Raritan | Marine Elegance Toilet | Specifications | Raritan Marine Elegance Toilet Specifications

Raritan Marine Elegance Toilet Specifications
ATLANTES FREEDOMTM TOILET
TM
VORTEX-VAC
Installation and Maintenance Instructions
MODEL AV
THE FOLLOWING ARE CAUTIONARY STATEMENTS THAT MUST BE READ AND
FOLLOWED DURING BOTH INSTALLATION AND OPERATION.
WARNING: Raritan Engineering Company, Inc. recommends that a qualified person or electrician install
this product. Equipment damage, injury to personnel or death could result from improper
installation. Raritan Engineering Company, Inc. accepts no responsibility or liability for
damage to equipment, injury or death to personnel that may result from improper installation
or operation of this product.
WARNING: HAZARD OF SHOCK OR FIRE
Always use recommended fuse, circuit breaker and wire size.
Motors used with this product are “Ignition Protected”. They are not however, explosionproof as defined in 46CFR 110.15-65(e), Subchapter J-Electrical Engineering.
DO NOT run continuously for more than 30 seconds.
Pressurized
Freshwater Model
Description:
Atlantes Freedom Vortex-Vac toilet is available in 12V
or 24V DC. Bowls are available in two bowl style:
household and elongated size bowl. Both models are
available in two color choice: White and
Almond(bone). Fresh water model utilizes onboard
pressurized freshwater and sea water model utilizes a
remote pump installed between raw water source and
bowl.
Sea/Fresh model allows switching between fresh and
raw water source.
Three different control options are available
1. Momentary Handle Control: provides
momentary operation of flush water and
discharge.
2. Smart Toilet Control: provides timed operation
and independent control of flush water and
discharge with handle or wall switch.
2. Multifunction Momentary (Vimar )Toilet
Control: provides momentary operation and
independent momentary control of flush water and
discharge
Sea Water Model
(Remote Pump)
1
SAFETY
IMPORTANT SAFETY INSTRUCTIONS:
WARNING:
HAZARD OF FLOODING - Always shut off seacock(s) before leaving the boat unattended.
Double clamp all below waterline hose fittings and check frequently for integrity.
Toilets mounted at or below the waterline must have
a vented loop installed in the discharge line. The top
of the vented loop must be a minimum of 4" (10cm)
above the waterline at the boats greatest angle of
heel (see vented loop manufacturer’s instructions).
Sea Water Models must also have a vented loop
installed between the intake pump and the toilet bowl.
Double clamp all below waterline connections.
WARNING:
Young children should NOT be left unsupervised
around toilet. Serious injury or death could occur.
Children can drown in water retained in th bowl.
Seat and/or lid could close and strike child.
Always replace circuit breaker and fuses with same
rating . Use Raritan parts to maintain ignition
protection requirements.
Recommended Visual Inspection
3
3
3
3
3
3
•
•
For leaks at toilet and hose connections
Hose clamps
•
Condition of hoses
Seacocks
Condition of wires and connections
•
In-Line Strainer (if you have one)
2
No special toilet paper is required.
Water should appear in the bowl within ten
seconds. If not, see troubleshooting section.
Hard objects or stringy substances (paper towels,
feminine hygiene products, filter cigarettes, etc.)
must not be thrown into the toilet as they will cause
damage.
Always shut off seacock(s) before leaving the boat
unattended.
Parts Required
3/4" (19 mm.) I.D. intake hose approximately 3 feet
(1 m.) long.
1" (25 mm.) or 1 1/2" (38 mm.) I.D. discharge hose
approximately 3 feet (1 m.) long.
Two buckets
Nontoxic antifreeze approximately 1 quart (1 liter)
Steps
1. Close the intake and discharge seacocks.
2. Turn off power to unit.
3. Disconnect and drain pump suction hose and toilet
discharge hose .
4. Connect short hoses to pump’s suction intake and
to toilet discharge.
5. Place one empty bucket under hose connected to
toilet’s discharge.
6. Pour nontoxic antifreeze in other bucket.
7. Place hose connected to intake pump into bucket
with antifreeze.
8. Turn on power to unit and flush toilet until
antifreeze begins to be discharged from toilet.
9. Disconnect power from toilet.
Please see instructions included with control
to see how to operate your unit
Winterizing:
•
•
•
•
•
Improper winter lay up is a major cause of marine
toilet failure.
Use only nontoxic antifreeze.
Flush toilet several times to clear waste from
system.
Dispose of all antifreeze in accordance with local
and federal regulations.
Winterize holding tanks, plumbing, treatment
systems (MSD’s), etc. independently following
manufacturer’s instructions.
Pressurized Freshwater Models
Parts Required
• 1" (25 mm.) or 1 1/2" (38 mm.) I.D.
discharge hose, approximately 3 feet (1 m.) long
• Two buckets
• Nontoxic antifreeze approximately 1 quart
(1 liter)
Steps
1. Close discharge seacock (if one exists).
2. Shut off intake water at source.
3. Turn off power to unit.
4. Disconnect and drain intake and discharge hose.
5. Disconnect intake hoses from toiletand place in
one of the buckets.
6. Connect short hose to toilet’s discharge and place
in other bucket.
7. Pour antifreeze in bowl.
8. Turn on power to unit and flush until antifreeze is
removed from the bowl and water is drained from
the solenoid and hose.
9. Disconnect power to toilet.
10. Reconnect intake hoses to water solenoid
RECOMMISSIONING
1. Using the buckets, hoses and approximately one
gallon (3.8 liters) of clean fresh water, flush
antifreeze out of the toilet (see Winterizing).
Dispose of antifreeze in accordance with local
and federal regulations.
2. Reconnect the intake and discharge hoses and
open both seacocks and water source valve.
3. Check all connections for leaks with several test
flushes.
SYSTEM START-UP
1. Open seacock(s).
NOTE: Pressurized freshwater models; open water
source valve.
2. Turn on power to toilet.
3. Flush toilet per Operation Instructions.
4. Check for leaks.
3
IMPORTANT: If toilet does not flush properly
or if water does not enter the bowl within 10
seconds, refer to Troubleshooting.
WINTERIZING
Intake Pump Models
Operation:
SPECIFICATIONS
Plumbing
CONVERSIONS
Maximum suction of Intake pump
(Maximum height above waterline)
Wire - AWG to mm2
4 Ft. (1.2m) from Intake Pump.
A WG
16
14
12
10
8
6
4
2
mm2
1.5
2.5
4.0
6.0
10.0
16.0
25.0
35.0
Maximum height of discharge vented loop 10 Ft. (3 m) from base of toilet.
Minimum fLow rate 3 gallons
(11.3 liters )per minutes, Minimum
Pressure 5 PSI(34.5 Kpa)
Pressurized water source minimum
requirements
Feet to Meters
NOTES: for Wiring
1.
Distances are from source to unit and back to source.
2.
Distance from power source to remote intake pump MUST be included when
determining total distance.Same wire size MUST be used for lower base and
remote intake pump.
3.
Recommended conductor wire minimum AWG (mm2) for 3% voltage drop.
4.
Recommended conductor sizes are based on 105oC rated insulation.
Refer to ABYC Standards for other insulation ratings.
5.
For 120/240 VAC units use 12VDC specifications from transformer to unit.
Feet
10
15
20
25
30
40
50
Met er
3.1
4.6
6.1
7.6
9.2
12.2
15.2
Hose Sizes
INLET
1/2”(12.7 mm.) for freshwater model
3/4” (19 mm.) for sea water model
Discharge
1”(25.4 mm.) or 1 1/2”(38 mm.)
Sea Water Model - Recommended Wire and Fuse/Circuit Breaker Size
D ischarge
pump
R emote
Pump
Only
U nits
Voltage
C ircuit
B reaker/fuse
size (amps)
A mp. draw
@ nominal
Voltage/
12 V D C
30
18
10
10 AWG 8 AWG
6 AWG
6 AWG
4 AWG
24 V D C
20
10
5
14 AWG 14 AWG
12 AWG
10 AWG
10 AWG
15
feet
A mp. draw
@ nominal
voltage
20
feet
30
feet
40
feet
50
feet
Pressurized Freshwater Model - Recommended Wire and Fuse/Circuit Breaker Size
Units
Voltage
Circuit
Breaker/fuse
size (amps)
Amp. draw
@ nominal
voltage
12 VDC
25
18
24 VDC
15
10
10
feet
15
feet
20
feet
12 AWG
10 AWG
10 AWG
8 AWG
6 AWG
6 AWG
14 AWG
12 AWG
10 AWG
10 AWG
8 AWG
6 AWG
WIRING:
FOLLOW THE
INSTRUCTIONS
INCLUDED WITH
CONTROL
30
feet
40
feet
50
feet
SIZE
See Table
next page
Water Consumtion:
water saver : 2 pint*
Regular Flush: 2 quarts
* requires timing adjustment
4
Additional Parts Required
• Two stainless steel mounting bolts or lag screws
(minimum 1/4" [6mm]) and washers)
• 1" (25 mm.) or 1 1/2" (38 mm.) I.D. discharge hose
• 3/4" (19 mm.) I.D. reinforced intake hose
• 3/4" (19 mm.) and 1" (25 mm.) or 1 1/2" (38 mm.)
hose clamps (two for each connection below
waterline)
• Wire
• Terminals
• Fuse/circuit breaker
1. Toilet bowl assembly
2. Mounting hardware
3. Seat
4. One of the following flush controls:
a. Flush handle control
b. Multifunction Momentary Control(Vimar)
c. Smart Toilet Control
5. User guides and Installation guides with labels
Additional Parts included with sea
water model:
1. Remote pump assy.
Atlantes discharge Maximum recommended 1” or 1 1/2” PVC hose length
14
NOTE:
1. Each 90 degree Elbow is equal to 4 feet of hose
2. Each insert coupling is equal to 2 feet of hose
3. Each Y-valve is equal to 10 feet of hose
Example: An installation has 50' of straight run with two elbow and a
Y- valve, what is maximum height of loop allowed?
Answer: equivalent hose length = 50' +8'(two elbows)+10'(Y-valve)
= 68'
From chart horizontal distance of 68' gives a vertical dist. @ 7'
Hence a maximum of 7' high loop can be installed.
12
10
Vertical height (Feet)
8
6
4
2
0
0
20
40
60
80
100
120
140
160
180
Horizontal distance (Feet)
SIZE
Inches
(mm)
B ow ltype
A
B
C
D
E
F
H ousehold
19 1/4
( 489)
15
( 381)
17
( 432)
15
( 381)
14 3/8
( 355)
14
( 355)
E longated
21 1/2
( 545)
18 1/4
( 455)
17
( 432)
15
( 381)
14 1/8
( 359)
14
( 355)
5
SPECIFICATIONS
Parts included with all models
MOUNTING
Mounting Toilet
Mounting surface must be flat and solid.
1. Install seat on toilet.
2. Place toilet where it will be located.
Make sure there is room to route hoses.
Make sure seat will open properly.
3. Using a pencil, mark location of bowl
mounting holes.
4. A. If hoses will be routed through floor, trace
one side of toilet on floor.
B. If hoses will be routed through wall, trace
one side of toilet on wall.
5. Remove toilet and mark location for hoses on
deck or wall.
6. Cut necessary holes using enclosed template
through wall or floor.
7. Drill holes for toilet mounting bolts/screws.
NOTE: Use 1/4" [6mm] size bolts/screws. To
select proper Screw or Bolt length, measure
thickness of deck plus 1 1/8'' (29mm).
TIP: Do not install until all wiring and plumbing
is done. Secure toilet to floor after installation is
complete.(see page 9)
CAUTION: Do Not over tighten mounting
bolts. Damage to the toilet bowl may occur.
Tighten both mounting bolts evenly and
slowly.
Mounting Remote Pump:
1. Locate remote pump between thru hull fitting
and toilet bowl.
2. Locate in an area away from berth to keep
noise level down.
3. Use Inline Strainer part# 163000 (optional) to
avoid clogs.
4. Secure remote pump to the floor using four
bolts through the pump base.
TO INSTALL HOLDING TANK FULL
SENSOR , REFER TO MANUAL WITH
HOLDING TANK FULL SENSOR.
6
WARNING: Hazard of Flooding
Toilets mounted at or below the waterline must
have a vented loop installed in the discharge line.
The top of the vented loop must be a minimum of
4" (10 cm.) above the waterline at the boats
greatest angle of heel (see vented loop
manufacturer’s instructions).
Discharge
Waterline
Holding Tank
Shut off
Valve
Pressurized Freshwater Model
Installed Above/below Waterline
Sea Water Models must also have a vented loop
installed between the intake pump and the toilet bowl.
Waterline
Pressurized
Freshwater
Source
Double clamp all below-waterline connections.
IMPORTANT
•
•
•
•
•
•
Fittings and 90° bends should be kept to a
minimum.
In-Line Strainer may be installed on Sea Water
Models per Installation Instructions. This will
prevent clogs.
Discharging untreated sewage is forbidden in all
U. S. waters within the three-mile limit.
Thru-hull fittings and seacocks must be installed
where they are easily accessible.
Use only quality reinforced hoses such as Raritan
SANIFLEX (part# SFH).
Secure all hoses properly.
Waterline
Waterline
Electroscan
Pressurized Freshwater Model
Installed below Waterline
Discharge
Seacock
Discharge
Vented
Loop
Holding
Tank
Discharge Lines
1. Connect quality sanitation hose 1" (25 mm.) or 1 1/
2”(38 mm.) discharge fitting on toilet.
2. Run hose to appropriate device (i.e.: treatment
system, holding tank, etc.).
Intake
Seacock
remote
pump
Electroscan
Discharge
Seacock
Remote Pump Model Mounted above Waterline
Inlet lines
1. Connect 1/2”(13 mm.) hose to pressurized supply
or 3/4”(19 mm.) hose to remote pump
Inlet Vented
Loop
Discharge
Vented
Loop
Electroscan
Intake
Seacock
Discharge
Seacock
remote pump
Remote Pump Model Mounted below Waterline
7
PLUMBING
PLUMBING
PLUMBING
Intake Lines
Pressurized Freshwater Models
Install a shut off valve in intake line before water solenoid
valve.
1. Connect hose from shut off valve to inlet port of
water solenoid valve at the toilet.
NOTE: To avoid malfunction of water solenoid due to
debris in water, installation of Freshwater Strainer
(190601) is recommended.
Remote Sea Water Models
Intake pump fittings are interchangeable to allow more
flexibility during installation. Inlet ports are located on
either side of intake pump. Outlet port (to toilet bowl) is
at top of intake pump.
NOTE: To avoid poor pump performance installation
of strainer (163000) is recommended
1. Slide fitting clips to open position.
2. Select inlet port to be used.
3. Install appropriate fittings into inlet and outlet ports.
NOTE: The 90° fitting can be rotated 360°.
4. Install the plug fitting into unused inlet port.
To Bowl
Connecting Hoses and wiring to toilet
1. Route wire from control per control instruction.
2. Install seat. Install discharge support strap
between seat nut and the bowl per below.
3. Install toilet in place, connect hoses and wireplugs.
(see Fig.)
Caution: Do not pull on the discharge hose to
avoid kinking
8
Arrow
From
Strainer
IMPORTANT: Be sure not to install plug fitting
into outlet port! Damage to pump will occur!
5. Slide fitting clips back to closed position.
6. Connect hose from seacock to inlet port of optional
In-Line Strainer if installed. Use hose clamp
provided.
7. Connect hose from outlet port of In-Line Strainer to
inlet port of intake pump. Use hose clamp provided.
IMPORTANT: Double clamp all below waterline
hose connections!
8. Connect hose from outlet port of intake pump to
bowl elbow located on back of toilet bowl.
CLIP MUST BE FULLY
SEATED IN CLOSED
POSITION
Outlet Port
Open
Plug
From
Seacock
Inlet Ports
To Intake
Pump
1 Install mounting bushings, bolts. (See Fig.)
2. Tighten bolts being careful to not overtighten
(Do not exceed 30 inch lb. when tightening)
3. Install caps over mounting bolts.
A
B
C
D
C
E
F
A. Vinyl cap - #VCap (supplied)
B. 1/4-20 S/S Bolt, or 1/4 S/S
Self Tapping Screw, or 1/4
S/S Lag bolt
C. Flat Washer, Stainless Steel
D. Nylon Shoulder Washer #F071 (supplied)
E. S/S Lock washer (used on
top and bottom for Nut and
Bolt)
F. 1/4-20 S/S Nut
TROUBLESHOOTING
WARNING:
HAZARD OF ELECTRIC SHOCK - Before beginning any work on the toilet, be sure that all power
to the unit has been turned off.
WARNING: HAZARD OF FLOODING - Make sure seacocks are in the CLOSED or OFF position before working on toilet.
NOTE:
The following information reflects the most probable causes and solutions to problems although not
every possible cause and solution is provided.
Any questions regarding servicing or operation of the Marine Elegance should be directed to our Technical Support
Department in Millville, NJ or Ft. Lauderdale, FL. Please have model and serial number available before calling.
PROBLEM
1. Poor pumpout, especially
solids.
SOLUTION
POSSIBLE CAUSE
1A. Be sure discharge seacock is open. Clear line, remove
clog.
Plumbing restrictions, bends and ells. 1B. Replumb to eliminate bends and ells.
1C. Clean holding tank vent and vented loop vents
Clogged vents.
Mineral buildup in hoses and fittings. 1D. Clean or replace affected parts. Replace hose if needed.
1E. Check voltage at toilet while toilet is running. If
Low voltage.
less than nominal voltage of toilet (12 or 24), check
condition of batteries and wire sizes. Check terminals
and wire connections for corrosion (heat at terminals
and junctions indicates a bad or corroded connection).
1A. Clogged discharge line.
1B.
1C.
1D.
1E.
2. Poor water flow, especially
at front of bowl (or no water flow).
2A. Toilet not level.
2B. Restriction in intake line.
2C. Pump sucking air.
3. Foul odors from toilet area.
2D.
2E.
3A.
3B.
3C.
4. Bowl fills while underway.
4A.
5. Water leaking from under
unit.
5A.
5B.
5C.
2A. Raise rear of toilet; check with level.
2B. Be sure seacock is open. Clear line-remove clog.
2C. Check all connections from intake thru-hull to intake
pump to be sure no air leaks are present.
2D. See 1E, above.
Low voltage.
2E. Remove or Clear debris from strainer.
Clogged strainer.
“Marine life” lodged in rim of bowl. 3A. Remove and flush bowl with pressure hose to remove
all material. Install strainer in intake line to avoid recurrence.
3B. Replace hose with Raritan sanitation hose (#SH).
Permeated discharge hose.
Sewage remaining in discharge line. 3C. Flush toilet longer; replace hose if permeated; reroute
hose making a shorter run if possible.
4A. Close intake, then discharge seacock to determine
Pressure buildup at seacocks.
which is causing problem. If discharge, be sure the
vent or vented loop is clean. If intake, there is too
much pressure on seacock; contact Raritan Technical
Support.
5A. Tighten adapter clamps.
Leaking Bowl Throat adapter.
5B. Check seal and motor shaft.
Leak at shaft seal.
5C. Check and reseat bowl grommet
Leak from bowl spud.
9
TROUBLESHOOTING
Mounting toilet
EXPLODED PARTS
ATLANTES FREEDOM VORTEX VAC PARTS LIST
ItemNo. Part No.
1
1245+
1
AL030+
2
AM002W
2
AM002AW
2
AL002W
2
AL002AW
3
M23A
4
1108A
5
161123
6
31-102
7
221110
8
221105
9
161115
10
221115
11
31-114
12
221012
12
221024
13
221125
14
AM221120
15
221126
16
F035
17
CH57
19
AM021
20
221127
21
221140
22
221135
23
221145
24
221146
25
221160
26
221165
27
F089
28
AM028
29
1236AW
REMOTE INTAKE PUMP
Description
Seat & Cover
Seat & Cover (Elongated)
Atlantes Bowl (White)
Atlantes Bowl (Bone)
Atlantes Bowl Elongated (White)
Atlantes Bowl Elongated (Ivory)
#10 Lockwasher SS
10-32 SS Nut
Macerator Blade
Motor Shaft Seal
Discharge Pump Seal Plate
O-Ring
Impeller
Discharge Pump Macerator Housing
Lock Nut 10-32 W/Nylon(3)
Discharge Motor 12 V
Discharge Motor 24V
Bowl Throat Adapter Clamp - Pump
Bowl Throat Adapter
Bowl Throat Adapter Clamp - Bowl
Isolation Nut (2)
Rubber slinger
Pump Mounting Bracket
Discharge Motor Mounting Clamp
Discharge Hose
Joker Valve (2)
Discharge Adapter Fitting
Joker Valve Insert
Discharge Hose Clamp (small)
Discharge Hose Clamp (large)
Screw: 1/4-20x 2" (2)
Bushing(2)
Spud Assembly
221362
221353
221354
221365
Inlet Adapter Washer
Screw: M4 x 10mm SS Pan Hd
Phillips
65
PLA29
Elbow: 3/4 FPT x 1/2 Barbed
66
SF50W
SEA FRESH: CHECK VLV HG
BOWL MOUNTED FLUSH HANDLE
221361
F201
70
AM665W
Handle SS W/Set Screw
71
AV600
Flush Control & Wire Harness
72
ETB3
Terminal Block 3 Poles
73
F108
Screw #4 x 7/8" (2)
74
HLWQB
1/4"Split Lock Washer (4)
75
M31
1/4" Brass Flat Washer (8)
76
31-722
Nylon Shoulder Washer (2)
77
F069
1/4" Fiber Washer (2)
78
HSB1
1/4-20 Brass Screw (2)
79
M30
1/4-20 Brass Nut (4)
SMART TOILET CONTROL UNITS
80
STC548
Smart Toilet Control (12 & 24VDC)
81
STC545
Control Cable 7 ft
82
221524
Wall Switch Cover Plate - White
82
221524A
Wall Switch Cover Plate - Ivory
83
STC543
Touch Panel W/Back Plate
84
221525
Touch Panel Gasket
MULTIFUNCTION MOMENTARY CONTROL(NOT SHOWN)
221553
W183C
SF77
SF74
SF71
Manual (Relay) Control
Cable for multifunction control
Switch, Vimar
Bazel , Vimar white
Frame, Vimar
SOLENOID VALVE PRESSURIZED SEAWATER UNITS
93
93
93
94
95
30
1660*
Pump Motor *
31
F172
Plastite Screw #10 x 1/2" (4)
32
162325A
Bearing Plate
33
162305
Lower Housing
34
162320
Piston Seat (4)
35
162310
Diaphragm
36
162315
Piston (4)
37
F005
1/4-20 x 5/16" SS Hex SOC
38
162225
O-Ring
39
162420
Fitting Clip (3)
40
162135
Cone Seal (4)
41
162410
3/4" Hose Barb Straight
42
162425
O-Ring (3)
43
162415
Plug Fittting
44
162405
3/4" Hose Barb 90o Fitting
45
F162VT
Inlet Pump Mounting Bolt (4)
46
F144
#10 Washer SS Flat (2)
47
162300W
Lower Housing Assembly
48
162100W
Upper Housing Assembly
49
162200W
Middle Housing Assembly
50
1236E
Bowl Elbow
51
AM012
Nipple
52
AM011
Elbow
PRESSURIZED FRESH WATER UNITS
60
61
51
62
63
64
CWPS12B
CWPS24B
CWPS32B
CWPSMB
PLA14
1/2 GC Solenoid valve 12V
1/2 GC Solenoid valve 24V
1/2 GC Solenoid valve 32V
Mounting Bracket for CWPS
1/2" MPT to 3/4" Barbed Nipple (2)
PARTS NOT SHOWN
RTME12D
Power Converter for 120/240VAC UNIT
ADS
Deodorant System (Seawater Models)
221170 Discharge Hose Strap
221335 Hose, 1/2 inch
221340 Hose Clamps, 1/2 inch
F071
Nylon Shoulder Washer (2)
VCAP+ Vinyl Cap (2)
ADDITIONAL ACCESSORIES AVAILABLE FROM RARITAN
1PCP22 C.P. Cleans Potties, 22 OZ
1PCHGAL Cleans Hoses, Tanks and MSD (gal.)
SFH
Sanitation Hose 1 1/2" (sold by foot)
163000 Seawater Inline Strainer
TD90323 Vented Loop 38mm White
TD90319 Vented Loop 19mm White
TD90314W Aquavalve White with (3) TD90294 Tails
+ specify color
* specify Voltage (12, 24 or 32 volt)
Y Fitting
Solenoid Valve 12VDC D90
Solenoid Valve 24VDC D90
Inlet Adapter Assembly 90 Degrees
(Includes Item 63)
10
81
94
82
95
84
83
80
1
2
21
70
26
65
24
25
22
71
23
7
12
8
5
20
9
10
3
4
13
27
15
14
28
30
37
11
6
60
61
74
63
64
47
43
31
32
75
54
62
48
41
79
49
35
77
19
72
73
75
16
76
38
39
17
46
45
3
78
42
40
33
34
36
44
Atlantes Freedom Vortex Vac Exploded Parts View
11
EXPLODED PARTS
93
LIMITED WARRANTY
1.
2.
3.
4.
5.
6.
Raritan Engineering Company warrants to the original purchaser that this product is free of defects
in materials or workmanship for a period of one year from the product’s date of purchase. Should
this product prove defective by reason of improper workmanship and/or materials within the
warranty period, Raritan shall, at its sole option, repair or replace the product.
TO OBTAIN WARRANTY SERVICE, Consumer must deliver the product prepaid, together with
a detailed description of the problem, to Raritan at 530 Orange St., Millville, N.J. 08332, or 3101 SW
2nd Ave. Ft. Lauderdale, FL 33315. When requesting warranty service, purchaser must present a
sales slip or other document which establishes proof of purchase. THE RETURN OF THE OWNER
REGISTRATION CARD IS NOT A CONDITION PRECEDENT OF WARRANTY COVERAGE.
However, please complete and return the owner Registration Card so that Raritan can contact you
should a question of safety arise which could affect you.
THIS WARRANTY DOES NOT COVER defects caused by modifications, alterations, repairs or
service of this product by anyone other than Raritan; defects in materials or workmanship supplied
by others in the process of installation of this product; defects caused by installation of this product
other than in accordance with the manufacturer’s recommended installation instructions or standard
industry procedures; physical abuse to, or misuse of, this product. This warranty also does not cover
damages to equipment caused by fire, flood, external water, excessive corrosion or Act of God.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY FOR BREACH
OF CONTRACT WHICH BUT FOR THIS PROVISION MIGHT ARISE BY IMPLICATION OR
OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. ALL IMPLIED
WARRANTIES SUCH AS THOSE OF MERCHANTABILITY AND OF FITNESS FOR A
PARTICULAR PURPOSE, IF APPLICABLE, AS WELL AS ANY IMPLIED WARRANTIES
WHICH MIGHT ARISE BY IMPLICATION OF LAW, ARE EXPRESSLY LIMITED TO A
TERM OF ONE YEAR. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG A
LIMITED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
UNDER NO CIRCUMSTANCES SHALL RARITAN BE LIABLE TO PURCHASER OR ANY
OTHER PERSONS FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER
ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU.
No other person or entity is authorized to make any express warranty, promise or affirmation of fact
or to assume any other liability on behalf of Raritan in connection with its products except as
specifically set forth in this warranty.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
530 Orange Street, Millville, NJ 08332 USA
Telephone: 856-825-4900 FAX: 856-825-4409
www.raritaneng.com
Southern Office and Plant:
3101 SW Second Avenue, Fort Lauderdale, FL 33315 USA
Telephone: 954-525-0378 FAX: 954-764-4370
L476 0112vkm
Specifications Subject to Change Without Notice
12
Printed in U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising