Motorola | SURFBOARD CABLE MODEM SB4100 - annexe 1 | User guide | Motorola SURFBOARD CABLE MODEM SB4100 - annexe 1 User guide

Motorola SURFBOARD CABLE MODEM SB4100 - annexe 1 User guide
SB4200 User Guide
High-Speed Access to the Internet
R
SURFboard
Cable Modem
Declaration of Conformity
We,
Motorola, Inc.
Broadband Communications Sector
6450 Sequence Drive
San Diego, CA, U.S.A.
declare under our sole responsibility that the
SURFboard Cable Modem
Model SB4200i
to which the declaration relates is in conformity with the following standards:
EN55022
EN55024
EN60950
CISPR 22
CISPR 24
IEC950 : 1991 + A1 : 1992 + A2 : 1993 +
A3 : 1995 + A4 : 1996
following the provisions of the Directive(s) of the Council of the European Union:
EMC Directive 89/336/EEC
Low Voltage Directive 73/23/EEC
Caution
This product was qualified under test conditions that included the use of the supplied cable between system
components. To be in compliance with regulations, the user must use this cable and install it properly.
Use only an ac line cord that complies with the country’s product safety requirements.
To ensure regulatory and safety compliance, use only the provided Ethernet, USB, and power cables.
Copyright © 2001 by Motorola, Inc. All rights reserved. No part of the contents of this book may be reproduced or transmitted in any
form or by any means without written permission of the publisher.
Motorola and the stylized M logo are registered trademarks of Motorola, Inc. All other product or service marks are the property of
their respective owners.
Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part
of Motorola to provide notification of such revision or change. Motorola provides this guide without warranty of any kind, either implied
or expressed, including, but not limited, to the implied warranties of merchantability and fitness for a particular purpose. Motorola may
make improvements or changes in the product(s) described in this manual at any time.
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Top and Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installation and Configuration Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Cabling and Startup for a Single User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting Up a USB Driver in Windows 98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Setting Up a USB Driver in Windows 2000 and Me . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Configuring for TCP/IP in Windows 95, 98, and Me . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Configuring for TCP/IP in Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Verifying Your IP Address in Windows 95, 98, and Me . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Verifying Your IP Address in Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Cabling for Multiple Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
i
Table of Contents (cont’d)
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Problems and Possible Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Removing the SB4200 Device Listing from Windows 98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Removing the USB Driver from Windows 98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Removing the SB4200 Device Listing from Windows 2000 and Windows Me . . . . . . . . . . . . . . . . . . 42
Removing the USB Driver from Windows 2000 and Windows Me . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Recovery after Installation Errors with Win98_SE and Windows 98 . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Contact Us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
FAQs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Software License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
ii
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Easier!*
Just open your browser and surf!
Always on, always connected
Congratulations, you have a new state-of-the-art SB4200 cable modem! This
high-speed, upgradeable modem enables you to connect your home or business
computer to a DOCSIS-compliant data network. The SB4200 transmits and receives
data at much higher speeds than traditional telephone or ISDN modems.
Faster!**
Up to 100 times faster than a phone modem
Better!***
It provides high-speed access to the Internet and other online services.
A Universal Serial Bus (USB) port is available for a single-user direct connection to
USB-equipped computers. The standard Ethernet connection provides network service
to single or multiple users.
A great choice for Internet access
Unlike a telephone modem, the SB4200 is always online. Just open your browser and
surf.
* Unlike analog phone modems and ISDN, you’re always on, always connected.
** Actual speed will vary. Many network and other factors affect download speeds.
*** SURFboard is made by the company with over 50 years of cable TV expertise.
Home
Print
X
Exit
1
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Top and Front Panel
The standby button suspends your Internet service. The six front-panel lights provide
information about power, communications, and errors.
1
2
3
4
5
6
7
Item
Description
1
Standby
Switch
2
Power
LED
Receive
LED
Press this switch to disable the Ethernet and USB ports on the
SB4200. No data is transmitted or received. Press this switch again
to transmit and receive data. The Standby button offers added
Internet security. When the standby switch is activated, all other
lights turn off.
When the light is flashing, startup diagnostics are being performed.
A solid light indicates the SB4200 is powered on.
When the light is flashing, the SB4200 is scanning for a receive
channel connection. A solid light indicates the channel connection
is acquired.
When the light is flashing, the SB4200 is scanning for the send
channel connection. A solid light indicates the channel connection
is acquired.
3
4
Home
Print
X
Exit
Send
LED
2
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Top and Front Panel
Item
Description
5
Online
LED
6
Activity
7
Standby
When the light is flashing, the SB4200 is scanning for the network
configuration server connection. A solid light indicates the network
connection is acquired.
When the light is flashing, the SB4200 is transmitting or receiving
data. When the light is off, the SB4200 is not transmitting or
receiving data.
After pressing the Standby button on the top of the SB4200, the
Standby light turns on indicating the Ethernet and USB ports are
disabled (not receiving or transmitting data). Internet service is
interrupted until the Standby button is pressed again. The Standby
button offers added Internet security.
1
2
3
4
5
6
7
Home
Print
X
Exit
3
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Rear Panel
The rear panel provides cabling connectors, status lights, and the power receptacle.
1
Item
Description
LINK/ACT
When the light is on, the Ethernet connection is available. A blinking
light indicates data is being transferred.
This port is the Ethernet connector that transfers data to and from
your computer.
2
1
2
3
4
5
3
100
6
4
5
USB
•
The light is on when a 100Base-T link is established and off when a
10Base-T link is established.
This port provides a direct connection to USB equipped computers.
This is the recessed reset button.
6
7
CABLE
POWER
This port transfers data to and from the service provider.
This connector provides power to the SB4200.
7
Home
Print
X
Exit
4
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Before You Begin
Before you begin the installation, check that you have:
Power cord
10/100Base-T
shielded
Ethernet cable
USB cable
SB4200
User Guide
CD-ROM
Home
Item
Description
Power cord
Required for connecting the SB4200 to the AC
electrical outlet.
One 10/100Base-T
shielded Ethernet cable
Required for connecting to the Ethernet port.
One USB cable
Required for connecting to the USB port.
SB4200 User Guide
CD-ROM
Contains the User Guide and USB drivers necessary
for connecting to USB port.
You need to purchase a 75-ohm coaxial cable with F-type connectors for connecting
your SB4200 to the nearest cable outlet. If you have a TV attached to the cable outlet,
you may need a 5-900 MHz splitter to use both the TV and the SB4200. Both the coaxial
cable and the RF splitter are readily available at consumer electronic stores.
Print
X
Exit
5
Introduction
Before You Begin
You must call your service provider to activate
your service. You need to provide the media
access control (MAC) address. This address is
found on the SB4200 bar code label marked
HFC MAC ID on the rear panel. The address
format is 00:20:40:xx:xx:xx or
00:04:db:xx:xx:xx.
Home
Print
X
Exit
Installation
Configuration
Troubleshooting
Legal
Precautions
!
Postpone SB4200 installation until there is no risk of thunderstorm or lightning
activity in the area. Avoid damaging the SB4200 with static by touching the coaxial
cable connector when it is attached to the earth grounded coaxial cable TV wall
outlet. Always first touch the coaxial cable connector on the SB4200 when you are
disconnecting or re-connecting your USB or Ethernet cable from the SB4200 or your
PC.
!
Do not block the ventilation holes on the sides of the cable modem to prevent
overheating the SB4200.
!
Do not open the SB4200 cable modem. Refer all service to your local service
provider.
!
Wipe the modem with a clean, dry cloth. Never use cleaning fluid or similar
chemicals. Do not spray cleaners directly on the unit or use forced air to remove
dust.
6
Introduction
Before You Begin
System Requirements Summary
!
Service Provider
!
Computer
!
HTML Browser
!
Ethernet card or SB4200 CD-ROM
containing the USB software
Installation
Configuration
Troubleshooting
Legal
System Requirements
You need the following to use the SB4200 with your computer system:
Service Provider
You must sign up with a data service provider for access to the Internet and other online
services. You should ask your data service provider the following questions:
!
Do you have any special system requirements?
!
When can I begin to use my cable modem?
!
Are there any files I need to download once I’m connected?
!
Do I need a user name or password to access the Internet or use Email?
Computer
Your computer must be equipped with a USB or Ethernet port and the Transmission
Control Protocol/Internet Protocol (TCP/IP) to access the SB4200. The SB4200 is
compatible with Microsoft®, Macintosh® and UNIX® operating systems. Computers using
Windows® 95, UNIX, or Macintosh systems must use the Ethernet connection.
Home
Print
X
Exit
7
Introduction
Before You Begin
The Ethernet card must be installed before the
SB4200. If it isn't, follow the installation
instructions that came with your Ethernet
card.
Installation
Configuration
Troubleshooting
Legal
System Requirements
HTML Browser
Any standard HTML (web) browser works with the SB4200.
Ethernet Card or SB4200 CD-ROM Containing the USB
Software
Any standard 10/100Base-T Ethernet card operates with the SB4200. This is not needed
if connecting to the USB port. The Ethernet card must be installed before the SB4200. If
it is not, follow the installation instructions included with your Ethernet card.
The USB connection is supported by Windows 98, Windows 2000, and Windows Me and
requires special software to operate. The USB driver software files are on the CD-ROM
supplied with your SB4200.
The USB drivers can be upgraded from the Internet. Check our website for information,
http://www.motorola.com/broadband.
Your computer must be configured for TCP/IP and have an IP address for the SB4200 to
operate. Your service provider furnishes the IP address.
Home
Print
X
Exit
8
Introduction
Before You Begin
Avoid damaging the SB4200
or your PC with static electricity.
Installation
Configuration
Installation
Installation and Configuration Tasks
!
Install cables
!
Set up USB in Windows if you are using a USB port on your PC
!
Configure TCP/IP
!
Verify IP address
There are two sections for USB installation:
!
Windows 98
!
Windows 2000 and Windows Me
To release any static charges, touch
the coaxial cable connector on the modem
before connecting or disconnecting
the USB or Ethernet cables.
Home
Print
X
Exit
Troubleshooting
9
Legal
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Cabling and Startup for a Single User
You must allow 5 to 30 minutes to power up the first time because the SB4200 must find
and lock on the appropriate channels for communications.
Ethernet
OUT
USB
To Ethernet
or USB
To cable
outlet
1
Be sure that your computer is on and the SB4200 is unplugged.
2
Connect the coaxial TV cable to the cable outlet or splitter and the other end to the
SB4200 connector marked CABLE. Hand-tighten the connectors to avoid damaging
them. You may need a 5-900 MHz splitter and an additional 75-ohm coaxial cable if
you have a TV connected to the cable outlet.
3
Insert the SB4200 CD-ROM into your CD-ROM drive.
4
Plug the power cord into the SB4200 connector marked POWER and the other end
to the electrical outlet.
Caution
Do not connect both Ethernet and USB cables to the same
computer.
To electrical
outlet
Home
Print
X
Exit
10
Introduction
Before You Begin
To turn on your SB4200, simply plug it in. It is
not necessary to unplug it when not in use.
Installation
Home
Print
Troubleshooting
Legal
Cabling and Startup for a Single User
5
X
Exit
Configuration
Check that the lights on the front of the SB4200 cycle through the following
sequence:
!
Power flashes during a self-test. When the self-test is successfully complete, the
light is solid green.
!
Receive flashes while the SB4200 scans for the receive channel. When the
receive channel is locked, the light is solid green.
!
Send flashes while the SB4200 scans for the send channel. When the send
channel is locked, the light is solid green.
!
Online flashes while the SB4200 is obtaining configuration information. When
the configuration information is obtained, the light is solid green.
11
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Cabling and Startup for a Single User
6
Connect your computer to the SB4200 using one of the following methods:
USB
Ensure the SB4200 CD-ROM is inserted into your CD-ROM drive. The CD-ROM
must be in the drive before plugging in the USB cable.
Connect the USB cable to the SB4200 port marked USB and the other end to the
USB port on the back of your computer.
For Windows 98 USB users, go to the next page.
For Windows 2000 and Windows Me USB users, go to page 18.
Ethernet
Connect the 10/100Base-T shielded Ethernet cable to the SB4200 Ethernet
connector and the other end to the Ethernet jack on the back of your computer. For
an Ethernet connection, skip over the USB instructions and go to
“Configuring for TCP/IP.”
During normal operation, the Power, Receive, Send, and Online lights are on and
the Activity light flashes when transferring data between the SB4200 and your
computer.
Home
Print
X
Exit
12
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Setting Up a USB Driver in Windows 98
After plugging in the USB connector, the window on the left is displayed.
Ensure the SB4200 CD-ROM is inserted into your CD-ROM drive. The CD-ROM must
be in the drive before plugging in the USB cable.
1
Home
Print
X
Exit
Click Next.
13
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Setting Up a USB Driver in Windows 98
2
Be sure the text that reads “Search for the best driver for your device” is selected as
displayed in the upper window on the left. Then, click Next, and the lower window
on the left is displayed showing a location.
If your computer successfully locates the driver, proceed to step 4.
Home
Print
X
Exit
14
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Setting Up a USB Driver in Windows 98
If your computer does not locate the driver, the previous window is displayed again.
You should select Specify a location and type in the location of your CD-ROM
drive as shown in the upper window.
3
Click Next.
Note: If the window on the lower left of this page is not displayed, verify that the Motorola
CD-ROM is in the drive and accessible. If you still cannot find the correct driver file, then
cancel the installation and remove invalid entries as described in Example 1 and/or
Example 2 found under the heading called “Recovery After Installation Errors with
Win98_SE and Windows 98” starting on page 48.
4
Home
Print
X
Exit
Select The updated driver. . . and then click Next.
15
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Setting Up a USB Driver in Windows 98
Note: If the window on the upper left of this page is not displayed with text stating that the
NET4100.INF file was found, then verify that the Motorola CD-ROM is in the drive and
accessible. If the correct driver file is still not listed, then cancel the installation and
remove invalid entries as described in Example 1 and/or Example 2 found under the
heading called “Recovery After Installation Errors with Win98_SE and Windows 98”
starting on page 48 of this user guide.
5
After the window on the left is displayed, click Next.
Note: In some installations, a window with the message Copying Files... may display
and prompt you to specify your CD-ROM drive. If this window displays, enter your
CD-ROM drive letter (for example, “D:”) and then click OK.
6
At this point, Windows 98 may need additional system files loaded to complete the
installation. These files are located on your Windows 98 CD-ROM.Be sure your
Windows 98 CD-ROM is in the CD-ROM Drive and click OK to install System Files.
The SB4200 uses the same driver as the
SB4100.
Home
Print
X
Exit
16
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Setting Up a USB Driver in Windows 98
7
After all of the necessary Windows 98 files have been loaded, the upper window on
the left is displayed confirming a successful installation.
8
Click Finish and the lower window is displayed.
9
Click Yes to restart your computer.
Refer to “Verifying Your IP Address in Windows 95, 98, and Me” on page 30 to
verify your TCP/IP setup.
If you have any difficulties with the installation process, please follow the instructions for
“Removing the USB Driver from a Windows 98” computer that begin on page 40.
Home
Print
X
Exit
17
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Setting Up a USB Driver in
Windows 2000 and Windows Me
Ensure the SB4200 CD-ROM is inserted into your CD-ROM drive. The CD-ROM must
be in the drive before plugging in the USB cable.
The SB4200 uses the same driver as the
SB4100.
Home
Print
X
Exit
1
After making the USB connection, the Found New Hardware window is displayed.
18
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Setting Up a USB Driver in
Windows 2000 and Windows Me
Home
Print
X
Exit
2
After several seconds, the Hardware Wizard window is displayed.
3
Click Next, and the lower window is displayed.
4
Be sure that the text that reads “Search for a suitable driver for my device” is
selected and click Next.
19
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Setting Up a USB Driver in
Windows 2000 and Windows Me
Home
Print
X
Exit
5
Be sure that the CD-ROM drive’s box is the only one checked as illustrated in the
upper window. Click Next, and the lower window is displayed.
6
Click Next.
20
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Setting Up a USB Driver in
Windows 2000 and Windows Me
Home
Print
X
Exit
7
On the Insert Disk window, D:\ represents the CD-ROM drive. If D:\ is not the
CD-ROM drive on your computer, enter the drive letter for your CD-ROM drive.
8
Click OK and the lower window on the left is displayed.
9
Select Browse and then locate a file called Net4100.sys. This file is located on the
Motorola SB4200 CD-ROM root directory. Double-click the file called Net4100.sys.
21
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Setting Up a USB Driver in
Windows 2000 and Windows Me
10 On the Files Needed window, click OK and the Found New Hardware Wizard
window is displayed.
11 Click Finish to complete the installation.
If you have any difficulties with the installation process, please follow the instructions for
“Removing the USB Driver from a Windows 2000 or Windows Me” computer that begin
on page 46.
Home
Print
X
Exit
22
Introduction
Before You Begin
The SB4200 contains all necessary software.
You don't need to configure the SB4200, but
you must configure your computer for TCP/IP
(software protocol developed for
communication between computers) and
check for an IP address. Your service provider
may provide additional instructions for setting
up your computer.
Home
Print
X
Exit
Installation
Configuration
Troubleshooting
Legal
Configuring for TCP/IP in Windows 95,
98, and Me
The following basic instructions are for Windows 95, 98 and Me. Windows 2000
configuration instructions begin on page 26. If you are using a different operating
system, refer to your user guide.
1
On the Windows Desktop, click Start.
2
Select Settings and then Control Panel from the pop-up menus.
3
Double-click the Network icon on the Control Panel window.
4
Select the Configuration tab on the Network window.
5
Check to see if TCP/IP has been installed for the device being used (Ethernet card
or USB). If TCP/IP is displayed in the list of network components, it is installed and
you can proceed to step 10. If TCP/IP is not displayed on the list, continue with
step 6.
6
Click Add.
23
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Configuring for TCP/IP in Windows 95,
98, and ME
Home
Print
X
Exit
7
Double-click the Protocol option on Select Network Component Type window.
8
Click Microsoft in the Manufacturers section and then click TCP/IP in the Network
Protocol section of Select Network Protocol window.
9
Click OK.
24
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Configuring for TCP/IP in Windows 95,
98, and Me
10 Click TCP/IP on the Network window. If you have more than one TCP/IP entry,
choose the one associated with the Ethernet card or USB device connected to the
SB4200.
11 Click Properties.
12 Select the IP Address tab on the TCP/IP window.
13 Click Obtain an IP address automatically.
14 Click OK to accept the TCP/IP settings.
15 Click OK to close the Network window.
16 Click OK when prompted to restart your computer and then click OK again.
Home
Print
X
Exit
25
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Configuring for TCP/IP in Windows 2000
The following basic instructions are for Windows 2000 users. Windows 95, 98, and Me
instructions begin on page 23. If you are using a different operating system, refer to your
user guide.
Home
Print
X
Exit
1
On the Windows Desktop, click Start.
2
Select Settings and then Control Panel from the pop-up menus.
3
Double-click the Network and Dial-up Connections icon on the Control Panel
window.
4
On the Network and Dial-up Connections window, click Local Area Connection #.
The value of this number (#) varies from system to system, but usually is 2. The
Local Area Connection # Status window is displayed as shown at the top of the next
page.
26
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Configuring for TCP/IP in Windows 2000
Home
Print
X
Exit
5
Click Properties and information similar to that shown in the lower window is
displayed.
6
If Internet Protocol (TCP/IP) is displayed in the list of network components, TCP/IP
is installed and you can proceed to step 10. If TCP/IP is not displayed on the list,
continue with step 7 by clicking Install. This causes the Select Network Component
Type window to be displayed as shown at the top of the next page.
27
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Configuring for TCP/IP in Windows 2000
Home
Print
X
Exit
7
Click Protocol on the Select Network Component Type window and then click Add.
The Select Network Protocol window is displayed similar to the example on the
lower left of this page.
8
Click Internet Protocol (TCP/IP) in the Network Protocol section of Select Network
Protocol window.
9
Click OK and the Local Area Connection # Properties window is re-displayed as
shown at the top of the next page.
28
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Configuring for TCP/IP in Windows 2000
10 On the Local Area Connection # Properties window, make sure a check mark is in
the box next to Internet Protocol (TCP/IP). Click Properties. The Internet Protocol
(TCP/IP) Properties windows is displayed as shown on the lower left of this page.
Make sure that Obtain IP address automatically and Obtain DNS server address
automatically are selected.
11 Click OK to accept the TCP/IP settings.
12 Click OK to close the Local Area Connection # Properties window.
13 Click OK when prompted to restart your computer and then click OK again.
Home
Print
X
Exit
29
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Verifying Your IP Address in
Windows 95, 98, and Me
The following basic instructions are for Windows 95, 98, and Me. The instructions for
verifying your IP address for Windows 2000 are found on the next page. For any other
operating system, please refer to your specific operating system guide for IP address
verification.
To check the IP address:
The values shown for Adapter Address, IP
Address, Subnet Mask, and Default Gateway
on your PC will be different than those shown
in the example above.
If autoconfiguration is displayed before IP
Address in Windows 98, call your service
provider.
Home
Print
X
Exit
1
On the Windows Desktop, click Start.
2
Select Run.
3
Type winipcfg.exe and click OK. A window similar to the example shown on this
page is displayed.
4
Select your adapter name—the Ethernet card or USB device.
5
Click Renew.
6
Click OK after the system displays an IP address.
If after performing this procedure your computer does not access the Internet, call your
service provider. They will assist in your configuration.
30
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Verifying Your IP Address in
Windows 2000
The following basic instructions are for Windows 2000. The instructions for verifying your
IP address for Windows 95, and Me are found on the previous page. For any other
operating system, please refer to your specific operating system guide for IP address
verification.
To check the IP address:
Home
Print
X
Exit
1
On the Windows Desktop, click Start.
2
Select Run.
3
Type cmd and click OK. A window like the one on the upper left of this page is
displayed.
4
Type ipconfig and press ENTER to display your IP configuration.
5
Type exit and press ENTER to return to the Windows operating system.
31
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Verifying Your IP Address in
Windows 2000
Improper connections between your PC and the SB4200 and cable network problems
are indicated when you receive an Autoconfiguration IP Address. An example is
displayed on the upper left of this page. Check your cabling and whether you can see
your regular cable-TV channels on your television.
After verifying your cable connections and proper operation of the cable-TV system by
looking at the channels on your TV, you can attempt to renew your IP address.
To renew your IP address:
1
Type ipconfig /renew and then press ENTER. If a valid IP address is displayed,
then Internet access should be available.
2
Type exit and then press ENTER to return to Windows.
If after performing this procedure your computer does not access the Internet, call your
service provider. They will assist in your configuration.
Home
Print
X
Exit
32
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Cabling for Multiple Users
Service provider
Your service provider must configure your modem for multiple user service. Contact your
service provider for availability and instructions.
TV cable
SB4200
The SB4200 supports many multiple user configurations. It can easily serve as a
gateway to the Internet for up to 32 users.
Standard
Ethernet
cable
Ethernet hub
Computer
Computer
Ethernet
Standard
Ethernet
cable
Computer
Multiple users must be connected to an Ethernet hub, which should be attached to the
SB4200.
Caution
Do not connect both the Ethernet and USB cables to the same computer.
Multiple computers cannot be connected to the SB4200 through the USB port.
Home
Print
X
Exit
33
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Cabling for Multiple Users
Service provider
Multiple user configurations can include Ethernet and USB connections.
TV cable
Ethernet and USB
SB4200
USB
Ethernet
Computer
For two users on individual computers, connect the USB and Ethernet ports directly to
the SB4200.
Computer
Service provider
Multiple users are supported with a single user attached to the USB port and the
remaining (up to 31) users connected to the Ethernet hub.
TV cable
SB4200
Caution
USB
Ethernet
Do not connect both the Ethernet and USB cables to the same computer.
Computer
HUB
Computer
Home
Computer
Print
Computer
X
Exit
34
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Troubleshooting
This information helps you solve a problem quickly. Before calling your service provider, try pressing the reset button on the rear panel. Resetting
the SB4200 may take 5 to 30 minutes. Your service provider may need to know the status of the front-panel lights.
Problem
Possible Solutions
Green POWER light is off
!
Check that the power cord is properly plugged into the wall outlet and the rear panel
of the SB4200.
!
Check that the electrical outlet is working.
!
If the Standby LED is on, the cable modem is in Standby mode. Press the Standby
button to reconnect Internet service.
!
Press the Reset button.
!
Call your service provider.
Home
Print
X
Exit
35
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Troubleshooting
Problem
Possible Solutions
Cannot send or receive data
!
Check the lights on the front panel. Note the first light from top to bottom that is off.
This light indicates where the error occurred. If the first light that is off is:
Light
Turns off under the following error condition(s):
Receive
During startup, the receive channel is not acquired.
During normal operation, the receive channel is lost.
During startup, the send channel is not acquired.
During normal operation, the send channel is lost.
During startup, the IP registration was not successful.
During normal operations, the IP registration is lost.
The modem may be in standby mode, press the Standby button.
Send
Online
Power
Home
Print
X
Exit
!
If all lights are off except the Standby LED, the cable modem is in Standby mode
and you need to press the Standby button to reconnect to your Internet service.
!
Check that your TV is working if you have cable, and that you have a clear TV
picture. If you are not receiving your regular TV channels, your data service will not
function.
36
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Troubleshooting
Problem
Possible Solutions
Cannot send or receive data (cont’d)
!
Check the coaxial cable at the modem and wall outlet and hand-tighten if necessary.
!
Check the IP address (follow the steps in “Verifying Your IP Address” on page 30);
call your service provider if you need an IP address.
!
Check that the USB or Ethernet cable is attached at the modem and your computer.
!
Check that Acrobat Reader 4.0 is installed and selected.
!
Remove the USB driver using the instructions for a Windows 98 or
Windows 2000/Windows Me computer that appear on the following pages.
Cannot view User Guide CD video
Operating System problems related to
unsuccessful installation of the SB4200 USB
driver
Home
Print
X
Exit
37
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Removing the SB4200 Device Listing
from Windows 98
1
On your Windows Desktop, right-click the Network Neighborhood icon and select
Properties. The Network window is displayed.
2
Select Motorola SurfBoard USB Cable Modem SB4200, as illustrated in the lower
window.
This procedure does not remove the USB driver from your system, it only
removes the device listing from your system.
Home
Print
X
Exit
38
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Removing the SB4200 Device Listing
from Windows 98
Home
Print
X
Exit
3
Click Remove and the Network Dialogue window no longer displays Motorola
SurfBoard USB Cable Modem in the list.
4
Click OK, and the System Settings Change window is displayed.
5
Click No and go to “Removing the USB Driver from Windows 98” on the next page.
39
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Removing the USB Driver from
Windows 98
You now need to start Windows Explorer. Start Explorer by clicking Start and then
selecting Run. In the Run window, type explorer and then click OK. The Exploring
window is displayed as shown on the left.
1
Be sure that the USB cable has been removed from your PC or SB4200 cable
modem.
2
Select your CD-ROM drive. Run the Remove utility from the Motorola SB4200
CD-ROM by double clicking the Remove icon.
The SB4200 uses the same driver as the
SB4100.
Home
Print
X
Exit
40
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Removing the USB Driver from
Windows 98
The SB4200 USB Driver Removal windows are displayed on this page.
3
Click Remove Driver.
4
The removal of the SB4200 USB is now complete.
You may get various messages in this step, depending on the previous
installation. The status messages you receive are informational only.
5
After you have removed the USB device, repeat the Windows 98 USB Installation
procedure to reinstall the SB4200 with a USB device.
If you have problems, please contact your service provider.
Home
Print
X
Exit
41
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Removing the SB4200 Device Listing
from Windows 2000 and Windows Me
1
From your Windows 2000 or Windows Me desktop, click Start.
2
Click Settings.
3
Click the Control Panel icon and the window on the left is displayed.
4
Double-click the Add/Remove Hardware icon. This action starts the Add/Remove
Hardware Wizard as illustrated in the upper window on the next page.
This procedure does not remove the USB driver from your system, it only
removes the device listing from your system.
Home
Print
X
Exit
42
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Removing the SB4200 Device Listing
from Windows 2000 and Windows Me
Home
Print
X
Exit
5
Click Next to continue, and the Choose a Hardware Task window is displayed.
6
Select Uninstall/Unplug a device and click Next.
43
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Removing the SB4200 Device Listing
from Windows 2000 and Windows Me
7
Select Uninstall a device and click Next. The Installed Devices on Your Computer
window is displayed.
8
If you unplugged the USB cable from the SB4200 (and saw the Unsafe Removal of
a Device window), then the SB4200 will probably not be listed as illustrated in the
lower window.
If the device is not listed, then click Cancel. If it is listed, highlight the SB4200 and
click Next.
Home
Print
X
Exit
44
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Removing the SB4200 Device Listing
from Windows 2000 and Windows Me
9
On the upper window on the left, select “Yes, I want to uninstall this device” and click
Next.
10 On the lower window, click Finish.
11 Close the Control Panel Window.
Home
Print
X
Exit
45
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Removing the USB Driver from
Windows 2000 and Windows Me
1
Start Windows Explorer. Click Start and then select Run.
2
In the Run window, type explorer and then click OK.
3
Double-click My Computer.
4
Double-click the Motorola (D:) CD Icon.
5
Double-click the REMOVE OUT USB Icon, as illustrated in the window on the left.
The SB4200 uses the same driver as the
SB4100.
Home
Print
X
Exit
46
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Removing the USB Driver from
Windows 2000 and Windows Me
6
The window on the left is displayed. Be sure that the USB Cable Modem is
disconnected. Click Remove Driver.
Depending on how the device was removed early on in the process, all of the files
may not be shown as Successfully Removed and some of the files may be
displayed as Not Found. If a file displays a status of Not Found, Windows 2000 or
Windows Me removed the file during the Add/Remove Hardware Wizard portion of
this de-installation procedure.
7
Once you have removed the USB device, repeat the Windows 2000 USB
Installation procedure to reinstall the SB4200 with a USB device.
If you have problems, please contact your service provider.
Home
Print
X
Exit
47
Introduction
Before You Begin
The SB4200 uses the same driver as the
SB4100.
Installation
Configuration
Troubleshooting
Legal
Recovery After Installation Errors with
Win98_SE and Windows 98
If you are unable to properly install the SB4200 USB driver or receive an error during the
installation of this driver, then there may be invalid entries in the Windows Device
Manager. Depending on where the error occurred, follow the procedures described in
Example 1 or Example 2 on the pages that follow.
Example 1
Leave the USB cable plugged into the SB4200 and your computer.
Home
Print
X
Exit
1
From the Windows Desktop, right-click the My Computer icon to display a list of
options.
2
Highlight and then click Properties at the bottom of the list, and the System
Properties window is displayed.
48
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Recovery After Installation Errors with
Win98_SE and Windows 98
3
On the System Properties window, click the Device Manager tab.
4
Expand the Universal Serial Bus controllers branch and see if there is an entry for
USB Composite Device. Windows 98 Second Edition may also have two entries
listed as SB4100 USB Cable Modem under Other Devices. Windows 98 may list
two entries as Unknown Devices under Other Devices. These additional entries
are automatically removed when the USB Composite Device is removed.
5
Highlight the USB Composite Device and click Remove.
EXTREMELY IMPORTANT: After removal of the USB Composite Device, remove the
USB cable from the SB4200 and reboot your computer. Follow the installation
instructions starting on page 10 of this User Guide to reinstall the SB4200 USB drivers.
The SB4200 uses the same driver as the
SB4100.
Home
Print
X
Exit
49
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Recovery After Installation Errors with
Win98_SE and Windows 98
Example 2
The SB4200 drivers may have loaded, but no protocol was bound to the adapter. To see
if this is the case:
1
Remove the USB cable from the SB4200.
2
From the Windows Desktop, right-click the Network Neighborhood icon to display
a list of options.
3
Highlight and then click Properties at the bottom of the list. The Network window is
displayed.
4
Click the Configuration tab, highlight the Motorola Surfboard USB Cable Modem
SB4100 entry, and then click Properties.
5
Click the Bindings tab. If TCP/IP is not listed, either add the protocol to the adapter
or remove the entry for Motorola Surfboard USB Cable Modem SB4100.
To remove the entry: In the Network window, highlight Motorola Surfboard USB Cable
Modem SB4100 and then press Remove.
Home
Print
X
Exit
50
Introduction
Before You Begin
The SB4200 uses the same driver as the
SB4100.
Installation
Configuration
Troubleshooting
Legal
Recovery After Installation Errors with
Win98_SE and Windows 98
EXTREMELY IMPORTANT: After removal of the device, restart your computer. Follow
the installation instructions starting on page 10 of this User Guide to reinstall the SB4200
USB drivers.
Note: The Motorola Remove program deletes improper Windows 98, Windows 98
Second Edition, Windows ME, and Windows 2000 entries that may have occurred in the
installation process. The Remove program and the latest drivers are available for
download from the website ftp.surfboard.com. The files are in the following directory:
pub/Downloads/SB_USB_Driver in the file called USB Instructions.zip.
Prior to running the Remove program, unplug the USB cable from the SB4200. The
Remove program performs the same function as the removal of devices performed in
Example 1 and Example 2 above.
Home
Print
X
Exit
51
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Contact Us
For Motorola cable modem customer service, technical support, warranty claims, or
questions about your Internet service connection, contact your cable service provider
For Motorola consumer cable products, education, and support:
http://www.motorola.com/broadband.
Home
Print
X
Exit
52
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Glossary
Coaxial cable (coax)
A type of wire that consists of a center wire surrounded by insulation and then a grounded
shield of braided wire. The shield minimizes electrical and radio frequency interference.
The coaxial cable is the primary type of cabling used by the cable television industry and is
also widely used for computer networks.
DOCSIS
The Data-Over-Cable Service Interface Specifications defines interface standards for cable
modems and supporting equipment.
Expansion slot
An opening in a computer where a circuit board can be inserted to add new capabilities to
the computer. Expansion slots for PCs come in half- and full-size. Half-size slots are also
called 8-bit slots, and full-size slots are called 16-bit slots. PCI expansions slots are always
full-size and connect directly to the PCI bus.
F-type connector
A connector used in the cable television industry that connects coaxial cable to equipment.
IP address
An identifier for a computer or device on a TCP/IP network. Networks using the TCP/IP
protocol route messages based on the IP address of the destination.
MAC address
Media Access Control address. A hardware address that uniquely identifies each node of a
network. The MAC address is used to forward information through a network to its final
destination.
Home
Print
X
Exit
53
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Glossary
MHz
Mega Hertz. A measure of radio frequency - millions of cycles per second. One MHz
represents one million cycles per second.
PCI
Peripheral Component Interconnect. Most PCs today include a PCI bus in addition to a
more general ISA expansion bus.
Splitter
A splitter is a device that divides the signal power from an input cable equally between
two or more signals, each carrying a selected frequency range.
TCP/IP
Transmission Control Protocol/Internet Protocol. A set of protocols that provides the
standards and rules for controlling and managing communications between networks.
VGA
Video Graphics Array. A graphics display system for PCs. All PCs made today support
VGA, and possibly some other more advanced standard.
Home
Print
X
Exit
54
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
FAQs
Got a question? We’ve put together a list of questions customers frequently ask.
Q
What is high-speed cable Internet access?
A
Cable Internet access uses cable television wires instead of telephone lines to tap into the information on the Internet. It’s extremely fast and
affordable, and it doesn’t tie up phone lines for incoming or outgoing calls and faxes.
Q
How fast are cable modems?
A
Cable modems offer Internet access at speeds up to 100 times faster* than a traditional phone modem. A cable modem user can experience
speeds of over 1,000 Kbps. Due to network conditions, such as traffic and the speed of the site you’re visiting, actual download rates may
vary.
Q
Can I still watch cable TV while I’m using my cable modem?
A
Yes, cable television lines are capable of handling the cable TV signal as well as sending and receiving information on the Internet - at the
same time.
* Actual speed will vary. Many network and other factors affect download speeds.
Home
Print
X
Exit
55
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
FAQs
Q
What is DOCSIS?
A
DOCSIS is the industry standard for cable Internet access. This standard is intended to ensure that all DOCSIS cable modems interface with
all DOCSIS-compliant cable systems. Motorola’s SB4200 cable modem is DOCSIS compliant.
Q
If I have a cable modem, can I still use my old 28.8 Kbps or 56 Kbps modem?
A
Sure! Although once you’ve experienced the speed of cable Internet access, you’ll never again want to wait for traditional dial up services.
Q
I have more than one computer. Do I need more than one computer modem?
A
No, not if your computers are connected via a network. The SB4200 is capable of supporting current Internet Connection Sharing technologies. Internet Connection Sharing software enables the user to connect more PCs to the Internet by using the PC containing the SB4200 as a
gateway.
Q
Do I need to change my Internet Service Provider (ISP)?
A
Currently most Internet Service Providers are not set up to handle cable Internet access. Check with your local cable company for your specific information.
Home
Print
X
Exit
56
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
FAQs
Q
Do I need to subscribe to cable TV to get cable Internet access?
A
No, but you will need to subscribe to cable Internet service. Some systems require that you subscribe to basic service before you can get
Internet access and/or offer a discount when you use your own cable modem. Check with your local cable company for specific information.
Q
What does the SB4200 limited warranty cover?
A
Contact your service provider.
Q
What type of technical support is available?
A
For questions about your Internet service, connection, or cable modem call your cable service provider.
Q
What do I do if my modem stops working?
A
Refer to the Troubleshooting section of this User Guide. It has quick tips for diagnosing problems, as well as simple solutions. If you continue
to have problems, call your cable service provider.
Home
Print
X
Exit
57
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Software License
SOFTWARE LICENSE
MOTOROLA SOFTWARE
MOTOROLA, INC.
Broadband Communications Sector
Cable Modem Division
101 Tournament Drive
Horsham, PA 19044
IMPORTANT: PLEASE READ THIS SOFTWARE LICENSE ("LICENSE") CAREFULLY BEFORE YOU INSTALL, DOWNLOAD OR USE ANY
SEPARATE APPLICATION AND/OR USB DRIVER SOFTWARE AND RELATED DOCUMENTATION ("SOFTWARE") PROVIDED WITH
MOTOROLA'S CABLE MODEM PRODUCT (THE "CABLE MODEM"). BY USING THE CABLE MODEM AND/OR INSTALLING, DOWNLOADING
OR USING ANY OF THE SOFTWARE, YOU INDICATE YOUR ACCEPTANCE OF EACH OF THE TERMS OF THIS LICENSE. UPON
ACCEPTANCE, THIS LICENSE WILL BE A LEGALLY BINDING AGREEMENT BETWEEN YOU AND MOTOROLA. THE TERMS OF THIS
LICENSE APPLY TO YOU AND TO ANY SUBSEQUENT USER OF THIS SOFTWARE.
IF YOU DO NOT AGREE TO ALL OF THE TERMS OF THIS LICENSE, (i) DO NOT INSTALL OR USE THE SOFTWARE AND (ii) RETURN THE
CABLE MODEM AND THE SOFTWARE, INCLUDING ALL COMPONENTS, DOCUMENTATION AND ANY OTHER MATERIALS PROVIDED
WITH THE CABLE MODEM, TO YOUR SERVICE PROVIDER FOR A FULL REFUND.
The Software includes associated media, any printed materials, and any "on-line" or electronic documentation. Software provided by third parties
may be subject to separate end-user license agreements from the manufacturers of such Software.
The Software is never sold. Motorola licenses the Software to the original customer and to any subsequent licensee for personal use only on the
terms of this License. Motorola and its 3rd party licensors retain the ownership of the Software.
Home
Print
X
Exit
59
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Software License
You may:
USE the Software only in connection with the operation of the Cable Modem.
TRANSFER the Software (including all component parts and printed materials) permanently to another person, but only if the person agrees to
accept all of the terms of this License. If you transfer the Software, you must at the same time transfer the Cable Modem and all copies of the
Software (if applicable) to the same person or destroy any copies not transferred.
TERMINATE this License by destroying the original and all copies of the Software (if applicable) in whatever form.
You may not:
(1) Loan, distribute, rent, lease, give, sublicense or otherwise transfer the Software, in whole or in part, to any other person, except as permitted
under the TRANSFER paragraph above. (2) Copy or translate the User Guide included with the Software, other than for personal use. (3) Copy,
alter, translate, decompile, disassemble or reverse engineer the Software, including but not limited to, modifying the Software to make it operate
on non-compatible hardware. (4) Remove, alter or cause not to be displayed, any copyright notices or startup message contained in the Software
programs or documentation. (5) Export the Software or the Cable Modem components in violation of any United States export laws.
The Software is not designed or intended for use in on-line control of aircraft, air traffic, aircraft navigation or aircraft communications; or in design,
construction, operation or maintenance of any nuclear facility. MOTOROLA AND ITS 3RD PARTY LICENSORS DISCLAIM ANY EXPRESS OR
IMPLIED WARRANTY OF FITNESS FOR SUCH USES. YOU REPRESENT AND WARRANT THAT YOU SHALL NOT USE THE SOFTWARE
FOR SUCH PURPOSES.
Home
Print
X
Exit
60
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Software License
Title to this Software, including the ownership of all copyrights, mask work rights, patents, trademarks and all other intellectual property rights
subsisting in the foregoing, and all adaptations to and modifications of the foregoing shall at all times remain with Motorola and its 3rd party
licensors. Motorola retains all rights not expressly licensed under this License. The Software, including any images, graphics, photographs,
animation, video, audio, music and text incorporated therein is owned by Motorola or its 3rd party licensors and is protected by United States
copyright laws and international treaty provisions. Except as otherwise expressly provided in this License, the copying, reproduction, distribution or
preparation of derivative works of the Software, any portion of the Cable Modem or the documentation is strictly prohibited by such laws and treaty
provisions. Nothing in this License constitutes a waiver of Motorola's rights under United States copyright law.
This License and your rights regarding any matter it addresses are governed by the laws of the Commonwealth of Pennsylvania, without reference
to conflict of laws principles. THIS LICENSE SHALL TERMINATE AUTOMATICALLY if you fail to comply with the terms of this License.
Motorola is not responsible for any third party software provided as a bundled application, or otherwise, with the Software.
U.S. GOVERNMENT RESTRICTED RIGHTS
The Software, Cable Modem and documentation is provided with RESTRICTED RIGHTS. The use, duplication or disclosure by the Government is
subject to restrictions as set forth in subdivision ©(1)(ii) of The Rights in Technical Data and Computer Software clause at 52.227-7013. The
contractor/manufacturer is Motorola, Inc., Broadband Communications Sector, 101 Tournament Drive, Horsham, PA 19044.
Home
Print
X
Exit
61
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Warranty Information
SURFboard SB4200 CABLE MODEM
Motorola, Inc., Broadband Communications Sector ("Motorola")
Cable Modem Division
101 Tournament Drive
Horsham, PA 19044
What is my warranty? A warranty for this cable modem product ("Cable Modem") and all accompanying application and USB driver software ("Application
Software") is provided by Motorola to your distributor, cable operator or Internet service provider, as applicable. Please contact your cable operator or
Internet service provider ("Service Provider") for details. Motorola does not warrant that any Application Software will perform error free or without bugs.
Motorola's warranty shall not apply: (i) to any Cable Modem or Application Software (collectively, "Product") subjected to accident, misuse, neglect,
alteration, Acts of God, improper handling, improper transport, improper storage, improper use or application, improper installation, improper testing or
unauthorized repair; or (ii) to cosmetic problems or defects which result from normal wear and tear under ordinary use, and do not affect the performance
or use of the Product. Motorola's warranty applies only to a Product that is manufactured by Motorola and identified by the General Instrument ("GI") or
Motorola trademark, trade name or product identification logo affixed to the Product. MOTOROLA DOES NOT WARRANT THIS PRODUCT DIRECTLY TO
YOU, THE END USER. EXCEPT AS DESCRIBED IN THIS SECTION "WARRANTY INFORMATION", THERE ARE NO WARRANTIES OR
REPRESENTATIONS OF ANY KIND RELATING TO THE PRODUCT, EXPRESS, IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR WARRANTY AGAINST INFRINGEMENT.
MOTOROLA IS NOT RESPONSIBLE FOR, AND PROVIDES "AS IS" ANY SOFTWARE SUPPLIED BY 3RD PARTIES.
Home
Print
X
Exit
62
Introduction
Before You Begin
Installation
Configuration
Troubleshooting
Legal
Warranty Information
What additional provisions should I be aware of? Because it is impossible for Motorola to know the purposes for which you acquired this Product or the
uses to which you will put this Product, you assume full responsibility for the selection of the Product for its installation and use. While every reasonable
effort has been made to insure that you will receive a Product that you can use and enjoy, Motorola does not warrant that the functions of the Product will
meet your requirements or that the operation of the Product will be uninterrupted or error-free. Motorola is not responsible for problems caused by the
interaction of the Product with any other software or hardware.
How long does this Limited Warranty last? Contact your Service Provider for details.
What must I do to obtain warranty service? For Motorola Cable Modem customer service, technical support, warranty claims, questions about your
Internet service or connection, contact your Service Provider. ALL WARRANTIES ARE VOID IF THE PRODUCT IS DAMAGED.
THESE ARE YOUR SOLE AND EXCLUSIVE REMEDIES FOR ANY AND ALL CLAIMS THAT YOU MAY HAVE ARISING OUT OF OR IN CONNECTION
WITH THIS PRODUCT, WHETHER MADE OR SUFFERED BY YOU OR ANOTHER PERSON AND WHETHER BASED IN CONTRACT OR TORT.
IN NO EVENT SHALL MOTOROLA BE LIABLE TO YOU OR ANY OTHER PARTY FOR ANY DIRECT, INDIRECT, GENERAL, SPECIAL, INCIDENTAL,
CONSEQUENTIAL, EXEMPLARY OR OTHER DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT (INCLUDING,
WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF INFORMATION OR ANY OTHER
PECUNIARY LOSS), OR FROM ANY BREACH OF WARRANTY, EVEN IF MOTOROLA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. IN NO CASE SHALL MOTOROLA'S LIABILITY EXCEED THE AMOUNT YOU PAID FOR THE PRODUCT.
Motorola's warranty is governed by the laws of the Commonwealth of Pennsylvania, excluding its conflict of laws principles and excluding the provisions of
the United Nations Convention on Contracts for the International Sale of Goods.
Home
Print
X
Exit
63
485646-001-99
8/01
Home
Print
X
Exit
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising