Whynter Freestanding 3.6 cu. ft. Wine Cooler and Cigar Humidor Center

Whynter Freestanding 3.6 cu. ft. Wine Cooler and Cigar Humidor Center
Whynter Freestanding 3.6 cu. ft. Wine Cooler and Cigar Humidor
Center
Model # : CWC-351DD
INSTRUCTION MANUAL
Congratulations on your new Whynter product. To ensure proper operation, please read this Instruction Manual carefully before
using this product. Keep this manual in a safe place for future reference.
Table of Contents
PAGE
Safety Precautions
3-4
Parts and Controls
5
Features and Technical Data
6
About Cigars / Terminology
7
Installation
8-9
Operation and Controls
10 - 11
Care and Maintenance
12
Troubleshooting
13
Warranty Information
14
2
Safety Precautions
APPLIANCE SAFETY
Your safety and the safety of others are very important to us.
To reduce the risk of fire, electrical shock, or injury when using your appliance, follow
these basic precautions
This is the Safety Alert Symbol. This symbol alerts you to potential hazards
that may result in serious injury. All safety messages will follow the Safety
Alert Symbol and either the words” DANGER” or “WARNING”.
Danger means that failure to heed this safety
statement may result in severe injury or death.
Warning means that failure to heed this safety
statement may result in extensive product damage, serious injury, or death.
Caution means that failure to heed this safety
statement may result in minor or moderate injury,
or property or equipment damage.
All safety messages will alert you to know what the potential hazard is, tell you how to reduce the
chance of injury, and let you know what can happen if the instructions are not followed.
IMPORTANT SAFEGUIDES
Before the appliance is used, it must be properly positioned and installed as
described in this manual, please read the manual carefully. To reduce the
risk of fire, electrical shock or injury when using the appliance, follow basic
precaution, including the following:
 Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do
not use an extension cord.
 Do not use if the power supply cord is damaged. If damaged, it must be replaced by a qualified electrician.
 It is recommended that a separate circuit, serving only your appliance be provided. Use receptacles
that cannot be turned off by a switch or pull chain.
 Never clean appliance parts with flammable fluids or harsh chemicals. These fumes can create a fire
hazard or explosion.
 Do not store or use gasoline or other flammable vapors and liquids in the vicinity of the appliance or
any other appliance.
 Before proceeding with cleaning and maintenance operations, make sure to unplug the appliance.
 Do not connect or disconnect the electric plug with wet hands.
 Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in
this manual. All other servicing should be referred to a qualified technician.
3
Safety Precautions
FOLLOW WARNING CALL OUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL

Use two or more people to move and install the appliance. Failure to do so can result in injury.

When positioning the wine cooler, ensure that there is at least a 4” clearance at the sides and a
6” clearance at the back.

Please note that this is a freestanding appliance and should not be placed into a built-in
space. Even with the recommended clearance, there may not be adequate airflow.

It is recommended that you install the wine cooler in a place where the ambient temperature is
between (68°F- 78°F). This appliance must be installed in an area protected from the element,
such as wind, rain, water spray or drips.

The appliance should not be located next to ovens, grills or other sources of high heat.

The appliance must be installed with all electrical connections in accordance with state and local
codes.

The fuse (or circuit breaker) size should be 15 amperes.

It is important for the appliance to be leveled in order to work properly. For a stable installation,
make sure the appliance is placed on a flat, level and solid surface.

Ensure that the surface on which the appliance is placed is strong enough to hold the appliance
and the items stored inside.

This appliance is not intended for use by young children or physically-challenged persons without
supervision/assistance. Young children must be supervised to ensure safety around this or any
appliance.

Do not use solvent-based cleaning agents of abrasives on the interior. These cleaners may damage or discolor the interior.

Keep fingers out of the “pinch point” areas. Clearance between the doors and between the doors
and cabinet are necessarily small. Be careful closing doors when children are in the area.

Close the wine cooler immediately after putting in any items to keep the internal temperature relatively constant.

Avoid placing any objects on top of the appliance.

This is an electrical appliance, to avoid injury from electrical shock do not operate the unit with
wet hands, while standing on a wet surface or while standing in water. Do not use outdoors or in
wet conditions.

When positioning or moving the appliance, ensure that it is not turned up side down or unleveled
greater than 45°.

Never pull the power cord to disconnect it from the outlet. Grasp the plug and pull it from the outlet.

Never lift, carry or drag the appliance by the power cord.

This appliance is designed for household, non-commercial use only. Any other use will void the
warranty.

Do not plug into the power outlet before set up is completed.

Do not cut or remove the ground prong from the power cord.

Do not move this appliance without emptying it and securing the door in a closed position.
4
Parts and Controls
WINE COOLER SIDE | CIGAR HUMIDOR CENTER SIDE
5
1
10
6
2
7
8
9
3
11
4
12
13
16
14
17
18
19
20
15
1. Lights (2)
11. Drip Trays (2)
2. Internal Fans (4)
12. Power Cord
3. Removable premium stainless steel trimmed scalloped shelves (7)
13. Control Panel
4. Leveling Legs ( 2big, 2 small under door hinge)
14. Door Handles (2)
5. Hinge Covers (2)
15. Door Frame
6. Door Seals (2)
16. Temperature Display
7. Glass Doors (2)
17. Up Button
8. Hygrometer
18. Down Button
9. Removable Spanish cedar drawers (3)
and shelves (4)
19. Light Switch
10. Air Filters(4)
20. Humidity Tray
5
Features and Technical Data
Store all your finest wine and cigar in one unit with the Whynter Freestanding 3.6 cu. ft. Wine Cooler and Cigar
Humidor Center. Ideal for those with limited space, not only this multi-purpose cooler can hold an array of beverages from wine to water bottles, but also the perfect cigar storage system that can help preserve the flavor of
your cigars and protect them from pests or other harmful conditions. Between two individual temperaturecontrolled compartments, up to 16 bottles of wine bottles and 350 cigars can be stored. Each zone features its
own temperature control and digital display. The Whynter CWC-351DD has no moving parts and is CFC-free,
which means that you get silent, long-lasting, and environmentally safe refrigeration for your collection.













Capacity: 3.6 cu. ft.
Freestanding setup
Vibration-free thermoelectric cooling
Stainless steel trimmed glass door with sleek black cabinet
Professional quality towel bar handle
3 removable Spanish cedar drawers and 4 shelves
7 removable premium stainless steel trimmed scalloped shelves
Adjustable thermostat with temperature range from 46ºF - 66ºF
Enhanced LCD temperature display
Soft interior LED lighting with on/off switch
Solid state components for long life - the only moving parts are fans to circulate air for even
temperature distribution
Internal fan-forced circulation for even temperature distribution throughout the cabinet
ETL Certified
TECHNICAL DATA
MODEL :
CWC-351DD
Capacity
3.6 cu.ft.
Wine bottle capacity:
16 bottles
Cigar capacity:
Holds up to 350+ cigars
Voltage
110V / 60Hz
Current
3A
Input Power
210W
Power Consumption
1.5KWh/24h
Temperature Control Range
46°F - 66°F
Net Weight
69.5 lbs
Gross Weight
75 lbs
Drawer Dimensions
7.1” W x 12” D x 3” H
Flat Shelves Dimensions
7.1” W x 12” D
Unit Dimensions
21” W x 21” D x 33” H
Packaging Dimensions
24” W x 24” D x 35” H
6
About Cigars/Terminology
Amatista
Band
Binder
Blend
Bloom
Bouquet
Bunch
Cap
Cigarillos
A glass jar containing 50 (or 25) cigars, sealed and sold "factory fresh".
Ring of paper wrapped around the closed head of most cigars.
Portion of a tobacco leaf that holds the filler leaves together.
The mixture of different types of tobacco in a cigar, including up to five types
of filler leaves, a binder leaf and an outer wrapper.
Harmless white film caused by tobacco oils rising to the surface of the cigar
wrapper. Often indicates a strong taste. (Also called Plume).
Used to describe the smell of a fine cigar and fine wines.
Filler tobacco used to create the body of a cigar.
A circular piece of wrapper leaf used to secure the wrapper at the cigar
head.
Thin, three-inch cigars, popular in Europe, generally machine-made.
Draw
Amount of air that gets pulled through a lit cigar. Easy/hot or tight/plugged.
Flag
Instead of a cap, flags are an extension of the wrapper leaf used to finish
the head of a cigar. Sometimes tied off in a pigtail or a curly head.
Foot
The end of the cigar that you light. Often pre-cut.
Head
The closed end of the cigar that you put into your mouth.
Hot
A cigar draw that is too easy, often because it has been under-filled.
Hygrometer
Device used to measure humidity or percentage of moisture in the air.
Long Filler
Whole tobacco leaves used to fill a cigar; these leaves are long and can run
the length of the cigar's bunch. Long filler should burn evenly and consistently.
Piercer
Plug
Used to cut/pierce a small hole in the end of a cigar (also called a 'lance').
A blockage that prevents a cigar from drawing properly. (Gently massaging
the cigar may relieve a plugged draw).
Ring Gauge
Diameter of a cigar's barrel, expressed in 64ths of an inch. A half-inch cigar
would be a 32 ring (32/64).
Short Filler
Cigar bunch comprised of scraps of tobacco (parts of leaves and twigs).
Shoulder
Where the cap of the cigar meets the barrel. The cigar will unravel if cut.
Tunneling
Uneven burning of a cigar which occurs when a wrapper does not ash.
Wrapper
High-quality tobacco leaf wound around the finished bunch and binder.
7
Installation
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, or injury when using your appliance, follow
WARNING these basic precautions:

Read all instructions before using the appliance.
 DANGER or WARNING: An empty Wine Cooler and Cigar Humidor Center can be a hazardous for
children or small pets. If disposing of the cigar cooler humidor, remove gasket seals, latches, lids or the
entire door from your unused appliance, or take other action to ensure the appliance is harmless.

Never allow children to operate, play with, or crawl inside the appliance.

Never clean appliance parts with flammable fluids or harsh chemicals. The fumes can create a fire hazard or
explosion.

Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other appliance. The fumes can create a fire hazard or explosion.
BEFORE USING YOUR APPLIANCE
 Remove the exterior and interior packing.
 Clean the interior surface with lukewarm water using a soft cloth.
 You may see sticky blotches or glue-like residue on the cigar humidor, including the glass door, hydrometer or the Spanish Cedar wood. The sticky blotches or glue-like residue you see inside the cigar humidor is
from the oils in the Spanish Cedar wood. Spanish Cedar is naturally oily and it is in the oils where Spanish
Cedar gets the rich spicy aroma. Being a wood that naturally grows in the humid conditions of Central
America, the Spanish Cedar wood is naturally mold resistant, and resistant to the tobacco beetle.
 The natural oils can migrate to the surface of shelves or drawers and other parts of the humidor, such as
the door and humidity tray. These natural oils can be cleaned using alcohol. Although somewhat annoying,
the more oils in your Spanish Cedar wood, the more pleasing the aroma will be.
 Please be assured that no glue is being used in the manufacturing process of our Whynter cigar humidors.
SEASONING THE UNIT
 Before placing any cigars inside of the unit, please wipe the inside of the cabinet walls, drawers and
shelves with distilled water.
 This step is very important as cedar is a low density wood so the hydroscopicity is relatively large. Seasoning will allow the wood to absorb and hold moisture so that it does not absorb additional moisture once cigars are added.
INSTALLATION OF YOUR APPLIANCE
 The appliance is designed for a free standing installation.
 WARNING: Do not store or install the appliance outdoors.
 CAUTION: This appliance is designed for designed to storing and aging cigars . Do not store perishable
food, medicine or other medical products.
 Place your appliance on a hard and level floor that is strong enough to support it when it is fully loaded.
 To level your appliance, adjust the leveling legs at the bottom of the appliance if needed.
 When positioning the appliance, ensure that there is at least a 4” clearance at the sides and a 6” clearance
at the back. This will allow for adequate ventilation of any heat generated by appliance.
 We do not recommend installing the appliance on carpet.
 Do not install the appliance near an oven or other heating source. Direct sunlight may affect the acrylic
coating and heat sources may increase electrical consumption. For best performance, do not install the
appliance behind a cabinet door or block the base grille. Extreme cold ambient temperatures may also
cause the appliance not to perform properly.
 Avoid locating the appliance in area that may be exposed to excessive moisture.
 Plug in the appliance into an exclusive, grounded wall power outlet. Do not under any circumstances cut or
remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding
should be directed toward a qualified electrician or an authorized service center.
8
Installation
ELECTRICAL CONNECTION
WARNING: Improper use of the grounded plug can result in the risk of electrical shock.
If the power cord is damaged, have it replaced by a qualified electrician or contact
Whynter Service Department.
This appliance requires a standard 115/120 Volt AC ~/60Hz electrical ground outlet with three-prong.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly
grounded. The cord should be secured behind the appliance and not left exposed or dangling to prevent
accidental injury.
The appliance should always be plugged into its own individual electrical outlet which has a voltage rating
that matches the rating label on the appliance. This provides the best performance and also prevent overloading house wiring circuits that could cause a fire hazard from overheated. Never unplug the appliance
by pulling the power cord. Always grip the plug firmly and pull straight out from the receptacle. Repair or
replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord
that shows cracks or abrasion damage along its length or at either end. When moving the appliance, be
careful not to damage the power cord.
EXTENSION CORD
Because of potential safety hazards, it is strongly recommended that you do not use an extension cord
with this appliance. However, if you must use an extension cord, it is absolutely necessary that it be a
UL/CUL-Listed, 3-wire grounding type appliance extension cord having a grounding type plug and outlet
and that the electrical rating of the cord be 115 volts and at least 10 amperes.
BEFORE USING YOUR APPLIANCE
 Remove the exterior and interior packing.
 Clean the interior surface with lukewarm water using a soft cloth.
 Install the handle on the door
HANDLE BAR
To install the handles, you will need a Phillips head
screwdriver.
DOOR
SEAL
SCREWS
DOOR
HANDLE
BAR
1. Open the door.
2. Locate the two screw holes on the inside of the door
(they may be partially obscured by the door seal so
you may need to remove the door seal).
3. Insert the screws into the screw holes until they stick
out of the front of the door.
4. Line up the holes in the handle with the screws and
give each screw about 2-4 full turns into the handle
bar.
5. Now the turn the screws in all the way, and your handles are installed.
6. Replace seal into door frame.
9
Operation and Controls
It is recommended you install the appliance in a place where the ambient temperature is between 68º-80ºF.
If the ambient temperature is above or below recommended temperatures, the performance may be affected.
For example, placing your appliance in extreme cold or hot conditions may cause interior temperatures to
fluctuate.
SETTING THE TEMPERATURE
The interior temperature can be adjusted in increments of 1 degree. You can set the temperature by pressing the Up and Down buttons on the control panel.
 Keeping to a storage temperature of between 50°F - 66°F is essential for preserving the quality of cigars.
 Generally for red wines, the temperature range should be between 57°F-61°F. For white wines, the
temperature range should be 50°F-54°F, based on an ambient room temperature of 77°F.
INTERIOR LIGHT
You can turn on and off the interior light by pressing the “Light” button on the control panel.
LEVELING THE APPLIANCE
It is important for your appliance to be leveled in order to
work properly. It can be raised or lowered by rotating each
of the feet on the bottom of the machine. If you find that
the surface is not level, rotate the feet until the appliance
becomes level .You may need to make several adjustments to level it. We recommend using a carpenter’s level
to check the machine.
Note: This unit has 2 large levelling legs and 2 small levelling leg under the door hinge.
1. Place a carpenter’s level on top of the product to see if
the appliance is level from front to back and side to
side.
2. Adjust the height of the feet as follows: Turn the leveling feet to the right to lower that side of the refrigerator.
Turn the leveling feet to the left to raise that side of the
refrigerator.
UP
DOWN
HUMIDITY CONTROL
 This appliance is equipped with a system for maintaining the correct level of humidity. Fill the humidity tray
(small plastic reservoir) to about ¾ full with 100% distilled water, then place it onto the runners found on the
top shelf of the appliance. Check the water level regularly and refill as necessary.
 Please ensure the reservoir is positioned correctly on
the runners on the top shelf to avoid the possibility of
water spillage.
HYGROMETER
This unit is equipped with a hygrometer, which is a gauge used to measure humidity levels inside the humidor. It is recommended to maintain a humidity level of 62% to 75% inside of a humidor to properly preserve
and age cigars.
10
Operation and Controls
CIGAR CAPACITY
The listed cigar capacity for your cigar humidor is an estimated maximum capacity base on a standard five
inches long and a half an inch in diameter cigar. For other size cigars, the capacity will vary.
BOTTLE CAPACITY
The listed bottle capacity for your wine cooler is an estimated maximum capacity base on a standard 750ml
wine bottle. For other size bottles, the capacity will vary.
WINE SHELVES
The CWC-351DD wine cooler is equipped with 7 premium stainless steel trimmed scalloped shelves. If you
are having trouble fitting the stated listed number of bottles of wine in the wine cooler, try flipping the wine
racks over. To prevent damage to the door gasket, make sure the door is all the way opened when pulling
the shelves out.

For easy access of the wine bottles, you must pull the shelves approximately ⅓ out of the railing.

When removing the shelves out of the railing, make sure to remove all items first.

To remove the shelves, pull the shelf forward through the rail carefully.
TRANSPORT OF THE APPLIANCE
The ideal packaging for the wine cooler is its original packaging. Please keep the original packaging handy
and repack the wine cooler if you need to transport the unit.
OPERATING THE APPLIANCE
It is recommended you install the appliance in a place where the ambient temperature is between 68º-78ºF.
If the ambient temperature is above or below recommended temperatures, the performance may be affected. For example, placing your Wine Cooler in extreme cold or hot conditions may cause interior temperatures to fluctuate.
RECOMMENDED TEMPERATURE SETTINGS
Conservation
49 - 57ºF
Red Wines
58 - 72ºF
Dry/White Wines
48 - 57ºF
Rose Wines
49 - 51ºF
DEFROSTING
Under most ambient conditions, the wine cooler does not need to be defrosted. In cold ambient temperatures and/or high humidity, some frost may build up. To defrost, remove all items, unplug the wine cooler
and leave the door open. Never use a knife or other metal instrument to scrape ice/frost. After defrosting,
plug in the wine cooler and set the desired temperature.
11
Care and Maintenance
CAUTION: Failure to unplug the appliance could result in electric shock or personal injury
CLEANING YOUR APPLIANCE


Turn off the power, unplug the appliance, and remove all cigars from the appliance and store them in a
suitable place.
Clean the inside, the door seal and the inside of the glass with a clean, damp cloth.

Never use detergents or other substances that emit odors.

Always keep the door closed when cleaning the outside of the appliance. Make sure no detergent odors
penetrate into the appliance.

Clean the side panels and door surfaces with a clean and soft cloth. If necessary, use a moist cloth. Alternatively, use a microfiber cloth.

The humidity tray should be hand-washed with water and detergent. After cleaning, always make sure
the tray is thoroughly rinsed with clean water before replacing.
VACATION TIME

Short vacations: Leave the appliance operating during vacations of less than two days.

Long vacations: If the appliance will not be used for an extended period, remove all items and turn off
the appliance. Clean and dry the interior thoroughly.
MOVING YOUR APPLIANCE


Remove all items inside the appliance.
Securely tape down (we recommend using painter’s tape) all loose items (shelves) inside your appliance.

Turn the adjustable leg up to the base to avoid damage.


Tape (we recommend using painter’s tape) the door shut.
Be sure the appliance stays secure in the upright position during transportation and protect the exterior
of appliance with a blanket, or similar item.
PREPARING FOR STORAGE
If the appliance will not be used for a long time, or is to be
moved to another place, it will be necessary to defrost the unit
and dry the interior.
1. Disconnect the appliance from the power supply by removing the power plug from the wall socket.
2. Leave the door open to allow for air circulation and to prevent mold, mildew and unpleasant smells.
CAUTION: Store the unit out of the reach of children. If
you have children, you may want to take additional precautions such as removing the door to prevent a child from being trapped inside the appliance.
ENERGY SAVING TIPS

The appliance should be located in the coolest area of the room, away from heat producing appliances,
and out of any direct sunlight.

Ensure that the appliance is adequately ventilated. Never obstruct the air vents.

Close the door tightly and do not open the appliance too frequently or for a long period of time.

Store the content in an organized way.

Do not over-fill the appliance to allow air to circulate.
12
Troubleshooting
Problem
The appliance does not
operate
Possible Causes
Solutions
 There is a power failure.
 The appliance is not plugged in.
 A house fuse has blown or the circuit
 Ensure the appliance is plugged in and the pow-
 The appliance is placed too close to a heat
 Adjust the temperature.
er outlet has power.
 Replace the broken fuse or reset the breaker.
breaker is tripped.
The appliance is not
reaching the desired
temperature
Frost forming inside the
appliance
source
 The door is opened too often.
 Keep the appliance away from sunshine or other
heat sources.
 The door is not closed completely.
 Close the door tightly and do not open the door
 The door gasket does not seal properly.
 Ensure the door gasket is not loose..
 The environment is too humid.
 Although this unit uses an auto-defrost system,
 The ambient temperature is too low.
 The door is opened too frequently for a
long period of time.
too frequently or for a long period of time.
under certain conditions, manual defrosting may
required. If frost builds up, try running the cooler
on a warmer temperature setting.
 Close the door tightly and do not open the door
too frequently or for a long period of time.
 Unplug the unit to allow the frost to melt.
The appliance turns itself  The ambient (room) temperature is too low
on and off frequently
or high.
 A large amount of contents has been added to the appliance.
 The door is opened too often.
 The door is not closed completely.
 The door gasket does not seal properly.
 Decrease or increase the ambient (room) tem-
The appliance makes too  If the noise is from the fan, it may be normuch noise
mal operating noise.
 Contraction and expansion of the inside
walls may cause popping and crackling
noises.
 The appliance is not level.
 The fan makes normal fan noises.
The door does not close
properly
 The appliance is not level.
perature.
 To minimize internal temperature fluctuation, do
not add large amount of contents at once.
 Close the door tightly and do not open the door
too frequently or for a long period of time.
 Ensure the door gasket is not loose.
 Some popping or cracking noises are normal.
They are caused by expansion and contraction of
the inside walls due to temperature changes.
 Make sure the unit is on a hard and level surface. Do not place the appliance on carpet.
 Make sure the appliance is on a hard and level
 The door was reversed and not properly
surface. Avoid placing the appliance on a carpeted or soft surface.
 Reinstall door.
 The shelves are out of position .
 Correctly install the shelves.
Condensation builds up
on the glass door.
 Ambient temperature or humidity is high.
 Lower the room humidity by a dehumidifier or air
Frost forming inside the
appliance.
 Drawer(s) blocking internal fan.
 Move drawer(s) to the bottom portion of the ap-
 Items are blocking the internal fan.
 Move items so they do not block the fan.
Hygrometer reading is
off.
 Calibrate Analog Hygrometer
 Inside of a sealed plastic container, place a small
Sap/Oil spots can be
found on shelves and
drawers
 The sticky blotches or glue-like residue
 Spanish Cedar is naturally oily and it is in the oils
installed.
conditioner.
pliance
container filled with salt and a few drops of water, along with the hygrometer. After about 8
hours, the humidity inside of the container should
reach 75% humidity. Adjust the needle of the
hygrometer with a screwdriver on the back to
reflect 75%.
inside the cigar humidor is from the oils in
the Spanish Cedar wood.
13
where Spanish Cedar gets the rich spicy aroma.
Being a wood that naturally grows in the humid
conditions of Central America, the Spanish Cedar wood is naturally mold resistant, and resistant to the tobacco beetle.
 The natural oils can migrate to the surface of
shelves or drawers and other parts of the humidor, such as the door and humidity tray. These
natural oils can be cleaned using alcohol. Although somewhat annoying, the more oils in your
Spanish Cedar wood, the more pleasing the aroma will be.
ONE YEAR LIMITED WARRANTY
This WHYNTER Wine Cooler and Cigar Humidor Center is warranted, to the original owner
within the 48 continental states, for one year from the date of purchase against defects in material and workmanship under normal use and service. Should your WHYNTER Wine Cooler
and Cigar Humidor Center prove defective within one year from the date of purchase, return
the defective part or unit, freight prepaid (within two months of purchase; after two months to
one year, customer will be responsible for freight cost to Whynter’s service department),
along with an explanation of the claim to Whynter LLC. Please package the Wine Cooler and
Cigar Humidor Center carefully in its original packaging material to avoid damage in transit.
Please retain the original box and packaging material. Under this warranty, Whynter will repair or replace any parts found defective. This warranty is not transferable. After the expiration of the warranty, the cost of labor and parts will be the responsibility of the original owner
of the unit.
THIS WARRANTY DOES NOT COVER:
 Acts of God, such as fire, flood, hurricanes, earthquakes and torna-
does.
 Damage, accidental or otherwise, to the Wine Cooler and Cigar Hu-
midor Center while in the possession of a consumer not caused by a
defect in material or workmanship;
 Damage caused by consumer misuse, tampering, or failure to follow
the care and special handling provisions in the instructions.
 Damage to the finish of the case, or other appearance parts caused
by wear.
 Damage caused by repairs or alterations to the product by anyone
other than authorized by the manufacturer.
 Freight and Insurance cost for the warranty service.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR
REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD
ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. WHYNTER SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH
OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE- QUENTIAL DAMAGES, OR LIMITATIONS ON THE
DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM
STATE TO STATE.
Please retain the original proof of purchase in order to obtain warranty services.
Warranty begins from the original date of purchase.
To obtain service or information, contact
Whynter LLC via email at [email protected] or call
866-WHYNTER.
Product contents and specifications may change without notice.
Copyright © 2015 Whynter LLC
WWW.WHYNTER.COM
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement