Radio Shack 900 MHz Digital Spread Spectrum Dual Keypad Cordless Telephone with Caller ID/Call Waiting ID Owner`s manual

Radio Shack 900 MHz Digital Spread Spectrum Dual Keypad Cordless Telephone with Caller ID/Call Waiting ID Owner`s manual
900 MHz Digital Spread
Spectrum Dual-Keypad
Cordless Speakerphone
Please read before using this equipment.
Owner’s Manual
with Caller ID/Call Waiting Deluxe
ˆ Important Information
This phone has been tested and found to
comply with all applicable UL and FCC standards.
WARNING: To reduce the risk of fire or
shock hazard, do not expose this product to rain
or moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
!
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
This symbol is intended to alert
you to the presence of uninsulated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to constitute a risk of electric shock. Do
not open the product’s case.
!
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accompanying this product.
IMPORTANT CALLER ID
INFORMATION
• caller's number only
• caller's name only
• caller's name and number.
READ THIS BEFORE
INSTALLATION
We have designed your phone to conform to
federal regulations, and you can connect it to
most telephone lines. However, each phone
(and each device, such as a telephone or answering machine) that you connect to the
telephone line draws power from the telephone line. We refer to this power draw as
the device's ringer equivalence number, or
REN. The REN is on the bottom of your
phone.
If you use more than one phone or other device on the line, add up all of the RENs. If the
total is more than five (or three in rural areas), your telephones might not ring. If ringer
operation is impaired, remove a device from
the line.
Your phone complies with Part 68 of FCC
Rules. You must, upon request, provide the
FCC registration number and the REN to
your telephone company. Both numbers are
on the bottom of your phone.
Note: You must not connect your phone to:
• coin-operated systems
To use the phone's Caller ID and Call Waiting with Caller ID features, you must be in an
area where those services are available and
you must subscribe to those services
through your local phone company. Where
Caller ID is offered, one or more options are
generally available:
• party-line systems
• most electronic key telephone systems
Important:
© 2001 RadioShack Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.
2
Important Information
• Cordless phones such as this one
require AC power to operate. When the
AC power is off, you cannot dial out or
receive incoming calls using your
phone. For this reason, the phone
should not be your only telephone. To be
safe, you should also have a phone that
does not require AC power to operate
(not a cordless phone) so you can still
make and receive calls if there is an AC
power failure.
• Some cordless phones operate at frequencies that might cause interference
to nearby TVs and VCRs. To minimize
or prevent such interference, the base of
the cordless phone should not be placed
near or on top of a TV or VCR.
• Your cordless phone operates on standard radio frequencies, as allocated by
the FCC. Even though your phone's
access protection code prevents unauthorized use of your phone line, it is possible for other radio units operating on
similar frequencies within a certain area
to unintentionally intercept your conversations and/or cause interference. This
possible lack of privacy can occur with
any cordless phone.
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone causes
problems on the phone line, the phone company can temporarily discontinue your service. If this happens, the phone company
attempts to notify you in advance. If advance
notice is not practical, the phone company
notifies you as soon as possible and advises
you of your right to file a complaint with the
FCC.
Also, the phone company can make changes
to its lines, equipment, operations, or procedures that could affect the operation of this
telephone. The telephone company notifies
you of these changes in advance, so you can
take the necessary steps to prevent interruption of your telephone service.
LIGHTNING
Your telephone has built-in protection circuits
to reduce the risk of damage from surges in
telephone line and power line current. These
protection circuits meet or exceed the FCC
requirements. However, lightning striking the
telephone or power lines can damage your
telephone.
Lightning damage is not common. Nevertheless, if you live in an area that has severe
electrical storms, we suggest that you unplug
your phone when storms approach to reduce
the possibility of damage.
FCC STATEMENT
The phone complies with the limits for a
Class B digital device as specified in Part 15
of FCC Rules. These limits provide reasonable protection against radio and TV interference in a residential area. However, your
equipment might cause TV or radio interference even when it is operating properly. To
eliminate interference, you can try one or
more of the following corrective measures:
• Reorient or
antenna.
relocate
the
receiving
• Increase the distance between the
equipment and the radio or TV.
• Use outlets on different electrical circuits
for the equipment and the radio or TV.
Consult your local RadioShack store if the
problem still exists.
IMPORTANT SAFETY
Important Information
3
INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock
and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions
marked on the product.
3. Never install telephone wiring during a
lightning storm.
4. Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
5. Never touch uninsulated telephone
wires or terminals unless the telephone
line has been disconnected at the network interface.
6. Use caution when installing or modifying
telephone lines.
7. Do not fix the AC power supply cord to
building surfaces with metal fittings (If
the product has an AC power cord).
8. Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
9. Do not use this product near water, for
example, near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.
10. Do not place this product on an unstable
cart, stand, or table. The product may
fall, causing serious damage to the
product.
11. Slots and openings in the cabinet and
the back or bottom are provided for ventilation. To protect it from overheating,
these openings must not be blocked or
4
covered. The openings should never be
blocked by placing the product on a bed,
sofa, rug, or other similar surface. This
product should never be placed near or
over a radiator or heat register. This
product should not be placed in a built-in
installation unless proper ventilation is
provided.
12. This product should be operated only
from the type of power source indicated
on the marking label. If you are not sure
of the type of power supply to your
home, consult your local power company.
13. Do not allow anything to rest on the
power cord. Do not locate this product
where the cord will be stepped on.
14. Do not overload wall outlets and extension cords as this can result in a risk of
fire or electric shock.
15. Never push objects of any kind into this
product through cabinet slots as they
may touch dangerous voltage points or
short out parts that could result in a risk
of fire or electric shock. Never spill liquid
of any kind on the product.
16. To reduce the risk of electric shock, do
not disassemble this product. Take it to
a qualified serviceman when service or
repair work is required. Opening or
removing covers may expose you to
dangerous voltage or other risks. Incorrect reassembly can cause electric
shock when the product is subsequently
used.
17. Unplug this product from the wall outlet
and refer servicing to qualified service
personnel under the following conditions:
• When the power cord plug is damaged
or frayed.
Important Information
• If liquid has been spilled into the product.
and may cause damage to the eyes or
skin. It may be toxic if swallowed.
• If the product has been exposed to rain
or water.
4. Exercise care in handling the battery
pack in order not to short it with conducting materials such as rings, bracelets,
and keys. The battery or conductor may
overheat and cause burns.
• If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are covered by the operating instructions
because improper adjustment of other
controls may result in damage and will
often require extensive work by a qualified technician to restore the product to
normal operation.
• If the product has been dropped or the
cabinet has been damaged.
• If the product exhibits a distinct change
in performance.
5. Charge the battery pack provided with or
identified for use with this product only in
accordance with the instructions and
limitations specified in this owner’s manual.
6. Observe proper polarity orientation
between the battery pack and the battery charger.
SAVE THESE
INSTRUCTIONS
18. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric
shock from lightning.
19. Do not use the telephone to report a gas
leak in the vicinity of the leak.
BATTERY SAFETY
INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF
FIRE OR INJURY, READ AND FOLLOW
THESE INSTRUCTIONS.
1. Use only the appropriate type and size
of battery pack specified in the instruction manual provided for this product.
2. Do not dispose of the battery pack in a
fire. The cell may explode. Check with
local codes for possible special disposal
instructions.
3. Do not open or mutilate the battery
pack. Released electrolyte is corrosive
Important Information
5
ˆ Contents
Installation ............................................................................................................................
Mounting the Phone ........................................................................................................
On a Desk Top, Shelf, or Table ................................................................................
On a Wall Plate or Wall ............................................................................................
Connecting, Charging, and Replacing the Battery Pack .................................................
Setting the Dialing Mode .................................................................................................
Setting the Ringer Tone/volume ......................................................................................
Turning Auto Talk On/Off .................................................................................................
Turning Caller ID/Call Waiting On/Off .............................................................................
Storing Your Area Code ..................................................................................................
10
10
10
11
11
12
13
13
13
14
Operation .............................................................................................................................. 15
Making and Receiving Calls Using the Handset ............................................................. 15
Selecting the Channel ..................................................................................................... 15
Adjusting the Handset Volume ........................................................................................ 15
Using the Speakerphone ................................................................................................. 15
Switching Between the Handset and Speakerphone ............................................... 15
Using Both the Handset and Speakerphone ............................................................ 16
Using Mute ...................................................................................................................... 16
Using Redial .................................................................................................................... 16
Using Flash ..................................................................................................................... 16
Using Tone Services On a Pulse Line ............................................................................. 16
Using Page/Intercom ....................................................................................................... 17
Transferring a Call Between the Handset and Base ................................................ 17
Memory Dialing ............................................................................................................... 17
Storing a Number in the Handset’s Memory ............................................................ 18
Editing or Deleting a Number in the Handset’s Memory .......................................... 19
Storing a Number in the Base’s Memory ................................................................. 19
Entering a Pause ..................................................................................................... 19
Reviewing the Handset’s Memory Numbers ............................................................ 19
Dialing a Memory Number ....................................................................................... 20
Chain-Dialing Service Numbers ............................................................................... 20
Testing Stored Emergency Numbers ....................................................................... 20
Using a Headset .............................................................................................................. 20
Caller ID Operation ............................................................................................................... 21
Call Waiting Options Service ........................................................................................... 21
Using Call Waiting Options ...................................................................................... 21
Using Ask to Hold .................................................................................................... 22
Using Conference .................................................................................................... 22
Reviewing Caller ID Records .......................................................................................... 22
Caller ID Messages .................................................................................................. 23
Adding/Deleting the Area Code ....................................................................................... 23
Dialing Numbers from a Caller ID Record ....................................................................... 23
Storing a Caller ID Record to Memory ............................................................................ 23
Deleting Caller ID Records .............................................................................................. 24
6
Contents
Deleting All Caller ID Records ................................................................................. 24
Troubleshooting ................................................................................................................... 25
Care ................................................................................................................................ 26
Contents
7
ˆ Features
Your RadioShack 900 MHz Digital Spread
Spectrum Speakerphone uses the most advanced cordless telephone technology to
give you superior audio quality and extended
range.
The phone’s Caller ID records each caller’s
telephone number (and name, if available in
your area) and the date and time of the call,
as provided by your local phone company to
Caller ID service subscribers.
If you subscribe to Call Waiting with Caller
ID, the phone shows you the incoming caller
information, even when you are already on
the phone.
Your phone has these features:
Caller ID/Call Waiting Deluxe — gives you
several options for handling waiting callers
(you must subscribe to the Call Waiting Options Service through your phone company
to use this feature).
3-Line Liquid Crystal Display — lets you
view an entire Caller ID record on one
screen.
30-Number Memory Dialing — lets you
store up to 30 numbers (20 in the handset
and 10 in the base) in memory for easy dialing.
Two-Way Intercom/Paging System — lets
you send a signal from the base to the handset, or from the handset to the base, to page
someone or locate the handset when it is
away from the base. If someone answers,
you can use the phone as an intercom.
Auto Talk — lets you set the handset so you
can answer a call by simply lifting the handset from the base or by pressing any key
when the handset is away from the base.
Headset Jack — lets you connect an optional headset (available from your local RadioShack store) for hands-free convenience.
900 MHz Operation — provides longer
range and less interference than many other
cordless phones.
Volume Control — lets you adjust the volume you hear through the handset and the
base.
Spread Spectrum Technology — spreads
the signal across several frequencies, providing additional security for your phone conversations.
Adjustable Ringers — you can set different
volumes for the handset and base ringers.
Caller ID Memory — stores up to 50 Caller
ID records.
Dual Keypad — a full set of keys on both the
handset and base let you use either keypad
to operate the phone.
Speakerphone — lets you make or answer
calls without using the handset.
8
Ample Talk and Standby Time — the supplied battery (when fully charged) provides
about 6 hours of talk time or 7 days of standby time.
20 Channels — automatically selects a clear
channel when you make or answer a call.
Security Access-Protection Code — automatically prevents other cordless phone users from using your phone line while the
handset is off the base.
Features
Redial — lets you quickly redial any of the
three last numbers dialed on the handset
and the last number dialed on the base.
Tone/Pulse Dialing — lets you use either
type of service.
Hearing-Aid Compatibility — lets you use
your phone with hearing aids that have a T
(telephone) switch.
Features
9
ˆ Installation
MOUNTING THE PHONE
You can place the phone’s base on a desk or
table, mount it on a standard wall plate, or
mount it directly on a wall. Choose a location
that is:
• near an AC outlet
update the wiring yourself using jacks and
adapters (available at your local RadioShack
store), or have the telephone company update the wiring for you. You must use compatible modular jacks that are compliant with
Part 68 of FCC Rules.
Note: The USOC number of the jack to be
installed is RJ11C (or RJ11W for a wall plate
jack).
• near a modular telephone line jack
• out of the way of normal activities
On a Desk Top, Shelf, or Table
• away from electrical machinery, electrical appliances, metal walls or filing cabinets, wireless intercoms, alarms, and
room monitors
• away from other cordless phones
The base’s location affects the phone’s
range. If you have a choice of several locations, try each to see which provides the best
performance.
1. Insert the bracket’s tabs into the base’s
upper tab slots, then press down on the
bracket’s clips and insert them into the
clip slots.
2. Plug one end of the supplied long modular cord into the TEL LINE jack on the
back of the base and route the cord
through the strain relief hook on the
bracket.
3. Plug the modular cord’s other end into a
modular telephone line jack.
Cautions:
You must use a Class 2 power
source that supplies 9V AC
and delivers at least 350 mA.
Its center tip must be set to positive and
its plug must fit the phone's DC IN 9V
jack. The supplied adapter meets these
specifications. Using an adapter that
does not meet these specifications
could damage the phone or the adapter.
!
• Always connect the AC adapter to the
phone before you connect it to AC
power. When you finish, disconnect the
adapter from AC power before you disconnect it from the phone.
4. Insert the supplied AC adapter’s barrel
plug into the DC IN 9V jack on the back of
the base.
5. Route the adapter’s cord through the
strain relief slot on the bottom of the
base.
6. Plug the adapter into a standard AC outlet.
7. Lift the base’s antenna to a vertical position.
Your telephone connects directly to a modular telephone line jack. If your telephone wiring does not have a modular jack, you can
10
Installation
On a Wall Plate or Wall
1. Insert the bracket’s tabs into the base’s
lower tab slots, then press down on the
bracket’s clips and insert them into the
clip slots.
2. Plug one end of the supplied short modular cord into the TEL LINE jack on the
back of the base.
3. Insert the supplied AC adapter’s barrel
plug into the DC IN 9V jack.
4. Route the adapter cord through the
groove on the bracket.
5. Plug the modular cord’s other end into
the wall plate jack, then align the
bracket’s keyhole slots with the wall
plate studs and slide the phone downward to secure it.
3. Align the bracket’s keyhole slots with the
mounting screws and slide the phone
downward to secure it.
CONNECTING, CHARGING,
AND REPLACING THE
BATTERY PACK
The phone comes with a rechargeable nickel-cadmium (Ni-Cd) battery pack in the handset. Before using your phone, you must
connect the battery pack, then charge it for
about 24 hours.
1. Press down and slide off the battery
pack compartment cover.
2. Lift the battery pack out of the compartment.
6. Plug the adapter into a standard AC outlet.
3. Plug the battery pack's connector into
the socket in the compartment, (the connector fits only one way), replace the
battery pack, and replace the cover.
7. Lift the base’s antenna to a vertical position.
To charge the battery pack, place the handset either faceup or facedown on the base.
Note: To mount the phone directly on a wall,
you need two screws (not supplied) with
heads that fit into the keyhole slots on the
bottom of the base.
The CHARGE/IN USE indicator on the base
lights and JejWb0&& appears.
Follow the steps under “On a Wall Plate or
Wall”, then apply these additional instructions.
Important: Be sure the battery pack is properly connected before you try to charge it.
The CHARGE/IN USE indicator lights when
the handset is on the base even if the battery
pack is not properly connected.
1. Drill two holes 315/16 inches (100 mm)
apart. Then thread a screw into each
hole, letting the heads extend about 1/8
inch (3 mm) from the wall.
Recharge the battery pack when Bemý8Wjj[ho
flashes.
2. Plug one end of the supplied long modular cord into the TEL LINE jack on the
back of the base and route the adapter
cable and modular cords through the
grooves on the bracket.
• When you first use the phone after
charging or recharging the battery pack,
the phone might not work and you might
hear a beep when you press TALK.
Return the handset to the base for about
5 seconds to reset the security accessprotection code.
Notes:
Installation
11
• If the handset or the base loses power,
the security access-protection code
might be lost. To reset the code, return
the handset to the base for about 5 seconds.
• Using a pencil eraser, clean the charging contacts on the handset and base
about once a month.
• If the battery pack becomes weak during
a call, the handset beeps every 3 seconds and Bemý8Wjj[ho flashes. When this
happens, you cannot make a call until
you recharge the battery pack.
• About once a month, fully discharge the
battery by keeping the handset off the
base until Bemý 8Wjj[ho flashes. Otherwise, the battery pack loses its ability to
fully recharge.
• If the display is blank and the phone
does not work, recharge the battery
pack. (The battery power might be too
low to light the display.)
• If you are not going to use your phone
for an extended period of time, disconnect the battery pack. This increases the
battery pack's usable life.
The supplied battery pack should last about
a year. If the battery pack does not hold a
charge for more than 2 hours after an overnight charge, replace it with a new 3.6-volt,
600 mAh battery pack with a connector that
fits the socket in the battery compartment.
You can order a replacement battery pack
through your local RadioShack store. Install
the new battery pack and charge it for about
24 hours.
Warning: Dispose of the old battery pack
promptly and properly. Do not burn or bury it
(see “Battery Safety Instructions” on Page 5
for additional information on proper battery
handling).
12
If you have trouble replacing the battery
pack, take the phone to your local RadioShack store for assistance.
Important: The EPA certified
RBRC® Battery Recycling Seal
on the nickel-cadmium (Ni-Cd)
battery indicates RadioShack
is voluntarily participating in an
industry program to collect and recycle these
batteries at the end of their useful life, when
taken out of service in the United States or
Canada. The RBRC program provides a
convenient alternative to placing used Ni-Cd
batteries into the trash or the municipal
waste stream, which may be illegal in your
area. Please call 1-800-THE-SHACK (1800-843-7422) for information on Ni-Cd battery recycling and disposal bans/restrictions
in your area. RadioShack’s involvement in
this program is part of the company’s commitment to preserving our environment and
conserving our natural resources.
SETTING THE DIALING
MODE
Your phone comes set for tone dialing. If you
have pulse service, you need to change the
dialing mode. If you are not sure which type
of service you have, do this test.
Press SPEAKER and listen for a dial tone.
Press any number other than 0.
Note: If your phone system requires that you
dial an access code (9, for example) before
you dial an outside number, do not press the
access code either.
If the dial tone stops, you have touch-tone
service. If the dial tone continues, you have
pulse service.
To set the dial mode, press SPEAKER to
hang up the phone if necessary. Then, on
the base keypad, hold down FLASH. until the
phone beeps, then press # to set to pulse
Installation
mode or
beeps.
∗ to set to tone mode. The phone
Note: The phone exits setting mode if a call
is received, or if you press SPEAKER.
SETTING THE RINGER
TONE/VOLUME
You can select one of four different ringer
tone/volume settings on the handset. At any
time, except during a call, repeatedly press
VOL/CID 8 or 9 to select the desired ringer
setting. Each time you press a button, the
phone rings at the selected setting and H_d][h
7 >_]^, H_d][h 7 Bem, H_d][h 8 >_]^, or H_d][h 8
Bem appears.
You can also turn off the ringer. At any time,
except during a call, press and hold VOL/CID
9 until the phone beeps and H_d][hýE\\ appears. When you place the handset faceup
on the base, 2H_d][hýE\\4 appears.
You can make or receive a call even when
the ringer is turned off. When you have an incoming call, any other phone connected to
the same line rings, and ?dYec_d]ý 9Wbb appears.
To turn the ringer back on, simply press VOL/
CID 8 or 9. The ringer is restored at the
H_d][h 7 >_]^ setting.
TURNING AUTO TALK ON/
OFF
Your phone is preset so you must press
TALK when you lift the handset from the base
to answer a call. With auto talk turned on,
you can answer a call by just lifting the handset from the base. If the handset is away
from the base, you can answer by pressing
any key.
Follow these steps to turn auto talk on or off.
1. Lift the handset and press MENU. A
menu appears with 7kjeýJWba selected.
2. Press SELECT/INTCM to change the auto
talk setting. Ed or E\\ appears indicating
the selected setting.
3. Return the handset to the base or press
MENU to store the new setting.
TURNING CALLER ID/CALL
WAITING ON/OFF
If you subscribe to Call Waiting with Caller ID
service, you can set the phone to show Caller ID information for an incoming call even
while you are using the phone.
Follow these steps to turn the Caller ID/ Call
Waiting feature on or off.
To set the base’s ringer volume, at any time
except during a call, repeatedly press RING
on the base until you get the desired setting
— high, low, or off. At off setting, the RINGER OFF indicator lights.
1. Lift the handset and press MENU. A
menu appears with 7kjeýJWba selected.
Note: When you set the base’s ringer off, the
base (and the handset if it is on the base)
does not ring but another phone connected
to the same line rings. If the handset is away
from the base, the handset also rings (unless
you set the handset’s ringer off).
3. Press SELECT/INTCM to change the
Caller ID/Call Waiting setting. Ed, E\\, or
Efj appears.
2. Press 2 or VOL/CID 9 to select 9?:9M
(Caller ID/Call Waiting).
4. Press MENU then return the handset to
the base to store the new setting.
Installation
13
With the Efj setting, you can use the advanced Caller ID/Call Waiting options. See
“Call Waiting Options Service” on Page 21.
STORING YOUR AREA
CODE
You can store your local area code in the
phone’s Caller ID record so it does not show
the area code if the received call is from your
local area. If you need to dial the area code
(or store it in the memory), you can add it afterwards. See “Adding/Deleting the Area
Code” on Page 23.
Note: If your calling area requires 10-digit dialing including area code, do not enter the
area code but leave this option blank.
Follow these steps to store your area code.
1. Lift the handset and press MENU.
2. Press 3 or VOL/CID
7h[Wý9eZ[.
9 twice to select
3. Press SELECT/INTCM, then enter your
three-digit area code. If you make a mistake, repeatedly press 6 or 7 to move
the cursor over the incorrect digit, then
enter the correct number.
Note: If an area code is already stored,
it appears on the display. To delete the
area code, press DELETE/CH three
times. Then enter your area code. Or
you can use 6 or 7 to move the cursor and edit the area code.
4. Press SELECT/INTCM to store the area
code, then press MENU or return the
handset to the base to clear the display.
14
Installation
ˆ Operation
MAKING AND RECEIVING
CALLS USING THE
HANDSET
ADJUSTING THE HANDSET
VOLUME
To make a call, lift the handset and press
TALK. Talk and the current volume setting
(see “Adjusting the Handset Volume”) appear on the handset’s display, and the
CHARGE/IN USE indicator on the base
lights. Then dial the number. The number
displays on the handset as you dial, then the
call’s elapsed time displays.
You can also dial the number before you
press TALK. If you make a mistake, press
DELETE/CH until the incorrect entry is
erased, then enter the correct number. To
delete the entire number, hold down DELETE/
CH for at least 2 seconds.
To adjust the volume of the sound you hear
through the handset during a call, press VOL/
CID 8 or 9 until you obtain the desired volume level. Lebkc[ CWn_ckc, Lebkc[
>_]^, Lebkc[ C[Z_kc, or Lebkc[ Bem appears
on the display.
Once you set the volume level, the setting is
maintained even after you hang up the
phone.
Note: When you press VOL/CID 8 while the
volume is maximum or VOL/CID 9 while the
volume is low, the setting does not change
and the phone beeps three times.
USING THE
SPEAKERPHONE
When you receive a call, ?dYec_d]ý 9Wbb appears on the display. To answer it, lift the
handset from the base and press TALK. If
auto talk is on, just lift the handset from the
base or press any key. JWba and the current
volume setting appear on the display.
To make or answer a call using the speakerphone, press SPEAKER. The SPEAKER indicator lights. When you hear a dial tone, dial
the number using the base’s keypad.
To end a call, place the handset on the base
or press TALK.
To set the speakerphone’s volume, press
VOL 8 or 9 on the base.
SELECTING THE CHANNEL
To end a speakerphone call, press SPEAKER
again.
The phone has 20 channels. If the call
seems to disconnect for no reason during a
call, press DELETE/CH on the handset to select a different channel. IYWdd_d] appears
while your phone searches for a clear channel.
Switching Between the Handset
and Speakerphone
To switch to the speakerphone while you are
using the handset, press SPEAKER on the
base. When you hear the conversation or
dial tone on the speakerphone, press TALK
on the handset.
Operation
15
To switch to the handset while you are using
the speakerphone, simply lift the handset off
the base. If the handset is away from the
base, press TALK, then press SPEAKER.
Using Both the Handset and
Speakerphone
Then press TALK and the phone dials the
number.
To dial the last number dialed using the
base, press SPEAKER then REDIAL/PAUSE.
Notes:
• The redial memory for each keypad is
separate. You cannot redial a number
you dialed on the handset’s keypad
using REDIAL/PAUSE on the base’s keypad, and vice versa.
If someone else is using the speakerphone,
press TALK on the handset to join the conversation. If someone else is using the handset, press SPEAKER on the base to join the
conversation.
• On the handset, you can also press
REDIAL after pressing TALK to dial the
last number dialed.
During the call, one person can hang up and
another person can continue the call at the
other keypad. Or, both people can hang up
at the same time to end the call.
• The redial memory holds up to 32 digits,
so you can redial long-distance as well
as local numbers.
Note: If you hear a high-pitched noise from
the base’s speaker, the handset and the
base are too close together.
• The redial memory also holds pause
entries. See “Entering a Pause” on
Page 19.
USING MUTE
While talking on the speakerphone, you can
temporarily turn off the phone’s microphone
by pressing MUTE so the other party cannot
hear you. The SPEAKER indicator flashes.
Press MUTE or SPEAKER to resume your
conversation.
Note: If the phone is close to loud noises
while you are using the speakerphone, the
phone might not switch to let you hear the
person on the other end of the line. If this
happens, press MUTE to turn off the microphone so you can hear the caller. Press
MUTE again to speak.
USING FLASH
FLASH performs the electronic equivalent of
a switchhook operation for special services,
such as Call Waiting.
For example, if you have Call Waiting, press
FLASH to answer an incoming call without
disconnecting the current call. Press FLASH
again to return to the first call.
Note: If you do not have any special phone
services, pressing FLASH might disconnect
the current call.
USING REDIAL
USING TONE SERVICES ON
A PULSE LINE
You can quickly dial any of the last three
numbers you dialed recently on the handset.
Lift the handset and repeatedly press REDIAL until the number you wish to dial displays.
Some special services, such as bank-byphone, require tone signals. If you have
pulse service, you can still use these special
tone services.
16
Operation
Dial the service’s main number. When the
service answers, press TONE/∗. Any additional numbers you dial are sent as tone signals.
When you hang up, the phone automatically
resets to pulse dialing.
Transferring a Call Between the
Handset and Base
You can use the phone’s intercom feature to
transfer a call between the handset and the
base.
To transfer a call from the handset to the
base, press SELECT/INTCM. The call is put
on hold, and FW]_d]ý8Wi[ and >ebZ appear.
USING PAGE/INTERCOM
You can use the phone as a two-way pager
and intercom between the base and the
handset. This is useful if the handset is away
from the base and you want to locate it, or if
you want to converse with someone through
the intercom.
To page the base from the handset, press
SELECT/INTCM. FW]_d]ý8Wi[ appears, and the
base and handset ring. Press SPEAKER or
INTCM on the base to answer the page. ?dj[h#
Yec appears on the handset’s display.
To page the handset from the base, press INTCM on the base. The handset and base
ring, and FW]_d] appears on the handset’s
display. Press TALK or SELECT/INTCM on the
handset to answer the page. ?dj[hYec appears.
To end an intercom call, press TALK on the
handset, press SPEAKER on the base, or
hang up the handset.
If a call comes in during an intercom conversation, the base rings even if you set the
base’s ringer to off. Either the person at the
base or the person at the handset can answer the call. Press TALK on the handset or
SPEAKER on the base once to end the intercom call, then press TALK or SPEAKER again
to answer the incoming call.
When the person at the base answers, press
TALK. The call is released from hold and
transferred to the base.
To return to handset use, press TALK again.
To transfer a call from the base to the handset, press INTCM on the base. The call is
placed on hold, and FW]_d] and >ebZ appear
on the handset’s display. When the person
with the handset answers, press SPEAKER.
The call is released from hold and transferred to the handset. To return to base use,
press SPEAKER again.
MEMORY DIALING
You can store up to 30 numbers in memory
(20 in the handset’s and 10 in the base’s
memory), then dial a stored number by
pressing a memory location number.
You can also store a name with each number
in the handset’s memory.
Use the supplied memory directory sticker to
record your stored numbers. Peel the backing from the sticker and attach it to the
base’s cradle.
Operation
17
Storing a Number in the Handset’s
Memory
To enter two letters from the same key in
a row, press FLASH/7 to move the cursor to the next position. For example to
enter AB, press 2; 7 appears. Then
press FLASH/7, the cursor moves to
the next position, then press 2 twice so 8
appears.
Notes:
• The phone beeps five times and exits
the storing process if you wait more than
20 seconds between each keypress.
To enter a space, press FLASH/7 twice
without entering any character.
• If you receive a call during memory
entry, the phone exits the storing process.
To enter a number, repeatedly press the
corresponding number key until the
number appears.
Follow these steps to store a number in the
handset’s memory.
To enter special character, use 0. Each
time you press 0, the following characters appear in this order:
1. Lift the handset.
2. Hold down MEM until C[cehoýIjeh[ and a
list of memory location numbers appear.
∗ # – & ( ) (space) 0
If you make a mistake, use REDIAL/6
or FLASH/7 to move the cursor over
the error, then enter the correct character, or press DELETE/CH to delete a
character. To delete all characters, hold
down DELETE/CH for at least 1 second.
3. Press a number (01–20) or repeatedly
press VOL/CID 8 or 9 to choose a
two-digit memory location. Precede a
single digit location number with 0–01,
02, 03, and so on.
4. Press SELECT/INTCM. Ijeh[ DWc[
appears. If you do not want to enter a
name, skip to Step 6.
5. To enter a name, use the number keys.
Refer to the letters on the number keys
to select the desired letter. Press the key
once for the first letter in the upper case,
press twice for the second letter in the
upper case, and so on. To enter the
lower case letter, press four times (or
five times) to display the first letter in
lower case, five or six times for the second letter, and so on.
For example, to enter John: press 5
once; upper case @ appears. Then press
6 six times; lower case e appears. Press
4 five times; lower case ^ appears.
Finally, press 6 five times; lower case d
appears.
18
6. Press SELECT/INTCM.
appears.
Ijeh[ý DkcX[h
7. Enter the phone number and any tone or
pause entries (see “Using Tone Services
On a Pulse Line” on Page 16 and
“Entering a Pause” on Page 19).
8. Press SELECT/INTCM. The phone beeps
and C[cehoddý Ijeh[Z appears. After 2
seconds, C[ceho Ijeh[ appears. Repeat
Steps 3–8 to store more numbers.
9. When you finish, press MEM.
To replace a stored number, store a new one
in its place.
Operation
Editing or Deleting a Number in
the Handset’s Memory
Tone Services On a Pulse Line” on
Page 16 and “Entering a Pause”).
Follow these steps to edit or delete a memory number.
Notes:
1. Lift the handset.
• The phone beeps five times and the
phone exits the storing process if you
enter more than 20 digits.
2. Hold down MEM until C[cehoýIjeh[ and a
list of memory location numbers appear
on the display.
• Each tone or pause entry uses one digit
of memory.
3. Choose a memory location (01–20) by
pressing a number or by repeatedly
pressing VOL/CID 8 or 9.
4. Press SELECT/INTCM. A menu appears
with the three options listed below.
Press VOL/CID 8 or 9 to highlight the
desired option then press SELECT/
INTCM to choose it.
3. Press MEMORY again, then enter the
memory location number (0–9) where
you want to store the phone number. A
tone sounds indicating that the number
is stored.
described in Steps 5 through 8 of “Storing a Number in the Handset’s Memory”.
To replace a number in the base’s memory,
simply store a new number in its place. To
erase a memory number, press MEMORY
twice, then press the memory location number (0–9) you want to erase. A tone sounds
indicating that the memory location has been
erased.
:[b[j[ýC[cehodd — the display prompts
Entering a Pause
;Z_jý C[cehodd — edit the record as
you to confirm the deletion. Press VOL/
CID 8 to move the cursor to O[i, then
press SELECT/INTCM or DELETE/CH.
The phone beeps, and C[cehoddý:[b[j[Z
appears.
=eý8WYa — returns you to the list of memory numbers.
Storing a Number in the Base’s
Memory
Note: The phone beeps five times and the
phone exits the storing process if you wait
more than 20 seconds between each keypress.
1. Press MEMORY. The CHARGE/IN USE
indicator blinks.
2. Enter the number (up to 20 digits) and
any tone or pause entries (see “Using
In some telephone systems, you must dial an
access code (9, for example) and wait for a
second dial tone before you can dial an outside number. You can store the access code
with the phone number. However, you
should also store a pause after the access
code to allow the outside line time to connect. To enter a 2-second pause, press
PAUSE (REDIAL/PAUSE on the base). F appears on the display if you are storing a number into the handset’s memory. You can add
more pause entries for a longer pause.
Reviewing the Handset’s Memory
Numbers
To review your handset’s memory numbers,
press MEM. The list of memory location numbers (&'–(&) appears with the name stored
Operation
19
with each number (or 2C[cehodd4 if you did
not store a name).
To see the stored phone numbers, press 7.
An arrow to the right of the number means it
is longer than 13 digits. Press 7 again to
see the rest of the number. Repeatedly press
6 to return to the name display.
To exit the memory number list, press MEM.
To see a stored name and phone number at
the same time, press SELECT/INTCM when
the cursor is by a memory location number.
To exit this display, hold down DELETE/CH
until the display clears.
Dialing a Memory Number
To dial a number stored in the handset’s
memory, lift the handset and press MEM. The
list of memory location numbers appears.
Choose a memory location (01–20) by pressing a number or by repeatedly pressing VOL/
CID 8 or 9, then press TALK.
Testing Stored
Emergency Numbers
If you store an emergency service’s number
(police department, fire department, ambulance) and you choose to test the stored
number, make the test call during the late
evening or early morning hours to avoid peak
demand periods. Also, remain on the line to
explain the reason for your call.
USING A HEADSET
You can talk with handsfree convenience using an optional headset that has a 3/32–inch
(2.5-mm) plug. Contact your local RadioShack store for a suitable headset.
To connect the headset, open the rubber
cover on the side of the handset, then insert
the headset’s plug into the jack.
Notes:
• Connecting a headset disconnects the
handset’s earpiece and microphone.
To dial a number stored in the base’s memory, press SPEAKER. When you hear a dial
tone, press MEMORY, then press the memory
location number for the number you want to
dial.
• VOL/CID 8 or 9 on the handset also
controls the connected headset’s volume.
• If you place the handset on the base to
recharge it while the headset is connected, be sure the handset seats properly.
Note: If you select an empty memory location, the base beeps.
Chain-Dialing Service Numbers
For quick recall of numbers for special services (such as bank by phone), store each
group of numbers in its own memory location. Dial the service’s main number first.
Then, at the appropriate place in the call,
press MEM (MEMORY on the base) and the
number for the location where the additional
information is stored.
20
With a headset connected, you can make or
answer calls as usual using the speakerphone or the keys on the handset.
You can use a handset holder (available
from your local RadioShack store) to hang
the handset on your belt for greater convenience.
When you finish using the headset, disconnect it from the handset and close the rubber
cover to protect the jack.
Operation
ˆ Caller ID Operation
If you subscribe to Caller ID service from
your phone company, the phone company
sends information about the call, as well as
the time and date, between the first and second rings of every call you receive.
Before you can use the Call Waiting Options
Services, you must:
The phone displays this information after the
second ring, and it stores up to 50 Caller ID
records for later review. It also shows if caller
information is unavailable or if the name and
number were blocked by the caller (see
“Caller ID Messages” on Page 23).
• set the Caller ID/Call Waiting feature to
Opt (see “Turning Caller ID/Call Waiting
On/Off” on Page 13).
If the phone’s Caller ID memory becomes
full, any new call replaces the oldest call’s
record.
If you subscribe to Call Waiting with Caller
ID, you will hear a tone through the handset
when a call comes in, then the Caller ID
record appears. If you want to answer the incoming call, press FLASH. To resume the
previous phone conversation, press FLASH
again.
Note: When you are using the speakerphone, the call waiting tone sounds from the
base’s speaker and the handset’s display
shows the Caller ID information when the
second call comes in. You can press FLASH
on the base to alternate between calls.
CALL WAITING OPTIONS
SERVICE
You can also subscribe to Call Waiting Options Service from your phone company.
This service provides you with more choices
on how to handle a second call when you are
already on the phone. You can switch between the callers, have a 3-way conference
call with both callers, send the second caller
to your voice mail, or answer the second caller with a prerecorded message to hold the
line.
• subscribe to the Options service from
your telephone company.
Using Call Waiting Options
Note: The phone beeps five times and exits
the menu mode if you wait more than 20 seconds between each keypress.
You hear a soft beep when a call comes in
while you are already on the phone. The display shows the caller name and phone number.
Follow these steps to use Call Waiting Options Services.
1. Press MENU. A list of several options,
beginning with 7iaýjeý>ebZ appears.
2. Repeatedly press VOL/CID 9 to scroll
through the options list. You can also
press the number of the desired option.
3. Choose one of the following options,
then press SELECT/INTCM.
7iaýjeý>ebZ — A waiting caller hears a prerecorded message stating that you will be
available shortly, and is put on hold. 9Wbbý>ebZ#
_d] appears on your phone.
J[bbý8kio — A prerecorded message indicates
you are busy, and the waiting call is disconnected. JebZý8kio appears on your phone.
JWa[ýC[iiW][ — Send a waiting caller to your
phone company’s voice mail service. JeýLe_Y[
CW_b appears on your phone.
Caller ID Operation
21
Note: Voice Mail is a service available from
some telephone companies. A call for a subscriber can be kept at the telephone company and retrieved later on by calling the
special number and entering the caller’s
phone number and code number. Check with
your telephone company to determine if this
service is available.
7dim[h%:hefý ' — Disconnects the first call,
and connects automatically to the new caller.
7dim[h%:hefý'ij appears.
Press SELECT/INTCM.
Using Conference
You can either begin a conference call as
soon as you receive a second call, or after
the second caller has been on hold for a
while (see “Using Ask to Hold”).
Once you have established a conference
call, you can end it at any time by dropping
one of the calls.
9ed\[h[dY[ — Allows you to speak with your
first and second callers to have a 3-way conference call. 9ed\[h[dY[Z appears.
:hefý <_hij — hang up on the first caller and
:hefý <_hijý WdZý :hefý BWij are options you can
continue with the first.
only use with a conference call (see “Using
Conference”).
:hefýBWij — hang up on the second caller and
Follow these steps to drop one of the calls.
1. To end a conference call, press MENU.
Using Ask to Hold
When you select 7iaý jeý >ebZ, you can then
use several of the other options.
1. If you decide you cannot end your first
call, and you do not want to continue to
leave the second call on hold, press
MENU.
To notify the second caller that you are
busy, scroll down to J[bbý8kio or press 2.
To send the second caller to voice mail
(if you have voice mail), scroll down to
JWa[ýC[iiW][ or press 3.
Press SELECT/INTCM.
2. If you decide to take the second call,
and end the first, scroll down to 7dim[h%
:hefý' or press 4.
Press SELECT/INTCM.
3. If you decide to include the second
caller in your conversation with the first
caller, scroll down to 9ed\[h[dY[ or press
5.
22
continue with the second.
2. Scroll down to :hefý<_hij (or press 6) or
:hefýBWij (or press 7) to drop the desired
call.
3. Press SELECT/INTCM.
appears on your phone.
9Wbbý :heff[Z
REVIEWING CALLER ID
RECORDS
If the handset is faceup on the base, it shows
the number of new Caller ID records, if any,
and the total number of records.
To review the contents of each Caller ID
record, lift the handset and press CID to recall the number of records on the display.
Then, repeatedly press VOL/CID 9 to scroll
through the Caller ID records from the newest to the oldest, or VOL/CID 8 to scroll back
through the records. To scroll quickly through
the records, hold down VOL/CID 8 or 9.
When you scroll past the last record, total
record number appears, then the first record.
Caller ID Operation
When you scroll past the first record, the total
record number appears, then the last record.
code. Pressing 3 again deletes or adds the
area code.
The top line of each record shows the date,
time and the number of calls from that number. The second line shows the caller’s
name, and the third line shows the caller’s
phone number.
When you dial the number or store it into
memory, the phone dials or stores the number as it appears on the display.
To exit the Caller ID record display, press
CID.
Caller ID Messages
Display
Description
D[m0ýNN
JejWb0NN
Shows the number of
new Caller ID records
(records you have not
reviewed) and the total
number of records.
Fh_lWj[ýDWc[
The caller has blocked
the Caller ID information.
or
Fh_lWj[ýDkcX[h
KdademdýDWc[
or
KdademdýDkcX[h
?dYecfb[j[ý:WjW
The caller is not within a
Caller ID service area.
Appears if there was an
error during transmission
of Caller ID information.
Occasional errors are
normal. If the phone frequently displays ?dYec#
fb[j[ :WjW, contact your
local phone company or
RadioShack store.
DIALING NUMBERS FROM A
CALLER ID RECORD
To dial a local number stored in a Caller ID
record, recall the record, then press TALK. If
it is a long distance call, press 1 (' appears
before the displayed number) before you
press TALK. If you want to add or delete the
area code, press 3 before you press TALK.
Note: If a Caller ID record does not contain a
phone number (if it was blocked by the caller,
for example) you cannot dial from that
record.
STORING A CALLER ID
RECORD TO MEMORY
Follow these steps to store the name and
number from a Caller ID record into a memory location.
1. Press CID then VOL/CID 8 or 9 to
recall the record you want to store.
If it is a long distance number, press 1.
If you want to add or delete the area
code, press 3.
2. Press MEM. I[b[YjýBeYWj_ed appears.
ADDING/DELETING THE
AREA CODE
When the area code of the received call is
the same as the one you stored (see “Storing
Your Area Code” on Page 14), the caller ID
record does not show the area code. If it is
different, the record shows the area code.
However, you can add or delete the area
code on the display. When the record is on
the display, press 3 to add or delete the area
3. Choose a memory location (01–20) by
pressing a number or by repeatedly
pressing VOL/CID 8 or 9, then press
SELECT/INTCM.
If the selected location is empty, the phone
beeps to confirm that it stored the number,
then the Caller ID record appears.
Caller ID Operation
23
If a record exists in the selected location, H[#
fbWY[ý C[ceho5 appears, prompting you to
confirm the replacement. Move the cursor to
O[i or De, then press SELECT/INTCM.
DELETING CALLER ID
RECORDS
You can delete Caller ID records individually
or all at once.
Follow these steps to delete a single Caller
ID record.
1. Press CID then VOL/CID 8 or 9 to
recall the record you want to delete.
2. Press DELETE/CH. :[b[j[ý C[iiW][5
appears, prompting you to confirm the
deletion.
3. Press VOL/CID 8 to move the cursor to
O[i, then press SELECT/INTCM or
DELETE/CH. The phone beeps once
indicating that the record was deleted.
Deleting All Caller ID Records
Follow these steps to delete all Caller ID
records.
1. Press CID so the record totals appear.
2. Press DELETE/CH. :[b[j[ý 7bb5 appears,
prompting you to confirm the deletion.
3. Press VOL/CID 8 to move the cursor to
O[i, then press SELECT/INTCM or
DELETE/CH. The phone beeps once and
JejWb0&& appears indicating that all Caller
ID records were deleted.
24
Caller ID Operation
ˆ Troubleshooting
We do not expect you to have any problems with your phone, but if you do, these suggestions
might help.
Problem
The phone does not work or works poorly.
Suggestion
Be sure the base’s phone line cord and AC adapter are
correctly and securely connected.
Be sure the battery pack in the handset is connected and
charged.
Return the handset to the base for about 5 seconds to
reset the security access-protection code.
The handset stops working or works poorly
during a call.
Move the handset closer to the base.
Lift the base’s antenna to a fully vertical position.
Be sure the handset’s battery pack is charged. (If the battery pack power is too low, the handset cannot display
Bemý8Wjj[ho.)
Low volume or unusual sounds.
Someone has picked up another phone on the same line.
Hang up the other phone.
Dropout or mute.
Keep the handset away from computers, remote control
toys, wireless microphones, alarm systems, intercoms,
room monitors, fluorescent lights, and electrical appliances.
Move to another location or turn off the source of interference.
Press DELETE/CH to change the channel.
Hang up and redial the number.
The phone cannot be operated at a useful
distance from the base because the signal
becomes weak or noisy (handset’s range
has decreased).
Be sure neither the handset’s nor base’s antenna is
touching a metal surface.
Return the handset to the base and recharge the battery
pack.
Lift the base’s antenna to a vertical position.
The handset battery pack does not charge.
Check the charging contacts on the handset and base. If
they are dirty, clean them with a pencil eraser.
Be sure the battery pack is connected correctly.
Be sure the handset is properly seated on the base.
Replace the battery pack (see “Connecting, Charging,
and Replacing the Battery Pack” on Page 11).
Troubleshooting
25
Problem
The handset does not ring or receive a
page.
Suggestion
Move the handset closer to the base.
Lift the base’s antenna to a vertical position.
Be sure the battery pack in the handset is connected and
charged.
Move the base away from other electrical devices.
You have an incoming call, but do not
receive any Caller ID information.
Let the phone ring twice before you answer so the phone
has time to record the Caller ID information.
Check that the phone is correctly and securely connected.
Check with your phone company to verify that your Caller
ID service is active.
If you still have problems, disconnect the phone. If other phones on the same line work properly, the fault is in this phone or its installation. If you cannot find the problem, take the phone to
your local RadioShack store for assistance.
CARE
Keep the phone dry. If it gets wet, wipe it dry
immediately. Use and store the phone only in
normal temperature environments. Handle
the phone gently and carefully. Do not drop
it. Keep the phone away from dust and dirt.
Wipe the phone with a damp cloth occasionally to keep it looking new.
Modifying or tampering with the phone’s internal components can cause a malfunction
and might invalidate its warranty and void
your FCC authorization to operate it. If your
phone is not performing as it should, take it
to your local RadioShack store for assistance. If the trouble is affecting the telephone
lines, the phone company can ask you to disconnect your phone until you have resolved
the problem.
26
Troubleshooting
ˆ Notes
Notes
27
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
RadioShack Corporation
Fort Worth, Texas 76102
12/99
43-3515
UCZZ01713ZZ
06A01
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement