Ryobi | CDR180 | Specifications | Ryobi CDR180 Specifications

Ryobi CDR180 Specifications
CDR180
COMPACT DIGITAL RADIO
OWNER’S OPERATING MANUAL
ORIGINAL INSTRUCTIONS
DESCRIPTION
1.
2.
3.
4.
5.
6.
7.
8.
Digital display
Integrated auxiliary cable
Retainer strap
Touch pad controls
Antenna
Screw
Battery cover
AAA batteries
17. Low battery indicator
18. Tune/seek
19. Clock button
20. Volume up button
21. Volume down button
22. MP3 player (not included)
23. Retainer strap
24. Integrated auxiliary cable
9. Battery compartment
10. Battery pack
11. Battery port
12. Latches
13. On/off button
14. Volume
15. Mode
16. Preset
5
1
4
2
3
Fig. 1
6
12
A
A
A
A
A
A
10
11
9
7
8
Fig. 2
Fig. 3
15
13
16
14
17
18
Fig. 4
19
21
20
Fig. 5
24
23
22
Fig. 6
Important!
It is essential that you read the instructions in this manual before
operating this machine.
Subject to technical modifications.
English
3. PERSONAL SAFETY
a. Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
c. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1. WORK AREA
a. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools
create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. ELECTRICAL SAFETY
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adaptor plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
f. If operating power tools in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
4. POWER TOOL USE AND CARE
a. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that can not be
controlled with the switch is dangerous and must
be repaired.
c. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
1
English
dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits
etc., in accordance with these instructions and
in the manner intended for the particular type
of power tool, taking into account the working
conditions and the work to be performed. Use
of the power tool for operations different from
intended could result in a hazardous situation.
near fire or heat. This will reduce the risk of explosion
and possibly injury.
 Do not crush, drop or damage battery pack. Do
not use a battery pack or charger that has been
dropped or received a sharp blow. A damaged
battery is subject to explosion. Properly dispose of a
dropped or damaged battery immediately.
 Batteries can explode in the presence of a source
of ignition, such as a pilot light. To reduce the risk
of serious personal injury, never use any cordless
product in the presence of open flame. An exploded
battery can propel debris and chemicals. If exposed,
flush with water immediately.
 Do not charge battery product in a damp or wet
location. Following this rule will reduce the risk of
electric shock.
 For best results, your battery product should be
charged in a location where the temperature is
more than 50°F but less than 100°F. To reduce the
risk of serious personal injury, do not store outside or
in vehicles.
5. BATTERY TOOL USE AND CARE
a. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
b. Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
c. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery terminals
together may cause burns or a fire.
d. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
 Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
 To reduce the risk of personal injury and electric
shock, the product should not be played with or
placed where small children can reach it.
 To reduce the risk of electric shock, do not expose
to water or rain.
 Do not use the radio to listen to music or other
audio programs while operating machinery. Doing
so may cause distractions that could result in serious
personal injury.
6. SERVICE
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
 This radio is capable of producing sound levels
that can be dangerous to long-term hearing.
Listening to music at high volume for any period of
time may cause noise-induced hearing loss. The
higher the volume, the less time required before your
hearing may be affected.
SPECIAL SAFETY RULES
 Battery products do not have to be plugged into
an electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery product or when
changing accessories. Following this rule will reduce
the risk of electric shock, fire, or serious personal
injury.
SPECIFICATIONS
 Do not place battery products or their batteries
Voltage
2
18 V
MW tuner
522-1620 KHz
FM tuner
87.5-108.0 MHz
Auxiliary cable
3.5 mm
English
NOTE: This radio is capable of receiving AM (Amplitude
Modulated) and FM (Frequency Modulated) radio signals.
The AM frequency range is 522-1620 KHz or MW (Medium
Wave). The display on the radio will show MW and FM.
battery packs.
BATTERY PROTECTION FEATURES
Ryobi 18 V lithium-ion batteries are designed with features
that protect the lithium-ion cells and maximise battery life.
Under some operating conditions, these built-in features
may cause the battery and the tool it is powering to act
differently from nickel-cadmium batteries.
During some applications, the battery electronics may
signal the battery to shut down, causing the tool to stop
running. To reset the battery and tool, release the trigger
and resume normal operation.
NOTE: To prevent further shut down of the battery, avoid
forcing the tool.
If releasing the trigger does not reset the battery and tool,
the battery pack is depleted. If depleted, the battery pack
will begin charging when placed on a lithium-ion charger.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Model
CDR180
Compatible
battery pack
Compatible charger
BPL-1820
BPL-1815
BCL-1800
BCL1418
BCS618
ABP1801
ABP1802
ABP-1813
ABP-1815
BCL-1800
BCS618
BCL1418
ACR1800
260022029
TO INSTALL/REMOVE AAA BATTERIES (INCLUDED)
See Figure 2.
It is advisable to write down stored frequencies before
replacing the clock batteries.
There is a 15-second time frame for replacing the AAA
batteries. If batteries are not replaced within 15 seconds,
the radio will lose all settings previously stored in memory,
and they will require reprogramming.
OPERATION
WARNING
Always use new alkaline batteries for replacement.
1. Loosen the screw from the battery cover.
2. Remove the battery cover.
3. Install two new AAA batteries according to polarity
indicators inside the battery compartment.
NOTE: Do not mix old and new batteries.
4. Replace the battery cover and secure with the screw.
Do not allow familiarity with products to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict serious injury.
WARNING
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended
can result in serious personal injury.
TO INSTALL/REMOVE BATTERY PACK
See Figure 3.
WARNING
WARNING
Always remove battery pack from the product when
assembling parts, making adjustments, cleaning, or
when not in use.
This radio is capable of producing sound levels that can
be dangerous to long-term hearing. Listening to music
at high volume for any period of time may cause noiseinduced hearing loss. The higher the volume, the less
time required before your hearing may be affected.
To install:
1. Place the battery pack in the radio, aligning the raised
rib on the battery pack with the groove in the radio’s
battery port.
2. Make sure the latches on each side of the battery pack
snap in place and that battery pack is secured in the
radio.
APPLICATIONS
You may use this product for the purposes listed below:
 Listening to MW/FM radio
 Amplifying MP3 players, CD players, and other
audio devices
This product will accept Ryobi One+ 18 V lithium-ion
battery packs and Ryobi One+ 18 V nickel-cadmium
3
English
To remove:
Depress the latches on both sides of the battery pack
to release and remove the battery pack.
MANUAL TUNING
See Figure 4.
The TUNE/SEEK buttons are used to manually tune to
the desired radio frequency. The selected frequency is
displayed on the digital display.
DIGITAL DISPLAY
See Figure 4.
To use tune feature:
The digital display on the front of the radio illuminates when
the radio is switched on, displaying the time or frequency,
and mode. If the battery charge is low, a flashing low
/
battery indicator will also be displayed:
 Press the TUNE/SEEK DOWN button and quickly
release to tune to the next lowest frequency step.
 Press the TUNE/SEEK UP button and quickly release
to tune to the next highest frequency step.
NOTE: Charge battery when low battery indicator begins
to flash. If the radio continues to operate with the low
battery indicator flashing, the radio will drain the battery
until the radio no longer emits sound. To avoid deep
discharge, remove the battery pack from the radio and
charge immediately.
To use seek feature:
 Press and hold TUNE/SEEK DOWN button for one
second to tune to the next lowest frequency with clear
reception.
 Press and hold TUNE/SEEK UP button for one
second to tune to the next highest frequency with clear
reception.
TURNING THE RADIO ON/OFF
See Figure 4.
Press the on/off button to turn the radio on or off.
NOTE: When the radio is off, the time will be shown on the
display even if the 18 V battery is removed after the AAA
batteries have been installed.
To use the antenna:
Raise or lower radio antenna until radio channel can
be heard clearly.
ADJUSTING THE VOLUME
STORING A PRESET IN MEMORY
See Figure 4.
See Figure 4.
When the radio is turned on, it will return to the last volume
setting used.
The memory feature saves up to 20 frequencies as presets
in the radio’s memory. You can save 10 frequencies in FM
mode and 10 in MW mode.
NOTE: If the 18 V battery is removed from the radio or
has no charge, the radio will return to the default volume
setting.
To store a frequency in memory:
 Tune to the frequency you want to save.
To increase the volume: Push the VOLUME UP button.
 Press and hold the PRESET button. A memory
location number will blink on and off.
To decrease the volume: Push the VOLUME DOWN
button.
 Press the TUNE/SEEK UP or TUNE/SEEK DOWN
button to select a memory location.
NOTE: To change volume quickly, hold the VOLUME UP
or VOLUME DOWN button.
MODE SELECTION
 Press the PRESET button to store the frequency in the
selected memory location.
See Figure 4.
To recall a preset frequency:
To switch modes, press the mode button. The selected
mode will be shown in the digital display. There are three
modes:
 Press the PRESET button and quickly release to cycle
through stored frequencies.
 FM mode
SETTING THE CLOCK
 MW mode
See Figure 5.
 AUX mode
Press the CLOCK button to view the time in the digital
display. To return to the frequency view, press the CLOCK
button again.
NOTE: When turned on, the radio will return to the last
mode that was used unless the 18 V battery is removed
or has no charge.
NOTE: In AUX mode, the time is always displayed.
4
English
To set the clock:
MAINTENANCE
 Press the CLOCK button until the time is displayed on
the digital display.
WARNING
 Press and hold the CLOCK button. The number
representing the hours will blink on and off.
When servicing, use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
 Press the VOLUME UP or VOLUME DOWN button to
set the hour.
NOTE: To set the clock to an hour between noon and
midnight, press the VOLUME UP or VOLUME DOWN
button until "PM" appears in the display.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
 Press the CLOCK button. The number representing
the minutes will blink on and off.
WARNING
 Press the VOLUME UP or VOLUME DOWN button to
set the minutes.
Do not at any time let brake fluids, gasoline, petroleum
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
 Press the CLOCK button. The clock is now set.
NOTE: If AAA batteries are removed or lose charge for
more than 15 seconds, clock settings will be lost. Settings
are not affected by the removal of the 18 V battery.
USING MP3 AND CD PLAYERS (NOT INCLUDED)
WARNING
See Figure 6.
Do not abuse power tools. Abusive practices can
damage the tool as well as your workpiece.
 Select AUX mode.
 The retainer strap may be used to secure an MP3
player into position.
WARNING
NOTE: The retainer strap cannot secure CD players.
 Connect the integrated auxiliary cable to the MP3 or
CD player.
Do not attempt to modify this tool or create accessories
not recommended for use with this tool. Any such
alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury.
NOTE: The auxiliary cable cannot be removed from the
radio.
 The CD or MP3 player must be ON and in PLAY mode
for sound to be heard through the speaker.
 All MP3 player controls can be used normally while
connected to the radio.
SYMBOL
NOTE: Volume for any device connected through the
auxiliary connector can be adjusted using the volume
control for that device or with the VOLUME UP or
VOLUME DOWN buttons on the radio.
Safety Alert
V
 Turning the radio OFF will NOT turn the MP3 player
OFF.
Hz
 The integrated auxiliary cable DOES NOT provide
charging function.
W
 For complete operating instructions for all MP3 and
CD players, always refer to the manual that was
included with your model.
min-1
no
Volts
Hertz
Alternating Current
Watts
No-load speed
Revolutions or reciprocations per minute
Double insulation
Recycle unwanted
5
English
Wear ear protection
Wear eye protection
Please read the instructions carefully before
starting the machine.
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
6
TECHTRONIC INDUSTRIES (AUSTRALIA) PTY. LTD.
Level 1. 666 Doncaster Road,
Doncaster, Victoria 3108
Australia.
Tel: 61 3 9840 3226 Fax No.: 613 9840 6133 www.ryobi.com.au
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising