Crestron | TSS-752 | Configuration Guide: TSS-752

Configuration Guide: TSS-752
Crestron TSS-752
7” Room Scheduling Touch Screen
Configuration Guide
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, Rava, and RoomView are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States
and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming
the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for
errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2014 Crestron Electronics, Inc.
Crestron TSS-752
7” Room Scheduling Touch Screen
Contents
7” Room Scheduling Touch Screen: TSS-752
1
Access the Setup Screens ........................................................................................................... 1
Configure the Touch Screen ...................................................................................................... 3
Ethernet Setup ............................................................................................................. 3
IP Table Setup ............................................................................................................. 5
Audio Setup ................................................................................................................. 7
Display Setup .............................................................................................................. 7
Standby Timeout ......................................................................................................... 8
Diagnostics .................................................................................................................. 9
About ......................................................................................................................... 14
Save & Exit ............................................................................................................... 14
Configuration Guide – DOC. 7602A
Contents • i
Crestron TSS-752
7” Room Scheduling Touch Screen
7” Room Scheduling
Touch Screen: TSS-752
Access the Setup Screens
The “TSS-752 Setup” menu is the starting point for configuring the TSS-752 Room
Scheduling Touch Screen from Crestron®.
NOTE: If no project has been loaded or if an invalid project has been loaded, the
TSS-752 displays a message instructing the user to touch the screen to enter the
setup menus.
The setup screens enable basic configuration procedures prior to regular operation of
the touch screen. To access the setup screens after the TSS-752 boots up to the
RoomView® Scheduling “Offline” screen, touch “hard keys” 1, 2, 3, and 4, to the
right of the touch screen display, in sequence twice (touch 1, 2, 3, 4, 1, 2, 3, 4) within
a 5-second period.
Button Numbering
1
2
3
4
Configuration Guide – DOC. 7602A
7” Room Scheduling Touch Screen: TSS-752 • 1
7” Room Scheduling Touch Screen
Crestron TSS-752
The “TSS-752 Setup” menu is displayed.
“TSS-752 Setup” Menu
The “TSS-752 Setup menu” is comprised of buttons for Ethernet Setup, IP Table
Setup, Audio Setup, Display Setup, Standby Timeout and Diagnostics. In
addition, there is a User Project Mode On button to toggle the RoomView
Scheduling interface, an About button that provides information about the touch
screen and a Save & Exit button. The functions are detailed in the next section of
this guide.
2 • 7” Room Scheduling Touch Screen: TSS-752
Configuration Guide – DOC. 7602A
Crestron TSS-752
7” Room Scheduling Touch Screen
Configure the Touch Screen
Ethernet Setup
On the “TSS-752 Setup” menu, touch Ethernet Setup to display the “Ethernet
Setup” menu.
“Ethernet Setup” Menu
The “Ethernet Setup” menu displays the touch screen’s MAC address and IP
Address, Subnet Mask, Def Router, Primary DNS, Secondary DNS, Hostname and
Domain. There are controls for turning DHCP On or Off as well as a Set Static IP
Address Settings button, which provides access to controls which allow editing of
these settings. This screen also contains a Link indicator to show the status of the
Ethernet connection.
NOTE: Crestron recommends using a static IP address for anything other than
testing.
DHCP is enabled by default. To change to a static IP address, touch Off under
DHCP Enabled, then touch Set Static IP Address Settings to display the “Ethernet
Setup – Static IPs” screen.
Configuration Guide – DOC. 7602A
7” Room Scheduling Touch Screen: TSS-752 • 3
Crestron TSS-752
7” Room Scheduling Touch Screen
“Ethernet Setup – Static IPs” Screen
To edit the Static IP Address, Static Subnet Mask, Static Default Router, Preferred
DNS or Alternate Preferred DNS, touch the button directly under the label for the
entry to edit. The on-screen numeric keypad opens.
On-Screen Numeric Keypad
Use the keypad to make the new entry. Touch the “x” in the text field to clear any
previous entry. Touch
or
to delete the last digit. Touch Save to save a new entry
to return to the “Ethernet Setup – Static IPs” screen.
After new settings have been saved, touch Reboot Required to Apply IP Changes
on the “Ethernet Setup – Static IPs” screen to reboot the touch screen, so the new
settings can take effect.
If not making any changes, touch
Touch
to return to the “Ethernet Setup” menu.
again to return to the “TSS-752 Setup” menu.
4 • 7” Room Scheduling Touch Screen: TSS-752
Configuration Guide – DOC. 7602A
Crestron TSS-752
7” Room Scheduling Touch Screen
IP Table Setup
On the “TSS-752 Setup” menu, touch IP Table Setup to display the “Ethernet Setup
– IP Table” menu.
“Ethernet Setup –IP Table” Menu
NOTE: This step should not be performed when the TSS-752 is being used for
RoomView scheduling, as having an IP table entry will prevent the project from
starting up.
The “Ethernet Setup – IP Table” menu displays up to four IP table settings, each of
which has an Online indicator. To add or edit an entry, touch the Add/Edit button to
its left. The “Ethernet Setup – Edit IP Table Entry” screen is displayed.
“Ethernet Setup –Edit IP Table Entry” Screen
Touch the field below CIP ID to display the on-screen hex keypad.
Configuration Guide – DOC. 7602A
7” Room Scheduling Touch Screen: TSS-752 • 5
Crestron TSS-752
7” Room Scheduling Touch Screen
On-Screen Hex Keypad
Use the keypad to make the new entry. Touch the “x” in the text field to clear any
previous entry. Touch
or
to delete the last digit. Touch Save to save a new entry
to return to the “Ethernet Setup – Edit IP Table Entry” screen.
Touch the field below IP Address/Hostname to display the on-screen keyboard.
On-Screen Keyboard
Use the keyboard to make the new entry. Touch Cancel to return to the “Ethernet
Setup – Edit IP Table Entry” screen. Touch the “x” in the text field to clear any
to delete the last digit. Touch Save to save a new entry
previous entry. Touch
and return to the “Ethernet Setup – Edit IP Table Entry” screen.
On the “Ethernet Setup – Edit IP Table Entry” screen, touch Save Entry to save the
current entry or Delete Entry to clear it.
If not making any changes, touch
Table” menu.
Touch
to return to the “Ethernet Setup –IP
again to return to the “TSS-752 Setup” menu.
6 • 7” Room Scheduling Touch Screen: TSS-752
Configuration Guide – DOC. 7602A
Crestron TSS-752
7” Room Scheduling Touch Screen
Audio Setup
On the “TSS-752 Setup” menu, touch Audio Setup to display the “Audio Setup”
screen.
“Audio Setup” Screen
The “Audio Setup” screen provides controls for muting (or unmuting) the audio,
adjusting level for both Master Volume and Media Volume, as well as a control for
playing a test .wav file. The Media Volume controls adjust H.264 streaming media
level in relation to the Master Volume controls.
Touch
to return to the “TSS-752 Setup” menu.
Display Setup
On the “TSS-752 Setup” menu, touch Display Setup to enter the “Display Setup”
screen.
“Display Setup” Screen
The “Display Setup” screen provides controls for LCD (Screen) Brightness, Blue
Key Brightness, Green Key Brightness, Red Key Brightness, and On and Off controls
for Hard Key Wakes LCD. In addition there are Off, Red, Green, and Blue controls
for each bank of LEDs.
Configuration Guide – DOC. 7602A
7” Room Scheduling Touch Screen: TSS-752 • 7
Crestron TSS-752
7” Room Scheduling Touch Screen
Touch
to return to the “TSS-752 Setup” menu.
Standby Timeout
On the “TSS-752 Setup” menu, touch Standby Timeout to display the “Standby
Timeout” menu.
“Standby Timeout” Menu
The “Standby Timeout” menu provides controls to adjust standby timeout from 0 to
120 minutes. There is also a Screen Saver Options button which opens the “Standby
– Screen Saver” screen.
“Standby – Screen Saver” Screen
The “Standby – Screen Saver” screen provides controls to turn the Clock Screen
Saver On and Off as well as controls to display the time in a 24 Hour format and to
adjust the Screen Saver Brightness.
Touch
to return to the “Standby Timeout” menu.
Touch
again to return to the “TSS-752 Setup” menu.
8 • 7” Room Scheduling Touch Screen: TSS-752
Configuration Guide – DOC. 7602A
Crestron TSS-752
7” Room Scheduling Touch Screen
Diagnostics
On the “TSS-752 Setup” menu, touch Diagnostics to display the “Diagnostics”
menu.
“Diagnostics” Menu
The “Diagnostics” menu displays the CPU temperature, Available Memory and
contains controls to run a Keypad Test, Touch Test, Mic Test, LAN Test, Rava
Test, and RTSP Test. In addition is a control to open various test pattern screens.
These are explained in the paragraphs that follow.
Keypad Test
On the “Diagnostics” menu, touch Keypad Test to display the “Diagnostics –
Keypad Test” screen.
“Diagnostics – Keypad Test” Screen
The “Diagnostics - Keypad” screen can be used to test the function of the hard key
push buttons. When a button is pressed, its corresponding indication on the screen
lights.
Touch
Configuration Guide – DOC. 7602A
to return to the “Diagnostics” menu.
7” Room Scheduling Touch Screen: TSS-752 • 9
Crestron TSS-752
7” Room Scheduling Touch Screen
Touch Test
On the “Diagnostics” menu, touch Touch Test to display the touch test screen.
Touch Test Screen
The touch test screen can be used to test the function of the screen. When a location
button (the “x” buttons or the “o” button) is touched, its indication on the screen
lights.
Touch
to return to the “Diagnostics” menu.
Mic Test
On the “Diagnostics” menu, touch Mic Test to begin a microphone test. The touch
screen records audio for five seconds and then plays back the recorded sound.
The built-in microphone (located on the left side of the top of the touch screen) is
used to record your voice and play it back to confirm the microphone is functioning.
When playback is finished, the display returns to the “Diagnostics” menu.
10 • 7” Room Scheduling Touch Screen: TSS-752
Configuration Guide – DOC. 7602A
Crestron TSS-752
7” Room Scheduling Touch Screen
LAN Test
On the “Diagnostics” menu, touch LAN Test to display the “Diagnostics – LAN”
screen.
“Diagnostics – LAN” Screen
The “Diagnostics – LAN” screen displays the touch screen’s MAC address and IP
Address, Subnet Mask, Def Router, Primary DNS, Secondary DNS, Hostname and
Domain. This screen also contains a Link indicator to show the status of the Ethernet
connection and controls to test the connection to the default router.
Touch
to return to the “Diagnostics” menu.
Test Patterns
On the “Diagnostics” menu, touch Test Patterns to display the “Diagnostics - Test
Patterns” screen.
“Diagnostics - Test Patterns” Screen
The “Diagnostics - Test Patterns” screen contains buttons for selecting the different
available test patterns: Display Color Bars, Display Vertical Lines, Display Gray
Scale, Display Grid Pattern and Display Test Pattern.
Configuration Guide – DOC. 7602A
7” Room Scheduling Touch Screen: TSS-752 • 11
Crestron TSS-752
7” Room Scheduling Touch Screen
Touch
to return to the “Diagnostics” menu.
Rava Test
On the “Diagnostics” menu, touch Rava Test to display the “Diagnostics – Rava”
menu.
“Diagnostics - Rava” Menu
The “Diagnostics - Rava” menu provides controls for testing the use of Crestron’s
Rava™ SIP Intercom with the TSS-752. They can be used to test projects and
settings. If the intercom works but the project does not, there is an issue with the
project; if the intercom does not work, there is an issue with the settings.
The Rava Setup button opens a second “Diagnostics – Rava” screen for Rava Setup.
“Diagnostics - Rava” (Rava Setup) Screen
This screen provides controls to switch between Peer to Peer Mode and SIP Server
Mode, and when in the latter, controls to switch between Normal Mode and Door
Mode. Touching the other fields on the screen opens the on-screen keyboard or onscreen numeric keypad, as appropriate.
When all settings have been entered, touch Apply to store them or Cancel to ignore
any changes. Touching either one returns the display to the “Diagnostics – Rava”
menu.
12 • 7” Room Scheduling Touch Screen: TSS-752
Configuration Guide – DOC. 7602A
Crestron TSS-752
7” Room Scheduling Touch Screen
Touch
to return to the “Diagnostics” menu.
Touch
again to return to the “TSS-752 Setup” menu.
RTSP Test
On the “Diagnostics” menu, touch RTSP Test to display the “Diagnostics – RTSP”
screen.
“Diagnostics - RTSP” Screen
The “Diagnostics – RTSP” screen tests whether Real Time Streaming Protocol is
functioning on the TSS-752. Touch the area below Source URL: (Touch to edit) to
open the on-screen keyboard. Enter the URL for an H.264 or MPEG4 video and
touch Save. The video is displayed on the right side of the “Diagnostics – RTSP”
screen.
Touch
to return to the “Diagnostics” menu.
Touch
again to return to the “TSS-752 Setup” menu.
Configuration Guide – DOC. 7602A
7” Room Scheduling Touch Screen: TSS-752 • 13
Crestron TSS-752
7” Room Scheduling Touch Screen
About
On the “TSS-752 Setup” menu, touch About to display the “About” screen.
“About” Screen
The “About” screen displays information about the touch screen, including the
currently loaded firmware and operating system versions.
Touch
to return to the “TSS-752 Setup” menu.
Save & Exit
On the “TSS-752 Setup” menu, touch Save & Exit to save all settings, exit the setup
screens and return to the main project.
14 • 7” Room Scheduling Touch Screen: TSS-752
Configuration Guide – DOC. 7602A
Crestron TSS-752
7” Room Scheduling Touch Screen
This page is intentionally left blank.
Configuration Guide – DOC. 7602A
7” Room Scheduling Touch Screen: TSS-752 • 15
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Configuration Guide – DOC. 7602A
(2038157)
01.14
Specifications subject to
change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising