KINO-9452 Mini-ITX SBC Page I
KINO-9452 Mini-ITX SBC
KINO-9452 Mini-ITX SBC
Page I
KINO-9452 Mini-ITX SBC
Revision
Date
Version
Changes
2008-07
v2.00
-Changed Northbridge chipset from Intel® 945GM to Intel® 945GME
-Changed to new manual format
-Changed 14-pin RS-232/422/485 serial port from COM2 to COM3
-Added three jumper information:
AT/ATX power mode select jumpers
LVDS screen resolution select jumper
COM3 mode select jumpers
2007-10
Page II
v1.00
Initial Release
KINO-9452 Mini-ITX SBC
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page III
KINO-9452 Mini-ITX SBC
Manual Conventions
WARNING!
Warnings appear where overlooked details may cause damage to the equipment or result
in personal injury. Warnings should be taken seriously. Warnings are easy to recognize.
The word “warning” is written as “WARNING,” both capitalized and bold and is followed by
text. The text is the warning message. A warning message is shown below:
WARNING:
This is an example of a warning message. Failure to adhere to warning
messages may result in permanent damage to the KINO-9452 or
personal injury to the user. Please take warning messages seriously.
CAUTION!
Cautionary messages should also be heeded to help reduce the chance of losing data or
damaging the KINO-9452. Cautions are easy to recognize. The word “caution” is written
as “CAUTION,” both capitalized and bold and is followed. The italicized text is the
cautionary message. A caution message is shown below:
Page IV
KINO-9452 Mini-ITX SBC
CAUTION:
This is an example of a caution message. Failure to adhere to cautions
messages may result in permanent damage to the KINO-9452. Please
take caution messages seriously.
NOTE:
These messages inform the reader of essential but non-critical information. These
messages should be read carefully as any directions or instructions contained therein can
help avoid making mistakes. Notes are easy to recognize. The word “note” is written as
“NOTE,” both capitalized and bold and is followed by text. The text is the cautionary
message. A note message is shown below:
NOTE:
This is an example of a note message. Notes should always be read.
Notes contain critical information about the KINO-9452. Please take
note messages seriously.
Page V
KINO-9452 Mini-ITX SBC
Packing List
NOTE:
If any of the components listed in the checklist below are missing,
please do not proceed with the installation. Contact the IEI reseller or
vendor you purchased the KINO-9452 from or contact an IEI sales
representative directly. To contact an IEI sales representative, please
send an email to [email protected]
The items listed below should all be included in the KINO-9452 package.
1 x KINO-9452 single board computer
1 x IDE flat cable
1 x HDTV cable
2 x SATA cables
1 x SATA power cable
1 x Dual RS-232 cable
1 x I/O shielding
1 x Mini jumper pack
1 x Utility CD
1 x Quick installation guide
Images of the above items are shown in Chapter 3.
Page VI
KINO-9452 Mini-ITX SBC
Table of Contents
1
INTRODUCTION..................................................................................................... 1
1.1 KINO-9452 OVERVIEW ............................................................................................. 2
1.1.1 KINO-9452 Benefits........................................................................................... 3
1.1.2 KINO-9452 Features.......................................................................................... 3
1.2 KINO-9452 BOARD OVERVIEW................................................................................. 4
1.2.1 KINO-9452 Connectors ..................................................................................... 4
1.2.2 Technical Specifications..................................................................................... 5
2
DETAILED SPECIFICATIONS ............................................................................. 8
2.1 OVERVIEW ................................................................................................................. 9
2.2 DIMENSIONS .............................................................................................................. 9
2.2.1 Board Dimensions.............................................................................................. 9
2.2.2 External Interface Panel Dimensions .............................................................. 10
2.3 DATA FLOW .............................................................................................................. 10
2.4 COMPATIBLE PROCESSORS ........................................................................................11
2.4.1 Compatible Processor Overview ......................................................................11
2.4.2 Supported Processors ...................................................................................... 12
2.5 INTEL® 945GME GRAPHICS AND MEMORY CONTROLLER HUB ............................... 13
2.5.1 Intel® 945GME Overview ................................................................................ 13
2.5.2 Intel® 945GME Front Side Bus (FSB) Support .............................................. 13
2.5.3 Intel® 945GME Memory Support..................................................................... 14
2.5.4 Intel® 945GME Integrated Graphics ............................................................... 15
2.5.4.1 Intel® 945GME Analog CRT Support....................................................... 15
2.5.4.2 Intel® 945GME LVDS Support................................................................. 16
2.5.4.3 Intel® 945GME TV Out Support .............................................................. 16
2.5.5 Intel® 945GME Direct Media Interface (DMI)................................................ 16
2.6 INTEL® ICH7-M I/O CONTROLLER HUB.................................................................. 17
2.6.1 Intel® ICH7-M Overview ................................................................................. 17
2.6.2 Intel® ICH7-M HD Audio Controller............................................................... 17
2.6.3 Intel® ICH7-M PCIe Bus: PCIe GbE Ethernet Controller .............................. 18
2.6.4 Intel® ICH7-M IDE Interface........................................................................... 19
Page VII
KINO-9452 Mini-ITX SBC
2.6.5 Intel® ICH7-M Low Pin Count (LPC) Interface .............................................. 20
2.6.6 Intel® ICH7-M PCI Interface........................................................................... 20
2.6.7 Intel® ICH7-M Real Time Clock ...................................................................... 21
2.6.8 Intel® ICH7-M SATA Controller ...................................................................... 21
2.6.9 Intel® ICH7-M USB Controller........................................................................ 21
2.7 PCIE BUS COMPONENTS .......................................................................................... 22
2.7.1 PCIe Bus Overview .......................................................................................... 22
2.7.2 Broadcom PCI Express GbE interface............................................................. 22
2.8 LPC BUS COMPONENTS ........................................................................................... 23
2.8.1 LPC Bus Overview........................................................................................... 23
2.8.2 BIOS Chipset.................................................................................................... 23
2.8.3 Super I/O chipset.............................................................................................. 23
2.8.3.1 Super I/O LPC Interface ........................................................................... 24
2.8.3.2 Super I/O 16C550 UARTs ........................................................................ 24
2.8.3.3 Super I/O Enhanced Hardware Monitor ................................................... 24
2.8.3.4 Super I/O Fan Speed Controller................................................................ 24
2.8.3.5 Super I/O Keyboard Controller................................................................. 25
2.8.4 Fintek F81216DG LPC Serial Port Chipset.................................................... 25
2.9 ENVIRONMENTAL AND POWER SPECIFICATIONS ....................................................... 25
2.9.1 System Monitoring ........................................................................................... 25
2.9.2 Operating Temperature and Temperature Control........................................... 26
2.9.3 Power Consumption......................................................................................... 26
3
UNPACKING .......................................................................................................... 28
3.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 29
3.2 UNPACKING.............................................................................................................. 29
3.2.1 Unpacking Precautions.................................................................................... 29
3.3 UNPACKING CHECKLIST ........................................................................................... 30
3.3.1 Package Contents............................................................................................. 30
3.3.2 Optional Items.................................................................................................. 31
4
CONNECTORS AND JUMPERS ......................................................................... 33
4.1 PERIPHERAL INTERFACE CONNECTORS .................................................................... 34
4.1.1 KINO-9452 Layout........................................................................................... 34
4.1.2 Peripheral Interface Connectors ..................................................................... 35
Page VIII
KINO-9452 Mini-ITX SBC
4.1.3 Rear Panel Connectors .................................................................................... 36
4.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 37
4.2.1 Audio Connector .............................................................................................. 37
4.2.2 Fan Connectors................................................................................................ 38
4.2.3 Front Panel Connector .................................................................................... 39
4.2.4 Digital Input/Output Connector....................................................................... 40
4.2.5 IDE Connector ................................................................................................. 41
4.2.6 LCD Backlight Connector................................................................................ 42
4.2.7 LVDS LCD connector ...................................................................................... 43
4.2.8 Mini PCI Slot ................................................................................................... 45
4.2.9 Power Connector ............................................................................................. 46
4.2.10 14-Pin Serial Port Connectors....................................................................... 47
4.2.11 10-Pin Serial Port Connectors....................................................................... 48
4.2.12 SATA Drive Connectors ................................................................................. 49
4.2.13 SPDIF Connector........................................................................................... 50
4.2.14 Internal USB Connectors............................................................................... 51
4.3 EXTERNAL INTERFACE CONNECTORS ....................................................................... 52
4.3.1 Audio Connectors............................................................................................. 53
4.3.2 CRT Connector ................................................................................................ 54
4.3.3 Ethernet Connectors ........................................................................................ 55
4.3.4 Keyboard/Mouse Connector ............................................................................ 56
4.3.5 Serial Port Connectors .................................................................................... 57
4.3.6 TV-Out Connector ............................................................................................ 58
4.3.7 USB Connector ................................................................................................ 59
5
INSTALLATION .................................................................................................... 60
5.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 61
5.2 INSTALLATION CONSIDERATIONS ............................................................................. 62
5.2.1 Installation Notices .......................................................................................... 62
5.2.2 Installation Checklist ....................................................................................... 63
5.3 CPU, CPU COOLING KIT AND DIMM INSTALLATION ............................................. 64
5.3.1 Socket 479 CPU Installation............................................................................ 64
5.3.2 Cooling Kit CF-479B-RS Installation.............................................................. 66
5.3.3 DIMM Installation ........................................................................................... 68
5.4 JUMPER SETTINGS .................................................................................................... 70
Page IX
KINO-9452 Mini-ITX SBC
5.4.1 AT/ATX Power Select Jumper Settings ............................................................ 70
5.4.2 Clear CMOS Jumper........................................................................................ 72
5.4.3 COM 3 Function Select Jumper....................................................................... 73
5.4.4 LVDS Screen Resolution Selection................................................................... 74
5.4.5 LVDS Voltage Selection.................................................................................... 76
5.5 CHASSIS INSTALLATION ........................................................................................... 77
5.5.1 Airflow.............................................................................................................. 77
5.5.2 Motherboard Installation................................................................................. 78
5.6 INTERNAL PERIPHERAL DEVICE CONNECTIONS........................................................ 78
5.6.1 Peripheral Device Cables ................................................................................ 78
5.6.2 IDE Cable Connection..................................................................................... 79
5.6.3 Dual RS-232 Cable Connection....................................................................... 80
5.6.4 SATA Drive Connection ................................................................................... 81
5.7 EXTERNAL PERIPHERAL INTERFACE CONNECTION ................................................... 82
5.7.1 Audio Connection............................................................................................. 83
5.7.2 RJ-45 Ethernet and USB Connection .............................................................. 83
5.7.3 VGA Monitor Connection ................................................................................ 84
5.7.4 Serial Device Connection ................................................................................ 85
5.7.5 PS/2 Keyboard/Mouse Connection .................................................................. 86
5.7.6 HDTV Cable Connection ................................................................................. 87
6
AMI BIOS................................................................................................................ 89
6.1 INTRODUCTION ........................................................................................................ 90
6.1.1 Starting Setup................................................................................................... 90
6.1.2 Using Setup ...................................................................................................... 90
6.1.3 Getting Help..................................................................................................... 91
6.1.4 Unable to Reboot after Configuration Changes .............................................. 91
6.1.5 BIOS Menu Bar................................................................................................ 91
6.2 MAIN ....................................................................................................................... 91
6.3 ADVANCED ............................................................................................................... 93
6.3.1 CPU Configuration.......................................................................................... 94
6.3.2 IDE Configuration ........................................................................................... 95
6.3.2.1 IDE Master, IDE Slave ............................................................................. 97
6.3.3 Super IO Configuration.................................................................................. 101
6.3.4 Hardware Health Configuration.................................................................... 104
Page X
KINO-9452 Mini-ITX SBC
6.3.5 Power Configuration...................................................................................... 106
6.3.5.1 ACPI Configuration ................................................................................ 107
6.3.5.2 APM Configuration................................................................................. 108
6.3.6 Remote Access Configuration .........................................................................110
6.3.7 USB Configuration..........................................................................................112
6.4 PCI/PNP .................................................................................................................114
6.5 BOOT ......................................................................................................................116
6.5.1 Boot Settings Configuration............................................................................117
6.6 SECURITY............................................................................................................... 120
6.7 CHIPSET ................................................................................................................. 121
6.7.1 North Bridge Configuration........................................................................... 122
6.7.2 South Bridge Configuration........................................................................... 126
6.8 EXIT ....................................................................................................................... 128
7
SOFTWARE DRIVER ......................................................................................... 130
7.1 AVAILABLE SOFTWARE DRIVERS ............................................................................ 131
7.2 CHIPSET DRIVER INSTALLATION............................................................................. 131
7.3 VGA DRIVER ......................................................................................................... 134
7.4 BROADCOM LAN DRIVER (FOR GBE LAN) INSTALLATION .................................. 138
7.5 REALTEK HD AUDIO DRIVER (ALC883) INSTALLATION ....................................... 143
7.6 INTEL MATRIX STORAGE MANAGER INSTALLATION ............................................... 148
A
BIOS CONFIGURATION OPTIONS ............................................................. 151
A.1 BIOS CONFIGURATION OPTIONS........................................................................... 152
B
DIO INTERFACE................................................................................................. 155
B.1 DIO INTERFACE INTRODUCTION ........................................................................... 156
B.2 DIO CONNECTOR PINOUTS ................................................................................... 156
B.3 ASSEMBLY LANGUAGE SAMPLES ........................................................................... 157
B.3.1 Enable the DIO Input Function..................................................................... 157
B.3.2 Enable the DIO Output Function .................................................................. 157
C
WATCHDOG TIMER .......................................................................................... 158
D
ADDRESS MAPPING.......................................................................................... 161
D.1 IO ADDRESS MAP ................................................................................................. 162
D.2 1ST MB MEMORY ADDRESS MAP ......................................................................... 162
Page XI
KINO-9452 Mini-ITX SBC
D.3 IRQ MAPPING TABLE ............................................................................................ 163
D.4 DMA CHANNEL ASSIGNMENTS ............................................................................. 163
E
COMPATIBILITY................................................................................................ 164
E.1 COMPATIBLE PROCESSORS ..................................................................................... 165
E.2 COMPATIBLE MEMORY MODULES.......................................................................... 166
F
HAZARDOUS MATERIALS DISCLOSURE ................................................... 167
F.1 HAZARDOUS MATERIAL DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ..................................... 168
G
EXTERNAL AC’97 AUDIO CODEC ................................................................. 171
G.1 INTRODUCTION ...................................................................................................... 172
G.1.1 Accessing the AC’97 CODEC ....................................................................... 172
G.1.2 Driver Installation ......................................................................................... 172
G.2 SOUND EFFECT CONFIGURATION ........................................................................... 173
G.2.1 Accessing the Sound Effects Manager........................................................... 173
G.2.2 Sound Effect Manager Configuration Options .............................................. 174
H
INDEX.................................................................................................................... 177
Page XII
KINO-9452 Mini-ITX SBC
List of Figures
Figure 1-1: KINO-9452 Embedded SBC.......................................................................2
Figure 1-2: KINO-9452 Board Overview (Top View)...................................................4
Figure 2-1: KINO-9452 Dimensions (mm) ...................................................................9
Figure 2-2: External Interface Panel Dimensions (mm)...........................................10
Figure 2-3: Data Flow Block Diagram........................................................................11
Figure 2-4: Front Side Bus (FSB)...............................................................................13
Figure 2-5: 240-pin DDR2 DIMM Sockets ..................................................................14
Figure 2-6: Integrated Graphics Interfaces...............................................................15
Figure 2-7: HD Audio Codec ......................................................................................18
Figure 2-8: PCIe GbE Connectors .............................................................................19
Figure 2-9: Mini PCI Slot .............................................................................................20
Figure 2-10: Onboard USB Implementation .............................................................22
Figure 4-1: Connector and Jumper Locations .........................................................34
Figure 4-2: Audio Connector Location......................................................................37
Figure 4-3: Fan Connector Locations .......................................................................38
Figure 4-4: Front Panel Connector Location............................................................39
Figure 4-5: GPIO Connector Location.......................................................................40
Figure 4-6: IDE Device Connector Location .............................................................41
Figure 4-7: LCD Backlight Connector Location .......................................................43
Figure 4-8: LVDS LCD Connector Location..............................................................44
Figure 4-9: Mini PCI Slot Location.............................................................................45
Figure 4-10: Power Connector Location ...................................................................47
Figure 4-11: 14-Pin Serial Port Connector Locations..............................................48
Figure 4-12: 10-Pin Serial Port Connector Locations..............................................49
Figure 4-13: SATA Drive Connector Locations........................................................50
Figure 4-14: SPDIF Connector Locations .................................................................51
Figure 4-15: Internal USB Connector Locations ......................................................52
Page XIII
KINO-9452 Mini-ITX SBC
Figure 4-16: KINO-9452 External Interface Connectors ..........................................53
Figure 4-17: Audio Connectors..................................................................................54
Figure 4-18: VGA Connector ......................................................................................54
Figure 4-19: RJ-45 Ethernet Connector ....................................................................55
Figure 4-20: PS/2 Pinouts...........................................................................................56
Figure 4-21: External Serial Port Connector ............................................................57
Figure 4-22: TV-Out Connector..................................................................................58
Figure 5-1: Make sure the CPU socket retention screw is unlocked .....................65
Figure 5-2: Lock the CPU Socket Retention Screw .................................................66
Figure 5-3: IEI CF-479B-RS Cooling Kit ....................................................................66
Figure 5-4: Cooling Kit Support Bracket...................................................................67
Figure 5-5: Connect the cooling fan cable ...............................................................68
Figure 5-6: Installing a DIMM .....................................................................................69
Figure 5-7: Jumper Locations....................................................................................70
Figure 5-8: AT/ATX Power Select Jumper Location ................................................71
Figure 5-9: Clear CMOS Jumper ................................................................................73
Figure 5-10: COM 3 Function Select Jumper Location ...........................................74
Figure 5-11: LVDS Screen Resolution Selection Jumper Pinout Locations .........75
Figure 5-12: LVDS Voltage Selection Jumper Pinout Locations............................77
Figure 5-13: IDE Cable Connection ...........................................................................79
Figure 5-14: Dual RS-232 Cable Installation.............................................................80
Figure 5-15: SATA Drive Cable Connection .............................................................81
Figure 5-16: SATA Power Drive Connection ............................................................82
Figure 5-17: Audio Connectors..................................................................................83
Figure 5-18: RJ-45 Ethernet Connector ....................................................................84
Figure 5-19: VGA Connector ......................................................................................85
Figure 5-20: Serial Device Connector .......................................................................86
Figure 5-21: PS/2 Keyboard/Mouse Connector........................................................87
Figure 5-22: HDTV Cable Connector .........................................................................88
Figure 7-1: InstallShield Wizard Preparation Screen............................................ 132
Figure 7-2: Welcome Screen ................................................................................... 132
Figure 7-3: License Agreement............................................................................... 133
Page XIV
KINO-9452 Mini-ITX SBC
Figure 7-4: Readme Information ............................................................................. 133
Figure 7-5: Restart the Computer ........................................................................... 134
Figure 7-6: Starting Install Shield Wizard Screen ................................................. 135
Figure 7-7: Preparing Setup Screen ....................................................................... 135
Figure 7-8: VGA Driver Installation Welcome Screen........................................... 136
Figure 7-9: VGA Driver License Agreement .......................................................... 136
Figure 7-10: VGA Driver Installing Notice.............................................................. 137
Figure 7-11: VGA Driver Installation Complete ..................................................... 137
Figure 7-12: Access Windows Control Panel........................................................ 138
Figure 7-13: Double Click the System Icon ........................................................... 139
Figure 7-14: Double Click the Device Manager Tab.............................................. 139
Figure 7-15: Device Manager List ........................................................................... 140
Figure 7-16: Search for Suitable Driver.................................................................. 141
Figure 7-17: Locate Driver Files.............................................................................. 142
Figure 7-18: Location Browsing Window............................................................... 142
Figure 7-19: Access Windows Control Panel........................................................ 143
Figure 7-20: Double Click the System Icon ........................................................... 144
Figure 7-21: Double Click the Device Manager Tab.............................................. 145
Figure 7-22: Device Manager List ........................................................................... 146
Figure 7-23: Search for Suitable Driver.................................................................. 147
Figure 7-24: Locate Driver Files.............................................................................. 148
Figure 7-25: Preparing Setup Screen ..................................................................... 149
Page XV
KINO-9452 Mini-ITX SBC
List of Tables
Table 1-1: Technical Specifications ............................................................................7
Table 2-1: Processor Features...................................................................................12
Table 2-2: Supported Processors..............................................................................12
Table 2-3: Supported HDD Specifications ................................................................19
Table 2-4: Power Consumption .................................................................................27
Table 3-1: Package List Contents..............................................................................31
Table 3-2: Optional Items ...........................................................................................32
Table 4-1: Peripheral Interface Connectors..............................................................36
Table 4-2: Rear Panel Connectors.............................................................................36
Table 4-3: Audio Connector Pinouts .........................................................................37
Table 4-4: Fan Connector Pinouts.............................................................................38
Table 4-5: Front Panel Connector Pinouts ...............................................................40
Table 4-6: GPIO Connector Pinouts ..........................................................................41
Table 4-7: IDE Connector Pinouts .............................................................................42
Table 4-8: LCD Backlight Connector Pinouts ..........................................................43
Table 4-9: LVDS LCD Connector Pinouts .................................................................44
Table 4-10: Mini PCI Slot Pinouts ..............................................................................46
Table 4-11: Power Connector Pinouts ......................................................................47
Table 4-12: COM3 Pinouts..........................................................................................48
Table 4-13: COM2 and COM4 Pinouts .......................................................................49
Table 4-14: SATA Drive Connector Pinouts .............................................................50
Table 4-15: SPDIF Pinouts..........................................................................................51
Table 4-16: USB3 and USB4 Pinouts.........................................................................52
Table 4-17: VGA Connector Pinouts .........................................................................55
Table 4-18: LAN1 and LAN2 Pinouts .........................................................................55
Table 4-19: RJ-45 Ethernet Connector LEDs............................................................56
Table 4-20: PS/2 Connector Pinouts .........................................................................57
Table 4-21: External Serial Port Pinouts ...................................................................58
Page XVI
KINO-9452 Mini-ITX SBC
Table 4-22: TV-Out Pinouts ........................................................................................59
Table 4-23: External USB Connector Pinouts ..........................................................59
Table 5-1: Jumpers......................................................................................................70
Table 5-2: AT/ATX Power Select Jumper Settings...................................................71
Table 5-3: Clear CMOS Jumper Settings ..................................................................72
Table 5-4: COM 3 Function Select Jumper Settings................................................74
Table 5-5: LVDS Screen Resolution Selection Jumper Settings............................75
Table 5-6: LVDS Voltage Selection Jumper Settings ..............................................76
Table 5-7: IEI Provided Cables...................................................................................78
Table 6-1: BIOS Navigation Keys...............................................................................91
Page XVII
KINO-9452 Mini-ITX SBC
List of BIOS Menus
BIOS Menu 1: Main 92
BIOS Menu 2: Advanced.............................................................................................94
BIOS Menu 3: CPU Configuration..............................................................................95
BIOS Menu 4: IDE Configuration ...............................................................................96
BIOS Menu 5: IDE Master and IDE Slave Configuration..........................................98
BIOS Menu 6: Super IO Configuration ................................................................... 102
BIOS Menu 7: Hardware Health Configuration...................................................... 104
BIOS Menu 8: Power Configuration ....................................................................... 106
BIOS Menu 9: General ACPI Configuration [Advanced\ ACPI Configuration] ... 107
BIOS Menu 10: APM Configuration ........................................................................ 108
BIOS Menu 11: Remote Access Configuration [Advanced] ................................ 111
BIOS Menu 12: USB Configuration......................................................................... 112
BIOS Menu 13: PCI/PnP Configuration .................................................................. 115
BIOS Menu 14: Boot................................................................................................. 117
BIOS Menu 15: Boot Settings Configuration......................................................... 118
BIOS Menu 16: Security........................................................................................... 120
BIOS Menu 17: Chipset............................................................................................ 122
BIOS Menu 18: North Bridge Chipset Configuration............................................ 123
BIOS Menu 19:South Bridge Chipset Configuration ............................................ 127
BIOS Menu 20:Exit ................................................................................................... 128
Page XVIII
KINO-9452 Mini-ITX SBC
Chapter
1
1 Introduction
Page 1
KINO-9452 Mini-ITX SBC
1.1 KINO-9452 Overview
Figure 1-1: KINO-9452 Embedded SBC
The KINO-9452 Mini-ITX form factor motherboard is an Intel® dual-core CPU platform.
Intel® Core™2 Duo, Core Duo and Core Solo CPU are all supported to enhance the
system processing speed. The KINO-9452 has a maximum front side bus (FSB)
frequency of 667 MHz and contains two DDR2 SDRAM DIMM sockets that support up to
4 GB system memory.
The KINO-9452 supports two audio streams through the High Definition (HD) audio codec
and supports diverse displays including one VGA display, one HDTV display and one
LVDS display. These multimedia features make the KINO-9452 a best choice for
integrating into point-of-sale (POS), kiosk or digital signage applications.
The KINO-9452 supports up to two serial ATA (SATA) hard disk drives (HDD) with
maximum transfer rates of 1.5 Gb/s and up to eight USB 2.0 devices. The dual PCI
Express (PCIe) Gigabit Ethernet (GbE) controllers provide GbE connectivity for network
communication. The KINO-9452 also has a PCI socket and a Mini PCI socket for system
expansion. Three RS-232, one RS-232/422/485 and one digital input/output (DIO) port
offer system integrators more choices of peripheral devices for the targeted application.
Page 2
KINO-9452 Mini-ITX SBC
1.1.1 KINO-9452 Benefits
Some of the KINO-9452 benefits include:
Dual core Intel® processor support
o
o
Two physical cores in a package share the system load
Each core has its own L1 cache and shares the L2 cache to enhance the
processing speed
o
High performance levels especially in 3D graphic and multi media
application
Independent dual audio with HDTV output
Excellent thermal control that enhance voltage efficiency and supports cooler
and quieter systems
Expansion slots and rich I/O interface
o
o
Integrates a PCI and a mini PCI slot for flexible expansion capabilities
Integrates TV-out and multi channel audio for related applications
DDR2 memory technology supported
SATA with 1.5 Gb/s transfer rate
Dual PCIe GbE enhance high performance in network
1.1.2 KINO-9452 Features
Some of the KINO-9452 features are listed below:
Complies with RoHS
Supports Intel® Core™2 Duo, Core™ Duo, Core™ Solo and Celeron® M
processor
Supports a maximum FSB speed up to 667 MHz
Two 240-pin 400 MHz, 533 MHz or 667 MHz DDR2 SDRAM DIMMs
supported (system max. 4 GB)
Comes with dual Broadcom BCM5787 PCIe GbE controllers
Supports two SATA channels with transfer rates up to 1.5 Gb/s
Supports eight USB 2.0 devices
Supports HDTV-Out, dual-channel 18-bit or 24-bit LVDS and CRT
Page 3
KINO-9452 Mini-ITX SBC
1.2 KINO-9452 Board Overview
Figure 1-2: KINO-9452 Board Overview (Top View)
1.2.1 KINO-9452 Connectors
The KINO-9452 has the following connectors on-board:
2 x DDR2 DIMM sockets
1 x Digital I/O connector
3 x Fan connectors
1 x Front panel audio connector
1 x Front panel connector
1 x IDE Interface connector
1 x LCD backlight connector
1 x LVDS LCD connector
Page 4
KINO-9452 Mini-ITX SBC
1 x Mini PCI slot
1 x PCI slot
1 x Power connector
3 x Serial port connectors
2 x SATA connectors
1 x SPDIF connector
2 x USB connectors
The KINO-9452 has the following connectors on the board rear panel:
6 x Audio jacks
1 x CRT connector
2 x Ethernet connectors
2 x Keyboard/Mouse connectors
1 x Serial port connector
1 x TV-Out port
4 x USB 2.0 ports
The KINO-9452 has the following on-board jumpers:
AT/ATX power mode selection
Clear CMOS
COM3 mode selection (RS-232/422/485)
LVDS LCD voltage selection
LVDS screen resolution selection
The location of these connectors on the motherboard can be seen in Figure 1-1. These
connectors are fully described in Chapter 3.
1.2.2 Technical Specifications
KINO-9452 technical specifications are listed in Table 1-1. Detailed descriptions of each
specification can be found in Chapter 2.
Page 5
KINO-9452 Mini-ITX SBC
SPECIFICATION
CPUs Supported
Intel® Core™2 Duo/ Core™ Duo/Core™
Solo/Celeron® M with 533 MHz or 667 MHz FSB
Chipsets
Northbridge: Intel® 945GME
Southbridge: Intel® ICH7-M
Graphics Support
Display
Intel Gen 3.5 Integrated Graphics Engine
CRT
HDTV:
Overscaling / Component, S-Video and Composite
output
480P / 720P / 1080i / 1080P and NTSC / PAL
support
LVDS: Dual channel 18-bit or 24-bit LVDS
Memory
Two 240-pin 400/533/667 MHz 2 GB DDR2 SDRAM
DIMMs (system max. 4 GB)
PCI Bus Interface
33 MHz, Revision 2.3
Serial ATA (SATA)
Two SATA connectors with 1.5 Gb/s transfer rates
HDD Interface
One IDE channel supports two Ultra ATA 100/66/33
devices
USB Interfaces
Eight USB 2.0 connectors supported
Serial Ports
Four COM ports
Extension
One Mini PCI slot
One PCI slot
Super I/O
iTE IT8712
Digital I/O
8-bit digital I/O, 4 input / 4 output by super I/O
Audio
RealTek ALC883 with 7.1 channel HD interface with 2
audio streams support
Page 6
KINO-9452 Mini-ITX SBC
Ethernet
Dual Broadcom BCM5787 PCIe GbE controllers with
ASF2.0 remote control support
BIOS
AMI BIOS Label
Power
AT/ATX power
Physical Dimensions
170 mm x 170 mm
Operating Temperature
Minimum: 0ºC (32°F)
Maximum: 60°C (140°F)
Table 1-1: Technical Specifications
Page 7
KINO-9452 Mini-ITX SBC
Chapter
2
2 Detailed Specifications
Page 8
KINO-9452 Mini-ITX SBC
2.1 Overview
This chapter describes the specifications and on-board features of the KINO-9452 in
detail.
2.2 Dimensions
2.2.1 Board Dimensions
The dimensions of the board are listed below:
Length:
170 mm
Width:
170 mm
Figure 2-1: KINO-9452 Dimensions (mm)
Page 9
KINO-9452 Mini-ITX SBC
2.2.2 External Interface Panel Dimensions
External peripheral interface connector panel dimensions are shown in Figure 2-2.
Figure 2-2: External Interface Panel Dimensions (mm)
2.3 Data Flow
The KINO-9452 motherboard comes with an Intel® 945GME GMCH and an Intel®
ICH7-M I/O Controller Hub. Figure 2-3 shows the data flow between the system chipset,
the CPU and other components installed on the motherboard.
Page 10
KINO-9452 Mini-ITX SBC
Figure 2-3: Data Flow Block Diagram
2.4 Compatible Processors
2.4.1 Compatible Processor Overview
The KINO-9452 supports the following socket 479 processors:
Intel® Core™2 Duo Mobile processors
Intel® Core™ Duo processors
Page 11
KINO-9452 Mini-ITX SBC
Intel® Core™ Solo processors
Intel® Celeron® M processors
The first three of the above processors communicate with the Intel® 945GME GMCH
through a 667 MHz FSB and the Intel® Celeron® M processor through a 533 MHz FSB.
Features of the supported processors are listed in Table 2-1.
CPU Features
Core™2 Duo
Core™ Duo
Core™ Solo
Celeron® M
Dual core
Yes
Yes
No
No
Enhanced Halt State (C1E)
No
Yes
No
No
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
EM64T
Yes
No
No
No
Virtualization Technology
Yes
Yes
No
No
Enhanced Intel
®
®
Speedstep
Technolgy
Execute Disable Bit
®
Intel
®
Intel
Table 2-1: Processor Features
2.4.2 Supported Processors
Specifications for the compatible processors are listed in Table 2-2 below:
Family
Core™2 Duo Mobile
sSpec# CPU Speed Processor # Bus Speed
Mfg Tech
Stepping
Cache Size
SL9SJ
2.33 GHz
T7600
667 MHz
65 nm
B2
4 MB
SL9SK
2.16 GHz
T7400
667 MHz
65 nm
B2
4 MB
SL9SL
2 GHz
T7200
667 MHz
65 nm
B2
4 MB
SL9SP
1.83 GHz
T5600
667 MHz
65 nm
B2
2 MB
SL9SQ
1.66 GHz
T5500
667 MHz
65 nm
B2
2 MB
SL8VT
2 GHz
T2500
667 MHz
65 nm
C0
2 MB
SL9DN
1.66 GHz
T2300E
667 MHz
65 nm
C0
2 MB
Core™ Solo
SL92X
1.83 GHz
T1400
667 MHz
65 nm
C0
2 MB
Celeron® M
SL9VA
1.73 GHz
530
533 MHz
65 nm
A1
1 MB
SL9LF
1.86 GHz
440
533 MHz
65 nm
D0
1 MB
Core™ Duo
Table 2-2: Supported Processors
Page 12
KINO-9452 Mini-ITX SBC
2.5 Intel® 945GME Graphics and Memory Controller Hub
2.5.1 Intel® 945GME Overview
The Intel® 945GME GMCH has the Generation 3.1 Intel Integrated Graphics Engine and
the Intel® Graphics Media Accelerator 950 (Intel® GMA 950). The integrated graphics and
memory controller hub (GMCH) facilitates the flow of information primarily between the
following four interfaces:
Front Side Bus (FSB)
System Memory Interface
Graphics Interface
Direct Media Interface (DMI)
2.5.2 Intel® 945GME Front Side Bus (FSB) Support
The Intel® 945GME GMCH supports processors with the following FSB speeds:
533 MHz
667 MHz
The Socket 478, Intel® 945GME GMCH and the FSB are shown in Figure 2-4.
Figure 2-4: Front Side Bus (FSB)
Page 13
KINO-9452 Mini-ITX SBC
2.5.3 Intel® 945GME Memory Support
WARNING:
Only DDR2 memory module can be installed on the KINO-9452. Do not
install DDR memory modules. If a DDR memory module is installed on
the KINO-9452, the KINO-9452 may be irreparably damaged.
The Intel® 945GME GMCH on the KINO-9452 supports two 240-pin DDR2 DIMMs with the
following features:
Two 240-pin DIMMs
DDR2 only (DO NOT install a DDR DIMM)
Single-channel or dual-channel
Capacities of 256 MB, 512 MB, 1 GB or 2 GB
Transfer speeds of 400 MHz, 533 MHz or 667 MHz
64-bit wide channel
The memory sockets are shown in Figure 2-5.
Figure 2-5: 240-pin DDR2 DIMM Sockets
Page 14
KINO-9452 Mini-ITX SBC
2.5.4 Intel® 945GME Integrated Graphics
The Intel® 945GME GMCH has an Intel® Gen. 3.5 integrated graphics engine that
supports the following display devices:
Analog CRT
LVDS
TV-Out
Figure 2-6: Integrated Graphics Interfaces
2.5.4.1 Intel® 945GME Analog CRT Support
A DB-15 VGA connector on the external peripheral interface connector panel is interfaced
to the Intel® 945GME graphics engine. The Intel® 945GME internal graphics engine, with
an integrated 400 MHz RAMDAC and hot plug CRT support, supports analog CRT
monitors up to QXGA.
Page 15
KINO-9452 Mini-ITX SBC
2.5.4.2 Intel® 945GME LVDS Support
A 30-pin LVDS crimp connector is interfaced to the Intel® 945GME graphics engine. The
Intel® 945GME internal graphics engine supports LVDS displays with the following
features:
Up to UXGA monitors with a maximum resolution of 1600 x 1200
18-bit or 24-bit 25 MHz to 112 MHz single-channel or dual-channel LVDS
screens
CPIS 1.5 compliant LVDS screens
2.5.4.3 Intel® 945GME TV Out Support
An external 7-pin DIN TV output connector is interfaced to the Intel® 945GME graphics
engine. The Intel® 945GME internal graphics engine has the following TV output features:
Three integrated 10-bit DACs
Overscaling
NTSC and PAL formats supported
Supports RCA or S-VIDEO connectivity
Supports HDTV with the following resolutions:
o
o
o
o
480p
720p
1080i
1080p
2.5.5 Intel® 945GME Direct Media Interface (DMI)
Intel® 945GME GMCH is connected to the Intel® ICH7-M through the chip-to-chip Direct
Media Interface (DMI). Features of the Intel® 945GME DMI are listed below:
2 GB/s (1 GB/s in each direction) bus speed
32-bit downstream address
Page 16
KINO-9452 Mini-ITX SBC
2.6 Intel® ICH7-M I/O Controller Hub
2.6.1 Intel® ICH7-M Overview
The Intel® ICH7-M I/O Controller Hub (ICH) is connected to the Intel® 945GME GMCH
through the chip-to-chip Direct Media Interface (DMI). Some of the features of the Intel®
ICH7-M are listed below.
Complies with PCI Express Base Specification, Revision 1.0a
Complies with PCI Local Bus Specification, Revision 2.3 and supports
33 MHz PCI operations
Supports ACPI Power Management Logic
Contains:
o
o
o
Enhanced DMA controller
Interrupt controller
Timer functions
Integrated SATA host controller with DMA operations interfaced to two SATA
connectors on the KINO-9452
Integrated IDE controller supports Ultra ATA 100/66/33
Supports the eight USB 2.0 devices on the KINO-9452 with four UHCI
controllers and one EHCI controller
Complies with System Management Bus (SMBus) Specification, Version 2.0
Supports Audio Codec ’97 (AC’97) Revision 2.3
Supports Intel® High Definition Audio
Contains Low Pin Count (LPC) interface
Supports Firmware Hub (FWH) interface
Serial peripheral interface support
2.6.2 Intel® ICH7-M HD Audio Controller
The HD Audio controller integrated into the ICH7-M complies with the Intel High Definition
Audio specification.
Page 17
KINO-9452 Mini-ITX SBC
Figure 2-7: HD Audio Codec
The HD audio controller is connected to the external peripheral interface controllers
through the integrated ALC883 HD Audio Codec. High Definition Audio supports up to
eight audio channels at 192KHz/32-bit quality and dual channel audio, allowing two
different audio streams simultaneously. Features include:
7.1 channel high definition audio
8 channels at 192KHz/32-bit quality
Dual channel audio
Automatic jack retasking
2.6.3 Intel® ICH7-M PCIe Bus: PCIe GbE Ethernet Controller
Two lanes of the PCIe bus on the Intel® ICH7-M chipset are interfaced to two external
RJ-45 LAN connectors through two Broadcom® BCM5787 PCIe GbE controllers. The two
RJ-45 connectors are shown in Figure 2-8. For more detailed information about the
Broadcom® BCM5787 PCIe GbE controller, please refer to Section 2.7.2 below.
Page 18
KINO-9452 Mini-ITX SBC
Figure 2-8: PCIe GbE Connectors
2.6.4 Intel® ICH7-M IDE Interface
The integrated IDE interface on the ICH7-M supports two IDE hard disks and ATAPI
devices. PIO IDE transfers up to 16 MB/s and Ultra ATA transfers of 100 MB/s. The
integrated IDE interface is able to support the following IDE HDDs:
Ultra ATA/100, with data transfer rates up to 100 MB/s
Ultra ATA/66, with data transfer rates up to 66 MB/s
Ultra ATA/33, with data transfer rates up to 33 MB/s
Specification
Ultra
Ultra
Ultra
ATA/100
ATA/66
ATA/100
IDE devices
2
2
2
PIO Mode
0–4
0–4
0–4
PIO Max Transfer Rate
16.6 MB/s
16.6 MB/s
16.6 MB/s
DMA/UDMA designation
UDMA 3 - 4
UDMA 3 – 4
UDMA 2
DMA/UDMA Max
100 MB/s
66 MB/s
33 MB/s
5V
5V
5V
Transfer
Controller Interface
Table 2-3: Supported HDD Specifications
Page 19
KINO-9452 Mini-ITX SBC
2.6.5 Intel® ICH7-M Low Pin Count (LPC) Interface
The ICH7-M LPC interface complies with the LPC 1.1 specifications. The LPC bus from
the ICH7 is connected to the following components:
BIOS chipset
Super I/O chipset
2.6.6 Intel® ICH7-M PCI Interface
The PCI interface on the ICH7-M is compliant with the PCI Revision 2.3 implementation.
Some of the features of the PCI interface are listed below.
PCI Revision 2.3 compliant
33 MHz
5V tolerant PCI signals (except PME#)
Integrated PCI arbiter supports up to seven PCI bus masters
The PCI bus is interfaced to one PCI slot and one Mini PCI slot of the KINO-9452 and
supports one PCI card and one Mini PCI card.
Figure 2-9: Mini PCI Slot
Page 20
KINO-9452 Mini-ITX SBC
2.6.7 Intel® ICH7-M Real Time Clock
256 bytes of battery backed RAM is provided by the Motorola MC146818A real time clock
(RTC) integrated into the ICH7-M. The RTC operates on a 3V battery and 32.768 KHz
crystal. The RTC keeps track of the time and stores system data even when the system is
turned off.
2.6.8 Intel® ICH7-M SATA Controller
The integrated SATA controller on the ICH7-M supports two SATA drives on the
KINO-9452 with independent DMA operations. SATA controller specifications are listed
below.
Supports two SATA drives
Supports 1.5 Gb/s data transfer speeds
Supports Serial ATA Specification, Revision 1.0a
2.6.9 Intel® ICH7-M USB Controller
Up to eight high-speed, full-speed or low-speed USB devices are supported by the
ICH7-M on the KINO-9452. High-speed USB 2.0, with data transfers of up to 480 MB/s, is
enabled with the ICH7-M integrated Enhanced Host Controller Interface (EHCI) compliant
host controller. USB full-speed and low-speed signaling is supported by the ICH7-M
integrated Universal Host Controller Interface (UHCI) controllers.
The eight USB ports implemented on the KINO-9452 are connected to four internal
connectors and four external connectors. See Figure 2-10.
Page 21
KINO-9452 Mini-ITX SBC
Figure 2-10: Onboard USB Implementation
2.7 PCIe Bus Components
2.7.1 PCIe Bus Overview
The PCIe bus is connected to components listed below:
Two PCIe GbE Broadcom LAN chipsets
2.7.2 Broadcom PCI Express GbE interface
The BCM5787M Broadcom PCI Express (PCIe) GbE controller is a 10/100/1000BASE-T
Ethernet LAN controller. The BCM5787M combines a triple-speed IEEE 802.3 compliant
Media Access Controller (MAC) with a triple-speed Ethernet transceiver, a PCIe bus
interface, and an on-chip buffer memory. Some of the BCM5787 controller features are
listed below:
Integrated 10/100/1000BASE-T transceiver
Automatic MDI crossover function
PCIe v1.0a
10/100/1000BASE-T full/half-duplex MAC
Wake on LAN support meeting the ACPI requirements
Statistics for SNMP MIB II, Ethernet-like MIB, and Ethernet MIB (802.3z,
Page 22
KINO-9452 Mini-ITX SBC
clause 30)
Serial EEPROM or serial flash support
JTAG support
2.8 LPC Bus Components
2.8.1 LPC Bus Overview
The LPC bus is connected to components listed below:
BIOS chipset
Super I/O chipset
2.8.2 BIOS Chipset
The BIOS chipset has a licensed copy of AMI BIOS installed on the chipset. Some of the
BIOS features are listed below:
AMI Flash BIOS
SMIBIOS (DMI) compliant
Console redirection function support
PXE (Pre-boot Execution Environment) support
USB booting support
2.8.3 Super I/O chipset
The iTE IT8712F Super I/O chipset is connected to the ICH7-M through the LPC bus. The
iTE IT8712F is an LPC interface-based Super I/O device that comes with Environment
Controller integration. Some of the features of the iTE IT8712F chipset are listed below:
LPC Interface
PC98/99/2001, ACPI and LANDesk Compliant
Enhanced Hardware Monitor
Fan Speed Controller
SmartGuardian Controller
Single +5V Power Supply
Two 16C550 UARTs for serial port control
Page 23
KINO-9452 Mini-ITX SBC
Keyboard Controller
Watchdog Timer
Serial IRQ Support
Vbat & Vcch Support
Single +5V Power Supply
Some of the Super I/O features are described in more detail below:
2.8.3.1 Super I/O LPC Interface
The LPC interface on the Super I/O complies with the Intel® Low Pin Count Specification
Rev. 1.0. The LPC interface supports both LDRQ# and SERIRQ protocols as well as PCI
PME# interfaces.
2.8.3.2 Super I/O 16C550 UARTs
The onboard Super I/O has two integrated 16C550 UARTs that can support the following:
Two standard serial ports (COM1 and COM2)
IrDa 1.0 and ASKIR protocols
Another two chipsets connected to the LPC bus provided connectivity to another two serial
port connectors (COM3 and COM4).
2.8.3.3 Super I/O Enhanced Hardware Monitor
The Super I/O Enhanced Hardware Monitor monitors three thermal inputs, VBAT
internally, and eight voltage monitor inputs. These hardware parameters are reported in
the BIOS and can be read from the BIOS Hardware Health Configuration menu.
2.8.3.4 Super I/O Fan Speed Controller
The Super I/O fan speed controller enables the system to monitor the speed of the fan.
One of the pins on the fan connector is reserved for fan speed detection and interfaced to
the fan speed controller on the Super I/O. The fan speed is then reported in the BIOS.
Page 24
KINO-9452 Mini-ITX SBC
2.8.3.5 Super I/O Keyboard Controller
The Super I/O keyboard controller can execute the 8042 instruction set. Some of the
keyboard controller features are listed below:
The 8042 instruction is compatible with a PS/2 keyboard and PS/2 mouse
Gate A20 and Keyboard reset output
Supports multiple keyboard power on events
Supports mouse double-click and/or mouse move power on events
2.8.4 Fintek F81216DG LPC Serial Port Chipset
The KINO-9452 has a Fintek F81216DG chipset onboard enables the addition of two
additional UART serial ports (COM3 and COM4). UART includes 16-byte send/receive
FIFO. The Fintek serial port chipset is interfaced to the ICH7-M chipset through the LPC
bus. Some of the features of the Fintek chipset are listed below:
Supports LPC interface
Totally provides 2 UART (16550 asynchronous) ports
o
o
1 x Pure UART
1 x UART+IR
One Watch dog timer with WDTOUT# signal
One Frequency input 24/48 MHz
Powered by 3Vcc
2.9 Environmental and Power Specifications
2.9.1 System Monitoring
Three thermal inputs on the KINO-9452 Super I/O Enhanced Hardware Monitor monitor
the following temperatures:
CPU temperature
System temperature
Eight voltage inputs on the KINO-9452 Super I/O Enhanced Hardware Monitor monitor the
following voltages:
Page 25
KINO-9452 Mini-ITX SBC
CPU Core
+2.5V
+3.30V
+5.00V
+12.0V
GMCH (1.5V)
+1.05V
5VSB
VBAT
The KINO-9452 Super I/O Enhanced Hardware Monitor also monitors the following fan
speeds:
CPU Fan speed
System Fan speed
Northbridge Fan speed
The values for the above environmental parameters are all recorded in the BIOS
Hardware Health Configuration menu.
2.9.2 Operating Temperature and Temperature Control
The maximum and minimum operating temperatures for the KINO-9452 are listed below.
Minimum Operating Temperature: 0ºC (32°F)
Maximum Operating Temperature: 60°C (140°F)
A cooling fan and heat sink must be installed on the CPU. Thermal paste must be
smeared on the lower side of the heat sink before it is mounted on the CPU. Heat sinks
are also mounted on the GMCH and ICH chipsets to ensure the operating temperature of
these chips remain low.
2.9.3 Power Consumption
Table 2-4 shows the power consumption parameters for the KINO-9452 running with a
1.60 GHz Intel® CoreTM2 Duo processor with two 1 GB DDR2 memory modules.
Page 26
KINO-9452 Mini-ITX SBC
Voltage
Current
+3.3V
3.12 A
+5V
1.58 A
+12V
2.05A
5V Standby
0.32A
Table 2-4: Power Consumption
Page 27
KINO-9452 Mini-ITX SBC
Chapter
3
3 Unpacking
Page 28
KINO-9452 Mini-ITX SBC
3.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the installation of the
KINO-9452 may result in permanent damage to the KINO-9452 and
severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the KINO-9452. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the KINO-9452, or any other electrical component is handled, the
following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
Self-grounding: Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
Use an anti-static pad: When configuring the KINO-9452, place it on an
antic-static pad. This reduces the possibility of ESD damaging the
KINO-9452.
Only handle the edges of the PCB: When handling the PCB, hold the PCB
by the edges.
3.2 Unpacking
3.2.1 Unpacking Precautions
When the KINO-9452 is unpacked, please do the following:
Follow the anti-static precautions outlined in Section 3.1.
Make sure the packing box is facing upwards so the KINO-9452 does not fall
out of the box.
Make sure all the components shown in Section 3.3 are present.
Page 29
KINO-9452 Mini-ITX SBC
3.3 Unpacking Checklist
NOTE:
If some of the components listed in the checklist below are missing,
please do not proceed with the installation. Contact the IEI reseller or
vendor you purchased the KINO-9452 from or contact an IEI sales
representative directly. To contact an IEI sales representative, please
send an email to [email protected]
3.3.1 Package Contents
The KINO-9452 is shipped with the following components:
Quantity
Item and Part Number
1
KINO-9452 SBC
1
Dual RS-232 Cable
(P/N: 32200-028401-RS)
1
HDTV cable
(P/N: 32000-083100-RS)
1
IDE cable
(P/N: 32200-000052-RS)
Page 30
Image
KINO-9452 Mini-ITX SBC
2
SATA cables
(P/N: 32000-062800-RS)
1
SATA power cable
(P/N: 32100-088600-RS)
1
I/O Shielding
(P/N: 45002-4520C0-00-RS)
1
Mini jumper Pack
1
Quick Installation Guide
1
Utility CD
Table 3-1: Package List Contents
3.3.2 Optional Items
NOTE:
The items listed in this section are optional items that must be ordered
separately. Please contact your KINO-9452 vendor, distributor or
reseller for more information or, contact iEi directly by sending an email
to [email protected]
The following optional items are available for the KINO-9452.
Page 31
KINO-9452 Mini-ITX SBC
Quantity
1
Item and Part Number
Dual port USB cable
(P/N: CB-USB02-RS)
1
RS-232/422/485 cable
(P/N: 32200-000077-RS)
1
CPU Cooler
(P/N: CF-479B-RS)
Table 3-2: Optional Items
Page 32
Image
KINO-9452 Mini-ITX SBC
Chapter
4
4 Connectors and
Jumpers
Page 33
KINO-9452 Mini-ITX SBC
4.1 Peripheral Interface Connectors
Section 4.1.1 shows peripheral interface connector locations. Section 4.1.2 lists all the
peripheral interface connectors seen in Section 4.1.1.
4.1.1 KINO-9452 Layout
Figure 4-1 shows the on-board peripheral connectors, backplane peripheral connectors
and on-board jumpers.
Figure 4-1: Connector and Jumper Locations
Page 34
KINO-9452 Mini-ITX SBC
4.1.2 Peripheral Interface Connectors
Table 4-1 shows a list of the peripheral interface connectors on the KINO-9452. Detailed
descriptions of these connectors can be found in Section 4.2.
Connector
Type
Label
DDR2 DIMM socket
240-pin slot
DIMM1
DDR2 DIMM socket
240-pin slot
DIMM2
Fan connector (CPU)
3-pin wafer
CPU_FAN1
Fan connector (System)
3-pin wafer
SYS_FAN1
Fan connector (Northbridge)
3-pin wafer
NB_FAN1
Front panel connector
14-pin header
F_PANEL1
Front panel audio connector
10-pin header
AUDIO2
Digital Input/Output connector
10-pin header
DIO1
IDE Interface connector
40-pin box header
IDE1
LCD backlight connector
6-pin wafer
CN1
LVDS LCD connector
30-pin crimp
LVDS1
Mini PCI slot
124-pin Mini PCI Type III slot
MINIPCI
PCI slot
124-pin PCI slot
PCI2
Power connector
20-pin connector
PWR1
Serial port connector (1)
10-pin header
COM2
Serial port connector (2)
14-pin header
COM3
Serial port connector (3)
10-pin header
COM4
SATA drive connector (1)
7-pin SATA connector
SATA1
SATA drive connector (2)
7-pin SATA connector
SATA2
Page 35
KINO-9452 Mini-ITX SBC
SPDIF connector
5-pin header
SPDIF1
USB connector (1)
8-pin header
USB4
USB connector (2)
8-pin header
USB5
Table 4-1: Peripheral Interface Connectors
4.1.3 Rear Panel Connectors
Table 4-2 lists the rear panel connectors on the KINO-9452. Detailed descriptions of these
connectors can be found in Section 4.3.
Connector
Type
Label
Audio Jacks
Audio connector
AUDIO1
CRT connector
15-pin female connector
CRT_COM1
Ethernet connector (1)
RJ-45 connector
LAN/USB1A
Ethernet connector (2)
RJ-45 connector
LAN/USB2A
Keyboard/Mouse connector
6-pin mini din connector
KBMS1
Serial port connector
DB-9 male connector
CRT_COM1
TV-Out port
7-pin TV port
TV
USB 2.0 port (1)
USB port connector
LAN/USB1B
USB 2.0 port (2)
USB port connector
LAN/USB2B
Table 4-2: Rear Panel Connectors
Page 36
KINO-9452 Mini-ITX SBC
4.2 Internal Peripheral Connectors
Internal peripheral connectors are found on the motherboard and are only accessible
when the motherboard is outside of the chassis. This section has complete descriptions of
all the internal, peripheral connectors on the KINO-9452.
4.2.1 Audio Connector
CN Label:
AUDIO2
CN Type:
10-pin header (2x5)
CN Location:
See Figure 4-2
CN Pinouts:
See Table 4-3
The front panel audio connector connects the on-board sound system of the KINO-9452 to
the audio line out and microphone jacks on the front of the computer chassis.
Figure 4-2: Audio Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1.
MIN2_L
2.
GND
3.
MIN2_R
4.
PRESENCE
5.
LINE2_L
6.
SENSE1_RETUR
7.
SENSE_SEND
8.
(KEY)
9.
LINE2_R
10.
SENSE2_RETUR
Table 4-3: Audio Connector Pinouts
Page 37
KINO-9452 Mini-ITX SBC
4.2.2 Fan Connectors
CN Label:
CPU_FAN1, SYS_FAN1 and NB_FAN1
CN Type:
3-pin wafer connector (1x3)
CN Location:
See Figure 4-3
CN Pinouts:
See Table 4-4
The cooling fan connectors on the KINO-9452 provide a 12 V, 500 mA current to one CPU
cooling fan, one system cooling fan and one Northbridge cooling fan. There is a “sense”
pin in the fan connector, which transfers the fan’s sense signal to the system BIOS in
order to recognize the fan speed. Please note that only some specific types of fans offer a
rotation signal.
Figure 4-3: Fan Connector Locations
PIN NO.
DESCRIPTION
1
GND
2
+12V
3
Sense
Table 4-4: Fan Connector Pinouts
Page 38
KINO-9452 Mini-ITX SBC
4.2.3 Front Panel Connector
CN Label:
F_PANEL1
CN Type:
14-pin header (2x7)
CN Location:
See Figure 4-4
CN Pinouts:
See Table 4-5
The front panel connector connects to several external switches and indicators to monitor
and control the motherboard. These indicators and switches include:
Power
Power button
Reset button
Speaker
HDD
Figure 4-4: Front Panel Connector Location
Page 39
KINO-9452 Mini-ITX SBC
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
Power LED+
2
Speaker+
3
NC
4
NC
5
Power LED-
6
NC
7
Power Button#
8
Speaker-
9
Power Button
10
NC
11
IDE LED+
12
Reset Button
13
IDE LED-
14
Reset Button#
Table 4-5: Front Panel Connector Pinouts
4.2.4 Digital Input/Output Connector
CN Label:
DIO1
CN Type:
10-pin header (2x5)
CN Location:
See Figure 4-5
CN Pinouts:
See Table 4-6
The DIO connector is managed through a Super I/O chip. The DIO connector pins are
user programmable. The digital IO port of KINO-9452 is 5 V CMOS level.
Figure 4-5: GPIO Connector Location
Page 40
KINO-9452 Mini-ITX SBC
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
GND
2
+5V
3
INPUT0
4
OUTPUT0
5
INPUT1
6
OUTPUT1
7
INPUT2
8
OUTPUT2
9
INPUT3
10
OUTPUT3
Table 4-6: GPIO Connector Pinouts
4.2.5 IDE Connector
CN Label:
IDE1
CN Type:
40-pin box header (2x20)
CN Location:
See Figure 4-6
CN Pinouts:
See Table 4-7
One primary 40-pin IDE device connector on the KINO-9452 motherboard supports
connectivity to ATA 100/66/33 IDE devices with data transfer rates up to 100 MB/s.
Figure 4-6: IDE Device Connector Location
Page 41
KINO-9452 Mini-ITX SBC
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
RESET#
2
GND
3
DATA 7
4
DATA 8
5
DATA 6
6
DATA 9
7
DATA 5
8
DATA 10
9
DATA 4
10
DATA 11
11
DATA 3
12
DATA 12
13
DATA 2
14
DATA 13
15
DATA 1
16
DATA 14
17
DATA 0
18
DATA 15
19
GND
20
(KEY)
21
DRQ
22
GND
23
IOW#
24
GND
25
IOR#
26
GND
27
CHRDY
28
GND
29
DACK
30
GND
31
INTERRUPT
32
N/C
33
SA1
34
P66DET
35
SA0
36
SA2
37
HDC CS0#
38
HDC CS1#
39
HDD ACTIVE#
40
GND
Table 4-7: IDE Connector Pinouts
4.2.6 LCD Backlight Connector
CN Label:
CN1
CN Type:
6-pin wafer connector (1x6)
CN Location:
See Figure 4-7
CN Pinouts:
See Table 4-8
The LCD backlight connector is for the LCD inverter connection.
Page 42
KINO-9452 Mini-ITX SBC
Figure 4-7: LCD Backlight Connector Location
PIN NO.
DESCRIPTION
1
Back Light Power
2
Back Light Power
3
Back Light enable
4
NC
5
GND
6
GND
Table 4-8: LCD Backlight Connector Pinouts
4.2.7 LVDS LCD connector
CN Label:
LVDS1
CN Type:
30-pin crimp connector (2x15)
CN Location:
See Figure 4-8
CN Pinouts:
See Table 4-9
The connector supports one or two channel 18-bit or 24-bit LVDS panel.
Page 43
KINO-9452 Mini-ITX SBC
Figure 4-8: LVDS LCD Connector Location
PIN NO.
1
DESCRIPTION
GND
st
PIN NO.
DESCRIPTION
2
GND
3
1 LVDS data0 output +
4
1st LVDS data0 output -
5
1st LVDS data1 output +
6
1st LVDS data1 output -
7
1st LVDS data2 output +
8
1st LVDS data2 output -
9
1st LVDS clock output +
10
1st LVDS clock output -
11
NC
12
NC
13
GND
14
GND
15
2nd LVDS data0 output +
16
2nd LVDS data0 output -
17
2nd LVDS data1 output +
18
2nd LVDS data1 output -
19
2nd LVDS data2 output +
20
2nd LVDS data2 output -
21
2nd LVDS clock output +
22
2nd LVDS clock output -
23
NC
24
NC
25
GND
26
GND
27
+LCD (3.3V, 5V or 12V)
28
+LCD (3.3V, 5V or 12V)
29
+LCD (3.3V, 5V or 12V)
30
+LCD (3.3V, 5V or 12V)
Table 4-9: LVDS LCD Connector Pinouts
Page 44
KINO-9452 Mini-ITX SBC
4.2.8 Mini PCI Slot
CN Label:
MINIPCI
CN Type:
124-pin Mini PCI Type III slot
CN Location:
See Figure 4-9
CN Pinouts:
See Table 4-10
Mini PCI is a small form factor version of a PCI card. Mini PCI expansion devices can be
inserted into the Mini PCI slot.
Figure 4-9: Mini PCI Slot Location
PIN
NAME
PIN
NAME
PIN
NAME
PIN
NAME
1
TIP
32
GROUND
63
3.3V
94
AD[02]
2
RING
33
AD[31]
64
FRAME#
95
AD[03]
3
8PMJ-3
34
PME#
65
CLKRUN#
96
AD[00]
4
8PMJ-1
35
AD[29]
66
TRDY#
97
5V
5
8PMJ-6
36
RESERVED
67
SERR#
98
RESERVED_WIP5
6
8PMJ-2
37
GROUND
68
STOP#
99
AD[01]
7
8PMJ-7
38
AD[30]
69
GROUND
100
RESERVED_WIP5
8
8PMJ-4
39
AD[27]
70
3.3V
101
GROUND
9
8PMJ-8
40
3.3V
71
PERR#
102
GROUND
Page 45
KINO-9452 Mini-ITX SBC
10
8PMJ-5
41
AD[25]
72
DEVSEL#
103
AC_SYNC
11
LED1_GRNP
42
AD[28]
73
C/BE[1]#
104
M66EN
12
LED2_YELP
43
RESERVED
74
GROUND
105
AC_SDATA_IN
13
LED1_GRNN
44
AD[26]
75
AD[14]
106
AC_SDATA_OUT
14
LED2_YELN
45
C/BE[3]#
76
AD[15]
107
AC_BIT_CLK
15
CHSGND
46
AD[24]
77
GROUND
108
AC_CODEC_ID0#
16
RESERVED
47
AD[23]
78
AD[13]
109
AC_CODEC_ID1#
17
INTB#
48
IDSEL
79
AD[12]
110
AC_RESET#
18
5V
49
GROUND
80
AD[11]
111
MOD_AUDIO_MON
19
3.3V
50
GROUND
81
AD[10]
112
RESERVED
20
INTA#
51
AD[21]
82
GROUND
113
AUDIO_GND
21
RESERVED
52
AD[22]
83
GROUND
114
GROUND
22
RESERVED
53
AD[19]
84
AD[09]
115
SYS_AUDIO_OUT
23
GROUND
54
AD[20]
85
AD[08]
116
SYS_AUDIO_IN
24
3.3VAUX
55
GROUND
86
C/BE[0]#
117
SYS_AUDIO_OUT GND
25
CLK
56
PAR
87
AD[07]
118
SYS_AUDIO_IN GND
26
RST#
57
AD[17]
88
3.3V
119
AUDIO_GND
27
GROUND
58
AD[18]
89
3.3V
120
AUDIO_GND
28
3.3V
59
C/BE[2]#
90
AD[06]
121
RESERVED
29
REQ#
60
AD[16]
91
AD[05]
122
MPCIACT#
30
GNT#
61
IRDY#
92
AD[04]
123
VCC5VA
31
3.3V
62
Ground
93
RESERVED
124
3.3VAUX
Table 4-10: Mini PCI Slot Pinouts
4.2.9 Power Connector
CN Label:
PWR1
CN Type:
20-pin connector
CN Location:
See Figure 4-10
CN Pinouts:
See Table 4-11
This 20-pin power connector supports the ATX power supply.
Page 46
KINO-9452 Mini-ITX SBC
Figure 4-10: Power Connector Location
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
3.3V
11
3.3V
2
3.3V
12
-12V
3
GND
13
GND
4
+5V
14
PS_ON
5
GND
15
GND
6
+5V
16
GND
7
GND
17
GND
8
Power good
18
-5V
9
5VSB
19
+5V
10
+12V
20
+5V
Table 4-11: Power Connector Pinouts
4.2.10 14-Pin Serial Port Connectors
CN Label:
COM3
CN Type:
14-pin header (2x7)
Page 47
KINO-9452 Mini-ITX SBC
CN Location:
See Figure 4-11
CN Pinouts:
See Table 4-12
The serial ports connectors connect to RS-232/422/485 serial port device.
Figure 4-11: 14-Pin Serial Port Connector Locations
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTS
7
DTR
8
RI
9
GND
10
NC
11
TX+
12
TX-
13
RX+
14
RX-
Table 4-12: COM3 Pinouts
4.2.11 10-Pin Serial Port Connectors
CN Label:
COM2 and COM4
CN Type:
10-pin header (2x5)
CN Location:
See Figure 4-12
CN Pinouts:
See Table 4-13
Page 48
KINO-9452 Mini-ITX SBC
The serial ports connectors connect to RS-232 serial port device.
Figure 4-12: 10-Pin Serial Port Connector Locations
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTS
7
DTR
8
RI
9
GND
10
NC
Table 4-13: COM2 and COM4 Pinouts
4.2.12 SATA Drive Connectors
CN Label:
SATA1 and SATA2
CN Type:
7-pin SATA drive connectors (1x7)
CN Location:
See Figure 4-13
CN Pinouts:
See Table 4-14
The two SATA drive connectors are connected to two SATA drives. SATA drives transfer
data at speeds as high as 1.5 Gb/s.
Page 49
KINO-9452 Mini-ITX SBC
Figure 4-13: SATA Drive Connector Locations
PIN NO.
DESCRIPTION
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
Table 4-14: SATA Drive Connector Pinouts
4.2.13 SPDIF Connector
CN Label:
SPDIF1
CN Type:
5-pin header (1x5)
CN Location:
See Figure 4-14
CN Pinouts:
See Table 4-15
Page 50
KINO-9452 Mini-ITX SBC
The SPDIF connector connects to the S/PDIF audio module, which bears S/PDIF digital
output. S/PDIF (Sony/Philips Digital Interface) is a newest audio transfer file format, which
allows the user to enjoy digital audio. The SPDIF1 port provides digital audio to external
speaker or compressed AC3 data to an external Dolby Digital Decoder via a coaxial cable.
Figure 4-14: SPDIF Connector Locations
PIN NO.
DESCRIPTION
1
+5V
2
(KEY)
3
SPDIF_OUT
4
GND
5
SPDIF_IN
Table 4-15: SPDIF Pinouts
4.2.14 Internal USB Connectors
CN Label:
USB4 and USB5
CN Type:
8-pin header (2x4)
CN Location:
See Figure 4-15
CN Pinouts:
See Table 4-16
Page 51
KINO-9452 Mini-ITX SBC
One 2x4 pin connector provides connectivity to two USB 2.0 ports. The USB ports are
used for I/O bus expansion.
Figure 4-15: Internal USB Connector Locations
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
VCC
2
GND
3
DATA0-
4
DATA1+
5
DATA0+
6
DATA1-
7
GND
8
VCC
Table 4-16: USB3 and USB4 Pinouts
4.3 External Interface Connectors
The peripheral connectors on the back panel are connected to devices externally when
the KINO-9452 is installed in a chassis. The peripheral connectors on the rear panel are:
6 x Audio jacks
1 x CRT connector
2 x RJ-45 Ethernet connectors
1 x Keyboard connector
1 x Mouse connector
1 x Serial port connector
1 x TV-Out connector
Page 52
KINO-9452 Mini-ITX SBC
4 x USB 2.0 connectors
Figure 4-16: KINO-9452 External Interface Connectors
4.3.1 Audio Connectors
CN Label:
AUDIO1
CN Type:
Audio jack
CN Location:
See Figure 4-16 (labeled number 7)
CN Pinouts:
See Figure 4-17
Center/Subwoofer port (Yellow): Connects the center/subwoofer speakers.
Line In port (Light Blue): Connects a CD-ROM, DVD player, or other audio
devices.
Rear Speaker Out port (Black): Connects the rear speakers in a
4/6/8-channel audio configuration.
Line Out port (Lime): Connects a headphone or a speaker. In 4,6,8-channel
configuration, the function of this port becomes Front Speaker Out.
Side Speaker Out port (Gray): Connectors the side speakers in an
8-channel audio configuration.
Microphone (Pink): Connects a microphone.
Page 53
KINO-9452 Mini-ITX SBC
Figure 4-17: Audio Connectors
4.3.2 CRT Connector
CN Label:
CRT_COM1
CN Type:
15-pin female connector
CN Location:
See Figure 4-16 (labeled number 9)
CN Pinouts:
See Table 4-17
The standard 15-pin VGA connector connects to a CRT or LCD display monitor.
Figure 4-18: VGA Connector
PIN NO.
Page 54
DESCRIPTION
PIN NO.
DESCRIPTION
1
RED
2
GREEN
3
BLUE
4
N/C
5
GND
6
GND
7
GND
8
GND
9
VCC
10
GND
11
N/C
12
DDC DAT
KINO-9452 Mini-ITX SBC
13
HSYNC
15
DDC CLK
14
VSYNC
Table 4-17: VGA Connector Pinouts
4.3.3 Ethernet Connectors
CN Label:
LAN/USB1A and LAN/USB2A
CN Type:
RJ-45
CN Location:
See Figure 4-16 (labeled number 4 and 6)
CN Pinouts:
See Table 4-18
The KINO-9452 is equipped with two built-in GbE Ethernet controllers. The controllers can
connect to the LAN through two RJ-45 LAN connectors. There are two LEDs on the
connector indicating the status of LAN. The pin assignments are listed in the following
table:
PIN
DESCRIPTION
PIN
DESCRIPTION
1
MDX0+
5
MDX2-
2
MDX0-
6
MDX1-
3
MDX1+
7
MDX3+
4
MDX2+
8
MDX3-
Table 4-18: LAN1 and LAN2 Pinouts
Figure 4-19: RJ-45 Ethernet Connector
Page 55
KINO-9452 Mini-ITX SBC
The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green
LED indicates activity on the port and the yellow LED indicates the port is linked. See
Table 4-19.
SPEED LED
STATUS
DESCRIPTION
ACT/LINK LED
STATUS
DESCRIPTION
OFF
10Mbps connection
OFF
No link
ORANGE
100Mbps connection
YELLOW
Linked
GREEN
1Gbps connection
BLINKING
Data Activity
Table 4-19: RJ-45 Ethernet Connector LEDs
4.3.4 Keyboard/Mouse Connector
CN Label:
KBMS1
CN Type:
PS/2 connector
CN Location:
See Figure 4-16 (labeled number 1)
CN Pinouts:
See Table 4-20
The KINO-9452 keyboard and mouse connectors are standard PS/2 connectors.
Figure 4-20: PS/2 Pinouts
Page 56
KINO-9452 Mini-ITX SBC
PIN
DESCRIPTION
PIN
DESCRIPTION
1
L_KDAT
7
L_MDAT
2
NC
8
NC
3
GND
9
GND
4
5V
10
5V
5
L_KCLK
11
L_MCLK
6
NC
12
NC
Table 4-20: PS/2 Connector Pinouts
4.3.5 Serial Port Connectors
CN Label:
CRT_COM1
CN Type:
DB-9
CN Location:
See Figure 4-16 (labeled number 2)
CN Pinouts:
See Table 4-21
The serial ports can be connected to a serial communications device directly.
Figure 4-21: External Serial Port Connector
PIN
Description
1
DATA CARRIER DETECT (DCD)
2
RECEIVE DATA (RXD)
3
TRANSMIT DATA (TXD)
4
DATA TERMINAL READY (DTR)
Page 57
KINO-9452 Mini-ITX SBC
5
GROUND (GND)
6
DATA SET READY (DSR)
7
REQUEST TO SEND (RTS)
8
CLEAR TO SEND (CTS)
9
RING INDICATOR (RI)
Table 4-21: External Serial Port Pinouts
4.3.6 TV-Out Connector
CN Label:
TV
CN Type:
7-pin TV port
CN Location:
See Figure 4-16 (labeled number 8)
CN Pinouts:
See Table 4-22
The TV-out port connects to a TV.
Figure 4-22: TV-Out Connector
PIN
Description
1
Ground
2
Ground
3
S-Vidio Luminance
Component:Luminance (Y)
4
S-Vidio:Chrominance
Component:Chrominance (Pr)
Page 58
KINO-9452 Mini-ITX SBC
5
NC
6
Ground
7
Composite:CVBS
Component:Chrominance (Pb)
Table 4-22: TV-Out Pinouts
4.3.7 USB Connector
CN Label:
LAN/USB1B and LAN/USB2B
CN Type:
USB port
CN Location:
See Figure 4-16 (labeled number 3 and 5)
CN Pinouts:
See Table 4-23
USB devices can be connected directly to the USB connectors on the rear panel.
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
VCC
5
VCC
2
USBD0-
6
USBD1-
3
USBD0+
7
USBD1+
4
GND
8
GND
Table 4-23: External USB Connector Pinouts
Page 59
KINO-9452 Mini-ITX SBC
Chapter
5
5 Installation
Page 60
KINO-9452 Mini-ITX SBC
5.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the installation of the
KINO-9452 may result in permanent damage to the KINO-9452 and
severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the KINO-9452. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the KINO-9452, or any other electrical component is handled, the
following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
Self-grounding: Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
Use an anti-static pad: When configuring the KINO-9452, place it on an
antic-static pad. This reduces the possibility of ESD damaging the
KINO-9452.
Only handle the edges of the PCB: When handling the PCB, hold the PCB
by the edges.
Page 61
KINO-9452 Mini-ITX SBC
5.2 Installation Considerations
NOTE:
The following installation notices and installation considerations should
be read and understood before the KINO-9452 is installed. All
installation notices pertaining to the installation of the KINO-9452
should be strictly adhered to. Failing to adhere to these precautions
may lead to severe damage of the KINO-9452 and injury to the person
installing the motherboard.
5.2.1 Installation Notices
WARNING:
The installation instructions described in this manual should be
carefully followed in order to prevent damage to the KINO-9452,
KINO-9452 components and injury to the user.
Before and during the installation please DO the following:
Read the user manual:
o
The user manual provides a complete description of the KINO-9452
installation instructions and configuration options.
Wear an electrostatic discharge cuff (ESD):
o
Electronic components are easily damaged by ESD. Wearing an ESD cuff
removes ESD from the body and helps prevent ESD damage.
Place the KINO-9452 on an antistatic pad:
o
When installing or configuring the motherboard, place it on an antistatic
pad. This helps to prevent potential ESD damage.
Turn all power to the KINO-9452 off:
Page 62
KINO-9452 Mini-ITX SBC
o
When working with the KINO-9452, make sure that it is disconnected from
all power supplies and that no electricity is being fed into the system.
Before and during the installation of the KINO-9452 DO NOT:
Remove any of the stickers on the PCB board. These stickers are required for
warranty validation.
Use the product before verifying all the cables and power connectors are
properly connected.
Allow screws to come in contact with the PCB circuit, connector pins, or its
components.
5.2.2 Installation Checklist
The following checklist is provided to ensure the KINO-9452 is properly installed.
All the items in the packing list are present
The CPU is installed
The CPU cooling kit is properly installed
A compatible memory module is properly inserted into the slot
The CF Type I or CF Type II card is properly installed into the CF socket
The jumpers have been properly configured
The KINO-9452 is inserted into a chassis with adequate ventilation
The correct power supply is being used
The following devices are properly connected
o
o
o
o
o
IDE device
SATA drives
Power supply
USB cable
Serial port cable
The following external peripheral devices are properly connected to the
chassis:
o
o
o
o
Audio device
VGA screen
Keyboard
Mouse
Page 63
KINO-9452 Mini-ITX SBC
o
RS-232 serial communications device
5.3 CPU, CPU Cooling Kit and DIMM Installation
WARNING:
A CPU should never be turned on without the specified cooling kit
being installed. If the cooling kit (heat sink and fan) is not properly
installed and the system turned on, permanent damage to the CPU,
KINO-9452 and other electronic components attached to the system
may be incurred. Running a CPU without a cooling kit may also result
in injury to the user.
The CPU, CPU cooling kit and DIMM are the most critical components of the KINO-9452.
If one of these component is not installed the KINO-9452 cannot run.
5.3.1 Socket 479 CPU Installation
WARNING:
CPUs are expensive and sensitive components. When installing the
CPU please be careful not to damage it in anyway. Make sure the CPU
is installed properly and ensure the correct cooling kit is properly
installed.
To install a socket 479 CPU onto the KINO-9452, follow the steps below:
WARNING:
When handling the CPU, only hold it on the sides. DO NOT touch the
pins at the bottom of the CPU.
Page 64
KINO-9452 Mini-ITX SBC
Step 1: Unlock the CPU retention screw. When shipped, the retention screw of the
CPU socket should be in the unlocked position. If it is not in the unlocked
position, use a screwdriver to unlock the screw. See Figure 5-1.
Figure 5-1: Make sure the CPU socket retention screw is unlocked
Step 2: Inspect the CPU socket. Make sure there are no bent pins and make sure the
socket contacts are free of foreign material. If any debris is found, remove it with
compressed air.
Step 3: Correctly Orientate the CPU. Make sure the IHS (integrated heat sink) side is
facing upwards.
Step 4: Correctly position the CPU. Match the Pin 1 mark with the cut edge on the
CPU socket. See Figure 5-1.
Step 5: Align the CPU pins. Carefully align the CPU pins with the holes in the CPU
socket.
Step 6: Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are
properly aligned, the CPU should slide into the CPU socket smoothly.
Step 7: Lock the retention screw. Rotate the retention screw into the locked position.
Page 65
KINO-9452 Mini-ITX SBC
See Figure 5-2.Step 0:
Figure 5-2: Lock the CPU Socket Retention Screw
5.3.2 Cooling Kit CF-479B-RS Installation
Figure 5-3: IEI CF-479B-RS Cooling Kit
An IEI Socket 479 CPU cooling kit can be purchased separately. The cooling kit
comprises a CPU heat sink and a cooling fan.
Page 66
KINO-9452 Mini-ITX SBC
WARNING:
Do not wipe off (accidentally or otherwise) the pre-sprayed layer of
thermal paste on the bottom of the CF-479B-RS heat sink. The thermal
paste between the CPU and the heat sink is important for optimum
heat dissipation.
To install the CF-479B-RS cooling kit, please follow the steps below.
Step 1: Place the cooling kit onto the CPU. Make sure the CPU cooling fan cable
can be properly routed when the cooling kit is installed.
Step 2: Properly align the cooling kit. Make sure its four spring screw fasteners can
pass through the pre-drilled holes on the PCB.
Step 3: Secure the cooling kit. From the solder side of the PCB, align the support
bracket to the screw threads on heat sink that were inserted through the PCB
holes. (See Figure 5-4)
Figure 5-4: Cooling Kit Support Bracket
Step 4: Tighten the screws. Use a screwdriver to tighten the four screws. Tighten each
nut a few turns at a time and do not over-tighten the screws.
Page 67
KINO-9452 Mini-ITX SBC
Step 5: Connect the fan cable. Connect the cooling kit fan cable to the fan connector
on the motherboard. Carefully route the cable and avoid heat generating chips
and fan blades. See Figure 5-5. Step 0:
Figure 5-5: Connect the cooling fan cable
5.3.3 DIMM Installation
WARNING:
Only DDR2 memory module can be installed on the KINO-9452. Do not
install DDR memory modules. If a DDR memory module is installed on
the KINO-9452, the KINO-9452 may be irreparably damaged. Please
make sure the purchased DIMM complies with the memory
specifications of the KINO-9452. DIMM specifications compliant with
the KINO-9452 are listed in Chapter 2.
To install a DIMM into a DIMM socket, please follow the steps below and refer to
Figure 5-6.
Page 68
KINO-9452 Mini-ITX SBC
Figure 5-6: Installing a DIMM
Step 1: Open the DIMM socket handles. The DIMM socket has two handles that
secure the DIMM into the socket. Before the DIMM can be inserted into the
socket, the handles must be opened. See Figure 5-6.
Step 2: Align the DIMM with the socket. The DIMM must be oriented in such a way
that the notch in the middle of the DIMM must be aligned with the plastic bridge
in the socket. See Figure 5-6.
Step 3: Insert the DIMM. Once properly aligned, the DIMM can be inserted into the
socket. As the DIMM is inserted, the white handles on the side of the socket will
close automatically and secure the DIMM to the socket. See Figure 5-6.
Step 4: Removing a DIMM. To remove a DIMM, push both handles outward. The
memory module is ejected by a mechanism in the socket.Step 0:
Page 69
KINO-9452 Mini-ITX SBC
5.4 Jumper Settings
NOTE:
A jumper is a metal bridge used to close an
electrical circuit. It consists of two or three metal
pins and a small metal clip (often protected by a
plastic cover) that slides over the pins to connect
them. To CLOSE/SHORT a jumper means
connecting the pins of the jumper with the plastic
clip and to OPEN a jumper means removing the
Figure 5-7: Jumper Locations
plastic clip from a jumper.
Before the KINO-9452 is installed in the system, the jumpers must be set in accordance
with the desired configuration. The jumpers on the KINO-9452 are listed in Table 5-1.
Description
Label
Type
AT/ATX power mode selection
JP5, JP6
2-pin header
Clear CMOS
JP3
3-pin header
COM3 mode selection
JP1, JP7
6-pin header
LVDS screen resolution selection
JP4
8-pin header
LVDS voltage selection
JP2
6-pin header
Table 5-1: Jumpers
5.4.1 AT/ATX Power Select Jumper Settings
Jumper Label:
JP5 and JP6
Jumper Type:
2-pin header
Jumper Settings:
See Table 5-2
Page 70
KINO-9452 Mini-ITX SBC
Jumper Location:
See Figure 5-8
The AT/ATX Power Select jumper specifies the systems power mode as AT or ATX.
AT/ATX Power Select jumper settings are shown in Table 5-2.
JP5
Description
Short
Use ATX power
Open
Use AT power
JP6
Description
Short
Use AT power
Open
Use ATX power
Default
Default
Table 5-2: AT/ATX Power Select Jumper Settings
The location of the AT/ATX Power Select jumper is shown in Figure 5-8 below.
Figure 5-8: AT/ATX Power Select Jumper Location
Page 71
KINO-9452 Mini-ITX SBC
5.4.2 Clear CMOS Jumper
Jumper Label:
JP3
Jumper Type:
3-pin header
Jumper Settings:
See Table 5-3
Jumper Location:
See Figure 5-9
If the KINO-9452 fails to boot due to improper BIOS settings, the clear CMOS jumper
clears the CMOS data and resets the system BIOS information. To do this, use the jumper
cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1
and 2.
If the “CMOS Settings Wrong” message is displayed during the boot up process, the fault
may be corrected by pressing the F1 to enter the CMOS Setup menu. Do one of the
following:
Enter the correct CMOS setting
Load Optimal Defaults
Load Failsafe Defaults.
After having done one of the above, save the changes and exit the CMOS Setup menu.
The clear CMOS jumper settings are shown in Table 5-3.
Clear CMOS
Description
Short 1 - 2
Keep CMOS Setup
Short 2 - 3
Clear CMOS Setup
Default
Table 5-3: Clear CMOS Jumper Settings
The location of the clear CMOS jumper is shown in Figure 5-9 below.
Page 72
KINO-9452 Mini-ITX SBC
Figure 5-9: Clear CMOS Jumper
5.4.3 COM 3 Function Select Jumper
Jumper Label:
JP1 and JP7
Jumper Type:
6-pin header
Jumper Settings:
See Table 5-4
Jumper Location:
See Figure 5-10
The COM 3 Function Select jumper sets the communication protocol used by the second
serial communications port (COM 3) as RS-232, RS-422 or RS-485. The COM 3 Function
Select settings are shown in Figure 5-10.
Page 73
KINO-9452 Mini-ITX SBC
JP1
Description
Short 1-2
RS-232
Short 3-4
RS-422
Short 5-6
RS-485
JP7
Description
Short 1-3, 2-4
RS-232
Short 3-5, 4-6
RS-485
Default
Default
Table 5-4: COM 3 Function Select Jumper Settings
The COM 3 Function Select jumper location is shown in Table 5-4.
Figure 5-10: COM 3 Function Select Jumper Location
5.4.4 LVDS Screen Resolution Selection
Jumper Label:
JP4
Jumper Type:
8-pin header
Jumper Settings:
See Table 5-6
Jumper Location:
See Figure 5-12
Page 74
KINO-9452 Mini-ITX SBC
The LVDS Screen Resolution Selection jumper allows the LVDS screen voltage to be
set. The LVDS Screen Resolution Selection jumper settings are shown in Table 5-6.
LVDS Resolution Select
Description
Short 1-2
1024 x 768 (18-bit)
Short 3-4
1024 x 768 (24-bit)
Short 5-6
1280 x 1024 (48-bit)
Short 1-2 and 3-4
1280 x 1024 (36-bit)
Short 1-2 and 5-6
1600 x 1200 (36-bit)
Short 3-4 and 5-6
1600 x 1200 (48-bit)
Default
Table 5-5: LVDS Screen Resolution Selection Jumper Settings
The LVDS Screen Resolution Selection jumper location is shown in Figure 5-12.
Figure 5-11: LVDS Screen Resolution Selection Jumper Pinout Locations
Page 75
KINO-9452 Mini-ITX SBC
5.4.5 LVDS Voltage Selection
WARNING:
Permanent damage to the screen and KINO-9452 may occur if the
wrong voltage is selected with this jumper. Please refer to the user
guide that cam with the monitor to select the correct voltage.
Jumper Label:
JP2
Jumper Type:
6-pin header
Jumper Settings:
See Table 5-6
Jumper Location:
See Figure 5-12
The LVDS Voltage Selection jumper allows the LVDS screen voltage to be set. The
LVDS Voltage Selection jumper settings are shown in Table 5-6.
LVDS Voltage Select
Description
Short 1-2
+3V
Short 3-4
+5V
Short 5-6
+12V
Default
Table 5-6: LVDS Voltage Selection Jumper Settings
The LVDS Voltage Selection jumper location is shown in Figure 5-12.
Page 76
KINO-9452 Mini-ITX SBC
Figure 5-12: LVDS Voltage Selection Jumper Pinout Locations
5.5 Chassis Installation
5.5.1 Airflow
WARNING:
Airflow is critical to the cooling of the CPU and other onboard
components. The chassis in which the KINO-9452 must have air vents
to allow cool air to move into the system and hot air to move out.
The KINO-9452 must be installed in a chassis with ventilation holes on the sides allowing
airflow to travel through the heat sink surface. In a system with an individual power supply
unit, the cooling fan of a power supply can also help generate airflow through the board
surface.
Page 77
KINO-9452 Mini-ITX SBC
NOTE:
IEI has a wide range of backplanes available. Please contact your
KINO-9452 vendor, reseller or an IEI sales representative at
[email protected] or visit the IEI website (http://www.ieiworld.com.tw)
to find out more about the available chassis.
5.5.2 Motherboard Installation
To install the KINO-9452 motherboard into the chassis, please refer to the reference
material that came with the chassis.
5.6 Internal Peripheral Device Connections
5.6.1 Peripheral Device Cables
The cables listed in Table 5-7 are shipped with the KINO-9452.
Quantity
Type
1
IDE cable
1
Dual RS-232 cable
2
SATA drive cables
1
SATA drive power cable
Table 5-7: IEI Provided Cables
Optional cables are listed below:
USB cable (dual port)
USB cable (four port)
RS-232/422/485 cable
Page 78
KINO-9452 Mini-ITX SBC
5.6.2 IDE Cable Connection
The IDE flat cable connects to the KINO-9452 to one or two IDE devices. To connect an
IDE HDD to the KINO-9452, please follow the instructions below.
Step 1: Locate the IDE connector. The location/s of the IDE device connector/s is/are
shown in Chapter 3.
Step 2: Insert the connector. Connect the IDE cable connector to the onboard
connector. See Figure 5-13. A key on the front of the cable connector ensures it
can only be inserted in one direction.
Figure 5-13: IDE Cable Connection
Step 3: Connect the cable to an IDE device. Connect the two connectors on the other
side of the cable to one or two IDE devices. Make sure that pin 1 on the cable
corresponds to pin 1 on the connector.Step 0:
Page 79
KINO-9452 Mini-ITX SBC
5.6.3 Dual RS-232 Cable Connection
The dual RS-232 cable consists of two connectors attached to two independent cables.
Each cable is then attached to a D-sub 9 male connector that is mounted onto a bracket.
To install the dual RS-232 cable, please follow the steps below.
Step 1: Locate the connectors. The locations of the RS-232 connectors are shown in
Chapter 3.
Step 2: Insert the cable connectors. Insert one connector into each serial port box
headers. See Figure 5-14. A key on the front of the cable connectors ensures
the connector can only be installed in one direction.
Figure 5-14: Dual RS-232 Cable Installation
Step 3: Secure the bracket. The dual RS-232 connector has two D-sub 9 male
connectors secured on a bracket. To secure the bracket to the chassis please
refer to the reference material that came with the chassisStep 0:
Page 80
KINO-9452 Mini-ITX SBC
5.6.4 SATA Drive Connection
The KINO-9452 is shipped with two SATA drive cables and one SATA drive power cable.
To connect the SATA drives to the connectors, please follow the steps below.
Step 1: Locate the connectors. The locations of the SATA drive connectors are shown
in Chapter 3.
Step 2: Insert the cable connector. Press the clip on the connector at the end of the
SATA cable and insert the cable connector into the onboard SATA drive
connector. See Figure 5-15.
Figure 5-15: SATA Drive Cable Connection
Step 3: Connect the cable to the SATA disk. Connect the connector on the other end
of the cable to the connector at the back of the SATA drive. See Figure 5-16.
Step 4: Connect the SATA power cable. Connect the SATA power connector to the
back of the SATA drive. See Figure 5-16. Step 0:
Page 81
KINO-9452 Mini-ITX SBC
Figure 5-16: SATA Power Drive Connection
5.7 External Peripheral Interface Connection
The following external peripheral devices can be connected to the external peripheral
interface connectors.
Audio devices
RJ-45 Ethernet cable
USB devices
VGA monitors
Serial port devices
Mouse and keyboard
HDTV devices
To install these devices, connect the corresponding cable connector from the actual
device to the corresponding KINO-9452 external peripheral interface connector making
sure the pins are properly aligned.
Page 82
KINO-9452 Mini-ITX SBC
5.7.1 Audio Connection
Audio signals are interfaced through six phone jack connections. Follow the steps below
to connect audio devices to the KINO-9452.
Step 1: Locate the audio phone jacks. The location of the audio phone jacks are
shown in Chapter 3.
Step 2: Insert audio phone jack plugs. Insert audio phone jack plugs into the audio
phone jacks on the external peripheral interface. See Figure 5-17. Step 0:
Figure 5-17: Audio Connectors
5.7.2 RJ-45 Ethernet and USB Connection
The KINO-9452 has two RJ-45 Ethernet and USB combo connectors on the external
peripheral interface panel for LAN communications and USB device. Follow the steps
below to connect an RJ-45 Ethernet and USB connectors to the KINO-9452.
Step 1: Locate the RJ-45 and USB combo connector. The location of the RJ-45 and
USB combo connector is shown in Chapter 3.
Step 2: Insert an RJ-45 plug. Insert the RJ-45 plug of a LAN into the RJ-45 receptacle
on the external peripheral interface. See Figure 5-18.
Page 83
KINO-9452 Mini-ITX SBC
Step 3: Insert a USB Series "A" plug. Insert the USB Series "A" plug of a device into
the USB Series "A" receptacle on the external peripheral interface. See Figure
5-18. Step 0:
Figure 5-18: RJ-45 Ethernet Connector
5.7.3 VGA Monitor Connection
The KINO-9452 has a single female DB-15 connector on the external peripheral interface
panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor
to the KINO-9452, please follow the instructions below.
Step 1: Locate the female DB-15 connector. The location of the female DB-15
connector is shown in Chapter 3.
Step 2: Align the VGA connector. Align the male DB-15 connector on the VGA screen
cable with the female DB-15 connector on the external peripheral interface.
Step 3: Insert the VGA connector. Once the connectors are properly aligned with the
insert the male connector from the VGA screen into the female connector on the
Page 84
KINO-9452 Mini-ITX SBC
KINO-9452. See Figure 5-19.
Figure 5-19: VGA Connector
Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA
monitor to the external interface by tightening the two retention screws on either
side of the connector. Step 0:
5.7.4 Serial Device Connection
The KINO-9452 has one female DB-9 connector on the external peripheral interface panel
for serial devices. Follow the steps below to connect a serial device to the KINO-9452.
Step 1: Locate the DB-9 connector. The location of the DB-9 connector is shown in
Chapter 3.
Step 2: Insert the serial connector. Insert the DB-9 connector of a serial device into
the DB-9 connector on the external peripheral interface. See Figure 5-20.
Page 85
KINO-9452 Mini-ITX SBC
Figure 5-20: Serial Device Connector
Step 3: Secure the connector. Secure the serial device connector to the external
interface by tightening the two retention screws on either side of the connector.
Step 0:
5.7.5 PS/2 Keyboard/Mouse Connection
The KINO-9452 has a dual PS/2 connector on the external peripheral interface panel. The
dual PS/2 connector is used to connect to a keyboard and mouse to the system. Follow
the steps below to connect a keyboard and mouse to the KINO-9452.
Step 1: Locate the dual PS/2 connector. The location of the dual PS/2 connector is
shown in Chapter 3.
Step 2: Insert the keyboard/mouse connector. Insert a PS/2 keyboard or mouse
connector into the appropriate PS/2 connector on the external peripheral
interface connector. See Figure 5-21. Step 0:
Page 86
KINO-9452 Mini-ITX SBC
Figure 5-21: PS/2 Keyboard/Mouse Connector
5.7.6 HDTV Cable Connection
There is a single mini DIN TV out connector mounted on the SBC as an external
connector. The HDTV cable is able to connect the mini DIN connector on the system with
an external display device. To connect an external display device to the system through
the mini DIN connector with the HDTV cable, please follow the instruction below.
Step 1: Locate the TV-OUT DIN connector. The location of the TV-OUT DIN connector
is shown in Chapter 4.
Step 2: Align the connectors. Align the connector on the end of the HDTV cable with
the mini DIN connector. See Figure 5-22.
Page 87
KINO-9452 Mini-ITX SBC
Figure 5-22: HDTV Cable Connector
Step 3: Insert HDTV cable connector. Once aligned, gently insert the HDTV cable
connector into the on-board connector.
Step 4: Connect the cables to the display device. Connect the S-video connector and
the Pb, Y and Pr component connectors on the other end of the S-video cables
to the respective connectors on the display device. Step 0:
Page 88
KINO-9452 Mini-ITX SBC
Chapter
6
6 AMI BIOS
Page 89
KINO-9452 Mini-ITX SBC
6.1 Introduction
A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup
program allows users to modify the basic system configuration. This chapter describes
how to access the BIOS setup program and the configuration options that may be
changed.
6.1.1 Starting Setup
The AMI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the DELETE key as soon as the system is turned on or
2. Press the DELETE key when the “Press Del to enter SETUP” message
appears on the screen. 0.
If the message disappears before, restart the computer and try again.
6.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the “+” and “-“ keys to
change entries, press F1 for help and press ESC to quit. Navigation keys are shown in.
Key
Function
Up arrow
Move to previous item
Down arrow
Move to next item
Left arrow
Move to the item on the left hand side
Right arrow
Move to the item on the right hand side
Esc key
Main Menu – Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
“+” key
Increase the numeric value or make changes
“-“ key
Decrease the numeric value or make changes
F1 key
General help, only for Status Page Setup Menu and Option
Page Setup Menu
Page 90
KINO-9452 Mini-ITX SBC
F2 /F3 key
Change color from total 16 colors. F2 to select color
forward.
F10 key
Save all the CMOS changes, only for Main Menu
Table 6-1: BIOS Navigation Keys
6.1.3 Getting Help
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press ESC or
the F1 key again.
6.1.4 Unable to Reboot after Configuration Changes
If the computer cannot boot after changes to the system configuration is made, CMOS
defaults. Use the jumper described in Chapter 5, Section 5.4.2.
6.1.5 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:
Main Changes the basic system configuration.
Advanced Changes the advanced system settings.
PCIPnP Changes the advanced PCI/PnP Settings
Boot Changes the system boot configuration.
Security Sets User and Supervisor Passwords.
Chipset Changes the chipset settings.
Exit Selects exit options and loads default settings
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
6.2 Main
When the BIOS Setup program is entered, the Main menu (BIOS Menu 1) appears. The
Main menu gives an overview of the basic system information.
Page 91
KINO-9452 Mini-ITX SBC
BIOS Menu 1: Main
System Overview
The System Overview lists a brief summary of different system components. The fields in
System Overview cannot be changed. The items shown in the system overview include:
AMI BIOS: Displays auto-detected BIOS information
o
o
o
Version:
Current BIOS version
Build Date: Date the current BIOS version was made
ID:
Installed BIOS ID
Processor: Displays auto-detected CPU specifications
o
o
o
Type: Names the currently installed processor
Speed: Lists the processor speed
Count: The number of CPUs on the motherboard
System Memory: Displays the auto-detected system memory.
o
Size:
Lists memory size
The System Overview field also has two user configurable fields:
System Time [xx:xx:xx]: The system time is set here.
Page 92
KINO-9452 Mini-ITX SBC
System Date [Day xx/xx/xxxx]: The system date is set here.
6.3 Advanced
The Advanced menu (BIOS Menu 2) allows access to the CPU and peripheral device
configuration options through the following sub-menus:
WARNING:
Setting the wrong values in the sections below may cause the system to
malfunction. Make sure that the settings made are compatible with the
hardware.
CPU Configuration (see Section 6.3.1)
IDE Configuration (see Section 6.3.2)
SuperIO Configuration (see Section 6.3.3)
Hardware Health Configuration (see Section 6.3.4)
Power Configuration (see Section 6.3.5)
Remote Access Configuration (see Section 6.3.6)
USB Configuration (see Section 6.3.7)
Page 93
KINO-9452 Mini-ITX SBC
BIOS Menu 2: Advanced
6.3.1 CPU Configuration
The CPU Configuration menu (BIOS Menu 3) shows detailed CPU specifications and
CPU configuration options.
Page 94
KINO-9452 Mini-ITX SBC
BIOS Menu 3: CPU Configuration
The CPU Configuration menu (BIOS Menu 3) lists the following CPU details:
Manufacturer: Lists the name of the CPU manufacturer
Brand String: Lists the brand name of the CPU being used
Frequency: Lists the CPU processing speed
FSB Speed: Lists the FSB speed
Cache L1: Lists the CPU L1 cache size
Cache L2: Lists the CPU L2 cache size
6.3.2 IDE Configuration
The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the
IDE devices installed in the system.
Page 95
KINO-9452 Mini-ITX SBC
BIOS Menu 4: IDE Configuration
ATA/IDE Configuration [Compatible]
The ATA/IDE Configuration BIOS option allows the user to configure the ATA/IDE device
mode.
Disable all ATA/IDE ports. No Primary/Secondary IDE
Disabled
mode is presented for configuration
Compatible
DEFAULT
Up to 4 HDDs can be used, two for SATA and the other
for PATA IDE. If this option is selected, “Legacy IDE
Channels” option is presented for configuration.
Enhanced
If this option is selected, “Configure SATA as” and
“Configure SATA channels” options are presented for
configuration.
Page 96
KINO-9452 Mini-ITX SBC
Legacy IDE Channels [SATA Pri, PATA Sec]
Use the Legacy IDE Channels option configures PATA and SATA resources for operating
systems that require legacy IDE operation.
SATA Only
Enable up to two SATA devices
Reserved
The legacy IDE channels are reserved
SATA
Pri,
DEFAULT
This option allows the system to access the SATA
PATA Sec
devices before the primary IDE devices
PATA Only
Enable the two primary IDE devices. Select this option
only when the two primary IDE devices are available
IDE Master and IDE Slave
When entering setup, BIOS auto detects the presence of IDE devices. This displays the
status of the auto detected IDE devices. The following IDE devices are detected and are
shown in the IDE Configuration menu:
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the
IDE devices installed in the system. If an IDE device is detected, and one of the above
listed four BIOS configuration options are selected, the IDE configuration options shown in
Section 6.3.2.1 appear.
6.3.2.1 IDE Master, IDE Slave
IDE Master and IDE Slave configuration options for both primary and secondary IDE
devices are shown in the BIOS menu below.
Page 97
KINO-9452 Mini-ITX SBC
BIOS Menu 5: IDE Master and IDE Slave Configuration
Type [Auto]
The Type BIOS option determines the type of device that the AMIBIOS attempts to boot
from after the Power-On Self-Test (POST) has completed.
Selecting this value prevents the BIOS from searching
Not Installed
for an IDE disk drive on the specified channel.
Auto
DEFAULT
This selection enables the BIOS to auto detect the
IDE disk drive type attached to the specified channel.
This setting should be used if an IDE hard disk drive is
attached to the specified channel.
CD/DVD
The CD/DVD option specifies that an IDE CD-ROM
drive is attached to the specified IDE channel. The
BIOS does not attempt to search for other types of
Page 98
KINO-9452 Mini-ITX SBC
IDE disk drives on the specified channel.
This option specifies an ATAPI Removable Media
ARMD
Device. These include, but are not limited to:
ZIP
LS-120
LBA/Large Mode [Auto]
The LBA/Large Mode BIOS option disables or auto detects LBA (Logical Block
Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the
maximum drive capacity is 137 GB.
This selection prevents the BIOS from using the LBA
Disabled
mode control on the specified channel.
Auto
DEFAULT
This option allows the BIOS to auto detect the LBA mode
control on the specified channel.
Block (Multi Sector Transfer) [Auto]
Selecting this option prevents the BIOS from using
Disabled
Multi-Sector Transfer on the specified channel. The data
to and from the device occurs one sector at a time.
Auto
DEFAULT
Selecting this value to allows the BIOS to auto detect the
device support for Multi-Sector Transfers on the specified
channel. If supported. Select this value to allow the BIOS
to auto detect the number of sectors per block for transfer
from the hard disk drive to the memory. The data transfer
to and from the device occurs multiple sectors at a time.
Page 99
KINO-9452 Mini-ITX SBC
PIO Mode [Auto]
The PIO Mode option selects the IDE PIO (Programmable I/O) mode program timing
cycles between the IDE drive and the programmable IDE controller. As the PIO mode
increases, the cycle time decreases.
Auto
DEFAULT
This setting allows the BIOS to auto detect the PIO mode. Use
this value if the IDE disk drive support cannot be determined.
0
PIO mode 0 selected with a maximum transfer rate of 3.3MBps
1
PIO mode 1 selected with a maximum transfer rate of 5.2MBps
2
PIO mode 2 selected with a maximum transfer rate of 8.3MBps
3
PIO mode 3 selected with a maximum transfer rate of 11.1MBps
4
PIO mode 4 selected with a maximum transfer rate of 16.6MBps
(This setting generally works with all hard disk drives
manufactured after 1999. For other disk drives, such as IDE
CD-ROM drives, check the specifications of the drive.)
DMA Mode [Auto]
The DMA Mode BIOS selection adjusts the DMA mode options.
Auto
DEFAULT
The BIOS auto detects the DMA mode. Use this value if the
IDE disk drive support cannot be determined.
S.M.A.R.T [Auto]
Self-Monitoring Analysis and Reporting Technology (SMART) feature can help predict
impending drive failures. The S.M.A.R.T BIOS option enables or disables this function.
Auto
Page 100
DEFAULT
BIOS to auto detects if the hard disk drive supports
KINO-9452 Mini-ITX SBC
S.M.A.R.T. Use this setting if the IDE disk drive support
cannot be determined.
Select this value to prevent the BIOS from using the
Disabled
SMART feature.
Select this value to allow the BIOS to use the SMART
Enabled
feature on support hard disk drives.
32Bit Data Transfer [Enabled]
The 32Bit Data Transfer BIOS option enables or disables 32-bit data transfers.
Prevents the BIOS from using 32-bit data transfers.
Disabled
Enabled
DEFAULT
Allows BIOS to use 32-bit data transfers on support hard
disk drives.
6.3.3 Super IO Configuration
The Super IO Configuration menu (BIOS Menu 6) sets or changes the configurations for
the FDD controllers, parallel ports and serial ports.
Page 101
KINO-9452 Mini-ITX SBC
BIOS Menu 6: Super IO Configuration
Serial Port1 Address [3F8/IRQ4]
The Serial Port1 Address option allows BIOS to select the Serial Port 1 base address.
No base address is assigned to Serial Port 1
Disabled
3F8/IRQ4
DEFAULT
Serial Port 1 I/O port address is 3F8 and the interrupt
address is IRQ4
3E8/IRQ4
Serial Port 1 I/O port address is 3E8 and the interrupt
address is IRQ4
2E8/IRQ3
Serial Port 1 I/O port address is 2E8 and the interrupt
address is IRQ3
Serial Port2 Address [2F8/IRQ3]
The Serial Port2 Address option allows BIOS to select the Serial Port 2 base address.
Page 102
KINO-9452 Mini-ITX SBC
No base address is assigned to Serial Port 2
Disabled
2F8/IRQ3
Serial Port 2 I/O port address is 3F8 and the interrupt
DEFAULT
address is IRQ3
Serial Port 2 I/O port address is 3E8 and the interrupt
3E8/IRQ4
address is IRQ4
Serial Port 2 I/O port address is 2E8 and the interrupt
2E8/IRQ3
address is IRQ3
Serial Port3 Address [3E8]
This option allows BIOS to select the base addresses for serial port 3
No base address is assigned to serial port 3
Disabled
3E8
DEFAULT
Serial port 3 I/O port address is 3E8
2E8
Serial port 3 I/O port address is 2E8
2F0
Serial port 3 I/O port address is 2F0
2E0
Serial port 3 I/O port address is 2E0
Select RS232 or RS422/RS485 [RS232]
The Select RS232 or RS422/RS485 selection sets the mode for serial port 3.
Serial port 3 is set to RS-232
RS232
RS422/RS485
DEFAULT
Serial port 3 is set to RS-422 or RS-485
Serial Port4 Address [2E8]
This option allows BIOS to select the base addresses for serial port 4.
Disabled
No base address is assigned to serial port 4
Page 103
KINO-9452 Mini-ITX SBC
Serial port 4 I/O port address is 3E8
3E8
2E8
DEFAULT
Serial port 4 I/O port address is 2E8
2F0
Serial port 4 I/O port address is 2F0
2E0
Serial port 4 I/O port address is 2E0
6.3.4 Hardware Health Configuration
The Hardware Health Configuration menu (BIOS Menu 7) shows the operating
temperature, fan speeds and system voltages.
BIOS Menu 7: Hardware Health Configuration
CPU FAN Mode Setting: [Full On mode]
The CPU FAN Mode Setting has the following options:
Page 104
KINO-9452 Mini-ITX SBC
Full On mode
DEFAULT
If selected, there are no additional configurable
options.
Automatic
If selected, the following options will appear with
Mode
values that can be configured:
CPU Temp. Limit of OFF
CPU Temp. Limit of Start
CPU Temp. Limit of Full
CPU Fan Start PWM
Slop PWM 1:
0 PWM, 1 PWM (Default), 2 PWM, 4 PWM, 8
PWM, 16 PWM, 32 PWM or 64 PWM
PWM Manually
If selected, the following option will appear with
mode
values that can be configured:
CPU Fan PWM Control
The following system parameters and values are shown. The system parameters that are
monitored are:
System Temperatures: The following system temperatures are monitored
o
o
CPU Temperature
System Temperature
Fan Speeds: The CPU cooling fan speed is monitored.
o
o
CPU Fan Speed
System Fan Speed
Voltages: The following system voltages are monitored
o
o
o
o
CPU Core
+2.5V
+3.30V
+5.00V
Page 105
KINO-9452 Mini-ITX SBC
o
o
o
o
o
+12.0V
GMCH (1.5V)
1.05V
5VSB
VBAT
6.3.5 Power Configuration
The Power Configuration menu (BIOS Menu 8) configures the Advanced Configuration
and Power Interface (ACPI) and Power Management (APM) options.
BIOS Menu 8: Power Configuration
AT/ATX Power [by H/W]
Use the AT/ATX Power BIOS option to select the power supply that is connected to the
system.
Page 106
AT power
An AT power supply is connected to the system
ATX power
An ATX power supply is connected to the system
KINO-9452 Mini-ITX SBC
By H/W
DEFAULT
The power mode is selected by the on-board jumpers
6.3.5.1 ACPI Configuration
Use the ACPI Configuration menu (BIOS Menu 9) to select the ACPI state when the
system is suspended.
BIOS Menu 9: General ACPI Configuration [Advanced\ ACPI Configuration]
Suspend mode [S1 (POS)]
Use the Suspend Mode option to specify the sleep state the system enters when it is not
being used.
S1 (POS)
DEFAULT
The system enters S1(POS) sleep state. The system
appears off. The CPU is stopped; RAM is refreshed; the
system is running in a low power mode.
Page 107
KINO-9452 Mini-ITX SBC
The system enters a S3(STR) sleep state. The CPU has
S3 (STR)
no power; RAM is in slow refresh; the power supply is in a
reduced power mode.
6.3.5.2 APM Configuration
Use the APM Configuration menu (BIOS Menu 10) to select the advanced power
management.
BIOS Menu 10: APM Configuration
Power Button Mode [On/Off]
Use the Power Button Mode BIOS to specify how the power button functions.
On/Off
DEFAULT
When the power button is pressed the system is either
turned on or off
Suspend
When the power button is pressed the system goes into
suspend mode
Page 108
KINO-9452 Mini-ITX SBC
Restore on AC Power Loss by IO [Last State]
The Restore on AC Power Loss by IO BIOS option specifies what state the system
returns to if there is a sudden loss of power to the system.
Power Off
The system remains turned off
Power On
The system turns on
Last State
DEFAULT
The system returns to its previous state. If it was on, it
turns itself on. If it was off, it remains off.
Resume on Keyboard/Mouse [Disabled]
Use the Resume on Keyboard/Mouse BIOS option to enable activity on either the
keyboard or mouse to rouse the system from a suspend or standby state. That is, the
system is roused when the mouse is moved or a button on the keyboard is pressed.
Disabled
DEFAULT
Wake event not generated by activity on the
keyboard or mouse
Wake event generated by activity on the keyboard
Resume On
KeyBoard
Wake event generated by activity on the mouse
Resume On
Mouse
Wake event generated by activity on the keyboard or
Enabled
mouse
Resume on PME# [Disabled]
The Resume on PME# BIOS option specifies if the system will be roused from a
suspended or standby state when there is activity on the PCI PME (power management
event) controller.
Disabled
DEFAULT
Wake event not generated by PCI PME controller
Page 109
KINO-9452 Mini-ITX SBC
activity
Wake event generated by PCI PME controller activity
Enabled
Resume On PCI-Express WAKE# [Enabled]
The Resume On PCI-Express WAKE# BIOS option specifies if the system will be roused
from a suspended or standby state when there is activity on the PCI-Express controller.
Enabled
DEFAULT
Wake event generated by PCI-Express controller
activity
Wake event not generated by PCI-Express controller
Disabled
activity
Resume On RTC Alarm [Disabled]
The Resume On RTC Alarm determines when the computer will be roused from a
suspended state.
Disabled
DEFAULT
The real time clock (RTC) cannot generate a wake
event
Enabled
If selected, the following will appear with values that
can be selected:
RTC Alarm Date (Days)
RTC Alarm Time
After setting the alarm, the computer will turn itself on
from a suspend state when the alarm goes off.
6.3.6 Remote Access Configuration
Use the Remote Access Configuration menu (BIOS Menu 11) to configure remote
access parameters. The Remote Access Configuration is an AMIBIOS feature and
Page 110
KINO-9452 Mini-ITX SBC
allows a remote host running a terminal program to display and configure the BIOS
settings.
BIOS Menu 11: Remote Access Configuration [Advanced]
Remote Access [Disabled]
Use the Remote Access option to enable or disable access to the remote functionalities
of the system.
Disabled
Enabled
DEFAULT
Remote access is disabled.
Remote access configuration options shown below
appear:
Serial Port Number
Serial Port Mode
Page 111
KINO-9452 Mini-ITX SBC
Redirection after BIOS POST
Terminal Type
These configuration options are discussed below.
6.3.7 USB Configuration
Use the USB Configuration menu (BIOS Menu 12) to read USB configuration
information and configure the USB settings.
BIOS Menu 12: USB Configuration
USB Configuration
The USB Configuration field shows the system USB configuration. The items listed are:
Module Version: x.xxxxx.xxxxx
Page 112
KINO-9452 Mini-ITX SBC
USB Devices Enabled
The USB Devices Enabled field lists the USB devices that are enabled on the system
USB Function [Enabled]
Use the USB Function BIOS option to enable or disable USB function support.
USB function support disabled
Disabled
Enabled
DEFAULT
USB function support enabled
USB 2.0 Controller [Enabled]
Use the USB 2.0 Controller BIOS option to enable or disable the USB 2.0 controller
Enabled
DEFAULT
USB 2.0 controller enabled
USB 2.0 controller disabled
Disabled
Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support.
Normally if this option is not enabled, any attached USB mouse or USB keyboard does not
become available until a USB compatible operating system is fully booted with all USB
drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard
can control the system even when there is no USB driver loaded onto the system.
Legacy USB support disabled
Disabled
Enabled
Auto
DEFAULT
Legacy USB support enabled
Legacy USB support disabled if no USB devices are
connected
Page 113
KINO-9452 Mini-ITX SBC
USB2.0 Controller Mode [FullSpeed]
Use the USB2.0 Controller Mode option to set the speed of the USB2.0 controller.
FullSpeed
DEFAULT
HiSpeed
The controller is capable of operating at 12Mb/s
The controller is capable of operating at 480Mb/s
6.4 PCI/PnP
Use the PCI/PnP menu (BIOS Menu 13) to configure advanced PCI and PnP settings.
WARNING!
Setting wrong values for the BIOS selections in the PCIPnP BIOS menu
may cause the system to malfunction.
Page 114
KINO-9452 Mini-ITX SBC
BIOS Menu 13: PCI/PnP Configuration
IRQ# [Available]
Use the IRQ# address to specify what IRQs can be assigned to a particular peripheral
device.
Available
DEFAULT
The specified IRQ is available to be used by
PCI/PnP devices
The specified IRQ is reserved for use by Legacy ISA
Reserved
devices
Available IRQ addresses are:
IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ 11
IRQ 14
IRQ 15
DMA Channel# [Available]
Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP
device.
Available
DEFAULT
The specified DMA is available to be used by
PCI/PnP devices
Reserved
The specified DMA is reserved for use by Legacy
ISA devices
Page 115
KINO-9452 Mini-ITX SBC
Available DMA Channels are:
DM Channel 0
DM Channel 1
DM Channel 3
DM Channel 5
DM Channel 6
DM Channel 7
Reserved Memory Size [Disabled]
Use the Reserved Memory Size BIOS option to specify the amount of memory that
should be reserved for legacy ISA devices.
Disabled
DEFAULT
No memory block reserved for legacy ISA devices
16K
16KB reserved for legacy ISA devices
32K
32KB reserved for legacy ISA devices
64K
54KB reserved for legacy ISA devices
6.5 Boot
Use the Boot menu (BIOS Menu 14) to configure system boot options.
Page 116
KINO-9452 Mini-ITX SBC
BIOS Menu 14: Boot
6.5.1 Boot Settings Configuration
Use the Boot Settings Configuration menu (BIOS Menu 15) to configure advanced
system boot options.
Page 117
KINO-9452 Mini-ITX SBC
BIOS Menu 15: Boot Settings Configuration
Quick Boot [Enabled]
Use the Quick Boot BIOS option to make the computer speed up the boot process.
No POST procedures are skipped
Disabled
Enabled
DEFAULT
Some POST procedures are skipped to decrease
the system boot time
Quiet Boot [Enabled]
Use the Quiet Boot BIOS option to select the screen display when the system boots.
Normal POST messages displayed
Disabled
Enabled
Page 118
DEFAULT
OEM Logo displayed instead of POST messages
KINO-9452 Mini-ITX SBC
AddOn ROM Display Mode [Force BIOS]
Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory)
messages to be displayed.
Force BIOS
DEFAULT
The system forces third party BIOS to display
during system boot.
The system displays normal information during
Keep Current
system boot.
Bootup Num-Lock [On]
Use the Bootup Num-Lock BIOS option to specify if the number lock setting must be
modified during boot up.
Does not enable the keyboard Number Lock automatically. To
Off
use the 10-keys on the keyboard, press the Number Lock key
located on the upper left-hand corner of the 10-key pad. The
Number Lock LED on the keyboard lights up when the Number
Lock is engaged.
On
DEFAULT
Allows the Number Lock on the keyboard to be enabled
automatically when the computer system boots up. This allows
the immediate use of the 10-key numeric keypad located on
the right side of the keyboard. To confirm this, the Number
Lock LED light on the keyboard is lit.
Boot From LAN Support [Disabled]
The BOOT From LAN Support option enables the system to be booted from a remote
system.
Page 119
KINO-9452 Mini-ITX SBC
Disabled
DEFAULT
Cannot be booted from a remote system through the
LAN
Enabled
Can be booted from a remote system through the
LAN
6.6 Security
Use the Security menu (BIOS Menu 16) to set system and user passwords.
BIOS Menu 16: Security
Change Supervisor Password
Use the Change Supervisor Password to set or change a supervisor password. The
default for this option is Not Installed. If a supervisor password must be installed, select
Page 120
KINO-9452 Mini-ITX SBC
this field and enter the password. After the password has been added, Install appears
next to Change Supervisor Password.
Change User Password
Use the Change User Password to set or change a user password. The default for this
option is Not Installed. If a user password must be installed, select this field and enter the
password. After the password has been added, Install appears next to Change User
Password.
6.7 Chipset
Use the Chipset menu (BIOS Menu 17) to access the NorthBridge and SouthBridge
configuration menus
WARNING!
Setting the wrong values for the Chipset BIOS selections in the Chipset
BIOS menu may cause the system to malfunction.
Page 121
KINO-9452 Mini-ITX SBC
BIOS Menu 17: Chipset
6.7.1 North Bridge Configuration
Use the North Bridge Configuration menu (BIOS Menu 18) to configure the Northbridge
chipset.
Page 122
KINO-9452 Mini-ITX SBC
BIOS Menu 18: North Bridge Chipset Configuration
Memory Hole [Disabled]
Use the Memory Hole option to reserve memory space between 15MB and 16MB for ISA
expansion cards that require a specified area of memory to work properly. If an older ISA
expansion card is used, please refer to the documentation that came with the card to see if
it is necessary to reserve the space.
Disabled
15MB – 16MB
DEFAULT
Memory is not reserved for ISA expansion cards
Between 15MB and 16MB of memory is reserved for
ISA expansion cards
Boots Graphics Adapter Priority [PCI/IGD]
Use the Boots Graphics Adapter Priority option to select the graphics controller used as
the primary boot device. Select either an integrated graphics controller (IGD) or a
combination of PCI graphics controller, a PCI express (PEG) controller or an IGD.
Configuration options are listed below:
Page 123
KINO-9452 Mini-ITX SBC
IGD
PCI/IGD
DEFAULT
Internal Graphics Mode Select [Enable, 8MB]
Use the Internal Graphic Mode Select option to specify the amount of system memory
that can be used by the Internal graphics device.
Disable
1MB of memory used by internal graphics device
Enable, 1MB
Enable, 8MB
DEFAULT
8MB of memory used by internal graphics device
DVMT Mode Select [DVMT Mode]
Use the DVMT Mode Select option to select the Intel Dynamic Video Memory Technology
(DVMT) operating mode.
A fixed portion of graphics memory is reserved as
Fixed Mode
graphics memory.
DVMT Mode
DEFAULT
Graphics
memory
is
dynamically
allocated
according to the system and graphics needs.
Combo Mode
A fixed portion of graphics memory is reserved as
graphics memory. If more memory is needed,
graphics
memory
is
dynamically
allocated
according to the system and graphics needs.
DVMT/FIXED Memory [128MB]
Use the DVMT/FIXED Memory option to specify the maximum amount of memory that
can be allocated as graphics memory. This option can only be configured for if DVMT
Mode or Fixed Mode is selected in the DVMT Mode Select option. If Combo Mode is
Page 124
KINO-9452 Mini-ITX SBC
selected, the maximum amount of graphics memory is 128MB. Configuration options are
listed below.
64MB
128MB
DEFAULT
Maximum DVMT
Boot Display Device [Auto]
Use the Boot Display Device option to select the display device used by the system
when it boots. Configuration option is listed below.
Auto
DEFAULT
CRT
TV
LFP
Flat Panel Type [1024*768]
Use the Flat Panel Type option to select the type of flat panel connected to the system.
Configuration options are listed below.
1024x768 18b
1024x768 24b
1280x1024 36b
1280x1024 48b
1366x768 36b
1366x768 348b
1600x1200 36b
1600x1200 48b
1680x1050 36b
1680x1050 48b
1920x1080 36b
1920x1080 48b
1920x1200 36b
1920x1200 48b
Page 125
KINO-9452 Mini-ITX SBC
BY HARDWARE
DEFAULT
Local Flat Panel Scaling [Auto]
Use the Local Flat Panel Scaling option to select the method of scaling for the flat panel
screen attached to the system.
Auto
DEFAULT
Scaling is automatic
Forced Scaling
Scaling is forced
Disabled
Scaling is disabled
TV Standard [VBIOS-Default]
Use the TV Standard option to select the standard of the television connected to the
system. The configuration options are listed below.
VBIOS-Default
DEFAULT
NTSC
PAL
6.7.2 South Bridge Configuration
The SouthBridge Configuration menu (BIOS Menu 19) the Southbridge chipset to be
configured.
Page 126
KINO-9452 Mini-ITX SBC
BIOS Menu 19:South Bridge Chipset Configuration
ASF Support [Enabled]
Use the ASF Support BIOS option to control the system’s ability to connect to a remote
management server.
Enabled
DEFAULT
The Alert Standard Format (ASF) controller is activated
and can communicate with a remote management
server.
Audio Controller [Azalia]
The Audio Controller option enables or disables the High Definition Audio CODEC.
Azalia
DEFAULT
The Intel High Definition Audio controller automatically
detected and enabled
Disabled
The onboard High Definition Audio controller is disabled
Page 127
KINO-9452 Mini-ITX SBC
6.8 Exit
Use the Exit menu (BIOS Menu 20) to load default BIOS values, optimal failsafe values
and to save configuration changes.
BIOS Menu 20:Exit
Save Changes and Exit
Use the Save Changes and Exit option to save the changes made to the BIOS options
and to exit the BIOS configuration setup program.
Discard Changes and Exit
Use the Discard Changes and Exit option to exit the BIOS configuration setup program
without saving the changes made to the system.
Page 128
KINO-9452 Mini-ITX SBC
Discard Changes
Use the Discard Changes option to discard the changes and remain in the BIOS
configuration setup program.
Load Optimal Defaults
Use the Load Optimal Defaults option to load the optimal default values for each of the
parameters on the Setup menus. F9 key can be used for this operation.
Load Failsafe Defaults
Use the Load Failsafe Defaults option to load failsafe default values for each of the
parameters on the Setup menus. F8 key can be used for this operation.
Page 129
KINO-9452 Mini-ITX SBC
Chapter
7
7
Page 130
Software Driver
KINO-9452 Mini-ITX SBC
7.1 Available Software Drivers
NOTE:
The content of the CD may vary throughout the life cycle of the product and
is subject to change without prior notice. Visit the IEI website or contact
technical support for the latest updates.
The KINO-9452 motherboard has the following software drivers:
Intel Chipset Driver Installation
VGA Utilities Driver
LAN Driver (for GbE LAN) Installation
RealTek Audio Driver (ALC883) Installation
SATA Driver Installation
All drivers can be found on the CD that came with the motherboard. To install the drivers
please follow the instructions in the sections below.
7.2 Chipset Driver Installation
To install the chipset driver, please follow the steps below:
Step 1: Insert the CD into the system that contains the KINO-9452 board. Open the
1-INF directory and locate the icon for the infinst_autol.exe installation file.
Once located, use the mouse to double click the icon.
Step 2: The “InstallShield Wizard Preparation Screen” in Figure 7-1 appears.
Page 131
KINO-9452 Mini-ITX SBC
Figure 7-1: InstallShield Wizard Preparation Screen
Step 3: The “Welcome” window in Figure 7-2 appears next.
Figure 7-2: Welcome Screen
Step 4: Click “NEXT” and the license agreement shown in Figure 7-3 appears.
Page 132
KINO-9452 Mini-ITX SBC
Figure 7-3: License Agreement
Step 5: Agree to the license terms by clicking “YES”. The “Readme” in Figure 7-4
appears.
Figure 7-4: Readme Information
Step 6: Click “YES”. The driver is installed on the computer. After the installation is
complete, the installation complete screen shown in Figure 7-5 appears. Select
Page 133
KINO-9452 Mini-ITX SBC
the preferred option and click “FINISH” to complete the installation process.
Step 0:
Figure 7-5: Restart the Computer
7.3 VGA Driver
To install the VGA driver, please follow the steps below:
Step 1: Insert the Utility CD that came with the motherboard into the system CD drive.
Step 2: Open the X:\2-VGA\WIN2K_XP directory (where X:\ is the system CD drive)
and double-click the win2k_xp1420.exe installation file.
Step 3: The Starting Install Shield Wizard appears (Figure 7-6).
Page 134
KINO-9452 Mini-ITX SBC
Figure 7-6: Starting Install Shield Wizard Screen
Step 4: The Preparing Setup window appears next (Figure 7-7).
Figure 7-7: Preparing Setup Screen
Page 135
KINO-9452 Mini-ITX SBC
Step 5: A Welcome screen shown in Figure 7-8 appears. Click NEXT to continue the
installation.
Figure 7-8: VGA Driver Installation Welcome Screen
Step 6: A license agreement shown in Figure 7-9 appears. Read through the license
agreement.
Figure 7-9: VGA Driver License Agreement
Step 7: Accept the terms and conditions stipulated in the license agreement by clicking
Page 136
KINO-9452 Mini-ITX SBC
the “YES” button (Figure 7-9). The installation notice shown in Figure 7-10
appears.
Figure 7-10: VGA Driver Installing Notice
Step 8: After the driver installation process is complete, a confirmation screen shown in
Figure 7-11 appears.
Figure 7-11: VGA Driver Installation Complete
Step 9: The confirmation screen shown in Figure 7-11 allows user to restart the
computer immediately after the installation is complete or to restart the computer
later. For the settings to take effect the computer must be restarted. Once
decided when to restart the computer, click the “FINISH” button. Step 0:
Page 137
KINO-9452 Mini-ITX SBC
7.4 Broadcom LAN Driver (for GbE LAN) Installation
To install the Broadcom LAN driver, please follow the steps below.
Step 1: Open Windows Control Panel (Figure 7-12).
Figure 7-12: Access Windows Control Panel
Step 2: Double click the System icon (Figure 7-13).
Page 138
KINO-9452 Mini-ITX SBC
Figure 7-13: Double Click the System Icon
Step 3: Double click the Device Manager tab (Figure 7-14).
Figure 7-14: Double Click the Device Manager Tab
Step 4: A list of system hardware devices appears (Figure 7-15).
Page 139
KINO-9452 Mini-ITX SBC
Figure 7-15: Device Manager List
Step 5: Double click the listed device that has question marks next to it. (This means
Windows does not recognize the device).
Step 6: The Device Driver Wizard appears (Figure 7-16). Click NEXT to continue.
Page 140
KINO-9452 Mini-ITX SBC
Figure 7-16: Search for Suitable Driver
Step 7: Select “Specify a Location” in the Locate Driver Files window (Figure 7-17).
Click NEXT to continue.
Page 141
KINO-9452 Mini-ITX SBC
Figure 7-17: Locate Driver Files
Step 8: Select the proper OS folder under the “X:\3-LAN\BROADCOM BCM57xx
Drivers” directory (Figure 7-18) in the location browsing window, where “X:\” is
the system CD drive.
Figure 7-18: Location Browsing Window
Step 9: Click OK to continue. A driver files location menu window appears. Click NEXT to
Page 142
KINO-9452 Mini-ITX SBC
continue. The driver is installed.Step 0:
7.5 RealTek HD Audio Driver (ALC883) Installation
To install the Realtek High Definition (HD) Audio driver, please follow the steps below.
Step 1: Open Windows Control Panel (Figure 7-12).
Figure 7-19: Access Windows Control Panel
Step 2: Double click the System icon (Figure 7-13).
Page 143
KINO-9452 Mini-ITX SBC
Figure 7-20: Double Click the System Icon
Step 3: Double click the Device Manager tab (Figure 7-14).
Page 144
KINO-9452 Mini-ITX SBC
Figure 7-21: Double Click the Device Manager Tab
Step 4: A list of system hardware devices appears (Figure 7-15).
Page 145
KINO-9452 Mini-ITX SBC
Figure 7-22: Device Manager List
Step 5: Double click the listed device that has question marks next to it. (This means
Windows does not recognize the device).
Step 6: The Device Driver Wizard appears (Figure 7-16). Click NEXT to continue.
Page 146
KINO-9452 Mini-ITX SBC
Figure 7-23: Search for Suitable Driver
Step 7: Select “Specify a Location” in the Locate Driver Files window (Figure 7-17).
Click NEXT to continue.
Page 147
KINO-9452 Mini-ITX SBC
Figure 7-24: Locate Driver Files
Step 8: Select “X:\4-AUDIO\AC-KIT883HD\WIN” directory in the location browsing
window, where “X:\” is the system CD drive (Figure 7-18).
Step 9: Click OK to continue. The driver is installed. Step 0:
Step 1: The confirmation screen offers the option of restarting the computer now or later.
For the settings to take effect, the computer must be restarted. Click FINISH to
restart the computer.Step 0:
7.6 Intel Matrix Storage Manager Installation
To install the Intel Matrix Storage Manager driver, please follow the steps below:
Step 1: Insert the Utility CD that came with the motherboard into the system CD drive.
Step 2: Open the X:\5-SATA\ICH7R directory and double-click the iata60_cd.exe
Page 148
KINO-9452 Mini-ITX SBC
installation file.
Step 3: The Preparing Setup window appears ().
Figure 7-25: Preparing Setup Screen
Step 4: A Welcome screen appears. Click NEXT to continue the installation.
Step 5: A license agreement appears. Read through the license agreement.
Step 6: The “Uninstallation Warning” window appears. Click on the NEXT button to
continue.
Step 7: Accept the terms and conditions stipulated in the license agreement by clicking
the “YES” button.
Step 8: The “Choose Destination Location” window appears. Click on the NEXT button to
continue. By default, all installed files are copied to the following path:
<bootdrive>:\Program Files\Intel\Intel(R) Matrix Storage Manager.
Step 9: The “Select Program Folder” window appears. Click on the NEXT button to
continue installing the driver.
Page 149
KINO-9452 Mini-ITX SBC
Step 10: After the driver installation process is complete, a confirmation screen appears.
Step 11: The confirmation screen allows user to restart the computer immediately after
the installation is complete or to restart the computer later. For the settings to
take effect the computer must be restarted. Once decided when to restart the
computer, click the “FINISH” button. Step 0:
Page 150
KINO-9452 Mini-ITX SBC
Appendix
A
A BIOS Configuration
Options
Page 151
KINO-9452 Mini-ITX SBC
A.1 BIOS Configuration Options
Below is a list of BIOS configuration options described in Chapter 6.
System Overview ...................................................................................................92
ATA/IDE Configuration [Compatible]...................................................................96
Legacy IDE Channels [SATA Pri, PATA Sec]......................................................97
IDE Master and IDE Slave .....................................................................................97
Type [Auto] .............................................................................................................98
ZIP 99
LS-120 .....................................................................................................................99
LBA/Large Mode [Auto].........................................................................................99
Block (Multi Sector Transfer) [Auto] ....................................................................99
PIO Mode [Auto].................................................................................................. 100
DMA Mode [Auto]................................................................................................ 100
S.M.A.R.T [Auto].................................................................................................. 100
32Bit Data Transfer [Enabled] ........................................................................... 101
Serial Port1 Address [3F8/IRQ4] ....................................................................... 102
Serial Port2 Address [2F8/IRQ3] ....................................................................... 102
Serial Port3 Address [3E8]................................................................................. 103
Select RS232 or RS422/RS485 [RS232] ............................................................ 103
Serial Port4 Address [2E8]................................................................................. 103
CPU FAN Mode Setting: [Full On mode] .......................................................... 104
CPU Temp. Limit of OFF .................................................................................... 105
CPU Temp. Limit of Start ................................................................................... 105
CPU Temp. Limit of Full ..................................................................................... 105
CPU Fan Start PWM ............................................................................................ 105
Slop PWM 1: ........................................................................................................ 105
CPU Fan PWM Control ....................................................................................... 105
AT/ATX Power [by H/W] ..................................................................................... 106
Suspend mode [S1 (POS)] ................................................................................. 107
Power Button Mode [On/Off] ............................................................................. 108
Page 152
KINO-9452 Mini-ITX SBC
Restore on AC Power Loss by IO [Last State]................................................. 109
Resume on Keyboard/Mouse [Disabled].......................................................... 109
Resume on PME# [Disabled] ............................................................................. 109
Resume On PCI-Express WAKE# [Enabled] .................................................... 110
Resume On RTC Alarm [Disabled].................................................................... 110
RTC Alarm Date (Days) ...................................................................................... 110
RTC Alarm Time .................................................................................................. 110
Remote Access [Disabled]................................................................................. 111
Serial Port Number ............................................................................................. 111
Serial Port Mode.................................................................................................. 111
Redirection after BIOS POST............................................................................. 112
Terminal Type...................................................................................................... 112
USB Configuration.............................................................................................. 112
USB Devices Enabled......................................................................................... 113
USB Function [Enabled]..................................................................................... 113
USB 2.0 Controller [Enabled]............................................................................. 113
Legacy USB Support [Enabled]......................................................................... 113
USB2.0 Controller Mode [FullSpeed] ................................................................ 114
IRQ# [Available]................................................................................................ 115
DMA Channel# [Available] ................................................................................. 115
Reserved Memory Size [Disabled] .................................................................... 116
Quick Boot [Enabled] ......................................................................................... 118
Quiet Boot [Enabled] .......................................................................................... 118
AddOn ROM Display Mode [Force BIOS] ......................................................... 119
Bootup Num-Lock [On] ...................................................................................... 119
Boot From LAN Support [Disabled] .................................................................. 119
Change Supervisor Password........................................................................... 120
Change User Password...................................................................................... 121
Memory Hole [Disabled]..................................................................................... 123
Boots Graphics Adapter Priority [PCI/IGD]...................................................... 123
Internal Graphics Mode Select [Enable, 8MB] ................................................. 124
Page 153
KINO-9452 Mini-ITX SBC
DVMT Mode Select [DVMT Mode]...................................................................... 124
DVMT/FIXED Memory [128MB] .......................................................................... 124
Boot Display Device [Auto]................................................................................ 125
Flat Panel Type [1024*768]................................................................................. 125
Local Flat Panel Scaling [Auto] ......................................................................... 126
TV Standard [VBIOS-Default]............................................................................. 126
ASF Support [Enabled] ...................................................................................... 127
Audio Controller [Azalia].................................................................................... 127
Save Changes and Exit ...................................................................................... 128
Discard Changes and Exit ................................................................................. 128
Discard Changes................................................................................................. 129
Load Optimal Defaults........................................................................................ 129
Load Failsafe Defaults........................................................................................ 129
Page 154
KINO-9452 Mini-ITX SBC
Appendix
B
B DIO Interface
Page 155
KINO-9452 Mini-ITX SBC
B.1 DIO Interface Introduction
The DIO connector on the KINO-9452 is interfaced to GPIO ports on the IT8712F Super
I/O chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs
and digital outputs are generally control signals that control the on/off circuit of external
devices or TTL devices. Data can be read or written to the selected address to enable the
DIO functions.
NOTE:
For further information, please refer to the datasheet for the IT8712F
Super I/O chipset.
B.2 DIO Connector Pinouts
The following table describes how the DIO connector pins are connected to the Super I/O
GPIO port 1.
Pin
Description
Super I/O
Super I/O Pin Description
Pin
1
Ground
N/A
N/A
2
VCC
N/A
N/A
3
Output 3
GP27
General purpose I/O port 2 bit 7.
4
Output 2
GP26
General purpose I/O port 2 bit 6.
5
Output 1
GP25
General purpose I/O port 2 bit 5.
6
Output 0
GP24
General purpose I/O port 2 bit 4.
7
Input 3
GP23
General purpose I/O port 2 bit 3.
8
Input 2
GP22
General purpose I/O port 2 bit 2
9
Input 1
GP21
General purpose I/O port 2 bit 1
10
Input 0
GP20
General purpose I/O port 2 bit 0
Page 156
KINO-9452 Mini-ITX SBC
B.3 Assembly Language Samples
B.3.1 Enable the DIO Input Function
The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable
digital I/O input functions is listed below.
MOV
AX, 6F08H
Sets the digital port as input
INT
15H
Initiates the INT 15H BIOS call
B.3.2 Enable the DIO Output Function
The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable
digital I/O output functions is listed below.
MOV
AX, 6F09H
MOV
BL, 09H
INT
15H
Sets the digital port as output
Initiates the INT 15H BIOS call
Page 157
KINO-9452 Mini-ITX SBC
Appendix
C
C Watchdog Timer
Page 158
KINO-9452 Mini-ITX SBC
NOTE:
The following discussion applies to DOS environment.
IEI support is
contacted or the IEI website visited for specific drivers for more
sophisticated operating systems, e.g., Windows and Linux.
The Watchdog Timer is provided to ensure that standalone systems can always recover
from catastrophic conditions that cause the CPU to crash. This condition may have
occurred by external EMI or a software bug. When the CPU stops working correctly,
Watchdog Timer either performs a hardware reset (cold boot) or a Non-Maskable Interrupt
(NMI) to bring the system back to a known state.
A BIOS function call (INT 15H) is used to control the Watchdog Timer:
INT 15H:
AH – 6FH Sub-function:
AL – 2:
Sets the Watchdog Timer’s period.
BL:
Time-out value (Its unit-second is dependent on the item “Watchdog
Timer unit select” in CMOS setup).
Table C-1: AH-6FH Sub-function
Call sub-function 2 to set the time-out period of Watchdog Timer first. If the time-out value
is not zero, the Watchdog Timer starts counting down. While the timer value reaches zero,
the system resets. To ensure that this reset condition does not occur, calling sub-function
2 must periodically refresh the Watchdog Timer. However, the Watchdog timer is disabled
if the time-out value is set to zero.
A tolerance of at least 10% must be maintained to avoid unknown routines within the
operating system (DOS), such as disk I/O that can be very time-consuming.
Page 159
KINO-9452 Mini-ITX SBC
NOTE:
When exiting a program it is necessary to disable the Watchdog Timer,
otherwise the system resets.
Example program:
; INITIAL TIMER PERIOD COUNTER
;
W_LOOP:
MOV
AX, 6F02H
;setting the time-out value
MOV
BL, 30
;time-out value is 48 seconds
INT
15H
;
; ADD THE APPLICATION PROGRAM HERE
;
CMP
EXIT_AP, 1
JNE
W_LOOP
;No, restart the application
MOV
AX, 6F02H
;disable Watchdog Timer
MOV
BL, 0
;
INT
15H
;
; EXIT ;
Page 160
;is the application over?
KINO-9452 Mini-ITX SBC
Appendix
D
D Address Mapping
Page 161
KINO-9452 Mini-ITX SBC
D.1 IO Address Map
I/O address
Description
Range
000-01F
DMA Controller
020-021
Interrupt Controller
040-043
System time
060-06F
Keyboard Controller
070-07F
System CMOS/Real time Clock
080-09F
DMA Controller
0A0-0A1
Interrupt Controller
0C0-0DF
DMA Controller
0F0-0FF
Numeric data processor
1F0-1F7
Primary IDE Channel
2E8-2EF
Serial Port 4 (COM4)
2F8-2FF
Serial Port 2 (COM2)
378-37F
Parallel Printer Port 1 (LPT1)
3B0-3BB
Intel 945GME Graphics Controller
3C0-3DF
Intel 945GME Graphics Controller
3E8-3EF
Serial Port 3 (COM3)
3F6-3F6
Primary IDE Channel
3F7-3F7
Standard floppy disk controller
3F8-3FF
Serial Port 1 (COM1)
Table D-1: IO Address Map
D.2 1st MB Memory Address Map
Memory address
Description
00000-9FFFF
System memory
A0000-BFFFF
VGA buffer
F0000-FFFFF
System BIOS
1000000-
Extend BIOS
Table D-2: 1st MB Memory Address Map
Page 162
KINO-9452 Mini-ITX SBC
D.3 IRQ Mapping Table
IRQ
Description
IRQ
Description
IRQ0
System Timer
IRQ8
RTC clock
IRQ1
Keyboard
IRQ9
ACPI
IRQ2
Available
IRQ10
COM 4
IRQ3
COM2
IRQ11
COM 3
IRQ4
COM1
IRQ12
PS/2 mouse
IRQ5
SMBus Controller
IRQ13
FPU
IRQ6
FDC
IRQ14
Primary IDE
IRQ7
Parallel port
IRQ15
Secondary IDE
Table D-3: IRQ Mapping Table
D.4 DMA Channel Assignments
Channel
Function
0
Available
1
Available
2
Floppy disk (8-bit transfer)
3
Available
4
Cascade for DMA controller 1
5
Available
6
Available
7
Available
Table D-4: DMA Channel Assignments
Page 163
KINO-9452 Mini-ITX SBC
Appendix
E
E Compatibility
Page 164
KINO-9452 Mini-ITX SBC
NOTE:
The compatible items described here have been tested by the IEI R&D
team and found to be compatible with the KINO-9452.
E.1 Compatible Processors
The following Socket 478 processors have been successfully tested on the KINO-9452.
CPU
Model Number
Frequency
FSB
Intel® Core™ Duo
T2600
2.16 GHz
667 MHz
Intel® Core™ Duo
T2500
2.0 GHz
667 MHz
Intel® Core™ Duo
T2450
2.0 GHz
533 MHz
Intel® Core™ Duo
T2400
1.83 GHz
667 MHz
Intel® Core™ Duo
T2300
1.66 GHz
667 MHz
Intel® Core™ Duo
T2250
1.73 GHz
533 MHz
Intel® Core™2 Duo
T7600
2.33 GHz
667 MHz
Intel® Core™2 Duo
T7400
2.16 GHz
667 MHz
Intel® Core™2 Duo
T7200
2.0 GHz
667 MHz
Intel® Core™2 Duo
T5600
1.83 GHz
667 MHz
Intel® Core™2 Duo
T5500
1.66 GHz
667 MHz
Intel® Core™ Solo
T1300
1.66 GHz
667 MHz
Intel® Celeron® M
410
1.46 GHz
533 MHz
Intel® Celeron® M
420
1.60 GHz
533 MHz
Page 165
KINO-9452 Mini-ITX SBC
E.2 Compatible Memory Modules
NOTE:
The memory modules listed below have been tested on the KINO-9452
other memory modules that comply with the specifications may also
work on the KINO-9452 but have not been tested.
The following memory modules have been successfully tested on the KINO-9452.
Manufacturer
Model No.
Capacity
Speed
CORSAIR
VS51MB667D2
512 MB
667 MHz
CORSAIR
VS1GB667D2
1 GB
667 MHz
CORSAIR
VS2GB667D2
2 GB
667 MHz
CORSAIR
CM2X1024-6400C4 G
1 GB
800 MHz
Kingston
KHX5400D2K2/2G
1 GB
667 MHz
Kingston
KHX5400D2K2/1G
512 MB
667 MHz
Kingston
KVR667D2N5/2G
2G
667 MHz
A-DATA
M2OEL5G3I4170C1C0z667(5)1GX16
1 GB
667 MHz
A-DATA
M2OAD6H3J4171Q1E52
2 GB
800 MHz
UNIGEN
UG64T6400L8DU-6AL
512 MB
667 MHz
Transcend
TS128MLQ64V8J DDR2-800
1 GB
800 MHz
Transcend
TS256MLQ64V6U DDR2-667
2 GB
667 MHz
Transcend
TS256MLQ64V8U DDR2-800
2 GB
800 MHz
Transcend
TS64MLQ64V6J
512 MB
667 MHz
Transcend
TS64MLQ64V8J
512 MB
800 MHz
UMAX
D48002GP0-73BCt
2 GB
800 MHz
KINGMAX
KLCD48F-A8EB5
1 GB
667 MHz
Page 166
KINO-9452 Mini-ITX SBC
Appendix
F
F Hazardous Materials
Disclosure
Page 167
KINO-9452 Mini-ITX SBC
F.1 Hazardous Material Disclosure Table for IPB Products Cer
tified as RoHS Compliant Under 2002/95/EC Without Mercury
The details provided in this appendix are to ensure that the product is compliant with the
Peoples Republic of China (China) RoHS standards. The table below acknowledges the
presences of small quantities of certain materials in the product, and is applicable to China
RoHS only.
A label will be placed on each product to indicate the estimated “Environmentally Friendly
Use Period” (EFUP). This is an estimate of the number of years that these substances
would “not leak out or undergo abrupt change.” This product may contain replaceable
sub-assemblies/components which have a shorter EFUP such as batteries and lamps.
These components will be separately marked.
Please refer to the table on the next page.
Page 168
KINO-9452 Mini-ITX SBC
Part Name
Toxic or Hazardous Substances and Elements
Lead
Mercury
Cadmium
Hexavalent
Polybrominated
Polybrominated
(Pb)
(Hg)
(Cd)
Chromium
Biphenyls
Diphenyl Ethers
(CR(VI))
(PBB)
(PBDE)
Housing
X
O
O
O
O
X
Display
X
O
O
O
O
X
Printed Circuit
X
O
O
O
O
X
Metal Fasteners
X
O
O
O
O
O
Cable Assembly
X
O
O
O
O
X
Fan Assembly
X
O
O
O
O
X
Power Supply
X
O
O
O
O
X
O
O
O
O
O
Board
Assemblies
Battery
O
O: This toxic or hazardous substance is contained in all of the homogeneous materials for the part is below
the limit requirement in SJ/T11363-2006
X: This toxic or hazardous substance is contained in at least one of the homogeneous materials for this part
is above the limit requirement in SJ/T11363-2006
Page 169
KINO-9452 Mini-ITX SBC
此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符
合中国 RoHS 标准规定的限量要求。
本产品上会附有”环境友好使用期限”的标签,此期限是估算这些物质”不会有泄漏或突变”的
年限。本产品可能包含有较短的环境友好使用期限的可替换元件,像是电池或灯管,这些
元件将会单独标示出来。
部件名称
有毒有害物质或元素
铅
汞
镉
六价铬
多溴联苯
多溴二苯醚
(Pb)
(Hg)
(Cd)
(CR(VI))
(PBB)
(PBDE)
壳体
X
O
O
O
O
X
显示
X
O
O
O
O
X
印刷电路板
X
O
O
O
O
X
金属螺帽
X
O
O
O
O
O
电缆组装
X
O
O
O
O
X
风扇组装
X
O
O
O
O
X
电力供应组装
X
O
O
O
O
X
电池
O
O
O
O
O
O
O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
Page 170
KINO-9452 Mini-ITX SBC
Appendix
G
G External AC’97 Audio
CODEC
Page 171
KINO-9452 Mini-ITX SBC
G.1 Introduction
The motherboard comes with an onboard Realtek ALC883 CODEC. The ALC883 is a
16-bit, full-duplex AC'97 Rev. 2.3 compatible six-channel audio CODEC that provides
three pairs of stereo outputs with 5-bit volume control, a mono output, and multiple stereo
and mono inputs, along with flexible mixing, gain, and mute functions.
G.1.1 Accessing the AC’97 CODEC
The CODEC is accessed through the phone jacks on the rear panel of the motherboard.
The phone jacks include:
LINE IN
LINE OUT
MIC IN
G.1.2 Driver Installation
The driver installation has been described in Section 7.5.
After rebooting, the sound effect configuration utility appears in the Windows Control
Panel (Figure G-1). If the peripheral speakers are properly connected, sound effects
should be heard.
Page 172
KINO-9452 Mini-ITX SBC
Figure G-1: Control Panel Sound Effect Manager
G.2 Sound Effect Configuration
G.2.1 Accessing the Sound Effects Manager
Follow the steps below to access the Sound Effect Manager.
Step 1: Install the ALC883 audio CODEC driver (see Section 7.5).
Step 2: Click the Sound Effect Manager icon in the system task bar (Figure G-2).
Figure G-2: Sound Effect Manager Icon [Task Bar]
Step 3: The sound effect manager appears (Figure G-3).
Page 173
KINO-9452 Mini-ITX SBC
Figure G-3: Sound Effects Manager (ALC883)
NOTE:
The Sound Effect Manager shown in Figure G-3 is for the RealTek ALC883
audio CODEC. Different CODECs may have different sound manager
appearances.
The following section describes the different configuration options in the Sound Effect
Manager.
G.2.2 Sound Effect Manager Configuration Options
The Sound Effects Manager enables configuration of the items listed below. To configure
these items click the corresponding menu tab in the Sound Effects Manager
(Figure G-3).
Page 174
KINO-9452 Mini-ITX SBC
NOTE:
The Karaoke Mode is configured in the Sound Effect menu. To access Karaoke
configuration settings, click on the Sound Effect menu tab.
Sound Effect
Karaoke Mode
Equalizer
Speaker Configuration
Speaker Test
S/PDIF-In
S/PDIF-Out
Connector Sensing
HRTF Demo
Microphone Effect
General
NOTE:
Not all RealTek Sound Effect Managers have all the above listed options. The
Sound Effect Manager loaded onto the system may only have some of the
options listed above.
Below is a brief description of the available configuration options in the Sound Effects
Manager.
Sound Effect - Select a sound effect from the 23 listed options in the drop
down menu. Selected sound effect properties can be edited. Click EDIT to edit
the sound effect.
Karaoke Mode - Karaoke Mode is accessed in the Sound Effect tab. The
Voice Cancellation disables the vocal part of the music being played. The
Page 175
KINO-9452 Mini-ITX SBC
Key adjustment up or down arrow icons enable users to define a key that fits
a certain vocal range.
Equalizer Selection - Preset equalizer settings enable easy audio range
settings. Ten frequency bands can be configured.
Speaker Configuration - Multi-channel speaker settings are configured in
this menu. Configurable options include:
o
o
o
o
o
Headphone
Channel mode for stereo speaker output
Channel mode for 4 speaker output
Channel mode for 5.1 speaker output
Synchronize the phonejack switch with speakers settings
Speaker Test - Each speaker connected to the system is tested individually
to see if the 4-channel or 6-channel audio operates properly.
S/PDIF-In & S/PDIF-Out - S/PDIF is used to transmit digital and analog audio
signals with either a 48 or 44.1kHz sample rate.
HRTF Demo - Adjust HRTF (Head Related Transfer Functions) 3D positional
audio before running 3D applications.
Microphone Effect - Microphone noise suppression is enabled in this menu.
General - General information about the installed AC’97 audio configuration
utility is listed here.
Page 176
KINO-9452 Mini-ITX SBC
H Index
Page 177
KINO-9452 Mini-ITX SBC
CD-ROM ....................................... 52, 97, 99
3
3D graphic ...................................................3
A
Center/Subwoofer port............................52
chassis .......................................... 36, 51, 76
installation..............................................76
chipset........................................................12
northbridge ............................................12
AC’97 Audio CODEC ...............................170
Clear CMOS.......................................... 5, 69
Advanced Power Management ...............126
clear CMOS jumper ...................................71
airflow ........................................................76
location ..................................................71
ALC883................................6, 130, 142, 171
settings ..................................................71
AMI BIOS.........................................7, 89, 91
CMOS ........................................................71
anti-static precautions..........................28, 60
clear CMOS jumper ...............................71
anti-static pad ..................................28, 60
COM 3
anti-static wristband.........................28, 60
COM 3 function select ...........................72
handling ...........................................28, 60
COM 3 function select jumper ...................72
self-grounding..................................28, 60
location ..................................................73
ASF2.0.........................................................7
settings ..................................................72
AT/ATX power select jumper .....................69
connectors, external
location ..................................................70
audio jacks.............................................52
settings ..................................................70
COM 1 serial port ..................................56
ATX power .............................................7, 45
CRT connector.......................................53
audio
LAN connector.......................................54
installation..............................................82
RJ-45 connector ....................................54
audio jacks.................................................52
TV connector .........................................57
Audio jacks ............................................5, 51
USB port ................................................58
connectors, pinouts and location
B
BIOS ..........................................................22
BIOS chipset..............................................22
C
10-pin serial port....................................47
14-pin serial port....................................46
audio......................................................36
digital input/output .................................39
fan..........................................................37
front panel..............................................38
cables ........................................................77
IDE.........................................................40
dual RS-232 cable.................................79
internal USB ..........................................50
Page 178
KINO-9452 Mini-ITX SBC
LCD backlight ........................................41
DMA controller ........................................ 162
LVDS LCD .............................................42
Dual-core .....................................................3
mini PCI .................................................44
DVD player.................................................52
power.....................................................45
SATA......................................................48
SPDIF ....................................................49
cooling .......................................................76
airflow ....................................................76
cooling fan ...........................................65, 67
cooling kit installation.................................65
Core™ Duo .................................................6
Core™ Solo.................................................6
E
electrostatic discharge ........................ 28, 60
Enhanced Hardware Monitor .....................23
Ethernet .....................................................81
RJ-45 cable connector ..........................81
external peripheral interface ......................81
connection .............................................81
connectors .............................................81
CPU
cooling fan .............................................65
heat sink ................................................65
installation..............................................63
External Peripheral Interface Connectors
Keyboard/Mouse ...................................55
F
CPU ........................................................... 11
compatible ............................................. 11
fan speed controller ...................................23
CRT connector...........................................53
front panel ........................................... 36, 38
CRT monitor...............................................83
Front panel............................................ 4, 34
front side bus ...............................................2
D
H
DB-15 connector..................................83, 84
DB-9.....................................................35, 56
HDTV .......................................................3, 6
DDR2 .............................................3, 4, 6, 34
heat sink.....................................................65
Digital I/O .................................................4, 6
High Definition Audio .............................. 126
dimensions...................................................9
board .......................................................9
external peripheral interface connector
panel ...................................................9
DIMM .........................................................67
installation..............................................67
specifcations..........................................67
DIO Interface ...................................154, 160
Page 2
I
ICH7-M.........................................................6
IDE device..................................................78
connector...............................................78
IDE flat cable .........................................78
IDE flat cable..............................................78
IDE interface ..............................................18
KINO-9452 Mini-ITX SBC
installation checklist ...................................62
settings ..................................................75
Intel 945GM .........................................6, 161
M
Intel® GME965 ..........................................12
J
memory module ...........................................6
memory module installation .......................67
jumper........................................................69
memory support .........................................13
AT/ATX power select .............................69
Mini PCI ................................ 5, 6, 34, 44, 45
clear CMOS...........................................71
motherboard...............................................77
COM 3 function select ...........................72
installation..............................................77
jumper configuration..............................69
mouse ........................................................81
LVDS resolution selection .....................73
multi media application ................................3
LVDS voltage selection .........................75
N
K
Northbridge ..................................... 6, 34, 37
keyboard ..............................................81, 85
northbridge chipset ....................................12
keyboard controller ....................................24
P
L
PCI3, 5, 6, 34, 44, 45, 90, 108, 109, 113, 114
L1 cache ................................................3, 94
PCI Express GbE controller.......................21
L2 cache ................................................3, 94
PCI interface ..............................................19
LAN connector ...........................................54
PCIe bus ....................................................21
LCD backlight ..................................4, 34, 41
peripheral device cables ............................77
LCD voltage ...........................................5, 69
Power Button Mode ................................ 107
LPC bus .....................................................22
power supply
LPC interface .......................................19, 23
AT/ATX power select jumper .................69
LVDS display .......................................73, 75
processors .................................................11
resolution select ....................................73
PS/2 ............................................ 55, 56, 162
voltage select ........................................75
PS/2 connector ..........................................85
LVDS resolution selection jumper..............73
location ..................................................74
PS/2 keyboard
connection .............................................85
settings ..................................................74
LVDS voltage selection jumper..................75
location ..................................................75
R
real time clock ............................................20
Page 3
KINO-9452 Mini-ITX SBC
RJ-45 .......................................35, 51, 54, 55
SPDIF ....................................... 5, 35, 49, 50
RJ-45 connector ........................................54
Super I/O chipset .......................................22
RJ-45 connector ........................................82
SuperIO......................................................92
RJ-45 Ethernet
S-video
connection .............................................82
S-video cable connection ......................86
RJ-45 Ethernet...........................................82
S-video.......................................................86
RoHS ...........................................................3
S-video cable connection...........................86
rotation signal ............................................37
RS-232.......................................................79
cable connection ...................................79
dual cable ..............................................79
S
SATA ..........................................2, 3, 5, 6, 48
controller................................................20
SATA drive .................................................80
cables ....................................................80
connection .............................................80
power cable ...........................................80
Serial Device
connection .............................................84
Serial Device..............................................84
T
TV connector..............................................57
TV-Out................................. 5, 35, 51, 57, 58
U
unpacking...................................................28
unpacking checklist ...............................29
unpacking precautions...........................28
USB..............................................................2
controller................................................20
USB 2.0......................3, 5, 6, 35, 51, 52, 112
USB port ....................................................58
V
serial port ...................................................56
serial ports .................................................23
VGA ...........................................................83
Side Speaker Out port ...............................52
VGA monitor...............................................83
socket 479 CPU
connection .............................................83
cooling kit ..............................................65
cooling kit installation ............................65
installation..............................................63
Sound Effect Configuration......................172
Sound Effects Manager ...........................172
Page 4
W
warranty validation .....................................62
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement