Yamaha | SWK-W10 | Owner`s manual | Yamaha SWK-W10 Owner`s manual

Yamaha SWK-W10 Owner`s manual
UC
English
SWK-W10
Wireless subwoofer kit
Ensemble de caisson de sous-graves
OWNER’S MANUAL
MODE D’EMPLOI
Français
• The name plate is located on the bottom of the unit.
• La plaque signaletique se trouve sur le dessous de l’appareil.
i
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
■ Explanation of Graphical Symbols
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert you to the presence of
uninsulated “dangerous voltage” within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9 Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11 Only use attachments/accessories specified by
the manufacturer.
12 Use only with the cart, stand,
tripod, bracket, or table specified
by the manufacturer, or sold with
the apparatus. When a cart is
used, use caution when moving
the cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the
most out of your equipment by playing it at a safe level. One that lets the sound come through loud and
clear without annoying
blaring or distortion – and, most importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often undetectable until it is too late, Yamaha and the
Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged
exposure from excessive volume levels.
1 En
FCC INFORMATION (for US customers)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may
void your authority, granted by the FCC, to use the product.
2. IMPORTANT:
When connecting this product to accessories and/or
another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow
all installation instructions. Failure to follow instructions
could void your FCC authorization to use this product in
the USA.
3. NOTE:
This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements
provides a reasonable level of assurance that your use of
this product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics Corp.,
U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
This equipment compiles with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the
FCC radio frequency (RF)
Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it should be installed and operated with at least 20 cm and more between the
radiator and person’s body (excluding extremities: hands, wrists, feet and ankles).
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Change or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide slot and fully insert.
This Class B digital apparatus complies with Canadian ICES-003.
2 En
Caution: Read this before operating this unit.
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this sound system in a well ventilated,
cool, dry, clean place and away from direct
sunlight, heat sources, vibration, dust, moisture
and cold. For proper ventilation, allow the
following minimum clearances.
Top: 5 cm (2 in)
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
4 Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this unit
in an environment with high humidity (i.e. a room
with a humidifier) to prevent condensation inside
this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object
may fall onto this unit and/or this unit may be
exposed to liquid dripping or splashing. On the
top of this unit, do not place:
– Other components, as they may cause damage and/
or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
6 Do not cover this unit with a newspaper,
tablecloth, curtain, etc. in order not to obstruct
heat radiation. If the temperature inside this unit
rises, it may cause fire, damage to this unit, and/
or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the
wall outlet, grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than
specified is dangerous and may cause fire,
damage to this unit, and/or personal injury.
Yamaha will not be held responsible for any
damage resulting from use of this unit with a
voltage other than specified.
13 Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
14 When not planning to use this unit for long
periods of time (i.e. vacation), disconnect the AC
power plug from the wall outlet.
15 Be sure to read the “Troubleshooting” section on
common operating errors before concluding that
this unit is faulty.
16 Before moving this unit, disconnect the AC
power plug from the wall outlet.
17 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the
power cable from the outlet, then leave this unit
alone.
18 When using this unit for a long time, this unit may
become warm. Leave this unit alone for cooling.
19 Install this unit near the AC outlet and where the
AC power plug can be reached easily.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
Even if a subwoofer is not connected to this unit, this
unit is not disconnected from the AC power source as
long as it is connected to the AC wall outlet. In this
state, this unit is designed to consume a very small
quantity of power.
Do not use this unit within 22 cm (9 inches) of persons
with a heart pacemaker implant or defibrillator implant.
Be sure to use this product only in the country in where
it was purchased.
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
3 En
■ Introduction
SWK-W10 is a receiver for subwoofer signals
transmitted wirelessly from the transmitting-side
Yamaha product (such as YIT-W10, YSP-5100, and
YSP-4100). By connecting SWK-W10 to your
subwoofer (with internal amplifier) using a
subwoofer cable, you can enjoy received bass sounds
for subwoofer. Also, since the power and volume
level of the subwoofer are controlled in conjunction
with transmitting-side operations (Yamaha “yAired”
technology), this unit provides a simple operation.
■ Using SWK-W10
1 Keep this unit and your subwoofer (with
internal amplifier) unplugged from AC
wall outlets.
2 Set the group ID of this unit to one used
on the transmitting-side Yamaha product.
The group ID is set by using 2 group ID switches.
When you set the group ID to “B2”, set each
switch to “B” and “2”.
■ Included items
Check that you have received all of the following
items.
L / SUBWOOFER
A B
123
GROUP ID
R
AUDIO OUTPUT
AC OUTLET
SWK-W10
A B
123
GROUP ID
GROUP ID switch
OWNER’S MANUAL
y
• For information about the group ID of the
transmitting-side Yamaha product, refer to the
manual supplied with the transmitting-side
Yamaha product.
• If the transmitting-side product is not equipped
with an A/B switch, set the A/B switch of this unit
to “A”.
3 Install this unit on or near your
subwoofer.
When you install this unit on your subwoofer, this
unit may be moved by vibration. In this case,
install this unit elsewhere or fix this unit not to be
moved.
The “
” and “yAired” are trademarks
of Yamaha Corporation.
4 En
4 Connect the cables in the following order.
1 Connect the AUDIO OUTPUT (SUBWOOFER) of
this unit and the input jack of your subwoofer using a
subwoofer cable.
2 Plug the power cable of your subwoofer to the AC
OUTLET terminal of this unit.
3 Plug the power cable of this unit to an AC wall outlet.
7 Turn on the transmitting-side product.
The LED turns to green if a wireless connection
between this unit and transmitting-side product is
established.
Status LED
To AC wall outlet
1
3
L / SUBWOOFER
A B
123
GROUP ID
R
AUDIO OUTPUT
AC OUTLET
This unit
L MONO
L
R
R
INPUT
3
INPUT
2
2
LED
This unit is turned off because the
transmitting-side product is also
turned off. Turn on the
transmitting-side product to turn
on this unit.
Orange
A wireless connection is being
established. Please wait.
Green
A wireless connection is
established properly.
Subwoofer
(with internal amplifier)
Note
• Do not plug a subwoofer which power
consumption is higher than 100 W to the AC
OUTLET terminal of this unit.
Status
Red
5 Turn on the subwoofer.
Note
6 Set the volume of your subwoofer to
about half way and then set the crossover
frequency to the maximum.
VOLUME
MIN
MAX
CROSSOVER/
HIGH CUT
MIN
• If your subwoofer is operable with the remote
control, set the subwoofer’s power management
setting to “Always On” to make the power control
of this unit functions properly.
MAX
Subwoofer
5 En
■ Troubleshooting
Refer to the table below if the unit does not function properly. If the problem you are experiencing is not listed
below, or if the instruction below does not help, contact the nearest authorized Yamaha dealer or service center.
Problem
Cause
Remedy
No sound, or the
status LED does
not light up green.
This unit and transmitting-side
Yamaha product are not connected
since they are set to different groups.
Set both this unit and transmittingside Yamaha product to the same
group.
No sound.
The signals are obstructed because
there is an obstacle between the
transmitting-side product and this unit.
Remove the obstacle.
There is a device (microwave oven,
wireless LAN, etc.) outputting signals
in 2.4 GHz frequency band nearby.
Move this unit away from the device.
If the device is IEEE802.11ncompliant, change the channel setting
of the device so as not to affect the
unit.
The connection between this unit and
your subwoofer is improper.
Check the connection.
The volume is turned down.
Raise the output level of the
subwoofer.
Move this unit to another position.
Adjust the volume control of the
transmitting-side product to turn up
the volume. The subwoofer volume
raises in conjunction with the
operation of the transmitting-side
product.
The wireless connection is unstable for
some reasons.
Unplug this unit from the AC wall
outlet and then plug it again. Check if
the LED status lights green.
The subwoofer is set to the standby
mode when the AC power of the
subwoofer is turned to ON.
Set the subwoofer’s power
management setting so that the
subwoofer power interlocks with the
AC power of the subwoofer.
Set audio setting on the subwoofer to
audio detection mode.
Too low volume.
The volume is turned down.
■ Specifications
Power supply ................................AC 120 V, 60 Hz
Power consumption ........................................... 3 W
Power consumption without wireless
connection........................................1.5 W or less
AUDIO OUTPUT (SUBWOOFER)
.................................................... 2 V/120 Hz or less
AC OUTLET ................................ 100 W maximum
6 En
Turn up the volume or adjust the
crossover frequency on your
subwoofer.
Transmission range ................. Approx. 20 m (66 ft)
(without interference)
Dimensions (W × D × H) excluding projections
........................................... 210 × 53.5 × 120.5 mm
(8-3/8 × 2-1/4 × 4-7/8 in)
Weight............................................. 0.8 kg (1.8 lbs)
* Specifications are subject to change without notice
© 2009 Yamaha Corporation All rights reserved.
Printed in Malaysia
WT66270
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising