INSTALLATION
RED TAILLIGHT LENS
5452
PARTS INCLUDED
1
1
1
1
1
1
Red Laydown Taillight Lens with Clear License Plate Window
Reflector
Clear 1157 Bulb
Bulb Socket with Connector
Gasket
Installation Instructions
Please read and understand entire instructions before starting installation.
THANK YOU FOR CHOOSING KϋRYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR
PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL
INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES REGARDING
THE USE AND CARE OF THIS PRODUCT.
WARNING!
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING
THE CONTENTS DESCRIBED HEREIN CAN RESULT IN
POTENTIAL DEATH OR SERIOUS INJURY.
ATTENTION! This indication alerts you to the fact that ignoring the contents
described herein may negatively affect product performance and
functionality.
TOOLS SUGGESTED
Phillips Head Screwdriver
STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE
PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.
STEP 1
Read and understand all steps in the instructions before starting the
installation. Park the motorcycle on a hard, level surface and turn off the
ignition.
NOTE: Installation is shown on a 2005 Heritage Softail®; while
representative of typical procedure, there may be minor differences
when installed on other Models.
STEP 2
Remove the two stock Phillips head screws securing the taillight lens to the
base. PIC 1 Set the screws aside, they will be re-used.
STEP 3
Unplug the stock taillight bulb connector from the base. PIC 2 Push up
on the tab on the underside of the connector and pull it out of the socket; set
the stock taillight bulb connector aside, it will not be re-used.
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products
sold hereunder, shall be free of defects in
materials and workmanship for a period of one
(1) year from the date of purchase by the
consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt
showing the date the customer purchased the
product(s).
●The product must be properly installed,
maintained and operated under
normal conditions.
●Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated
products.
●Küryakyn shall not be liable for any
consequential and incidental damages, including
labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in
delivery, delivery in nonconforming condition, or
for any breech of contract or duty between
Küryakyn and a customer.
●Küryakyn products are often intended for use in
specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
●Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the
consumer. L.E.D.’S contained in components of
Küryakyn products will be warranted for defects
in materials and workmanship for 3 years from
the date of purchase where as all other
components shall be warranted for one(1) year.
This includes, but is not limited to; control
modules, wiring, chrome & other components.
●Küryakyn makes no warranty of any kind in
regard to other manufacturer¹s products
distributed by Küryakyn. Küryakyn will pass on
all warranties made by the manufacturer and
where possible, will expedite the claim on behalf
of the customer, but ultimately, responsibility for
disposition of the warranty claim lies
with the manufacturer.
ABOUT OUR CATALOG
For purchasing Küryakyn® products, you
can receive a complete catalog free of charge.
Send the Proof-of-Purchase below with
your address to: Küryakyn, P.O. Box 339,
Somerset, WI 54025.
Please indicate either Accessories Catalog for
Harley-Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and
accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights reserved.
-cont.5452-22HD-0711
PIC 1
STEP 4
Remove the adhesive backing from the included gasket; position the
gasket as shown in PIC 3 and press into place.
STEP 5
Plug the included bulb socket connector into the socket in the base. See
PIC 4
STEP 6
Push in and twist the included bulb clockwise into the new bulb socket.
The included bulb only fits in the socket one way.
STEP 7
Position the bulb socket in the back of the included reflector; push the
socket into the reflector. PIC 5
STEP 8
Tuck the socket wires into the recess in the taillight base.
STEP 9
Place the included taillight lens over the reflector and secure it with the
two screws removed in STEP 2.
STEP 10
Ensure that the taillight and brake light operate properly before operating
the motorcycle.
PIC 2
UNPLUG HERE
PIC 3
WARNING!
ENSURE PROPER TAILLIGHT OPERATION BEFORE RIDING
THE MOTORCYCLE. VISIBILITY IS A MAJOR CONCERN FOR
MOTORCYCLISTS. TAILLIGHT MALFUNCTION COULD
RESULT IN DEATH OR SERIOUS INJURY.
ATTENTION! It is the installer’s responsibility to ensure that all of the fasteners
(including pre-assembled) are tightened before operation of the
motorcycle. Küryakyn will not issue a warranty on components
lost due to improper installation. Periodic maintenance may be
required.
PIC 5
PIC 4
BULB SOCKET REMOVED FROM BIKE FOR CLARITY
NOTE THE LOCATING ANGLES
PAGE
2
Ride On!
RED TAILLIGHT LENS
INSTALLATION
">