DPA | 4021 | 4021 / 4022 / 4023 / 4026 / 4027 / 4028

4021 / 4022 / 4023 / 4026 / 4027 / 4028
U S E R’S MAN UA L
Compact Cardioid Microphones
Type
402 1
Type
4022
Type
4023
Compact Wide Cardioid Microphones
Type
4026
Type
4027
Type
4028
Included in kit solutions:
Type
352 1
CO N T E N TS
Technical Description
Care of Microphones
Full Specifications
Service and Repair
Warranty
CE Standard
3
9
12
16
16
16
1
4021 & 4027
4022 & 4026
4023 & 4028
2
T E C H N I CAL D ESC RI PT I O N
The cartridge
Types 4021, 4022, 4023, 4026, 4027 and 4028 are Cardioid
(Pressure gradient) microphones that use the same microphone
capsule as the s tandard microphones Types 4011, 4012, 4015 and
4016. The Compact Cardioid Microphones use a 19mm diameter
prepolarized pressure gradient condenser microphone cartridge.
Type 4021, 4022 and 4023 offer a first order cardioid pick-up pattern, the Type 4026, 4027 and 4028 offer a wide cardioid pattern
(see Fig. 2 & 3).
The diaphragm is highly resis tant to the most aggressive kinds of
humidity. The large spacing between the diaphragm and the back
plate in this cartridge makes the microphone highly insensitive to
temperature influence and allows greater SPL handling before
clipping occurs.
Type 4021, 4022 and 4023 are designed to have a linear on-axis
response from 40Hz to 20kHz (±2dB) measured at 30cm distance
(see Fig. 4). Type 4026, 4027 and 4028 are designed to have a
linear on-axis response from 40Hz (±2dB) to 20kHz (+3/-1dB) measured at 60cm dis tance (see Fig. 5) and are fur thermore intentionally
calibrated with a slight high-frequency soft boost.Great attention
has also been paid to the microphone’s off-axis performance during
the design process (see Fig. 4 & 5 ).
The diaphragm is protected from dust by an acoustically transparent
net behind the front protection grid and inside the back port of the
cartridge. For optimum stability the microphone cartridge has
undergone a special pre-aging process, which s tabilizes all tensions
in the materials as well as the polarization voltage.
The preamplifier
The Compact Cardioid and Compact Wide Cardioid Microphones use
built-in ultra-small, thick-film preamplifiers with unity-gain, low noise
FET-amplifier technology. The thick-film technology enables the
microphone cartridge to be mounted on an exceptionally compact
microphone housing with the preamplifier mounted directly behind
the microphone cartridge. A circuit of passive components in the
standard 3-pin XLR connector adapts the P48 phantom powering,
separates the supply voltage from the audio signal and acts as an
3
impedance balancing circuit for optimum noise immunity. The preamplifier has a cable drive capability of up to 100 m after the XLRconnector (See Fig. 1 for pin designation).
All microphones come with an individual calibration chart of the
selfnoise, sensitivity and the individual frequency response.
The mechanical design
Types 4021, 4022 and 4023 are acoustically identical as are the
4026, 4027 and 4028. They only differ in their mechanical design.
All Compact Cardioid Microphones are delivered with 5m of
extremely flexible, high quality microphone cable as standard.
The 4021 and 4027 cable is side-mounted on the microphone and
the 4022 and 4026 cable is rear-mounted. The 4023 and 4028 feature a triaxial Lemo-connector, for simple and safe attachment
mounting of the microphones to DPA Compact Active Poles.
Important: The microphones will only operate within their
specifications if powered correctly.
Fig. 1. External view
of the output socket
of the standard 3-pin
XLR-connector used
in the Types 4021,
4022, 4023, 4026,
4027 and 4028.
4
Fig. 2. Directional characteristics of Types 4021, 4022 and 4023.
Shifts between emphasized circles indicate 10dB steps
Fig. 3. Directional characteristics of Types 4026, 4027 and 4028.
Shifts between emphasized circles indicate 5dB steps
5
Fig. 4. On-and off-axis responses of Types 4021, 4022 and 4023
measured at 30cm.
Fig.5 On-and off-axis responses of Types 4026, 4027 and 4028
measured at 60cm.
6
Fig. 6. The proximity effect exhibited by the Types 402 1, 4022
and 4023.
Fig. 7. The proximity effect exhibited by the Types 4026, 4027
and 4028.
7
Fig. 8. On-axis amplitude and phase responses of Types 402 1, 4022,
4023, 4026, 4027 and 4028 plotted using a linear frequency axis
for evaluation of the phase response.
8
CAR E OF M ICRO P H O N E S
It is important to bear in mind the following points with regards to
mounting, microphone care and the use of accessories:
The microphone car tridge is tightly secured to the main body
housing. No attempt should be made to remo ve it. If a replacement
cartridge is required, contact your local DPA Microphones
representative.
Use of windscreen is recommended when microphones are used
in dirty or dusty environments.
When not in use, the microphone should be disconnected and
kept in the case supplied.
The Compact Series Microphones are delivered in a rugged case
together with a reel for the cable. Inside the reel there is room for
both the microphone and the XLR-connector for maximum protection. When packing the microphones, fir st place the microphone
and the XLR-connector inside the reel, then roll up the cable.
The Compact Series Microphones are delivered together with the
SM4000 Suspension Mount for applications where the microphones need to be suspended from their own cable. To position
the microphone you can bend and rotate the SM4000.
9
First place the microphone and the XLR-connector inside the reel,
then roll up the cable.
10
Correct placement of the SM4000 on a DPA 4021 or 4027.
11
FUL L SP ECIF ICAT I O N S
Cartridge type:
4021, 4022 and 4023: Pre-polarized condenser Type DMM0056
4026, 4027 and 4028: Pre-polarized condenser Type DMM0058
Principle of operation:
Pressure gradient
Power Supply:
Phantom P48
Frequency range:
4021, 4022 and 4023: On-axis: 40Hz to 20kHz ±2dB at 30 cm
4026, 4027 and 4028: On-axis: 40Hz ±2dB to 20kHz +3/-1dB
at 60 cm with a max. 3 dB soft boost at 10 – 15 kHz.
Phase response:
Phase matching between any two microphones: ±15°
(100Hz to 20kHz)
Directional characteristics:
4021, 4022 and 4023: Fir st order cardioid
4026, 4027 and 4028: Wide cardioid
Sensitivity:
Nominally 7mV/Pa (at 1kHz)
Equivalent noise level A-weighted:
Typ. 20dB(A) re. 20µPa
Equivalent noise level CCIR 468-1:
Typ. 25dB (max. 28dB)
Max SPL before clipping occurs:
145dB SPL peak
Total Harmonic Distortion:
110 dB SPL peak (<0.5% THD)
Preamplifier:
Output impedance:
<300 Ohm
Cable drive capability:
Up to 100m
Difference frequency distortion:
(DF2, DF3, Df = 70Hz) <0.5% at 110dB SPL peak
12
Influence of vibration:
<71dB equivalent SPL for 1m/s2 in direction of greatest
sensitivity
Influence of magnetic field:
45dB equivalent SPL for 80A/m, 50Hz in direction of greatest
sensitivity
Operating temperature range:
-10 to +55°C (+14 to 131°F)
Dimensions:
Microphone length:
4021 and 4027: 31mm
4022 and 4026: 35mm; 52mm incl. cable relief
4023 and 4028: 30 mm; 71mm incl. connector
Microphone diameter:
19mm
Capsule diameter:
19mm
Weight:
4021 and 4027: 27.5g (without cable)
4022 and 4026: 30g (without cable)
4023 and 4028: 33g (without cable)
ACC E SSO RIE S IN CLU D E D
Microphone Holders & Suspension Mounts
SM4000
DUA0020
Suspension Mount
Small Windscreen for Ø19mm Microphone
13
ACC E SSORIE S AVA I LA B L E
Microphone Holders for Musical Instruments
CH4000
GM4000
MB4000
SAX4000
VH4000
Microphone Holder for Cello
Gooseneck Mount, 19mm
Magnet Base
Microphone Holder for Saxophone and Hor n
Microphone Holder for Violin and Bass
Shock Mounts
CSM4000
TSM4000
UA0897
Compact Shock Mount
Table Shock Mount
Shock Mount
Shock Mount Rubbers
DDS0019
Rubber Mount 19mm, Extra Soft
Stereo Accessories
CXO4000
CXY4000
EXY4000
UA0837
Compact XY and ORTF Stereo Holder
Compact XY Stereo Holder
Extension for Compact Stereo Holders
Stereo Boom excluding Holders
Floor & Table Stands
CAP0400
CAP0750
CAP1250
DUA0100
DUA0250
DUA0500
FGS4000
FGT4000
FJS4000
SJD4000
SJS4000
TB4000
Compact Active Pole, 400mm
Compact Active Pole, 750mm
Compact Active Pole, 1250mm
Stand Extension, 100mm
Floor Base, Ø250mm
Stand Extension, 500mm
Flamingo Grand, Single Stand
Flamingo Grand Twin, Double Stand
Flamingo Junior, Short Single Stand
Swivel Joint, Double
Swivel Joint, Single
Table Base
Windscreens
DUA0022
14
Twin Windscreen for Ø19mm Microphone
3521 : COM PAC T CAR DIO ID STE REO KIT, P48
Professional Piano Miking Solution
The 3521 is a complete stereo kit with two 4021 Compact Cardioid
Microphones carefully matched within 2dB on frequency response,
sensitivity and self-noise. Complete with accessories, this kit is
designed especially for low profile mounting directly inside a piano.
With the XY/ORTF holder, the kit is also exceptional as a compact
stereo pair for applications such as overhead for drums, horn or
string sections, choirs, main or additional spot pair for small or big
acoustic ensembles.
The complete kit is supplied in a sturdy car rying case and includes
the combination XY/ORTF holder, 2 gooseneck mounts and 2 mag net bases for mounting on metal surfaces.
3521 KIT I NC LU D E S
2 x 4021
2 x GM4000
2 x MB4000
1 x CXO4000
Compact Cardioid Microphone (matched)
Gooseneck Mount, 19mm (0.75in)
Magnet Base
Compact XY and ORTF holder
15
S E RV IC E & REPA I R
Products from DPA Microphones are extremely stable, and there
should not be any significant change in the specifications with time
and use. If, however, you are not totally satisfied with the characteristics exhibited by these products, contact your nearest DPA
Microphones representative for fur ther details of service and the
repair facilities that are available. DPA Microphones has a maximum
seven working days in-house service policy, usually ensuring that no
more than seven working days will elapse from the day the item for
service is received and accepted to the day we are ready to return
it to you. Please contact DPA Microphones for your nearest representative on
Tel: +45 48 14 28 28
Fax:+45 48 14 27 00
You can also get in touch with DPA Microphones via the internet
using e-mail info@dpamicrophones.com
Visit our website at www.dpamicrophones.com
WA R R A N TY
All products from DPA Microphones are covered by a two-year
limited warranty on both mechanical functionality and documented
specifications as long as the items are not mistreated, abused or
modified in any way. In case of a warranty claim your invoice is your
warranty registration.
C E STA N DA R D
The CE-mark guarantees all products conform to relevant
standards approved by the European Community. The products
described in this User’s Manual comply with current relevant
standards when used with cables from DPA Microphones. EMC
Directive: 89/336/EEC, amended by 92/31/EEC and 93/68/EEC
Low Voltage Directive: 73/23/EEC, amended by 93/68/EEC
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising