Crestron | FT-PWR | Installation guide | Crestron FT-PWR Installation guide

Crestron FT-PWR Installation guide
Crestron FT-PWR-D-B &
FT-PWR-D-BALUM
FlipTop Power Center with Dual AC
Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2008 Crestron Electronics, Inc.
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
FlipTop Power Center
Contents
FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM
1
Introduction ............................................................................................................................... 1
Features and Functions ................................................................................................ 1
Specifications .............................................................................................................. 2
Physical Description.................................................................................................... 2
Industry Compliance ................................................................................................... 6
Setup .......................................................................................................................................... 7
Installation ................................................................................................................... 7
Hardware Hookup ..................................................................................................... 11
Operation ................................................................................................................................. 12
Problem Solving ...................................................................................................................... 13
Troubleshooting......................................................................................................... 13
Further Inquiries ........................................................................................................ 13
Future Updates .......................................................................................................... 13
Return and Warranty Policies .................................................................................................. 14
Merchandise Returns / Repair Service ...................................................................... 14
CRESTRON Limited Warranty................................................................................. 14
Operations Guide – DOC. 6640A
Contents • i
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
FlipTop Power Center
FlipTop Power Center:
FT-PWR-D-B & FT-PWR-D-BALUM
Introduction
Features and Functions
The FT-PWR-D-B and FT-PWR-D-BALUM provide an elegant connectivity
solution in a stylish flush mount tabletop package. Beneath the "FlipTop" lid, the
cable storage compartment keeps installed interface cables (not included) at the
ready for plugging in computers, AV sources, communication, control, or data cable.
When not in use, the user end of each cable stows neatly within the FlipTop
compartment while excess cable simply drops out-of-sight below the box.
•
•
•
•
•
*
Stylish, flush mount in tabletop surface
Easy pullout universal cable management
Eight, grommeted holes for smooth passage of virtually any type of
AV, communication, control or data cables
Two AC power receptacles in FlipTop compartment
Available in black anodized (FT-PWR-D-B) or brushed aluminum
(FT-PWR-D-BALUM)*
For simplicity within this guide, the finish designation is omitted and FT-PWR-D is used, except
where noted.
FlipTop Housing
Handsomely finished in either black anodized or brushed aluminum, the FT-PWR-D
mounts flush in any tabletop surface for a clean, discreet appearance.
Cable Storage Compartment
The FT-PWR-D also provides for extensive connectivity through an easy pull out
cable storage mechanism to support a wide range of applications and signal types.
Eight grommeted holes are provided in the bottom plate, allowing for smooth pass
through of virtually any type of AV, communication, control or data cable (cables
not included). When not in use, the user end of each cable stows neatly within the
FlipTop compartment while excess cable simply drops out of sight below the box.
Operations Guide – DOC. 6640A
FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM • 1
FlipTop Power Center
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
AC Power Outlets
For complete connectivity, two AC power receptacles are included within the
FlipTop compartment.
Specifications
Specifications for the FT-PWR-D are listed in the following table.
FT-PWR-D Specifications
SPECIFICATION
DETAILS
Environmental
Temperature
41° to 104°F (5° to 40°C)
Humidity
10% to 90% RH (non-condensing)
Enclosure
Dimensions
Black painted metal with black anodized or
brushed aluminum cover; flush tabletop
mountable
Height: 5.39 in (13.69 cm) with lid closed
Width: 6.75 in (17.15 cm)
Depth: 5.71 in (14.50 cm)
Weight
3.75 lbs (1.7 kg)
Physical Description
This section provides information on the connections, controls, and indicators
available on your FT-PWR-D.
FT-PWR-D Physical View
NOTE: Cables not included.
2 • FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM
Operations Guide – DOC. 6640A
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
FlipTop Power Center
FT-PWR-D Overall Dimensions – Top View
5.08 in
(12.90 cm)
5.71 in
(14.50 cm)
6.75 in
(17.15 cm)
FT-PWR-D Overall Dimensions (Front View)
FT-PWR-D Overall Dimensions (Bottom View)
5.16 in
(13.10 cm)
6.25 in
(15.88 cm)
Operations Guide – DOC. 6640A
FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM • 3
FlipTop Power Center
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
FT-PWR-D Overall Dimensions (Rear View)
FT-PWR-D Overall Dimensions (Side View)
2.31 in
(5.88 cm)
4.31 in
(10.95 cm)
5.39 in
(13.69 cm)
4.63 in
(11.76 cm)
5.21 in
(13.23 cm)
FT-PWR Front Face View
1
4 • FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM
Operations Guide – DOC. 6640A
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
FlipTop Power Center
FT-PWR-D Bottom View
2
Connectors, Controls, & Indicators
#
1
2
Operations Guide – DOC. 6640A
CONNECTORS,
CONTROLS, &
INDICATORS
DESCRIPTION
(2) Grounded AC sockets, AC power pass
through outlets;
Maximum load: 10 Amps @ 120 Volts AC,
50/60 Hz
(1) 9 foot grounded AC line cord; passes
through to front panel AC power outlets.
FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM • 5
FlipTop Power Center
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
Industry Compliance
As of the date of manufacture, the FT-PWR-D has been tested and found to comply
with specifications for CE marking and standards per EMC and
Radiocommunications Compliance Labelling.
NOTE: This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
6 • FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM
Operations Guide – DOC. 6640A
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
FlipTop Power Center
Setup
Installation
NOTE: To prevent overheating, do not operate this product in an area that exceeds
the environmental temperature range listed in the specifications table. Consideration
must be given if installed inside a closed desk or in a closed podium since the
operating ambient temperature of these environments may be greater than the room
ambient. Contact with thermal insulating materials should be avoided on all sides of
the unit.
There are two steps to installing the FT-PWR-D.
Tools required
Cable Management Kit
•
Phillips screwdriver
•
Appropriate carpentry tools for cutout
The FT-PWR-D is shipped with a separate cable management kit for organizing
cables fed into the power center.
Parts Supplied for Cable Management Kit
DESCRIPTION
PART NUMBER
QUANTITY
Cable Support Plate
2011563
1
Bushing 0.55 inch (1.40cm) ID,
0.80 inch (2.03 cm) OD
2010496
2
Bushing 0.39 inch (0.99 cm) ID,
0.64 inch (1.63 cm) OD
2011070
2
Bushing 0.31 inch (0.79 cm) ID,
0.50 inch (1.27 cm) OD
2009522
4
Screw 04-40, 0.25 inch (0.64 cm) L
2007158
4
The cable support plate should be installed before mounting the FT-PWR-D to a
surface. The cables are threaded through the cable support plate.
Operations Guide – DOC. 6640A
1.
Place bushings on the cables you wish to install in the power center (eight
bushings supplied). Use bushings appropriate to the diameter of each cable.
2.
Thread the cables through the cable support plate slots appropriate to the
size of the cable and the bushing you attached in the previous step.
3.
Snap the bushings into the slots on the cable support plate.
4.
Feed all excess cable through the opening.
5.
Attach the cable support plate using the four 4-40 x ¼ LG screws.
6.
If desired, any installed cables can be secured to the bottom bar with tie
wraps (not supplied).
FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM • 7
FlipTop Power Center
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
Cable Support Plate Installation
When selecting cables for installation in the FT-PWR-D, cable connector length and
strain relief diameter are important considerations.
•
If the connector is too long, it can interfere with cover operation.
•
If the width of the cable strain relief is too similar to the bushing inside
diameter, the bushing can trap the cable.
NOTE: Do not use the cable support plate without the bushings.
Example Cable End
Must be wider than the inside diameter of the bushing
Large Bushing: 0.54 in (1.37 cm)
Medium Bushing: 0.39 in (0.99 cm)
Small Bushing: 0.31 in (0.79 cm)
Must not be longer than 2.13 in
(5.4cm) to avoid interference
with cover operation
8 • FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM
Operations Guide – DOC. 6640A
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
FlipTop Power Center
Cables Threaded Through the Cable Plate
NOTE: Ensure that any cables you install have sufficient clearance to enable smooth
movement. Allow approximately 40 inches (102 cm) from the top surface of the
FlipTop box.
Mounting to Surface
The FT-PWR-D is designed to mount in a horizontal surface, such as a desk top,
lectern, or podium. The following diagram illustrates the required opening size to
accommodate the FT-PWR-D. Use the supplied template (4010018) to make the
cutout.
Cutout Dimensions for FT-PWR-D
6 3/8 in
(162 mm)
5 5/16 in
(135 mm)
Maximum
Radius
1/8 in
(4 mm)
NOTE: Be sure to feed the attached power cord and all required cables through the
mounting hole before inserting the FT-PWR-D.
Operations Guide – DOC. 6640A
FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM • 9
FlipTop Power Center
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
Mounting Parts Supplied
DESCRIPTION
Screw #6-32, 3/16” L, Pan Head, Phillips
PART
NUMBER
QUANTITY
2007204
8
Screw #10-32, 2” L, Pan Head, Phillips
2007293
4
Mounting Bracket
2013224
2
1.
Install the eight supplied #6-32 screws, but do not tighten (four on the front
side and four on the rear side). These will be used to secure the front and
rear mounting brackets.
2.
Position the FT-PWR-D in the mounting hole.
Mounting Bracket Screw Locations
#6-32 Screws
#6-32 Screws
Surface
Cutout
3.
Thread a small portion of the two-inch long #10-32 screws into the
mounting brackets (two screws per bracket). Refer to the following
diagram.
4.
Slide the mounting brackets over the #6-32 screws and tighten the
#6-32 screws.
10 • FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM
Operations Guide – DOC. 6640A
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
FlipTop Power Center
Mounting Bracket Installation
5.
Turn the four #10 screws equally until they contact the underside of the
mounting surface enough to secure the unit. DO NOT OVER TIGHTEN.
CAUTION: Do not over-tighten the #10 screws as this may damage the surface
and/or the unit.
Mounting Brackets Installed
7.21 in
(18.31 cm)
FOUR #10-32 2" L
SCREWS
EIGHT #6-32 3/16" L
SCREWS
TWO MOUNTING BRACKETS
Hardware Hookup
Hookup consists of simply plugging the line cord into an appropriate outlet.
NOTE: The maximum continuous current from equipment under any external load
conditions shall not exceed a current limit that is suitable for the minimum wire
gauge used in interconnecting cables. The ratings on the connecting unit's supply
input should be considered to prevent overloading the wiring.
Operations Guide – DOC. 6640A
FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM • 11
FlipTop Power Center
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
Operation
The spring-loaded lid is opened by pressing briefly and releasing it. Cables are stored
neatly beneath the lid when not in use to keep out debris and dust. The lid opens 135
degrees, allowing full access to cables and power inside.
Beneath the lid, a recessed compartment with eight grommeted holes through the
bottom plate allows any type of AV, communication, data or control cables to be
instantly available for connection to your devices. The recessed compartment also
contains two three-pronged, grounded AC sockets.
12 • FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM
Operations Guide – DOC. 6640A
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
FlipTop Power Center
Problem Solving
Troubleshooting
The following table provides corrective action for possible trouble situations. If
further assistance is required, please contact a Crestron customer service
representative.
FT-PWR-D Troubleshooting
TROUBLE
POSSIBLE CAUSE(S)
Device connected
to the AC socket
is not working.
Lack of, or insufficient
power to, AC socket.
CORRECTIVE ACTION
Provide appropriate power to
the line cord.
Further Inquiries
If you cannot locate specific information or have questions after reviewing this
guide, please take advantage of Crestron's award winning customer service team by
calling Crestron at 1-888-CRESTRON [1-888-273-7876].
You can also log onto the online help section of the Crestron website
(www.crestron.com/onlinehelp) to ask questions about Crestron products. First-time
users will need to establish a user account to fully benefit from all available features.
Future Updates
As Crestron improves functions, adds new features, and extends the capabilities of
the FT-PWR-D, additional information may be made available as manual updates.
These updates are solely electronic and serve as intermediary supplements prior to
the release of a complete technical documentation revision.
Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
Operations Guide – DOC. 6640A
FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM • 13
FlipTop Power Center
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
Return and Warranty Policies
Merchandise Returns / Repair Service
1.
No merchandise may be returned for credit, exchange, or service without prior authorization
from CRESTRON. To obtain warranty service for CRESTRON products, contact an
authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory
and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying
the nature of the problem, name and phone number of contact person, RMA number, and
return address.
2.
Products may be returned for credit, exchange, or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped freight
prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with
RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect
or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its
sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any
products returned with an RMA.
3.
Return freight charges following repair of items under warranty shall be paid by CRESTRON,
shipping by standard ground carrier. In the event repairs are found to be non-warranty, return
freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in materials
and workmanship under normal use for a period of three (3) years from the date of purchase from
CRESTRON, with the following exceptions: disk drives and any other moving or rotating mechanical
parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen display and
overlay components are covered for 90 days; batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON
dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if
any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended, or if it has been subjected to misuse, accidental
damage, modification, or improper installation procedures. Furthermore, this warranty does not cover any
product that has had the serial number altered, defaced, or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages
inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for any claim made by a
third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or
labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the
unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or
implied, nor authorizes any other party to offer any warranty, including any implied warranties of
merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are
limited to the terms of this limited warranty. This warranty statement supersedes all previous warranties.
Trademark Information
All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered trademark
of Microsoft Corporation. Windows95/98/Me/XP/Vista and WindowsNT/2000 are trademarks of Microsoft Corporation.
14 • FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM
Operations Guide – DOC. 6640A
Crestron FT-PWR-D-B & FT-PWR-D-BALUM
FlipTop Power Center
This page is intentionally left blank.
Operations Guide – DOC. 6640A
FlipTop Power Center: FT-PWR-D-B & FT-PWR-D-BALUM • 15
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Operations & Installation Guide – DOC. 6640A
(2019709)
03.08
Specifications subject to
change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising