Digital Monitoring | XR6 | Installation guide | Digital Monitoring XR6 Installation guide

Digital Monitoring XR6 Installation guide
XR6/XR10/XR20 Command ProcessorTM Panels
Installation Guide
6/10/26 Zone Burglary/Fire/Access Control Panels with Built-in Communicator
2841 E. Industrial Drive Springfield, MO 65802-6310
LT-0229 (4/99)
MODEL XR6/XR10/XR20
COMMAND PROCESSORTM
INSTALLATION GUIDE
FCC NOTICE
This equipment generates and uses radio frequency energy and, if not installed and used properly in strict accordance with
the manufacturer's instructions, may cause interference with radio and television reception. It has been type tested and found
to comply with the limits for a Class B computing device in accordance with the specification in Subpart J of Part 15 of FCC
Rules, which are designed to provide reasonable protection against such interference in a residential installation. If this
equipment does cause interference to radio or television reception, which can be determined by turning the equipment off
and on, the installer is encouraged to try to correct the interference by one or more of the following measures:
Reorient the receiving antenna
Relocate the computer with respect to the receiver
Move the computer away from the receiver
Plug the compute into a different outlet so that computer and receiver are on different branch circuits
If necessary, the installer should consult the dealer or an experienced radio/television technician for additional suggestions.
The installer may find the following booklet, prepared by the Federal Communications Commission, helpful:
"How to identify and Resolve Radio-TV Interference Problems."
This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402
Stock No. 004-000-00345-4
Copyright © 1995 - 1999 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
TABLE OF CONTENTS
Section
Page
Panel Specifications
1.1 Power supply ................................................................................................. 1
1.2 Communication .............................................................................................. 1
1.3 Panel zones ................................................................................................... 1
1.4 Keypads ........................................................................................................ 1
1.5 Outputs .......................................................................................................... 1
1.6 Enclosure specifications ................................................................................ 1
Introduction
2.1 Description .................................................................................................... 2
2.2 System configurations ................................................................................... 2
2.3 Before you begin ........................................................................................... 2
2.4 About this guide ............................................................................................. 2
2.5 How to use this guide .................................................................................... 2
System Components
3.1 Description .................................................................................................... 3
3.2 Wiring diagram .............................................................................................. 3
3.3 Lightning protection ....................................................................................... 3
3.4 Security Command keypads .......................................................................... 3
XR6, XR10 & XR20 Wiring Diagram ...................................................................... 4
Installation
4.1 Mounting the enclosure ................................................................................. 5
4.2 Mounting keypads ......................................................................................... 6
4.3 Wiring Keypads ............................................................................................. 6
Primary Power Supply
5.1 AC terminals 1 and 2 ..................................................................................... 6
5.2 Transformer types ......................................................................................... 6
Secondary Power Supply
6.1 Battery terminals 3 and 4 ............................................................................... 7
6.2 Earth ground .................................................................................................. 7
6.3 Replacement period ...................................................................................... 7
6.4 Discharge/recharge ....................................................................................... 7
6.5 Battery supervision ........................................................................................ 7
6.6 XR6/XR10/XR20 power requirements ........................................................... 7
Standby Battery Power Calculations ...................................................................... 8
Bell Output
7.1 Terminals 5 and 6 .......................................................................................... 9
Keypad Data Bus
8.1 Description .................................................................................................... 9
8.2 Terminal 7 - RED ......................................................................................... 9
8.3 Terminal 8 - YELLOW .................................................................................. 9
8.4 Terminal 9 - GREEN .................................................................................... 9
8.5 Terminal 10 - BLACK ..................................................................................... 9
Smoke and Glassbreak Detector Output
9.1 Terminal 11 ................................................................................................... 9
Burglary Zones
10.1 Description .................................................................................................... 10
10.2 Operational parameters ................................................................................. 10
10.3 Zone response time ....................................................................................... 10
10.4 Keyswitch arming zone .................................................................................. 10
Powered Zone for 2-Wire Smoke Detectors
11.1 Terminals 25 and 26 ...................................................................................... 11
Annunciator Outputs
12.1 Description .................................................................................................... 12
12.2 Harness wiring ............................................................................................... 12
Telephone RJ Connector
13.1 Description .................................................................................................... 12
TABLE OF CONTENTS
Section
Page
13.2 FCC registration ............................................................................................ 12
13.3 Notification ..................................................................................................... 12
13.4 Ground start .................................................................................................. 13
Reset Jumpers J16
14.1 Description .................................................................................................... 13
Universal UL Burglary Specifications
15.1 Introduction .................................................................................................... 13
15.2 Wiring ............................................................................................................ 13
15.3 Police station phone numbers ....................................................................... 13
15.4 Bypass reports .............................................................................................. 13
15.5 System maintenance ..................................................................................... 13
15.6 Cross Zoning ................................................................................................. 13
15.7 Ground Start .................................................................................................. 13
15.8 UL Listed Receivers ...................................................................................... 13
UL 1023 Specifications
16.1 Bell cutoff ....................................................................................................... 14
16.2 Entry delay .................................................................................................... 14
16.3 Exit delay ....................................................................................................... 14
16.4 Zone expansion on 4-wire bus ....................................................................... 14
UL 1610 and 1076 Specifications
17.1 Opening/Closing reports ................................................................................ 14
17.2 Automatic bell test ......................................................................................... 14
17.3 Proprietary dialer ........................................................................................... 14
UL 1635 Specifications
18.1 Digital dialer telephone number ..................................................................... 15
18.2 Entry delay .................................................................................................... 15
18.3 Exit delay ....................................................................................................... 15
18.4 Test frequency ............................................................................................... 15
18.5 Automatic bell test ......................................................................................... 15
18.6 Grade B Central Station ................................................................................. 15
UL 365 and 609 Specifications
19.1 Entry delay .................................................................................................... 15
19.2 Grade A bell .................................................................................................. 15
19.3 Bell cutoff ....................................................................................................... 15
19.4 Automatic bell test ......................................................................................... 15
19.5 Grade A Mercantile ........................................................................................ 15
19.6 Mercantile Safe and Vault .............................................................................. 15
19.7 Line security for Police Connect .................................................................... 15
Universal UL and NFPA Fire Alarm Specifications
20.1 Introduction .................................................................................................... 16
20.2 Wiring ............................................................................................................ 16
20.3 Police station phone number ......................................................................... 16
20.4 System maintenance ..................................................................................... 16
20.5 Audible alarm ................................................................................................. 16
20.6 Fire zone programming ................................................................................. 16
20.7 Ground Start .................................................................................................. 16
20.8 UL Listed Receivers ...................................................................................... 16
UL 985 NFPA 72 (chapter 2) Specifications
21.1 Bell output definition ...................................................................................... 16
21.2 Indicating Circuit Supervision ........................................................................ 16
California State Fire Marshal Specifications
22.1 Bell output definition ...................................................................................... 17
Troubleshooting Section
23.1 Description .................................................................................................... 17
Multiple Indicating Circuit Module
24.1 Installation drawing ........................................................................................ 18
Introduction
Panel Specifications
1.1
Power supply
Transformer Input: 16.5 VAC 40VA (Models 320 wire-in or 321 plug-in)
16.5 VAC 20VA (Model 324 plug-in)
Standby Battery: 12 VDC 7.0Ah (40VA transformer charges up to 2 batteries)
Auxiliary Output: 12 VDC at 500mA
Bell Output: 12 VDC at 1.5 Amps with 40VA transformer, 600mA with 20VA transformer
Smoke Detector Output: 12 VDC at 100mA
All circuits inherent power limited
1.2
Communication
Built-in SDLC Digital Dialer communication to DMP Model SCS-1 Receivers
Built-in 4-2 communication to non-DMP receivers
Built-in M2E (Radionics Modem IIe) communication to non-DMP receivers (XR20 only)
Built-in CID (Contact ID) communication to non-DMP receivers
Either panel can operate as a local system.
1.3
1.4
Panel zones
Nine 1k W EOL burglary zones (zones 1 to 9), (zones 1 to 5 on XR6)
One 3.3k W EOL Class B powered fire zone with reset capability (zone 10 on XR10 and XR20), (zone 6 on XR6)
Keypads
You can connect up to four of the following supervised keypads to the XR6/XR10/XR20 panels.
• 16 or 32 character alphanumeric keypads
• 10-zone LED keypads
In addition, the following zone expanders can be added to the XR20 panel:
• Four and single point zone expanders
• Single point PIR and glassbreak detectors
When using the FA426 Wireless Receiver, the XR20 allows unsupervised devices to be added to address five.
1.5
Outputs
The XR6/XR10/XR20 panels provide four open collector outputs rated for 50mA each. See section 12.1. A Model
300 Wire Harness is required. The open collector outputs provide the ground connection for a positive voltage
source.
1.6
Enclosure specifications
The XR6/XR10/XR20 panel ships in an enclosure with EOL resistors, battery leads, user's guide, and
programming sheet.
Size:
Weight:
Color:
Construction:
12.5" W x 9.5" H x 2.75" D
4 lbs
Gray or Black
20 gauge cold rolled steel
XR6/XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 1
Introduction
Introduction
2.1
Description
The DMP XR6/XR10/XR20 Command Processors are powerful 12 VDC burglary and fire communicator panels
with battery backup. The XR10/XR20 provide nine on-board burglary zones and one on-board 12 VDC Class B
powered fire zone. The XR6 provides five burglary and one fire zone. The fire zone has a reset capability to
provide for 2-wire smoke detectors, relays, or other latching devices. The XR6/XR10/XR20 can communicate to
one or two DMP SCS-1 Receivers using SDLC digital dialer, 4-2, or Contact ID (CID) reporting formats. In
addition, the XR20 can communicate using the Radionics Modem IIe format.
2.2
System configurations
The XR6/XR10/XR20 can be programmed to operate as either an All/Perimeter system that provides one
Perimeter area and one Interior area, or as a Home/Sleep/Away system that provides one Perimeter, one Interior,
and one Bedroom area. The Bedroom area can include any protection devices the user wants disarmed during
their sleeping hours and armed in the Away mode. In addition, the XR20 can operate as a four area system.
2.3
Before you begin
Before installing the XR6/XR10/XR20, we recommend you read through the entire contents of this guide.
Familiarize yourself with the features of the panel and the key points to remember during the installation. Be sure
to read and understand all of the caution statements printed in bold italics.
In addition to this installation guide, you should also read through and familiarize yourself with these other product
documents:
• XR6/XR10 Programming Guide (LT-0230)
• XR20 Programming Guide (LT-0305)
• XR6/XR10 Program Information Sheet (LT-0212)
• XR20 Program Information Sheet (LT-0302)
• XR6/XR10 Security Command User's Guide (LT-0226) • XR20 Security Command User's Guide (LT-0303)
2.4
About this guide
The information contained in this guide is organized into three sections: Table of Contents, Introduction, and
Installation.
• The Table of Contents at the front of this guide lists all of the headings and subheadings used throughout
each section and the page number where the information can be found.
• The Introduction section gives you an overview of the various components that go into a XR6/XR10/XR20
system and diagrams some typical system configurations. This section gives descriptions of the panel,
keypads, and accessory modules and provides details on how each of them operate together in the
system.
• The Installation section begins with mounting instructions for the enclosure and takes you through the
proper way to power up the panel prior to programming.
Caution notes
Throughout this guide you'll see caution notes containing information you need to know when installing the
XR6/XR10/XR20 panel. These cautions are written with a bold, italicized introductory clause followed by a
detailed description of the caution. See the example shown below:
Always ground the panel before applying power to any devices: The XR6/XR10/XR20 must be properly
grounded before connecting any devices or applying power to the panel. Proper grounding protects against
Electrostatic Discharge (ESD) that can damage system components.
Whenever you see a caution note, make sure you completely read and understand its information. Failing to
follow the caution note can cause damage to the equipment or improper operation of one or more components in
the system.
2.5
How to use this guide
To locate information about the installation of the XR6/XR10/XR20, first go to the Table of Contents at the front of
this guide. Find the subject heading that closely describes the information you need and turn to the section
number shown to the right of the heading.
The text that follows the heading has been written to provide as much information about the subject as possible. If
you can't find the information you need under that heading, try scanning through a few of the headings before and
after and reading the text under those that sound similar.
XR6/XR10/XR20 Installation Guide
Page 2
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Introduction
System Components
3.1
Description
The DMP XR6/XR10/XR20 system is made up of an alarm panel with built in communicator, an enclosure, a 16.5
VAC transformer, and a 12 VDC 7.0 Ah battery. You can add up to four Security Command keypads to the system
and can also connect auxiliary devices to the panel's open collector outputs to expand the basic system. Combined
current requirements of additional modules may require an auxiliary power supply. Refer to section 6.6 in this guide
when calculating power requirements. In addition, up to 16 points of zone expansion can be added to the XR20 and
four points to the XR6.
3.2
Wiring diagram
The XR6/XR10/XR20 system wiring diagram in Figure 1 shows some of the accessory devices you can connect
for use in various applications. A complete description of each module follows. Zone expanders can be added to
the XR6 or XR20.
3.3
Lightning protection
Metal Oxide Varistors and Transient Voltage Suppressors help protect against voltage surges on input and output
circuits. A transorb is provided for the Smoke Detector Output Circuit (Terminal 11). This transient protection
provides additional resistance to electrical surges such as lighting. Additional surge protection is available by
installing the DMP 370 or 370RJ Lightning Suppressors.
3.4
Command Processor Accessories
You can connect any combination of up to four Model 670, 770, and 771 vacuum fluorescent, 690, 790, 791, and
793 LCD, or 692 LED Security Command Keypads to the 4-wire keypad data bus provided by the panel on
terminals 7, 8, 9, and 10. Also, you can connect Model 714, 715, 714-8, 714-16, 715-8, 715-16 zone expanders
to the XR20 or XR6 4-wire keypad bus. (Note: The XR10 does not support zone expansion on the keypad bus.)
XR6/XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 3
Introduction
Output Header J11
All outputs must be connected to
devices located within the same room
as the control panel.
DMP transformers:
Model 320
16.5 VAC 40VA
Class 2 wire-in
Use DMP Model 300 Harness.
J11
J16
1
2
3
4
Command Processor Reset
RJ Cable Monitor J7
Use DMP Model 306 Harness
J7
AC wiring must be in conduit and exit
Wiring on
out the left side of the panel enclosure terminals 5 thru
J4
17 must exit to
RJ SUP
the right and
maintain a 1/4"
Phone Jack Connector
separation from
the AC and
battery positive
wiring.
Model 324
16.5 VAC 20VA
Class 2 plug-in
Secondary Power Supply
1.2 Amps max. charging
current. Use only 12 VDC
rechargable batteries. DMP
Model 367. Replace every
3 - 5 years.
Front Tamper
U11
EPROM
Socket
Model 321
16.5 VAC 40VA
Class 2 plug-in
J8
PROG
Plug into
120 VAC
outlet not
controlled
by switch.
AC
AC
+B
Programmer Header J8
Use DMP Model 330 Harness
See detail below
for XR6 panel only
-B BELL GND RED YEL GRN BLK SMK Z1 GND Z2 Z3
GND Z4
Z5 GND Z6
Z7 GND Z8
Rear Tamper
Z9 Z10+ Z10-
Tamper protection when
required for Model 349A
Attack Resistant
Enclosure.
Household System
An alarm sounding
device must be
installed indoors so that
it is clearly heard in all
sleeping areas.
Bell
Smoke
Detector
+-
1K Ω
1K Ω
ZONE 10
ZONE 8
ZONE 9
ZONE 7
ZONE 6
ZONE 5
1K Ω 1K Ω 1K Ω 1K Ω
Smoke Output
100mA @ 10.4 - 13.2 VDC
Red Terminal 11
Black
4-wire smoke detector
Power
Supervision
Relay
Up to 500mA auxiliary
current at 10.4 - 13.2
VDC from Terminal 7.
ZONE 3
1K Ω 1K Ω
ZONE 4
ZONE 2
ZONE 1
22 GA. MIN BLACK
22 GA. MIN YELLOW
Cold Water Pipe Earth Ground
22 GA. MIN GREEN
22 GA. MIN RED
Bell
10.4 - 13.2 VDC
Total current: 1.5 Amps
max. w/ 40 VA
600mA w/20 VA
RED
Maximum AC wire distance
With 16 gauge wire: 70 feet
With 18 gauge wire: 40 feet
BLACK
16 - 18 gauge wire
Zone 10 compatibility
identifier: A
2-wire
smoke
detector
Maximum operating range:
8.8 VDC - 14.2 VDC.
1K Ω
See section 11.1 in the XR6/XR10/XR20
Installation Guide (LT-0229) for a list of
approved 2-wire smoke detectors.
Heat detectors, manual pull
stations, or any other shorting
device. Unlimited number of units.
3.3k Ω
DMP Model 309
ZONE EXPANDER
Model 714
15mA @ 12 VDC
Models 714-8, 714-16
20mA @ 12 VDC
Keypads
Models 670, 770, 771
100mA @ 8 - 16 VDC
125mA with display lit
ZONE EXPANDER
Model 715
15mA @ 12 VDC
Models 715-8, 715-16
20mA @ 12 VDC
XR6 or XR20 only
Models 690, 790,
791, 793
100mA @ 8 - 16 VDC
STAY
POWER
INSTANT
1
2
3
4
5
6
7
8
9
10
STAY
1
ABC
5
MNO
9
INSTANT
2
DEF
6
CODE
3
4
G H I
7
PQR
0
BYPASS
Z3 GND Z4 Z5
Z6+ Z6-
ZONE 6
ARMED
TRBL
ZONE 4
READY
ZONE 5
Model 692
75mA @ 8 -16 VDC
JKL
8
STU
VWX
SPECIAL
COMMAND
2-wire
smoke
detector
YZ
Detail for XR6 only
Figure 1: XR6/XR10/XR20 wiring diagram
XR6/XR10/XR20 Installation Guide
Page 4
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Installation
Installation
4.1
Mounting the enclosure
The metal enclosure must be mounted in a secure, dry place to protect the panel from damage due to tampering
or the elements. It is not necessary to remove the PC board when installing the enclosure.
Dual 1/2" and 3/4" Conduit Knockout
J11
J16
1
2
3
4
Command Processor Reset
J4
Phone Jack Connector
EPROM Socket
U11
1
2
AC
AC
3
+B
4
-B
5
6
7
8
BELL GND RED
10
9
YEL GRN
11
BLK SMK
12
13
Z1
GND
14
15
Z2
Z3
16
GND
17
18
Z4
Z5
19
GND
20
21
Z7
Z6
22
GND
23
Z8
24
Z9
25
26
Z10+ Z10-
Enclosure Mounting Holes
Battery shelf
Figure 2: XR6/XR10/XR20 in standard enclosure
Accessory Module
Mounting Holes
Accessory Module
Mounting Holes
Dual 1/2" and 3/4" Conduit Knockouts
T amper Switch
Mounting Holes
Enclosure Mounting Holes
J1 1
J16
1
2
3
4
Reset Jumper
J4
Phone Jack Connector
EPROM Socket
U1 1
1
AC
2
AC
3
+B
4
5
6
7
8
-B BELL GND RED YEL
9
10
11
GRN BLK SMK
12 13
Z1 GND
14
Z2
15
Z3
16
GND
17
Z4
18
Z5
19
GND
20
Z6
21
Z7
22
GND
23
Z8
24
Z9
25
26
Z10+ Z10-
Enclosure Mounting Holes
Battery Shelf
Dual 1/2" and 3/4" Conduit Knockouts
Figure 2A: XR6/XR10/XR20 in optional 349 Enclosure
XR6/XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 5
Installation
4.2
Mounting keypads
Security Command keypads have removable covers that allow you to easily mount the base to a wall or other flat
surface using the screw holes provided on each corner.
For mounting keypads on solid walls, or for applications where conduit is required, use a DMP 695, 696, 775, or
776 keypad conduit backbox.
4.3
Wiring keypads
Keypad data bus
The keypad data bus consists of a 4-wire cable that provides 12 VDC power, data in, data out, and a panel
common. You can connect keypads in parallel on one 4-wire cable or provide a separate cable run back to the
panel for each keypad. The maximum cable length for one keypad can be up to 500 feet using 22 gauge wire or
up to 1000 feet using 18 gauge wire. Additional keypads installed on the same cable decrease the maximum
distance at which they'll operate properly.
Refer to the 710 Bus Splitter/Repeater Module Installation Sheet (LT-0310) for additional information when
connecting keypads to a keypad bus circuit greater than 2,500 feet.
Primary Power Supply
5.1
AC terminals 1 and 2
Connect the transformer wires to terminals 1 and 2 on the panel. Use no more than 70 ft. of 16 gauge, or 40 ft. of
18 gauge, wire between the transformer and the XR6/XR10/XR20.
Always ground the panel before applying power to any devices: The XR6/XR10/XR20 must be properly
grounded before connecting any devices or applying power to the panel. Proper grounding protects against
Electrostatic Discharge (ESD) that can damage system components. See Earth ground, section 6.2.
5.2
Transformer types
The larger transformer for the XR6/XR10/XR20 is 16.5 VAC 40VA, which provides up to 1.5 Amps of bell output
current, 500mA of auxiliary current, and 100mA of smoke detector output. You can use either the Model 320 wirein or 321 plug-in transformer with the XR6/XR10/XR20. The total current available is limited by the total battery
standby requirements of the installation. When the DMP Model 324 16.5 VAC 20VA plug-in transformer is used,
the bell output current is reduced to 600mA.
The transformer must be connected to a 120 VAC 60 Hz commercial power outlet that is not controlled by a wall
switch. Never share the transformer output with any other equipment.
XR6/XR10/XR20 Installation Guide
Page 6
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Installation
Secondary Power Supply
6.1
Battery terminals 3 and 4
Connect the black battery lead to terminal 4 on the panel and to the negative terminal of the battery. The negative
terminal connects to the enclosure ground internally through the XR6/XR10/XR20 circuit board. Connect the red
battery lead to terminal 3 on the panel and to the positive terminal of the battery. Observe polarity when
connecting the battery. The panel can charge up to two batteries.
Use sealed lead-acid batteries only: Use the DMP Model 367, 12 VDC 7.0Ah sealed lead-acid rechargeable
battery. Batteries supplied by DMP or manufactured by Eagle Picher or Yuasa have been tested to ensure proper
charging with DMP products.
GEL CELL BATTERIES CANNOT BE USED WITH THE XR6/XR10/XR20 PANEL.
6.2
Earth ground
Terminal 4 of the XR6/XR10/XR20 panel must be connected to earth ground using 14 gauge or larger wire to
provide proper transient suppression. DMP recommends connecting to a metal cold water pipe or ground rod
only. Do not connect to electrical conduit or a telephone company ground.
6.3
Replacement period
DMP recommends the battery be replaced every 3 to 5 years under normal use.
6.4
Discharge/recharge
The XR6/XR10/XR20 battery charging circuit float charges at 13.9 VDC at a maximum current of 1.2 Amps using
a 40VA transformer. The total current available is reduced by the combined auxiliary current draw from terminals
7, 11, and 25. The various battery voltage levels are listed below:
Battery Trouble:
Battery Restored:
6.5
Below 11.9 VDC
Above 12.6 VDC
Battery supervision
The XR6/XR10/XR20 tests the battery once every hour when AC power is present. The test lasts for five
seconds. A load is placed on the battery and if its voltage falls below 11.9 VDC a low battery is detected. If AC
power has failed, a low battery is detected any time the battery voltage falls below 11.9 VDC.
If a low battery is detected with AC power present, the test is repeated every two minutes until the battery
charges above 12.6 VDC; the battery restored voltage. If a faulty battery is replaced with a fully charged battery,
the restored battery will not be detected until the next two minute test is done.
6.6
XR6/XR10/XR20 power requirements
During AC power failure, the panel and all auxiliary devices connected draw their power from the battery. All
devices must be taken into consideration when calculating the battery standby capacity. On the following page is
a list of the power requirements of the XR6/XR10/XR20 panel. Add the additional current draw of Security
Command keypads, smoke detector output, and any other auxiliary devices used in the system for the total
current required. The total is then multiplied by the total number of standby hours required to arrive at the total
Ampere/hours required.
XR6/XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 7
Installation
XR6/XR10/XR20 STANDBY BATTERY POWER CALCULATIONS
Standby Current
Command Processor Panel
Active Zones 1-9
Active Zone 10 (zone 6 on XR6)
2-Wire Smoke Detectors
Qty _____ x
Qty _____ x
50mA
1.6mA
4mA
.1mA
Alarm Current
______ mA
______ mA Qty _____ x
______ mA
______ mA Qty _____ x
Bell Output
50mA
*2mA
30mA
.1mA
______ mA
______ mA
______ mA
______ mA
1500mA max. ______ mA
670, 770, and 771 Keypads
Annunciator (ON)
Qty _____ x
125mA ______ mA Qty _____ x 125mA ______ mA
Qty _____ x 20mA ______ mA
690, 693, 790, 791, and 793 Keypads
Annunciator (ON)
Qty _____ x
100mA ______ mA Qty _____ x 100mA ______ mA
Qty _____ x 20mA ______ mA
692 Keypads
Annunciator (ON)
Qty _____ x
30mA ______ mA Qty _____ x
Qty _____ x
30mA ______ mA
10mA ______ mA
710 Bus Splitter/Repeater
Qty _____ x
30mA ______ mA Qty _____ x
30mA ______ mA
711 or 714 Zone Expander
Active Zones (EOL installed)
Qty _____ x
Qty _____ x
7mA ______ mA Qty _____ x
1.6mA ______ mA Qty _____ x
7mA ______ mA
*2mA ______ mA
715 Zone Expander
Active Zones (EOL installed)
2-Wire Smokes
Qty _____ x
Qty _____ x
Qty _____ x
7mA ______ mA Qty _____ x
4mA ______ mA Qty _____ x
.1mA ______ mA Qty _____ x
7mA ______ mA
30mA ______ mA
.1mA ______ mA
714-8 or 714-16 Point Zone Expanders
Active Zones (EOL installed)
Qty _____ x
20mA ______ mA
1.6mA ______ mA Qty _____ x
20mA ______ mA
*2mA ______ mA
715-8 or 715-16 Point Zone Expanders
Active Zones (EOL installed)
2-Wire Smokes
Qty _____ x
Qty _____ x
20mA ______ mA
4mA ______ mA Qty _____ x
.1mA ______ mA Qty _____ x
20mA ______ mA
30mA ______ mA
.1mA ______ mA
Qty _____ x
30mA ______ mA
1.6mA ______ mA Qty _____ x
30mA ______ mA
*2mA ______ mA
20mA ______ mA
738A Ademco Wireless Interface
w/Receiver
75mA ______ mA
75mA ______ mA
FA426 16 Point Receiver
50mA ______ mA
50mA ______ mA
733 Wiegand Interface
Active Zones (EOL installed)
Annunciator (ON)
740/741/743 SC Keypads
Annunciator (ON)
Qty _____ x
50mA ______ mA Qty _____ x 100mA ______ mA
Qty _____ x 20mA ______ mA
Auxiliary Powered Devices on
Terminals 7 and 11
(Other than keypads)
______ mA
Total Standby ___________ mA
______ mA
Total Alarm ____________ mA
Total Standby ____________ mA x number of standby hours needed ______ = ___________ mA/hours
* Based on 10% of active
zones in alarm condition
Total Alarm + ___________ mA/hours
Total ___________ mA/hours
x _.001_____
= ___________ A/hours required
XR6/XR10/XR20 Installation Guide
Page 8
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Installation
Bell Output
7.1
Terminals 5 and 6
Nominal 12 VDC is supplied by terminal 5 on the panel to power alarm bells or horns. The output is rated for a
maximum of 1.5 Amps with a 40VA transformer and 600mA with a 20VA transformer. This output can be steady
or pulsed depending upon the Bell Action specified in Output Options programming. Terminal 6 is the ground
reference for the bell circuit.
Keypad Data Bus
8.1
Description
Terminals 7, 8, 9, and 10 of the XR6/XR10/XR20 panel are designated as the keypad data bus. In addition to
keypads, the XR20 allows the connection of any combination of zone expanders, 5845LX Glassbreak Detectors,
6155LX PIRs, and DS775LX PIRs to the data bus up to the maximum of four devices. The XR6 allows the
connection of four zones on address one.
8.2
Terminal 7 - RED
Nominal 12 VDC is supplied at terminal 7 to power Security Command keypads and zone expanders. This is also
where power for any auxiliary device is supplied. The ground reference for terminal 7 is terminal 10. The
maximum output is rated at 500mA. All auxiliary devices totaled together must not exceed the panel's maximum
current rating of 500mA.
8.3
Terminal 8 - YELLOW
Data receive from keypads and zone expanders.
8.4
Terminal 9 - GREEN
Data transmit to keypads and zone expanders.
8.5
Terminal 10 - BLACK
Terminal 10 is the ground reference for Security Command keypads, zone expanders, and any auxiliary devices
being powered by terminals 7 and 11.
Smoke and Glassbreak Detector Output
9.1
Terminal 11
Nominal 12 VDC at 100mA maximum (shared by terminal 25) is supplied at terminal 11 to power 4-wire smoke
detectors or other auxiliary powered devices. This output can be turned off by the user for 5 seconds using the
Sensor Reset Menu Option. Terminal 10 is the ground reference for terminal 11.
XR6/XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 9
Installation
Burglary Zones
10.1 Description
The XR10/XR20 terminals 12 to 24 are the nine burglary zones. For programming purposes, the zone numbers
are 1 to 9. The zone configurations on terminals 12 to 24 are described below. The XR6 terminals 12 to 18 are
the five burglary zones with terminal 16 providing the ground for zone 5.
Terminal
12
13
14
15
16
17
18
Function
Zone 1 voltage sensing
Ground for zones 1 & 2
Zone 2 voltage sensing
Zone 3 voltage sensing
Ground for zones 3 & 4 (& 5 on XR6)
Zone 4 voltage sensing
Zone 5 voltage sensing
Terminal
19
20
21
22
23
24
Function
Ground for zones 5 & 6
Zone 6 voltage sensing
Zone 7 voltage sensing
Ground for zones 7, 8, & 9
Zone 8 voltage sensing
Zone 9 voltage sensing
The voltage sensing terminal measures the voltage flowing through the 1k W End Of Line resistor to the zone's
ground terminal. Dry contact sensing devices can be used in series (normally-closed) or in parallel (normallyopen) with any of the burglary protection zones.
10.2 Operational parameters
Each burglary protection zone detects three conditions: open, normal, and short.
The parameters for each are listed below:
Condition
Resistance on zone
Voltage on right terminal
Open
over 1300 ohms
over 2.0 VDC
Normal
600 to 1300 ohms
1.2 to 2.0 VDC
Short
under 600 ohms
under 1.2 VDC
1K
NORMALLY CLOSED CONTACTS
1K
1K
NORMALLY OPEN CONTACTS
COMBINATION: NORMALLY OPEN AND
NORMALLY CLOSED CONTACTS
Figure 3: Protection zone contact wiring
10.3 Zone response time
A condition must be present on a zone for 500 milliseconds before it's detected by the XR6/XR10/XR20 panel.
Ensure detection devices used on the protection zones are rated for use with this delay.
10.4 Keyswitch arming zone
Momentary keyswitches
You can use a momentary keyswitch on a zone programmed as an Arming type for use in arming and disarming
the system without a code.
XR6/XR10/XR20 Installation Guide
Page 10
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Installation
Powered Zone for 2-Wire Smoke Detectors
11.1 Terminals 25 and 26
A resettable 2-wire Class B powered zone is provided on terminals 25 (positive) and 26 (negative) of the panel.
For programming purposes, the zone number is 10 on the XR10/XR20 and zone 6 on the XR6. The zone uses a
Model 309, 3.3k W EOL resistor (provided with the panel) and has an operating range of 8.8 to 14.2 VDC.
Power is dropped from zone 10 any time a Sensor Reset is performed on the panel. Whenever non-Fire and nonSupervisory zone types are used on zone 10, make the appropriate adjustments to the zone's Armed Action to
prevent false alarms from occurring.
The UL compatibility identifier is: A.
Manufacturer
Model
Detector
ID
ID
Base
Base ID
# of
Detectors
XR
Panel
Zone Expander
Detection Systems
DS282
B
None
N/A
10
10/20
715, 715-8, 715-16
Detection Systems
DS282TH
B
None
N/A
10
10/20
715, 715-8, 715-16
Detection Systems
DS250
B
MB2W
A
10
10/20
715, 715-8, 715-16
Detection Systems
DS250TH
B
MB2W/MB2WL
A
10
10/20
715, 715-8, 715-16
Detection Systems
DS250HD
B
MB2W/MB2WL
A
10
10/20
715, 715-8, 715-16
Hochiki
SLK-12
HD-4
HSB-12-1, HSB-12-1N
HB-80
20
10/20
715, 715-8, 715-16
DMP/Hochiki
SLK-835
HD-5
HSB-200, HSB-200N
HB-55
7
10/20
715, 715-8, 715-16
DMP/Hochiki
SLK-835H
HD- 5
HSB-200,HSB-200N
HB-55
7
10/20
715, 715-8, 715-16
Sentrol/ESL
429AT
S09A
None
N/A
12
10/20
715, 715-8, 715-16
Sentrol/ESL
521B
S09A
None
N/A
12
10/20
715, 715-8, 715-16
Sentrol/ESL
521BXT
S09A
None
N/A
12
10/20
715, 715-8, 715-16
System Sensor
1100
STD
None
N/A
10
20
715
System Sensor
1151
STD
B110LP
N/A
10
20
715
System Sensor
1400
STD
None
N/A
10
10/20
715
System Sensor
1451
STD
B401, B401B
N/A
10
10/20
715
System Sensor
2100
STD
None
N/A
10
10/20
715
System Sensor
2400
STD
None
N/A
10
10/20
715
System Sensor
2451
STD
B401, B401B, DH400
N/A
10
10/20
715
System Sensor
1451DH
STD
DH400
N/A
10
10/20
715
System Sensor
2100T
ST D
None
N/A
10
10/20
715
System Sensor
2400AT
STD
None
N/A
10
10/20
715
System Sensor
2400AIT
STD
None
N/A
10
10/20
715
System Sensor
2400TH
STD
None
N/A
10
10/20
715
System Sensor
2451TH
STD
B401, B401B
N/A
10
10/20
715
Figure 4: Compatible 2-wire smoke detectors
XR6/XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 11
Installation
Annunciator Outputs
12.1 Description
The four annunciator outputs can be programmed to indicate the activity of the panel's zones or conditions
occurring on the system. Annunciator outputs do not provide a voltage but instead switch to ground
voltage from another source. The outputs can respond to any of the conditions listed below:
1)
2)
3)
4)
5)
7)
8)
9)
10)
Activation by zone condition: Steady, Pulse, Momentary, or Follower
Manually from the Security Command keypad
Communication failure
Armed area annunciation
Fire Alarm or Fire Trouble
Ambush alarm
Exit and Entry timers
System Ready
Ground start activation
12.2 Harness wiring
The open collector outputs are accessible by installing the DMP 300 Harness on the 4-pin header labeled J11.
The output locations are shown below:
Output
Color
Wire
1
Red
1
2
Yellow
2
3
Green
3
4
Black
4
For UL applications, devices connected to the outputs must be located within the same room as the
XR6/XR10/XR20 panel.
Programming Connection
A locking four pin header is provided to connect a keypad when using a DMP Model 330 Programming Cable.
This provides a quick and easy connection for programming the panel.
Telephone RJ Connector
13.1 Description
Connect the panel to the public telephone network by installing a DMP 356 RJ Cable between the panel's J4
connector and the RJ31X or RJ38X phone jack.
Phone Cable Monitor
A two pin header labeled RJ SUP (J7) is provided to allow monitoring of the telephone cable connected between
the panel and a RJ38X jack (pins 2 & 7 jumpered). Attach a DMP Model 306 Harness between J7 and any
available zone. The pins of J7 are connected via the telephone cable to 2 & 7 of the RJ38X jack. The RJ38X jack
provides a jumper between pins 2 & 7 which completes the circuit.
When the zone is programmed for a Supervisory type (SV) and the telephone cable is removed, the keypad will
display the zone in trouble and produce a steady tone.
13.2 FCC registration
The Model XR6/XR10/XR20 complies with FCC part 68 and is registered with the FCC.
Registration number: CCKUSA - 18660 - AL - R
Ringer Equivalence: 1.1B
13.3 Notification
Registered terminal equipment must not be repaired by the user. In case of trouble, the device must be
immediately unplugged from the telephone jack. The factory warranty provides for repairs. Registered terminal
equipment may not be used on party lines or in connection with coin telephones. Notification must be given to the
telephone company of:
a. The particular line(s) the service is connected to
b. The FCC registration number
c. The ringer equivalence
d. The make, model, and serial number of the device
XR6/XR10/XR20 Installation Guide
Page 12
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Installation
13.4 Ground start
To configure the XR6/XR10/XR20 for ground start operation, you must install the appropriate ground start module
and program one of the panel's available annunciator outputs for Ground Start operation. Refer to the
XR6/XR10/XR20 Programming Guide for complete programming information. This option must not be selected on
a UL listed system.
Reset Jumpers J16
14.1 Description
There are two reset jumpers located at the top right of the panel's circuit board labeled RESET. Momentarily
shorting these jumpers allows you to reset the microprocessor of the XR6/XR10/XR20. Resetting the panel allows
you to enter the panel's internal programmer.
To reset the panel when first installing the system, place the blade of a slotted screwdriver across the two reset
jumpers after applying power to the panel.
To reset the panel while the system is operational (for example, prior to reprogramming), you can short the
jumpers without powering down the system.
After resetting the panel for programming, you must begin within 30 minutes. If you wait longer than 30 minutes,
you'll have to reset the panel again.
UNIVERSAL UL BURGLARY SPECIFICATIONS
15.1 Introduction
The programming and installation specifications contained in this section must be completed when installing the
XR6/XR10/XR20 panel in accordance with any of the UL burglary standards. Additional specifications may be
required by a particular standard.
15.2 Wiring
All wiring must be in accordance with NEC, ANSI/NFPA 70, UL 681, and UL 611 for all burglary installations.
15.3 Police station phone numbers
The digital dialer telephone number programmed for communication must not be a police station phone number,
unless that phone number is specifically provided for that purpose.
15.4 Bypass reports
The bypass reports option must be programmed as YES for all UL burglary applications. See section 5.5 of the
XR6/XR10 Programming Guide (LT-0230) and XR20 Programming Guide (LT-0305).
15.5 System maintenance
Proper installation and regular maintenance by the installing alarm company and frequent testing by the end user
is essential to ensure continuous satisfactory operation of any alarm system. Offering a maintenance program
and acquainting the user with the correct procedure for use and testing of the system is also the responsibility of
the installing alarm company.
15.6 Cross zoning
Zones used for cross zoning must be installed to allow detection of the same event. Cross zoning shall not
conflict with UL 681 or 1641.
15.7 Ground Start
Ground Start phone lines must not be used for UL listed systems.
15.8 UL Listed Receivers
UL has verified operation with the DMP SCS-1 Security Receiver, Sur-Gard SG-HLR2-DG, FBII CP220PB,
Osborne-Hoffman Quick-Alert and Radionics D6500 receivers.
XR6/XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 13
Installation
UL 1023 SPECIFICATIONS
Household Burglar-Alarm System Units
16.1 Bell cutoff
The bell cutoff time cannot be less than five minutes. See section 7.2 of the XR6/XR10 Programming Guide
(LT-0230) and XR20 Programming Guide (LT-0305).
16.2 Entry delay
The maximum entry delay used must not be more than 45 seconds. See section 6.4 of the XR6/XR10
Programming Guide (LT-0230) and XR20 Programming Guide (LT-0305).
16.3 Exit delay
The maximum exit delay used must not be more than 60 seconds. See section 6.5 of the XR6/XR10
Programming Guide (LT-0230) and XR20 Programming Guide (LT-0305).
16.4 Zone expansion on 4-wire bus
When expansion zones are used, the keypad and zone expander 4-wire bus must be limited to three feet in
length unless an external communication fail indicator is added. A 12 VDC relay may be wired as a
communication fail indicator. To install, connect the negative side of the indicator to one of the panel's
annunciator outputs and the positive side to the smoke power (terminal 11 of the XR6/XR10/XR20 panel). See
section 7.5C of the XR6/XR10 Programming Guide (LT-0230) and XR20 Programming Guide (LT-0305).
In addition to the wiring described above, a 24 hour zone must be programmed to activate the appropriate
annunciator output.
Normally Closed
Voltage output
from terminal 11
+
Zone activated
annunciator output
Ð
Voltage output
from terminal 11
+
Zone activated
annunciator output
Ð
Common
Normally Open
1k Ohm
Device Fail LED
UL 1610 and 1076 SPECIFICATIONS
Central-Station and Proprietary Burglar-Alarm Units
17.1 Opening/Closing reports
The Opening/Closing Reports option must be programmed as YES. See section 5.2 of the XR6/XR10
Programming Guide (LT-0230) and XR20 Programming Guide (LT-0305).
17.2 Automatic bell test
This option must be programmed as YES. See section 7.3 of the XR6/XR10 Programming Guide (LT-0230) and
XR20 Programming Guide (LT-0305).
17.3 Proprietary dialer
The Model XR6/XR10/XR20 provides Grade A proprietary service when configured as a digital dialer.
XR6/XR10/XR20 Installation Guide
Page 14
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Installation
UL 1635 SPECIFICATIONS
Digital Burglar Alarm Communicator System Units
18.1 Digital Dialer telephone number
Both programmed telephone numbers must begin with a D or P. See sections 3.17 and 3.18 of the XR6/XR10
Programming Guide (LT-0230) and XR20 Programming Guide (LT-0305).
18.2 Entry delay
The maximum entry delay used must not be more than 60 seconds. See section 6.4 of the XR6/XR10
Programming Guide (LT-0230) and XR20 Programming Guide (LT-0305).
18.3 Exit delay
The maximum exit delay used must not be more than 60 seconds. See section 6.5 of the XR6/XR10
Programming Guide (LT-0230) and XR20 Programming Guide (LT-0305).
18.4 Test frequency
The Test Frequency option must be programmed so that the panel sends a report once every 24 hours. See
section 3.6 of the XR6/XR10 Programming Guide (LT-0230) and XR20 Programming Guide (LT-0305).
18.5 Automatic bell test
This option must be programmed as YES. See section 7.3 of the XR6/XR10 Programming Guide (LT-0230) and
XR20 Programming Guide (LT-0305).
18.6 Grade B Central Station
Grade B Central Station service can be provided under UL 1635 by adding a Grade A local audible signal
appliance and placing the Model XR6/XR10/XR20 panel into the Model 349A Grade A Attack Resistant Housing.
UL 365 and 609 SPECIFICATIONS
Police Station Connected and Local Burglar Alarm Units and Systems
19.1 Entry delay
The maximum entry delay used must not be more than 60 seconds when using the Model 349A Grade A housing.
See section 6.4 of the XR6/XR10 Programing Guide (LT-0230) and XR20 Programming Guide (LT-0305).
19.2 Grade A bell
A Grade A local audible signal appliance must be used.
19.3 Bell cutoff
The bell cutoff time cannot be less than 15 minutes. See section 7.2 of the XR6/XR10 Programming Guide
(LT-0230) and XR20 Programming Guide (LT-0305).
19.4 Automatic bell test
The Automatic Bell Test option must be programmed as YES. See section 7.3 of the XR6/XR10 Programming
Guide (LT-0230) and XR20 Programming Guide (LT-0305).
19.5 Grade A Mercantile
For Grade A Mercantile and Police Station Connect operation the Model XR6/XR10/XR20 must be mounted in a
Grade A attack resistant housing, (DMP Model 349A).
19.6 Mercantile Safe and Vault
When the DMP Model 349A housing is used, the XR6/XR10/XR20 provides operation as a mercantile safe and
vault alarm. Bell Supervision and wiring must be in accordance with UL 681. If the panel is mounted outside the
safe or vault, tamper protection and the Sentrol Model 5402 or Potter EVD listed vibration detectors should be
used. The XR6/XR10/XR20 does not provide operation as a Bank Safe and vault alarm.
19.7 Line security for Police Connect
Basic line security is provided when the Model XR6/XR10/XR20 is configured as a dialer system.
XR6/XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 15
Installation
UNIVERSAL UL and NFPA FIRE ALARM SPECIFICATIONS
20.1 Introduction
The programming and installation specifications contained in this section must be completed when installing the
Model XR6/XR10/XR20 in accordance with any of the UL or NFPA fire standards. Additional specifications may
be required by a particular standard.
20.2 Wiring
All wiring must be in accordance with NEC, ANSI/NFPA 70.
20.3 Police station phone number
The digital dialer telephone number programmed for communication must not be a police station phone number,
unless that phone number is specifically provided for that purpose.
20.4 System maintenance
Proper installation and regular maintenance by the installing alarm company and frequent testing by the end user
is essential to ensure continuous satisfactory operation of any alarm system. Offering a maintenance program
and acquainting the user with the correct procedure for use and testing of the system is also the responsibility of
the installing alarm company.
20.5 Audible alarm
Fire Type zones should be programmed to activate an audible alarm. The Bell Action for Fire Type zones should
not be programmed as “N”. See section 7.4A in the XR6/XR10 Programming Guide (LT-0230) and XR20
Programming Guide (LT-0305).
20.6 Fire zone programming
Fire zones must be programmed to activate a trouble on open conditions and an alarm on short conditions. The
swinger bypass function must not be used on any fire zones. See section 8.8 in the XR6/XR10 Programming
Guide (LT-0230) and XR20 Programming Guide (LT-0305).
20.7 Ground Start
Ground Start phone lines must not be used for UL listed systems.
20.8 UL Listed Receivers
UL has verified operation with the DMP SCS-1 Security Receiver, Sur-Gard SG-HLR2-DG, FBII CP220PB,
Osborne-Hoffman Quick-Alert and Radionics D6500 receivers.
UL 985 NFPA 72 (chapter 2) SPECIFICATIONS
Household Fire Warning System Units
21.1 Bell output definition
The bell output of the Model XR6/XR10/XR20 must be programmed to operate steady on burglary alarms and
pulsed on fire alarms. See sections 7.4A and 7.4B of the XR6/XR10 Programming Guide (LT-0230) and XR20
Programming Guide (LT-0305).
21.2 Indicating Circuit Supervision
The DMP Models 865 and 866 Notification Circuit Module must be used on the bell circuit for detection of shorts
and grounds. See Section 24.1 for wiring diagrams.
XR6/XR10/XR20 Installation Guide
Page 16
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Troubleshooting
CALIFORNIA STATE FIRE MARSHAL SPECIFICATIONS
22.1 Bell output definition
The bell output of the Model XR6/XR10/XR20 must be programmed to operate steady on burglary alarms and
temporal on fire alarms. See sections 7.4A and 7.4B of the XR6/XR10 Programming Guide (LT-0230) and XR20
Programming Guide (LT-0305).
Troubleshooting Section
Description
This section of the XR6/XR10/XR20 Installation Guide provides troubleshooting information for use when
installing or servicing an XR6/XR10/XR20 system.
Problem
Possible Cause
Solution
J16 reset jumper is installed.
Remove the J16 reset jumper.
Open or short on the green data
wire to the keypad.
Check for broken or shorted wires
between the keypad and panel.
Bad keypad or zone expander.
Replace with a new or repaired
keypad or zone expander.
Keypad display is not functional.
When a key is pressed, only a
short beep is emitted.
Open or short condition on the
yellow data wire.
Check for broken or shorted
wires.
Bad keypad or zone expander.
Replace with a new or repaired
keypad or zone expander.
Keypad beeps when keys are
pressed but won't allow the user
to arm or enter the User Menu.
Two or more keypads are assigned
to the same address.
Security Command keypads
display " SERVICE REQUIRED"
Set each keypad to a different
address to match the Device
Setup programming.
XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 17
XR6/XR10/XR20 Installation Guide
E. Industrial Drive Springfield, MO
2841 E. Industrial Drive Springfield,
MO 65802-6310 2841
800-641-4282
Page 18
Digital Monitoring Products
1k Ω
Bell A Ð Output
11
Bell Trouble
S
S
S
S
S
S
S
DMP Model 865
85mA at 12 VDC
S
S
S
S
S
S
12 or 24 VDC
5 Amp Maximum
Notification Circuit Module
10
9
Bell Trouble
Bell B Ð Output
Bell B + Output
6
7
Bell A + Output -
8
5
Bell Power Ð Input
3
2
1
4
Alarm Input
Ground
Auxiliary Power
Power Supply
Trouble Contacts
N/C
AUXILIARY
POWER
SUPPLY
8
7
6
5
4
3
2
1
Bell Power + Input
12 or 24 VDC
5 Amp Maximum
Bell Trouble
Bell Trouble
Bell Output -
Bell Output +
Bell Power Input
Alarm Input
Ground
Auxiliary Power
DMP Model 866
37mA at 12 VDC
Notification Circuit Module
Style W
AUXILIARY
POWER
SUPPLY
3
+B
2
AC
1
AC
4
-B
6
Power Supply
Trouble Contacts
N/C
7
S
BELL GND RED
5
9
10
11
12
13
L1
14
GND
15
L2
S = Supervised Circuit
GND
16
L3
J16
S
GND
17
S
L4
18
L5
19
GND
20
L6
21
Command Processor Reset
22
L7
23
GND
24
L8
The Auxiliary Power Supply and Indicating Circuit Module
trouble contact zone must be programmed as a Supervisory
Type zone and must be selected for display in the keypad
status list.
S
YEL GRN BLK SMK
8
Phone Jack Connector
J4
NOTE: If an auxiliary supply is not used,
terminals 3 and 4 on the 866 Indicating
Circuit Module can be jumpered together
to supply bell power from the XR20 panel.
A maximum of 1.5 Amps at 12 VDC is
available from terminal 5 of the XR20.
Each 865 Notification Circuit Module
in alarm draws up to 85mA from its
terminal 3 alarm input.
UL Listed, Polarized
Indicating Devices.
Style Z
Each 866 Indicating Circuit Module
in alarm draws up to 35mA from its
terminal 3 alarm input.
UL Listed, Polarized
notification Devices.
10k Ω EOL Resistor
DMP Model 308
25
L9-
L9+
26
J11
28
L10- L10+
27
U11
EPROM Socket
Optional Module installation
1
2
3
4
Installation
24.1 XR20 Multiple Indicating Circuit Module Installation
65802-6310 800-641-4282
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising