Cateye | CC-RD310W | Instruction manual | Cateye CC-RD310W Instruction manual

Cateye CC-RD310W Instruction manual
STRADA SLIM
CC-RD310W
ENG
1
Warning / Caution
CATEYE
STRADA SLIM
•Do not concentrate on the computer while riding. Ride safely!
•Install the magnet, sensor, and bracket securely. Check these periodically.
•If a child swallows a battery, consult a doctor immediately.
•Do not leave the computer in direct sunlight for a long period of time.
•Do not disassemble the computer.
•Do not drop the computer to avoid malfunction or damage.
•When you press the MODE button with the computer installed to the bracket, press around the
dot section on the surface of the computer. Pressing strongly the other section may result in
malfunction or damage.
•When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol.
•Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to local regulations.
•LCD screen may be distorted when viewed through polarized sunglass lenses.
Wireless Sensor
CYCLOCOMPUTER
CC-RD310W
This model comes with a sensor inspired by modern road bikes.
It may not be used for bikes with a large space between the front fork and
spoke.
Before using the computer, please thoroughly read this manual and keep
it for future reference.
Please visit our website, where detailed instructions with movies are
available and the instruction manual can be downloaded.
The sensor was designed to receive signals within a maximum range of 60 cm, to reduce
chance of interference.
When adjusting the wireless sensor, note the following:
•Signals cannot be received if the distance between the sensor and the computer is too large.
•The receiving distance may be shortened due to low temperature and exhausted batteries.
•Signals can be received only when the back of the computer is facing the sensor.
Interference may occur, resulting in incorrect data, if the computer is:
•Near a TV, PC, radio, motor, or in a car or train.
•Close to a railroad crossing, railway tracks, TV stations and/or radar base.
•Using with other wireless devices, or some particular battery lights.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:(1)This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device
that are not expressly approved by CatEye Co., Ltd. May void the user ’s authority to operate
the equipment.
Hereby, CATEYE Co., Ltd., declares that this CC-RD310W is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Preparing the computer
STRADA SLIM
CC-RD310W
ENG
2
Battery case cover
MENU
AC
Perform the All Clear operation, when you use the unit for the first
time or restore the unit to the condition checked at the factory.
1 Clear all data (initialization)
Press the AC button on the
back of the computer.
2 Select the speed units
MODE
3 Enter the tire circumference
Select “km/h” or “mph”.
AC
Dot section
Enter the front wheel tire circumference
of your bicycle in mm.
* Refer to the “Tire circumference reference table” as a guide.
km/h ↔ mph
4 Set the clock
Pressing and holding the MODE button
switches the display to “Displayed time”,
“Hour”, and “Minute” in order.
12h ↔ 24h or increases
the value
Increase the value
MODE
MODE
MODE
Move digits
(Press & hold)
Register the setting
MENU
MODE
MODE
Register the setting
MENU
Tire circumference
There are the following ways to determine the
tire circumference.
•Measure the tire circumference (L)
Measure the distance when the tire turns right
round with your weight applied, while adjusting
the tire pressure appropriately.
L mm
Display format
MENU
Display format Switching “Hour” and “Minute”
(Press & hold)
Register the setting
(Finish)
Hour Minute
•Refer to the tire circumference reference table
* Generally, the tire size or ETRTO is indicated on the side of the tire.
ETRTO
47-203
54-203
40-254
47-254
40-305
47-305
54-305
28-349
37-349
32-369
40-355
47-355
32-406
35-406
40-406
47-406
Tire size
L (mm)
12x1.75
935
12x1.95
940
14x1.50
1020
14x1.75
1055
16x1.50
1185
16x1.75
1195
16x2.00
1245
16x1-1/8
1290
16x1-3/8
1300
17x1-1/4(369) 1340
18x1.50
1340
18x1.75
1350
20x1.25
1450
20x1.35
1460
20x1.50
1490
20x1.75
1515
ETRTO
50-406
28-451
37-451
37-501
40-501
47-507
50-507
54-507
25-520
28-540
32-540
25-559
32-559
37-559
40-559
Tire size
L (mm)
20x1.95
1565
20x1-1/8
1545
20x1-3/8
1615
22x1-3/8
1770
22x1-1/2
1785
24x1.75
1890
24x2.00
1925
24x2.125
1965
24x1(520)
1753
24x3/4 Tubular 1785
24x1-1/8
1795
24x1-1/4
1905
26x1(559)
1913
26x1.25
1950
26x1.40
2005
26x1.50
2010
ETRTO
47-559
50-559
54-559
57-559
58-559
75-559
28-590
37-590
37-584
20-571
23-571
25-571
40-590
Tire size
L (mm)
26x1.75
2023
26x1.95
2050
26x2.10
2068
26x2.125
2070
26x2.35
2083
26x3.00
2170
26x1-1/8
1970
26x1-3/8
2068
26x1-1/2
2100
650C Tubular
1920
26x7/8
650x20C
1938
650x23C
1944
650x25C
1952
26x1(571)
650x38A
2125
ETRTO
40-584
25-630
28-630
32-630
37-630
40-584
50-584
54-584
57-584
18-622
19-622
20-622
23-622
25-622
28-622
30-622
Tire size
650x38B
27x1(630)
27x1-1/8
27x1-1/4
27x1-3/8
27.5x1.50
27.5x1.95
27.5x2.1
27.5x2.25
700x18C
700x19C
700x20C
700x23C
700x25C
700x28C
700x30C
L (mm)
2105
2145
2155
2161
2169
2079
2090
2148
2182
2070
2080
2086
2096
2105
2136
2146
ETRTO
Tire size
L (mm)
32-622 700x32C
2155
700C Tubular
2130
35-622 700x35C
2168
38-622 700x38C
2180
40-622 700x40C
2200
42-622 700x42C
2224
44-622 700x44C
2235
45-622 700x45C
2242
47-622 700x47C
2268
54-622 29x2.1
2288
56-622 29x2.2
2298
60-622 29x2.3
2326
How to install the unit on your bicycle
STRADA SLIM
Refer to the Quick Start Manual, where you can learn how to
install the unit in detail using a movie.
http://www.cateye.com/products/detail/CC-RD310W/manual/
CC-RD310W
ENG
(SPD-02)
Bracket
Bracket rubber pad
Speed sensor
or
Sensor
rubber pad
(x 3)
1-2
1-1
Rubber band
(large band for bracket)
(middle and small bands for sensor)
Nylon tie
Magnet
Attach the bracket to the stem or handlebar
1-1 When mounting the bracket to the stem
Bracket
2
3
Bracket
rubber pad
Nylon tie
Rubber band
* Use a nylon tie together to fix it firmly.
1-2 When mounting the bracket to the handlebar
Bracket
Rubber band
Nylon tie
or
Bracket
rubber pad
2
1
3
How to install the unit on your bicycle
STRADA SLIM
CC-RD310W
ENG
Install the sensor and magnet in a position where
the following conditions are satisfied.
The distance from the computer
to the sensor is within the transmission data length, and the back
of the computer faces downward.
The magnet passes through the sensor
zone of the speed sensor.
2 Install the sensor
Speed sensor
(SPD-02)
Nylon tie
or
Magnet
Speed sensor
(SPD-02)
SENSOR ZONE
The clearance between the sensor surface and the magnet is within 5 mm.
Max.
60 cm
Speed sensor
(SPD-02)
(23-5/8” )
Sensor rubber pad
Rubber band
Inside the
front fork
3 Install the magnet
4 Remove/Install the computer
Click
5 mm
While supporting it by hand,
Magnet
(3/16” )
Check the mounting position of the sensor and magnet
To the SENSOR ZONE
Spoke
Spoke
Push it out as if lifting the front up
Get an estimate of the mounting position where the clearance
between the magnet surface and
sensor zone is 5 mm or less, by
sliding up and down the sensor
and magnet before mounting.
Inside the front fork
Positioning and testing
Adjust the sensor magnet so that the conditions of
,
,
then check the operation by turning the front wheel slowly.
are satisfied, and
4
Operating the computer [Measuring screen]
STRADA SLIM
CC-RD310W
ENG
5
Switching computer function
Pressing the MODE button switches the selected data at the bottom in the order shown in the
following figure.
Pace arrow
Indicates whether the current speed is faster ( ) or
slower ( ) than the average
speed.
Sensor signal icon
Flashes in synch with a sensor signal.
Tire icon
Current speed
0.0 (4.0) – 105.9 km/h
[0.0 (3.0) – 65.9 mph]
MODE
Tm Elapsed Time
MODE
Dst Trip Distance
0:00’00” – 9:59’59”
Dst2
0.00 – 999.99 km [mile]
Trip Distance-2
Speed unit
0.00 – 999.99 /
1000.0 - 9999.9 km [mile]
MODE
Selected mode
MODE
Clock
0:00 - 23:59 or
1:00 - 12:59
MODE operation when the computer
is mounted on the bracket
MODE
MODE
Odo Total Distance
MODE
When the computer is mounted on the bracket,
once you press the dot section on the unit, the
MODE button is pressed.
0.0 – 9999.9 /
10000 - 99999 km[mile]
MENU
MODE
Mx Maximum Speed
0.0(4.0) – 105.9 km/h
[0.0(3.0) – 65.0 mph]
Pressing MENU on the measurement screen
changes to the menu screen. Various settings can be changed on the menu screen.
Av Average Speed
0.0 – 105.9 km/h
[0.0 – 65.0 mph]
* The average speed displays .E instead of the measurement value,
when Tm exceeds about 27 hours
or Dst exceeds 999.99 km. Reset
the data.
To “Changing the computer settings [Menu screen]” (page 7)
Operating the computer [Measuring screen]
Starting / Stopping measurement
The unit automatically measures according to the movement
of your bicycle.
The speed unit (km/h or mph) flashes during measurement.
Starting
measurement
Stopping
measurement
STRADA SLIM
Resetting data
With the data other than Dst2 displayed, pressing and holding
the MODE button returns the measurement data to 0.
With Dst2 displayed, pressing and holding the MODE button
returns only Dst2 to 0.
The total distance (Odo) cannot be reset.
CC-RD310W
ENG
6
Power-saving function
If the computer has not received a signal for 10 minutes,
power-saving screen will activate and only the clock will be
displayed.
When you press MODE, or the computer receives a sensor
signal, the measuring screen reappears.
10 minutes
Power-saving screen
MODE
(Press & hold)
1 hour
Sleep
MODE
If another 60 minutes of inactivity elapses in the powersaving screen, only the speed unit is displayed on the screen.
With such a screen, pressing the MODE button returns to the
measurement screen.
Changing the computer settings [Menu screen]
STRADA SLIM
With a menu you want to
change displayed, once
you press and hold the
MODE button, you can
change various setting by
MODE
(Press & hold) the button operation as
described.
Changing the
settings
MENU
Measuring
screen
Pressing MENU on the measurement screen changes to the menu
screen.
Various settings can be changed
on the menu screen.
* After changing, be sure to
register the setting(s) by
Register the pressing the MENU butsetting
ton.
* Leaving the menu screen
without any operation for
1 minutes returns to the
MENU
measurement screen, and
changes are not saved.
MENU
CC-RD310W
Overview of the menu screen
MODE
MODE
Setting the tire
circumference
Switching the
circumference A/B
Setting the
clock
MODE
MODE
MODE
Selecting the
measurement unit
MODE
Entering the total
distance
Setting the
function
From “Selecting the measurement unit”
To “Setting the clock”
Switching the circumference A/B
The tire to be used (
Setting the tire circumference
) can be selected.
MODE
Changing the
settings
Set the tire circumference.
MODE
Changing the
settings
↔
MODE
(Press & hold)
ENG
MODE
Switch
MODE
(Press & hold)
Move digits
Increase
the value
MODE
Register the
setting
Register the
setting
MENU
MENU
(Press & hold)
MODE
7
Changing the computer settings [Menu screen]
STRADA SLIM
From “Setting the tire circumference”
Setting the function
Set the clock.
MODE
Selecting the display
12h ↔ 24h
MODE
(Press & hold)
ENG
To “Entering the total distance”
Setting the clock
Changing the
settings
CC-RD310W
You can skip the selected data to be displayed.
Once you select “Off” for a particular selected
data, it will be skipped in the measurement screen.
Changing the
settings
MODE
MODE
Dst
Dst 2
Selected
data switch
Av
MODE
(Press & hold)
Mx
MODE
(Press & hold)
Odo
MODE
(Press & hold)
Hour
Increase
the value
Register the
setting
MODE
ON ↔ OFF
MENU
MODE
(Press & hold)
Register the
setting
MENU
Minute
Increase
the value
MODE
MODE
(Press & hold)
MODE
* The elapsed time (Tm) cannot be skipped.
* Even the hidden selected mode is measured,
and the measurement result will be reflected
when it is displayed again.
8
Changing the computer settings [Menu screen]
STRADA SLIM
From “Setting the function”
CC-RD310W
ENG
To “Switching the circumference A/B”
Entering the total distance
Selecting the measurement unit
Enter the total distance.
MODE
(No decimal number can be entered.)
* Once you enter any value to the total distance, you can start from
the value you entered. Use this function when you renew your unit
and/or replace the battery.
The speed unit (km/h or mph) can be selected.
Changing the
settings
Changing the
settings
km/h ↔ mph
MODE
(Press & hold)
MODE
(Press & hold)
Move digits
MODE
Register the
setting
(Press & hold)
MENU
Register the
setting
Increase
the value
MENU
MODE
MODE
MODE
9
In use
STRADA SLIM
Maintenance
To clean the computer or accessories, use diluted neutral
detergent on a soft cloth, and wipe it off with a dry cloth.
Replacing the battery
Computer
When the display becomes dim, replace the battery. Install a
new lithium battery (CR1616) with the (+) side faced upward.
Troubleshooting
Press
10
The sensor signal icon does not flash.
(the speed is not displayed)
Check that the clearance between the sensor and magnet
is not too large. (Clearance: within 5 mm)
Check that the magnet passes through the sensor zone
correctly.
1603891
1603890
Speed sensor
(SPD-02)
Parts kit
Is the computer installed at the correct angle?
Back of computer must face toward the sensor.
Slide
CR1616
OK
* Press the top edge of waterproof
NO!
inner cap to remove it.
* After replacing the computer battery, follow the procedure described
in “Preparing the computer”
* Noting the total distance before replacing the battery allows
you to start from the total distance you enter manually after
replacing it.
Check that the distance between the computer and sensor is correct. (Distance: within 20 to 60 cm)
Install the sensor within the specified range.
Is the computer or sensor battery weak ?
* In winter, battery performance diminishes.
If the computer reacts only when it is close to the sensor,
weak batteries may cause it.
Replace with new batteries according to the procedure
specified in the section “Replacing the battery”.
Nothing is displayed by pressing the button.
Replace the computer battery according to the procedure specified in the section “Replacing the battery”.
Incorrect data appear.
Speed sensor
When the speed is not displayed even after adjusting
correctly, replace the battery.
Insert new lithium batteries
(CR2032) with the (+) sign
upward, and close the battery
cover firmly.
* After replacement, check the
positions of the sensor and
magnet.
ENG
Standard accessories
Adjust the positions of the magnet and sensor.
Waterproof inner cap
CC-RD310W
Open
Close
COIN
1603893
1603892
Rubber band / nylon tie
1699691N
Wheel magnet
Bracket kit
1603850
Lithium battery
CR1616
1665150
Lithium battery
CR2032
Optional accessories
Clear all according to the procedure described in “Preparing the computer”.
All measured data are deleted.
1602196
1604100
Speed sensor
(SPD-01)
Out-front bracket
CR2032
1602194
Bracket kit
(FlexTight™)
1600280N
Bracket band
(FlexTight™)
1602193
Bracket
(for FlexTight™)
In use
STRADA SLIM
Specification
Battery
Battery life
Limited warranty
Lithium battery (CR1616) x 1
Approx. 1 year
Computer (If the computer is used for 1 hour/
day; the battery life will vary depending on the conditions of use.)
Speed
sensor
Lithium battery (CR2032) x 1
Distance reaches about
10000 km (6250 mile)
*This is the average figure of being used under 20 °C temperature and the distance between the computer and the
sensor is 60 cm.
*The factory-loaded battery life might be shorter than the
above-mentioned specification.
Controller
4 bit, 1-chip microcomputer
(Crystal controlled oscillator)
Display
Liquid crystal display
Sensor
No contact magnetic sensor
Transmission
Between 20 and 60 cm
distance
Tire circum- 0100 mm - 3999 mm
ference range (Initial value: A = 2096 mm, B = 2096 mm)
0 °F - 104 °F (0 °C - 40 °C)
(This product will not display appropriately
Working tem- when exceeding the Working Temperature
perature
range. Slow response or black LCD at lower
or higher temperature may happen respectively.)
1-55/64” x 1-17/64” x 1/2”
Computer (47 x 32 x 12.5 mm) /
0.43 oz (12 g)
Dimensions/
weight
2-43/64” x 1-3/16” x 21/64”
Speed
(67.7 x 30 x 8.1 mm) /
sensor
0.48 oz (13.5 g)
*The specifications and design are subject to change without
notice.
2-Years Computer/Sensor only
(Accessories and Battery Consumption excluded)
CatEye cycle computers are warranted to be free of defects
from materials and workmanship for a period of two years
from original purchase. If the product fails to work due to
normal use, CatEye will repair or replace the defect at no
charge. Service must be performed by CatEye or an authorized retailer. To return the product, pack it carefully and
enclose the warranty certificate (proof of purchase) with
instruction for repair. Please write or type your name and
address clearly on the warranty certificate. Insurance, handling and transportation charges to CatEye shall be borne by
person desiring service. For UK and REPUBLIC OF IRELAND
consumers, please return to the place of purchase. This does
not affect your statutory rights.
Please register your CatEye product on the website.
http://www.cateye.com/en/support/regist/
CO.,LTD.
2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan
Attn: CATEYE Customer Service Section
Phone : (06)6719-6863
Fax
: (06)6719-6033
E-mail : support@cateye.co.jp
URL
: http://www.cateye.com
[For US Customers]
CATEYE AMERICA, INC.
2825 Wilderness Place Suite 1200, Boulder CO 80301-5494 USA
Phone : 303.443.4595
Toll Free : 800.5.CATEYE
Fax
: 303.473.0006
E-mail : service@cateye.com
CC-RD310W
ENG
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising