless when produced. For
Your Safety, LP gas has been given an odor (similar to rotten
cabbage) so that it can be smelled.
•LP gas is highly flammable and may ignite unexpectedly when
mixed with air.
LP Cylinder Filling
•Use only licensed and experienced dealers.
•LP dealer must purge new cylinder before filling.
•Dealer should NEVER fill LP cylinder more than 80% of LP
cylinder volume. Volume of propane in cylinder will vary by
temperature.
•A frosty regulator indicates gas overfill. Immediately close LP
cylinder valve and call local LP gas dealer for assistance.
•Do not release liquid propane (LP) gas into the atmosphere.
This is a hazardous practice.
•To remove gas from LP cylinder, contact an LP dealer or call a
local fire department for assistance. Check the telephone
directory under “Gas Companies” for nearest certified LP
dealers.
LP Cylinder Exchange
Connecting Regulator to the LP Cylinder
•Many retailers that sell grills offer you the option of replacing
your empty LP cylinder through an exchange service. Use only
those reputable exchange companies that inspect, precision fill,
test and certify their cylinders. Exchange your cylinder only
for an OPD safety feature-equipped cylinder as described
in the "LP Cylinder" section of this manual.
•Always keep new and exchanged LP cylinders in upright
position during use, transit or storage.
•Leak test new and exchanged LP cylinders BEFORE
connecting to grill.
•Place dust cap on cylinder valve outlet whenever the cylinder is
not in use. Only install the type of dust cap on the cylinder valve
outlet that is provided with the cylinder valve. Other types of caps
or plugs may result in leakage of propane.
1.LP cylinder must be properly secured onto grill. (Refer to
assembly section.)
2.Turn all control knobs to the OFF position.
3.Turn LP cylinder OFF by turning hand-wheel clockwise to a
full stop.
4.Remove the protective cap from LP cylinder valve. Always use
cap and strap supplied with valve.
Off
Clockwise
OPD Hand Wheel
LP Cylinder Leak Test
For your safety
•Leak test must be repeated each time LP cylinder is exchanged
or refilled.
•Do not smoke during leak test.
•Do not use an open flame to check for gas leaks.
•Grill must be leak tested outdoors in a well-ventilated area,
away from ignition sources such as gas fired or electrical
appliances. During leak test, keep grill away from open flames
or sparks.
•Use a clean paintbrush and a 50/50 mild soap and water
solution. Brush soapy solution onto areas indicated by arrows
in figure below.
s
Do not use household cleaning agents. Damage to gas
train components can result.
Type 1 outlet with
thread on outside
Safety Relief Valve
Strap and Cap
Do not use a POL transport plug
(plastic part with external threads)!
It will defeat the safety feature of
the valve.
5.Hold regulator and insert nipple into LP
cylinder valve. Hand-tighten the
coupling nut, holding regulator in a
straight line with LP cylinder valve so
as not to cross-thread the connection.
Nipple has to be centered
into the LP cylinder valve.
WARNING
If “growing” bubbles appear do not use or move the LP
cylinder. Contact an LP gas supplier or your fire
department!
5
Leak Testing Valves, Hose and Regulator
1.Turn all grill control knobs to OFF.
2.Be sure regulator is tightly connected to LP cylinder.
Str
aig
ht
Hold coupling nut and regulator
as shown for proper connection
to LP cylinder valve.
3.Completely open LP cylinder valve by turning hand wheel
counterclockwise. If you hear a rushing sound, turn gas off
immediately. There is a major leak at the connection. Correct
before proceeding.
4.Brush soapy solution onto areas circled below, or other similar
fittings on your grill.
6.Turn the coupling nut clockwise and tighten to a full stop. The
regulator will seal on the back-check feature in the LP cylinder
valve, resulting in some resistance. An additional one-half to
three-quarters turn is required to complete the
connection. Tighten by hand only – do not use tools.
NOTE:
If you cannot complete the connection, disconnect regulator and
repeat steps 5 and 6. If you are still unable to complete the
connection, do not use this regulator!
DANGER
• Do not insert any tool or foreign object into the valve
outlet or safety relief valve. You may damage the valve
and cause a leak. Leaking propane may result in
explosion, fire, severe personal injury, or death.
WARNING
• Outdoor gas appliance is not intended to be installed
in or on a boat.
• Outdoor gas appliance is not intended to be installed
in or on an RV.
• Never attempt to attach this grill to the self-contained
LP gas system of a camper trailer or motor home.
• Do not use grill until leak-tested.
• If a leak is detected at any time, STOP and call the fire
department.
• If you cannot stop a gas leak, immediately close
LPcylinder valve and call LP gas supplier or your fire
department!
6
NOTE: Sideburner
shelf fascia not
shown for clarity.
NOTE: Your grill
may NOT be
equipped with a
sideburner.
5.If “growing” bubbles appear, there is a leak. Close LP
cylinder valve immediately and retighten connections. If leaks
cannot be stopped do not try to repair. Call for replacement
parts.
6.Always close LP cylinder valve after performing leak test by
turning hand wheel clockwise.
WARNING
For Safe Use of Your Grill and to Avoid Serious
Injury:
• Do not let children operate or play near grill.
• Keep grill area clear and free from materials that burn.
• Do not block holes in sides or back of grill.
• Check burner flames regularly.
• Use grill only in well-ventilated space. NEVER use in
enclosed space such as carport, garage, porch,
covered patio, or under an overhead structure of any
kind.
• Do not use charcoal or ceramic briquets in a gas grill.
(Unless briquets are supplied with your grill.)
• Use grill at least 3 ft. from any wall or surface.
Maintain 10 ft. clearance to objects that can catch fire
or sources of ignition such as pilot lights on water
heaters, live electrical appliances, etc.
Safety Tips
 Before opening LP cylinder valve, check the coupling nut for
tightness.
 When grill is not in use, turn off all control knobs and LP
cylinder valve.
 Never move grill while in operation or still hot.
 Use long-handled barbecue utensils and oven mitts to avoid
burns and splatters.
 Maximum load for sideburner and side shelf is 10 lbs.
 The grease tray must be inserted into grill and emptied after
each use. Do not remove grease tray until grill has
completely cooled.
 Clean grill often, preferably after each cookout. If a bristle
brush is used to clean any of the grill cooking surfaces,
ensure no loose bristles remain on cooking surfaces prior to
grilling. It is not recommended to clean cooking surfaces
while grill is hot.
 If you notice grease or other hot material dripping from grill
onto valve, hose or regulator, turn off gas supply at once.
Determine the cause, correct it, then clean and inspect valve,
hose and regulator before continuing. Perform a leak test.
 Keep ventilation openings in cylinder enclosure (grill cart) free
and clear of debris.
 Do not store objects or materials inside the grill cart
enclosure that would block the flow of combustion air to the
underside of either the control panel or the firebox bowl.
 The regulator may make a humming or whistling noise during
operation. This will not affect safety or use of grill.
 If you have a grill problem see the "Troubleshooting Section".
 If the regulator frosts, turn off grill and LP cylinder valve
immediately. This indicates a problem with the cylinder and it
should not be used on any product. Return to supplier!
CAUTION
• Putting out grease fires by closing the lid is not possible.
Grills are well ventilated for safety reasons.
• Do not use water on a grease fire. Personal injury may
result. If a grease fire develops, turn knobs and LP
cylinder off.
• Do not leave grill unattended while preheating or burning
off food residue on HI. If grill has not been regularly
cleaned, a grease fire can occur that may damage the
product.
• Apartment Dwellers:
Check with management to learn the requirements
and fire codes for using an LP gas grill in your
apartment complex. If allowed, use outside on the
ground floor with a three (3) foot clearance from walls
or rails. Do not use on or under balconies.
• NEVER attempt to light burner with lid closed. A
buildup of non-ignited gas inside a closed grill is
hazardous.
• Never operate grill with LP cylinder out of correct
position specified in assembly instructions.
• Always close LP cylinder valve and remove
coupling nut before moving LP cylinder from
specified operation position.
Main Burner Ignitor Lighting
 Do not lean over grill while lighting.
1. Turn
OFF all Gas Burner Control Valves.
2. Turn ON gas source or tank.
3. Open lid during Lighting.
4. Push in and turn AUTO-CLEAN valve to COOK position.
5. To ignite any main burner, turn the main burner control
knob to the
position.
6. Push and hold ELECTRONIC IGNITOR button until the
burner lights.
7. Once burner has ignited, turn knob to desired setting.
8. If Ignition does not occur in 5 seconds, turn the burner
control to
OFF, wait 5 minutes, and repeat the lighting
procedure.
9. Repeat steps 4 through 7 for the remaining main burners.
Lighting instructions continued on next page.
7
WARNING
Turn controls and gas source or tank OFF when not
in use.
CAUTION
If ignition does NOT occur in 5 seconds, turn the
burner controls OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
Burner Flame Check
•Remove cooking grates and troughs. Light burners, rotate
knobs from
to . You should see a smaller flame in
position than seen on
. Perform burner flame check
on sideburner, also. Always check flame prior to each use. If
only low flame is seen refer to "Sudden drop or low flame" in
the Troubleshooting Section.
Turning the Grill OFF with AUTO-CLEAN™
With the Autoclean feature you have two choices for turning off
your grill; Manual and AUTO-CLEAN™
Manual Method
Match-Lighting
• Turn all knobs, including the AUTO-CLEAN™ valve, to the OFF
 Do not lean over grill while lighting.
position.
1. Turn
OFF all gas burner control valves.
OFF the LP cylinder by turning the handwheel
• Turn
2. Turn ON gas at LP cylinder.
clockwise to a full stop.
3. Open lid during lighting.
NOTE: Always follow the lighting instructions found in the
4. Push in and turn the AUTO-CLEAN™ valve to the COOK position. instruction manual and also located on the inside of the cabinet
5. Place match into match holder (hanging from side of cart).
door prior to using the Auto-Clean feature. Grill must be ignited
Light match, place into lighting hole on right or left side of
prior to using the Auto-Clean feature.
firebox.
AUTO-CLEAN™ Method
6 .Push in and turn far right or far left knob to
position. Be
• After cooking is complete, set all main burner grill knobs to the
sure burner lights and stays lit.
setting and close the grill lid. (AUTO-CLEAN™ shutdown
7. If ignition does NOT occur in 5 seconds, turn the burner
should not be used on the sideburner.)
control knob
OFF, wait 5 minutes, and repeat the lighting
• Push in and turn the AUTO-CLEAN™ knob to the CLEAN position.
procedure.
• Once at the CLEAN position, release the knob and the green light
8. Light other burners by pushing knob in and turning to
should begin blinking.
position. If your grill has two cooking zones, repeat steps 4
The valve will now stay on for 15 minutes before turning off the
•
through 6 for the remaining section of the grill.
gas to the burners.
• After the clean cycle is complete, turn all knobs including
the AUTO-CLEAN™ valve to the OFF
position.
• Turn OFF the LP cylinder by turning the handwheel clockwise
to a full stop.
For safety in storing a grill, the LP cylinder should always be turned
OFF.
Side Burner Lighting Instructions:
If red light comes on while green light is flashing, the batteries will
s
Do not lean over grill while lighting.
need to be replaced very soon.
1. Turn
OFF all gas burner control valves.
When changing the batteries, please replace both batteries at the
2. Turn ON gas source or tank.
same time. Always replace with new batteries of the same type.
3. Open lid during lighting.
4. Push in and turn AUTO-CLEAN™ valve to COOK position.
Ignitor Check
5. To ignite SIDEBURNER, turn sideburner knob to the
• Turn gas off at LP cylinder. Press and hold electronic ignitor
position.
button. "Click" should be heard and spark seen each time
6. Push and hold the ELECTRONIC IGNITOR button untill the
between each collector box or burner and electrode. See
"Troubleshooting" if no click or spark.
sideburner lights.
7. Once burner has ignited, turn knob to desired setting.
Valve Check
8. If ignition does not occur in 5 seconds, turn the burner control
• Important: Make sure gas is off at LP cylinder before
to
OFF, wait 5 minutes, and repeat the lighting procedure.
checking valves. Knobs lock in OFF position. To check
valves, first push in knobs and release, knobs should spring
Sideburner Match Lighting
back. If knobs do not spring back, replace valve assembly
1. Turn
OFF all burner control valves.
before using grill. Turn knobs to LOW position then turn back to
2. Open sideburner lid. Turn on
OFF
position. Valves should turn smoothly.
gas at LP cylinder.
Hose Check
3. Place lit match near burner.
• Before each use, check to see if hoses are cut or worn.
4. Turn sideburner knob to
.
Replace damaged hoses before using grill. Use only
Be sure burner lights and stays lit.
valve/hose/regulator specified by manufacturer.
8
General Grill Cleaning
•Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory (and should never be painted). Apply a strong solution
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry. Do not apply a caustic grill/oven cleaner to painted
surfaces.
• Plastic parts: Wash with warm soapy water and wipe dry.
 Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
•Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use nonabrasive scouring powder
for stubborn stains.
•Painted surfaces: Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
nonabrasive cloth.
•Stainless steel surfaces: To maintain your grill’s high quality
appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic cleaning
pad. Use only in direction of brushed finish to avoid damage.
Do not use abrasive pad on areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean any of
the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.
CAUTION
SPIDER ALERT!
SPIDER AND WEBS
INSIDE BURNER TUBE
If you notice that your grill is getting hard to light or that the
flame isn’t as strong as it should be, take the time to check and
clean the venturi’s.
VALVE
CONTROL PANEL
SPIDER WEBS
INSIDE VENTURI
BURNER
Storing Your Grill
•Clean cooking grates.
•Store in dry location.
•When LP cylinder is connected to grill, store outdoors in a wellventilated space and out of reach of children.
•Cover grill if stored outdoors. Choose from a variety of grill
covers offered by manufacturer.
•Store grill indoors ONLY if LP cylinder is turned off and
disconnected, removed from grill and stored outdoors.
•When removing grill from storage, follow “Cleaning the Burner
Assembly” instructions before starting grill.
In some areas of the country, spiders or small insects have been
known to create “flashback” problems. The spiders spin webs, build
nests and lay eggs in the grill’s venturi tube(s) obstructing the flow of
gas to the burner. The backed-up gas can ignite in the venturi behind
the control panel. This is known as a flashback and it can damage
your grill and even cause injury.
To prevent flashbacks and ensure good performance the burner and
venturi assembly should be removed from the grill and cleaned
before use whenever the grill has been idle for an extended period.
9
Cleaning the Burner Assembly
Follow these instructions to clean and/or replace parts of burner
assembly or if you have trouble igniting grill.
1. Turn gas OFF at control knobs and LP cylinder.
2. Remove cooking grates and flame tamers.
3. Remove screws and carryover tubes from rear of burners.
4. Remove screw and washers to disengage burner from
bracket on firebox.
5. Remove screws to detach electrode from burner. Electrode
should remain in firebox.
6. Carefully lift each burner up and away from valve openings.
We suggest three ways to clean the burner tubes. Use the one
easiest for you.
(A) Bend a stiff wire (a light weight coat hanger works well)
into a small hook. Run the hook through each burner
tube several times.
(B) Use a narrow bottle brush with a flexible handle (do not
use a brass wire brush), run the brush through each
burner tube several times.
(C) Wear eye protection: Use an air hose to force air into
the burner tube and out the burner ports. Check each
port to make sure air comes out each hole.
7. Wire brush entire outer surface of burner to remove food
residue and dirt.
8. Clean any blocked ports with a stiff wire such as an open
paper clip.
9. Check burner for damage, due to normal wear and corrosion
some holes may become enlarged. If any large cracks or
holes are found replace burner.
VERY IMPORTANT: Burner tubes must reengage valve
openings. See illustrations at right.
Correct
burner-to-valve
engagement
10.
11.
12.
13.
Attach electrode to burner.
Carefully replace burners.
Attach burners to brackets on firebox.
Reposition carryover tubes and attach
to burners. Replace flame tamers and cooking grates.
Burner
Electrode
10
Grill Halogen Light
2.
1.
LIGHT OPERATION INSTRUCTIONS
3.
1. Make sure light switch on the control panel is in the “OFF” position.
ON
ON
2. Connect light plug to an extension cord, then put the extension
cord plug into the outlet on the wall.
OFF
OFF
3. Turn the light switch to “ON”.
Light plug
WARNING
Extension cord,
for out door use
˙ Keep any electrical supply cord away from any
heated surface.
˙ Use the shortest length extension cord required.
Do not connect 2 or more extension cords together.
Bulb Replacement
▲ Make sure light switch on the control panel is in the “OFF” position and adapter plug is disconnected from outlet.
Step 2
Step 1
Step 3
Release the screw securing the light
socket.
Take out the socket and remove the lens.
Step 4
Loosen the two screws which are
locking the bulb.
Step 5
Reverse instructions from step 3
through step 1 to re-install socket.
Pull out the bulb and replace
with a new bulb.
Bulb Specification
Bulb Type: Halogen
Wattage: 10 W per bulb
Voltage: 12 V
CAUTION
Take care not to touch the bulb with your bare fingers.
Touching bulb with your skin can leave a film on the
bulb that causes it to burn out quickly.
Continued on next page
11
Cleaning the Lens
1. Prior to cleaning, make sure the light switch is in the “OFF” position and the light plug is
disconnected from the power supply.
2. Do not clean the glass lens when warm. Allow to cool before cleaning. Sudden change in
temperature may cause cracking of the glass lens.
3. Use a damp towel to clean the surface of the glass lens.
4. Allow the lens to dry before reconnecting the light plug to the power supply and turning the
light switch to the “ON” position.
IMPORTANT
• Since 1971 the National Electric Code (NEC) has required Ground Fault Interrupter devices on all outdoor
circuits.
• If your residence was built before 1971, check with a qualified electrician to determine if a Ground Fault
Interrupter protector exists.
• Do not use this appliance if the circuit does not have GFI protection.
• Do not plug this appliance into an indoor circuit.
WARNING
1. To protect against electric shock, do not immerse cord or plugs in water or other liquid.
2. Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts.
3. Do not operate grill with a damaged cord, plug, or after the appliance malfunctions or has been damaged in any manner.
4. Do not let the cord hang over the edge of a table or touch hot surfaces.
5. Do not use an outdoor cooking gas appliance for purposes other than intended.
6. When connecting, first connect plug to the outdoor cooking gas appliance then plug appliance into the outlet.
7. Use only a Ground Fault Interrupter(GFI) protected circuit with this outdoor cooking gas appliance.
8. Never remove the grounding plug or use with an adapter of 2 prongs.
9. Use only extension cords with a 3 prong grounding plug, rated for the power of the equipment, and approved for
outdoor use with a W-A marking.
12
LIMITED WARRANTY
This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this
product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods
indicated below beginning on the date of purchase*. The manufacturer reserves the right to require that defective parts be returned, postage and or
freight pre-paid by the consumer for review and examination.
SCOPE OF COVERAGE
Stainless Burner
Firebox and Lid
All Other Parts
PERIOD OF COVERAGE
Limited Lifetime
2 years from date of purchase*
1 year from date of purchase*
TYPE OF FAILURE COVERAGE
PERFORATION, MANUFACTURING,
AND MATERIAL DEFECTS ONLY
*Note: A dated sales reciept WILL be required for warranty service.
The original consumer-purchaser will be responsible for all shipping charges for parts replaced under the terms of this limited warranty.
This limited warranty is applicable in the United States and Canada only, is only available to the original owner of the product and is not transferable.
Manufacturer requires proof of your date of purchase. Therefore, you should retain your sales slip or invoice. Registering your product is not a
substitute for proof of purchase and the manufacturer is not responsible for or required to retain proof of purchase records.
This limited warranty applies to the functionality of the product ONLY and does not cover cosmetic issues such as scratches, dents, corrosions or
discoloring by heat, abrasive and chemical cleaners or any tools used in the assembly or installation of the appliance, surface rust, or the
discoloration of stainless steel surfaces. RUST is not considered a manufacturing or materials defect.
This limited warranty will not reimburse you for the cost of any inconvenience, food, personal injury or property damage.
ITEMS MANUFACTURER WILL NOT PAY FOR:
1. Shipping cost, standard or expedited, for warranty and replacement parts
2. Service calls to your home.
3. Repairs when your product is used for other than normal, single-family household or residential use.
4. Damage, failures, or operating difficulties resulting from accident, alteration, careless handling, misuse, abuse, fire, flood,
acts of God, improper installation or maintenance, installation not in accordance with electrical or plumbing codes, or use
of products not approved by the manufacturer.
5. Any food loss due to product failures or operating difficulties.
6. Replacement parts or repair labor costs for units operated outside the United States or Canada.
7. Pickup and delivery of your product.
8. Repairs to parts or systems resulting from unauthorized modifications made to the product.
9. The removal and/or reinstallation of your product.
DISCLAIMER OF IMPLIED WARRANTIES and LIMITATION OF REMEDIES
Repair or replacement of defective parts is your exclusive remedy under the terms of this limited warranty. In the event of parts availability issues,
the manufacturer reserves the right to substitute like or similar parts that are equally functional.
Manufacturer will not be responsible for any consequential or incidental damages arising from the breach of either this limited warranty or any
applicable implied warranty, or for failure or damage resulting from acts of God, improper care and maintenance, grease fire, accident, alteration,
replacement of parts by anyone other than Manufacturer, misuse, transportation, commercial use, abuse, hostile environments (inclement weather,
acts of nature, animal tampering), improper installation or installation not in accordance with local codes or printed manufacturer instructions.
THIS LIMITED WARRANTY IS THE SOLE EXPRESS WARRANTY GIVEN BY THE MANUFACTURER. NO PRODUCT PERFORMANCE
SPECIFICATION OR DESCRIPTION WHEREVER APPEARING IS WARRANTED BY MANUFACTURER EXCEPT TO THE EXTENT SET
FORTH IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTY PROTECTION ARISING UNDER THE LAWS OF ANY STATE,
INCLUDING IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE, IS HEREBY
LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY.
Neither dealers nor the retail establishment selling this product has any authority to make any additional warranties or to promise remedies
in addition to or inconsistent with those stated above. Manufacturer's maximum liability, in any event, shall not exceed the purchase price of the
product paid by the original consumer.
NOTE: Some states do not allow an exclusion or limitation of incidental or consequential damages, so some of the above limitations or exclusions
may not apply to you. This limited warranty gives you specific legal rights as set foth herein. You may also have other rights which vary from state
to state. In the state of California only, if refinishing or replacement of the product is not commercially practicable, the retailer selling this product or
the Manufacturer will refund the purchase price paid for the product, less the amount directly attributable to use by the original consumer-purchaser
prior to discovery of the nonconformity. In addition, in the state of California only, you may take the product to the retail establishment selling this
product in order to obtain performance under this limited warranty.
If you wish to obtain performance of any obligation under this limited warranty, you should
write to:
Consumer Relations
P. O. Box 1240
Columbus, GA 31902-1240
Consumer returns will not be accepted unless a valid Return Authorization is first acquired. Authorized returns are clearly marked on the outside of
the package with an RA number and the package is shipped freight/postage pre-paid. Consumer returns that do not meet these standards will be
refused.
13
PARTS LIST
Key
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Qty
1
1
1
2
1
2
1
1
1
1
1
1
4
1
2
P
Q & QQ
R
S
T
U
V
W
X
Y
Z
AA
BB
CC
DD
EE
FF
GG
HH
II
JJ
KK
LL
MM
NN
1
1
1
4
1
5
2
1
1
1
1
1
1
2
1
1
3
1
2
2
1
1
1
1
2
Description
TOP LID
TOP LID, INNER LINER
LOGO PLATE, W/ TEMP GAUGE
HANDLE END, TOP LID
HANDLE, TOP LID
RUBBER BUMPER, RECTANGLE, F/ TOP LID
HARDWARE F/ TOP LID ASSEMBLY
FIREBOX
PANEL, LEFT, F/ FIREBOX
PANEL, RIGHT, F/ FIREBOX
HEAT SHIELD, FIREBOX
UPPER PANEL, REAR, FIREBOX
MAIN BURNER
ELECTRODE SET, F/ LEFT, MAIN BURNER
ELECTRODE SET, F/ MIDDLE & RIGHT,
MAIN BURNER
ELECTRODE, F/ FAR RIGHT, F/ MAIN BURNER
HOSE VALVE REGULATOR
MAIN CONTROL PANEL
BEZEL F/ CONTROL KNOB
LOWER PANEL, REAR, FIREBOX
CONTROL KNOB
MATCH HOLDER AND CHAIN ASSY
LOWER PANEL, LEFT, CART
LOWER PANEL, RIGHT, CART
ELECTRONIC IGNITION MODULE
HEAT SHIELD, F/ ELECTRONIC MODULE
IGNITOR WIRE, F/ SIDEBURNER
LOWER PANEL, REAR, CART
GROMMET
HEAT SHIELD, F/ TANK
IGNITER SWITCH MODULE
HOSE CLIP
BOTTOM SHELF
CASTER, LOCKING
CASTER, FIXED
12 VOLT ADAPTER
UPPER DOOR BRACE
SWITCH, F/ LIGHT
LIGHT ASSEMBLY
COVER, F/ LIGHT
Key
OO
PP
RR
SS
TT
UU
VV
WW
XX
YY
ZZ
AAA
BBB
CCC
DDD
EEE
FFF
GGG
HHH
III
JJJ
KKK
LLL
MMM
NNN
OOO
PPP
QQQ
RRR
Qty
1
2
1
4
1
1
1
1
4
1
1
1
2
2
1
1
1
1
1
1
1
2
2
1
2
1
1
2
1
NOT Pictured
…
1
…
2
…
1
…
1
…
1
Description
DOOR, RIGHT, NO HANDLE
TROUGH
WARMING RACK
COOKING GRATE
SIDEBURNER SHELF
CONTROL PANEL, LEFT SIDE SHELF
DRIP PAN INSERT
LID, F/ SIDEBURNER
HANDLE, F/ SB / DOORS
SIDEBURNER
ELECTRODE, F/ SIDEBURNER
GRATE, F/ SIDEBURNER
DRAWER FRONT
DRAWER FRAME
RIGHT SIDE SHELF
CONTROL PANEL, RIGHT SIDE SHELF
RIGHT PANEL F/ DRAWER
UPPER PANEL F/ DRAWER
HEAT SHIELD, LOWER, FIREBOX
CAP, F/ ELECTRONIC IGNITION MODULE
BEZEL F/ SIDEBURNER CONTROL KNOB
RUBBER BUMPER, ROUND
SB LID BUMPER
TANK SCREW
HINGES, F/ SB LID
BEZEL, F/ AUTO CLEAN KNOB
CONTROL KNOB F/ AUTO CLEAN
PIN, F/ DOOR
TROUGH MIDDLE BRACKET
CASTER WRENCH
DOOR MAGNET
HARDWARE PACK
ASSEMBLY MANUAL, ENGLISH
ASSEMBLY MANUAL, SPANISH
NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from
those on your particular grill model. However, the method of assembly remains the same.
14
PARTS DIAGRAM
G
A
QQQ
B
KKK
C
F
F
NNN
T
AA
LLL
D
L
NN
D
J
E
FF
H
MM
RR
FF
M
WW
XX
VV
I
V
O
N
O
V
FF
P
SS
K
AAA
UU
EE
DD
S
YY
U
JJJ
U
R
DDD
LL
GGG
FFF
CCC
HHH
QQ
ZZ
TT
PP
RRR
Q
JJ
Z
KK
EEE
III
PPP
BBB
Y
XX
CC
CC
BB
XX OOO
OO
CCC
BBB
XX
W
GG
II
HH
X
MMM
15
ASSEMBLY
1
Attach the two locking casters at the rear of the bottom shelf and the two fixed casters at the front.
Use the provided caster wrench to fully tighten casters.
Fixed caster
Locking caster
Front
Rear
Bottom shelf
2
Attach side panels to bottom shelf using three
1/4-20x1/2” screws, 7mm lock washers, and
7mm flat washers per panel.
IMPORTANT: Panel with large hole must
Be on Right side of bottom shelf.
1/4-20x1/2” screw
7mm lock washer
7mm flat washer
Left side panel
Make sure side panels
are pushed as far to the
rear of bottom shelf as
possible before fully
tightening screws.
Right side panel
(with large hole)
Front
Magnet
16
3
Place lower back panel between side panels at rear of bottom shelf. Make sure the adapter is positioned as shown. Secure
lower back panel to side panels using two 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers on each side.
Secure lower back panel to bottom shelf using one 1/4-20x1/2” screw, 7mm lock washer, and 7mm flat washer.
7mm lock washer
7mm flat washer
1/4-20x1/2” screw
Lower back panel
17
4
Attach drawer right panel to bottom shelf using three #10-24x3/8” screws, 5mm lock washers and 5mm flat washers.
Drawer right panel
#10-24x3/8” screw
5mm lock washer
Bottom
5
shelf
5mm flat washer
On back of grill, attach drawer right panel to lower back panel using two #8x3/8” self-tapping screws.
Drawer right panel
#8x3/8”
self-tapping screw
Lower ba
ck panel
18
6
Attach drawer upper panel to drawer right panel using three #8x3/8” self-tapping screws. Attach drawer upper panel to cart
left side panel using two #8x3/8” self-tapping screws.
Drawer upper panel
#8x3/8”
self-tapping screw
#8x3/8”
self-tapping screw
Ca
rt l
7
eft
sid
ep
ane
l
Drawer right panel
Inside of cart, attach middle of upper back panel to lower back panel using one 1/4-20x1/2” screw, 7mm lock washer and
7mm flat washer.
el
ack pan
Upper b
1/4-20x1/2”
screw
7mm lock
washer
7mm flat washer
el
ack pan
Lower b
19
8
Insert front brace between cart side panels. Make sure door hinge pins are on the top side and facing the front.
Secure using one 1/4-20x1½” screw, 7mm lock washer and 7mm flat washer on each side.
el
ack pan
Upper b
Hinge pin
ace
Front br
7mm flat
washer
9
7mm lock
washer
Insert tank heat shield tabs(w/o holes) into slots between upper back panel and lower back panel, shown A.
Attach tank heat shield front tabs(w/ holes) under front brace using two #8X3/8” self-tapping screws, shown B.
A
B
el
ack pan
Upper b
Front brace
Tank heat shield
hield
eat s e up)
h
k
n
sid
Ta
cave
(con
20
#8x3/8”
self-tapping screw
#8x3/8”
self-tapping screw
1/4-20x1½”
screw
10
This step requires two people to lift and position grill head onto cart. Carefully lower the grill
head onto the cart, aligning slots at bottom of grill head with posts on cart side panels. Make sure the
regulator hose is hanging outside the cart. Grill head must face open side of cart.
Grill head
Regulator hose
11
Inside of cart, connect adapter wire harness and light wire harness.
Light wire harness
Adapter wire harness
Lower back panel
(Inside)
Adapter
21
12
Secure front brace in upper hole with one 1/4-20x1½” screw, 7mm lock washer, 7mm flat washer.
Secure upper back panel in lower hole with one 1/4-20x1½” screw, 7mm lock washer, 7mm flat washer.
Only left side shown for assembly, repeat above steps for right side.
7mm flat washer
1/4-20x1½” screw
Upper back
panel
7mm lock washer
7mm lock washer
7mm flat washer
13
1/4-20x1½” screw
In side of the cart, connect the wires from burner electrodes into the back of Electronic Ignition module. Total (5) connections.
Connect the two wires [(a) and (b)] from switch wiring harness into the back of Electronic Ignition module. Total (2)
connections, shown A.
Note: Switch terminals are larger than electrode terminals and should only be installed in location shown as (a),(b).
Release the cap and nut from electronic ignition module. Attach electronic ignition module to the cart right side panel
with the nut, shown B.
Insert AA battery into ignition module, negative (–) end first. Then put on the cap, shown C.
A
B
Nut
Electronic ignition
module
Right side panel
Tie wrap
1
2
NOTE: Wires omitted for
clarity of illustration
(a)
3
4
(b)
C
Right side panel
5
-
+
Electronic ignition module
AA battery
22
Cap
14
Attach right side fascia to right side shelf using four #10-24x3/8” screws,5mm lock washers and 5mm flat washers, shown A.
Insert flange on right side shelf into side shelf brackets on right side of firebox, shown B.
Remove the four screws and washers factory attached to the Auto Clean valve bracket. Position Auto Clean valve bracket
beneath right side shelf fascia so that valve stem comes through larger center hole in fascia. Align the four holes on valve
bracket with the four holes on fascia. Secure using screws and washers that were removed from bracket, shown C.
A
5mm Flat Washer
5mm Lock Washer
#10-24x3/8” Screw
B
side shelf bracket
C
Right side fascia
Screws and Washers removed
from valve bracket
Valve stem
Auto clean valve
bracket
23
15
Attach rear of right side shelf using one 1/4-20x1/2” screw, 7mm lock washer and 7mm flat washer in upper hole.
And using 1/4-20x1½” screw, 7mm lock washer, 7mm flat washer in lower hole, shown A.
Attach front of shelf and fascia using three 1/4-20x1/2” screws, 7mm lock washers and 7mm flat washers, shown B.
Place the small bezel over valve stem on front side of the fascia. Align small holes on bezel with the holes on fascia.
Attach using two #8-32x3/8” screws and 4mm lock washers. Press control knob on to valve stem, shown C.
A
7mm flat
washer
7mm lock
washer
7mm flat
washer
B
C
1/4-20x1/2”
screw
7mm lock
washer
7mm lock
washer
4mm lock washer
1/4-20x1/2”
screw
1/4-20x1½”
screw
7mm flat
washer
#8-32x3/8” screw
Small knob
Valve stem
24
Small bezel
16
Attach left side fascia to left side shelf using four #10-24x3/8” screws, 5mm lock washers and 5mm flat washers, shown A.
Place side burner lid onto left side shelf and align hinge holes in back of lid with shelf holes. Secure lid to the shelf using four
#8-32x3/8” screws, 4mm flat washers, 4mm lock washers, and #8-32 hex nuts, shown B.
Insert flange on left side shelf into side shelf brackets on side of firebox, shown C.
A
5mm Lock
washer
5mm Flat
washer
Lef
t si
#10-24x3/8”
screw
Lef
t si
de
de
fas
cia
she
lf
B
urner
Side b
lid
#8-32x3/8” screw
Hinge
lf
e she
id
Left s
4mm flat
washer
4mm lock
washer
#8-32 hex nut
C
side shelf bracket
Le
ft s
ide
sh
elf
25
17
Attach rear of left side shelf using one 1/4-20x1½” screw, 7mm lock washer and 7mm flat washer in lower hole, using one
1/4-20x1/2” screw, 7mm lock washer and 7mm flat washer in upper hole, shown A.
Attach three 1/4-20x1/2” screws, 7mm lock washers, 7mm flat washers at the front of shelf, shown B.
A
B
1/4-20x1/2” Screw
7mm Lock Washer
7mm Flat Washer
1/4-20x1-1/2” Screw
1/4-20x1/2”
Screw
7mm Lock Washer
7mm Flat Washer
7mm Flat
Washer
18
7mm Lock
Washer
First, remove the two screws and lock washers factory attached to the sideburner valve bracket. Position sideburner
valve bracket beneath sideburner shelf fascia so that valve stem comes through larger center hole in fascia. Align the holes
on valve bracket with left and right holes on fascia. Secure using lock washers and screws that were removed from bracket.
Next, place sideburner bezel over valve stem on front side of fascia. Align small holes on bezel with upper and lower holes on
fascia. Attach using two #8-32x3/8” screws and 4mm lock washers. Press sideburner control knob onto valve stem.
Note: Use left and right
holes on fascia to
Screws and Washers
attach valve bracket
removed from valve bracket
Note: Use upper and lower
holes on fascia to
attach bezel
Control knob
#8-32x3/8” screw
4mm
lock washer
Sideburner
fascia
Side burner
bezel
Valve stem
26
Sideburner
valve bracket
Note: Make sure set the bezel with
longer slot at the top
19
8a
Insert sideburner burner into left shelf. The stud on bottom of burner fits into rear small hole in sideburner drip pan on
shelf, shown A. Secure burner to sideburner drip pan with one Wing nut, shown B. Under sideburner shelf, attach
sideburner ignitor wire to electrode. Make sure burner tube engages sideburner valve, shown C.
B
sideburner drip pan
A
sideburner burner
Wing nut
valv
e
C
be
er tu
burn
sideburner drip pan
electrode
ignitor wire
20
Place side burner cooking grate onto side burner shelf.
r cooking
sideburne
grate
27
the pin on bottom of door into hole in bottom shelf. Press upper hinge pin in front brace, align hinge hole on top of
21
8a Insert
door, and release hinge pin into door.
PRESS
Top of
door
Right door
pin
on bottom
of door
22
Attach drawer front panel to drawer using four #10-24x3/8” screws, 5mm lock washers and 5mm flat washers. Two drawers
totally.
Dr
aw
er
5mm Flat Washer
5mm Lock Washer
Drawer
28
#10-24x3/8” Screw
fro
nt
pa
ne
l
23
Slide one drawer along lower tracks into cart left. Slide the other drawer along upper tracks into the cart.
Drawer
24
Place troughs onto fire box. Align the trough pins with the holes on fire box. Make sure trough is put in the right direction.
Troughs
29
25
Place cooking grates onto the firebox as shown.
Insert the four wire ends at rear of warming rack into holes in back of fire box. Front wires of warming rack rest on
sides of firebox.
Assembled
warming rack
26
On back of right side fascia, open battery box by sliding its cover. Put two AA batteries in the box and then replace the cover.
Battery box
Cover
AA battery
30
27
LP CYLINDER IS SOLD SEPARATELY. Fill and leak check the cylinder before attaching to grill and regulator (see Use &
Care section). Once cylinder has been filled and leak checked, place cylinder into hole in bottom shelf. Make sure cylinder
valve is facing front of grill. Secure cylinder with cylinder screw under bottom shelf. Insert regulator through large hole in
right side panel. See Use & Care section of this manual to perform the “Burner Flame Check” and for
important safety instructions before using.
CAUTION
Cylinder valve must face to front of cart once
tank is attached. Failure to install cylinder
correctly may allow gas hose to be damaged
in operation, resulting in the risk of fire.
Cylinder screw at rear of cart
Always keep LP cylinders in upright position during use,
transport, and storage.
Regulator
31
EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.
EMERGENCIES:
If a gas
leak cannot
due to gas leakage, call the fire department.
Prevention/Solution
Emergencies
Possible
Cause be stopped, or a fire occurs
Gas leaking from
cracked/cut/burned
hose.
•Damaged hose.
•Turn off gas at LP cylinder or at source on natural gas systems. If
anything but burned, replace valve/hose/regulator. If burned,
discontinue use of product until a plumber has investigated cause
and corrections are made.
Gas leaking from LP
cylinder.
•Mechanical failure due to rusting or
mishandling.
•Replace LP cylinder.
Gas leaking from LP
cylinder valve.
• Failure of cylinder valve from
mishandling or mechanical failure.
• Turn off LP cylinder valve. Return LP cylinder to gas supplier.
Gas leaking between
LP cylinder and
regulator connection.
•Improper installation, connection not
tight, failure of rubber seal.
•Turn off LP cylinder valve. Remove regulator from cylinder and
visually inspect rubber seal for damage. See LP Cylinder Leak Test
and Connecting Regulator to the LP Cylinder.
Fire coming through
control panel.
• Fire in burner tube section of burner due
to blockage.
•Turn off control knobs and LP cylinder valve. Leave lid open to
allow flames to die down. After fire is out and grill is cold, remove
burner and inspect for spider nests or rust. See Natural Hazard
and Cleaning the Burner Assembly pages.
Grease fire or
continuous excessive
flames above cooking
surface.
• Too much grease buildup in burner area.
• Turn off control knobs and LP cylinder valve. Leave lid open to
allow flames to die down. After cooling, clean food particles and
excess grease from inside firebox area, grease tray, and other
surfaces.
Possible Cause
Prevention/Solution
GAS ISSUES:
• Trying to light wrong burner.
• See instructions on control panel and in Use and Care section.
• Burner not engaged with control valve.
• Make sure valves are positioned inside of burner tubes.
• Obstruction in burner.
• Ensure burner tubes are not obstructed with spider webs or other
matter. See cleaning section of Use and Care.
• No gas flow.
• For a grill equipped with the AUTO-CLEAN™ feature, make sure
the AUTO-CLEAN™ valve is set to “Grill”
• Make sure LP cylinder is not empty. If LP cylinder is not empty,
refer to “Sudden drop in gas flow.”
• Vapor lock at coupling nut to LP cylinder.
• Turn off knobs and disconnect coupling nut from LP cylinder.
Reconnect and retry.
• Turn the coupling nut approximately one-half to three-quarters
additional turn until solid stop. Tighten by hand only - do not use
tools.
• Replace electrode(s).
Troubleshooting
Problem
Burner(s) will not light
using ignitor.
(See Electronic Ignition
Troubleshooting also)
Continued on next
page.
• Coupling nut and LP cylinder valve not
fully connected.
ELECTRICAL ISSUES:
•Electrode cracked or broken; “sparks at
crack.”
32
•Electrode tip not in proper position.
Main Burners:
• Tip of electrode should be pointing toward gas port opening on
burner. The distance should be 1/8” to 1/4”. Adjust if necessary.
Sideburner:
• Tip of electrode should be pointing toward gas port opening on
burner. the distance should be 1/8” to 3/16”. Adjust if necessary.
•Wire and/or electrode covered with
cooking residue.
•Clean wire and/or electrode with rubbing alcohol and clean swab.
•Wires are loose or disconnected.
•Reconnect wires or replace electrode/wire assembly.
•Wires are shorting (sparking) between
ignitor and electrode.
•Replace ignitor wire/electrode assembly.
•Dead battery.
•Replace with a new AA-size alkaline battery.
Troubleshooting (continued)
Problem
Possible Cause
Prevention/Solution
Burner(s) will not light
using ignitor.
•Faulty electronic ignition circuit.
•See Troubleshooting Integrated Electronic Ignition section.
•Sparking somewhere other than
between burner and electrode.
•Inspect wire insulation and proper connections. Replace wires if
insulation is broken.
Burner(s) will not
match light.
•See “GAS ISSUES:” on previous page.
•Improper method of match-lighting.
•See “Match-Lighting” section of Use and Care.
•Out of gas.
•Check for gas in LP tank.
•Excess flow valve tripped.
•Turn off knobs, wait 30 seconds and light grill. If flames are still low,
turn off knobs and LP tank valve. Disconnect regulator. Reconnect
regulator and leak-test. Turn on LP tank valve, wait 30 seconds and
then light grill.
•Vapor lock at coupling nut/LP tank
connection.
•Turn off knobs and LP tank valve. Disconnect coupling nut from
tank. Reconnect and retry.
•High or gusting winds.
•Turn front of grill to face wind or increase flame height.
•Low on LP gas.
•Refill LP tank.
•Excess flow valve tripped.
•Refer to “Sudden drop in gas flow” above.
•Grease buildup.
•Clean burners and inside of grill/firebox.
•Excessive fat in meat.
•Trim fat from meat before grilling.
•Excessive cooking temperature.
•Adjust (lower) temperature accordingly.
Persistent grease fire.
•Grease trapped by food buildup around
burner system.
•Turn knobs to OFF. Turn gas off at LP tank. Leave lid in position and
let fire burn out. After grill cools, remove and clean all parts.
Flashback...
(fire in burner tube(s)).
•Burner and/or burner tubes are blocked.
•Turn knobs to OFF. Clean burner and/or burner tubes. See burner
cleaning section of Use and Care manual.
Unable to fill LP tank.
•Some dealers have older fill nozzles
with worn threads.
•The worn nozzles don’t have enough “bite” to engage the valve. Try
a second LP dealer.
One burner does not
light from other
burner(s).
•Grease buildup or food particles in
end(s) of carryover tube(s).
•Clean carry-over tube(s) with wire brush.
AUTO-CLEAN™
Possible Cause
Prevention/Solution
Sudden drop in gas
flow or low flame.
Flames blow out.
Flare-up.
(If Equipped)
Timer does not work
(Green light does not
flash)
Ÿ
Dead Battery
Ÿ
Batteries installed incorrectly.
Ÿ
Knob Position did not start the Clean
Cycle
Ÿ
Replace Batteries
Ÿ
Install batteries correctly.
Ÿ
Push Knob in to start the clean cycle. (Green LED should begin to
flash)
No LED’s will illuminate
Ÿ
Dead Battery
Ÿ
Replace Batteries
Red LED next to battery
symbol is illuminated
Ÿ
Low Battery Strength
Ÿ
Prepare to replace batteries (NOTE: Clean cycle will operate with
a weak battery.
33
Troubleshooting - Integrated Electronic Ignition
Problem (Ignition)
SECTION I
No sparks appear at
any electrodes when
burner control knobs
are turned to ; no
noise can be heard
from spark module.
SECTION II
No sparks appear at
any electrodes when
burner control knobs
are turned to ; noise
can be heard from
spark module.
SECTION III
Sparks are present
but not at all
electrodes and/or not
at full strength
34
Possible Cause
Check Procedure
Prevention/Solution
•Battery not installed
properly.
•Check battery orientation.
•Install battery (make sure that “+” and “–”
connectors are oriented correctly, with “+” end up
and “–” end down.)
•Dead battery.
•Has battery been used
previously?
•Replace battery with new AA-size alkaline battery.
•Battery cap not
installed properly.
•Check to ensure battery cap
is fully engaged.
•Remove battery cap and reinstall, making sure it
can be fully engaged.
•Faulty spark module.
•If no sparks are generated
with new battery and good
wire connections, module is
faulty.
•Replace spark module assembly.
•Output lead
connections not
connected.
•Are output connections on
and tight?
•Remove and reconnect all output connections at
module and electrodes.
•Electrode tip not in
proper position.
•Are the electrode tips
pointing in the right
direction? Is the gap too big?
Main Burners:
•Tip of electrode should be pointing toward port hole
in burner. The distance should be 1/8” to 3/16”.
Adjust if necessary.
Sideburner:
•Tip of electrode should be pointing toward gas port
opening on burner. The distance should be 1/8” to
3/16”. Adjust if necessary.
•Output lead
connections not
connected.
•Are output connections on
and tight?
•Remove and reconnect all output connections at
module and electrodes.
•Arcing to grill away
from burner(s).
•If possible, observe grill in
dark location. Operate
ignition system and look for
arcing between output wires
and grill frame.
•If sparks are observed other than from burner(s),
wire insulation may be damaged. Replace wires.
•Weak battery.
•All sparks present but weak
or at slow rate.
•Replace battery with a new AA-size alkaline battery.
•Electrodes are wet.
•Has moisture accumulated
on electrode and/or in burner
ports?
•Use paper towel to remove moisture.
•Electrodes cracked or
broken “sparks at
crack”.
•Inspect electrodes for
cracks.
•Replace cracked or broken electrodes.
Warranty Registration Department
P.O. Box 1240
Columbus, GA 31902-1240
35
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising