mitsubishi 2014 en-hp
NOTICE
cover_F.indd 1
S-179-3-C9236-B SI1401 Printed in Japan (MDOC)
Revised publication effective Jan. 2014.
Superseding publication of S-179-3-C9236-B Jul. 2013.
Specifications are subject to change without notice.
Eco Changes is the Mitsubishi Electric Group’s environmental statement,
and expresses the Group’s stance on environmental management.
Through a wide range of businesses, we are helping contribute to the
realization of a sustainable society.
■ When installing or relocating or servicing the air conditioners, use only the specified refrigerant (R410A) to charge the
refrigerant lines.
Do not mix it with any other refrigerant and do not allow air to remain in the lines.
If air is mixed with the refrigerant, then it can be the cause of abnormal high pressure in the refrigerant lines, and may result
in an explosion and other hazards.
The use of any refrigerant other than that specified for the system will cause mechanical failure, system malfunction or unit
breakdown. In the worst case, this could lead to a serious impediment to securing product safety.
■ Do not install indoor units in areas (e.g., mobile phone base stations) where the emission of VOCs such as phthalate
compounds and formaldehyde is known to be high as this may result in a chemical reaction.
SPLIT-TYPE
YPE AIR CONDITIONERS
COND
DITION
Full Product Line Catalogue 2014
13.12.12 1:14:49 PM
2014
Full Product Line Catalogue
Wrap Yourself in Comfort and Quiet
Eco-conscious Technologies from Japan
ECODAN
“ecodan” can heat rooms and supply domestic
hot water, realising greater comfort and energy saving.
“ecodan” – Economic, eco conscious next generation heating system
Both energy-saving and safe for the environment, the Mitsubishi Electric ecodan incorporates a highly efficient heat pump
system that captures “the heat in the air”, a renewable energy resource. Equipped with advanced inverter control, meticulous
temperature control assures comfortable heating, and its space-saving “All-in-one” indoor unit is easy to install. These energysaving, high comfort and simple installation characteristics have drawn the ecodan heating system into the spotlight centre
stage.
Excellent ecodan’s heating performance, even at low outdoor temperature!
INDOOR UNIT
Cylinder unit
Hydro box
Hydro box
(Reversible)
EHSC/EHPX
ERSC
EHST20C/EHPT20X
OUTDOOR UNIT
Split type
SHW230
Packaged type
SW100/120
SW75
SW40/50
HW112/140
W85
W50
126
P125-138.indd 126
13.12.12 1:25:37 PM
Unique technology of ecodan
Auto Adaptation
Settings can be
performed using
an SD card.
ecodan – Maximize energy savings while keeping comfort at all times
Aiming to realise further comfort and energy savings, Mitsubishi Electric is proud to introduce a
revolutionary new system control. This is based on data indicating that a 1°C drop in the flow temperature improves the coefficient of performance (COP) of the ATW system by 2%. This means
that energy savings are dramatically affected by controlling the flow temperature in the system.
■ Heat curve setting (Example)
Flow temp.
If flow
COP is
temperature is
lowered 1°C improved 2%
60°C
In conventional system control, the flow temperature is determined based on the preset heat
curve depending on the actual outdoor temperature. However, this requires a complicated setting to achieve the optimal heat curve.
30°C
-15°C
10°C
Outdoor temp.
Mitsubishi Electric’s Auto Adaptation function automatically tracks changes
of the actual room temperatures and outdoor temperatures and adjusts the flow temperature accordingly.
Our more evolutionary Auto Adaptation function measures the room temperature and outdoor temperature, and then calculates the required heating
capacity for the room. Simply stated, the flow temperature is automatically controlled according to the required heating capacity, while optimal room
temperature is maintained at all times, ensuring the appropriate heating capacity and preventing energy from being wasted. Furthermore, by
estimating future changes in room temperature, the system works to prevent unnecessary increases and decreases in the flow temperature.
Accordingly, Auto Adaptation maximises both comfort and energy savings without the need for complicated settings.
■ Two Controls simulation on a day
Temperature/
Heating Load
Curtain
opened
Ventilation fan
turned on
Increase in Lights
occupants turned off
Changes in room conditions
1 Room temperature slightly increases
2 Flow temperature decreases
Flow temp.
4
Energy savings
2
3 Room temperature decreases
Room temp.
Temperature
setting
4 Flow temperature slightly increases
Comfort
3
1
The flow temperature through the system controlled
via conventional heat curve
Outdoor temp.
The flow temperature through the system controlled
via Mitsubishi Electric’s Auto Adaptation function
6:00
■ Future room temperature estimation
Room temp.
Target temp.
12:00
18:00
Time
24:00
(a) Higher than the target room temp.
lower the flow temp.
(b) Approximately same as the target temp.
keep the flow temp.
(c) Lower than the target room temp.
raise the flow temp.
Modify the flow temperature by comparing
actual and estimated room temperature.
3 points
T0 T1 Current
Future
Time
All-in-one & compact
Small overall size contributes to easy transportation, installation and maintenance
• Simplified: All key functional components are incorporated into the unit.
• Easy servicing: Relevant parts are located at the front of the unit to
access easily.
• Easy to transport and install using the attached handle both at front
and at back (cylinder unit) and also back plate (hydro box unit).
• Easy to open the packaging without using knife.
Compact hydro box unit
*EXPANSION VESSEL
CONTROL AND
ELECTRICAL BOX
Compact cylinder unit
MANOMETER
*EXPANSION VESSEL
(behind)
HANDLES (back)
CONTROL AND
ELECTRICAL BOX
MAIN REMOTE
CONTROLLER
3-WAY VALVE
PUMP VALVE
WATER PUMP
TANK
*PLATE HEAT
EXCHANGER
BOOSTER HEATER
*PLATE HEAT
EXCHANGER
BOOSTER HEATER
PUMP VALVE
STRAINER
WATER PUMP
STRAINER
FLOW SWITCH (behind)
PRESSURE RELIEF VALVE (behind)
*IMMERSION
HEATER
MAIN REMOTE
CONTROLLER
FLOW SWITCH
MANOMETER
ADJUSTER
HANDLE
*Depending on model
127
P125-138.indd 127
13.12.12 1:25:39 PM
Designed for Optimal Heating
ZUBADAN New Generation (Split type)
Improved heating performance more efficiently
ZUBADAN is equipped with a unique “Flash Injection
Circuit” that enables the system to provide powerful
heating in cold regions during the winter months. And
more evolved “ZUBADAN New Generation” incorporates
a new compressor that is more efficient, further improving
heating performance when outdoor temperatures is low.
The rated heating capacity can now be maintained at
-15°C even including defrost, making it possible to supply
comfortable heating in ever more severe environments.
Approx. 22% higher than
Nominal capacity can be
kept at -15°C !
our previous model !
Integrated
capacity (kW)
15
ZUBADAN New Generation
14
13
12
11
10
ZUBADAN
9
-25°C
-20°C
-15°C
-7°C
0°C
Outdoor-air temperature at intake duct
W45 (according to EN 14511)
Max. possible
flow temp. (deg C)
65
A-15/W55
possible!
Ideal for
DHW!
ZUBADAN New Generation
60
55
50
45
40
-20°C
-15°C
-10°C
-5°C
-0°C
5°C
10°C
Outdoor temp.
Mitsubishi Electric’s Flash Injection Technology
The Key to High Heating Performance at Low Outdoor Temperatures
■ Flash Injection Circuit
ZUBADAN New Generation
Injection compressor
(injection port)
Indoor
HEX
Outdoor
HEX
Power
receiver
A
Heat Interchanger (HIC)
B
LEV A
LEV B
LEV C
Refrigerant
flow
Flash Injection Circuit
A
Heat
interchanger
(HIC)
B
Injection Compressor
Flash Injection Circuit
The Flash Injection Circuit is an original technology developed by Mitsubishi Electric. A heat exchange process at point A (heat interchanger)
transforms liquid refrigerant into a two-phase, gas-liquid state and then compresses the gas-liquid refrigerant at point B (injection compressor).
This circuit secures a enough flow rate of refrigerant for heating when outdoor temperatures are very low.
In the ZUBADAN New Generation, the Flash Injection Circuit is more powerful by improving the heat interchanger to increase the heatexchange-efficiency and incorporating new injection compressor to increase the compression-efficiency.
These two improvements of ZUBADAN New Generation ensure reliable, efficient heating operation when outdoor temperatures are very low.
128
P125-138.indd 128
13.12.12 1:25:39 PM
SD* CARD
*SD logo is a trademark of SD-3C, LLC
The ecodan evolution continues! For easier settings and for data loggings
Settings can be
performed using
an SD card.
Initial setting for ecodan is now simpler than ever before. The special software enables the required initial settings to be saved to an SD card
using a personal computer. System set-up is as easy as moving the SD card from the computer to the SD card slot in the indoor unit. Compared
to the previous procedure of inputting settings using the main controller at a installation field, a remarkable reduction in set-up time has been
achieved. Thus, it is ideal way for busy installers.
*SD card fanction is only used by installer.
Hydro box inside
Settings can be performed easily and
logging operation data in SD card
can be confirmed via personal computer.
Printed circuit board
Control and electric box
SD card slot
SD card
SD card
Items that can be preset
Data that can be stored
Simply copying the preset data to SD card,
same settings are complete in multiple units easily.
Operation data up to a month long can be stored on
a SD card (2GB) .
• Initial settings (time display, contact number, etc)
• Heating settings
- Auto Adaptation
- Heat curve
- Two different temperatures zones
• Interlocked boiler operation settings
• Holiday mode settings
• Schedule timer settings
• Domestic hot water settings
• Legionella prevention settings
• Operation time
• Defrost time
• Actual temperature
- Room
- Flow temperature
- Return temperature
- Domestic hot water temperature
- Outdoor temperature
• Error record
• Input signal
etc.
All items that are set by the main controller can be set via
a personal computer.
Remote controller
Stylish, easy-to-read bright LCD with ergonomically designed intuitive interface
Main controller
• Large screen and backlight for excellent visibility, even in dark environment
• Multilanguage support (11 languages)
• Can be removed from main unit and installed in remote location (up to 500m)
• Wide range of convenient functions in response to user demand
Functions settings
- Weekly timer -Holiday mode -Legionella prevention -Error codes and data for serving
NEW - Two zone control -Boiler interlock -Floor drying up
• Quick reading of operation data (7.5 times faster than previous model)
Main controller
Wireless remote controller (optional)
• Built-in room temperature sensor; easy to place in the best position to detect room temperature
• Wiring work eliminated
• Simple design that is easy to operate
• Remote control from any room without needing to choose an installation location
• Backlight and big buttons that are easy to operate
• Domestic hot water boost and cancellation
• Simplified holiday mode
• Up to 8 controllers allowed (can be set for zone 1 or 2 individually)
PAR-WR51R-E (optional)
Receiver
PAR-WT50R-E (optional)
Wireless remote controller
129
P125-138.indd 129
13.12.12 1:25:40 PM
Two zone control
Simultaneously making two different temperature zones
assures more comfortable, highly convenient heating
Settings can be
performed using
an SD card.
ecodan makes it possible to set two temperatures which are used in two different types heat emitters in a system. The system allows
adjustment of temperatures when different room temperatures are required, such as a temperature of 40°C for the living room radiator and
temperature of 30°C for floor heating. Additionally, the scheduling for each zone can be set separately by main controller.
■ Two temperature zones
40°C
Hydro box
Radiator
Pump
Mixing control
Mixing Flow switch
valve
FTC*
Pump
Mixing tank
*FTC = Flow temperature controller
30°C
Flow switch
Underfloor heating
*Items such as mixing tank, mixing valve, flow switch and pumps are not included and need to be purchased locally.
Intelligent boiler interlock
No need to replace existing boiler!
Automatic switchover enables even more efficient operation
Settings can be
performed using
an SD card.
The flexibility of ecodan’s intelligent control allows the system to be combined with boiler currently in use. Additionally, this control can judge
which heating source (ecodan, or boiler) to be operated according to situations (outdoor temperature, running cost, CO 2 emission level etc.).
Customers using a boiler can receive the energy-saving performance of ecodan.
Intelligent system combining a boiler with ecodan
Room temperature
wireless remote controller (option)
Hydro box
■ Two temperature zones
FTC
*Thermostat (field supply) also can be used.
Electricity
Other source
(Gas, Oil, etc)
Radiator
Radiator
Turning boiler on/off
according to operational
conditions.
Pump
Mixing tank
Boiler
*Items such as mixing tank and pump are not included and need to be purchased locally.
Multiple unit control
Connect up to 6 units
Automatic control of multiple units to supply bigger capacity
A maximum of 6 ecodan units* can be configured
according to the required heating/cooling load of the
building. The most efficient number of operating units is
determined automatically based on heating/cooling
load. This enables ecodan to provide optimal room
temperature control, and thus superior comfort for
room occupants. Also incorporated is a rotation function
that works to balance the running hours without
depending on the operation of any one specific unit.
If one of the units malfunctions when using Multiple
Unit Control, another unit can be automatically operated
for back-up, thereby preventing system operation from
stopping completely.
Settings can be
performed using
an SD card.
■ Multiple unit control
COP ratio (%)
1 unit
2 units
3 units
4 units
5 units
6 units
100
Always high efficient operation !
Inefficient operation
at low capacity.
ON/OFF control
Multiple unit control
One large unit control
Total Capacity
14 kW + 14 kW + 14 kW + 14 kW + 14 kW + 14 kW
FTC
FTC
FTC
FTC
FTC
FTC
slave
slave
slave
slave
slave
slave
*Only same models (same capacity) are available.
Multiple unit control
FTC
master
Main RC
130
P125-138.indd 130
13.12.12 1:25:41 PM
Split type specifications
Indoor unit
<Cylinder unit>
Model name
EHST20C-VM6HB EHST20C-YM9HB EHST20C-TM9HB EHST20C-VM2B EHST20C-VM6B EHST20C-YM9B EHST20C-VM6EB EHST20C-YM9EB EHST20C-VM6SB
Heating only
Type
Dimensions
Immersion heater
×
×
×
-
-
-
-
-
-
Expansion vessel
×
×
×
×
×
×
-
-
×
Solar circuit
-
-
-
-
-
-
-
-
×
128
128
128
125
127
122
122
128
1600×595×680
mm
H×W×D
Product weight (empty)
kg
Type of installation
127
Floor standing
-
Power supply (V / Phase / Hz)
Heater
Booster
heater
230/Single/50
230/Single/50
400/Three/50
230/Three/50
230/Single/50
230/Single/50
400/Three/50
230/Single/50
400/Three/50
230/Single/50
Capacity
kW
6 (2/4/6)
9 (3/6/9)
9 (3/6/9)
2
6 (2/4/6)
9 (3/6/9)
6 (2/4/6)
9 (3/6/9)
6 (2/4/6)
Current
A
26
13
23
9
26
13
26
13
26
Breaker
A
32
16
30
16
32
16
32
16
32
230/Single/50
230/Single/50
230/Single/50
-
-
-
-
-
-
3
3
3
-
-
-
-
-
-
Power supply (V / Phase / Hz)
Immersion Power supply (V / Phase / Hz)
heater
kW
Capacity
Domestic
hot water tank
Current
A
13
13
13
-
-
-
-
-
-
Breaker
A
16
16
16
-
-
-
-
-
-
Volume (net)
Material
Heating
200
-
Stainless steel
°C
0~35
Room temperature
°C
10~30
Flow temperature
°C
25~60
Operating ambient condition*
Target
temperature
range
L
DHW
°C
40~60
Legionella prevention
°C
Max 70
dB (A)
28
Sound level (SPL)
*The environment must be frost-free.
<Hydro box>
EHSC-VM2B
Model name
EHSC-VM6B
EHSC-YM9B
Expansion vessel
×
×
H×W×D
Dimensions
EHSC-TM9B
×
53
51
53
Power supply (V / Phase / Hz)
54
230/Single/50
230/Single/50
400/Three/50
230/Three/50
230/Single/50
400/Three/50
230/Single/50
Capacity
kW
2
6 (2/4/6)
9 (3/6/9)
9 (3/6/9)
6 (2/4/6)
9 (3/6/9)
2
Current
A
9
26
13
23
26
13
9
Breaker
A
16
32
16
32
32
16
16
0~35
0~35
0~35
0~35
0~35
0~35
0~35*2
-
-
N/A
-
-
5~25
Volume (net)
L
Material
Heating/
Cooling
49
230/Single/50
-
-
Operating ambient condition*1
Target
temperature
range
49
Wall mounted
Power supply (V / Phase / Hz)
Domestic
hot water tank
860×530×360
53
-
ERSC-VM2B
×
-
-
800×530×360
kg
Type of installation
Booster
heater
EHSC-YM9EB
Heating and Cooling
×
mm
Product weight (empty)
Heater
EHSC-VM6EB
Heating only
Type
-
°C
Room
temperature
Heating
°C
Cooling
°C
Flow
temperature
Heating
°C
Cooling
°C
10~30
-
-
-
-
-
-
25~60
-
DHW
°C
40~60
Legionella prevention
°C
Max 70
Sound level (SPL)
28
dB (A)
*1 The environment must be frost-free.
*2 Low outdoor temperature cooling is not allowed (minimum 10°C).
Outdoor unit
Model name
PUHZSHW80VHA
PUHZSHW112V/YHA
PUHZSHW140YHA
PUHZSHW230YKA*1 *2
mm
PUHZPUHZPUHZPUHZPUHZSW40VHA (-BS) SW50VHA (-BS) SW75VHA (-BS) SW100V/YHA (-BS) SW120V/YHA (-BS)
600×800×300
600×800×300
943×950×330
1350×950×330
1350×950×330
1350×950×330
1350×950×330
1350×950×330
1338×1050×330
kg
42
42
75
118 / 130
118 / 130
120
120/134
134
148
kW
4.10
6.00
8.00
11.20
14.00
23.00
4.80
4.42
4.40
4.45
4.10
4.65
4.46
4.22
3.65
Power input
kW
0.854
1.357
1.819
2.517
3.903
1.721
2.512
3.318
6.310
Capacity
kW
4.00
5.00
7.50
10.00
12.00
8.00
11.20
14.00
23.00
3.24
2.97
3.40
3.32
3.24
3.55
3.34
2.96
2.37
H×W×D
Dimensions
Product weight
VHA : 230/Single/50
Power supply (V / Phase / Hz)
Heating
(A7/W35)
Heating
(A2/W35)
Capacity
COP
COP
11.20
YHA : 400/Three/50
16.00
8.00
kW
1.235
1.684
2.206
3.009
3.704
2.254
3.354
4.730
9.690
Sound level (SPL)
Heating
dB (A)
45
46
51
54
54
51
52
52
59
Sound level (PWL)
Heating
dB (A)
62
63
69
70
72
69
70
70
76
Power input
Note: based on EN 14511 (Circulation pump input is not included.).
It may differ according to the system configuration.
*1 PUHZ-SHW230YKA can not be connected to ecodan indoor unit.
*2 The performance data is obtained when plate heat exchanger (ACH 70-40)×2 are connected.
131
P125-138.indd 131
13.12.12 1:25:42 PM
Optional parts
<Indoor unit>
Parts name
Model name
Specification
Cylinder unit
Hydro box
EHST20C- EHST20C- EHST20C- EHST20C- EHST20C- EHST20C- EHST20C- EHST20C- EHST20C- EHSC- EHSC- EHSC- EHSC- EHSC- EHSC- ERSCVM6HB YM9HB TM9HB VM2B VM6B YM9B VM6EB YM9EB VM6SB VM2B VM6B YM9B TM9B VM6EB YM9EB VM2B
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
For buffer and zone (flow and return temp.)
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
For tank temp.
-
-
-
-
-
-
-
-
-
×
×
×
×
×
×
×
PAC-TH011HT-E For boiler (flow and return temp.)
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Wirelss remote controller
PAR-WT50R-E
Wirelss receiver
PAR-WR51R-E
Thermistors
PAC-SE41TS-E
For room temp.
PAC-TH011-E
PAC-TH011TK-E
Immersion heater
PAC-IH03V-E
1Ph 3kW
Joint pipe
PAC-SH30RJ-E
For PUHZ-SW40/50VHA (-BS) ø9.52
PAC-SH50RJ-E
For PUHZ-SW40/50VHA (-BS) ø15.88
Wi-Fi INTERFACE
ø6.35
ø12.70
PAC-WF010-E
-
-
-
×
×
×
×
×
×
-
-
-
-
-
-
-
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
<Outdoor unit>
Parts name
Model name
Power inverter
ZUBADAN
PUHZPUHZPUHZPUHZPUHZPUHZPUHZPUHZPUHZSW40VHA(-BS) SW50VHA(-BS) SW75VHA(-BS) SW100V/YHA(-BS) SW120V/YHA(-BS) SHW80VHA SHW112V/YHA SHW140YHA SHW230YKA*1
Connector for drain hose heater signal output
PAC-SE60RA-E
×
×
×
×
Air discharge guide
PAC-SG58SG-E
×
×
-
-
-
-
-
-
-
PAC-SG59SG-E
-
-
×
×
×
×
×
×
-
PAC-SG96SG-E
-
-
-
-
-
-
-
-
×
PAC-SG56AG-E
×
×
-
-
-
-
-
-
PAC-SH63AG-E
-
-
×
×
×
×
×
×
-
PAC-SH95AG-E
-
-
-
-
-
-
-
-
×
PAC-SG61DS-E
-
-
×
×
×
-
-
-
-
PAC-SH71DS-E
×
×
-
-
-
-
-
-
-
PAC-SG63DP-E
×
×
-
-
-
-
-
-
-
PAC-SG64DP-E
-
-
×
×
×
-
-
-
-
PAC-SK52ST
×
×
×
×
×
×
×
×
×
Air protection guide
Drain socket
Centralised drain pan
Control / Service tool
×
×
×
×
×
-
*1 PUHZ-SHW230YKA can not be connected to ecodan indoor unit.
<Interface/Flow temperature controller>
Parts name
Model name
Description
Power inverter
ZUBADAN
PUHZPUHZPUHZPUHZPUHZPUHZPUHZPUHZPUHZSW40VHA(-BS) SW50VHA(-BS) SW75VHA(-BS) SW100V/YHA(-BS) SW120V/YHA(-BS) SHW80VHA SHW112V/YHA SHW140YHA SHW230YKA
Capacity step control interface
Flow temperature controllers
System controllers
PAC-IF010-E*1
10 PC boards w/o case
PAC-IF011B-E
× *2
× *2
× *2
× *2
×*2
× *2
× *2
× *2
× *2
1 PC board w/ case
×
×
×
×
×
×
×
×
×
PAC-IF020-E*1
10 PC boards w/o case
× *2
× *2
× *2
× *2
× *2
× *2
× *2
× *2
× *2
PAC-IF021B-E
1 PC board w/ case
×
×
×
×
×
×
×
×
×
PAC-IF032B-E
1 PC board w/ case
×
×
×
×
×
×
×
×
×
PAC-IF051B-E
1 PC board w/ case
×
×
×
×
×
×
×
×
×
PAC-SIF051B-E
1 PC board w/ case
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
PAC-TH011-E
Thermistors
*1 PAC-IF010-E and PAC-IF020-E are only for manufacturer’s preloading.
*2 PAC-TH011-E is required.
Contents
Parts name
Air discharge guide
Air discharge guide
Model name
PAC-SG58SG-E
PAC-SG59SG-E
PAC-SG96SG-E
Air protection guide
PAC-SG56AG-E
PAC-SH63AG-E
PAC-SH95AG-E
Drain socket
PAC-SG61DS-E
PAC-SH71DS-E
Contents
Air discharge guide
Support (For the upper and lower sides)
Support (For right and left)
Attachment screw (5×10)
Attachment screw (4×10)
Spacer
Air discharge guide
Attachment screw (5×35)
Spacer
Air discharge guide
Support
Screw (5×15)
Washer
Spring washer
Front plate
Side plate
Side plate
Connecting plate
Mounting screw (4×10)
Mounting screw (4×12)
Washer (for screw 4×12)
Air guide
Mounting screw (5×15)
Washer
Spring washer
Air guide
Mounting screw (5×15)
Washer
Spring washer
Drain socket
Drain cap (ø33)
Heat insulator
Band
Drain socket
Drain cap (ø33/ø12)
Heat insulator
Band
Q’ty
1
2
2
4
8
4
1
4
4
1
1
12
12
12
1
2
2
2
14
4
4
1
4
4
4
1
6
6
6
1
5
2
8
1
7
2
8
Parts name
Centralised drain pan
Control / Service tool
Capacity step control
interface
Model name
PAC-SG63DP-E
PAC-SG64DP-E
PAC-SK52ST
PAC-IF010-E
PAC-IF011B-E
Flow temperature
controllers
PAC-IF020-E
PAC-IF021B-E
PAC-IF032B-E
System controllers
PAC-IF051B-E
PAC-SIF051B-E
Thermistors
PAC-TH011-E
PAC-TH011HT-E
PAC-TH011TK-E
Contents
Centralised drain pan
Centralised drain pan
Control/Service Tool
PC board
PC board
Case
Thermistor
PC board
PC board
Case
Thermistor
Remote controller
Remote controller cable (5m)
PC board
Case
Thermistor
Remote controller
Remote controller cable (5m)
PC board
Case
Thermistor
Remote controller
Remote controller cable (10m)
SD memory card
PC board
Case
Thermistor
Remote controller cable (10m)
SD memory card
Thermistor for buffer and zone (flow and return temp.)
Thermistor for tank temp.
Thermistor for boiler (flow and return temp.)
Q’ty
1
1
1
10*1
1
1
2
10*1
1
1
2
1
1
1
1
3
1
1
1
1
2
1
1
1
1
1
2
1
1
20*2
20*2
10*3
*1 One carton contains 10 PC boards.
*2 Two thermistors per package: 10 packages per carton
*3 One thermistor per package: 10 packages per carton
132
P125-138.indd 132
13.12.12 1:25:43 PM
Packaged type specifications
Indoor unit
<Cylinder unit>
Model name
EHPT20X-VM2HB
EHPT20X-VM6HB
EHPT20X-YM9HB
Immersion heater
Expansion vessel
Dimensions
H×W×D
Product weight (empty)
×
×
×
×
×
×
115
113
115
Booster heater
Immersion heater
Domestic
hot water tank
-
-
×
×
×
115
114
114
230/Single/50
230/Single/50
230/Single/50
400/Three/50
230/Three/50
230/Single/50
400/Three/50
kW
2
6 (2/4/6)
9 (3/6/9)
9 (3/6/9)
6 (2/4/6)
9 (3/6/9)
Current
A
9
26
13
23
26
13
Breaker
A
16
32
16
30
32
16
230/Single/50
230/Single/50
230/Single/50
230/Single/50
-
-
Power supply (V / Phase / Hz)
Capacity
kW
3
3
3
3
-
-
Current
A
13
13
13
13
-
-
Breaker
A
16
16
16
16
-
-
Volume (net)
Material
Heating
×
Capacity
Power supply (V / Phase / Hz)
L
200
-
Stainless steel
°C
0~35
Room temperature
°C
10~30
Flow temperature
°C
25~60
Operating ambient condition*
Target
temperature
range
EHPT20X-YM9B
Floor standing
-
Power supply (V / Phase / Hz)
Heater
EHPT20X-VM6B
1600×595×680
mm
kg
Type of installation
EHPT20X-TM9HB
Heating only
Type
DHW
°C
40~60
Legionella prevention
°C
Max 70
dB (A)
28
Sound level (SPL)
*The environment must be frost-free.
<Hydro box>
EHPX-VM2B
Model name
EHPX-VM6B
×
Expansion vessel
Dimensions
H×W×D
Product weight (empty)
×
39
41
Domestic
hot water tank
Booster heater
230/Single/50
230/Single/50
400/Three/50
kW
2
6 (2/4/6)
9 (3/6/9)
Current
A
9
26
13
Breaker
A
16
32
16
Volume (net)
-
L
Material
Heating
230/Single/50
Capacity
Power supply (V / Phase / Hz)
-
-
Operating ambient condition*
Target
temperature
range
41
Wall mounted
-
Power supply (V / Phase / Hz)
Heater
×
800×530×360
mm
kg
Type of installation
EHPX-YM9B
Heating only
Type
°C
0~35
Room temperature
°C
10~30
Flow temperature
°C
25~60
DHW
°C
-
Legionella prevention
°C
-
dB (A)
28
Sound level (SPL)
*The environment must be frost-free.
Outdoor unit
Model name
PUHZW50VHA (-BS)
PUHZW85VHA2 (-BS)
mm
740×950×330
943×950×330
1350×1020×330
1350×1020×330
kg
64
79
148
134
kW
5.00
9.00
4.10
4.18
4.42
4.25
4.25
Power input
kW
1.220
2.153
2.533
3.294
3.294
Capacity
kW
5.00
8.50
11.20
14.00
14.00
3.13
3.17
3.11
3.11
3.11
kW
1.597
2.681
3.601
4.501
4.501
Heating
dB (A)
46
48
53
53
53
Sound level (PWL) Heating
dB (A)
61
66
67
67
67
H×W×D
Dimensions
Product weight
Power supply (V / Phase / Hz)
Heating
(A7/W35)
Heating
(A2/W35)
Capacity
Sound level (SPL)
VHA : 230/Single/50
COP
COP
Power input
PUHZPUHZPUHZHW112YHA2 (-BS) HW140VHA2 (-BS) HW140YHA2 (-BS)
1350×1020×330
148
YHA : 400/Three/50
11.20
14.00
14.00
Note: based on EN 14511 (Circulation pump input is included.).
It may differ according to the system configuration.
133
P125-138.indd 133
13.12.12 1:25:43 PM
Optional parts
<Indoor unit>
Parts name
Model name
Specification
Cylinder unit
Hydro box
EHPT20XVM2HB
EHPT20XVM6HB
EHPT20XYM9HB
EHPT20XTM9HB
EHPT20XVM6B
EHPT20XYM9B
EHPXVM2B
EHPXVM6B
EHPXYM9B
×
×
×
×
×
×
×
×
×
Wirelss remote controller
PAR-WT50R-E
Wirelss receiver
PAR-WR51R-E
×
×
×
×
×
×
×
×
×
Thermistors
PAC-SE41TS-E
For room temp.
×
×
×
×
×
×
×
×
×
PAC-TH011-E
For buffer and zone (flow and return temp.)
×
×
×
×
×
×
×
×
×
PAC-TH011TK-E
For tank temp.
-
-
-
-
-
-
×
×
×
PAC-TH011HT-E For boiler (flow and return temp.)
×
×
×
×
×
×
×
×
×
-
Immersion heater
PAC-IH03V-E
-
-
-
-
×
×
-
-
EHPT accessories for UK
PAC-WK01UK-E
×
-
-
-
-
-
-
-
-
Wi-Fi INTERFACE
PAC-WF010-E
×
×
×
×
×
×
×
×
×
1Ph 3kW
<Outdoor unit>
Parts name
Model name
Power inverter
ZUBADAN
PUHZW50VHA(-BS)
PUHZW85VHA2(-BS)
PUHZHW112YHA2(-BS)
PUHZHW140VHA2(-BS)
PUHZHW140YHA2(-BS)
Connector for drain hose heater signal output
PAC-SE60RA-E
×
×
×
×
×
Air discharge guide
PAC-SG59SG-E
×
×
×
×
×
Air protection guide
PAC-SH63AG-E
×
×
×
×
×
Drain socket
PAC-SG61DS-E
×
×
-
-
-
Centralised drain pan
PAC-SG64DP-E
×
×
-
-
-
PUHZW85VHA2(-BS)
PUHZHW112YHA2(-BS)
PUHZHW140VHA2(-BS)
<Interface/Flow temperature control>
Parts name
Model name
Description
Power inverter
PUHZW50VHA(-BS)
Capacity step control interface
Flow temperature controllers
System controllers
PUHZHW140YHA2(-BS)
PAC-IF010-E*1
10 PC boards w/o case
× *2
× *2
× *2
× *2
× *2
PAC-IF011B-E
1 PC board w/ case
×
×
×
×
×
PAC-IF020-E*1
10 PC boards w/o case
× *2
× *2
× *2
× *2
× *2
PAC-IF021B-E
1 PC board w/ case
×
×
×
×
×
PAC-IF032B-E
1 PC board w/ case
×
×
×
×
×
PAC-IF051B-E
1 PC board w/ case
×
×
×
×
×
PAC-SIF051B-E
1 PC board w/ case
×
×
×
×
×
×
×
×
×
×
PAC-TH011-E
Thermistors
ZUBADAN
*1 PAC-IF010-E and PAC-IF020-E are only for manufacturer’s preloading.
*2 PAC-TH011-E is required.
Contents
Parts name
Model name
Contents
Air discharge guide
PAC-SG59SG-E
Air discharge guide
1
Attachment screw (5×35)
4
Spacer
Air protection guide
Drain socket
PAC-SH63AG-E
PAC-SG61DS-E
Q’ty
Parts name
Model name
Contents
Q’ty
System controllers
PAC-IF051B-E
PC board
1
Case
1
4
Thermistor
2
Air guide
1
Remote controller
1
Mounting screw (5×15)
4
Remote controller cable (10m)
1
Washer
4
SD memory card
1
Spring washer
4
PC board
1
Drain socket
1
Case
1
Drain cap (ø33)
5
Thermistor
2
Heat insulator
2
Remote controller cable (10m)
1
Band
8
SD memory card
Centralised drain pan
PAC-SG64DP-E
Centralised drain pan
Capacity step control
interface
PAC-IF010-E
PC board
10*1
PAC-IF011B-E
PC board
1
Case
1
Thermistor
Flow temperature
controllers
1
2
10*1
PAC-IF020-E
PC board
PAC-IF021B-E
PC board
1
Case
1
Thermistor
2
Remote controller
1
Remote controller cable (5m)
1
PC board
1
Case
1
Thermistor
3
Remote controller
1
Remote controller cable (5m)
1
PAC-IF032B-E
PAC-SIF051B-E
Thermistors
1
PAC-TH011-E
Thermistor for buffer and zone (flow and return temp.)
20*2
PAC-TH011HT-E
Thermistor for tank temp.
20*2
PAC-TH011TK-E
Thermistor for boiler (flow and return temp.)
10*3
*1 One carton contains 10 PC boards.
*2 Two thermistors per package: 10 packages per carton
*3 One thermistor per package: 10 packages per carton
134
P125-138.indd 134
13.12.12 1:25:43 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement