WV-CS950_manual_eng
WV-CS950/954E Cover(1-4) 05.2.15 5:58 PM ページ 366
Colour CCTV Camera
Operating Instructions
Model Nos.
Printed in Japan
Gedruckt in Japan
Imprimé au Japon
Impreso en Japón
Stampato in Giappone
© 2004 Matsushita Electric Industrial Co., Ltd. All rights reserved.
AM0105-0 3TR003398AAA
WV-CS950
WV-CS954E
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
WV-CS950 05.2.14 8:37 PM ページ2
We declare under our sole responsibility that the product to
which this declaration relates is in conformity with the standards or other normative documents following the provisions of
Directives EEC/73/23 and EEC/89/336.
Vi deklarerar härmed värt fulla ansvar för att den produkt till
vilken denna deklaration hänvisar är i överensstämmelse med
standarddokument, eller andra normativa dokument som
framställs i EEC-direktiv nr. 73/23 och 89/336.
Wij verklaren als enige aansprakelijke, dat het product waarop
deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatieve documenten, overeenkomstig de
bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC.
Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä
ilmoitus koskee, noudattaa seuraavia standardeja tai muita
ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC
ja 89/336/EE. säädöksiä.
Vi erklærer os eneansvarlige for, at dette produkt, som denne
deklaration omhandler, er i overensstemmelse med standarder
eller andre normative dokumenter i følge bestemmelserne i
direktivene 73/23/EEC og 89/336/EEC.
Vi erklærer oss alene ansvarlige for at produktet som denne
erklæringen gjelder for, er i overensstemmelse med følgende
normer eller andre normgivende dokumenter som følger
bestemmelsene i direktivene 73/23/EEC og 89/336/EEC.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT
CAREFULLY.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
WARNING
DO NOT REMOVE COVER (OR BACK).
THIS APPARATUS MUST BE EARTHED
IMPORTANT
NO USER-SERVICEABLE PARTS INSIDE.
The wires in this mains lead are coloured in accordance with the following code.
Green-and-yellow:
Earth
Blue:
Neutral
Brown:
Live
As the colours of the wire in the mains lead of this appliance
may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter E or by
the earth symbol 1 or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal in the plug which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal in the plug which is marked with the letter L or coloured red.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
The serial number of this product may be found on the
top of the unit.
You should note the serial number of this unit in the
space provided and retain this book as a permanent
record of your purchase to aid identification in the event
of theft.
Turn the power off at the mains to
disconnect the main power for all
unit.
Model No.
WV-CS950, CS954E
Serial No.
WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
CAUTION: An ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorporated
in the electrical installation of the building.
-2-
WV-CS950 05.2.15 6:11 PM ページ3
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not use near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or
the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the
points where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-overs.
S3125A
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
-3-
WV-CS950 05.2.14 8:37 PM ページ4
LIMITATION OF LIABILITY
THIS PUBLICATION COULD INCLUDE TECHNICAL
INACCURACIES OR TYPOGRAPHICAL ERRORS.
CHANGES ARE ADDED TO THE INFORMATION
HEREIN, AT ANY TIME, FOR THE IMPROVEMENTS OF
THIS PUBLICATION AND/OR THE CORRESPONDING
PRODUCT(S).
THIS PUBLICATION IS PROVIDED “AS IS” WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR ANY PARTICULAR PURPOSE, OR NONINFRINGEMENT OF THE THIRD PARTY'S RIGHT.
DISCLAIMER OF WARRANTY
IN NO EVENT SHALL MATSUSHITA ELECTRIC
INDUSTRIAL CO., LTD. BE LIABLE TO ANY PARTY OR
ANY PERSON, EXCEPT FOR REPLACEMENT OR
REASONABLE MAINTENANCE OF THE PRODUCT,
FOR THE CASES, INCLUDING BUT NOT LIMITED TO
BELOW:
(4) INCONVENIENCE OR ANY LOSS ARISING
WHEN IMAGES ARE NOT DISPLAYED, DUE TO
ANY REASON OR CAUSE INCLUDING ANY
FAILURE OR PROBLEM OF THE PRODUCT;
(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING OUT
OF THE SYSTEM COMBINED BY THE DEVICES
OF THIRD PARTY.
(6) ANY CLAIM OR ACTION FOR DAMAGES,
BROUGHT BY ANY PERSON OR ORGANIZATION BEING PHOTOGENIC SUBJECT, DUE TO
VIOLATION OF PRIVACY WITH THE RESULT OF
THAT SURVEILLANCE-CAMERA's PICTURE,
INCLUDING SAVED DATA, FOR SOME REASON, BECOMES PUBLIC OR IS USED FOR THE
PURPOSE OTHER THAN SURVEILLANCE.
(7) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, ANY LOSS OR DAMAGE, ARISING
OUT OF THE IMPROPER DETECTION OR SLIPUP IN DETECTION BY VMD (Video Motion
Detector) FUNCTION OF THE PRODUCT.
(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR EXEMPLARY,
ARISING OUT OF OR RELATING TO THE
PRODUCT;
(2) PERSONAL INJURY OR ANY DAMAGE
CAUSED BY INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER;
(3) UNAUTHORIZED DISASSEMBLE, REPAIR OR
MODIFICATION OF THE PRODUCT BY THE
USER;
-4-
WV-CS950 05.2.14 8:37 PM ページ5
FEATURES
■ Privacy Zone Function
This Colour CCTV Camera is a video surveillance
device that incorporates a 1/4-type {1/4"} CCD, a 30x
zoom lens, preset and pan and tilt capabilities in a
dome configuration. It also has the following features.
The privacy zone function makes it possible to mask
specific areas of the scene from view.
■ Patrol Function
■ Super Dynamic 3 (SUPER-D 3)
The patrol function remembers manual camera
movement routines for automatic playback when they
are needed. For example, you can teach the camera
the movements of the people you want to monitor, by
replaying the stored parameters complicated
movements are done automatically.
SUPER-D 3 makes it possible to capture clear images
of subjects whose illumination is extremely different.
■ New DSP for High Sensitivity
A new noise reduction system lowers minimum
illuminance to 0.5 lux in the colour mode and 0.04 lux
in the black and white mode.
■ Camera Position Memory
■ Auto Night time Switching to Black
and White Mode
The system can be configured with up to 256 camera
positions. A particular camera position can be selected
and viewed by entering the applicable preset number
on the system controller 10-key pad.
The camera can be configured to switch to the black
and white mode automatically under low light
conditions for clear images, even at night.
■ Motion Detection
■ Digital Flip
The system can be configured so any motion on the
monitor screen during surveillance causes output of an
alarm signal.
This function can be used to structure a system with a
VCR that records images of night time intruders.
Normally, a camera needs to stop when it points
straight down during a tilt operation. With digital flip,
however, the camera is able to tilt from 0° to 180° in a
single motion. This makes it possible to track subjects
passing directly under the camera more smoothly.
Digital Flip Operation
Tilting
downwards
The picture is flipped
when the camera is
pointing straight down
(at around 135°).
Tilting upwards.
· · · Digital flip is performed only when the system controller joystick is held downwards.
ACCESSORIES
Operating Instructions (this manual) . . . . . . . . . .1 pc.
Warranty Certificate . . . . . . . . . . . . . . . . . . . . . . .1 pc.
The following items are for installation.
Decorative Cover . . . . . . . . . . . . . . . . . . . . . . . . .1 pc.
Dust Protection Sheet . . . . . . . . . . . . . . . . . . . . . .1 pc.
8P Alarm Cable . . . . . . . . . . . . . . . . . . . . . . . . . . .1 pc.
4P Alarm Cable . . . . . . . . . . . . . . . . . . . . . . . . . . .1 pc.
Connector for 24 V AC (only for WV-CS954E) . . .1 pc.
OPTIONAL ACCESSORIES
Dome Cover(approx.50 % transparency,smoked type) . . . . . . .WV-CS3SE
Ceiling Mount Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .WV-Q105E/WV-Q116E/WV-Q117E
Wall Mount Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .WV-Q118E
-5-
WV-CS950 05.2.14 8:37 PM ページ6
PRECAUTIONS
8. Do not operate the camera beyond the specified
temperature, humidity or power source ratings.
Do not use the camera in an extreme environment
where high temperature or high humidity exists. Do
not place the camera near heat sources such as
radiators, stoves or other units that produce heat.
Use the camera under conditions where
temperature is between –10 °C - +50 °C, preferably
+40 °C and humidity is below 90 %.
The input power source is 220 V - 240 V AC for WVCS950 and 24 V AC for WV-CS954E.
1. Do not attempt to disassemble the camera.
To prevent electric shock, do not remove screws or
covers.
There are no user-serviceable parts inside.
Ask qualified service personnel for servicing.
2. Handle the camera with care.
Do not misuse the camera. Avoid striking, shaking,
etc. The camera could be damaged by improper
handling or storage.
3. Do not expose the camera to rain or moisture,
nor try to operate it in wet areas.
This product is designed for indoor use or locations
where it is protected from rain and moisture.
Turn the power off immediately and ask qualified
service personnel for servicing.
Moisture can damage the camera and also create
the danger of electric shock.
9. Do not install the camera near the air outlet of an
air conditioner.
The lens may become cloudy due to condensation
if the camera is used under the following
conditions.
• Rapid temperature fluctuations by switching the air
conditioner on and off.
• Rapid temperature fluctuations due to frequent door
opening and closing.
• Use in an environment where eyeglasses become
foggy.
• Use in a room filled with cigarette smoke or dust.
If the lens becomes cloudy due to condensation,
remove the dome cover and wipe all moist surfaces
with a soft cloth.
4. Do not use strong or abrasive detergents when
cleaning the camera body.
Use a dry cloth to clean the camera when it is dirty.
When the dirt is hard to remove, use a mild
detergent and wipe gently. Care should be taken
not to scratch the dome cover when wiping it.
Afterwards, wipe off the remaining detergent with a
dry cloth.
5. Never aim the camera at the sun.
Whether or not the camera is in use, never aim it at
the sun or other extremely bright objects.
Otherwise, blooming or smear may be caused.
10. Consumables
Parts having contacts such as the lens-drive
motors, cooling fan motor and slip-rings inside the
camera are subject to wear with time. Please ask
the nearest service centre about replacement and
maintenance of such parts.
6. Never aim the camera at strong light sources for
an extended period of time.
A light source such as a spot light causes burn-in
on the display screen. Failure to observe this may
cause the image to become discoloured due to
deterioration of the colour filter in the CCD.
11. Do not aim the camera at the same object for a
long time.
Burn-in of an image may be caused on the
fluorescent screen of CRT.
12. Self-diagnosis Function
If the camera continues operating abnormally for 30
seconds or more due to such an accident as
external noise, the camera will automatically reset
its power. In the case it happens frequently, check
if there would be any environmental cause.
* Matsushita Electric Industrial Co., Ltd. herewith
declares that it will not be liable for any damage,
whether direct or indirect, caused by using the
product for business transaction or security, or
malfunctioning of this product.
7. Do not install this camera upside down.
This camera is designed for mounting on the ceiling
or wall. Using this camera installed upside down,
for example, mounted on the floor, may cause
malfunction.
-6-
WV-CS950 05.2.14 8:37 PM ページ7
OPERATING PRECAUTIONS
■ The camera does not have a power switch
■ Do not point the camera at a strong light source.
Power turns on as soon as the power cord is plugged
into a power outlet. Before cleaning the camera,
unplug the power cord from the power outlet.
Intense light such as that produced by a spotlight
concentrated on one part of the screen can cause
blooming (rainbow around the strong light) or smearing
(vertical stripes above and below the strong light).
■ What to do if OVER HEAT appears on the display
This message indicates that the interior of the camera
has become very hot. Immediately unplug the power
cord from the power outlet, and contact a qualified
service person or system installer.
Bright Subject
■ Note the following to ensure long-term troublefree operation
Smearing
Long operation under high temperatures and high
humidity can cause components to deteriorate and
shorten camera life.
The recommended ambient operation temperature is
less than +35 °C.
Make sure the camera is installed in a location where it
is not directly exposed to heat from a radiator, heater,
etc.
Blooming
■ Do not aim the camera at the same object for a
long time.
Burn-in of an image may be caused on the fluorescent
screen of CRT.
■ Handle the camera carefully.
Do not drop the camera, or subject it to strong impact
or vibration. Such conditions create the risk of
malfunction.
■ Avoid use of this camera in a food preparation
area and other locations where there are large
amounts of steam vapour and oil.
■ Do not allow the camera to become wet.
■ About the Camera Cleaning Function
Make sure that it is not exposed directly to water. Such
conditions create the risk of malfunction.
Prolonged use can lead to noise on the monitor and
divergence of preset positions.
If such conditions persist even after you perform
camera cleaning (page 35), use the special setup
menu to execute the “REFRESH” operation (page 39).
If you are using a matrix switcher with a camera
cleaning function (WJ-SX550C), configure the matrix
switcher Auto Cleaning settings so cleaning is
performed once a day.
■ Condensation inside of the dome cover
Remove the dome cover and use a soft cloth to wipe
off the moisture.
■ Consumables
Parts having contacts such as the lens-drive motors,
cooling fan motor and slip-rings inside the camera are
subject to wear with time. Please ask the nearest
service centre about replacement and maintenance of
such parts.
■ This camera is designed for use in a hanging
configuration only.
■ Cleaning the camera
Do not use it in an upright configuration on a tabletop,
floor, etc. Such conditions create the risk of
malfunction.
Turn off the camera and wipe it with a soft cloth. If the
camera is very dirty, wipe it off gently with a soft cloth
moistened with a weak solution of water and a neutral
kitchen detergent. Wring all excess liquid from the
cloth before wiping the camera. Next, wipe off all
remaining solution with a soft, dry cloth.
A dirty dome cover or lens causes deterioration of
picture quality. Use lens cleaning paper (like the type
available for cleaning eyeglasses or a camera lens) to
clean the lens.
The dome cover is particularly susceptible to damage.
Gently wipe it with a soft cloth.
■ CCD colour filter burn-in
Intense light concentrated on one spot for a long
period can cause deterioration of the CCD internal
colour filters, and discoloration of the affected part.
Even if the camera position is changed from a fixed
position, the discoloration at the previous location of
the concentrated light will remain on the screen.
-7-
WV-CS950 05.2.14 8:37 PM ページ8
■ Downloading (saving) or uploading (recovering)
camera setting information
Camera setting information that can be downloaded to
the system controller etc, includes existing preset
position settings and menu settings. However, the
following items are not included.
• Patrol function (page 32)
• Area title function (page 34)
• Blemish compensation pattern (page 39)
• RS485 settings (page 20)
• Password settings (page 42)
Make sure that the functions listed below are all turned
off before downloading camera preset data to the
system controller etc. or uploading downloaded data to
the camera. Download or upload will not end normally
if it is performed while any of these functions are turned
on.
• Alarm (page 37)
• Preset Alarm (page 37)
• Cleaning (page 35)
• Motion Detection (page 36)
• Auto Mode (page 30)
• Self Return (page 30)
When downloading or uploading preset data, aim the
camera at a wall or similar object so there is as little
movement as possible on the screen.
Uploading of WV-CS950 series preset data to other
models (e.g. WV-CS850 series, WV-CS850A series,
WV-CS850B series and WV-NS320 series) may cause
an error and failure of the uploading process.
■ Self-diagnosing Function
If abnormal operation due to external noise or some
other reason continues for more than 30 seconds, the
camera will automatically reset itself and restore
normal operation. Reset operation the same
initialisation routine that is performed when the camera
is turned on. If the reset is required too often, it could
mean that the camera is installed in a location where
there is a large amount of external noise. This can
cause malfunction of the camera, so you should
contact a qualified service person or system installer
as soon as possible.
-8-
WV-CS950 05.2.14 8:37 PM ページ9
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
LIMITATION OF LIABILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
DISCLAIMER OF WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
■ Super Dynamic 3 (SUPER-D 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
■ New DSP for High Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
■ Auto Nighttime Switching to Black and White Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
■ Digital Flip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
■ Privacy Zone Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
■ Patrol Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
■ Camera Position Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
■ Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ACCESORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
OPTIONAL ACCESORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
CONSTRUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
INSTALLATION PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
DIP SWITCH SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
■ Communication Parameters (DIP Switch 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
■ Unit Number (DIP Switch 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
■ RS485 Communication Parameters (DIP Switch 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
CAMERA INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
■ Preparing the Camera and Decorative Cover for Side Cable Exit . . . . . . . . . . . . . . . . .15
■ Installing the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
UNINSTALLING THE CAMERA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
■ Removing the Decorative Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
■ Uninstalling the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
RS485 SET-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
USING THE SET-UP MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
■ Displaying the Set-up Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
■ Language Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
CAMERA SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
■ Using the Camera Set-up Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
PAN / TILT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
■ Using the Pan/Tilt Set-up Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
ALARM SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
■ Using the Alarm Set-up Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
SPECIAL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
■ Using the Special Set-up Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
SCENE SELECT SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
■ Using the Scene Select Setting Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
QUICK MENU SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
■ Displaying the Quick Set-up Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
PASSWORD SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
■ Password Lock Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
SHORTCUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
-9-
WV-CS950 05.2.14 8:37 PM ページ10
CONSTRUCTION
Alarm Input Connector
Alarm Output Connector
Camera Mounting Base
Video Output Connector
Data Port
Power Connector for WV-CS954E
Power Connector for WV-CS950
Safety Wire
Decorative Cover (provided)
Dome Anchor Ring
Dome Cover
Rotate the dome anchor ring to the left to remove it.
The dome cover is easily damaged,
and should be handled with care.
Lens
The lens cannot be replaced.
Ensuring Trouble-free Operation
• This camera uses a “slip ring” for transmission of electrical power and signals. A dirty slip ring can cause
deterioration of picture quality during panning and generation of noise.
In order to ensure trouble-free camera operation, make sure that the cleaning function (page 35) is turned on.
• If cleaning the slip ring does not eliminate poor picture quality and noise, it could mean that the slip ring has
reached the end of its service life. Contact a qualified service person or system installer to have it replaced.
-10-
WV-CS950 05.2.14 8:37 PM ページ11
INSTALLATION PRECAUTIONS
use in a vehicle.)
• Near an air conditioner outlet, near a door that opens
up to the outdoors, or any other area subjected to
temperature extremes (Such conditions can cause
clouding and condensation formation on the dome
cover.)
Warning: Discuss the installation location for the
camera with your retailer, and select a place that is
strong enough for the installation. If you install the
camera on a ceiling or wall, except for accidents
caused by fault in the camera, Panasonic holds
absolutely no responsibility for accidents caused by
the camera falling due to unsuitable installation.
Take sufficient care when installing the camera. If
the installation is not strong enough, be sure to
sufficiently reinforce the location and check that it is
safe.
Warning: Always request installation work from a
qualified service person or system installer. Lack of
technical knowledge creates the risk of fire, electric
shock, personal injury, and material damage.
■ Wiring the Camera
• If you need to connect a ground, be sure to do it before
you connect the main power plug. Also, when
removing the ground, be sure to disconnect the main
power plug.
• The camera does not have a power switch, so it turns on
as soon as the power cord is plugged into a power outlet.
During the electrical work, configure the power supply to
the camera so it can be turned on and off. A self-cleaning
function is activated (PAN/TILT/ZOOM/FOCUS) when the
camera is turned on.
■ Camera Installation Location
• Install the camera on a ceiling (concrete, etc.) at a
location that is sufficiently strong to support it.
• When installing the camera on a ceiling of
insufficient strength (like a drop ceiling), use the
optionally available WV-Q105E Direct Attachment
Ceiling Mounting Bracket or the WV-Q116E
Embedded Ceiling Mount Bracket.
• For ceiling mounting, use the optionally available
WV-Q117E Ceiling Mount Bracket.
• For wall mounting, use the optionally available WVQ118E Wall Mount Bracket.
■ When wiring the camera, its cables (power, video
output, RS485, alarm in, alarm out) can exit out
the side or the top of the camera.
• When using the top cable exit configuration, drill a
hole in the ceiling to allow passage of the cables.
(See step 3 on page 15.)
• When using the side cable exit configuration,
prepare the cut-out in the die cast case and
decorative cover. (See “Preparing the Camera and
Decorative Cover for Side Cable Exit” on page 15.)
■ This camera is an indoor camera. It is not
designed for outdoor use.
■ This camera is designed for use in a hanging configuration only. Using it in an upright or inclined
configuration can cause malfunction and shorten
the life of the camera.
■ Install the camera in a horizontal configuration,
■ Noise interference considerations
with the dome pointed downwards.
When using a power line that is greater than 240 V AC
and wiring that is longer than 1 meter, wiring should be
performed using a separate metal conduit. (The metal
conduit must be earth grounded.)
■ Never install or use the camera in the following
locations.
• Areas directly exposed to rain and water
• Near a swimming pool or other areas where
chemicals are used
• Food preparation areas and other locations where
there are large amounts of steam vapour and oil, in
flammable atmospheres, other special environments
• Areas where radiation, X-rays, strong electric
waves, or magnetism is generated
• At sea, in coastal areas, or in areas where corrosive
gas is being generated
• Areas outside of the allowable ambient operating
temperature range (-10 °C to +50 °C)
• In a motor vehicle, on a boat, or other areas subject
to strong vibration (This camera is not designed for
■ Screws should be ordered separately.
The camera does not come with screws. Make sure
that the materials and structure of the installation
location is strong enough to support the total weight of
the camera.
-11-
WV-CS950 05.2.14 8:37 PM ページ12
■ Heat radiation
Important:
• Before setting up the camera for a configuration
where the camera's RS485 data port is used for
camera control (pan, tilt, etc.) by the system
controller, the camera's DIP switches must be
configured to specify the unit number and
communication parameters. (page 12)
If DIP switch setting is not performed, the
system controller control will not be possible
and camera set-up will have to be performed
again. Be sure to check the DIP switch settings
before setting up the camera.
The surface of the camera radiates heat. Ventilation
holes should be provided when installing the camera in
an enclosed ceiling or confined location where heat
can build up.
Ventilation holes
■ Beware of high humidity.
If the camera is installed when humidity is very high,
moisture may collect in the camera and cause the
dome to become foggy. If the dome becomes foggy,
remove it when the humidity is low and eliminate the
moisture inside the camera, and then replace the
dome. (page 7, 10)
DIP SWITCH SETTINGS
In a configuration where the camera's RS485 data port is used for camera control (pan, tilt, etc.) by the system
controller, the camera's DIP switches must be configured to specify the unit number and communication parameters.
The camera mounting base needs to be removed to access the DIP switches. See steps 1 and 2 on page 15 for
information about how to remove the camera mounting base.
DIP Switch 1
DIP Switch 2
ON
ON
1
2
3
4
5
6
7
1
8
2
3
4
■ Communication Parameters (DIP Switch 2)
The factory default settings of these DIP switches are all OFF.
ON
1
2
3
4
Communication
Parameters
Terminator
Switch 1: Terminator (Internal Termination Resistance)
Set it to ON in the following situations.
• When only one camera is connected.
• When only one camera is connected via a daisy chain over a long
distance.
Switches 2 through 4: Communication Parameters
This setting toggles between 2-line and 4-line communication.
Use these switches to select the communication protocol
being used.
ON
ON
1
2
3
4
4-line Communication
-12-
1
2
3
4
2-line Communication
WV-CS950 05.2.14 8:37 PM ページ13
■ Unit Number (DIP Switch 1)
The factory default settings of these DIP switches are all OFF. (Coaxial Multiplex System)
DIP Switch 1
Unit
Number
ON
1
ON
2
3
4
5
6
7
8
1 ~ 96 *
ON
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
2
2
3
4
5
6
7
8
3
2
3
4
5
6
7
8
4
2
3
4
5
6
7
8
5
2
3
4
5
6
7
8
6
2
3
4
5
6
7
8
7
2
3
4
5
6
7
8
8
2
3
4
5
6
7
8
9
2
3
4
5
6
7
8
10
2
3
4
5
6
7
8
11
2
3
4
5
6
7
8
12
5
6
7
24
8
1
1
1
1
1
1
1
1
1
1
2
3
4
5
6
7
8
13
1
2
3
4
5
6
7
25
8
2
3
4
5
6
7
8
14
1
2
3
4
5
6
7
26
8
2
3
4
5
6
7
27
8
2
3
4
5
6
7
2
3
4
5
6
7
28
8
2
3
4
5
6
7
29
8
2
3
4
5
6
7
2
3
4
5
6
7
30
8
2
3
4
5
6
7
31
8
3
4
5
6
7
8
2
3
4
5
6
7
32
8
2
3
4
5
6
7
8
2
3
4
5
6
7
33
8
2
3
4
5
6
7
34
8
2
3
4
5
6
7
35
8
3
4
5
6
7
2
3
4
5
6
7
36
8
2
3
4
5
6
7
3
4
5
6
7
8
2
3
4
5
6
7
8
ON
1
ON
1
3
4
5
6
7
8
3
4
5
6
7
8
48
1
2
3
4
5
6
7
8
49
1
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
1
1
1
1
1
1
1
1
1
2
3
4
5
6
7
8
51
52
53
54
55
56
57
58
59
60
1
2
3
4
5
6
7
8
61
1
ON
2
3
4
5
6
7
8
62
1
ON
2
3
4
5
6
7
8
2
3
4
5
6
7
8
63
1
ON
64
1
ON
2
3
4
5
6
7
65
1
8
ON
2
3
4
5
6
7
8
2
3
4
5
6
7
8
44
3
4
5
6
7
ON
1
45
2
66
1
ON
1
50
ON
ON
1
22
2
2
43
1
21
1
37
8
ON
2
47
ON
20
1
8
42
1
8
7
ON
ON
2
6
ON
19
1
5
41
1
ON
4
ON
ON
ON
3
ON
18
1
2
40
1
ON
1
ON
ON
2
46
ON
17
1
8
39
1
8
7
ON
16
1
6
ON
ON
ON
5
38
1
8
4
ON
15
1
3
ON
ON
ON
2
ON
ON
ON
1
ON
ON
ON
1
4
ON
ON
1
3
ON
ON
1
2
ON
ON
1
1
Unit
Number
ON
ON
ON
1
23
8
ON
ON
1
7
ON
ON
1
6
ON
ON
1
5
ON
ON
1
4
ON
ON
1
3
ON
ON
1
1
DIP Switch 1
ON
2
ON
ON
1
1
ON
ON
1
Unit
Number
DIP Switch 1
1
8
-13-
67
ON
68
WV-CS950 05.2.14 8:37 PM ページ14
DIP Switch 1
Unit
Number
ON
1
ON
2
3
4
5
6
7
8
69
ON
1
2
3
4
5
6
7
8
70
2
3
4
5
6
7
8
71
2
3
4
5
6
7
8
72
2
3
4
5
6
7
8
73
2
3
4
5
6
7
8
74
2
3
4
5
6
7
8
75
7
78
8
1
1
1
1
1
2
3
4
5
6
7
8
76
1
2
3
4
5
6
7
79
8
3
4
5
6
7
8
77
1
1
2
3
4
5
6
7
8
87
1
2
3
4
5
6
7
8
88
2
3
4
5
6
7
8
89
2
3
4
5
6
7
8
90
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
ON
2
3
4
5
6
7
80
8
1
ON
2
3
4
5
6
7
81
8
1
ON
2
3
4
5
6
7
82
8
1
91
ON
2
3
4
5
6
7
83
8
1
92
ON
2
3
4
5
6
7
84
8
1
93
ON
2
3
4
5
6
7
85
8
ON
2
Unit
Number
ON
ON
ON
1
6
ON
ON
1
5
ON
ON
1
4
ON
ON
1
3
ON
ON
1
1
DIP Switch 1
ON
2
ON
ON
1
1
ON
ON
1
Unit
Number
DIP Switch 1
1
94
ON
2
3
4
5
6
7
86
8
1
95
* When using the Unit Number 1 to 96 setting, the unit number setting needs to be configured using the RS485 SET UP menu. For details
about configuring this setting, see step 2 and page 20.
* Turning on power when this setting is selected causes the RS485 SET UP menu to appear during the initialisation routine.
■ RS485 Communication Parameters (DIP Switch 1)
Configuring DIP Switch 1 as shown below resets communication parameters to their factory default settings. You can
then change the settings as desired.
DIP Switch 1
Setting Description
ON
This setting resets communication parameters to the factory default settings.
1
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
ON
BAUD RATE : 19 200 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit
1
ON
BAUD RATE : 9 600 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit
1
ON
BAUD RATE : 4 800 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit
1
Perform the following steps to use this setting.
(1) Turn off the camera and use DIP Switch 1 to configure RS485 communication parameters as shown above.
(2) Turn on the camera.
This applies the setting you configured in step (1).
(3) Turn off the camera, use DIP Switch 1 to set the unit number (pages 13 and 14), and then turn the camera
back on again.
-14-
WV-CS950 05.2.15 10:43 AM ページ15
CAMERA INSTALLATION
■ Preparing the Camera and
Decorative Cover for Side Cable
Exit
2. Rotate the camera base unit in the direction
indicated by the arrow and remove it.
15°
The camera and decorative cover should be prepared
as shown below when mounting the camera on a
ceiling or wall with its cables (power, video output,
RS485, alarm in, alarm out) exiting from the side.
The camera mounting base needs to be removed in
order to prepare the camera. See steps 1 and 2 below
for information about how to remove the camera
mounting base.
* Prevent the dome cover from being scratched by
placing it on a soft cloth while you are working.
Rotate
Pull the camera
mounting base
up to remove it.
3. Using the camera mounting base as a template,
mark the locations of the four mounting holes on the
ceiling.
If you are using the top cable exit configuration,
mark the location of the cable hole on the ceiling
and drill the hole.
Preparing the Camera Die Cast Case*
Break it off
with a pair of
pliers.
Mark here
Preparing the Decorative Cover
4. Affix the camera mounting base onto the ceiling.
Use screws (M4) at the locations you marked above
to secure the mounting base to the ceiling.
If you do not plan to install the camera right away,
affix the dust protection sheet that comes with the
camera to the mounting base to keep dust off of it.
Cut it off
with a
razor knife.
■ Installing the Camera
• Select an installation location that is strong enough
to withstand the total weight of the camera.
Installing the camera at a location that is too weak
can cause it to fall.
• Remove the protective sheet after the installation
work is complete.
• If you are using an optional bracket to install the
camera, install the bracket in accordance with the
instructions that come with it.
1. Remove the fixing screw (M3 × 6) that secures the
camera to the mounting base.
Put the screw in a place where it will not become
lost.
Screws
(M4, available separately)
Dust Protection Sheet
(comes with camera)
Fixing screw
After loosening
the screw, press
upwards on the
camera and then
remove it.
-15-
WV-CS950 05.2.14 8:37 PM ページ16
9. Separate the two parts of the decorative cover
(comes with camera).
Press upwards on the decorative cover at the
points marked
(indicated by the arrows, in the
illustration below) to unhook the two parts from
each other.
* When removing the decorative cover, the direction
to press ( ) is shown on the side of the decorative
cover.
5. Attach the safety wire for securing the camera to
the mounting base.
Pull on the safety wire to make sure its ring is
securely connected to the mounting base hook.
If the dust protection sheet that comes with the
camera is affixed to the mounting base, remove it
before performing the above step.
➡
Back
Unhook
Fix securely
Safety
wire ring
Press
Fix securely
Note: The safety wire is designed to allow the
camera to hang from it. Do not apply force greater
than the weight of the camera to the wire.
Caution: Pressing up on the wrong side of the
decorative cover can damage it.
10. Put the two pieces of the decorative cover on the
left and right side of the camera, and hook them
together.
Align the hooks and press the piece indicated by
the arrow in the illustration below into the other
piece.
6. Install the camera onto the mounting base.
Aligning with the mounting base, press down on the
camera as far as it will go and rotate in the direction
indicated by the arrow.
7. Use the fixing screw you removed in step 1 to
secure the camera to the mounting base.
8. Check the installation.
• Is the camera is level and installed securely?
• Is the camera free of looseness?
• Does the fixed part of the camera remain in place
when you try to rotate it?
15°
Camera
Press
Back
Hold
securely
Hold
securely
Align
hook
Press
Press
11. Slide the decorative cover up to the ceiling.
• In the case of a top cable exit configuration, slide
the decorative cover straight up and press it firmly
against the ceiling.
• In the case of a side cable exit configuration, align
the cut-out in the decorative cover with the cables
as you slide it up, and press it firmly against the
ceiling.
Rotate
Camera
Mounting
Base
Top Cable Exit
Configuration
Side Cable Exit
Configuration
Align with
cut-out
-16-
WV-CS950 05.2.14 8:37 PM ページ17
UNINSTALLING THE CAMERA
Caution: Make sure you perform the steps below
carefully and exactly when uninstalling the camera
and decorative cover. Failure to do so creates the
risk of damage to the camera.
■ Removing the Decorative Camera
Note that you need to separate the two parts of the
decorative cover in order to remove it.
1. Unhook the two parts of the decorative cover.
Press upwards on the decorative cover at the
points marked
(indicated by the arrows, in the
illustration below) to unhook the two parts from
each other.
* When removing the decorative cover, the direction
to press ( ) is shown on the side of the decorative
cover.
➡
Unhook
Back
Fix securely
Press
Press
Fix securely
■ Uninstalling the Camera
The camera and its base unit are secured by screws.
This configuration provides double anchoring, and you
should use the following procedure to uninstall the
camera.
1. Remove the fixing screw that secures the camera to
the mounting base.
Put the screw in a place where it will not become
lost.
2. Remove the camera from the mounting base.
Rotate the camera in the direction indicated by the
arrow and remove it.
Fixing screw
After loosening
the screw, press
upwards on the
camera and then
remove it.
Rotate
Camera
15°
Camera
Mounting
Base
3. Remove the safety wire from the mounting base.
-17-
WV-CS950 05.2.14 8:37 PM ページ18
CONNECTIONS
Precautions
• The following connections should be made by qualified service personnel or system installers in accordance
with all local codes.
• See the reverse side of the cover page for main lead connection.
220 V - 240 V AC
(WV-CS950)
24 V AC Cable for camera
24 V AC (WV-CS954E)
RS485 Data Port
Twisted Pair Cable*1
To Matrix Switcher,
etc.
(RJ-12)
Video Output
Connector
Coaxial Cable (5C-2V)*2
To VIDEO IN port
(CAMERA IN)
(BNC)
Alarm Input
Connector
8P Alarm Cable (provided)
To sensor, etc.
Alarm Output
PP Alarm Cable (provided)
Connector
To buzzer,
display device, etc.
*1: For twisted pair cable, use shielded low-impedance cable with a thickness of at least AWG#22
(0.33 mm2).
*2: Keep the overall length of coaxial cable under 1200 meters (in the case of 5C-2V).
*3: Be sure to connect the grounding cable to ground.
Alarm Input Connector
RS485 Data Port
Red
Data
Tx
Data
Rx
T(B)
T(A)
R(B)
R(A)
Orange
Yellow
Green
(RJ-12)
Alarm Output Connector
Alarm In 1 (Black)
GND (Brown)
Alarm In 2 (Red)
GND (Orange)
Alarm In 3 (Yellow)
GND (Light Blue or Green)
Alarm In 4 (Blue)
GND (Violet)
Alarm Out 1 (Grey)
GND (White)
Alarm Out 2 (Pink)
GND (Light Green
or Light Blue)
• 24 V AC Power Supply Connection
Alarm In/Out Ratings
Alarm In : 5 V DC pull-up input. Drive capacity of at
lease 0.2 mA required.
OFF : 4 V DC minimum 5 V DC maximum,
or open
ON : 1 V DC maximum or short
Alarm Out : Open collector output. 16 V DC, 100 mA
maximum drive capacity
OFF : Open
ON : 100 mA maximum
* When connecting to an external device, set up the
system so the ratings are not exceeded.
Recommended wire gauge sizes for 24 V AC line
Copper wire size
(AWG)
Length
of cable
(approx.)
#20
#18
#24
#22
(0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2)
(m)
20
30
45
75
(ft)
65
100
160
260
Accessory Connector Information
Pin no.
Note: Do not turn off camera power within 30 seconds
after turning it on. Doing so can cause pan, tilt, zoom,
or focus to go out of position.
-18-
Power source
1
24 V AC LIVE
2
24 V AC NEUTRAL
4
3
3
Ground
2
1
4
Not use
WV-CS950 05.2.14 8:37 PM ページ19
How to Assemble the Cable with the Accessory
Connector
Strip back the cable jacket approx. 3 mm and separate
the individual conductors.
Approx.
3 mm (0.1 inch)
Approx. 3 mm
Wire
Wire
Up A
Up
Contact
Contact
Insert
Insert
position
Insertthe
thewire
wireuntil
untilA A
position
and
contacts.
andclamp
clampthe
the
contacts.
Prepare the individual conductors for clamping. Use
MOLEX band tool part number 57027-5000 (for ULStyle Cable UL1015) or 57026-5000 (for UL-Style
UL1007) for clamping the contacts.
After clamping the contacts, push them into the proper
holes in the accessory connector of this camera until
they snap in place.
Up
Wire
Contact
Cautions:
• Shrinking the cable-entry seal is a one-time
procedure. Do not shrink the cable-entry seal until
ascertaining that the unit is functioning.
• CONNECT THIS TO 24 V AC CLASS 2 POWER
SUPPLY ONLY.
-19-
WV-CS950 05.2.15 6:12 PM ページ20
RS485 SET-UP
8. Move the cursor to WAIT TIME, and then tilt the
joystick left or right to select a wait time setting.
The wait time is the time that the camera should
wait before resending data when no receive
acknowledgement (ACK) is returned after data is
sent.
Tilting the joystick cycles through the wait time
display in the sequence shown below. (unit: ms)
The factory default setting is OFF.
Use the following procedure to configure the RS485
setup when you want to use the system controller to
control the camera (pan, tilt, etc.) via the camera's data
port.
1. Display the setup menu (page 21), move the cursor
to COMMUNICATION O, and then press the CAM
(SET) button.
This will display the RS485 set-up menu.
2. Check the unit number. (page 13)
The UNIT NUMBER item shows the unit number
specified by DIP Switch 1. The factory default unit
number is 1.
If DIP Switch 1 specifies 1 to 96 as the unit number,
move the cursor to UNIT NUMBER and then tilt the
joystick left or right to select a unit number (1 to 96).
OFF ↔ 100MS ↔ 200MS ↔ 400MS ↔ 1000MS
9. Move the cursor to ALARM DATA, and then tilt the
joystick left or right to select an alarm data send
mode setting.
POLLING : Sends alarm data in response to a
request by the system controller.
AUTO1 : Sends alarm data each time an alarm
signal is input.
AUTO2 : Sends alarm data at five-second intervals.
This is the factory default setting.
10. Move the cursor to DELAY TIME, and then tilt the
joystick left or right to select a delay time setting.
The delay time is the time is the time the camera
should wait before sending a receive acknowledge
(ACK). The delay time display changes in the
sequence shown below. (unit: ms) The factory
default setting is OFF.
** RS485 SETUP **
1
UNIT NUMBER
----SUB ADDRESS
19200
BAUD RATE
8
DATA BIT
NONE
PARITY CHECK
1
STOP BIT
NOT USE
XON/XOFF
OFF
WAIT TIME
AUTO2
ALARM DATA
OFF
DELAY TIME
RET TOP
Note: It is not necessary to configure the RS485
SET UP menu SUB ADDRESS setting.
3. Move the cursor to BAUD RATE, and then tilt the
joystick left or right to select a baud rate setting.
Tilting the joystick cycles through the baud rate
(transmission speed) display in the sequence
shown below. (unit: bits/s) The factory default
setting is 19200.
2400
4800
9600
OFF ↔ 100MS
This setting can be configured only when 2-line
configuration is selected by DIP Switch 2. (page 12)
19200
4. Move the cursor to DATA BIT, and then tilt the
joystick left or right to select a data bit setting (7 or
8).
The factory default setting is 8.
5. Move the cursor to PARITY CHECK, and then tilt the
joystick left or right to select a parity bit setting
(NONE, ODD, EVEN).
The factory default setting is NONE.
6. Move the cursor to STOP BIT, and then tilt the
joystick left or right to select a stop bit setting (1 or
2).
The factory default setting is 1.
7. Move the cursor to XON/XOFF, and then tilt the
joystick left or right to select an XON/XOFF setting.
The factory default setting is NOT USE.
NOT USE: Disables X ON/X OFF data flow control.
USE
: Enables X ON/X OFF data flow control.
-20-
WV-CS950 05.2.14 8:37 PM ページ21
USING THE SET-UP MENU
■ Language Setting
For details about operations, see the operating
instructions for the equipment you are using.
MODEL
WV-CS950 SERIES
CAMERA
PAN/TILT
ALARM
SPECIAL
COMMUNICATION
SCENE SELECT
LANGUAGE
This manual describe procedures for operating system
controller WV-CU650.
All setting configuration procedures start from the
setup menu. This section explains how to display the
setup menu and provides details about the menu items
that it contains.
→QUICK SETUP
PASSWORD LOCK OFF
■ Displaying the Set-up Menu
1. Move the cursor to LANGUAGE O, and then press
the CAM (SET) button.
2. On the 8-language selection menu that appears,
select the language you want to use.
* All of the example screens in these Operating
Instructions show English display messages.
3. Move the cursor to SET, and then press the CAM
(SET) button.
When you switch the languages, the password and
titles are deleted.
* If you have selected either Japanese or Chinese as
the language, only the IDs and titles can be set in
katakana or Chinese.
* The “LANGUAGE” display remains in English even
when the language setting is changed.
● When using the WV-CU650
(1) Select the camera you want to set up (this
camera), and the monitor where you want to
display the set-up menu.
(2) Press the MENU button to display LCD MENU
CAM 101.
(3) Press the ENTER button or CAM (SET) button to
display CAMERA SET-UP.
(4) Press the F1 button.
MODEL
WV-CS950 SERIES
CAMERA
PAN/TILT
ALARM
SPECIAL
COMMUNICATION
SCENE SELECT
LANGUAGE
→QUICK SETUP
PASSWORD LOCK OFF
q
w
e
r
t
y
u
o
i
Refer to the pages below for details of setup menu
items.
q
w
e
r
t
CAMERA
PAN/TILT
ALARM
SPECIAL
COMMUNICATION*
y SCENE SELECT
u LANGUAGE
i QUICK SETUP
o PASSWORD LOCK
Camera Settings
Page 22
Pan and Tilt
Page 27
Alarm Settings
Page 36
Special Settings
Page 39
Communication Settings
Page 20
Scene Select Settings
Page 40
Language Setting
This page
Quick Menu Settings
Page 41
Password Settings
Page 42
* This item appears only when RS485 settings are
configured with the DIP switches.
-21-
WV-CS950 05.2.14 8:37 PM ページ22
CAMERA SETTINGS
■ Using the Camera Set-up Menu
CAMERA ID--0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$
Display the camera set-up menu from the set-up
menu to configure camera settings. First, display
the camera set-up menu.
1. Display the set-up menu (page 21), move the cursor
to CAMERA O, and then press the CAM (SET)
button.
This will display the camera set-up menu.
SPACE
---- POSI RET RESET
DOOR............
Camera ID Input area
**CAMERA SETUP** 1/2
CAMERA ID
OFF
ALC/MANUAL ALC
SHUTTER
AUTO
AGC
ON(MID)
SENS UP
OFF
SYNC
INT
WHITE BAL
ATW1
DNR
LOW
RESOLUTION HIGH
BW MODE
AF MODE
AUTO L
q
e
t
u
o
!1
**CAMERA SETUP** 2/2
ZOOM LIMIT ×30
STABILIZER OFF
!2
4. Move the cursor to POSI, and then press the CAM
(SET) button.
This will display the ID position setting menu.
5. Use the joystick to select a camera ID display
position, and then press the MON (ESC) button.
This registers the camera ID display position and
returns to the camera setting menu.
w
r
y
i
!0
!3
DOOR
RET TOP
* The following sections numbered q to !3 explain
how to use each of the camera set-up menu items.
(1) Camera ID (CAMERA ID)
The camera ID is a series of alphanumeric
characters that indicate the location of the camera.
This item can be used to turn display of the camera
ID on the monitor screen on or off, and to input the
camera ID.
1. Move the cursor to CAMERA ID, and then tilt the
joystick left or right to toggle camera ID display on
and off.
2. Select ON or OFF, and then press the CAM (SET)
button.
3. Use the joystick to move the cursor the character
you want to input, and then press the CAM (SET)
button.
This will cause the selected character to appear in
the camera ID input area. Repeat step 3 as many
times as necessary to input all of the characters for
the camera ID. (Example: DOOR)
To input a blank space
Move the cursor to SPACE, and then press the
CAM (SET) button.
To delete previously input characters
Move the cursor to RESET, and then press the CAM
(SET) button.
To change previously input characters
Use the joystick to move the cursor to the camera
ID input area. Next, tilt the joystick left and right to
move the ↑ pointer to the character you want to
change. Finally, use step 3 above to input the new
character.
(2) Light Control (ALC/MANUAL)
1. Move the cursor to ALC/MANUAL, and then tilt the
joystick left or right to toggle between ALC and
MANUAL.
ALC
: Enables automatic lens iris adjustment in
accordance with subject brightness.
Select this ALC when using SUPER-D 3.
MANUAL: Adjust the lens iris with the IRIS button
on the system controller. Fixes the lens
iris.
Note: The backlight compensation submenu
associated with this menu is described separately
and should be set up after installing the camera at
the site and observing the actual site picture.
2. If ALC is set in step 1, press the CAM (SET) button
to set SUPER-D 3.
SUPER-D 3 (Super Dynamic 3)
When there is wide variation between the illumination of
light and dark areas of the location being monitored,
the camera adjusts the lens iris in accordance with the
bright areas. This causes loss of detail in dark areas.
Conversely, adjusting lens brightness for the dark
areas cause brighter area to become washed out.
SUPER-D 3 digitally combines an image that is set up
for a clear view of bright areas with an image that is set
up for a clear view of dark areas, creating a final image
that preserves overall detail.
-22-
Loss of detail
in dark areas...
and left switches simultaneously.
(3) After masking all of the cells you want, press the
MON (ESC) button to return to the ALC CONT
menu in step 1.
Wash out of
bright areas ...
Two images
digitally combined
to create a clear
final image
6. Move the cursor to LEVEL, and then tilt the joystick
left and right to adjust the picture output level
(picture contrast).
If you selected ON in step 3 of this procedure, best
results can be obtained by setting a contrast level
that is somewhat high. A contrast level that is too
high, however, may increase the tendency of
afterimages and noise.
Notes:
• SUPER-D 3 is supported only when ALC is
selected for light control (ALC/MANUAL).
• Camera settings are limited to the following when
SUPER-D 3 is turned on.
SHUTTER : OFF, AUTO (This page)
SENS UP : OFF, AUTO (page 24)
• If lighting conditions cause either of the following
phenomena, turn off SUPER-D 3.
(1) Screen flickering or abnormal colour
(2) Digital noise in the bright areas of the screen
Note:
• If operation of the system controller's IRIS
(OPEN, CLOSE) button during operation is done
after the menu is closed, the LEVEL on the
CAMERA menu is reflected and stored for these
settings. However, if the camera is in a preset
position, it is reflected as a parameter of the
preset position. To return to the initial factory
default level, execute the system controller’s iris
reset.
• When the Light Control is in ALC, “IRIS-CLOSE”
is displayed below the pan/tilt/zoom position
display when the iris is completely closed. When
the Light Control is in MANUAL, “IRIS-CLOSE” is
not displayed.
3. Move the cursor to SUPER-D3, and then tilt the
joystick left or right to toggle between on and off.
ON : Turns on SUPER-D 3. (Go to Step 6)
OFF : Turns off SUPER-D 3. (Go to Step 4)
**ALC CONT**
BACK LIGHT COMP
SUPER-D3
OFF
MASK SET
LEVEL
••••I••••
+
RET TOP
(3) Shutter Speed (SHUTTER)
1. Move the cursor to SHUTTER, and then tilt the
joystick left or right to select a shutter speed
setting.
Tilting the joystick cycles through the shutter speed
settings display in the sequence shown below.
(unit: sec)
4. Move the cursor to MASK SET O, and then press
the CAM (SET) button.
This will display the mask area screen, with the
cursor in the upper left cell.
5. Mask the cells in the area where background
lighting is bright. Masking an area will cause its
brightness level to be ignored.
Use the following steps to perform masking
(1) Tilt the joystick up and down, and left and right
to move the cursor to a cell you want to mask.
(2) Press the CAM (SET) button to mask the cell.
Moving the cursor to a cell that is already
masked causes the blinking pattern of the
cursor to alternate between horizontal stripes
and white.
Pressing the CAM (SET) button while the cursor
is located at a masked cell cancels the masking
of the cell.
To cancel all masking areas, press the F2 button
of WV-CU550C. For WV-RM70, press the right
When SUPER-D 3 is turned off
OFF ↔ AUTO ↔ 1/120 ↔ 1/250 ↔ 1/500 ↔ 1/1000
1/10000 ↔ 1/4000 ↔ 1/2000
When SUPER-D 3 is turned on
OFF ↔ AUTO
AUTO: This setting, by moving the shutter
automatically when necessary, provides a
clearer picture of extremely bright objects
outdoors, etc.
OFF : Fixed at 1/50 seconds.
-23-
WV-CS950 05.2.14 8:37 PM ページ24
(1) Multiplexed vertical drive (VD2)
(2) Internal sync (INT)
(3) Line-lock (LL)
Input of a multiplexed vertical driver (VD2) signal
automatically switches to VD2 sync, regardless of the
camera's current sync mode (SYNC). In this case, the
camera setting menu shows EXT (VD2) for the SYNC
setting, which cannot be changed to internal sync
(INT) or line-lock (LL).
The following procedures explain how to select internal
sync (INT) and line-lock sync (LL), and how to perform
phase adjustment when line-lock sync (LL) is selected.
1. Move the cursor to SYNC, and then tilt the joystick
left or right to select the sync mode.
INT : Internal sync
LL : Line-lock (Cannot be used in areas with 50 Hz
power.)
Selecting LL and pressing the CAM (SET) button
will display the SYNC setting menu, which can be
used for configuring detailed settings. (This page)
Notes:
• When AUTO is selected for the shutter setting,
fluorescent lighting may cause flickering of the
picture. If this happens, select OFF or 1/100 for
the shutter speed setting.
• AUTO is disabled when MANUAL is selected for
light control (ALC/MANUAL) and FIX is selected
for electronic sensitivity enhancement (SENS UP).
(4) Gain Control (AGC)
1. Move the cursor to AGC, and then tilt the joystick
left or right to select a gain control setting.
ON (LOW) : Low gain
ON (MID) : Medium gain
ON (HIGH) : High gain
OFF
: Fixed gain
Note: When AGC is turned on, the noise reduction
function automatically activates under low illumination
to reduce digital noise. This also, however, can cause
afterimages to be generated by moving objects, and
by panning and tilting the camera. For more
information, see the DNR setting (page 25).
● Adjusting the Phase for Line-lock
Synchronization
Connect the video output signal of the camera being
adjusted and the reference video output signal to a
two-input oscilloscope.
Set the oscilloscope to the vertical rate, and then
expand the vertical sync portion on the oscilloscope.
1. Move the cursor to COARSE, and then tilt the
joystick left or right to align the coarse adjustment
of the vertical phases of the camera being adjusted
with that of the reference camera.
Coarse adjustment be performed across 16 steps
(1 through 16). Adjusting past step 16 returns to
step 1.
(5) Electronic Sensitivity Enhancement (SENS UP)
1. Move the cursor to SENS UP, and then tilt the
joystick left or right to select an electronic sensitivity
enhancement setting.
The electronic sensitivity enhancement setting can
be changed only when OFF or AUTO is selected for
the shutter speed (SHUTTER) setting. Tilting the
joystick cycles through the settings display in the
sequence shown below.
When SUPER-D 3 is turned off
↔
↔
OFF ↔ X2 AUTO ↔ X4 AUTO ↔ X6 AUTO ↔ X10 AUTO ↔ X16 AUTO
X16 FIX
X32 AUTO
↔
X10 FIX
↔
X6 FIX
↔
X4 FIX
↔
X2 FIX
↔
** SYNC **
↔
↔
X32 FIX
OFF
V PHASE
When SUPER-D 3 is turned on
COARSE
OFF ↔ X2 AUTO ↔ X4 AUTO ↔ X6 AUTO
FINE
X32 AUTO
1(1--16)
••••I••••
+
↔ X16 AUTO ↔ X10 AUTO
Note: The following are the differences between
AUTO and FIX.
AUTO: Selecting X32 AUTO, for example,
automatically increases sensitivity, up to
a maximum of 32 times.
FIX : Selecting X32 FIX, for example,
increases sensitivity 32 times.
The FIX settings cannot be selected when the
shutter speed (SHUTTER) setting is 1/120.
RET TOP
2. Move the cursor to FINE, and then tilt the joystick
left or right to align the fine adjustment of the
vertical phases of the camera being adjusted with
that of the reference camera.
Notes:
• To reset COARSE and FINE to the preset values,
press the F2 button. For WV-RM70, press the
right and left switches simultaneously. COARSE
is preset to zero-crossing of the AC line phase.
• If the AC line phase contains spike noise, etc.,
the vertical phase of the video output signal may
be disturbed.
Caution: Turning on SENS UP can cause digital noise
and white spots (blemish) to appear in the picture.
(6) Synchronization (SYNC)
This camera supports the following three sync modes,
which are listed in priority sequence from highest
priority to lowest.
-24-
WV-CS950 05.2.14 8:37 PM ページ25
(8) Digital Noise Reduction (DNR)
1. Move the cursor to DNR, and then tilt the joystick
left or right to select a digital noise reduction (DNR)
setting.
LOW : Low DNR, Low afterimage
HIGH : High DNR, High afterimage
(7) White Balance (WHITE BAL)
1. Move the cursor to WHITE BAL, and then tilt the
joystick left or right to select a white balance mode.
(1) Auto-Tracing White Balance Mode (ATW1/ATW2)
In this mode, the camera continually monitors
the color temperature of the light source and
automatically adjusts white balance.
The following are the approximate supported
colour temperature ranges in this mode.
ATW1: 2,700 K to 6,000 K
ATW2: 2,000 K to 6,000 K (Mode recommended
for sodium lighting)
Proper white balance may not be possible under
the following conditions. In such cases, use the
AWC while balance mode.
• When the subject contains mostly dark colours
• When the light source is a deep blue sky or
twilight
• When illumination of the subject is low
(2) Auto-Tracing White Balance Control (AWC)
In this mode, the supported color temperature
range is approximately 2,000 K to 10,000 K. This
mode is best in locations where the light source
is constant.
(a) To select AWC, tilt the joystick left and select
AWC→PUSH SET.
(b) Press the CAM (SET) button to start white
balance adjustment. PUSH SET is highlighted
on the display while white balance adjustment is
being performed.
• PUSH SET becomes unhighlighted again when
white balance adjustment is complete. Tilt the
joystick right to display AWC.
• If white balance adjustment cannot be completed
for some reason, PUSH SET will remain
highlighted on the display. If this happens, it could
mean that the colour temperature is outside the
supported range, or that illumination is too low.
2. Select ATW1, ATW2, and AWC, then press the CAM
(SET) button, either the ATW setting menu or the AWC
setting menu appears, and you can fine tune the
white balance.
Move the cursor to R or B, and then tilt the joystick left
or right to fine tune the level. The R is red and the B is
blue, moving in the + direction makes the colours
darker, moving in the - direction makes them lighter.
(9) Resolution (RESOLUTION)
1. Move the cursor to RESOLUTION, and then tilt the
joystick left or right to select NORMAL or HIGH.
NORMAL : Sets horizontal resolution to a minimum
of 480 lines. (In colour mode)
HIGH
: Sets horizontal resolution to a minimum
of 520 lines. (In colour mode)
(10) Black and White Mode (BW MODE)
Moving the cursor to BW MODE and pressing the CAM
(SET) button displays a BW MODE setting menu.
Use the BW MODE setting menu to configure black
and white mode settings.
1. Move the cursor to BW, and then tilt the joystick left
or right to select a black and white control setting.
AUTO : The
camera
automatically
switches
between the colour mode and the black
and white mode in accordance with picture
brightness (illuminance).
The black and white mode is selected
when lighting is low, while the colour mode
is selected for bright lighting.
ON
: Selects the black and white mode.
OFF : Selects the colour mode.
** BW MODE **
BW
LEVEL
DURATION
BURST(BW)
••••I••••
+
B
••••I••••
+
AUTO
HIGH
•I••
S L
ON
RET TOP
Note: The above setting cannot be configured
when BW is selected for the ALARM IN 4 setting
(page 38).
2. If you selected AUTO in step 1, move the cursor to
LEVEL and then tilt the joystick left to select the
threshold illuminance level for switching between
the color mode and the black and white mode.
The illuminance shown below is based on the
assumption that the camera is used in an area lit by
halogen lamps, and that AGC on the menu is set to
MID.
LOW : Switches to the black and white mode when
illuminance
around
the
camera
is
approximately 1.5 lux or lower (when AGC
ON (MID), SENS UP OFF is set).
HIGH : Switches to the black and white mode when
illuminance
around
the
camera
is
approximately 3 lux or lower (when AGC
ON (MID), SENS UP OFF is set).
** ATW1 **
R
TIME
RET TOP
Note: White balance is adjusted in accordance with
on-screen color temperature, which the camera
detects automatically. Correct adjustment may not
be possible if a strong light source is shining on the
screen.
-25-
WV-CS950 05.2.15 10:43 AM ページ26
• Pictures that are a mixture of distant and nearby
objects
• White walls and other single-colour objects
• Venetian blinds and other vertically striped
objects
• Slanted objects
• Objects illuminated with low lighting
Auto-focus focuses on the object in the centre of
the picture, so objects around the outside periphery
of the picture will not be in focus.
Note: When near-infrared lamps are used, the
image may be displayed out of focus and mode
switching may not perform automatically.
3. If you selected AUTO in step 1, move the cursor to
DURATION TIME and then tilt the joystick left to
select the time the camera should wait before
switching between the colour mode and the black
and white mode after there is a change in the
illuminance level.
Available Settings: 10 s - 30 s - 60 s - 300 s
(S)
(L)
Note: When AUTO is selected, switching between
the colour mode and the black and white mode is
not performed while pan, tilt, zoom, or focus is
being performed.
(12) Zoom Limit (ZOOM LIMIT)
1. Move the cursor to ZOOM LIMIT, and then tilt the
joystick left or right to select a zoom limit setting.
When doing manual operation, zoom operation
cannot go beyond the zoom limit.
Optical zoom ranges from 1 to 30 magnifications,
while digital zoom is used for higher magnifications
(up to 300).
4. Move the cursor to BURST (BW), and then tilt the
joystick left or right to turn burst signal output on or
off.
This setting is for black and white mode display.
ON : Turns on burst signal output.
OFF: Turns off burst signal output.
Notes:
• If zoom limit is set to more than 30x, then zoom
operation pauses at 30x magnification.
• Increasing the zoom to over 30x magnification
(digital zoom) decreases the resolution.
• You cannot set a zoom magnification of greater
than 30x as a preset position.
Note: With some monitors and VCR models, output
of a camera images in the black and white mode
will not display a proper image unless a burst signal
is provided. Select ON for this setting when using
equipment that requires a burst signal.
(13) Auto Image Stabilizer (STABILIZER)
This function electronically compensates for an
unstable camera image due to movement of a
mounting pole or bracket.
1. Move the cursor to STABILIZER, and then tilt the
joystick left or right to turn the stabilizer on or off.
The default setting is OFF.
ON : Automatically compensates for an unstable
image.
OFF: Image stabilizer will not operate.
(11) Auto Focus (AF MODE)
1. Move the cursor to AF MODE, and then tilt the
joystick left or right to select an auto-focus mode
setting.
MANUAL S.M.L : Activates auto-focus when the AF
button on the system controller is
pressed.
AUTO S.M.L
: Auto focus is used automatically
when PAN, TILT or ZOOM are
used in manual operation.
The letters S (Small), M (Medium), and L (Large)
indicate the size of the auto-focus sensing area.
Notes:
• The stabilizer may not be effective for the
following subjects.
Example: • Objects illuminated with low lighting
• Single-colour objects (white walls etc)
• Fast moving periodic action, such as
mechanical vibration, may not be tracked.
• The stabilizer does not work during
PAN/TILT/ZOOM/FOCUS or when the camera
setup menu is open.
• When set to ON, some effective pixels on the
edge of the CCD are used by the stabilization
function. This may result in a small reduction in
resolution and a narrower angle of view. After
activating the image stabilizer function, check
that the field of view is correct.
• Image stabilization may not function where there
is excessive camera movement or when the
scene is low light or low contrast objects.
Notes:
• The AUTO (S.M.L.) setting can be selected only
when OFF, x2 FIX or x2 AUTO is selected for the
electronic sensitivity enhancement (SENS UP).
Any other SENS UP setting causes MANUAL
(S.M.L.) to be selected automatically for the
auto-focus mode (AUTO AF).
• Zooming up from WIDE can cause the image to
go out of focus.
• Auto-focus may not be possible with the types of
objects listed below. For such objects, focus
manually.
Example:
• Shiny or high intensity objects
• Objects shot through wet or dirty glass
-26-
WV-CS950 05.2.14 8:37 PM ページ27
PAN / TILT
■ Using the Pan/Tilt Set-up Menu
(2) Position Number Selection (MAP)
You could use the MAP item on the pan/tilt set-up
menu instead of the PRESET item to select a position
number.
1. Move the cursor to MAP O, and then press the
CAM (SET) button.
Display the pan/tilt set-up menu from the set-up menu
to configure pan and tilt settings.
First, display the pan/tilt set-up menu.
Use a shortcut (page 45) to switch between displaying
or not displaying the pan, tilt, and zoom positions
(during pan, tilt and zoom operation) on the monitor
screen.
* The tilt position is displayed ranging from –5˚ to 90˚
to –5˚.
**PRESET POSITION**
4
1*
2
3
8
5
6
7
12
9
10
11
16
13
14
15
20
17
18
19
24
21
22
23
28
25
26
27
32
29
30
31
ID:DOOR
033-064 225-256
RET TOP
2. Move the cursor to the number you want to select,
and then press the CAM (SET) button.
This registers the position number setting and
displays the preset setting menu. (this page)
To select a position number in the range of 033 to
064, move the cursor to 33-64 in the lower left corner
of the menu, and then press the CAM (SET) button.
Preset numbers set subsequently are the same.
360°/ 90°/X001
Pan position Zoom ratio
Tilt position*
1. Display the setup menu (page 21), move the cursor
to PAN/TILT O, and then press the CAM (SET)
button.
This will display the pan/tilt set-up menu.
**PAN/TILT
PRESET
1
MAP
HOME POSITION
SELF RETURN
AUTO MODE
AUTOPAN KEY
PATROL
PRIVACY ZONE
IMAGE HOLD
DIGITAL FLIP
PROPO.P/T
SETUP**1/2
**PAN/TILT
AREA TITLE
TILT ANGLE
CLEANING
SETUP**2/2
ON(USER)
0°
OFF
OFF
OFF
OFF
AUTO PAN
OFF
OFF
ON
ON
q
e
t
u
o
!1
**PRESET POSITION**
36
33
34
35
40
37
38
39
44
41
42
43
48
45
46
47
52
49
50
51
56
53
54
55
60
57
58
59
64
61
62
63
ID:
065-096 001-032
RET TOP
w
r
y
i
!0
Notes:
• An asterisk (*) to the right of a position number
indicates that it already has a preset position
assigned to it.
The home position number is indicated by the
letter H next to the asterisk.
• When the cursor is located at a position number
that has a position ID, the position ID text
appears next to ID: on the menu screen.
!2
!3
!4
RET TOP
● Position Setting (POSITION SET)
* The following sections numbered q to !4 explain
how to use each of the pan/tilt set-up menu items.
The position setting can be used to specify the camera
position (pan and tilt), the lens zoom setting, and the
focus setting.
1. Move the cursor to POSITION SET O and press the
CAM (SET) button to display the position setting menu.
(1) Position Number Selection (PRESET)
Positions can be assigned numbers, each of which can
be configured with a monitoring position and
monitoring conditions.
You can use either the PRESET item or the MAP item on
the pan/tilt set-up menu to select a position number.
Position numbers 1 through 4 are used for alarm
functions (pages 37 and 38) and operating them.
1. Move the cursor to the 1 next to the PRESET item,
and then tilt the joystick left or right to change the
position number to the one you want.
2. Press the CAM (SET) button.
This registers the position number setting and
displays the preset setting menu. (this page)
PRESET NO.
1*
POSITION SET
PRESET ID
ON
ALC/MANUAL
ALC
AF MODE
MANUAL L
DWELL TIME
10S
SCENE FILE
OFF
PRESET SPEED
••••••••I
L
H
RET TOP DEL
-27-
2. Move the cursor to →PUSH SET to the right of
PAN/TILT, and then press the CAM (SET) button to
display the PAN/TILT setting menu.
WV-CS950 05.2.14 8:37 PM ページ28
● Adjusting Camera Position When
Changing Cameras (PAN OFFSET SET)
** POSITION 1 **
PAN/TILT
→PUSH SET
ZOOM/FOCUS
→PUSH SET
PAN OFFSET SET ←
The system controller etc. has a function for
downloading (saving) and uploading (recovering)
setting information for the camera. This function allows
you to upload (recover) original setting information that
has been downloaded (saved) before some
unforeseen damage or malfunction causes setting
information in the camera to be lost. However, there
may be some slight differences in images from those
uploaded (recovered) when the camera is changed.
The "PAN OFFSET SET" function is for adjusting these
differences.
1. Align the cursor with "PAN OFFSET SET" with the ← or
→ arrow, and press the CAM (SET) button to set the
offset value.
Set the offset value to 0.0, or in a range of -10 to
+10. All preset positions for the camera's position
are adjusted according to the offset value.
→
0
RET TOP
FLOOR1
DOOR
3. Use the joystick to position the camera, and then
press the CAM (SET) button.
** POSITION 1 **
→PUSH SET
PAN/TILT
→PUSH SET
ZOOM/FOCUS
U TILT D/L PAN R
PAN OFFSET SET ←
0
→
RET TOP
FLOOR1
DOOR
4. Move the cursor to → PUSH SET to the right of
ZOOM/FOCUS, and then press the CAM (SET)
button to display the ZOOM/FOCUS setting menu.
Important: Data is not compatible with existing
cameras. Uploading setting information from
existing cameras will damage data in the camera. If
data in the camera is damaged, download camera
setting information from a camera that still has the
factory settings and then upload it to the camera
with the damaged data.
** POSITION 1 **
PAN/TILT
→PUSH SET
ZOOM/FOCUS
→PUSH SET
U ZOOM D/L FOCUS R
PAN OFFSET SET ←
0
→
RET TOP
FLOOR1
DOOR
● Preset ID Setting (PRESET ID)
The preset ID is a series of alphanumeric characters
that indicate the location of the camera. This item can
be used to turn display of the preset ID on the monitor
screen on or off, and to input the preset ID.
1. Move the cursor to PRESET ID, and then tilt the
joystick left or right to toggle preset ID display on
and off.
5. Move the joystick left, right, up and down to adjust
the position of the lens focus, and then press the
CAM (SET) button.
Notes:
• Focusing may be difficult when the camera is at
an angle that is close to horizontal.
• A different position number can be selected by
moving the cursor to the position number at the
top of the position setting menu and tilting the
joystick left and right. Pressing the CAM (SET)
button will change to the setting screen for the
newly selected position number.
• The currently registered camera ID and preset ID
appear at the bottom of the position setting menu.
• When using a system device other than the WVCU650/CU950*, WJ-HD309A/HD316A over 65
position numbers cannot be set. (as of February 2005)
* Operation procedure may vary depending on
the version of the system controller’s software.
For Ver.1.xx or earlier: only camera function
operations are supported
For Ver.2.xx or later: PRESET/PGM PRESET
button is also supported
PRESET NO.
1*
POSITION SET
ON
PRESET ID
ALC
ALC/MANUAL
MANUAL L
AF MODE
10S
DWELL TIME
OFF
SCENE FILE
••••••••I
PRESET SPEED
L
H
RET TOP DEL
2. Select ON or OFF, and then press the CAM (SET)
button.
This will display the preset ID setting menu.
3. Use the joystick to move the cursor the character you
want to input, and then press the CAM (SET) button.
The text input procedure is the same as that for
camera ID input.
See steps 3 through 5 under “(1) Camera ID
(CAMERA ID)” on pages 22 for information about
inputting the text for the preset ID and specifying its
position on the display.
Align the cursor here
** POSITION 1* **
PAN/TILT
→PUSH SET
ZOOM/FOCUS
→PUSH SET
PAN OFFSET SET ←
0
→
RET TOP
FLOOR1
DOOR
-28-
WV-CS950 05.2.14 8:37 PM ページ29
(1) Selecting a Scene File
Use this procedure when you want to apply the
settings of a previously stored scene file when you are
configuring the settings of a preset position.
PRESET NO. 1*
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$
SPACE
COPY POSI RET RESET
PRESET NO.
1*
POSITION SET
ON
PRESET ID
ALC
ALC/MANUAL
MANUAL L
AF MODE
10S
DWELL TIME
1
SCENE FILE
••••••••I
PRESET SPEED
L
H
DOOR............
To copy the preset ID of another position number
Move the cursor to COPY, and then press the CAM
(SET) button. This displays the preset ID of the
position number preceding the one you are
currently configuring. Each press of the CAM (SET)
button scrolls back to the next sequential position
number and displays its preset ID.
RET TOP DEL
1. Move the cursor to SCENE FILE, and then tilt it left
and right to select the number of the scene file you
want to select.
● Light Control (ALC/MANUAL)
(2) Configuring Scene File Settings
1. Move the cursor to SCENE FILE, and then tilt it left
and right to select the number of the scene file
whose settings you want to configure.
See page 22 and 23 for information on the setting
method.
You can adjust the lens iris setting on the detailed
menu when MANUAL is set.
● Auto Focus (AF MODE)
**SCENE
SHUTTER
AGC
SENS UP
WHITE BAL
MOTION DET
1. Move the cursor to AF MODE, and then tilt the joystick
left or right to select an auto-focus function setting.
MANUAL S.M.L : Auto focus does not operate
after moving to a preset position.
AUTO S.M.L
: Auto focus operates after
moving to a preset position.
FILE 1**
OFF
ON(MID)
OFF
ATW1
OFF
RET TOP
2. Press the CAM (SET) button.
This will display the scene file setting menu.
The following items can be set on the Scene file
settings menu. See camera settings for details on
each setting.
• SHUTTER (page 23, 24)
• AGC (page 24)
• SENS UP (page 24)
• WHITE BAL (page 25)
• MOTION DET (page 36)
● Sequence/Sort DWELL Time (DWELL TIME)
This section explains how to set the length of time the
camera stops (time it stops rotating) and tapes the
scene while in the various preset positions for the
sequence and sort operations (page 30,31).
1. Move the cursor to DWELL TIME, and then tilt the
joystick left or right to select a DWELL time setting.
Tilting the joystick cycles through the stop time display
in the sequence shown below. (unit: sec, min)
2S ↔ 3S ↔ 5S ↔ 10S ↔ 30S ↔ 1MIN
● Preset Speed Setting (PRESET SPEED)
4MIN ↔ 3MIN ↔ 2MIN
Set the speed the camera moves to the various preset
positions for the sequence and sort operations (page
30, 31).
1. Move the cursor to PRESET SPEED, and then tilt the
joystick left or right to change the speed setting.
Shifting the setting towards the L side decreases the
speed, while shifting towards the H side increase it.
PRESET NO.
1*
POSITION SET
PRESET ID
ON
ALC/MANUAL
ALC
AF MODE
MANUAL L
DWELL TIME
10S
SCENE FILE
OFF
PRESET SPEED
••••••••I
L
H
RET TOP DEL
PRESET NO.
1*
POSITION SET
ON
PRESET ID
ALC
ALC/MANUAL
MANUAL L
AF MODE
10S
DWELL TIME
OFF
SCENE FILE
••••••••I
PRESET SPEED
L
H
● Scene File Setting (SCENE FILE)
Up to 10 scene files, each of which contains camera
settings for a specific location (scene), can be stored
in memory. Scene files are managed using scene file
numbers from 1 through 10, and can be selected when
configuring preset position settings.
The following procedures explain how to select a
scene file and how to configure scene file settings.
RET TOP DEL
-29-
WV-CS950 05.2.14 8:37 PM ページ30
● Deleting a Preset Position (DEL)
: In the auto mode, exits the auto mode
when the trigger time elapses.
AUTO (AUTO MODE setting not OFF) : Returns to
the auto mode when the trigger time
elapses.
AUTO (AUTO MODE setting OFF) : Returns to the
home position when the trigger time
elapses.
HOME
: Returns to the home position when the
trigger time elapses.
APAN
: Activates auto pan when the trigger
time elapses.
SEQ
: Activates the sequence function when
the trigger time elapses.
SORT
: Activates the sort function when the
trigger time elapses.
PTR 1 to 4 : Activates the patrol function when the
trigger time elapses.
TRK
: After the trigger time elapses, the
camera returns to the home position
and then automatic tracking starts.
Following that, after a set time, the
camera returns to the home position
and starts to continue automatic
tracking.
OFF
1. Move the cursor to DEL, and then press the CAM
(SET) button.
This deletes the contents of the currently selected
position number and displays the position selection
menu.
PRESET NO.
1*
POSITION SET
ON
PRESET ID
ALC
ALC/MANUAL
MANUAL L
AF MODE
10S
DWELL TIME
OFF
SCENE FILE
••••••••I
PRESET SPEED
L
H
RET TOP DEL
**PRESET POSITION**
1
2*
3*
4*
5*
8*
6*
7*
9*
10*
11*
12*
13*
16*
14*
15*
17*
18*
19*
20*
21*
24*
22*
23*
25*
26*
27*
28*
29*
32*
30*
31*
ID:DOOR
033-064 225-256
RET TOP
(3) Home Position Setting (HOME POSITION)
A currently configured preset position can be
designated as the home position.
Pressing the HOME button of the system controller will
cause the camera to move to the currently specified
home position. Use the following procedure to make a
preset position the home position.
1. Move the cursor to HOME POSITION, and then tilt
the joystick left or right to select the position
number of the preset position you want to make the
home position.
This causes the preset position whose position
number you select to become the home position. If
you do not want to use the home position function,
select OFF for the HOME POSITION setting.
Note: The HOME setting should be selected when
you want to normally leave the camera in the home
position and occasionally perform pan and tilt, or
when you want to activate SEQ.
(5) Auto Mode Setting (AUTO MODE)
Use the auto mode setting to specify the camera
movement mode (OFF, SEQ, SORT, AUTO PAN,
PATROL 1~4, AUTO TRACK).
After selecting AUTO PAN, you can use the AUTO PAN
setting menu to configure detailed settings.
1. Move the cursor to AUTO MODE, and then tilt the
joystick left or right to select a camera movement
mode setting.
OFF
: Manual movement only
SEQ
: Sequentially switches between
preset positions in position
number sequence. (sequential
movement)
SORT
: Sequentially switches between
preset positions counterclockwise,
starting from the camera home
position. (sort movement)
AUTO PAN
: Camera pans automatically within
the range specified by PAN.
Selecting AUTO PAN and pressing
the CAM (SET) button will display
the AUTO PAN setting menu,
which can be used for configuring
detailed settings. (page 31)
PATROL 1 to 4 : Operates the camera in accordance
with patrol function settings.
(4) Self Return Setting (SELF RETURN)
The self return setting can be used to specify automatic
return to a particular mode if a certain amount of time
elapses without any operation being performed.
1. Move the cursor to SELF RETURN, and then tilt the
joystick left or right to select a self return trigger setting.
Tilting the joystick cycles through the self return
display in the sequence shown below. (unit: sec,
min)
↔
30MIN
↔
50S
↔
↔
OFF ↔ 1S ↔ 2S ↔ 3S ↔ ....... ↔ 10S ↔ 20S ↔ 30S ↔ 40S
60MIN
↔
20MIN
↔
10MIN
↔
5MIN
↔
3MIN
↔
2MIN
↔
1MIN
2. If you selected any setting other than OFF in step 1,
press the CAM (SET) button and then tilt the
joystick left or right to select a self return mode.
OFF ↔ AUTO ↔ HOME ↔ APAN ↔ SEQ ↔ SORT
TRK ↔ PTR4 ↔ PTR3 ↔ PTR2 ↔ PTR1
-30-
WV-CS950 05.2.14 8:37 PM ページ31
AUTO TRACK : Auto tracking is done for moving
objects under the following
conditions.
The moving object must be larger
than one of the screen blocks
(1/48 of screen area), it must have
5 % comparative contrast with the
background image.
This defines the start point and moves the
cursor to POSITION.
**AUTO PAN**
POSITION
SPEED
ENDLESS
DWELL TIME
PAN LIMIT
START
END
••••I••••
L
H
OFF
1S
OFF
RET TOP
Notes:
• Automatic tracking covers a range from
horizontal to directly below the camera. The
digital flip function (page 34) does not operate.
Also, the pan range can be limited by using the
PAN LIMIT setting (this page).
The automatic tracking function incorporated in
this system easily tracks moving objects on
screen. Moving subjects are not automatically
tracked in the following situations.
• When multiple moving subjects are on screen
• When the subjects are moving very fast
• When the subject has little contrast
• When moving objects are either large or small
• When the image is dark
• When the image flickers
2. Move the cursor to SPEED and then tilt the joystick
left or right to select a panning speed setting.
Shifting the setting towards the “H” (right) side
increases the speed, while shifting towards the “L”
(left) side decreases it.
3. Move the cursor to ENDLESS, and then tilt the joystick
left or right to turn endless panning on or off.
ON : Pans from the start point to the end point,
and then continues to pan in the same
direction from the end point to the start point.
Select OFF for the PAN LIMIT setting (step 5)
when using this setting. Panning will be
repeated endlessly.
OFF : Pans from the start point to the end point,
and then reverses direction to pan from the
end point to the start point. Panning is
repeated endlessly.
4. Move the cursor to DWELL TIME, and then tilt the
joystick left or right to select the start point and end
point dwell time setting.
Tilting the joystick cycles through the stop time
display in the sequence shown below. (unit: sec)
Tilting the joystick cycles through settings in the
sequence shown below.
OFF ↔ SEQ ↔ SORT ↔ AUTO PAN ↔ PATROL1 ↔ PATROL2
AUTO TRACK ↔ PATROL4 ↔ PATROL3
Notes:
• The auto mode is exited automatically whenever
manual PAN/TILT or ZOOM/FOCUS is
performed if AUTO PAN is operating and
PAN/TILT does SEQ, SORT, PATROL, or AUTO
TRACK movement. Note, however, that that the
contents of the setting menu do not change. To
return to the auto mode, open the set-up menu
and then close it again. The auto mode will also
activate when the self return trigger time (page
30) elapses.
• During operation, the lens may enter the refresh
mode.
0S ↔ 1S ↔ 2S ↔ 3S ↔ 5S ↔ 10S ↔ 20S ↔ 30S
5. Move the cursor to PAN LIMIT, and then tilt the
joystick left or right to toggle it on and off.
ON : Limits manual panning to the zone between the
start point and the end point. The TILT range is
from 0° to 90°. Select OFF for the ENDLESS
setting (step 3) when using this setting.
OFF : Allows manual panning outside the zone
between the start point and the end point.
PAN LIMIT
PAN LIMIT allows panning in the area from the start
point to the end point specified in step 1, but not in the
area from the end point to the start point.
● Configuring AUTO PAN Detailed
Settings
1. Perform the following steps to set the PAN start
point and end point.
(1) Move the cursor to POSITION, press the CAM
(SET) button, and then move the cursor to
START.
(2) Use the joystick to move the camera to the
desired PAN start point, and then press the
CAM (SET) button.
This defines the start point and moves the
cursor to END.
(3) Use the joystick to move the camera to the
desired PAN end point, and then press the CAM
(SET) button.
End point
Camera
PAN LIMIT
zone
AUTO
PAN zone
Start point
Notes:
• When the panning, tilting, zooming or focusing
in the SEQ, SORT or PATROL mode is controlled
manually, the auto mode function should be
cancelled.
-31-
WV-CS950 05.2.14 8:37 PM ページ32
To activate the auto mode, select the desired
auto mode again or set a time for SELF RETURN
in the SET UP menu.
• When 0S is selected, the camera stops without
dwelling and starts.
• Auto refreshing may be activated during the patrol
play or the auto mode to calibrate the lens position.
3. Move the cursor to a PATROL number (PATROL 1
through 4), and then tilt the joystick left or right to
select a patrol setting.
--: Disables the selected patrol routine.
PLAY : Performs the selected patrol routine.
LEARN : Select this option to teach the camera a
series of movements (patrol routine). (An
asterisk (*) to the right of a PATROL
number indicates that it already has a
patrol routine assigned to it.)
DEL→PUSH SET : Press the CAM (SET) button to
delete an existing patrol routine.
4. Turn off the menu display with the F2 button on the
system controller, and activate the patrol function
set in step 3.
Turning on the system controller’s menu during a
LEARN operation causes the LEARN operation to
end. It also ends when the maximum storage time is
exceeded. Activate PLAY to check the stored
operations.
(6) AUTO PAN Key Setting (AUTO PAN KEY)
Set the operations of the camera when AUTO PAN is
executed from the system controller.
1. Move the cursor to AUTO PAN KEY, and then tilt the
joystick left or right to select a camera movement
mode setting.
Tilting the joystick cycles through settings in the
sequence shown below.
AUTO PAN ↔ SEQ ↔ SORT ↔ PATROL1 ↔ PATROL2
AUTO TRACK ↔ PATROL4 ↔ PATROL3
Note: Auto Mode can be started, but not stopped,
with the AUTO PAN key.
(7) Patrol Function Setting (PATROL)
The patrol function remembers manual operations for
later automatic playback when they are needed.
1. Aim the camera, with the menu closed, at the start
point of the routine you want it to remember.
2. Move the cursor to NUMBER, and then tilt the
joystick left or right to specify the number of patrol
routines.
Tilting the joystick cycles through settings in the
sequence shown below. The amount of storage
time available depends on the number of routines.
The storage time display changes in the sequence
shown below. (unit: sec, min)
1(2MIN) ↔ 2(1MIN) ↔ 4(30S)
Note that the total patrol time is two minutes, and
the time allowed for each routine depends on the
number of patrol routines that are configured. The
values in parentheses indicate the time of each
patrol routine (two minutes for one pattern, one
minute each for two patterns, 30 seconds each for
four patterns).
**PATROL**
NUMBER
PATROL1*
PATROL2
PATROL3
PATROL4
4(30S)
PLAY
-------
RESET
RET TOP
If you want to change the number of patrol routines
from a previous setting, first delete all of the
currently store patrol routines. To delete everything,
move the cursor to RESET, and press the CAM
(SET) button.
-32-
Notes:
• Selecting LEARN to teach the camera a patrol
routine causes the following parameters to be
stored along with the camera movements.
(1) Parameters at the Beginning of the Routine
• PAN, TILT, ZOOM, and FOCUS positions
• IRIS level
• Shutter speed (SHUTTER)
• Gain (AGC) setting
• Electronic sensitivity enhancement (SENS
UP) setting
• White balance (WHITE BAL) setting
• IMAGE HOLD
• AREA TITLE
• DIGITAL FLIP
• PRIVACY ZONE
• CAMERA ID
• PROPO.P/T
• PAN LIMIT
• ZOOM LIMIT
• TILT ANGLE
• BURST
• CLEANING
(2) During Camera Movement
• PAN, TILT, ZOOM, and FOCUS positions
• IRIS operation
• Preset positioning
• In the patrol play mode, the camera movement
may occasionally deviate from the entered
routine when the routine includes a move to a
preset position. If this happens, re-enter the
routine of manual operations for patrol-learn.
• In the patrol play mode, black and white
automatic switching does not work.
• In the patrol play mode, when the power of the
system controller is turned on or off, the patrol
play stops. In this case, press the PATROL PLAY
button again. (If SELF RETURN is set to ON, the
patrol play will start again after elapsing the
setting return time.)
WV-CS950 05.2.14 8:37 PM ページ33
6. Use the joystick to point the camera at the location to
be masked, and then press the CAM (SET) button.
This registers the camera position and returns to
the zone setting menu.
(8) Privacy Zone Setting (PRIVACY ZONE)
The privacy zone function makes it possible to mask
specific areas of the scene (screen) from view. Up to
eight privacy zones can be configured.
** ZONE NUMBER 3 /8**
PAN/TILT
→PUSH SET
→PUSH SET
ZOOM/FOCUS
Notes:
• Certain camera orientations can cause privacy
zone masked area to become visible.
• The privacy zone function does not mask scene
areas during the initialisation routine performed
immediately after camera power is turned on.
• The zone position may shift if the stabilizer settings
are change after setting the privacy zone.
U TILT D/L PAN R
ZONE SCALE
SET DEL
RET TOP
••••I••••
+
7. Move the cursor to →PUSH SET to the right of
ZOOM/FOCUS, and then press the CAM (SET) button.
This will display the ZOOM/FOCUS setting menu.
8. Move the joystick left, right, up and down to adjust
the position of the lens focus, and then press the
CAM (SET) button.
This completes the adjustment procedure and
returns to the zone setting menu.
Zoom can be set in a range of 1 to 10
magnifications.
1. Move the cursor to PRIVACY ZONE, and then tilt the
joystick left or right to select a privacy zone setting.
ON (1) : Turns on the privacy zone function.
ON (2) : Turns on the privacy zone function. (Mosaic)
OFF
: Turns off the privacy zone function.
Use the following steps to configure privacy zones.
2. Move the cursor to PRIVACY ZONE, and then press
the CAM (SET) button.
This will display the ZONE NUMBER selection menu.
The picture will be full wide angle (WIDE) if there is no
privacy zone defined for the current zone number.
**ZONE NUMBER 3 /8**
PAN/TILT
→PUSH SET
ZOOM/FOCUS
→PUSH SET
U ZOOM D/L FOCUS R
**ZONE NUMBER
1 /8**
ZONE SCALE
SET DEL
RET TOP
9. Move the cursor to ZONE SCALE, and then tilt the
joystick left or right to change the size of the zone
frame.
Shifting the setting towards the - side makes zone
frame smaller, while shifting towards the + side
makes it larger. Note, that the aspect ratio of the
zone frame is always 3:4. Also, the size of the zone
frame that can be set changes according to the
zoom ratio.
10. Move the cursor to SET, and then press the CAM
(SET) button.
This completes the privacy zone setting procedure
and returns to the zone number selection menu.
Selecting DEL instead of SET deletes the zone settings
and returns to the zone number selection menu.
RET TOP
3. Move the cursor to ZONE NUMBER, and then tilt
the joystick left or right to select the zone number (1
to 8) you want to configure.
An asterisk (*) to the right of the a number indicates
that it already has a privacy zone configured for it.
Selecting such a zone number zooms the picture to
the zoom setting that was in effect when its privacy
zone settings were configured.
4. Press the CAM (SET) button.
This will display the zone setting menu. The
appearance of the menu depends on zone settings.
**ZONE NUMBER 3 /8**
PAN/TILT
→PUSH SET
ZOOM/FOCUS
→PUSH SET
(9) Image Hold Setting (IMAGE HOLD)
Image hold causes the current picture to be frozen until
the camera finishes moving to a preset position. This
function comes in handy when using a network interface
unit for monitoring of camera images over a network.
1. Move the cursor to IMAGE HOLD, and then tilt the
joystick left or right to toggle it on and off.
ON : Maintains the last image until the camera
finishes moving to a preset position.
However, the still image may be distorted
with the effect of panning or tilting.
OFF : Picture being picked up by the camera
continues to be displayed as the camera
moves to a preset position.
Zone frame
ZONE SCALE
SET DEL
RET TOP
••••I••••
+
••••I••••
+
The currently configured zone frame will appear in
the centre of the picture.
Performing the remaining steps of this procedure
will delete the current zone frame and replace it
with the new zone frame that you configure.
5. Move the cursor to →PUSH SET to the right of
PAN/TILT, and then press the CAM (SET) button.
This will display the PAN/TILT setting menu.
-33-
WV-CS950 05.2.14 8:37 PM ページ34
(10) Digital Flip Setting (DIGITAL FLIP)
Normally, a camera needs to stop when it points
straight down during tilt. With digital flip, however, the
camera is able to tilt from 0° to 180° in a single motion.
This makes it possible to track objects passing directly
under the camera more smoothly. The picture is
flipped vertically and horizontally when the camera is
at an angle of around 135°.
1. Move the cursor to DIGITAL FLIP, and then tilt the
joystick left or right to toggle it on and off.
ON : Turns on digital flip. Note that the tilt range
becomes 0° to 90° when ON is selected for
the PAN LIMIT setting.
OFF : Turns off digital flip. With this setting, the tilt
range is 0° to 90°.
ON (NESW) : Displays direction indicators.
Selecting ON (NESW) and pressing
the CAM (SET) button will display the
position (NESW) setting menu, which
you can use for configuring detailed
settings. (this page)
ON (USER) : Displays user input text.
Selecting ON (USER) and pressing
the CAM (SET) button will display the
area title (USER) selection menu,
which you can use for configuring
detailed settings. (page 35)
OFF
: Turns off display of area title
direction indicators and text.
(1) When ON (NESW) is selected
After selecting ON (NESW), you can use the position
(NESW) setting menu to configure detailed settings.
Once you set the northerly (N) direction for the camera,
all other directions are displayed automatically.
1. Move the cursor to →PUSH SET to the right of
PAN/TILT, and then press the CAM (SET) button.
This will display the PAN/TILT setting menu.
Notes:
• Digital flip is performed when the joystick is held
straight downwards only. It is not performed
when the joystick is tilted in any other direction.
• When OFF is selected for DIGITAL FLIP, the
following steps need to be performed in order to
tilt the camera 180°.
(1) Tilt the joystick downwards to point the
camera straight down.
(2) Tilt the joystick left or right to pan the camera
180°.
(3) Tilt the joystick upwards.
• Momentarily turn off DIGITAL FLIP and set the
zoom limit to 30x magnification or less before
setting a preset position directly from the WVCU360C System Controller. You can turn these
functions back on again after setting the preset
position.
Note that digital flip cannot be specified for the
90° to 180° tilt range.
**DIRECTION(NESW)**
PAN/TILT
→PUSH SET
→PUSH SET
ZOOM/FOCUS
POSI
+
N
RET TOP
2. Use the joystick to point the camera north, and then
press the CAM (SET) button.
**DIRECTION(NESW)**
→PUSH SET
PAN/TILT
→PUSH SET
ZOOM/FOCUS
POSI
U TILT D/L PAN R
+
N
(11) Proportional Pan/Tilt Setting (PROPO. P/T)
This function optimizes the image by automatically
adjusting the PAN/TILT (horizontal/vertical rotation)
speed according to the zoom ratio.
1. Move the cursor to PROPO.P/T, and then tilt the
joystick left or right to toggle it on and off.
ON : Pan/tilt speed is in inverse proportion to the
zoom ratio.
OFF : The speed is constant at the fastest level
regardless of the zoom ratio.
RET TOP
3. Move the cursor to →PUSH SET to the right of
ZOOM/FOCUS, and then press the CAM (SET) button.
This will display the ZOOM/FOCUS setting menu.
4. Move the joystick left, right, up and down to adjust
the position of the lens focus, and then press the
CAM (SET) button.
(12) Area Title Setting (AREA TITLE)
The area title function lets you display a direction
indicator that appears in the picture to indicate the
direction of the location being shown on the screen.
Text can also be displayed in place of the direction
indicators, if desired.
The direction indicators are N (north), NE (northeast), E
(east), SE (southeast), S (south), SW (southwest), W
(west), and NW (northwest).
1. Move the cursor to AREA TITLE, and then tilt the
joystick left or right to turn the area title display
function on or off.
**DIRECTION(NESW)**
PAN/TILT
→PUSH SET
ZOOM/FOCUS
→PUSH SET
POSI
U ZOOM D/L FOCUS R
+
N
RET TOP
5. Move the cursor to POSI O, and then press the
CAM (SET) button.
This will display the ID position setting menu.
-34-
WV-CS950 05.2.14 8:37 PM ページ35
In the example screen shown in step 1, NORTH O
is the title name of area title number 1.
4. Input an area title.
The text input procedure is the same as that for
camera ID input.
See steps 3 through 5 under “(1) Camera ID
(CAMERA ID)” on page 22 for information about
inputting the text for the area title and specifying its
position on the display.
6. Use the joystick to select an area title display
position, and then press the MON (ESC) button.
This registers the area title display position and
returns to the area title (NESW) setting menu.
AREA TITLE 1
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$
FLOOR 1
N
Note: The area title is always displayed under the
camera ID. If you specify different display position
settings for the camera ID and the area title ID, the
area title ID display position setting is used for both.
SPACE
---- POSI RET RESET
................
(2) When ON (USER) is selected
After selecting ON (USER), you can use the area title
(USER) setting menu to configure detailed settings.
You can use the following procedure to configure
direction settings, and to input text associated with a
particular direction indicator.
1. Move the cursor to 1, and then press the CAM
(SET) button.
This will display the position setting menu. An asterisk
(*) to the right of an area title number indicates that it
already has an area title assigned to it.
If the there is already text associated with the
direction you selected, it will appear under the
cross mark (+). If there is no text associated with
the direction, only the cross mark (+) will be
displayed.
FLOOR 1
NORTH
5. Repeat steps 1 through 4 for the other area
numbers, if you want.
(13) Tilt Angle Setting (TILT ANGLE)
Selecting 5° for the TILT ANGLE setting allows tilting
past horizontal, in the range of -5° to 185°.
1. Move the cursor to TILT ANGLE, and then tilt the
joystick left or right to toggle the setting between 0°
and 5°.
**AREA TITLE(USER)**
1*
NORTH
2
3
4
5
6
7
8
Notes:
• Zooming to WIDE while 5° is selected for the
TILT angle setting will cause the upper half of
the picture to become hidden.
• With certain subjects, AGC (gain control) can
cause the image to become white.
RET TOP RESET
(14) Cleaning Settings (CLEANING)
This camera uses a "slip ring" for transmission of
electrical power and signals. A dirty slip ring can cause
deterioration of picture quality and generation of noise.
The cleaning function performs cleaning approximately
once a week to keep the slip ring clean.
1. Move the cursor to CLEANING, and then tilt the
joystick left or right to toggle it on and off.
The text CLEANING appears in the centre of the
screen while the cleaning process is being
performed.
2. Adjust the camera orientation (pan and tilt), zoom,
and focus.
Perform steps 1 through 4 under “(1) When ON
(NESW) is selected” on page 34.
**DIRECTION(USER) 1**
PAN/TILT
→PUSH SET
ZOOM/FOCUS
→PUSH SET
+
NORTH
RET TOP DEL
Note: Select OFF for CLEANING before performing
an upload or download data with a system device.
This protects against the download or upload failure
due to start up of the cleaning process.
3. Move the joystick to the right to align the cursor with
the title display, and press the CAM (SET) button.
This will display the area title setting menu.
-35-
WV-CS950 05.2.14 8:37 PM ページ36
ALARM SETTINGS
■ Using the Alarm Set-up Menu
**MODE1**
LEVEL
Display the alarm set-up menu from the setup menu to
configure alarm settings.
First, display the alarm set-up menu.
1. Display the set-up menu (page 21), move the cursor
to ALARM O, and then press the CAM (SET) button.
DWELL TIME
DISPLAY MODE
ALARM
MASK SET
RECOVER TIME
••••I••••
+
2S
OFF
OFF
RET TOP
**ALARM SETUP**
MOTION DET
OFF
PRESET ALM
OFF
ALARM IN/OUT
q
e
2. Mask the areas of the screen that you do not want
the motion detector to monitor for movement.
To mask screen areas, use the same procedure as
step 3 under "SUPER-D 3 (Super Dynamic 3)" on
page 23. After configuring mask settings, press the
MON (ESC) button to return to the motion detector
setting menu.
3. Move the cursor to ALARM, and then tilt the joystick
left or right to toggle demo mode (see step 5) alarm
output on and off.
ON : Turns on alarm output in the demo mode.
OFF : Turns off alarm output in the demo mode.
4. Move the cursor to DISPLAY MODE, and then press
the CAM (SET) button.
This activates the demo mode.
w
RET TOP
This will display the alarm set-up menu.
* The following sections numbered q to e explain
how to use each of the alarm set-up menu items.
(1) Motion Detector Setting (MOTION DET)
1. Move the cursor to MOTION DET, and then tilt the
joystick left or right to toggle it on and off.
OFF
:Turns off the motion detector.
MODE 1 :Alarm signal is output when motion is
detected in the image. Selecting MODE 1
and pressing the CAM (SET) button displays
the mode 1 setting menu, which can be
used for configuring detailed settings.
MODE 2 :Alarm signal is output when the camera is
covered by cloth, a lid, spray paint or
something.
Demo Mode
The demo mode divides the screen into 48 blocks and
monitors changes in the luminance in each block. It
also masks any part of the picture where there is a
change in average luminance that exceeds the
currently specified detection sensitivity level. The demo
mode results can be used to determine the optimum
detection sensitivity level (step 5) and the areas of the
screen that need to be masked (step 1).
5. Move the cursor to LEVEL, and then tilt the joystick
left or right to set the detection sensitivity level.
Shifting the setting towards the + side increases
sensitivity, while shifting towards the - side
decreases it. Repeat steps 4 and 5 until the
optimum sensitivity level is obtained.
Motion Detector
The motion detector divides the screen into 48 blocks
and monitors changes in the luminance in each block.
When it detects any change (movement) in the image,
it outputs an alarm signal. When a change (movement)
in the image is detected while in the auto mode, the
alarm signal is output and the camera stops at the
preset position for a specified amount of time.
Detection Conditions
Object Size
: The moving object must be larger
than one of the screen blocks (1/48
of the total screen area).
Subject Contrast: The contrast ratio between the
background and the moving object
must be at least 5 % (at the
maximum LEVEL setting).
Object Speed
: The allowable time range for the
object to pass from one edge of the
screen to the other is 0.1 second to
0.8 second. Movement that is faster or
slower than this cannot be detected.
Important
: Size and speed limitations are
relaxed somewhat when the contrast
ratio between the background and
the moving object is large.
Important! Conditions for Mode 2
Monitoring might not be possible in the following
situations.
• If only one part of the screen is not covered, or if
the covering is translucent
Also, false detection might occur in the following
situations.
• When extreme changes in lighting occur, such as
turning lights on an off
• If pedestrian or vehicle traffic is heavy
● Configuring Detailed Motion Detector
Settings for MODE 1
1. Move the cursor to MASK SET O, and then press
the CAM (SET) button.
This will display the mask setting screen.
-36-
WV-CS950 05.2.14 8:37 PM ページ37
6. Move the cursor to DWELL TIME, and then tilt the
joystick left or right to select an alarm detect dwell
time setting.
After alarm detection, the next alarm is not detected
until the specified dwell time elapses.
Tilting the joystick cycles through the setting
display in the sequence shown below. (unit: sec)
• When the self return function is activated (page 30)
and the camera finishes moving to the home
position, and when switching to the auto mode.
• When SEQ is selected for the auto mode (page 30),
and the camera completes a move to a preset
position during sequential movement
• When SORT is selected for the auto mode (page
30), and the camera completes a move to a preset
position during SORT movement
• When AUTO PAN is selected for the auto mode
(page 30), and the camera completes a preset
move up to the AUTO PAN start point
• When the camera completes a move to a preset
position during manual operation
• When PLAY is selected for the auto mode (page
32), and the camera completes a preset move up to
the patrol start point
Use the following procedures to configure preset alarm
settings
1. Move the cursor to PRESET ALM, and then tilt the
joystick left or right to toggle it on and off.
ON : Turns on the preset alarm function.
OFF : Turns off the preset alarm function.
2S ↔ 5S ↔ 10S ↔ 30S
7. Move the cursor to RECOVER TIME, and then tilt
the joystick left or right to select an alarm reset time
setting.
Tilting the joystick cycles through the setting display
in the sequence shown below. (unit: sec, min)
If you set OFF, then it does not reset until some
other operation is done. If AUTO TRACK is set, the
camera starts automatic tracking when change
(movement) is detected in the image during SEQ or
SORT.
OFF ↔ 1MIN ↔ 2MIN ↔ 3MIN ↔ 5MIN ↔ 10MIN
AUTO TRACK ↔ 60MIN ↔ 30MIN ↔ 20MIN
Notes:
• Monitoring is usually done in SEQ mode, and
when the camera detects change (movement)
automatic tracking starts. To have the camera
return to SEQ mode after a certain amount of
time, set the SELF RETURN setting to SEQ.
• Use the mask setting to mask areas where there
is wind movement of curtains, etc.
• Use a lower sensitivity level (LEVEL) setting for
areas where illumination is low and prone to
digital noise. Also note that operation error can
occur when the illuminance of a subject is
changed suddenly by the headlights of passing
cars, turning lights on or off, etc.
• There is a delay of about 0.2 second from the
point that the camera detects change
(movement) in the image and the point that a
signal is sent to the alarm terminal of a VCR, etc.
• Alarms are not output while the setting menu is
displayed, unless demo mode alarm output is
turned on.
• Alarms are not output when PAN, TILT, ZOOM,
FOCUS or other functions are operating.
• When the motion detector is set to MODE 1 or
MODE 2, it outputs alarm data during the
blanking period. This can cause operational
problems for a VCR or other device that uses a
time code signal, etc. Turn off the motion
detector when not using coaxial communication.
• The motion detector is not intended for use as
specialty device for the prevention of theft, fire,
etc. The manufacturer assumes no responsibility
for any accidents that occur or any losses
incurred while this product is being used.
Note: Turn off the preset alarm function before
downloading or uploading preset data.
(3) Alarm Input/Output (ALARM IN/OUT)
Use this setting to specify what operation the camera
should perform when it an alarm signal is input to the alarm
input connector or output from the alarm output connector.
Note: While the camera is in the AF mode or the
lens moves between WIDE and TELE, alarm input
may be ignored if several alarm inputs are received
in succession.
1. Move the cursor to the ALARM IN/OUT O and then
press the CAM (SET) button.
This will display the alarm setting menu.
2. Move the cursor to ALARM IN 1, and then tilt the
joystick left and right to select the operation the
camera should perform when an external signal is
received by ALARM IN 1.
OFF
: Ignore alarm input signals.
1POSI
: Move to preset position 1.
AUTOPAN
: Start auto pan.
PATROL1
: Start PATROL 1.
PATROL1 (S) : Start PATROL 1, and maintain the
stored picture quality settings
(page 32) even after completion.
AUTOTRACK1 : Move to preset position number 1,
and then perform auto tracking.
**ALARM IN/OUT**
ALARM IN1
OFF
ALARM IN2
OFF
ALARM IN3
OFF
ALARM IN4
OFF
CNT-CLS 1
TIME OUT
CNT-CLS 2
COAX ALM OUT
(2) Preset Alarm Setting (PRESET ALM)
Turning on the preset alarm will output an alarm from
the video output port or alarm output connector when
the camera completes a move to a preset position. An
alarm is output in the following cases.
RET TOP
-37-
OFF
100MS
OFF
OFF
WV-CS950 05.2.14 8:37 PM ページ38
6. Move the cursor to CNT-CLS 1, and then tilt the
joystick left and right to select the alarm output that
should be performed over ALARM OUT 1 when an
alarm is detected.
OFF
: No alarm output
ALARM : Output an alarm signal when an alarm is
detected by the motion detector (page 36)
or the preset alarm (page 37). After
selecting this setting, perform step 7 to
specify the alarm signal output time.
AUX1
: Output a contact close signal when
AUX1 input is received from the system
controller.
7. If you selected ALARM in step 6, move the cursor to
TIME OUT and then tilt the joystick left and right to
select the alarm signal output time.
Tilting the joystick cycles through the output time
display in the sequence shown below. (unit: ms)
3. Move the cursor to ALARM IN 2, and then tilt the
joystick left and right to select the operation the
camera should perform when an external signal is
received by ALARM IN 2.
OFF
: Ignore alarm input signals.
2POSI
: Move to preset position 2.
SEQ
: Start sequential movement.
PATROL2
: Start PATROL 2.
PATROL2 (S) : Start PATROL 2, and maintain the
stored picture quality settings
(page 32) even after completion.
AUTOTRACK2 : Move to preset position number 2,
and then perform auto tracking.
4. Move the cursor to ALARM IN 3, and then tilt the
joystick left and right to select the operation the
camera should perform when an external signal is
received by ALARM IN 3.
OFF
: Ignore alarm input signals.
3POSI
: Move to preset position 3.
SORT
: Start sort movement.
PATROL3
: Start PATROL 3.
PATROL3 (S) : Start PATROL 3, and maintain the
stored picture quality settings
(page 32) even after completion.
AUTOTRACK3 : Move to preset position number 3,
and then perform auto tracking.
100 MS ↔ 200 MS ↔ 1000 MS ↔ 2000 MS ↔ 4000 MS
Note: The shorter the duration, the more
frequent will be the detection output.
8. Move the cursor to CNT-CLS 2, and then tilt the
joystick left and right to select the alarm output that
should be performed from ALARM OUT 2 when an
alarm is detected.
OFF
: No alarm output
BW
: Output a contact close signal only while
the camera is in the black and white
mode.
AUX2
: Output a contact close signal when
AUX2 input is received from the system
controller.
5. Move the cursor to ALARM IN 4, and then tilt the
joystick left and right to select the operation the
camera should perform when an external signal is
received by ALARM IN 4.
OFF
: Ignore alarm input signals.
4POSI
: Move to preset position 4.
BW
: Black and white display while
signal is being input.
PATROL4
: Start PATROL 4.
PATROL4 (S) : Start PATROL 4, and maintain the
stored picture quality settings
(page 32) even after completion.
AUTOTRACK4 : Move to preset position number 4,
and then perform auto tracking.
Note: It is recommended to set the connected
external device to ignore the shorter alarm outputs
of 90 ms or less from the camera.
9. Move the cursor to COAX ALM OUT, and then tilt
the joystick left or right to toggle it on and off.
This setting turns alarm controls whether an alarm is
output when the camera moves to one of the preset
positions specified for ALARM IN 1 through 4 (1POSI,
2POSI, 3POSI, 4POSI) in steps 2 through 5, above.
ON
: Output an alarm signal from the video
output connector at the point the camera
finishes moving to a preset position
(number 1 through 4) when there is alarm
input to ALARM IN (1 through 4).
OFF
: No alarm signal output
Notes:
• Use PATROL 1 (S) to 4 (S) if you want to switch
picture quality (for example to switch picture
quality from day to night) when an alarm input is
received. ALARM IN4 can be used combined
with BW.
To use the camera with this application, set the
picture quality you want to switch before
registering the patrol, then start the patrol
registration and then end the registration
immediately.
• If you want to change the picture quality settings
according to alarm input for PATROL 1 (S) to 4
(S), the settings are applied to the camera
settings and are kept even after the camera is
turned on again.
Notes:
• The camera ignores alarm inputs during manual
operation.
• Turn off alarm outputs before downloading or
uploading preset data.
-38-
WV-CS950 05.2.14 8:37 PM ページ39
SPECIAL SETTINGS
■ Using the Special Set-up Menu
Display the special set-up menu from the set-up menu
to adjust picture quality.
First, display the special set-up menu.
1. Display the set-up menu (page 21), move the cursor
to SPECIAL O, and then press the CAM (SET)
button.
This will display the special set-up menu.
To delete a blemish compensation pattern
(1) On the PIX OFF menu screen, select of the
pattern you want to delete, and press the CAM
(SET) button.
This will display the blemish compensation
pattern setting screen.
(2) On the WV-CU650C, press the F3 button.
(3) This returns to the PIX OFF menu.
This will delete the blemish compensation
pattern and remove the asterisk (*) to the right of
the applicable pattern number.
6. To correct for camera deviation from the preset
positions during operation, move the cursor to
→PUSH SET to the right of REFRESH, and then
press the F2 button.
The refresh function corrects the camera position
when it starts to deviate from the preset positions. If
you are not using the WV-CU650C system
controller, perform one of the following steps to
correct the camera position.
7. To reset the camera to its initial default settings,
move the cursor to →PUSH SET to the right of
CAMERA RESET, and then press the F4 button.
This resets the camera to it initial factory default
settings. Note, however, that this does not change
the camera's preset position, AUTO PAN, patrol,
RS485, blemish compensation patter and password
settings.
If you are not using the WV-CU650C system controller,
perform one of the following steps to reset the camera.
**SPECIAL SETUP**
CHROMA GAIN
••••I••••
•••I•••••
AP GAIN
PEDESTAL
••I••••••
••••I••••
HUE
+
PIX OFF
→PUSH SET
REFRESH
CAMERA RESET →PUSH SET
SER.NO. BFB03964
RET TOP
● Adjusting Picture Quality
Use the following procedure to adjust picture quality.
1. Move the cursor to CHROMA GAIN, and then tilt the
joystick left or right to adjust the CHROMA GAIN level.
2. Move the cursor to AP GAIN, and then tilt the
joystick left or right to adjust the aperture level.
3. Move the cursor to PEDESTAL, and then tilt the
joystick left or right to adjust the PEDESTAL level.
4. Move the cursor to PIX OFF O, and then press the
CAM (SET) button.
This will display the PIX OFF menu. Perform the
following steps to perform blemish compensation
on the pixels.
5. Select a position that has a blemish with the PIX
OFF number, and then press the CAM (SET) button.
This will display the blemish compensation pattern
setting screen.
(1) Use the joystick to move the cross cursor ( ) to
the location of the defective pixels.
(2) Move the cursor around the display until there
are no more white spots (blemishes) visible, and
then press the CAM (SET) button.
This will store the blemish compensation pattern.
(3) This returns to the PIX OFF menu.
An asterisk (*) to the right of a PIX OFF number
indicates that the number has a blemish
compensation pattern assigned to it.
1*
5*
9
13
Note: If above operations are performed while the
cursor is located at any other item besides
CAMERA RESET, further menu operations may
become impossible. If this happens, use the
procedure under "Displaying the Set-up Menu" on
page 21 to re-display the menu.
** PIX OFF **
2*
3*
4*
6*
7*
8
10
11
12
14
15
16
000 000
RET TOP
-39-
WV-CS950 05.2.14 8:37 PM ページ40
SCENE SELECT SETTING
■ Using the Scene Select Setting
Menu
Display the scene select setting menu from the set-up
menu to configure scene select settings. First, display
the scene select setting menu.
1. Display the set-up menu (page 21), move the
cursor to SCENE SELECT O, and then press the
CAM (SET) button.
This will display the scene select setting menu.
**SCENE SELECT**
SCENE
INDOOR(L)
LOAD
RET TOP
● Scene Select Settings
Use the following procedure to configure scene select
settings.
1. Move the cursor to SCENE, and then tilt the joystick
left or right to change the scene setup.
INDOOR (L)
: Indoor setting (picture quality
priority)
INDOOR (H)
: Indoor
setting
(sensitivity
priority)
OUTDOOR (L)
: Outdoor
setting
(picture
quality priority)
OUTDOOR (H)
: Outdoor setting (sensitivity
priority)
Settings related to the picture switch depending on
the scene settings. Scene select settings and
relationship to other settings are shown in the table
below.
AGC
SENS UP
SHUTTER
BW
DNR
WHITE BAL
INDOOR (L)
MID
OFF
OFF
OFF
LOW
ATW1
INDOOR (H)
HIGH
×2 AUTO
OFF
OFF
HIGH
ATW1
OUTDOOR (L)
MID
OFF
AUTO
AUTO LOW
ATW2
×2 AUTO
AUTO
AUTO HIGH
ATW2
OUTDOOR (H) HIGH
2. Move the cursor to LOAD, and then press the CAM
(SET) button.
This will cause the set-up you selected for SCENE
in step 1 to be applied to the image.
-40-
WV-CS950 05.2.14 8:37 PM ページ41
QUICK MENU SETTINGS
■ Displaying the Quick Set-up Menu
The quick set-up menu can be displayed from the setup menu.
1. Display the set-up menu (page 21), move the
cursor to → QUICK SET-UP, and then press the
CAM (SET) button.
Only the following items can be set on the quick
setup menu.
• Camera ID setting (page 22)
• Scene select settings (page 40)
• Preset position settings (page 27)
• Language settings (page 21)
MODEL
WV-CS950 SERIES
CAMERA ID
OFF
SCENE SELECT
PRESET POSITION
LANGUAGE
→ADVANCED SETUP
The procedures for configuring settings using the
quick set-up menu are the same as those for the
detailed menu.
To switch back to the detailed menu from the quick
set-up menu, move the cursor to →ADVANCED SET
UP, and then press the CAM (SET) button.
-41-
WV-CS950 05.2.14 8:37 PM ページ42
PASSWORD SETTINGS
■ Password Lock Settings
4. Press the CAM (SET) button.
This returns to the set-up menu and toggles
PASSWORD LOCK on or off.
The password input screen will reappear if you
press the CAM (SET) button after inputting the
wrong password. If this happens, perform steps 2
and 3 again.
Set the password lock on the set-up menu.
● Turning Password Lock On and Off
The password lock function can be used to allow only
authorized personnel to change camera settings. A
password must be input in order to turn password lock
on or off.
ON : Prohibits changing any settings except for
the password lock function.
Selecting
this
setting
limits
camera
configuration changes to authorized personnel.
OFF : Settings on all menus can be changed.
If you are using a VCR for recording, turn off recording
before inputting the password. Inputting the password
while the picture is being recorded by a VCR will cause
the password to be recorded with the picture.
1. Display the set-up menu (page 21), move the
cursor to PASSWORD LOCK (ON or OFF), and then
press the CAM (SET) button.
This will display the password input menu.
● Changing the Password
After turning on password lock, it is recommended that
you use the following procedure to change the factory
default password to a different one. Also, make sure
you keep a separate record of your password so you
do not forget it.
If you are using a VCR for recording, turn off recording
before inputting the password. Inputting the password
while the picture is being recorded by a VCR will cause
the password to be recorded with the picture.
1. Display the set-up menu (page 21), move the
cursor to PASSWORD LOCK (ON or OFF), and then
press the CAM (SET) button.
This will display the password input menu.
MODEL
WV-CS950 SERIES
CAMERA
PAN/TILT
ALARM
SPECIAL
COMMUNICATION
SCENE SELECT
LANGUAGE
MODEL
WV-CS950 SERIES
CAMERA
PAN/TILT
ALARM
SPECIAL
COMMUNICATION
SCENE SELECT
LANGUAGE
→QUICK SETUP
PASSWORD LOCK OFF
→QUICK SETUP
PASSWORD LOCK OFF
2. To set the password for the first time, enter the
factory default password "123" and then press the
CAM (SET) button.
2. Input the current 3-digit password by moving the
cursor to each of the applicable numbers along the
top of the screen (0 to 9) and pressing the CAM
(SET) button for each digit.
The ↑ pointer will move to the right each time you
input a digit. After you input all three digits, move
the cursor to OK.
If you make a mistake during input, move the cursor
to RESET, press the CAM (SET) button, and then reinput the entire password.
Note: You must use this procedure. The password
Lock ON/OFF does not switch.
3. Input a 3-digit password by moving the cursor to
each of the applicable numbers along the top of the
screen (0 to 9) and pressing the CAM (SET) button
for each digit.
** PASSWORD? **
0 1 2 3 4 5 6 7 8 9
** PASSWORD? **
. . .
0 1 2 3 4 5 6 7 8 9
. . .
OK RESET
NEW PASSWORD
RET TOP
OK RESET
NEW PASSWORD
RET TOP
The ↑ pointer will move to the right each time you
input a digit. After you input all three digits, move
the cursor to OK.
If you make a mistake during input, move the cursor
to RESET, press the CAM (SET) button, and then reinput the entire password.
Note: The factory default password is 123.
-42-
WV-CS950 05.2.14 8:37 PM ページ43
3. Move the cursor to NEW PASSWORD and press the
CAM (SET) button to display the password setting
menu.
The password input screen will reappear if you
press the CAM (SET) button after inputting the
wrong password. If this happens, perform steps 2
and 3 again.
4. Input the new 3-digit password by moving the
cursor to each of the applicable numbers along the
top of the screen (0 to 9) and pressing the CAM
(SET) button for each digit.
After you input all three digits, move the cursor to
OK.
** NEW PASSWORD? **
0 1 2 3 4 5 6 7 8 9
. . .
. . .
OK
RESET
RET TOP
5. Press the CAM (SET) button.
This returns to the new password input screen
again for verification.
Note that you cannot register the new password by
pressing the MON (ESC) button.
6. Input the new 3-digit password again by moving the
cursor to each of the applicable numbers along the
top of the screen (0 to 9) and pressing the CAM
(SET) button for each digit.
After you input all three digits, move the cursor to
OK.
7. Press the CAM (SET) button.
This completes the password change operation
and returns to the setup menu. If the new password
you input in step 6 is different from the one you
input in step 4, the new password input screen will
appear again. If this happens, perform steps 4
through 7 again. Note that you cannot register the
new password by pressing the MON (ESC) button.
-43-
WV-CS950 05.2.14 8:37 PM ページ44
SHORTCUTS
Shortcuts are supported when you are using the system controller that has a CAM FUNCTION button. With shortcuts,
you can configure camera functions by inputting function codes on the 10-key pad and then pressing the CAM
FUNCTION button.
The following is a list of all of the shortcuts that are supported by this camera. In addition, you can also move the
camera to a preset position by inputting the applicable position number on the 10-key pad.
Notes:
• Turn off digital flip before registering preset positions. If NO REGS.; FLIP ON appears, do the setting again.
• Shortcuts may not be performed if they are executed while a pan, tilt, zoom, or focus operation is in progress.
• Shortcuts 1 through 64, 169, 170, and 301~556 can be saved as part of a patrol routine.
• Except for shortcuts 169 and 170, executing any shortcut during patrol routine PLAY will cause the PLAY
operation to stop.
Controller Operation
Setting
[6] + [5] + [CAM FUNCTION]
AUTO PAN ON
[6] + [6] + [CAM FUNCTION]
AUTO PAN OFF
[6] + [7] + [CAM FUNCTION]
Increases AUTO PAN speed one step.
[6] + [8] + [CAM FUNCTION]
Decreases AUTO PAN speed one step.
[6] + [9] + [CAM FUNCTION]
Sets AUTO PAN start point.
[7] + [0] + [CAM FUNCTION]
Sets AUTO PAN end point.
[7] + [1] + [CAM FUNCTION]
AUTO MODE: OFF
[7] + [2] + [CAM FUNCTION]
AUTO MODE SEQ: OFF
[7] + [3] + [CAM FUNCTION]
AUTO MODE SEQ: SORT ON
[7] + [4] + [CAM FUNCTION]
Reverses AUTO PAN range.
[7] + [6] + [CAM FUNCTION]
ENDLESS: ON
[7] + [7] + [CAM FUNCTION]
ENDLESS: OFF
[7] + [8] + [CAM FUNCTION]
DIGITAL FLIP: ON
[7] + [9] + [CAM FUNCTION]
DIGITAL FLIP: OFF
[8] + [0] + [CAM FUNCTION]
PROPO.P/T: ON
[8] + [1] + [CAM FUNCTION]
PROPO.P/T: OFF
[8] + [4] + [CAM FUNCTION]
SUPER-D 3: ON
[8] + [5] + [CAM FUNCTION]
SUPER-D 3: OFF
[8] + [6] + [CAM FUNCTION]
AF MODE: AUTO
[8] + [7] + [CAM FUNCTION]
AF MODE: MANUAL
[8] + [8] + [CAM FUNCTION]
Performs auto focus.
[8] + [9] + [CAM FUNCTION]
Moves to home position.
[9] + [0] + [CAM FUNCTION]
BW: ON
[9] + [1] + [CAM FUNCTION]
BW: OFF
[9] + [2] + [CAM FUNCTION]
BW: AUTO
[9] + [3] + [CAM FUNCTION]
CAMERA ID: ON
[9] + [4] + [CAM FUNCTION]
CAMERA ID: OFF
[9] + [5] + [CAM FUNCTION]
AREA TITLE: ON (NESW)
[9] + [6] + [CAM FUNCTION]
AREA TITLE: ON (USER)
[9] + [7] + [CAM FUNCTION]
AREA TITLE: OFF
[1] + [0] + [0] + [CAM FUNCTION]
Adjusts camera position (REFRESH)
[1] + [0] + [1] + [CAM FUNCTION]∼
Stores preset to first available preset number (1 to 64).
[1] + [6] + [4] + [CAM FUNCTION]
[1] + [6] + [5] + [CAM FUNCTION]
PATROL1: PLAY
[1] + [6] + [6] + [CAM FUNCTION]
PATROL 1 - PATROL 4: STOP
[1] + [6] + [7] + [CAM FUNCTION]
PATROL1: LEARN start
[1] + [6] + [9] + [CAM FUNCTION]
IRIS: OPEN
-44-
WV-CS950 05.2.14 8:37 PM ページ45
Controller Operation
Setting
[1] + [7] + [0] + [CAM FUNCTION]
IRIS: CLOSE
[1] + [7] + [1] + [CAM FUNCTION]
SHUTTER: ON
[1] + [7] + [2] + [CAM FUNCTION]
SHUTTER: OFF
[1] + [7] + [3] + [CAM FUNCTION]
Increases shutter speed one step.
[1] + [7] + [4] + [CAM FUNCTION]
Decreases shutter speed one step.
[1] + [7] + [5] + [CAM FUNCTION]
AGC: ON
[1] + [7] + [6] + [CAM FUNCTION]
AGC: OFF
[1] + [7] + [7] + [CAM FUNCTION]
SENS UP: FIX ON
[1] + [7] + [8] + [CAM FUNCTION]
SENS UP: FIX OFF
[1] + [7] + [9] + [CAM FUNCTION]
Increases electronic sensitivity enhancement (FIX) one step.
[1] + [8] + [0] + [CAM FUNCTION]
Decreases electronic sensitivity enhancement (FIX) one step.
[1] + [8] + [1] + [CAM FUNCTION]
SENS UP: AUTO ON
[1] + [8] + [2] + [CAM FUNCTION]
SENS UP: AUTO OFF
[1] + [8] + [3] + [CAM FUNCTION]
Increases electronic sensitivity enhancement (AUTO) one step.
[1] + [8] + [4] + [CAM FUNCTION]
Decreases electronic sensitivity enhancement (AUTO) one step.
[1] + [8] + [5] + [CAM FUNCTION]
Increases line lock phase (FINE) one step.
[1] + [8] + [6] + [CAM FUNCTION]
Decreases line lock phase (FINE) one step.
[1] + [8] + [7] + [CAM FUNCTION]
Pans 180° .
[1] + [8] + [8] + [CAM FUNCTION]
CLEANING: ON
[1] + [8] + [9] + [CAM FUNCTION]
CLEANING: OFF
[1] + [9] + [0] + [CAM FUNCTION]
BW AUTO switching time: 10 seconds
[1] + [9] + [1] + [CAM FUNCTION]
BW AUTO switching time: 30 seconds
[1] + [9] + [2] + [CAM FUNCTION]
BW AUTO switching time: 60 seconds
[1] + [9] + [3] + [CAM FUNCTION]
BW AUTO switching time: 300 seconds
[1] + [9] + [4] + [CAM FUNCTION]
PATROL2: PLAY
[1] + [9] + [5] + [CAM FUNCTION]
PATROL3: PLAY
[1] + [9] + [6] + [CAM FUNCTION]
PATROL4: PLAY
[1] + [9] + [7] + [CAM FUNCTION]
PATROL2: LEARN start
[1] + [9] + [8] + [CAM FUNCTION]
PATROL3: LEARN start
[1] + [9] + [9] + [CAM FUNCTION]
PATROL4: LEARN start
[2] + [0] + [0] + [CAM FUNCTION]
Turns on auto tracking.
[2] + [0] + [1] + [CAM FUNCTION]
STABILIZER: ON
[2] + [0] + [2] + [CAM FUNCTION]
STABILIZER: OFF
[2] + [0] + [3] + [CAM FUNCTION]
PAN, TILT, ZOOM, coordinate display ON
[2] + [0] + [4] + [CAM FUNCTION]
PAN, TILT, ZOOM, coordinate display OFF
[3] + [0] + [1] + [CAM FUNCTION]∼
Moves to a preset number (1 to 256).*
[5] + [5] + [6] + [CAM FUNCTION]
Example: Preset number 128 _ [4] + [2] + [8] + [CAM FUNCTION]
[6] + [0] + [1] + [CAM FUNCTION]∼
Registers a position to a preset number (1 to 256).*
[8] + [5] + [6] + [CAM FUNCTION]
Example: Preset number 128 _ [7] + [2] + [8] + [CAM FUNCTION]
* Do not do this operation with the previous dome type camera models (WV-CS850 series, WV-CS854, WV-CS854E series, WV-CW860
series, WV-CW864, WV-CW864E series), doing so may cause a malfunction.
-45-
WV-CS950 05.2.14 8:37 PM ページ46
TROUBLESHOOTING
Before requesting service, check the following symptoms to see if you can solve the problem yourself.
If the countermeasures described below do not correct the problem, or if the symptoms you are experiencing are not
covered here, contact a quality service person or system installer.
Problem
Cause and Recommended Action
• Is the camera connected correctly? Check the
operating instructions that come with your system
controller.
No picture (dark screen)
Reference Pages
—
• Is the lens iris closed?
Execute the iris reset from the system controller you
are using.
• Is the camera set up for a fixed shutter speed?
• Is the lens iris open?
22-23
23
22-23
White picture
Out of focus picture
Digital noise in the
picture
• Is FIX selected for the electronic sensitivity
enhancement (SENS UP) setting?
24
• Is the dome cover or lens of the camera dirty? If so,
clean them.
7
• Is MANUAL selected for the auto focus mode?
26
• Is the object one that is not compatible with auto
focus? For such objects, focus manually.
26
• The slip ring may be dirty. Do you have the
cleaning function turned on?
35
• Is the camera set up correctly?
11
-46-
WV-CS950 05.2.14 8:37 PM ページ47
Problem
Poor picture colour
Cause and Recommended Action
Reference Pages
• Check the white balance setting.
25
• Use the special set-up menu to adjust picture
quality.
39
• Is the dome cover or lens of the camera dirty? If so,
clean them.
7
Image flicker
• If Super Dynamic 3 is turned on, turn it off.
Afterimages in
the picture
• Check the DNR setting.
Black and white picture
• The camera has an auto black and white switching
mode function. Check the setting of this mode.
25-26
Frequent switching
between the colour and
the black and white
modes
• Adjust the black and white mode switching level,
and the duration time setting.
25-26
White specks in the
picture
• Use the PIX OFF function to perform blemish
compensation.
39
• Is the camera connected correctly? See the
operating instructions that come with the system
controller you are using.
—
• Are camera communication settings configured
correctly?
12-14
18-19
20
22-23
25
Menu does not open.
-47-
WV-CS950 05.2.14 8:37 PM ページ48
Problem
Cause and Recommended Action
Reference Pages
Menu settings will not
change.
• Is the password lock function turned on?
42
I forgot the password.
• Contact a quality service person or system installer.
—
Picture does not switch
to black and white.
• Switching is not performed when the ALARM IN 4
setting is BW. Check the setting.
38
• Is the camera connected correctly? See the
operating instructions that come with the system
controller you are using.
—
• The camera has a pan limit function. Check the
PAN LIMIT settings.
31
• The motor or lens may be worn. Contact a quality
service person or system installer.
—
• Check the self return function.
30
• Check the ALARM IN settings.
37-38
• Check the recover time setting of the motion
detector.
36-37
Pan, tilt, zoom, or focus
do not work.
The camera movement
modes (OFF, SEQ,
SORT, AUTO PAN,
PATROL, AUTO
TRACK) do not work.
-48-
WV-CS950 05.2.14 8:37 PM ページ49
Problem
Cause and Recommended Action
Reference Pages
The camera movement
mode (OFF, SEQ,
SORT, AUTO PAN,
PATROL, AUTO
TRACK) setting
changes.
• Check the self return function.
30
Camera position is
different from the
preset position setting.
• Perform REFRESH from the special set-up menu.
39
Picture is different from
the position setting.
• Adjust the picture using the preset menu and a
scene file.
27-29
Upper part of the picture
is black when the camera
is in a horizontal
orientation.
• This is caused by the camera's internal cover. It
does not indicate malfunction.
35
• If the cleaning function is turned on, this is normal
does not indicate malfunction. Check the
CLEANING settings.
35
• If the cleaning function is not turned on, this
symptom could be due to noise.
8, 12
Camera suddenly starts
to pan by itself.
● Periodically check the power cord and plug.
Power cord sheathing is
damaged.
Power cord, connectors,
or power plug becomes
hot during operation.
• The power cord, connector, or power plug is damaged. Continued
use creates the risk of electric shock and fire. Immediately unplug
the power plug and contact a qualified service person or system
installer for servicing.
Power cord becomes
warm or hot when it is
bent or stretched during
use.
-49-
SPECIFICATIONS
● General
Power Requirements
Power Consumption
Pick-up Device
Effective Pixels
Scanning Area
Signal
Synchronization
Scanning
Scanning Frequencies
Video Output
Resolution (Centre)
Minimum Illumination
Dynamic Range
S/N Ratio
Ambient Operating Temperature
Dimensions
Weight
Finish
WV-CS954E
WV-CS950
24 V AC, 50 Hz
220 V - 240 V AC, 50 Hz
13 W
1/4-type {1/4"} interline transfer CCD
752 (H) × 582 (V)
3.65 mm (H) × 2.71 mm (V)
PAL
Internal (INT), multiplexed vertical drive (VD2), link-lock (LL)
2:1 interlace
Horizontal: 15.625 kHz, Vertical: 50.00 Hz
VBS: 1.0 V [P-P]/75 Ω (BNC plug)
Horizontal : 480 lines minimum (colour NORMAL mode)
540 lines typ. , 520 lines minimum (colour HIGH mode)
570 lines minimum (black and white)
Vertical : 400 lines minimum (Centre)
0.5 lux (colour mode)
0.04 lux (black and white mode)
SENSE UP: OFF; AGC: HIGH
54 dB typ. (SUPER-D3: ON)
50 dB minimum (AGC: OFF)
-10 °C to 50 °C; Humidity 90 % max. (non-condensation)
154.5 mm (D) × 233 mm (H)
Approximately 2.2 kg
Camera: Die cast aluminum with baked melanin coating (Paint color: Fine silver)
Dome: Clear acrylic resin
● Pan and Tilt
Panning Range
Panning Modes
Panning Speed*
Tilting Range
Tilting Modes
Tilting Speed*
360° endless
Manual, auto, manual position, sequential position
Manual: Approximately 0.065 °/s to 120 °/s 8 steps, 16 steps, 64 steps
Preset: Approximately 400 °/s
-5° to 185° (horizontal - vertical - horizontal)
(According to the TILT ANGLE)
Manual, manual position, sequential position
Manual: Approximately 0.065 °/s to 120 °/s 8 steps, 16 steps, 64 steps
Preset: Approximately 400 °/s
* Actual speed depends on type of controller being used.
● Lens
Zoom Ratio
Focal Length
Maximum Aperture Ratio
Object Distance
Iris Range
Angular Field of View
30x (Approximately 300x with digital zoom)
3.8 mm to 114 mm
1:1.4 (WIDE) to 3.7 (TELE)
1.5 m
F1.4 to 22, Close
Horizontal: 1.9° (TELE) to 52° (WIDE)
Vertical: 1.4° (TELE) to 40° (WIDE)
-50-
● Main Functions
Controller Interface
Control Functions
AGC
Title (ID)
Zoom Speed
Zoom Limit
Password Lock
Auto Focus
Iris
Shutter
Electronic Sensitivity Enhancement
Auto Mode
Auto Pan Key
Digital Flip
SUPER-D3
Motion Detector
Alarm Input/Output
Black and White Mode Switching
Privacy Zone
Patrol
Cleaning
Image Hold
Auto Image Stabilizer
Scene Select Setting
Language Setting
Coaxial Multiplex System, RS485
Pan and tilt, zoom and focus, 256 preset positions, home position, patrol
ON (LOW), ON (MID), ON (HIGH), OFF
ON, OFF (Preset ID, camera ID, area title: 16 alphanumeric characters)
Approximately 6.0 seconds (TELE to WIDE) in manual mode
1x to 300x (Over 30x is electronic zoom)
All menus
MANUAL/AUTO (PAN, TILT, ZOOM linked)
ALC (Adjustable OPEN/CLOSE output target level)/MANUAL
OFF (1/50), AUTO, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000
32X max. (AUTO or FIX)
OFF, SEQ, SORT, AUTO PAN, PATROL, AUTO TRACK
SEQ, SORT, AUTO PAN, PATROL, AUTO TRACK
ON/OFF
ON/OFF
OFF/MODE1/MODE2
4 inputs (ALARM IN 1 to ALARM IN 4)
2 outputs (ALARM/AUX1, BW/AUX2)
AUTO/ON/OFF
ON/OFF (8 zone settings)
STOP/PLAY/LEARN
ON/OFF
ON/OFF
ON/OFF
INDOOR (L) /INDOOR (H) /OUTDOOR (L) /OUTDOOR (H)
Japanese, English, German, French, Italian, Spanish, Russian, Chinese
-51-
WV-CS950/954E Cover(1-4) 05.2.15 5:58 PM ページ 366
Colour CCTV Camera
Operating Instructions
Model Nos.
Printed in Japan
Gedruckt in Japan
Imprimé au Japon
Impreso en Japón
Stampato in Giappone
© 2004 Matsushita Electric Industrial Co., Ltd. All rights reserved.
AM0105-0 3TR003398AAA
WV-CS950
WV-CS954E
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement