Specifications Sheet 4

Specifications Sheet 4
LED Dimming Driver
Hi-lume® A-Series L3D
Architectural Dimming
369-325 Rev. D
1 10.12.11
Hi-lume® A-Series Driver Overview
EcoSystem® or 3-wire control
Hi-lume® A-Series Driver is a high-performance LED
driver that provides smooth, continuous 1% dimming
for virtually any LED fixture, whether it requires constant current or constant voltage. It is the most
versatile LED driver offered today due to its compatibility with a wide variety of LED arrays, multiple form
factors, and numerous control options.
Features
•Continuous, flicker-free dimming from 100% to 1%.
•Compatible with Energi Savr Node™ with EcoSystem®
unit, GRAFIK Eye® QS control unit, PowPak™
dimming module with EcoSystem®, and Quantum®
systems, allowing for integration into a planned or
existing EcoSystem® lighting control solution. Please
see chart at the end of this document or contact
Lutron for details regarding compatible controls.
•Standard 3-wire line-voltage phase-control technology
for consistent dimming performance and compatibility
with all Lutron® 3-wire fluorescent controls.
•Protected from miswires of input power to
EcoSystem® control inputs.
•100% performance tested at factory.
•100% burned in at factory.
•A rated lifetime of 50,000 hours @ TC = 149 °F (65 °C).
•UL recognized for United States and Canada.
•FCC Part 15 compliant for commercial applications
at 120 V ~ or 277 V ~.
•Pulse Width Modulation (PWM) or Constant Current
Reduction (CCR) dimming methods available. See
Application Note #360 for details.
•For more information please go to:
www.lutron.com/HilumeLED
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Hi-lume® A-Series, case type K
3.00 in (76 mm) W x 1.00 in (25 mm) H x
4.90 in (124 mm) L
Hi-lume® A-Series, case type M
1.18 in (30 mm) W x 1.00 in (25 mm) H x 14.25 in
(362 mm) L
Page 1
LED Dimming Driver
Hi-lume® A-Series L3D
Architectural Dimming
369-325 Rev. D
2 10.12.11
Specifications
Standards
Performance
• Dimming Range: 100% to 1%
• Operating Voltage: 120-277 V ~ at 50/60 Hz
• A rated lifetime of 50,000 hours @ TC = 149 °F (65 °C).
Contact Lutron for derating information.
• Patented thermal foldback protection
• LEDs turn on to any dimmed level without flashing
to full brightness.
• Nonvolatile memory restores all driver settings after
power failure.
• Power Factor: > 0.90 at 40 W
• Standby Power Consumption: < 1.0 W
• Total Harmonic Distortion (THD): < 20% at 40 W
• Inrush Current: < 2 A
• Inrush Current Limiting Circuitry: eliminates circuit
breaker tripping, switch arcing and relay failure.
• Open circuit protected
• Short circuit protected
• Turn-on time: < 1 second
• PWM Dimming Frequency: 550 Hz
Environmental
• Sound Rating: Class A.
• Relative Humidity: Maximum 90% non-condensing.
• Minimum operating ambient temperature
TA = 32 °F (0 °C).
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
• Meets ANSI C62.41 category A surge protection
standards up to and including 4 kV.
• FCC Part 15 compliant for commercial applications
at 120 V ~ or 277 V ~.
• Manufacturing facilities employ ESD reduction
practices that comply with the requirements of
ANSI/ESD S20.20.
• LutronR Quality Systems registered to ISO
9001.2008.
• UL 8750 recognized.
• Class 2 output available.
• Meets LED Driver requirements for Energy Star 1.1.
Driver Wiring & Mounting
• Driver is grounded by a mounting screw to the
grounded fixture (or by terminal connection on the
K case).
• Terminal blocks on the driver accept one solid wire
per terminal from 18 to 16 AWG (0.75 to 1.5 mm().
• Fixture must be grounded in accordance with local
and national electrical codes.
• Maximum driver–to–LED light engine wire length is
10 ft (3.0 m).
Page 2
LED Dimming Driver
Hi-lume® A-Series L3D
Architectural Dimming
369-325 Rev. D
3 10.12.11
How to Build a Model Number: Hi-lume® A-Series
L 3 DA 4U1U _ _ - _ _ _ _ _
Case Size:
example: L3DA4U1UKS-HC070
For further assistance selecting your model
number, contact our LED Center of Excellence
at 1-877-346-5338 or [email protected]
K = Compact
M = Stick
Current Level (for Constant Current):
020 = 0.20 A; 021 = 0.21 A . . . 210 = 2.10 A
Voltage Level (for Constant Voltage):
100 = 10.0 V; 105 = 10.5 V . . . 600 = 60.0 V
Case Style:
S = Studded
(K case only)
N = Non-Studded
Driver Output:
C = Constant current driver
with pulse width modulation (PWM) dimming
A = Constant current driver
with constant current reduction (CCR) dimming
V = Constant voltage driver
with pulse width modulation (PWM) dimming
LED Load Output Range (see the following pages for more detail):
Class 2 Constant Voltage
Class 2 Constant Current
A = 10.0 V–12.0 V
E = 0.20 A–0.50 A 30 V–54 V
Isolated Non-Class 2
Constant Current
B = 12.5 V–20.0 V
F = 0.51 A–1.00 A 30 V–54 V
Y = 0.20 A–0.50 A 30 V–60 V
C = 20.5 V–24.0 V
G = 0.20 A–0.70 A 8 V–20 V
Z = 0.51 A–1.00 A 30 V–60 V
D = 24.5 V–38.0 V
H = 0.20 A–0.70 A 15 V–38 V
I = 0.71 A–1.05 A 8 V–20 V
Isolated Non-Class 2
Constant Voltage
J = 0.71 A–1.05 A 15 V–38 V
X = 38.5 V–60.0 V
L = 1.06 A–1.50 A 15 V–38 V
K = 1.06 A–1.50 A 8 V–20 V
M = 1.51 A–2.10 A 8 V – 20 V
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page 3
LED Dimming Driver
Hi-lume® A-Series L3D
Architectural Dimming
369-325 Rev. D
4 10.12.11
“A” Output Range, Voltage Driver Models
Driver Type
Output Dimming Method
Output Voltage
Output Current
Output Power
Constant Voltage Driver
(Class 2)
Pulse Width Modulation (PWM) 10.0 – 12.0 V
0.42 – 3.3 A
5 – 40 W
Standards Recognition
Voltage Driver Operation Range:
Output Current vs. Output Voltage
Output Current vs. Output Voltage
3.5
3.5
3.3
3.3
Output Power vs. Output Voltage
Output Power vs. Output Voltage
40
40
3
3
2
2
Output
OutputPower
Power(W)
(W)
Output
OutputCurrent
Current(A)
(A)
2.5
2.5
A
A
1.5
1.5
1
1
30
30
25
25
A
A
20
20
15
15
10
10
0.5
0.5
0
0
3.3 A Max.
3.3 A Max.
35
35
5
5
5 W Min.
5 W Min.
10 12
10 12
0
0
20
20
30
30
40
40
50
50
0
0
60
60
0
0
10 12
10 12
20
20
Output Voltage (V)
Output Voltage (V)
30
30
40
40
50
50
60
60
Output Voltage (V)
Output Voltage (V)
Typical Performance Specifications:
Parameter
120 V
240 V
277 V
Test Conditions
TA = 25° C,
12.0 V, 40 W load,
Max. Light Output,
K enclosure
Input Current
390 mA
210 mA
170 mA
Power Factor
0.99
0.97
0.95
THD
14%
17%
16%
Driver Efficiency
81%
83%
83%
Driver Efficiency vs. Output Power at 120 V
Driver Efficiency vs. Output Power at 120 V
85
85
85
85
80
80
80
80
12.0 V
12.0 V
10.0 V
10.0 V
75
75
70
70
65
65
60
60
Driver Efficiency vs. Output Power at 277 V
Driver Efficiency vs. Output Power at 277 V
90
90
Efficiency
Efficiency(%)
(%)
Efficiency
Efficiency(%)
(%)
90
90
12.0 V
12.0 V
10.0 V
10.0 V
75
75
70
70
65
65
5
5
10
10
15
15
20
20
25
25
30
30
35
35
40
40
Output Power (W)
Output Power (W)
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
60
60
5
5
10
10
15
15
20
20
25
25
30
30
35
35
40
40
Output Power (W)
Output Power (W)
Page 4
LED Dimming Driver
Hi-lume® A-Series L3D
Architectural Dimming
369-325 Rev. D
20 10.12.11
K Case: Case Dimensions
C
J*
A
I*
H*
B
E D
F
G
K Case: Connector Location Dimensions
K*
L
O
P
K*
Q
8-32
Threaded
Studs*
L
M
N
Q
A
B
C
D
E
4.20 in (107 mm)
1.00 in (25 mm)
3.00 in (76 mm)
4.90 in (124 mm)
4.60 in (117 mm)
(mounting center)
F
G
H* I* J*
K* 1.42 in (36 mm)
1.99 in (51 mm)
1.11 in (28 mm)
2.00 in (51 mm)
1.60 in (41 mm)
0.33 in (8.3 mm)
R*
L
M
N
O
P
Q
0.65 in (16.5 mm)
0.75 in (19 mm)
1.73 in (44 mm)
1.33 in (34 mm)
0.74 in (19 mm)
0.32 in (8 mm)
R* 0.29 in (7 mm)
* Applies to studded K case only.
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page 20
LED Dimming Driver
Hi-lume® A-Series L3D
Architectural Dimming
369-325 Rev. D
21 10.12.11
K Case: Side Entry Connector Location Dimensions (Non-Studded)
S
U
T
S
T
U
V
1.38 in (35 mm)
0.64 in (16 mm)
0.88 in (22 mm)
1.53 in (39 mm)
V
M Case: Case Dimensions
C
B
A
A
B
C
D
14.125 in (359 mm)
13.68 in (347 mm)
(mounting center)
1.18 in (30 mm)
1.00 in (25 mm)
D
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page 21
LED Dimming Driver
Hi-lume® A-Series L3D
Switched Hot (Black)
+V 3 (Red)
Wiring Diagram for 3-Wire Control
To
3-wire
Dimming
Control
Dimmed Hot (Orange)
Switched Hot (Black)
To
3-wire
Dimming
Control
Neutral (White)
Dimmed Hot (Orange)
Ground1 (Green)
Neutral (White)
Hi-lume®
A-Series
+V 3 (Red)
-V 3 (Black)
2
Hi-lume
®
Ground
A-Series
Architectural Dimming
369-325 Rev. D
22 10.12.11
LED
light
engine
LED
light
engine
-V 3 (Black)
Ground
2
Ground (Green)
1
Wiring Diagram for EcoSystem® Digital Control
Switched Hot (Black)
To
Line
Voltage
To
Line
Voltage
+V 3 (Red)
Neutral (White)
1
Ground
Switched(Green)
Hot (Black)
Hi-lume®
A-Series
+V (Red)
3
Neutral (White)
Ground (Green)
1
-V 3 (Black)
Hi-lume
®
Ground
A-Series
2
LED
light
engine
LED
light
engine
-V 3 (Black)
To
EcoSystem®
Digital Link
E1 (Purple)
Ground2
E2 (Purple)
E1 (Purple)
To
Note:
Colors®shown correspond to terminal blocks on driver.
EcoSystem
E2 (Purple)
Digital Link
Ground wire connection available on K case models only.
Fixture and driver case must be grounded in accordance with local and national electrical codes.
3
Maximum driver–to–LED light engine wire length is 10 ft (3.0 m).
1
2
+V 3 (Red)
Dimmed Hot (Black)
To
Forward Phase
Dimming
Control
To
Forward Phase
Dimming
Control
Neutral (White)
Dimmed Hot (Black)
Ground1 (Green)
Hi-lume®
A-Series
+V (Red)
3
-V 3 (Black)
Ground
Hi-lume
®
A-Series
2
Ground
2
Neutral (White)
Ground (Green)
LED
light
engine
LED
light
engine
-V 3 (Black)
1
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page 22
LED Dimming Driver
Hi-lume® A-Series L3D
Architectural Dimming
369-325 Rev. D
23 10.12.11
Compatible Controls
•Guaranteed performance specifications with the controls listed in the chart below.
•For assistance selecting controls, contact our LED Center of Excellence at 1-877-346-5338 or [email protected]
Product
Part Number
Nova T*®
Nova®
Fixtures per Control1
Measured Light
Output Range
120 V
277 V
120 V
277 V
NTF-10-
NTF-10-277-
1 – 41
1 – 44
100% – 1%
NTF-103P-
NTF-103P-277-
1 – 20
1 – 33
100% – 1%
NF-10-
NF-10-277-
1 – 41
1 – 44
100% – 1%
NF-103P-
NF-103P-277-
1 – 20
1 – 33
100% – 1%
1 – 20
–
100% – 1%
Vareo®
VF-10-
Skylark®
SF-10P-
SF-12P-277-
1 – 20
1 – 33
100% – 1%
SF-103P-
SF-12P-277-3
1 – 20
1 – 33
100% – 1%
DVF-103P-
DVF-103P-277-
1 – 20
1 – 33
100% – 1%
Diva®
DVSCF-103P-
DVSCF-103P-277-
1 – 20
1 – 33
100% – 1%
Ariadni®
AYF-103P-
AYF-103P-277-
1 – 20
1 – 44
100% – 1%
Vierti®
VTF-6A-
1 – 15
1 – 33
100% – 1%
Maestro®
MAF-6AM-
MAF-6AM-277-
1 – 15
1 – 33
100% – 1%
MSCF-6AM-
MSCF-6AM-277-
1 – 15
1 – 33
100% – 1%
Maestro Wireless®
MRF2-F6AN-DV-
1 – 15
1 – 33
100% – 1%
RadioTouch®
RTA-RX-F-
1 – 41
1 – 88
100% – 1%
Spacer System®
SPSF-6A-
SPSF-6A-277-
1 – 15
1 – 33
100% – 1%
SPSF-6AM-
SPSF-6AM-277-
1 – 15
1 – 33
100% – 1%
Lyneo® Lx
LXF-103PL-
LXF-103PL-277-
1 – 20
1 – 33
100% – 1%
RadioRA® 2
RRD-F6AN-DV-
1 – 15
1 – 33
100% – 1%
HomeWorks® QS
HQRD-F6AN-DV
1 – 15
1 – 33
100% – 1%
Interfaces
PHPM-3F-120
1 – 41
–
100% – 1%
PHPM-3F-DV
1 – 41
1 – 88
100% – 1%
GRX-FDBI-16A
1 – 41
1 – 88
100% – 1%
2
PowPak™ dimming Module with RMJ-ECO32-DV-B
EcoSystem
32 per EcoSystem link
100% – 1%
Energi Savr Node™ with
EcoSystem®
QSN-1ECO-S, QSN-2ECO-S
64 per EcoSystem link
100% – 1%
GRAFIK Eye® QS with
EcoSystem®
QSGRJ-_E,
QSGR-_E
64 per EcoSystem link
100% – 1%
Quantum®
Various
64 per EcoSystem link
100% – 1%
1
Fixtures per Control value assumes a 40 W fixture. Number of fixtures may be higher if wattage is less than 40 W and may be lower if
ganged. See control specification submittal sheet for details.
2 For use with 3-wire controls or Commercial Systems, RadioRA ® Systems or Home Systems applications.
NOTE: Contact Lutron Technical Support for derating rules when using wallbox controls on the Hi-lume ® A-Series LED Driver in
multi-gang applications.
For the list of compatible controls, visit lutron.com/HiLumeLED and select “EcoSystem/3-wire Control Report Card.”
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page 23
LED Dimming Driver
Hi-lume® A-Series L3D
Architectural Dimming
369-325 Rev. D
24 10.12.11
EcoSystem® Wiring Diagrams
EcoSystem® Digital Link Overview
GND
NEU
LINE
DH
• The EcoSystem® Digital Link wiring (E1 and E2)
SH
connects the digital ballasts and drivers together to form
E1
E2
a lighting control system.
• Each EcoSystem® Digital Link supports up to 64 digital
ballasts, LED drivers or EcoSystem® Modules (e.g.
Driver Terminals
C5-BMJ-16A, C5-XPJ-16A), 32 occupancy sensors
(64 occupancy sensors with Energi Savr Node™ with
EcoSystem®), 16 daylight sensors, and 64 wallstations
or IR receivers.*
• Sensors do not directly connect to Hi-Lume® A-Series
GND
LED drivers.
NEU
DH
• E1 and E2 (EcoSystem® digital link wires) are polarity
SH
insensitive and can be wired in any topology.
E1
E2
• An Energi Savr Node™ with EcoSystem® unit, GRAFIK
Eye® QS control unit with EcoSystem®, PowPak™
dimming module with EcoSystem®, or Quantum®
Driver Terminals
system provides power for the EcoSystem® Digital Link
To the EcoSystem® Digital Bus and additional drivers
and supports system programming.*
and/or ballasts
• All EcoSystem® Digital Link programming is completed
by using the Energi Savr App for Apple iPad, iPod
Notes
Touch or iPhone mobile digital devices, GRAFIK Eye®
• The EcoSystemR Digital Link Supply does not have
QS with EcoSystem®, PowPak™ dimming module with
to be located at the end of the Digital Link.
EcoSystem®, or Quantum® System.
• EcoSystemR Digital Link length is limited by the wire
gauge used for E1 and E2 as follows:
EcoSystem® Digital Link Wiring
Digital
Bus
LINE
Digital
Bus
• Driver EcoSystem® Digital Link terminals only accept
one 18 to 16 AWG (0.75 to 1.5 mm() solid copper wire
per terminal.
• Make sure that the supply breaker to the Digital Driver
and EcoSystem® Digital Link Supply is OFF when wiring.
• Connect the two conductors to the two Digital Driver
terminals E1 and E2 as shown.
• Using two different colors for E1 and E2 will reduce
confusion when wiring several drivers together.
• The EcoSystem® Digital Link may be wired Class 1 or
IEC/PELV NEC® Class 2. Consult applicable electrical
codes for proper wiring practices.
* PowPak™ dimming module with EcoSystem® provides power for
the EcoSystem® Digital Link and can support 32 digital ballasts, LED
drivers or EcoSystem® Modules, 6 Wireless Occupancy Sensors,
1 Wireless Daylight Sensor, and 9 Pico Wireless Controllers.
Wire Gauge
Digital Link Length
(max)
12 AWG
2200 ft
14 AWG
1400 ft
16 AWG
900 ft
18 AWG
550 ft
Wire Size
Digital Link Length
(max)
4.0 mm(
828 m
2.5 mm(
517 m
1.5 mm(
310 m
1.0 mm(
207 m
0.75 mm(
155 m
Apple, iPad, iPod Touch, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page 24
LED Dimming Driver
Hi-lume® A-Series L3D
Architectural Dimming
369-325 Rev. D
Electricians and Contractors
FACILITIES MANAGERS
Driver Leads
SERVICE
Maximum driver–to–LED light engine wire length is
10 ft (3.0 m).
Warranty
Wiring and Grounding
Driver and lighting fixture must be grounded.
Drivers must be installed per national and local
electrical codes.
LED Load Replacement
For Class 2 rated drivers, the LED load can be
changed while the driver is installed and powered.
Maximum Driver Operating Temperature
Driver case temperature (TC) must not exceed UL
conditions of acceptability in end product.
25 10.12.11
For warranty information, please visit
http://www.lutron.com/TechnicalDocumentLibrary/
Ballast%20and%20Driver%20Warranty.pdf
Replacement Parts
When ordering Lutron® replacement parts please
provide the full model number. Consult Lutron if you
have any questions.
Further Information
For further information, please visit us at
www.lutron.com/hilumeLED or contact our
LED Control Center of Excellence at 1.877.346.5338
or [email protected]
For 50,000 hour lifetime, driver case temperature (TC)
must not exceed 149 °F (65 °C).
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page 25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement