Electro-Voice PA4150L datasheet
PA4150L
Four-Channel
Power Amplifier
Key Features:
•
4 x 160W at 4 Ohms
•
2 U Rack Space Chassis
•
Rear Level Controls
•
Bridge Mode Operation Provides
2 x 315W at 8 Ohms
•
Complete Protection Package
•
Selectable 50Hz or 300Hz Hi-Pass Filter for
each Channel
•
Phoenix Type Inputs
Technical Specifications:
Number of Channels
4
Load Impedance
8 Ohm
4 Ohm
•
Phoenix Type Outputs
160W
High Efficiency Circuit Design
Rated Output Power (*Rated Load)
THD<1%, 1kHz
100W
•
•
Front Panel Power On/Off
Rated Output Power (*Rated Load)
THD<0.2%, 20Hz…20kHz
75W
150W
Slew Rate at 1kHz
Frequency Response, -1dB, Ref. 1kHz
General Description:
The Electro-Voice® PA4150 is from the PA series of
professional commercial audio amplifiers. The direct path
airflow design reduces the heat buildup significantly and
allows for 4 full amplifier channels in a slim two rack space
chassis. The audio performance of the PA4150 is superior
and fulfills the requirements in many demanding long term
applications from sound reinforcement, paging or life safety
installations.
The PA4150 features many of the same comprehensive
protection circuits typical in EV amplifiers. Complete
protection is provided for high temperature, audio limiters,
power up delay and peak current limiters. In addition to the
rated output power, the PA4150 provides excellent headroom
for a wide dynamic range on music signals. A selectable
50Hz or 300Hz hi-Pass filter makes it easy to incorporate
the unit into The onboard dynamic limiter ensures that the
output clipping of the PA4150 will not will not generate
excessive distortion. The amplifier channels can be bridged
for more power flexibility.
Marked level controls on the rear panel provide hidden
reliable level adjustments for each channel. Front panel
LEDs indicate signal present, 0 dB, and limit. Phoenix type
connectors for inputs and outputs provide an easy rack wiring.
16V/µs
<10Hz - 40kHz
Damping factor, at 100Hz / 1kHz,
4 Ohm
>250
Power Bandwidth THD=1%, Ref.
1kHz, Half Power
>10Hz - >50kHz
Input Impedance, 20Hz ... 20kHz,
Balanced
>20kOhm
Signal-to-Noise Ratio, A-Weighted
Input Sensitivity at Rated Output
Power or Voltage, 1kHz
100 dB
0dBu (775mV)
THD at rated output power,
MBW=80kHz, 1kHz
<0.1%
IMD-SMPTE, 60Hz, 7kHz
<0.1%
DIM30, 3.15kHz, 15kHz
Crosstalk, Ref. 1kHz, at 10% Rated
Output Power
<0.1%
<-75 dB
Power Requirements
120V or 230V, 50Hz 60Hz
Protection
Audio Limiters
High Temperature
Peak Current Limiters
Turn-On Delay
Cooling
Front-to-Rear
Dimensions (W x H x D), mm 483 x 88 x 406mm (2Ru)
19" x 3.5" x 16"
Weight
18kg (39.65lbs)
Low Impedance Outputs:
- Min. Rated Load for Single Channel Operation is 4 Ohms. 2 Ohm Load is Not Recommended.
- Min. Rated Load for Bridged Operation is 8 Ohms. 4 Ohm Load is Not Recommended.
Block Diagrams:
Dimension Drawings:
Top View
All Dimensions
in Millimeters
PA4150L Part Number:
Front View
PA4150L, 120V -- D170409
Rear View:
12000 Portland Avenue South, Burnsville, MN 55337
Phone:952/884-4051, Fax:952/884-0043
www.electrovoice.com
© Telex Communications, Inc. 1/2006
Part Number LIT-0000XX Rev 1
U.S.A. and Canada only. For customer orders, contact Customer Service at:
800/392-3497 Fax: 800/955-6831
Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:
+ 49 9421-706 0 Fax: + 49 9421-706 265
Other International locations. For customer orders, contact Customer Service at:
+ 1 952 884-4051 Fax: + 1 952 736-4212
For warranty repair or service information, contact the Service Repair department at:
800/685-2606
For technical assistance, contact Technical Support at: 866/78AUDIO
Specifications subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement