- Industrial & lab equipment
- Electrical equipment & supplies
- Power conditioning
- Electrical relays
- VERIS INDUSTRIES, INC.
- V100DC
- Installation Guide
advertisement
TM
V100DC
RELAYS
INSTALLATION GUIDE
V100DC
10A SPDT Enclosed Relay
10-30 VDC Coil
Installer’s Specifications
Operating Temperature -34°C to 60°C (-29° to 140°F)
Operating Humidity
Expected Relay Life
10-90% non condensing
Electrical (at rated current): 100,000 cycles
Mechanical
LED ON=energized Relay Status
Wire Specifications:
Lead Length
Gauge
Insulation Class
Agency Approvals
14” (356mm) min.
UL1015; Coil: 18 AWG; Contacts: 16 AWG
600 VAC RMS
UL508 enclosed device listing
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.
• This equipment must only be installed and serviced by qualified electrical personnel.
• Read, understand and follow the instructions before installing this product.
• Turn off all power supplying equipment before working on or inside the equipment.
• Use a properly rated voltage sensing device to confirm power is off.
DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION
Failure to follow these instructions will result in death or serious injury.
NOTICE
• This product is not intended for life or safety applications.
• Do not install this product in hazardous or classified locations.
• The installer is responsible for conformance to all applicable codes.
• Mount this product inside a suitable fire and electrical enclosure.
DIMENSIONS
2.9"
(74 mm)
INSTALLATION
Disconnect and lock out all power sources before beginning the installation.
1. Using the threaded nipple, connect the relay to the desired enclosure through a knock out hole.
2. Secure with the conduit nut provided.
3. Connect Coil:
• Choose the coil common lead (white with yellow stripe) and connect it to the (-) source termination point.
• Choose the low voltage (10-30 VAC/DC, white with blue stripe) lead, and connect it to the (+) source termination point.*
4. Connect Relay Contacts:
• Choose the relay common wire (yellow) and connect to switched load.
• Choose the relay N.O. (orange) and/or* N.C. (blue) lead and connect to switched load.
5. Secure the enclosure and reconnect power.
* Isolate or insulate all non-terminated wires according to local electrical code requirements, i.e. wire nut.
2.8"
(71 mm)
1.6"
(41 mm)
1.7"
(43 mm)
1/2" NPT Nipple
1.8"
(46 mm)
Z203521-0B PAGE 1 ©2012 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 03121
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
TM
WIRING COLOR CODES
CONTROL SYSTEM INPUT
LOW wht/blue blue
White
10-30VDC blue
COMM wht/yellow yello w White
Common yello w
CONTACT AND COIL SPECIFICATIONS
TYPICAL COIL PERFORMANCE
Pull in Voltage DC
10-30V..................................... 9
Drop Out Voltage DC
10-30V..................................... 3
Voltage Coil Current
DC
10V.......................................... 14mA
12V.......................................... 14mA
24V.......................................... 16mA
30V.......................................... 18mA
CONTACT RATINGS
Resistive.............. 10A@277VAC, 28VDC
Motor.................... 120VAC, 1/3HP N.O. & 1/6HP N.C.
240VAC, 1/3HP N.O. & 1/6HP N.C.
277VAC, 1/4HP N.O. & 1/8HP N.C.
Pilot Duty............. 277VAC, (1.7A), 480VA N.O.
Ballast.................. 277VAC, 1.7A
Tungsten............... 120VAC, TV3 N.O. TV2 N.C.
Gold Flash............. Yes
CONTACT OUTPUT
N.C.
V100DC
INSTALLATION GUIDE
WIRING EXAMPLE
Nipple mount directly to a panel
To Load CONT
ACTS
YELLOW
Common
COIL
To Controls
ORANGE
N.O.
Nipple mount to any 2x or 4x electrical box
To Load CONTACTS
CO
IL
Wire
Nut
To Controls
Z203521-0B PAGE 2 ©2012 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 03121
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project