Alto-Shaam | COMBITOUCH SERIES 20o20ESG | Specifications | Alto-Shaam COMBITOUCH SERIES 20o20ESG Specifications

Alto-Shaam COMBITOUCH SERIES 20o20ESG Specifications
Combination
Oven / Steamer
ES GAS
SERIES
6•10ESG
10•10ESG
7•14ESG
10•20ESG
12•18ESG
20•20ESG
I N STALLATION
W 1 6 4 N 9 2 2 1 Wa t e r S t r e e t • P. O . Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA
PHONE: 262.251.3800 • 800.558.8744 USA/CANADA
FAX: 262.251.7067 • 800.329.8744 U.S.A. ONLY
WEBSITE: www.alto-shaam.com
PRINTED IN U.S.A.
#MN-28898 • 03/09
General Information
Delivery / Unpacking . . . . . . . . . . . . . . . . . .1.
Safety Procedures and Precautions . . . . . . . . .2.
Specifications
Options . . . . . . . . . . . . . . . . . . . . . . . . . . .3.
6•10esG . . . . . . . . . . . . . . . . . . . . . . . . . . .4.
10•10esG . . . . . . . . . . . . . . . . . . . . . . . . . .5.
7•14esG . . . . . . . . . . . . . . . . . . . . . . . . . . .6.
10•20esG . . . . . . . . . . . . . . . . . . . . . . . . . .7.
12•18esG . . . . . . . . . . . . . . . . . . . . . . . . . .8.
20•20esG . . . . . . . . . . . . . . . . . . . . . . . . . .9.
Installation Requirements
Installation Codes & Standards . . . . . . . . . . .10.
Ventilation General Requirements . . . . . . . . .11.
Positioning on Site . . . . . . . . . . . . . . . . . . .11.
Minimum Clearance Requirements
Positioning Requirements
. . . . . . . .11.
. . . . . . . . . . . . . .12.
Ventilation Specific Requirements . . . . . . . . .13.
Electrical Requirements . . . . . . . . . . . . . . . .14.
Drip Tray Installation . . . . . . . . . . . . . . . . .15.
Mobile Equipment Restraint . . . . . . . . . . . . .15.
Gas Supply Specifications . . . . . . . . . . . . . .16.
Gas Pressures . . . . . . . . . . . . . . . . . . . . . .16.
Gas Connection . . . . . . . . . . . . . . . . . . . . .17.
Gas Leak Testing . . . . . . . . . . . . . . . . . . . .19.
Gas Exhaust
. . . . . . . . . . . . . . . . . . . . . . .19.
Water Quality Requirements . . . . . . . . . . . . .20.
Water Connection
. . . . . . . . . . . . . . . . . . .21.
Water Filtration System . . . . . . . . . . . . . . . .22.
Water Drainage . . . . . . . . . . . . . . . . . . . . .23.
Installation Checklist . . . . . . . . . . . . . . . . .24.
Error Codes
Control Reset
Error Codes
. . . . . . . . . . . . . . . . . . . . . .25.
. . . . . . . . . . . . . . . . . . . . . . .25.
Emergency Operation . . . . . . . . . . . . . . . . .28.
Equipment Limited Warranty
. . . . . . . . . . .29.
Transportation Damage and Claims . . . . . .30.
®
DELIVERY
U N PA C K I N G
This Alto-Shaam appliance has been
thoroughly tested and inspected to insure only the
highest quality unit is provided. Upon receipt,
check for any possible shipping damage and report
it at once to the delivering carrier. See
Transportation Damage and Claims section
located in this manual.
This appliance, complete with unattached
items and accessories, may have been delivered in
one or more packages. Check to ensure that all
standard items and options have been received
with each model as ordered.
Save all the information and instructions
packed with the appliance. Complete and return
the warranty card to the factory as soon as
possible to assure prompt service in the event of a
warranty parts and labor claim.
This manual must be read and understood by
all people using or installing the equipment
model. Contact the Alto-Shaam service
department if you have any questions concerning
installation, operation, or maintenance.
NOTE: All claims for warranty must include the
full model number and serial number of
the unit.
1. Carefully remove the
appliance from the
carton or crate.
NOTE: Do not discard the
carton and other
packaging material
until you have
inspected the unit
for hidden damage
and tested it for
proper operation.
®
®
2. Read all instructions in this manual carefully
before initiating the installation of this appliance.
DO NOT DISCARD THIS MANUAL.
This manual is considered to be part of the
appliance and is to be provided to the owner or
manager of the business or to the person
responsible for training operators. Additional
manuals are available from the Alto-Shaam
service department.
3. Remove all protective plastic film, packaging
materials, and accessories from the appliance
before connecting electrical power. Store any
accessories in a convenient place for future use.
CAUTION
TO PREVENT PERSONAL INJURY,
USE CAUTION WHEN MOVING OR
LEVELING THIS APPLIANCE.
THE INFORMATION CONTAINED IN THIS
LES INFORMATIONS CONTENUES DANS CE
MANUAL IS IMPORTANT FOR THE PROPER
MANUEL SONT IMPORTANTES POUR
INSTALLATION OF THIS OVEN .
L’ INSTALLATION L’ UTILISATION ET
PLEASE
L’ ENTRETIEND DE CE FOUR .
READ CAREFULLY AND RETAIN FOR
FUTURE REFERENCE .
S ’ IL VOUS
PLAIT LISEZ - LE TRES ATTENTIVEMENT ET
CONSERVEZ - LE .
IMPROPER CONNECTION OF THIS APPLIANCE
WILL NULLIFY ALL WARRANTIES .
LA NON - APPLICATION DE CES CONSIGNES
ANNULE TOUTES GARANTIES .
GAS COMBITHERM
—
I N S TA L L AT I O N M A N U A L
#MN-28898
PG.
1
SAFETY PROCEDURES
AND PRECAUTIONS
Knowledge of proper procedures is essential to the
safe operation of electrically and/or gas energized
equipment. In accordance with generally accepted
product safety labeling guidelines for potential
hazards, the following signal words and symbols
may be used throughout this manual.
DANGER
Used to indicate the presence of a
hazard that WILL cause severe
personal injury, death, or substantial
property damage if the warning
included with this symbol is ignored.
1. This appliance is intended to cook, hold or
process foods for the purpose of human
consumption. No other use for this appliance is
authorized or recommended.
2. This appliance is intended for use in commercial
establishments where all operators are familiar
with the purpose, limitations, and associated
hazards of this appliance. Operating
instructions and warnings must be read and
understood by all operators and users.
3. Any troubleshooting guides, component views,
and parts lists included in this manual are for
general reference only and are intended for use
by qualified technical personnel.
WA R N I N G
Used to indicate the presence of a
hazard that CAN cause personal injury,
possible death, or major property
damage if the warning included with
this symbol is ignored.
4. This manual should be considered a permanent
part of this appliance. This manual and all
supplied instructions, diagrams, schematics,
parts lists, notices, and labels must remain with
the appliance if the item is sold or moved to
another location.
CAUTION
Used to indicate the presence of a
hazard that can or will cause minor or
moderate personal injury or property
damage if the warning included with
this symbol is ignored.
CAUTION
Used to indicate the presence of a hazard that can
or will cause minor personal injury, property
damage, or a potential unsafe practice if the
warning included with this symbol is ignored.
CAUTION
N O T E : Used to notify personnel of
WHEN WELDING ANY STAINLESS
STEEL COMPONENTS ON THIS
APPLIANCE, THE ELECTRONIC
CONTROL BOARDS MUST BE
ISOLATED FROM THE APPLIANCE.
installation, operation, or
maintenance information that is
important but not hazard related.
GAS COMBITHERM
PG.
2
—
I N S TA L L AT I O N M A N U A L
#MN-28898
C O M M O N S P E C I F I C AT I O N S
®
COMBITHERM
■ COMBIGUARD™ TRIPLE-GUARD WATER
FILTRATION SYSTEM
( INCLUDES 1
CARTRIDGE )
FI-23014
■ COMBIGUARD ™ REPLACEMENT FILTER
■ FRY BASKET, 12"
X
■ GRILLING GRATE,
12"
X
FI-26356
20" (325mm x 530mm)
BS-26730
20" (325mm x 530mm)
SH-26731
■ COMBITHERM CLEANING LIQUID —
SPECIALLY FORMULATED FOR COMBITHERM OVENS
TWELVE
(12)
CONTAINERS / CASE ,
1
QUART
■ COMBITHERM CLEANING TABS —
➥
(C. 1
CE-24750
➥
TWO
(2)
CONTAINERS / BOX ,
90
■ SCALE FREE ™
( CITRUS
CE-28892
CASE
=
FOUR
4- LB
BOTTLES ;
4- LB
BOTTLE MAKES
■ Computer Software Options
N ot available on S-Control Mod e ls .
REFER TO HACCP SPECIFICATION SHEET
FOR APPLICABLE PART NUMBERS
SH-23000
CR-33543
10
CE-27889
GALLONS
Ten (10) Chicken Roasting Rack
SPECIFY AS REQUIRED
AVAILABLE THROUGH AN ALTO - SHAAM FASTEAM CENTER
■ HACCP Documentation
NOT INCLUDED )
PACKETS EACH CONTAINER
BASED , NON - CORROSIVE DELIMING PRODUCT )
■ SERVICE START-UP CHECK
( PAN
LITER ) EACH
SPECIALLY FORMULATED FOR COMBITHERM OVENS
■ QUICK DISCONNECT KIT
Six (6) Chicken Roasting Rack
SH-22634
5005676
#9015
■ HACCP Documentation with Kitchen Management
Fry Basket BS-26730
■ Wireless HACCP Documentation with
Kitchen Management
IEEE 802.11b STANDARDS
Grilling Grate SH-26731
GAS COMBITHERM
—
I N S TA L L AT I O N M A N U A L
#MN-28898
PG.
3
6 • 1 0 E S G S P E C I F I C AT I O N S
®
2-3/8" (60mm)
COMBITHERM
Electrical
Connection (Bottom)
2" (50mm)
25"
(635mm)
CLEARANCE REQUIREMENTS
LEFT : 6" (152mm) PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
20" (508mm) F R O M H E AT P R O D U C I N G E Q U I P M E N T
TOP : 20" (508mm) FOR AIR MOVEMENT
RIGHT : 4" (102mm)
BOTTOM : 5-1/8" (130mm) FOR LEGS
BACK : 4" (102mm)
COUNTER - TOP INSTALLATIONS MUST MAINTAIN 4" (102mm)
MINIMUM CLEARANCE FROM THE COUNTER SURFACE .
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level. Hood installation. Water supply
shut-off valve and back-flow preventer. Alternate burner orifice
is required for installation sites at elevations of 3,000 feet (914m)
above sea level.
VOLTAGE
CYCLE/HZ
PHASE
110 - 120
1
OTHER VOLTAGES AVAILABLE :
SHIP
CRATE
377 lb
442 lb
EST .
EST .
40"
X
(200 kg)
X
40"
21-11/16"
(550mm)
EST .
EST .
EST .
5" (125mm)
34" (863mm)
MAXIMUM CONNECTED
GAS TYPE MUST BE SPECIFIED ON ORDER .
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure
that incoming water supply is compliant with the specifications
listed through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
6•10ESG
FULL-SIZE PANS: 20" x 12" x 2-1/2"
GN 1/1: 530 x 325 x 65mm
HALF-SIZE SHEET PANS:* 18" x 13" x 1"
ON WIRE SHELVES ONLY
(1016 x 1143 x 1016mm)
72 lb (33 kg)
45
VOLUME MAXIMUM :
—
45,000 Btu/hr
3/4" NPT
PRESSURE : 5.5" W.C. (Natural Gas)
9" W.C. (Propane)
PRESSURE : 14" W.C.
HOOK - UP :
MINIMUM CONNECTED
2 Wire plus ground, AWG 12
GAS COMBITHERM
4
5-1/2"
(140mm)
Water Drain
(Bottom)
CONNECTED ENERGY LOAD :
Range 200 — 415V — 1 or 3 ph, 50 or 60 Hz
(171 kg)
45"
34-5/16"
(871mm)
GAS REQUIREMENTS
C A PA C I T Y
DIMENSIONS :
PG.
7-1/2"
(191mm)
AWG
50/60
WEIGHT
NET
37" (939mm)
DIMENSIONS: H x W x D
EXTERIOR :
34" x 42-1/16" x 37" (863mm x 1068mm x 939mm)
EXTERIOR WITH RETRACTABLE DOOR :
34" x 46-1/16" x 37" (863mm x 1170mm x 939mm)
INTERIOR :
17-3/4" x 17-3/8" x 26-13/16" (450mm x 440mm x 680mm)
47-5/16" (1201mm)
ELECTRICAL
27-3/4"
(704mm)
Steam
Vent
(Top)
Untreated Water Intake (Bottom)
Gas Connection
(Bottom)
40-1/8"
(1018mm)
58-3/16" (1478mm)
19-3/8"
(492mm)
10-5/8"
(270mm)
Treated Water Intake (Bottom)
42-1/16" (1068mm)
15-5/8"
(396mm)
Water Drain
(Side Back)
6-1/4" (159mm)
5-1/2" (140mm)
3-5/8"
(92mm)
3-1/16"
(76mm)
11-1/2" (292mm)
I N S TA L L AT I O N M A N U A L
#MN-28898
kW
AMPS
5.7
0.68
Six (6)
Six (6)
Six (6)
MAXIMUM
QUARTS
(57
LITERS )
6•10ESG/sk
kW
AMPS
9.5
1.14
Four (4)
Four (4)
Five (5)
1 0 • 1 0 E S G S P E C I F I C AT I O N S
®
2" (50mm)
47-5/16" (1201mm)
25"
(635mm)
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level. Hood installation. Water supply
shut-off valve and back-flow preventer. Alternate burner orifice
is required for installation sites at elevations of 3,000 feet (914m)
above sea level.
VOLTAGE
110 - 120
1
OTHER VOLTAGES AVAILABLE :
SHIP
CRATE
CONNECTED ENERGY LOAD :
MINIMUM CONNECTED
MAXIMUM CONNECTED
530 lb
DIMENSIONS :
EST .
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure
that incoming water supply is compliant with the specifications
listed through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
2 Wire plus ground, AWG 12
Range 200 — 415V — 1 or 3 ph, 50 or 60 Hz
EST .
50"
X
(222 kg)
(240 kg)
45"
X
40"
EST .
EST .
EST .
(1270 x 1143 x 1016mm)
68,000 Btu/hr
3/4" NPT
PRESSURE : 5.5" W.C. (Natural Gas)
9" W.C. (Propane)
PRESSURE : 14" W.C.
HOOK - UP :
GAS TYPE MUST BE SPECIFIED ON ORDER .
C A PA C I T Y
490 lb
21-11/16"
(550mm)
GAS REQUIREMENTS
AWG
50/60
WEIGHT
Water Drain
(Bottom)
5-1/2"
(140mm)
7-1/2"
(191mm)
10•10ESG
CYCLE/HZ
PHASE
34-5/16"
(871mm)
DIMENSIONS: H x W x D
EXTERIOR :
43-5/8" x 42-1/16" x 37" (1108mm x 1068mm x 939mm)
EXTERIOR WITH RETRACTABLE DOOR :
43-5/8" x 46-1/16" x 37" (1108mm x 1170mm x 939mm)
INTERIOR :
27-3/8" x 17-3/8" x 26-13/16" (695mm x 440mm x 680mm)
CLEARANCE REQUIREMENTS
LEFT : 6" (152mm) PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
20" (508mm) F R O M H E AT P R O D U C I N G E Q U I P M E N T
RIGHT : 4" (102mm)
TOP : 20" (508mm) FOR AIR MOVEMENT
BOTTOM : 5-1/8" (130mm) FOR LEGS
BACK : 4" (102mm)
COUNTER - TOP INSTALLATIONS MUST MAINTAIN 4" (102mm)
MINIMUM CLEARANCE FROM THE COUNTER SURFACE .
ELECTRICAL
37" (939mm)
5" (125mm)
58-3/16" (1478mm)
Electrical
Connection (Bottom)
37-3/8" (949mm)
10-5/8"
(270mm)
19-3/8"
(492mm)
Steam
Vent
(Top)
Untreated Water
Intake (Bottom)
Gas Connection
(Bottom)
40-1/8"
(1018mm)
15-5/8"
(396mm)
Water Drain
(Side Back)
6-1/4" (159mm)
5-1/2" (140mm)
3-5/8"
(92mm)
43-5/8" (1108mm)
2-3/8" (60mm)
42-1/16" (1068mm)
11-1/2" (292mm)
Treated Water Intake (Bottom)
NET
3-1/16"
(76mm)
COMBITHERM
FULL-SIZE PANS: 20" x 12" x 2-1/2"
GN 1/1: 530 x 325 x 65mm
HALF-SIZE SHEET PANS:* 18" x 13" x 1"
ON WIRE SHELVES ONLY
* ADDITIONAL
kW
AMPS
5.7
.68
Ten (10)
Ten (10)
Ten (10)
120 lb (54 kg) MAXIMUM
75 QUARTS (95
VOLUME MAXIMUM :
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
GAS COMBITHERM
—
I N S TA L L AT I O N M A N U A L
10•10ESG/sk
AMPS
9.5
kW
1.14
Eight (8)
Eight (8)
Nine (9)
LITERS )
#MN-28898
PG.
5
7 • 1 4 E S G S P E C I F I C AT I O N S
®
COMBITHERM
44-7/16" (1128mm)
27-9/16"
(700mm)
41-3/4" (1060mm)
49-13/16" (1265mm)
Water Drain
(Side Back)
2" (50mm)
73-7/16" (1865mm)
Gas Connection
(Bottom)
30-1/16"
(763mm)
Electrical
Connection (Bottom)
Steam Vent (Top)
Untreated Water Intake (Bottom)
Treated Water Intake (Bottom)
31-3/4"
(805mm)
33-1/8"
(840mm)
4-5/8" (116mm)
CLEARANCE REQUIREMENTS
LEFT : 6" (152mm) PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
20" (508mm) F R O M H E AT P R O D U C I N G E Q U I P M E N T
TOP : 20" (508mm) FOR AIR MOVEMENT
RIGHT : 4" (102mm)
BOTTOM : 5-1/8" (130mm) FOR LEGS
BACK : 4" (102mm)
COUNTER - TOP INSTALLATIONS MUST MAINTAIN 4" (102mm)
MINIMUM CLEARANCE FROM THE COUNTER SURFACE .
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level. Hood installation. Water supply
shut-off valve and back-flow preventer. Alternate burner orifice
is required for installation sites at elevations of 3,000 feet (914m)
above sea level.
VOLTAGE
CYCLE/HZ
PHASE
110 - 120
1
OTHER VOLTAGES AVAILABLE :
NET
SHIP
CRATE
DIMENSIONS :
6
CONNECTED ENERGY LOAD :
MINIMUM CONNECTED
MAXIMUM CONNECTED
48"
X
56"
X
50"
EST .
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure
that incoming water supply is compliant with the specifications
listed through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
7•14ESG
(1219 x 1422 x 1473mm)
FULL-SIZE PANS: 20" x 12" x 2-1/2"
GN 1/1: 530 x 325 x 65mm
GN 2/1: 650 x 530 x 65mm
FULL-SIZE SHEET PANS:* 18" x 26" x 1"
ON WIRE SHELVES ONLY
* ADDITIONAL
HOOK - UP :
GAS TYPE MUST BE SPECIFIED ON ORDER .
C A PA C I T Y
NOT YET AVAILABLE
91,000 Btu/hr
3/4" NPT
PRESSURE : 5.5" W.C. (Natural Gas)
9" W.C. (Propane)
PRESSURE : 14" W.C.
GAS REQUIREMENTS
2 Wire plus ground, AWG 12
AMPS
5.7
168 lb (76 kg) MAXIMUM
105 QUARTS (133
VOLUME MAXIMUM :
—
I N S TA L L AT I O N M A N U A L
#MN-28898
kW
0.68
Fourteen (14)
Fourteen (14)
Seven (7)
Seven (7)
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
GAS COMBITHERM
PG.
7-3/16"
(181mm)
Range 200 — 415V — 1 or 3 ph, 50 or 60 Hz
NOT YET AVAILABLE
25-5/8"
(650mm)
8-1/2" (216mm)
9/16"
(13mm)
7-9/16"
(192mm)
AWG
50/60
WEIGHT
Water Drain
(Bottom)
DIMENSIONS: H x W x D
EXTERIOR :
42" x 49-13/16" x 44-7/16" (1066mm x 1265mm x 1128mm)
EXTERIOR WITH RETRACTABLE DOOR :
42" x 53-13/16" x 44-7/16" (1066mm x 1367mm x 1128mm)
INTERIOR :
23-5/8" x 25-1/4" x 33-7/8" (600mm x 640mm x 860mm)
55-1/16" (1398mm)
ELECTRICAL
22-11/16"
(575mm)
12-13/16"
(325mm)
47-7/8" (1215mm)
42" (1066mm)
4-13/16"
(121mm)
6”
(151mm)
17-3/8"
(441mm)
19-3/8"
(491mm)
26-3/4"
(678mm)
3-9/16"
(89mm)
37-5/8” (954mm)
4-3/8" (110mm)
LITERS )
7•14ESG/sk
AMPS
9.5
kW
1.14
Twelve (12)
Twelve (12)
Five (5)
Six (6)
1 0 • 2 0 E S G S P E C I F I C AT I O N S
®
COMBITHERM
20-5/16"
(515mm)
Water Drain
(Side Back)
42-9/16"
(1080mm)
49-13/16" (1265mm)
12-13/16"
(325mm)
47-7/8" (1215mm)
4-5/8" (116mm)
44" (1118mm)
RIGHT :
BACK :
4" (102mm)
F R O M H E AT P R O D U C I N G E Q U I P M E N T
4" (102mm)
BOTTOM :
20" (508mm)
FOR AIR MOVEMENT
5-1/8" (130mm)
FOR LEGS
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level. Hood installation. Water supply
shut-off valve and back-flow preventer. Alternate burner orifice
is required for installation sites at elevations of 3,000 feet (914m)
above sea level.
VOLTAGE
CYCLE/HZ
PHASE
110 - 120
1
OTHER VOLTAGES AVAILABLE :
WEIGHT
NET
SHIP
CRATE
573 lb
875 lb
DIMENSIONS :
EST .
EST .
59"
X
(260 kg)
(397 kg)
55"
X
48"
EST .
EST .
EST .
(1499 x 1397 x 1219mm)
MINIMUM CONNECTED
MAXIMUM CONNECTED
GAS TYPE MUST BE SPECIFIED ON ORDER .
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure
that incoming water supply is compliant with the specifications
listed through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
AWG
50/60
2 Wire plus ground, AWG 12
ON WIRE SHELVES ONLY
7.8
20" x 12" x 2-1/2"
530 x 325 x 65mm
650 x 530 x 65mm
18" x 26" x 1"
240 lb (109 kg) MAXIMUM
150 QUARTS (190
VOLUME MAXIMUM :
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
GAS COMBITHERM
kW
AMPS
.936
Range 200 — 415V — 1 or 3 ph, 50 or 60 Hz
C A PA C I T Y
FULL-SIZE PANS:
GN 1/1:
GN 2/1:
FULL-SIZE SHEET PANS:*
* ADDITIONAL
HOOK - UP :
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
ELECTRICAL
105,000 Btu/hr
3/4" NPT
PRESSURE : 5.5" W.C. (Natural Gas)
9" W.C. (Propane)
PRESSURE : 14" W.C.
GAS REQUIREMENTS
PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
TOP :
2" (50mm)
CONNECTED ENERGY LOAD :
CLEARANCE REQUIREMENTS
20" (508mm)
30-1/2"
(775mm)
2-3/16" (56mm)
DIMENSIONS: H x W x D
EXTERIOR :
52-11/16" x 49-13/16" x 45-3/16" (1337mm x 1265mm x 1148mm)
EXTERIOR WITH RETRACTABLE DOOR :
52-11/16" x 53-13/16" x 45-3/16" (1337mm x 1367mm x 1148mm)
INTERIOR :
33-7/8" x 25-1/4" x 33-7/8" (860mm x 640mm x 860mm)
55-7/16"
(1407mm)
6" (152mm)
22-11/16"
(575mm)
Water Drain
(Bottom)
31-3/4"
(805mm)
2" (50mm)
LEFT :
6-1/4" (157mm)
Treated Water
Intake (Bottom)
Gas Connection
(Bottom)
8-15/16" (226mm)
73-13/16" (1875mm)
Steam Vent
(Top)
Untreated Water
Intake (Bottom)
43-13/16" (1111mm)
Electrical Connection (Bottom)
52-11/16" (1337mm)
4-3/8" (110mm)
3-9/16"
(89mm)
17-3/8"
(441mm)
19-3/8"
(491mm)
26-3/4"
(678mm)
6" (151mm)
45-3/16"
(1148mm)
—
I N S TA L L AT I O N M A N U A L
Twenty (20)
Twenty (20)
Ten (10)
Ten (10)
LITERS )
#MN-28898
PG.
7
1 2 • 1 8 E S G S P E C I F I C AT I O N S
®
COMBITHERM
20-5/16"
(515mm)
Water Drain
(Side Back)
4-5/8" (116mm)
33-1/8"
(840mm)
BACK :
4" (102mm)
F R O M H E AT P R O D U C I N G E Q U I P M E N T
4" (102mm)
BOTTOM :
20" (508mm)
FOR AIR MOVEMENT
5-1/8" (130mm)
FOR LEGS
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level. Hood installation. Water supply
shut-off valve and back-flow preventer. Alternate burner orifice
is required for installation sites at elevations of 3,000 feet (914m)
above sea level.
VOLTAGE
CYCLE/HZ
PHASE
110 - 120
1
OTHER VOLTAGES AVAILABLE :
WEIGHT
NET
SHIP
CRATE
666 lb
865 lb
DIMENSIONS :
EST .
EST .
56"
X
(302 kg)
(392 kg)
55"
X
50"
EST .
EST .
EST .
(1422 x 1397 x 1270mm)
8
MAXIMUM CONNECTED
GAS TYPE MUST BE SPECIFIED ON ORDER .
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure
that incoming water supply is compliant with the specifications
listed through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
2 Wire plus ground, AWG 12
ON WIRE SHELVES ONLY
* ADDITIONAL
kW
AMPS
7.8
.936
Range 200 — 415V — 1 or 3 ph, 50 or 60 Hz
C A PA C I T Y
FULL-SIZE PANS:
GN 1/1:
GN 2/1:
FULL-SIZE SHEET PANS:*
20" x 12" x 2-1/2"
530 x 325 x 65mm
650 x 530 x 65mm
18" x 26" x 1"
288 lb (131 kg) MAXIMUM
180 QUARTS (228
VOLUME MAXIMUM :
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
GAS COMBITHERM
PG.
MINIMUM CONNECTED
AWG
50/60
HOOK - UP :
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
ELECTRICAL
105,000 Btu/hr
3/4" NPT
PRESSURE : 5.5" W.C. (Natural Gas)
9" W.C. (Propane)
PRESSURE : 14" W.C.
GAS REQUIREMENTS
PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
TOP :
7-3/16"
(181mm)
CONNECTED ENERGY LOAD :
CLEARANCE REQUIREMENTS
RIGHT :
25-5/8"
(650mm)
8-1/2" (216mm)
DIMENSIONS: H x W x D
EXTERIOR :
51-1/16" x 49-13/16" x 45-3/16" (1296mm x 1265mm x 1148mm)
EXTERIOR WITH RETRACTABLE DOOR :
51-1/16" x 53-13/16" x 45-3/16" (1296mm x 1367mm x 1148mm)
INTERIOR :
33-7/8" x 25-1/4" x 33-7/8" (860mm x 640mm x 860mm)
55-7/16"
(1407mm)
20" (508mm)
Water Drain
(Bottom)
31-3/4"
(805mm)
2" (50mm)
6" (152mm)
4-1/2" (114mm)
7-5/16" (184mm)
73-13/16" (1875mm)
Untreated Water
Intake (Bottom)
Treated Water
Intake (Bottom)
43-13/16" (1111mm)
Steam Vent
(Top)
22-11/16"
(575mm)
12-13/16"
(325mm)
47-7/8" (1215mm)
Electrical Connection (Bottom)
Gas Connection
(Bottom)
LEFT :
42-9/16"
(1080mm)
49-13/16" (1265mm)
51-1/16" (1296mm)
4-3/8" (110mm)
3-9/16"
(89mm)
17-3/8"
(441mm)
19-3/8"
(491mm)
26-3/4"
(678mm)
6" (151mm)
45-3/16"
(1148mm)
—
I N S TA L L AT I O N M A N U A L
#MN-28898
Twenty-four (24)
Twenty-four (24)
Twelve (12)
Twelve (12)
LITERS )
2 0 • 2 0 E S G S P E C I F I C AT I O N S
®
20-1/4"
(514mm)
Water Drain
(Side Back)
45-3/16" (1148mm)
47-13/16" (1214mm)
42-9/16" (1080mm)
4-5/8" (116mm)
2" (50mm)
7-11/16" (195mm)
Treated Water
Intake (Bottom)
76-5/8" (1946mm)
73-13/16" (1874mm)
Untreated Water
Intake (Bottom)
75-1/4" (1911mm)
Steam
Vents
(Top)
Electrical Connection
(Bottom)
Gas Exhaust (Top)
Gas Connection
(Bottom)
49-13/16" (1264mm)
8-15/16" (226mm)
4-3/8" (110mm)
3-9/16"
(89mm)
17-3/8"
(441mm)
19-3/8"
(491mm)
26-3/4"
(678mm)
6" (151mm)
COMBITHERM
55-7/16"
(1407mm)
44" (1118mm)
2" (49mm)
Water Drain
(Bottom)
30-1/2"
(775mm)
2-3/16"
(56mm)
DIMENSIONS: H x W x D
EXTERIOR :
76-5/8" x 49-13/16" x 45-3/16" (1946mm x 1264mm x 1148mm)
EXTERIOR WITH RETRACTABLE DOOR :
76-5/8" x 53-13/16" x 45-3/16" (1337mm x 1366mm x 1148mm)
INTERIOR :
54-15/16" x 25-1/4" x 33-7/8" (1395mm x 640mm x 860mm)
CONNECTED ENERGY LOAD :
CLEARANCE REQUIREMENTS
LEFT :
RIGHT :
BACK :
6" (152mm)
20" (508mm)
4" (102mm)
4" (102mm)
PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
F R O M H E AT P R O D U C I N G E Q U I P M E N T
TOP :
BOTTOM :
20" (508mm)
FOR AIR MOVEMENT
5-1/8" (130mm)
FOR LEGS
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level. Hood installation. Water supply
shut-off valve and back-flow preventer. Alternate burner orifice
is required for installation sites at elevations of 3,000 feet (914m)
above sea level.
VOLTAGE
110 - 120
WEIGHT
NET
SHIP
CRATE
PHASE
1
CYCLE/HZ
50/60
OTHER VOLTAGES AVAILABLE :
(2083 x 1422 x 1270mm)
* ADDITIONAL
MAXIMUM CONNECTED
GAS TYPE MUST BE SPECIFIED ON ORDER .
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure
that incoming water supply is compliant with the specifications
listed through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
AWG
2 Wire plus ground, AWG 10
22.0
20" x 12" x 2-1/2"
530 x 325 x 65mm
650 x 530 x 65mm
18" x 26" x 1"
480 lb (218 kg) MAXIMUM
300 QUARTS (380
VOLUME MAXIMUM :
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
GAS COMBITHERM
kW
AMPS
2.64
Range 200 — 415V — 1 or 3 ph, 50 or 60 Hz
C A PA C I T Y
FULL-SIZE PANS:
838 lb EST .
(380 kg) EST .
GN 1/1:
GN 2/1:
1325 lb EST . (601 kg) EST . FULL-SIZE SHEET PANS:*
ON WIRE SHELVES ONLY
82" X 56" X 50" EST .
DIMENSIONS :
MINIMUM CONNECTED
HOOK - UP :
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
ELECTRICAL
190,000 Btu/hr
3/4" NPT
PRESSURE : 5.5" W.C. (Natural Gas)
9" W.C. (Propane)
PRESSURE : 14" W.C.
GAS REQUIREMENTS
—
I N S TA L L AT I O N M A N U A L
Forty (40)
Forty (40)
Twenty (20)
Twenty (20)
LITERS )
#MN-28898
PG.
9
L O C AT I O N S I T E & I N S TA L L AT I O N R E Q U I R E M E N T S
®
COMBITHERM
DANGER
DANGER
IMPROPER INSTALLATION,
ALTERATION, ADJUSTMENT,
SERVICE, OR MAINTENANCE COULD
RESULT IN SEVERE INJURY, DEATH
OR CAUSE PROPERTY DAMAGE.
READ THE INSTALLATION,
OPERATING AND MAINTENANCE
INSTRUCTIONS THOROUGHLY
BEFORE INSTALLING OR SERVICING
THIS EQUIPMENT.
AVERTISSEMENT : UNE INSTALLATION,
UN AJUSTEMENT, UNE ALTÉRATION,
UN SERVICE OU UN ENTRETIEN NON
CONFORME AUX NORMES PEUT CAUSER
DES DOMMAGES À LA PROPRIÉTÉ, DES
BLESSURES OU LA MORT.
LIRE ATTENTIVEMENT LES DIRECTIVES
D’OPÉRATION ET D’ENTRETIEN AVANT
DE FAIRE L’INSTALLATION, OU
L’ENTRETIEN DE CET ÉQUIPEMENT.
®
THE OVEN MUST REMAIN ON
THE PALLET WHILE BEING
MOVED TO THE INSTALLATION
SITE BY FORK LIFT OR
PALLET LIFT TRUCK.
NOTE: Note dimensions required for doorways
and aisles for access of the oven and pallet
to the installation site. Transport the oven
in an upright and level position only. Do
not tilt the oven.
INSTALLATION CODES & STANDARDS
The following codes and standards are required for installation of this oven:
AIR SUPPLY, ELECTRICAL CONNECTIONS, WATER CONNECTIONS, GAS
CONNECTIONS, GAS EXHAUST, AND WASTE WATER DISCHARGE.
Installation must comply with local codes required for gas appliances. In the
absence of local codes, installation must comply with the National Fuel Gas Code,
ANSI Z223.1 (latest edition). In Canada, the appropriate code is the Natural Gas
Installation Code, CAN/CGA-B149.1 or the Propane Installation Code, CAN/CGA-B.
Adherence to code by a qualified installer is essential for the following: Gas
Plumbing, Gas Appliance Installation, Commercial Cooking Ventilation, Water and
Plumbing, and OSHA Regulations.
GAS COMBITHERM
PG.
10
—
I N S TA L L AT I O N M A N U A L
#MN-28898
®
L O C AT I O N S I T E & I N S TA L L AT I O N R E Q U I R E M E N T S
COMBITHERM
VENTILATION REQUIREMENTS
CAUTION
A steam ventilation hood is mandatory for the
operation of the oven. The ventilation hood must
be installed in accordance with local building
codes for the steam exhaust and must protrude
12-inches to 20-inches (300 to 500mm) over the
front side of the oven. A grease filter must be
located in the protruding area of the hood.
Grease filters should be thoroughly cleaned on a
regular basis following manufacturer's
instruction. Ventilation hoods must ensure an
adequate amount of incoming air during
operation and must be operated whenever the
combination oven/steamer is used in order to
avoid the accumulation of condensation in the
hood area. See the section titled Gas Exhaust.
POSITIONING ON SITE
Lift the oven from the pallet with a fork lift or
pallet lift truck positioned at the front of the oven.
For damage protection, the use of two wooden
boards, placed between the bottom of the oven
and the lifting forks, is strongly recommended.
To avoid damage, position the lift forks to the left
of the condenser and right of the right leg as
indicated in the diagram at right.
Stand the oven in a level position. Use the
adjustable feet to overcome an uneven floor and
ensure that the unit is level.
It is strongly recommended that table top models
be mounted on a factory supplied stand or a stand
that is stable, open, level, and non-combustible.
Recommended height is 23-inches (584mm).
Adjust the height of floor models for smooth
access of the trolley or cart. When positioning the
oven, observe the minimum space allocation
requirements shown.
To insure proper operation, the installation of this
oven must be completed by qualified technicians
in accordance with the instructions provided in
this manual. Failure to follow the instructions
provided may result in damage to the oven,
building, or cause personal injury to personnel.
GAS COMBITHERM
—
TO PREVENT PERSONAL INJURY,
USE CAUTION WHEN MOVING OR
LEVELING THIS APPLIANCE.
NOTE: To avoid equipment damage, observe
attention label on oven for area to avoid
with lifting fork.
MINIMUM CLEARANCE REQUIREMENTS
LEFT SIDE
6" (152mm)
MINIMUM
18" (457mm)
20" (508mm)
RIGHT SIDE
BACK
TOP
BOTTOM
4" (102mm)
SERVICE ACCESS RECOMMENDED
FROM HEAT PRODUCING EQUIPMENT
4" (102mm)
20" (508mm)
20" (508mm)
FOR AIR MOVEMENT
FOR AIR MOVEMENT
NOTE: Additional clearance is needed for service
access. A minimum distance of 18-inches is
strongly recommended. If adequate service
clearance is not provided, it will be necessary to
disconnect the gas, water, and drain to move the
oven with a fork lift for service access. Charges
in connection with inadequate service access is
not covered under warranty.
I N S TA L L AT I O N M A N U A L
#MN-28898
PG.
11
L O C AT I O N S I T E & I N S TA L L AT I O N R E Q U I R E M E N T S
®
COMBITHERM
POSITIONING REQUIREMENTS
❑ In order to ensure proper ventilation, a
minimum distance of at least 6-inches (152mm)
must be kept from the control panels side (left)
of the oven and any adjoining surfaces.
NOTE: Additional clearance is needed for
service access. A minimum distance of 18inches is strongly recommended. If adequate
service clearance is not provided, it will be
necessary to disconnect the gas, water, and drain
to move the oven with a fork lift for service
access. Charges in connection with inadequate
service access is not covered under warranty.
❑ Allow a minimum of 4-inches (102mm) from
the right side of the oven to allow the door to
open to at least a 90° angle. Fully opened, the
door will extend up to a 225° angle If the
oven is furnished with the retractable door
option, allow a minimum clearance of
6-1/2 inches (165mm).
❑ Allow a minimum clearance of 4-inches
(102mm) from the back of the oven for
plumbing connections.
❑ Allow a 20-inch (500mm) clearance at the top
of the oven for free air movement and for the
steam vent(s) located at the top.
❑ Do not install the oven adjacent to heat
producing equipment such as fryers, broilers,
etc. Heat from such appliances may cause
damage to the controls of the Combitherm.
Minimum clearance recommended:
20-inches (500mm)
Place the Combitherm oven on a stable, noncombustible level horizontal surface. For
countertop models, the oven
stand must be
level. In
addition, the
overall height of the oven should be positioned so
the operating controls and shelves may be
conveniently reached from the front. Level the
oven front-to-back and side-to-side by means of
the adjustable legs.
GAS COMBITHERM
PG.
12
—
I N S TA L L AT I O N M A N U A L
#MN-28898
®
V E N T I L AT I O N & I N S TA L L AT I O N R E Q U I R E M E N T S
COMBITHERM
DANGER
An adequate ventilation system is required for
commercial cooking equipment. Information may be
obtained by writing to the National Fire Protection
Association, Batterymarch Park, Quincy, MA 02269.
When writing refer to NFPA No. 96.
Installation, air adjustment and/or
service work must be in accordance
with all local codes and must be
performed by a certified service
technician qualified to work on
gas appliances.
1. A single gas Combitherm oven requires a
minimum of 28 CFM make-up air for natural and
propane gas. Kitchen ventilation must include a
provision for an adequate flow of fresh air for
gas combustion and to prevent a negativepressure condition. The bottom of the oven
provides air supply access for gas combustion
and must be kept clear at all times.
DO NOT obstruct or restrict ventilation nor the
air flow required to support combustion.
4. This oven cannot be direct vented.
5. Install the oven under a ventilation hood meeting
all applicable code requirements. Combustion
fumes must be vented in accordance with local,
state, or national codes.
DANGER
2. DO NOT obstruct the flow of the exhaust flue at
the top rear of the oven. It is especially critical
that gas supply piping and electrical support
cord and/or receptacle be routed away from the
path of the hot combustion fumes.
FAILURE TO VENT THIS APPLIANCE
PROPERLY MAY BE HAZARDOUS TO
THE HEALTH OF THE OPERATOR.
Equipment damage, operational
problems and unsatisfactory baking
performance may also be the
consequence of improper venting.
Any damage sustained by a failure to
properly vent this oven are not
covered under warranty.
CAUTION
To prevent malfunction or cause
negative back draft, DO NOT obstruct
exhaust flues or attach any flue
extension that will impede proper
burner operation.
CAUTION
3. Make certain the oven installation maintains
adequate air ventilation to provide cooling for
electrical and gas components. The area around
the oven should be clear of any obstructions
which might retard the flow of cooling air.
Failure to observe this caution may result in
damage to the components and will void the
warranty.
WA R N I N G
Inadequate ventilation, or failure to
ensure an adequate supply of fresh
air will result in a high ambient
temperature at the rear of the
appliance. An excessive ambient
temperature can cause the thermaloverload protection device on the
blower motor to trip resulting in severe
damage to the blower motor.
GAS COMBITHERM
—
DO NOT USE CIRCULATING FANS
ON THE FLOOR. FLOOR FANS WILL
AFFECT BURNER OPERATION.
Ve n t i l a t i n g h o o d s a n d e x h a u s t s y s t e m s s h a l l b e
permitted to be used to vent appliances installed in
commercial applications.
Where automatically operated appliances are vented
through a ventilating hood or exhaust system equipped
with a damper or with a power means of exhaust,
provisions shall be made to allow the flow of gas to the
main burners only when the damper is open to a position
to properly vent the appliance and when the power means
of exhaust is in operation. IN ACCORDANCE WITH NFPA 54
COMMONWEALTH OF MASSACHUSETTS ONLY.
I N S TA L L AT I O N M A N U A L
#MN-28898
PG.
13
E L E C T R I C A L & I N S TA L L AT I O N R E Q U I R E M E N T S
MODEL
VOLTAGE
PHASE
CYCLE/HZ
AMPS
1
50/60
9.5
1.14
20 A
9.5
1.14
7•14esG
110-120
1
50/60
5.7
10•10esG
110-120
1
50/60
5.7
10•20esG
110-120
1
50/60
12•18esG
110-120
1
20•20esG
110-120
1
7•14esG/ SK 110-120
10•10esG/ SK 110-120
1
1
50/60
CIRCUIT
110-120
6•10esG/ SK 110-120
1
KW
6•10esG
5.7
.68
20 A
.68
20 A
.68
20 A
7.8
.936
20 A
50/60
7.8
.936
20 A
50/60
22.0
2.64
30 A
50/60
50/60
OTHER VOLTAGES AVAILABLE :
9.5
20 A
1.14
20 A
2
AWG
WIRE
PLUS GROUND
AWG 12
2 WIRE
PLUS GROUND
AWG 12
2 WIRE
PLUS GROUND
AWG 12
2 WIRE
PLUS GROUND
AWG 12
2 WIRE
PLUS GROUND
AWG 12
2 WIRE
PLUS GROUND
AWG 10
Range 200 — 415V, 1 or 3 ph, 50 or 60 Hz
DANGER
DANGER
ELECTRICAL GROUNDING
INSTRUCTIONS:
AVERTISSEMENT: Directives
pour la prise de courant électrique Cet
appareil est muni d'une fiche à trios
branches (prise de Courant) afin de
vous proéger des chocs et doit être
branché Directemet dans un receptacle
adequate de prise do courant À trios
branches. II ne faut pas couper ou
enlever une banche De cette fiche.
This appliance is equipped with a
three-pronged (grounding) plug for
your protection against shock hazard
and should be plugged directly into a
properly grounded three-prong
receptacle. Do not cut or remove the
grounding prong from this plug.
An electrical wiring diagram is located behind the
control panel on the left side of the oven. This
appliance must be branch circuit protected with proper
ampacities, in accordance with the wiring diagram
located in the electrical compartment of the oven.
Wire size for the main incoming power to the unit
must match the minimum size listed in the
specifications applicable to the specific oven model.
For supply connections, locate the wire size posted on
the label located on the electrical control box cover,
behind the service panel.
380-415V:
To prevent an electrical shock hazard
between the appliance and other appliances
or metal parts in close vicinity, an
equalization-bonding stud is provided.
An equalization bonding lead must be
connected to this stud and the other
appliances / metal parts to provide
sufficient protection against potential
difference. The terminal is marked with
the following symbol.
Before operating the oven, check all cable connections
in the electrical connection area for tightness since
connections can loosen during transport.
NOTE: After both water and electrical connections
have been completed, operate the oven in
any cooking mode for a period of 15 minutes
and recheck the main power connections at
the terminal block to make certain they
remain tight.
GAS COMBITHERM
PG.
14
®
COMBITHERM
—
I N S TA L L AT I O N M A N U A L
DANGER
To avoid electrical shock, this
appliance MUST be adequately
grounded in accordance with local
electrical codes or, in the absence of
local codes, with the current edition
of the National Electrical Code
ANSI/NFPA No. 70. In Canada, all
electrical connections are to be
made in according with CSA C22.1,
Canadian Electrical Code Part 1 or
local codes.
#MN-28898
I N S TA L L AT I O N R E Q U I R E M E N T S
®
COMBITHERM
D R I P T R AY I N S TA L L AT I O N
The appliance is shipped without the drip tray
installed. This must be installed before equipment
operation begins.
� Remove screws from bottom of oven (see illustration
shown at right).
� Position drip tray assembly beneath oven. Secure with
lock washer and phillips screws supplied.
�
�
� Cut drip tray hose to length and attach to drip tray
assembly. Secure with 20mm clamp. Secure other end
of drip tray hose to drain fitting connection with clamp.
�
WA R N I N G
BOTTOM VIEW
FAILURE TO PROPERLY INSTALL THE
DRIP TRAY CAN OR WILL CAUSE
MAJOR EQUIPMENT DAMAGE AND
WILL RESULT IN A LEAKAGE
HAZARD THAT CAN CAUSE
PERSONAL INJURY.
—
1
—
SCREWS
2
—
DRIP TRAY
PART DESCRIPTION
HO-2957 DRIP TRAY HOSE
1. Install a manual gas shut-off valve along with an
approved disconnect device.
2. Install an A.G.A. certified, heavy-duty connector
that complies with ANSI Z 21.69 or CAN 1-6.10m88
along with a quick-disconnect device in compliance
with ANSI Z21.41 or CAN 1-6.9m70. Connectors
Adequate means must be provided to limit the
movement of this appliance. Limitation of
movement must be made without depending on
the connector, the quick disconnect device, nor the
associated piping designed to limit appliance
movement. If it becomes necessary to disconnect
the restraint, it must be reconnected immediately
following the return of the appliance to its
original position.
GAS COMBITHERM
PART
NO .
3
MOBILE EQUIPMENT RESTRAINT
The gas Combitherm must use a connector that
complies with The Stand ard for Connectors for
Movable Gas A ppliances, ANSI Z21.69 CSA 6.16
and addenda Z21.69a-1989. A quick disconnect
devise must be installed to comply with The
Stand ard for Quick Disconnect Devices for Use
with Gas Fuel, ANSI Z21 CSA 6.9.
ITEM
NO .
must be installed with a cable restraint to prevent
excessive tension from being placed on the
connector.
I N S TA L L AT I O N M A N U A L
WA R N I N G
RISK OF ELECTRIC SHOCK.
Appliance must be secured
to building structure.
#MN-28898
PG.
15
G A S S U P P LY & I N S TA L L AT I O N R E Q U I R E M E N T S
®
COMBITHERM
S P E C I F I C AT I O N S
The Alto-Shaam gas Combitherm has been set to
DANGER
operate with either natural gas or propane as indicated
on the identification name plate. Make certain the gas
CONNECTING TO THE WRONG GAS
SUPPLY COULD RESULT IN FIRE OR
AN EXPLOSION CAUSING SEVERE
INJURY AND PROPERTY DAMAGE.
supply matches the nameplate information. Should
conversion to the opposite fuel be desired, conversion
parts must be ordered from the factory. Conversion must
be completed by a qualified service person only. Always
remember to reflect the conversion on the oven's
WA R N I N G
nameplate. Residential gas connections and hard-piped
gas connections DO N OT meet NSF certifications.
TO AVOID SERIOUS PERSONAL
INJURY, installation of this appliance
must conform to local, state, and
national codes; the current edition of
the American National Standard
Z223.1, National Fuel Gas Code, and
all local municipal building codes. In
Canada, installation must be in
accordance with Standard CAN/CSA
B 149.1 and Installation Codes - Gas
Burning Appliances, and local codes.
G A S S P E C I F I C AT I O N S
■
6•10esG
10•10esG
7•14esG
10•20esG
12•18esG
20•20esG
NATURAL GAS
■
PROPANE GAS
45,000 Btu/hr .
45,000 Btu/hr .
91,000 Btu/hr .
91,000 Btu/hr .
68,000 Btu/hr .
105,000 Btu/hr .
105,000 Btu/hr .
190,000 Btu/hr .
68,000 Btu/hr .
105,000 Btu/hr .
105,000 Btu/hr .
G A S P R E S S U R E C H A RT
190,000 Btu/hr .
The oven has been factory adjusted according
I N S TA L L AT I O N R E Q U I R E M E N T S
GAS CONNECTION : 3/4" NPT
CHECK PLUMBING CODES FOR PROPER SUPPLY LINE SIZING TO
ATTAIN MINIMUM BURNER MANIFOLD PRESSURE SHOWN :
NATURAL GAS :
3.4" W.C.
PROPANE GAS : 5.6" W.C.
On 20•20esG models, the bottom valve should be set all
the way open and the the upper valve should be set to
the appropriate manifold pressure.
MAXIMUM INLET PRESSURE : 14" W.C.
NOTE: If a flexible gas line is used, it must be AGA
approved, commercial type and at least 3/4 " I.D.
HOOD INSTALLATION IS REQUIRED
GAS VALVE MAY REQUIRE FIELD ADJUSTMENT ABOVE
3,250' (991m)
AND IS NOT ADJUSTED AT THE FACTORY.
to the gas type specified on the identification
name plate.
TECHNICAL SPECIFICATIONS
Natural Gas
Min. Connected Pressure
5.5" W.C.
1.12 kPa
Max. Connected Pressure
14.0" W.C.
3.5 kPa
Min. Connected Pressure
9.0" W.C.
1.99 kPa
Max. Connected Pressure
14.0" W.C.
3.5 kPa
Propane Gas
GAS COMBITHERM
PG.
16
—
I N S TA L L AT I O N M A N U A L
#MN-28898
G A S S U P P LY & I N S TA L L AT I O N R E Q U I R E M E N T S
®
COMBITHERM
CONNECTION
DANGER
DANGER
Installation, air adjustment and/or
service work must be in accordance
with all local codes and must be
performed by a certified service
technician qualified to work on
gas appliances.
DO NOT store or use gasoline or other
flammable vapors or liquids in the
vicinity of this or any other appliance.
Remove any tape or
INCORRECT
CORRECT
compound residue
on all external
thread connections
before proceeding.
Use an approved gas
pipe sealant at all
external threaded
connections, Gas
piping used on gas
connections must avoid sharp bends that may restrict
the flow of gas to the appliance. If the connected
pressure exceeds 14.0" W.C. (3.5 kPa), a step-down
regulator is required to be supplied by the
owner/operator.
Close the individual manual shut-off valve to
isolate th e ap p lian ce from the gas supply piping
system during any pressure testing at test pressures
equal to or less than 1/2 psig. (3,4 kPa). The
appliance and individual shut-off valve m u st b e
d iscon n e cte d from the gas supply piping system
during any pressure testing at pressures in excess of
1/ " psig. (3,4 kPa).
2
DANGER
DO NOT store or use gasoline or other
flammable vapors or liquids in the
vicinity of this or any other appliance.
In the U.S.A., installation must conform to local
codes or, in the absence of local codes, with the
current edition of the N ational Fu e l Gas Cod e ,
NFPA-54 and ANSI Z83.11a CSA 1.8a 2004 (or
latest edition). In Canada, installation must be in
accordance with local codes, CAN/CGA-B149.1,
Installation for N atu ral Gas Bu rning A p p liance s
and Equ ip m e nt (latest edition) or CAN/CGAB149.2 Installation for Prop ane Bu rning A p p liance s
and Equ ip m e nt (latest edition).
The inlet supply line must be properly sized to
accommodate all individual appliances
simultaneously used on the sa me line but must
never be smaller than 3/4 " NPT.
A
B
C
E
G
D
F
H
GAS INTAKE
A-G Installation elbow
B Wall Valve
C-D Three-piece union fitting
(minimum 1 per installation)
E-F End connector for the flexible tube
H Marking line
GAS COMBITHERM
—
I N S TA L L AT I O N M A N U A L
#MN-28898
PG.
17
G A S S U P P LY & I N S TA L L AT I O N R E Q U I R E M E N T S
®
COMBITHERM
The minimum size requirement for gas piping or a
flexible connector is 3/4 - inch (19mm). For long runs
of gas piping, the pipe diameter must conform to the
tables in the National Fuel Gas Code, ANSI/NFPA
Z223.1.
A listed gas shut-off valve must be installed
upstream of the appliance to shut off the gas supply
during servicing. The shut-off valve should be
accessible with the appliance in the normal
installation position.
If the oven or the oven stand is supplied with
casters, gas connection must be made with a flexible
connector that complies with the Standard for
Connectors for Movable Gas Appliances, ANSI
Z21.69; or in Canada, Connectors for Movable Gas
Appliances, CAN/CGA-6.16-M87. When using a
flexible connector, a quick disconnect device must
be used to comply with the Standard for QuickDisconnect Devices for Gas Fuels, ANSI Z21.41; or
in Canada, Quick Disconnect Devices for Use with
Gas Fuels, CAN1-6.9.
When a quick disconnect device and flexible
connector are used, a restraining device must be
installed to limit the movement of the appliance and
prevent damage to the connector or quick
disconnect. An example of a restraining device
would consist of a 2000 pound test, stainless steel
cable, attached to a structural member of the kitchen
wall behind the oven. The means of attachment
should consist of a q u i c k c o n n e c t s n a p s o t h a t
t h e o v e n c a n b e disconnected when the appliance
GAS COMBITHERM
PG.
18
—
must be moved away from the wall.
The other end of the cable should be permanently
attached to the rear frame of the oven. The cable
should be of sufficient length so that no strain is
ever placed on the flexible gas connector in the
event of accidental movement of the oven without
properly disconnecting the gas connector. The
f l e x i b l e connector should be routed to form a
downward "U" loop between the building gas
supply and the permanent attachment at the rear of
the oven.
The routing of the flexible connector must not be
made under the oven. Oven temperatures achieved
during operation are too hot for safe operation. Gas
piping should be installed from the point of gas
connection at the bottom, front of the oven to the
back of the oven where the flexible connector may
be safely used. See the illustration for the
recommended placement.
WA R N I N G
I N S TA L L AT I O N M A N U A L
GAS PIPING MUST NEVER
BE INSTALLED TO RUN
UNDER THE BURNER .
#MN-28898
®
G A S S U P P LY & I N S TA L L AT I O N R E Q U I R E M E N T S
COMBITHERM
LEAK TESTING
If a pressure leak test above 1/2 psi is to be
performed on the building supply gas piping, the
shut-off gas valve and oven inlet gas supply line
must be disconnected from the building supply
piping before conducting the pressure test. Failure
to do so may result in damage to the manual gas
valve, gas components in the oven, or both.
If any gas leak tests are to be conducted at pressures
equal to or below 1/2 psi, the manual gas shut-off
valve upstream of the oven must be turned off
before conducting the tests.
Leak testing of the internal oven piping system was
conducted before shipping the oven from the
factory. If additional testing is needed, it should
only be conducted at normal gas supply pressures.
If the testing is performed using combustible gas in
the piping, the leak checking should be done with a
soap solution (bubble checking).
The use of an electronic combustible gas leak detector
is helpful, however, this type of detector can
be oversensitive. Electronic detectors may indicate
false leaks from other sources which would not be
detected when checking with a liquid solution to
verify a no-hazard gas connection.
When starting the oven after initial installation, the
gas lines must be free of air. It may take up to 30
minutes to eliminate all air from the lines. If, after
this time there is no pilot, call for factory assistance.
DANGER
NEVER USE AN OPEN
FLAME TO LEAK TEST.
GAS EXHAUST
The oven is not designed for direct connection to
a chimney vent system or for direct connection
to a horizontal exhaust system.
The oven must be installed under a ventilation
hood listed to ANSI/UL 70 5 (latest ed ition),
and the installation must be completed in
a c c o r d a n c e w i t h t h e A N S I / N F PA 9 6 - 1 9 8 7 ,
S t a n d a r d f o r Ve n t i l a t i o n C o n t r o l a n d F i r e
Protection of Commercial Cooking Operations.
Oven operators should be instructed with regard
to the hazards of placing any material on top of
the oven that would obstruct the flow of flue
products out the opening of
the flue diverter. Operators
s h o u l d a l s o b e i n s t ru c t e d
with regard to the hazards of
hot flue gases and that any
material or items placed on
top of, or in front of the flue
defector could be damaged or
cause a fire hazard.
GAS COMBITHERM
—
I N S TA L L AT I O N M A N U A L
DANGER
BEFORE STARTING THE
APPLIANCE, MAKE CERTAIN
YOU DO NOT DETECT THE
ODOR OF GAS.
IF THE ODOR OF GAS IS DETECTED:
• DO NOT attempt to light any appliance.
• DO NOT touch any electrical switches.
• Extinguish any open flame.
• Use a telephone OUTSIDE THE
PROPERTY & IMMEDIATELY
contact your gas supplier.
• If unable to contact your gas supplier,
contact the fire department.
#MN-28898
PG.
19
WAT E R S U P P LY & I N S TA L L AT I O N R E Q U I R E M E N T S
®
COMBITHERM
WAT E R Q U A L I T Y R E Q U I R E M E N T S
USE A DRINKING QUALITY, COLD WATER SUPPLY ONLY
Water quality is of critical importance when
installing steam producing equipment of any kind,
particularly high temperature steam producing
equipment. Water that is perfectly safe to drink is
composed of chemical characteristics that directly
affect the metal surfaces of steam producing
equipment. These chemical characteristics differ
greatly from region to region throughout the U.S.
and the world. Varying combinations of pH ;
alkalinity; hard ness; chlorid es; total d issolved
solid s; and other chemical characteristics, when
subjected to hig h temperatures, will cause water to
have a tend ency to either scale or corrod e.
Alto-Shaam has consulted with people who
understand the properties of water in order to
provide water quality standards that meet the
broadest possible range of acceptable water quality
requirements to help protect your investment.
We strongly urge water testing to ascertain the
water quality on site prior to the installation of any
steam producing equipment. Since water quality is
an important issue, Alto-Shaam is committed to
provide as much information as possible to help
protect the investment made in this equipment.
A CombiGuard ™ Water Filtration System can be
purchased as an option for installation on the
Combitherm oven. This filter, when properly
installed, maintained, and combined with the
required levels of steam generating equipment
maintenance, will help lessen the affect water has on
metal surfaces. It will not, however, provide
complete protection against all water damage from
region to region.
Due to the complexity of water chemistry, it is
important to understand that water quality plays a
significant role in the longevity of steam producing
equipment. Water quality and required
maintenance of steam generating equipment is the
direct responsibility of the owner/operator.
Damage incurred as a direct result of poor water
quality and/or surfaces affected by water quality is
also the responsibility of the owner/operator.
Damage due to water quality that does not meet the
minimum standards shown below is not covered
under the Alto-Shaam Combitherm warranty.
Alto-Shaam will continue our efforts to provide
viable solutions to ease the impact of water quality
as it relates to steam generating equipment.
ALTO-SHAAM COMBITHERM WATER QUALITY MINIMUM STANDARDS
CONTAMINANT
INLET WATER REQUIREMENTS (UNTREATED WATER)
Free Chlorine
Less than 0.1 ppm (mg\L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg\L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg\L)
Silica
Less than 12 ppm (mg\L)
Total Dissolved Solids (tds)
Less than 60 ppm
WA R N I N G
WA R N I N G
TO PREVENT WATER PIPES OR HOSES
FROM BURSTING, INCOMING WATER
SUPPLY SHOULD BE TURNED OFF
WHEN THE APPLIANCE IS NOT IN USE.
GAS COMBITHERM
PG.
20
—
WATER SUPPLY MUST BE OPEN WHEN
CLEANING PROGRAM IS ACTIVATED.
VERIFY WATER SUPPLY BEFORE STARTING
CLEANING PROGRAM.
I N S TA L L AT I O N M A N U A L
#MN-28898
®
WAT E R S U P P LY & I N S TA L L AT I O N R E Q U I R E M E N T S
COMBITHERM
Flush the water line at the installation site.
TWO (2) COLD WATER INLETS - DRINKING QUALITY
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
* Can manifold off of one 3/4" line
WAT E R R E Q U I R E M E N T S
Install water intake filters (provided) [see figure 1] before
connecting the oven to the water supply.
ONE (1) TREATED WATER INLET:
A hose connector is supplied for flexible hose connection
to the COLD water source.
PIPE SEALING TAPE ( TEFLON ®) MUST BE USED AT
ALL CONNECTION POINTS. The use of a pipe sealing
REFER TO PUBLISHED SPECIFIC WATER REQUIREMENTS
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
compound is not recommended.
Install water
intake filters
ONE SUGGESTED
METHOD OF INSTALLATION
Incoming cold water
connection
Fig. 1
Water Filter
T connection
Cold water line to
untreated oven
connection
Cold water line to
filter or treatment
system
Treated cold
water to treated
connection on oven
NOTE:
BOTH TREATED A N D UN TREATED WATER
CON N ECTION S MUST BE CON N ECTED FOR PROPER
OPERATION OF TH E OV EN . BOTH CON N ECTION S
CA N BE TREATED WATER, BUT SH OULD N EV ER BE
CON N ECTED TO ON LY UN TREATED WATER.
UN ION S OR FLEXIBLE LIN ES SH OULD BE USED TO
A LLOW FOR OV EN MOV EMEN T WH EN BEIN G
SERV ICED OR CLEA N IN G IS N EEDED.
REFER TO DIMEN SION DRAWIN GS BEGIN N IN G ON
PA GE 4 FOR PROPER IN TA KE LOCATION S.
GAS COMBITHERM
—
I N S TA L L AT I O N M A N U A L
#MN-28898
PG.
21
WAT E R S U P P LY & I N S TA L L AT I O N R E Q U I R E M E N T S
®
COMBITHERM
S H U T - O F F V A LV E S H O W N
IN THE OFF POSITION
NOTE:
TH E SH UT-OFF VA LV E
MUST BE IN TH E OPEN POSITION
WH EN TH E OV EN IS BEIN G USED.
ITEM FI-23014
Alto-Shaam now offers an improved water filtration system for
Combitherm®. The CombiGuard™ triple-guard water filtration system filters
dirt, sediment, and other debris as small as 1/2 micron. This system also
significantly reduces chlorine content to protect against corrosive chlorine
compounds. CombiGuard improves equipment efficiency, reduces service
requirements and extends the life of the Combitherm. Filtration system
includes one filter cartridge. Additional cartridges (FI-26356) can be
purchased separately.
GAS COMBITHERM
PG.
22
—
I N S TA L L AT I O N M A N U A L
#MN-28898
®
WAT E R S U P P LY & I N S TA L L AT I O N R E Q U I R E M E N T S
COMBITHERM
WAT E R D R A I N A G E
The oven must discharge through an indirect waste pipe by means of an air gap. The drain fitting is
supplied with a 1-1/2-inch (41mm) NPT thread.
A union is required. Install a 1-1/2-inch (41mm)
diameter connection, drain line and clamp into
place. The drain line must always be a positive
gradient away from the Combitherm oven and not
more than 12-inches (305mm) before an air gap.
NOTE: In the U.S.A., this equipment is to be
installed to comply with the Basic
Plumbing Code of the Building Officials
and Code Administrators International,
Inc. [BOCA], and the Food Service
Sanitation Manual of the Food & Drug
Administration [FDA].
2" (51mm)
Air Gap
If several units are to be connected to one drain
pipe, the dimensions of the pipe must be sufficient
to allow an unobstructed water drain system.
1-1/2"(32mm)
(41mm)diameter NPT
1-1/4"
diameter connection
required
WASTE PIPE
1-1/2" to 2" minimum diameter
(c. 38mm to 51mm)
1-1/2” (41mm)
diameter NPT
condensate pan
clean out
GAS COMBITHERM
—
I N S TA L L AT I O N M A N U A L
#MN-28898
PG.
23
I N S TA L L AT I O N C H E C K L I S T
®
Use this list as a final check of oven installation conformance. Damage directly attributed to improper set up, installation,
or cleaning can invalidate warranty claims.
COMBITHERM
ARE ALL CLEARANCE
CLEARANCES:
Left:
6” (152mm) — Service access of 18” (457mm) recommended.
20” (508mm) from heat producing equipment.
Right: 4” (102mm)
Back: 4” (102mm) for plumbing
Top:
20” (508mm) for air movement
REQUIREMENTS MET?
Verify electrical power
requirements for oven.
Verify voltage at terminal
block. Check all terminals
________________________________________
ARE BOTH WATER SUPPLY LINES
PROPERLY CONNECTED? ■ YES
■ NO
IF NO, EXPLAIN: __________________________
IS A FILTER SYSTEM INSTALLED
■ YES
ON THIS UNIT?
STORE HAS SEEN THIS
RECOMMENDATION:
■ YES
■ NO
■ NO
SIGNATURE OF STORE REPRESENTATIVE:
___________________________________________
VOLTAGE: ______________ LINE VOLTAGE AT TERMINAL BLOCK (TO GROUND):
PHASE: ______________
BREAKER SIZE: ______________
➥ LINE 1: _________ LINE 2:_________ LINE 3: _________
LINE VOLTAGE (PHASE TO PHASE): LINE 1 to 2: __________
LINE 2 to 3: __________
LINE 3 to 1: __________
ELECTRICAL SUPPLY LINE SIZE: ______________
for tightness.
CORRECT MOTOR ROTATION: ■ YES
ALL ELECTRICAL TERMINALS TIGHT: ■ YES
■ NATURAL GAS
G A S C O N N E C T I O N S ( G A S U N I T S O N LY ) :
Verify that gas connections are 3/4" NPT pipe or 3/4" commercial
flexible gas connector. Verify incoming gas pressure is at least 5.5"
WC for natural gas and 9" WC for propane. Verify that gas valve
outlet pressure is 3.4" WC for natural gas and 5.6" WC for propane.
Verify that if a commercial flexible gas connector is used that it is not
run under the oven, but connected at the rear of the oven.
C O N T RO L B OA R D C O N N E C T I O N S & O P E R AT I O N :
With the Power Key OFF , press and hold the Chef Function
Key to access software version, and record.
SOFTWARE VERSION:
BM_____________ SM_____________ KM_____________
PHYSICAL CONDITION:
■ NO
IF NO, EXPLAIN: ________________________
WAT E R S U P P LY A N D D R A I N S :
Verify hook-up to TWO (2) separate cold water supply lines with a 3/4" (19mm)
water connection supply line. Verify inlet water pressure is at a minimum of 30 PSI
(2.8 bar). Maximum water pressure is not to exceed 90 PSI (6 bar). Verify drain
diameter of 1-1/2" (41mm) with a positive descending slope, and with a 2" (51mm)
air gap which is free of obstructions before connection to the site drain. Verify 1/8"
(3,2mm) pitch to 10' (305cm) of drain line.
IMPORTANT: Alto-Shaam has listed Water Quality Requirements in the
installation manual for this equipment. It is the responsibility of the end user
to have the water connected to this appliance tested to ensure these standards
are met before putting the oven into use. Failure to meet these standards will
void the warranty if damage to the oven is found to be related to water quality.
ELECTRICAL CONNECTIONS:
■ YES
*REFERENCE
■ NO
■ NO
■ PROPANE
GAS CONNECTION: __________
INCOMING GAS PRESSURE: __________
GAS OUTLET PRESSURE: __________
CONNECTION AT REAR OF OVEN: __________
ALL BOARD CONNECTIONS TIGHT: ■ YES
ALL FUNCTIONS LIGHT UP: ■ YES
ALL FUNCTIONS ON CONTROL OPERATE: ■ YES
■ NO
■ NO
■ NO
UNIT OPERATES IN ALL MODES: ■ YES ■ NO
IF NO, EXPLAIN: ________________________________________
I N S TA L L AT I O N I N S T R U C T I O N S F O R C O M P L E T E I N F O R M AT I O N
✔
Bottom of oven has been checked for damage due to improper positioning on site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .■
■
■
Verify all gaskets, hoses, and carts* are in place and function properly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .■
If oven includes a cart, verify proper installation of the rack guide* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .■
■
Verify the installation of drip pans* , racks, shelves, drain screen, spray hose* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .■
■
■
Verify the oven is level and installed on a solid, water resistant floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .■
SERVICE AGENCY:
START-UP DATE:
INSTALLATION NAME:
MODEL NO.:
SERIAL NO.:
TECH SIGNATURE:
CUSTOMER SIGNATURE:
GAS COMBITHERM
PG.
24
—
I N S TA L L AT I O N M A N U A L
#MN-28898
ERROR CODES
®
COMBITHERM
CONTROL RESET
There is a remote possibility in the day-to-day operation of the Combither m that the control could
lock or freeze. If this occurs, the control is easy to reset.
PRESS AND HOLD THE POWER KEY FOR A PERIOD OF 5 SECONDS.
Release the POWER KEY.
The control will will reset itself within approximately 15 seconds.
WHEN RESET, THE DISPLAY WILL INDICATE THE TIME AND DATE AND THE CONTROLS WILL BE FULLY FUNCTIONAL.
SERVICE MODE AND ERROR CODES
When the oven malfunctions, an error code will appear in the display.
PRESS THE START KEY TO ACKNOWLEDGE THE ERROR.
The keys that begin to flash represent operational modes that are still usable. Refer to Emergency
Operation.
When the oven fault is corrected, the Combitherm will return to normal Operation.
ERROR CODES AND REASONS
Error
Code
E01
Display Shows
Low Water
When does the error occur?
Possible reason
ES units only:
• Activated if running in any mode and the
water level drops below the low level
sensor.
• Water supply is shut off.
• Activated if in Standby mode and the water
level drops below the low level sensor for
3 minutes.
• Drain pump is not sealing.
• Low water pressure.
• Steam generator drain cap is off or loose.
• Faulty or scaled water level probe.
• Faulty or plugged solenoid valve assembly.
• Wiring or connection issue.
E02
Control Temp High
Activated if the temperature of the electrical
control is higher than 176°F (80°C) for 20
seconds.
• Cooling fan not operating.
• Unit is next to a heat producing source
(there is less than 20" clearance for the
control side).
• Exhaust hood is not operating (if applicable).
E03
Fan Malfunction
Activated if the motor protection switch is
tripped.
• Motor rotation is backwards.
• Incorrect power to the unit.
• Connection problem at X-7 plug on the relay
board pins 3-4.
E04
Aux Fan Fault
Auxiliary fan malfunction.
• Control setup programming error.
• Contact factory.
E11
Excess Oven Temp
Activated if the oven cavity temperature is
higher than 572°F (300°C) for 25 seconds.
• Connection issue with oven temperature
sensor.
• Convection element contactor is stuck.
• Faulty oven temperature sensor.
GAS COMBITHERM
—
I N S TA L L AT I O N M A N U A L
#MN-28898
PG.
25
ERROR CODES
®
COMBITHERM
ERROR CODES AND REASONS (continued)
Error
Code
E13
Display Shows
Excess Steam Gen Temp
When does the error occur?
ES units only:
Activated if the temperature of the steam
generator probe (B-4) is higher than 248°F
(120°C) for 26 seconds.
Possible reason
• Problem with water level probe.
• Scale build-up inside steam generator.
• Steam element contactor is stuck.
• Connection issue with B-4 probe.
• Faulty B-4 probe.
E15
Excess Condensate Temp
ESi units only:
• Activated if the position of personality
jumper on X-3 is incorrect.
• Jumper on X-3 is improperly positioned.
Should be between 2-8 or, if it is a smoker,
between 2-9.
• Activated if the position of B-4 jumper is
incorrect.
• Jumper on X-6a is improperly positioned.
Should be between 13-14.
Activated if the temperature of the
condensate probe (B-3) is higher than 212°F
(100°C) for 26 seconds.
• Water supply is shut off.
• Faulty or plugged solenoid valve (Y-2).
• Connection issue at B-3 probe.
• Faulty B-3 probe.
E21
E22
Oven Probe Fault
Core Temp Probe Fault
Activated if oven temperature probe (N-6) is
interrupted.
• Connection issue at N-6 probe.
Activated if cooking in Core Temp mode and
the CTC sensor measures an excessive
temperature.
• CTC sensor is damaged.
• Faulty N-6 probe.
• 4-point CTC sensor is activated, but 1-point
CTC sensor is installed.
• Cable connection of CTC sensor is damaged.
• Hardware problem on control unit (SM).
E23
E24
E25
E26
E27
Steam Gen Probe Fault
ES units only:
Activated if the steam generator probe (B-4)
is interrupted.
• Connection issue at B-4 probe.
ESi units only:
• Activated if the position of personality
jumper on X-3 is incorrect.
• Jumper on X-3 is improperly positioned.
Should be between 2-8 or, if it is a smoker,
between 2-9.
• Activated if the position of B-4 jumper is
incorrect.
• Jumper on X-6a is improperly positioned.
Should be between 13-14.
Activated if the bypass probe (B-5) is
interrupted.
• Connection issue at B-5 probe.
Activated if the condensate probe (B-3) is
interrupted.
• Connection issue at B-3 probe.
Steam Gen Safety Probe
Fault
Activated if the steam generator safety probe
(N-8) is interrupted.
• Connection issue at N-8 probe.
Excess Steam Gen Safety
Temp
ES units only:
Activated if the steam generator safety probe
(N-8) measures a temperature in excess of
266°F (130°C).
• Problem with water level probe.
Bypass Probe Fault
Condensate Probe Fault
• Faulty B-4 probe.
• Faulty B-5 probe.
• Faulty B-3 probe.
• Faulty N-8 probe.
• Scale build-up inside steam generator.
• Steam element contactor is stuck.
• Connection issue with N-8 probe.
• Faulty N-8 probe.
ESi units only:
• Activated if the position of N-8 jumper is
incorrect.
GAS COMBITHERM
PG.
26
—
I N S TA L L AT I O N M A N U A L
• Jumper on X-6b is improperly positioned.
Should be between 1-2.
#MN-28898
ERROR CODES
®
COMBITHERM
ERROR CODES AND REASONS (continued)
Error
Code
E29
E34
Display Shows
Probe Short to Frame
DE (Drain) Pump Failure
When does the error occur?
Activated if one or more of the temperature
sensors were connected to GND for 5
seconds.
Possible reason
• Connection issue at any of the temperature
sensors.
• Temperature sensor shorted to
ground/faulty.
Activated if water level did not drop below
• Problem with water level probe.
the low level sensor in the generator during a
• Scale build-up inside steam generator.
steam generator flush.
• Scale plugging drain pump.
• Faulty drain pump.
E35
Venting Error
Activated when vent switch reads open (vent
closed) when it should be closed (vent open),
or when it reads closed (vent open) when it
should be open (vent closed).
• Alignment issue between motor cam and
micro switch.
• Connection issue at micro switch.
• Connection issue at control.
• Faulty vent switch.
• Faulty vent motor.
E36
Steam Temp High
Activated when oven temperature probe (N-6) • Water supply is shut off while unit is running
measures a temperature in excess of 395°F
in Steam or Combi mode.
(202°C) when running in Steam or Combi
• Plugged or faulty Y-1 solenoid.
mode.
• Obstruction between Y-01 solenoid and
water inlet.
E80
ID Error
Control is unable to detect whether unit is
gas or electric.
E81
Program Memory Error
• Connection issue at X-3 personality jumper.
• Faulty control.
Temperature value or time value of a program • Program was generated in °C and control
step is not allowed.
has been switched to °F.
• Program was generated in °F and control
has been switched to °C.
E82
WP Error
Temperature value or time value of current
cooking algorithm is out of allowed array.
• Delete program and reinstall.
E83
Algo Error
Cooking algorithm sent by operating module
(BM) is unknown to control unit (SM).
• Software versions of control unit and
operating module are incompatible.
• Software error in operating module.
E96
Connection Error
No or bad communication between control
unit (SM) and operating module (BM).
• Connection issue at ribbon cable on display
or relay board.
• Faulty ribbon cable.
• Software versions of control unit and
operating module are incompatible.
GAS COMBITHERM
—
I N S TA L L AT I O N M A N U A L
#MN-28898
PG.
27
ERROR CODES
®
COMBITHERM
E M E R G E N C Y O P E R AT I O N
In the event of an error code, the Combitherm may be operated on a limited basis. Error conditions under
which continued operation can be conducted are indicated by “Yes” in the chart shown below.
When the oven malfunctions, an error code will appear in the display.
PRESS THE START KEY TO ACKNOWLEDGE THE ERROR.
The keys that begin to flash represent operational modes that are still usable.
SELECT AND PRESS ONE OF THE COOKING MODES INDICATED.
The oven control will only respond to the mode keys that are flashing.
SET THE OVEN CONTROLS AS IF OPERATING UNDER NORMAL CIRCUMSTANCES.
Depending on the error code involved, oven function, such as temperature range, may be limited.
PRESS THE START KEY TO BEGIN THE COOKING PROCESS.
PRESS THE START KEY WHEN THE TIMER EXPIRES.
When the oven fault is corrected, the Combitherm will return to normal Operation.
CONTINUED OPERATION UNDER ERROR CONDITIONS
Error
Code
Display Shows
ES
ESi
Steam
Mode
Combination
Mode
Convection
Mode
Retherm
Mode
E01
Low Water
Yes
No
No
No
To 365°F
No
E02
Control Temp High
Yes
Yes
Yes
To 284°F
To 284°F
To 284°F
E03
Fan Malfunction
No
No
—
—
—
—
E04
Aux Fan Fault
Yes
Yes
Yes
To 284°F
To 284°F
To 284°F
E11
Excess Oven Temp
Yes
Yes
No
No
No
No
E13
Excess Steam Gen Temp
Yes
No
No
No
No
No
E15
Excess Condensate Temp
Yes
Yes
No
No
To 356°F
No
E21
Oven Probe Fault
Yes
Yes
212°F only
No
No
No
E22
Core Temp Probe Fault
Yes
Yes
Yes
Yes
Yes
Yes
E23
Steam Gen Probe Fault
Yes
No
Yes
Yes
Yes
Yes
E24
Bypass Probe Fault
Yes
Yes
To 210°F
No
Yes
No
E25
Condensate Probe Fault
Yes
Yes
Yes
To 356°F
To 356°F
To 320°F
E26
Steam Gen Safety Probe Fault
Yes
No
Yes
Yes
Yes
Yes
E27
Excess Steam Gen Safety Temp
Yes
No
No
No
No
No
E29
Probe Short to Frame
Yes
Yes
No
No
No
No
E34
DE (Drain) Pump Failure
Yes
No
Yes
Yes
Yes
Yes
E35
Venting Error
Yes
Yes
Yes
Yes
Yes
Yes
E36
Steam Temp High
No
Yes
No
No
Yes
No
E80
ID Error
Yes
Yes
Yes
Yes
Yes
Yes
E81
Program Memory Error
Yes
Yes
Yes
Yes
Yes
Yes
E82
WP Error
Yes
Yes
Yes
Yes
Yes
Yes
E83
Algo Error
Yes
Yes
Yes
Yes
Yes
Yes
E96
Connection Error
Yes
Yes
No
No
No
No
GAS COMBITHERM
PG.
28
—
I N S TA L L AT I O N M A N U A L
#MN-28898
®
O R I G I N A L E Q U I P M E N T L I M I T E D WA R R A N T Y
COMBITHERM
Alto-Shaam, Inc. warrants to the original purchaser that any original part that is found to be defective in material
or workmanship will, at Alto-Shaam’s option, subject to provisions hereinafter stated, be replaced with a new or rebuilt
part.
The labor warranty remains in effect one (1) year from installation or fifteen (15) months from the shipping date,
whichever occurs first. Alto-Shaam will bear normal labor charges performed by an authorized Alto-Shaam service
agent during standard business hours, and excluding overtime, holiday rates or any additional fees.
The parts warranty remains in effect for one (1) year from installation or fifteen (15) months from the shipping
date, whichever occurs first.
THIS WARRANTY DOES NOT APPLY TO:
1. Replacement of light bulbs.
2. Equipment damage caused by accident, shipping, improper installation or alteration.
3. Steam generator or steam generating system damage as a result of inadequate routine maintenance and
cleaning. Required maintenance and cleaning of steam generating equipment is the responsibility of the
owner/operator.
4. Equipment used under conditions of abuse, misuse, carelessness or abnormal conditions including, but not
limited to, equipment subjected to harsh or inappropriate chemicals including, but not limited to, compounds
containing chlorine, chlorides or quaternary salts, or equipment with missing or altered serial numbers.
5. Equipment that uses water must meet Alto-Shaam’s minimum water quality standards as shown below. USE OF
WATER NOT MEETING ALTO-SHAAM'S MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY.
Water quality and required maintenance of steam generating equipment is the responsibility of the
owner/operator. The installation and use of Alto-Shaam’s CombiGuard™ Water Filtration System is highly
recommended.
ALTO-SHAAM COMBITHERM WATER QUALITY MINIMUM STANDARDS
CONTAMINANT
INLET WATER REQUIREMENTS (UNTREATED WATER)
Free Chlorine
Less than 0.1 ppm (mg\L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg\L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg\L)
Silica
Less than 12 ppm (mg\L)
Total Dissolved Solids (tds)
Less than 60 ppm
6. Damage caused by use of any cleaning agent other than Alto-Shaam’s Combitherm® Oven Cleaner including,
but not limited to, damage due to chlorine, bleach, quaternary salts, scouring powders or other harmful
chemicals. Use of Alto-Shaam’s Combitherm Cleaner on Combitherm ovens is highly recommended.
7. Any losses or damage resulting from malfunction, including loss of product or other consequential or incidental
damages of any kind.
8. Equipment modified in any manner from original model, substitution of parts other than factory authorized
parts, removal of any parts including legs, or addition of any parts.
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN
NO EVENT SHALL ALTO-SHAAM BE LIABLE FOR LOSS OF USE, LOSS OF REVENUE OR PROFIT, OR LOSS OF
PRODUCT, OR FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
No person except an officer of Alto-Shaam, Inc. is authorized to modify this warranty or to incur on behalf of
Alto-Shaam any other obligation or liability in connection with Alto-Shaam equipment.
GAS COMBITHERM
—
O P E R AT I O N A N D C A R E M A N U A L
#MN-28898
PG.
29
TRANSPORTATION DAMAGE AND CLAIMS
®
COMBITHERM
All Alto-Shaam equipment is sold F.O.B. shipping point, and when accepted by the
carrier, such shipments become the property of the consignee.
Should damage occur in shipment, it is a matter between the carrier and the consignee.
In such cases, the carrier is assumed to be responsible for the safe delivery of the
merchandise, unless negligence can be established on the part of the shipper.
1. Make an immediate inspection while the equipment is still in the truck or immediately after it is moved to the
receiving area. Do not wait until after the material is moved to a storage area.
2. Do not sign a delivery receipt or a freight bill until you have made a proper count and inspection of all
merchandise received.
3. Note all damage to packages directly on the carrier ’s delivery receipt.
4. Make certain the driver signs this receipt. If he refuses to sign, make a notation of this refusal on the receipt.
5. If the driver refuses to allow inspection, write the following on the delivery receipt:
Driver refuses to allow inspection of containers for visible damage.
6. Telephone the carrier ’s office immediately upon finding damage, and request an inspection. Mail a written
confirmation of the time, date, and the person called.
7. Save any packages and packing material for further inspection by the carrier.
8. Promptly file a written claim with the carrier and attach copies of all supporting paperwork.
We will continue our policy of assisting our customers in collecting claims which have been properly filed and
actively pursued. We cannot, however, file any damage claims for you, assume the responsibility of any claims, or
accept deductions in payment for such claims.
RECORD THE MODEL AND SERIAL NUMBER OF THE APPLIANCE
FOR EASY REFERENCE. ALWAYS REFER TO BOTH MODEL AND SERIAL NUMBER
IN ANY CONTACT WITH ALTO-SHAAM REGARDING THIS APPLIANCE.
Model: ____________________________________________________
Serial Number: _____________________________________________
Date Installed: ______________________________________________
Voltage: ___________________________________________________
Purchased From:____________________________________________
___________________________________________________
___________________________________________________
PHONE:
W 1 6 4 N 9 2 2 1 Wa t e r S t r e e t • P. O . B o x 4 5 0 • M e n o m o n e e F a l l s , W i s c o n s i n 5 3 0 5 2 - 0 4 5 0 • U . S . A .
262.251.3800 • 800.558-8744 USA/CANADA
FAX: 262.251.7067 • 800.329.8744 U.S.A. ONLY
WEBSITE: www.alto-shaam.com
GAS COMBITHERM
PG.
30
Alto-Shaam has established a
twenty-four hour emergency service call
center to offer immediate customer access
to a local authorized service agency
outside of standard business hours. The
emergency service access is provided
exclusively for Alto-Shaam equipment
and is available throughout the United
States through the use of Alto-Shaam's
toll-free number. Emergency service
access is available seven days a week
including holidays.
—
I N S TA L L AT I O N M A N U A L
#MN-28898
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising