Black & Decker | FSMH1621 | Technical data | Black & Decker FSMH1621 Technical data

Black & Decker FSMH1621 Technical data
FSMH1621
A
B
C
D
E
2
F
G
H
I
J
3
K
M
4
L
(Original instructions)
Intended use
Flexible hose and handle
Your Black & Decker steam mop has been designed for
sanitising and cleaning sealed hardwood, sealed laminate,
linoleum, vinyl, ceramic tile, stone and marble floors and for
refreshing carpets. This appliance is intended for indoor
household use only.
For convenient use of all accessories.
Warning! Read all of the 'Safety, Maintenance,
Service' manual carefully before operating
this appliance.
Read all of this manual carefully before operating
the appliance.
Variable steam jet nozzle
For higher pressure steam bursts, twist to change
the spray pattern of the steam burst.
Small brush (Blue)
Features
For cleaning bathrooms.
This appliance includes some or all of the following features.
1. ON/Off switch
2. Lock off button
3. Trigger switch
4. Steam nozzle
5. Hand held steam cleaner
6. AutoselectTM button
7. Filler cap
8. Water tank
9. Steam mop body
10. Handle
11. Steam head
12. Steam head cleaning pad
13. Resting mat
14. Carpet glider
15. Bottom cable tidy hook
16. Top cable tidy hook
17. Cable management clip
18. Jug
Accessories
This appliance includes some of the following accessories
others are available to purchase from the Black & Decker
website.
The performance of your appliance depends on the accessory
used. Black & Decker accessories are engineered to high
quality standards and designed to enhance the performance
of your appliance. By using these accessories you will get the
very best from your appliance.
ENGLISH
Small brush (Yellow)
For cleaning kitchens.
Small brush (Green)
For cleaning toilets.
Small Squeegee
For cleaning glass doors and windows.
Warning! Do not use the window squeegee on cold
glass. It may cause the glass to break.
Assembly
Warning! Before attempting any of the following operations,
make sure that the appliance is switched off and unplugged
and that the appliance is cold and does not contain any water.
Attaching the handle (Fig. A)
u
Slide the bottom end of the handle (10) into the top end of
the steam mop body (9) until it clicks into place. The arrow
on the handle (10) should be aligned with the top of the
steam mop body (9).
Attaching the steam head (Fig. B)
u
Slide the bottom end of the steam mop body (9) onto the
u
The steam head can be removed from the Steam mop
steam head (11) until it clicks into place.
body by pressing the steam head release button (19) and
pulling the steam mop body (9) off the steam head (11).
5
ENGLISH
(Original instructions)
Attaching the hand held steam cleaner (Fig. C)
u
Holding the back of the steam mop body (9) Push the
hand held steam cleaner (5) firmly into the steam mop
body (9) until it clicks into place.
Caution! Always ensure the handle command lights up to
confirm the unit is docked.
Warning! Inspect that the seal (22 Fig. H) on the steam nozzle (4) before fitting the hand held steam mop to the steam
mop body. If the seal is missing or damaged then please
contact your nearest authorised repair agent. Do not use the
appliance.
Removing the hand held steam cleaner (Fig. C)
u
Push the release button (19) down and pull the hand held
steam cleaner (5) away from the steam mop body
Attaching a cleaning pad (Fig. D)
Replacement cleaning pads are available from your Black &
Decker dealer:Steam head cleaning pad - cat. no. FSMP20-XJ).
u Place a cleaning pad (12) on the floor with the ‘hook &
loop’ side facing up.
u Lightly press the steam mop down onto the cleaning pad
(12).
Caution! Always place your steam mop on the resting mat
(13) with the handle (10) in the upright position when stationary and make sure the steam mop is turned off when not in
use.
Removing a cleaning pad (Fig. E)
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop. Do not wear slippers or
open toed footwear.
u Return the handle (10) to the upright position and turn the
steam mop ‘OFF’.
u Place the steam mop on the resting mat and wait until it
cools down. (approximately five minutes)
u Place the front of your shoe onto the cleaning pad removal
tab (21) and press down firmly.
u Lift the steam mop up off the cleaning pad.
Caution! Always place the steam mop on the resting mat (13)
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
Filling the water tank (Fig. F)
This Steam cleaner incorporates an anti-calc system to help
prolong the life of the system.
Note: Fill the water tank with clean tap water.
Note: In areas of very hard water, the use of de-ionised water
is recommended.
u Open the filler cap (7) by flipping it down.
u Using the jug, fill the water tank (8) with water.
6
Warning! Your water tank has a 0.35 litre capacity.
u Re-fit the filler cap (7).
Note: Ensure the filler cap is firmly secured.
Note: When not in use, the jug (18) may be clipped to the
handle for convenient storage.
Note: Do not use chemical cleaners with your steam mop..
Attaching the carpet glider (Fig. G) (For use on
carpets only)
Place carpet glider on the floor.
Attach a cleaning pad to the unit.
u Lightly press the steam mop down onto the carpet glider
u
u
(14) until it clicks into place.
Caution! Always place the steam mop on the resting mat (13)
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
Removing the carpet glider (Fig. G)
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
u Return the handle (10) to the upright position and turn the
steam mop ‘OFF’.
u Place the steam mop on the resting mat and wait until it
cools down. (approximately five minutes)
u Place the front of your shoe onto the carpet glider removal
tab (33) and press down firmly.
u Lift the steam mop up off the carpet glider (14).
Caution! Always place the steam mop on the resting mat (13)
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
Attaching the hose and accessories to the Hand
held steam cleaner (Fig. H & I)
Warning! Inspect the seal (22) on the steam nozzle (4) and
hose (23) before each use. If the seal is missing or damaged
then please contact your nearest authorised repair agent. Do
not use the appliance.
Attaching the hose (Fig. G)
u Press in the clips (24) on either side of the hose (23).
u Press the hose (23) onto the steam nozzle (4) and release
the clips (24).
Important! Ensure that the hose (23) is securely fastened
before using the hand held steam cleaner. If steam escapes
from the joint then the hose is not correctly fit, allow the unit to
cool then remove and re-fit the hose.
Attaching the variable steam jet nozzle (Fig. I)
u Press in the clips (26) on either side of the variable steam
jet nozzle (27).
u Press the variable steam jet nozzle onto the steam nozzle
(4) or the hose (23) and release the clips (26).
(Original instructions)
Important! Ensure that the variable steam jet nozzle (27) is
securely fastened before using the hand held steam cleaner.
If steam escapes from the joint then the variable steam jet
nozzle is not correctly fit, allow the unit to cool then remove
and re-fit the variable steam jet nozzle.
Attaching other accessories (Fig. H)
u Align the lugs on the hose with the recesses on the accessory.
u Press the accessory (25) onto the hose (23) and twist
anti-clockwise until the accessory clicks into place.
Note! The variable steam jet nozzle may be used without the
hose by fitting them directly to steam nozzle. All other accessories must be connected to the hose for use.
Caution! Always empty the steam mop after use.
Note: When first filled or after running dry it can take up to 45
seconds for steam to be produced.
AutoselectTM Technology (Fig. J)
This steam mop is fitted with an AutoselectTM button (6)
which shows various cleaning applications. They are used to
select the correct operating mode for your particular cleaning
operation.
Using AutoselectTM , choose from one of the following applications by pressing the autoselect button (6) until the required
setting is selected:
Wood/Laminate
Removing the hose and accessories(Fig. H & I)
Stone/Marble
Warning! The Steam nozzle, variable steam jet nozzle, hose
and accessories become hot during use. Allow the unit and all
accessories to cool before removing any accessories.
Removing an accessory (Fig. H)
u Twist the accessory (25) clockwise then pull away from
the hose (23).
Removing the hose (Fig. H)
u Press in the clips (24) on either side of the hose (23) and
pull away from the steam nozzle (4).
Removing the variable steam jet nozzle (Fig. I)
u Press in the clips (26) on either side of the variable steam
jet nozzle (27) and pull away from the steam nozzle (4).
Use
Important! This unit will kill 99.9% of bacteria & germs when
used in accordance with this manual and with the micro fibre
pad fitted and a continuous run time of 90 seconds.
Switching on and off (Steam mop)
u
To switch the appliance on, press the ON/OFF button (1).
It takes approximately 15 seconds for the steam mop to
heat up.
Note: When the steam mop is first turned on the water reservoir will glow red. Once the steam mop is ready to use the
water reservoir will glow blue.
u To switch the appliance off, press the ON/OFF button (1).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop on
the resting mat (13) with the handle (10) in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
ENGLISH
Tiles/Vinyl
The steam mop will select the correct volume of steam
required for your particular cleaning operation.
Note: Always check you are using the correct setting before
using your steam mop. For convenience the steam mop will
remember the last setting you chose.
Steam burst (Fig. J)
The steam mop is equipped with a steam burst button to aid in
the removal of stubborn marks and stains.
u During use, press the steam burst button (28) to apply
extra cleaning power.
Note: The steam burst will last for 10 seconds then the steam
mop will return to the chosen setting.
Switching on and off (Hand held steam cleaner)
(Fig. K)
u
To switch the appliance on, press the ON/OFF button (1).
It takes approximately 15 seconds for the hand held steam
cleaner to heat up.
Note: When the hand held steam cleaner is first turned on
the water reservoir will glow red. Once the hand held steam
cleaner is ready to use the water reservoir will glow blue.
u Lift the lock off switch (2) and pull the trigger switch (3).
After a few seconds steam will be produced.
u To switch the appliance off, release the trigger switch (3)
then press the ON/OFF button (1).
Caution! Always empty the hand held steam cleaner after
use.
Caution! Steam may continue to be produced for a short time
after the trigger switch (3) is released, this is normal. Switch
off and allow the unit to cool before removing any accessories.
7
ENGLISH
(Original instructions)
Hints for optimum use
General
Caution! Never use the steam mop without first attaching a
cleaning pad.
u During steam mop use you can use the cable management clip (17) to keep your cable out of the way of the
work area..
u Always vacuum or sweep the floor before using the steam
mop.
u The easiest way to use the machine is to tilt the handle to
a 45˚ angle and clean slowly, covering a small area at a
time.
u Do not use chemical cleaners with your steam mop. To
remove stubborn stains from vinyl or linoleum floors, you
can use the steam burst button to apply extra steam to
the area or pre-treat with a mild detergent and some water
before using the steam mop.
Steam cleaning with the mop
u Fit hand held steam cleaner (5) to the steam mop body
(9).
u Place a cleaning pad (12) on the floor with the ‘hook &
loop’ side facing up.
u Raise the steam mop off the resting mat (13) and lightly
press it down onto the cleaning pad (12).
u Place the steam mop on the resting mat.
u Connect the steam mop to the mains.
u Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
TM
u Press the Autoselect button (6) till the required setting is
reached.
u Pulling the handle (10) back will activate the steam pump.
After a few seconds steam will start to come out of the
steam head.
Note: When first filled or after running dry it can take up to 45
seconds for steam to be produced.
u It takes a few seconds for steam to enter the cleaning pad.
The steam mop will now glide easily over the surface to be
sanitised/cleaned.
u Push and pull the steam mop slowly across the floor to
thoroughly steam clean each section.
Note: During use you may turn off the steam pump by returning the handle to the upright position, this convenient feature
will allow you to place the steam mop on the resting mat for
a short time so that you may move items of furniture, then
continue cleaning without the need to switch the appliance off.
u When you have finished using the steam mop, return the
handle (10) to the upright position and turn it ‘OFF’, place
8
it on the resting mat (13) and wait until the steam mop
cools down. (approximately five minutes)
Caution! It is important to monitor the water level in the water
tank. To refill the water tank and continue to sanitise/clean, return the handle (10) to the upright position and turn the steam
mop ‘OFF’. Unplug the unit from the electrical wall outlet, refill
the water tank (8).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop on
the resting mat (13) with the handle (10) in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Carpet refreshing
u Place a cleaning pad (12) on the floor with the ‘hook &
loop’ side facing up.
u Raise the steam mop off the resting mat (13) and lightly
press it down onto the cleaning pad (12).
u Place the carpet glider (14) on the floor.
u Lightly press the steam mop down onto the carpet glider
(14) until it clicks into place.
u Place the steam mop on the resting mat. (13)
u Connect the steam mop to the mains.
u Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
TM
u Press the Autoselect button (6) to the Wood/Laminate
setting.
u Pulling the handle (10) back will activate the steam pump.
After a few seconds steam will start to come out of the
steam head.
Note: When first filled or after running dry it can take up to 45
seconds for steam to be produced.
u Push and pull the steam mop slowly across the carpet to
thoroughly refresh each section.
Note: During use you may turn off the steam pump by returning the handle (10) to the upright position, this convenient
feature will allow you to place the steam mop on the resting
mat (13) so that you may move items of furniture with out the
need to switch the appliance off.
u When you have finished using the steam mop, return the
handle (10) to the upright position and turn it ‘OFF’, place
it on the resting mat (13) and wait until the steam mop
cools down. (approximately five minutes)
Caution! If steam is observed escaping from the join between
the hand held steam cleaner and the steam mop body, switch
off and disconnect the unit from the mains supply. Allow to
cool. Remove the hand held steam cleaner from the steam
mop body. Inspect the seal (22) on the steam nozzle (4) and
hose (23) (fig. H). If the seal is missing or damaged then
(Original instructions)
please contact your nearest authorised repair agent. Do not
use the appliance. If the seal is in good condition re-fit the
hand held steam cleaner to the steam mop body ensuring that
it is seated firmly in place.
Caution! It is important to monitor the water level in the water
tank. To refill the water tank and continue to sanitise/clean, return the handle (10) to the upright position and turn the steam
mop ‘OFF’. Unplug the unit from the electrical wall outlet, refill
the water tank (8).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop on
the resting mat (13) with the handle (10) in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
After use (Fig. L & M)
u Return the handle (10) to the upright position and turn the
steam mop ‘OFF’,
u Place the steam mop on the resting mat (13) and wait until
the steam mop cools down. (approximately five minutes)
u Unplug the steam mop from the electrical wall outlet.
u Empty the water tank (8).
u Remove the cleaning pad (12) and wash it ready for
next use. (Take care to follow the wash care instructions
printed on the cleaning pad).
u Wrap the supply cable around the cable tidy hooks (15 &
16).
Note: The top cable tidy hook (16) rotates to easily release
the cable ready for next use.
u Clip the supply cable onto itself using the cable tidy clip
(29) close to the plug.
u Place steam mop on the resting mat (13) for storage.
Note: With the handle (10) in the upright position, the cable
neatly wrapped around the cable tidy hooks (15 & 16) and
secured with the cable tidy clip (29) your steam mop will stand
on its own for storage. Alternatively there is a hanging bracket
(30) built into the hand grip (31) which will allow your steam
mop to be hung from a suitable hook on the wall. Always
ensure that your wall hook is capable of supporting the weight
of the steam mop safely.
Hand held steam cleaning
u Attach the required accessory.
u Connect the hand held steam cleaner to the mains.
u Press the ON/OFF button (1). It takes approximately 15
seconds for the hand held steam cleaner to heat up.
u Lift the lock off (2) and pull the trigger switch (3) to activate
the steam pump. After a few seconds steam will start to
come out of the accessory.
Note: When first filled or after running dry it can take up to 45
ENGLISH
seconds for steam to be produced.
Note: During use you may turn off the steam pump by releasing the trigger switch, this convenient feature will allow you to
place the hand held steam cleaner down for a short time so
that you may move items of furniture, then continue cleaning
without the need to switch the appliance off.
u When you have finished using the hand held steam
cleaner, release the trigger switch (3), turn it ‘OFF’ and
disconnect from the mains supply. Wait until the steam
mop cools down before storing. (approximately five
minutes)
Caution! It is important to monitor the water level in the water
tank. To refill the water tank and continue to sanitise/clean,
turn the hand held steam cleaner ‘OFF’. Unplug the unit from
the electrical wall outlet, refill the water tank (8).
Caution! Steam may continue to be produced for a short time
after the trigger switch (3) is released, this is normal. Switch
off and allow the unit to cool before removing any accessories.
Technical data
FSMH1621
(Type 1)
Voltage
Vac
Power
W
Tank capacity
ml
Weight
kg
230
1600
350
3.6
Troubleshooting
If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local Black & Decker repair agent.
Problem
Step
Possible solutions
The steam mop is
1
Check the unit is plugged in at the wall
socket.
not turning on.
2
Check the unit is switched on using the on/
off switch (1).
The digital controls
3
Check the fuse in the plug.
4
Check that the handle (10) of the steam mop
is pushed firmly into the steam mop body (9).
do not light up.
Check that the arrow on the handle is flush
with the top of the steam mop body (9).
5
Check that the hand held steam cleaner (5)
is firmly docked into the steam mop body (9).
6
Check steps 1, then 2, then 3.
9
(Original instructions)
ENGLISH
Problem
The steam mop is
Step
Possible solutions
Problem
Step
Possible solutions
7
The steam mop will only produce steam
Steam is escaping
22
Refer to the assembly chapter of the manual
not producing
once the handle is pulled back from the
steam.
upright position.
8
Check that the water tank (8) is full.
NOTE: When first filled or after running dry it
can take up to 45 seconds for steam to be
produced.
9
Check that the Steam head (11) is firmly
docked into the steam mop body (9).
The digital controls
10
Check steps 5, then 1, then 2, then 3.
11
Check steps 4, then 5, then 1, then 2, then 3
12
Check steps 7, then 8, then 9, then 5, then 3.
13
The steam mop has 3 settings. Press the
go out during use.
The steam mop
stops producing
steam during use.
The steam mop is
autoselect button (6) to reduce the amount of
producing too
steam being produced.
much steam during
use.
14
Check that the steam burst button (28) has
15
The steam mop has 3 settings. Press the
not been pressed.
The steam mop is
producing too little
autoselect button (6) to increase the amount
steam during use.
of steam being produced.
16
Press the steam burst button (28) to
17
The hand held steam cleaner has a lock off
temporarily increase the amount of steam.
No steam is being
produced from the
feature. Lift the lock off switch (2) and pull
hand held steam
the trigger switch (3). After a few seconds
steam will be produced.
cleaner when the
trigger is pulled.
18
Check steps 8, then 1, then 2, then 3.
The hand held
19
The hand held steam cleaner will begin to
steam cleaner is
produce steam after 15 seconds and will
producing too little
reach maximum steam flow after 45
seconds.
steam during use.
The hand held
20
Firmly press the hand held steam cleaner
steam cleaner will
release button (20) down, then pull the hand
not come out from
held steam (5) cleaner from the steam mop
the steam mop
body (9).
body.
The accessories
21
Refer to the assembly chapter of the manual
keep falling off the
for correct fitting instructions of all parts and
unit.
accessories.
10
for correct fitting instructions of all parts and
from unexpected
accessories.
areas of the unit.
Where can I get
further information
/ accessories for
my steam mop.
23
www.blackanddecker.co.uk/steammop
www.blackanddecker.ie/steammop
TYPE
FSMH1621
1
3
1
20
22
2
4
21
5
6
25
8
18
7
12
11
15
10
14
9
17
16
E16763
www.2helpU.com
01 - 10 - 12
TYPE
FSMH1621 - Accessories
1
1
3
2
5
4
6
E16765
www.2helpU.com
02 - 10 - 12
13
14
ENGLISH
Do not forget to register your product!
www.blackanddecker.co.uk/productregistration
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product
code to Black & Decker in your country.
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark, Victoria, 3138
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Auckland 1060
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
90598593 REV-0
Tel. 03-8720 5100
Fax 03-9727 5940
Tel. +64 9 259 1133
Fax +64 9 259 1122
Tel. 01753 511234
Fax 01753 551155
05/2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising