Digimerge | DPD34D | Instruction manual | Digimerge DPD34D Instruction manual

Digimerge DPD34D Instruction manual
Polaris Vision3
Day & Night Dome Camera
P/N 01.BMS.11.0071401B
V1.00
INSTRUCTION MANUAL
Polaris Vision3
Day & Night Dome Camera
Vandal Model: DPV34D
Indoor Model: DPD34D
Please read this manual thoroughly before use and keep it handy for future reference.
-i-
-ii-
the
-iii-
FEATURES
All Models Feature:
DPD34D
• 1/3” Sony Ex-View™ II 960H • Indoor Dome Model
• 2.8-10.5mm Varifocal Day/Night Lens F1.4 DC Iris
• Camera Mounting: Surface / Semi-Flush mounting
• Excellent low light performance using Polaris Vision3
DPV34D
• 0.03Lux/F1.2 (Color)
• 0.00002Lux w/Sense-Up at x512
• 700+ TV lines of resolution
• Vandal Dome Model
• 3D Digital Noise Reduction (3D-DNR)
• Camera Mounting: Surface Mounting
• Advanced Shadow Reduction (D-WDR)
• Weatherproof Rated (IP66)
• OSD menu control
• Privacy Masking / Motion Detection
• VIDEO OUT(BNC)
• Operates in 12VDC or 24VAC
• Test Monitor Output (RCA)
SPECIFICATIONS
General
Power source
Power consumption
Minimum Power
Requirement
Image sensor
Total pixels
Scanning system
Scanning frequency
Sync.system
Resolution
Min.illumination
Video output
S/N Ratio
Power input
Video output
Lens mount
Lens
Operating temperature
Operating humidity
DPD34D
DPV34D
DC 12V / AC 24V +10%
2.5Watt Max
191mA DC / 150mA AC
1/3” Sony Ex-View™ II 960H
976 (H) x 494 (V)
2:1 interlace
15.734KHz(H), 59.95Hz(V)
Internal / Line Lock
700+ TV Lines
0.00002 LUX (F1.2) Slow Shutter (x512)
1.0 Vp-p (75 ohm, composite)
more than 50dB (AGC OFF)
2-Pin terminal block (Detachable)
BNC Connector (2nd video RCA)
Fixed mount
2.8 - 10.5mm F1.4 Varifocal DC Auto iris
-10~50°C
0-90% RH
-1-
MEASUREMENTS
97.0 mm
3.82 in
55.5 mm
2.19 in
112 mm
4.4 in
3.4"
87 mm
Ø 0.1"
3.5 mm
40 mm
1.57 in
5.1"
130 mm
3.9"
100.0 mm
Vandal Dome Dimensions
Base hole positions
100°
112 mm
4.4 in
137°
123°
5.1"
130 mm
Indoor Dome Dimensions
27 mm
1.1 in
Underside Base hole positions
39 mm
1.5 in
115 mm
4.5 in
Recess Mount Fitting dimensions
Recess cutout and fitting clearance.
-2-
7 mm
.28 in
PACKING CONTENTS
Indoor Dome package contains the following:
Camera in housing----------------------------------1
Camera Locking screws (PA3 Type)------------2
Instruction guide (This Document)--------------1
Surface & Flush Mounting Templates----------2
RCA - BNC test cable-------------------------------1
Junction Box Plate-----------------------------------1
Mounting screw pack-------------------------------1
Vandal Dome package contains the following:
Camera in housing----------------------------------1 Camera Locking screws (PM4 Type)-----------3
Instruction guide (This Document)--------------1
Surface Mounting Template-----------------------1
RCA - BNC test cable-------------------------------1
Junction Box Plate-----------------------------------1
Mounting screw pack-------------------------------1
Tamper allen key-------------------------------------1
Conduit Key-------------------------------------------1
Locking
Screw
Conduit
Key
Allen Key
Mounting Screws Pack.
3pc 70mm / 2.8in Screws
3pc 30mm / 1.2in Screws
3pc 40mm 1.6in plugs
JUNCTION BOX PLATE
Junction box plate allows fitting of either Vandal dome or
Indoor dome to standard 2S, 4S and Octagon junction
boxes.
Junction Box fitting plate accessories:
Junction Box Fiting plate --------------------------1
2S / 4S plate screws (KM3.5 Type)-------------4
Octagon fitting screws (KM4 Type)--------------2
Base Fitting Screws PWM3-----------------------3
88.9 mm
3.5 in
46.0 mm
1.8 in
Base Fitting
Screw.
Octagon
Screw
2S / 4S
Screw
Base Fitting
Screws
83.3 mm
3.28 in
Screw hole overview
Camera base fitting illustration
-3-
Junction box fitting plate attached to camera
JUNCTION BOX INSTALLATION TYPES
2S FITTING
a. 2S Fitting requires only 2pcs of 2S/4S
screws.
Screws
Cable
Entry
Note: You have a reduced space in which
to hide cables using this type of
installation. Recommended for indoor
dome only.
4S FITTING
a. 4S Fitting requires 2pcs of 2S/4S screws.
Screws
Note: Screws used for the 4S box are larger
compared to those used for the 2S (M4
type). Suitable for both indoor and
vandal domes
Cable
Entry
TWO GANG FITTING
a. Two gang fitting (switch box) requires 4pcs
of 2S/4S screws.
Screws
Note: A two gang provides the most robust
fitting. Suitable for both indoor and
vandal domes.
Cable
Entry
OCTAGON FITTING
a. 4” Octagon fitting requires only 2pcs of
Octagon screws.
Screws
Cable
Entry
Note Screws used for the octagon fitting
are larger compared to those used for
the 2S/4S (M4 type). Suitable for both
indoor and vandal domes
-4-
VANDAL DOME FITTINGS
Pendant Cap - model # MNTV2XPC
Replaces the need for the camera base.
Compatible with ceiling conduit installations
Junction Box Accessory - model # MNTV2XJ
Fits either wall mount and corner mount bracket.
Symmetrical design - reversible for top or bottom
conduit.
Corner Mount bracket - model # MNTV2XR
Can fit either Wall Bracket or Junction Box.
-5-
Wall Mount - model # MNTV2XW
Pole Mount - model # MNTV2XP
Pendant Mount - model # MNTV2XC
INSTALLATION. VANDAL DOME
1) Loosen the three tamper screws using the provided
allen key. Lift the dome cover.
1
Note: If you plan to use conduit fitting, remove conduit
cap using the provided conduit key.
A
B
A
Installation Option 1:
Use holes marked with 'A' when
installing camera base first.
Use short 30mm screws and anchors.
B
Installation Option 2:
Use holes marked with 'B' when
installing complete camera housing.
Use long 70mm screws and anchors.
B
A
Mounting Template
Conduit Key
Allen Key
Method 1 - Direct Attach Install
2a) Use the included mounting template (Installation
Option 2) to mark and pre-drill the required holes.
Remove 2 of the 3 base locking screws. Use 2pc of
the 2.8” screws to mount the camera directly to the
mounting surface.
Remove the 3rd base locking screw and install the 3rd
2.8” screw.
2
a
Go to step
on page 7 to complete installation.
OR
Method 2 - Camera Base Install
2b) Use the included mounting template (Installation
Option 1) to mark and pre-drill the required holes.
Remove the camera base by unscrewing the 3
base locking screws, and turn camera module
approx. 5 degrees counter-clockwise to detach
camera base from the camera module. Install the
base to the correct holes as indicated on the mount
template using the 1.2” screws. Go to step 3a.
Method 3 - Junction Box Install
2c) Attach provided fitting plate to junction box
(see page 4 for details). Remove the camera
base by unscrewing the 3 base locking screws,
and turn the camera module approx. 5 degrees
counterclockwise to detach camera base from
camera module. Install the base to the junction box
using the base attachment screws. Go to step 3a.
b
3
4
a
b
3a) Reinsert camera module into camera base by
aligning the arrow notches on the edge of the
camera module and the camera base (label on
edge of camera module indicates the location
of the arrow notch), and turning camera module
clockwise to lock into place.
3b) Use the 3 base locking screws to secure
camera base to camera module.
Go to step
-6-
4
on page 7 to complete installation.
INSTALLATION. VANDAL DOME
4
4) Remove camera cover by squeezing the back and front
of the cover (as indicated by the arrow indicators) at the
same time and lifting it up and away from the lens.
Arrow
5
5) Insert the included video test cable into the RCA jack and
connect to a test monitor to set up camera.
Video test cable
Zoom
6
Thumb Screw
RCA Jack
Focus
6a) Adjust camera viewing angle and secure into
place by tightening thumb screw using a flat head
screwdriver.
Note: Lens adjustment levers are by default in the
locked position. Turn counter clockwise to unlock.
Tighten levers to secure lens setting.
6b) Adjust lens and OSD as required.
6c) Re-attach the camera cover, using the thumb screw
as a guide, until it snaps into place.
7
7a) Re-attach the dome cover. Align arrows according to the
diagram below to ensure a weatherproof seal.
1
2
1 Arrow on camera base
2 Arrow on camera module (inside camera)
3
3 Arrow on dome cover.
Correct arrow alignment
7b) Use the allen key to tighten the tamper screws.
Note: Make sure dome cover cord does not get caught in
the rubber seal.
-7-
INSTALLATION. INDOOR DOME (Surface Fitting)
1
1a) Press down on the tab marked with an arrow to lift
up the dome cover slightly
b
a
1b) While pressing on tab, twist the dome cover
counter clockwise just a few degrees to release
dome cover from back clips.
Lift off the cover.
Method 1 - Direct Attach Install
2a) Use included mounting template to mark and predrill the required holes. Use included 2.8” screws to
mount the camera directly to the mounting surface.
2
Go to step
a
3
on page 9 to complete installation.
OR
Method 2 - Camera Base Install
2b) Use the included mounting template (Installation
Option 1) to mark and pre-drill the required holes.
Remove the camera base by unscrewing the base
locking screws (indicated by padlock markings)
and turn camera module approx. 5 degrees
counterclockwise to detach camera base from the
camera module. Install the base as indicated using
the 1.2” screws. Go to step 3a.
Method 3 - Junction Box Install
b
3
2c) Attach provided fitting plate to junction box
(see page 4 for details). Remove the camera
base by unscrewing the 3 base locking screws,
and turn the camera module approx. 5 degrees
counterclockwise to detach camera base from
camera module. Install the base to the junction box
using the base attachment screws. Go to step 3a.
a
b
3a) Reinsert camera module into camera base by
aligning the arrow notches, and turning camera
module clockwise to lock into place.
3b) Reinstall the base locking screws. (indicated
by padlock markings)
Go to step
-8-
3
on page 9 to complete installation.
INSTALLATION. INDOOR DOME (Semi-Flush Fitting)
1
1a) Press down on the tab marked with an arrow to lift
up the dome cover slightly
1b) While pressing on tab, twist the dome cover counterclockwise to release dome cover
b
a
2
1c)Remove the camera base by unscrewing the base
locking screws (indicated by a padlock markings)
and turn camera module approx. 5 degrees counterclockwise to detach camera base from the camera
module.
a) Cut semi flush mounting hole into surface using
provided Semi-flush Mount Cut-out Template.
Note: Always cut using the inside line of the cutout
template
b) Insert camera into cutout. Make sure that the
mounting arms are not extended.
b
c) Turn screwdriver clockwise to unlock all of the 3
mounting arms.
c
d) Continue turning clockwise to move mounting arms
down until they make contact with inner mounting
surface.
d
Note: Once mounting arms have made contact with
the inner mounting surface, do not apply too
much pressure to avoid damaging surface.
3
Thumb Screw
Zoom
Focus
a) Remove camera cover by squeezing the back and front of
the cover as indicated by the arrow indicators at the same
time and lifting it up and away from the lens.
b) Insert the included video test cable into the RCA jack and
connect to a test monitor to set up camera. (see page 10).
c) Adjust camera viewing angle and secure into place by
tightening thumb screw using a flat head screwdriver.
Adjust lens and OSD as required.
Note: Lens adjustment levers are by default in the locked
position. Turn counter clockwise to unlock. Tighten
levers to secure lens setting.
4
a) Re-attach the camera cover, using the thumb screw as a guide, until it snaps into place.
b) Reattach dome cover.
-9-
CAMERA ADJUSTMENT
RCA Service Connector
Use supplied RCA - BNC cable
If you require BNC output.
OSD function joystick. Pressing down
on joystick acts as ENTER function.
MENU TREE SUMMARY
EXPOSURE • AUTO
• HIGH LUMINANCE • MODE • BRIGHTNESS • LOW LUMINANCE • AGC MAX
• DSS MAX
• MANUAL
• MODE • SHUT • AGC
PIC ADJUST • MIRROR • DIS • EZOOM • LEVEL • SHARPNESS • HUE • B-GAIN • R-GAIN
• ZOOM • PAN • TILT
WHITE BAL • ATW
• SPEED • DELAY CNT • ATW FRAME • ENVIORNMENT
• PUSH • USER1/USER2 • ANTI CR • PUSH LOCK
• B-GAIN • R-GAIN
WDR • MODE • LEVEL • HLC • CLIP LEVEL • SCALE • BLC
DNR • DNR MODE • LEVEL
DAY / NIGHT • AUTO
• BURST • DELAY CNT • DAY> NIGHT • NIGHT> DAY
• BW • COLOR • EXT
• SMART IR
• MODE • LEVEL • GAMA OPT
PRIVACY • AREA SEL • MODE • POSITION • COLOR • TRANSP • MOSAIC
MOTION DET• MOTION DET • DETECT SENSE • BLOCK DISP • DETECT AREA
• MONITOR AREA
OTHERS
• LANGUAGE • LENS
• AUTO • MANUAL
• TYPE • MODE • SPEED
• SYNC • CAMERA TITLE • WPC • VERSION • CAMERA RESET
-10-
CAMERA ADJUSTMENT
OSD MENU control
Press down on the function joystick to access the setup menu. Joystick has 4
directional buttons. Press down on the middle of the joystick to select menu
options.
• Main setup menu is displayed on the monitor screen.
SETUP MENU
SETUP MENU
EXPOSURE
PICT ADJUST
WHITE BAL
WDR
DNR
DAY/NIGHT
PRIVACY
MOTION DET
OTHERS
EXIT
AUTO

ATW


AUTO



SAVE ALL
Select functions by moving the joystick up and down. Move the joystick left and
right to change setting values. Press on joystick to confirm selection.
If a menu option features a  , a sub menu is available which can be accessed
by pressing down on the joystick.
Once you have finished updating settings, highlight SAVE ALL and press down on
the joystick. Then, highlight EXIT and press down on the joystick. If you do not
select SAVE ALL, settings changes will be lost when the camera is rebooted.
-11-
CAMERA ADJUSTMENT
EXPOSURE
SETUP MENU
EXPOSURE
PICT ADJUST
WHITE BAL
WDR
DNR
DAY/NIGHT
PRIVACY
MOTION DET
OTHERS
EXIT
AUTO

ATW


AUTO



SAVE ALL
Changes the output exposure settings a choice of AUTO(default) or MANUAL.
• AUTO
AUTO SETUP
HIGH LUMINANCE
MODE
AE+AUTO IRIS
032
BRIGHTNESS
LOW LUMINANCE
MODE
AGC>DSS
098
AGCMAX
DSS MAX
X4
RETURN
HIGH LUMINANCE
MODE:
BRIGHTNESS:
LOW LUMINANCE
MODE:
AGCMAX:
DSS MAX:
AE+AUTO IRIS / ME+AUTO IRIS
000-255
Brightness level of operating mode as set above.
Default setting is 128
AGC/ SLOW / AGC-DSS / AGC-DSS-AGC / OFF
Settings available only when using DC lens.
000-255
Brightness level of operating mode as set above.
Default setting is 098
X1-512
-12-
CAMERA ADJUSTMENT
MANUAL SETUP
MODE
SHUT
AGC
SHUT
1/60 (S)
6
(DB)
RETURN
• MANUAL
MODE:
SHUT / SLOW
Lets you select combination of exposure modes.
SHUT:
When MODE is set to SHUT, select shutter speed in x / second
1/60 ,1/100, 1/250,1/500,1/1000,1/2000,
1/4000,1/10000
Default setting is 1/60
SHUT:
When MODE is set to DSS
The shut speed can be 2,4,8,16,32,64,128,256
Default setting is 2
AGC:
Set a fixed gain value for the AGC db
6,12,18,24,30,36,42,44.8
-13-
CAMERA ADJUSTMENT
PICT ADJUST
SETUP MENU
EXPOSURE
PICT ADJUST
WHITE BAL
WDR
DNR
DAY/NIGHT
PRIVACY
MOTION DET
OTHERS
EXIT
Picture and display control settings
AUTO

ATW


AUTO



SAVE ALL
PICT ADJUST
MIRROR
DIS
EZOOM
LEVEL
SHARPNESS
HUE
R-GAIN
B-GAIN
OFF
OFF

032
009
042
104
176
RETURN
• MIRROR:
OFF/V-FLIP/H-FLIP/HV-FLIP Horizontally and vertically flip the display output.
ON / OFF Enable/Disable Digital Image Stabilization.
• DIS:
• EZOOM
EZOOM SETUP
000
512
256
ZOOM
PAN
TILT
RETURN
-14-
CAMERA ADJUSTMENT
ZOOM:
PAN:
TILT:
000-255 Default 0
000-1023 Default 512
000-512 Default 256
Note: Zoom must be higher than 0 to use Pan and Tilt settings.
• LEVEL:
000-063 Screen brightness.
• SHARPNESS:
000-015 Screen sharpness.
• HUE: 000-100 Adjust the HUE value
• R-GAIN:
000-255 Adjust the RED gain.
• B-GAIN:
000-255 Adjust the BLUE gain.
WHITE BAL
SETUP MENU
EXPOSURE
PICT ADJUST
WHITE BAL
WDR
DNR
DAY/NIGHT
PRIVACY
MOTION DET
OTHERS
EXIT
AUTO

ATW


AUTO



SAVE ALL
White Balance can be set to following:
ATW / PUSH / USER1 / USER2 / ANTI CR
/ PUSH LOCK
• ATW (Auto Trace White Balance)
ATW SETUP
SPEED
DELAY CNT
ATW FRAME
ENVIORMENT
x0.5
INDOOR
002
002
RETURN
SPEED:
DELAY CNT:
000-255 Specifies the AE control for ATW
Default setting is 239
000-255 Sets the time based of ATW
change. Default setting is 16
-15-
CAMERA ADJUSTMENT
ATW FRAME:
ENVIRONMENT:
x0.50 / x1.00 / x1.50 / x2.00
Sets pull in frame for magnification
Default setting is X0.50
INDOOR / OUTDOOR
Set the pull in frame of ATW
Default setting is OUTDOOR
• PUSH
Use white balance regardless of the subject conditions.
• USER1/2
User defined Blue and Red gain adjustment
USER2 WB
USER1 WB
029
034
B-GAIN
R-GAIN
B-GAIN
R-GAIN
045
038
RETURN
RETURN
B-GAIN:
R-GAIN:
000-255 B Gain adjustment for WB
000-255 R Gain adjustment for WB
• ANTI CR
• PUSH LOCK
Activates color rolling suppression.
Press down on joystick to set current scene as the white balance level. Place a 18% gray card in front of the lens and select PUSH LOCK for a natural white level.
-16-
CAMERA ADJUSTMENT
WDR
SETUP MENU
EXPOSURE
PICT ADJUST
WHITE BAL
WDR
DNR
DAY/NIGHT
PRIVACY
MOTION DET
OTHERS
EXIT
Wide Dynamic Range.
WDR SETUP
MODE
LEVEL
HLC
CLIP LEVEL
SCALE
BLC
AUTO

ATW


AUTO



SAVE ALL
OFF
OFF
OFF
000
010
RETURN
• MODE:OFF / D-WDR
E: OFF / D-WDR
D-WDR: Gamma curve, high & low luminance adjusted
Default is Off
HLC: OFF / ON / AUTO Highlight compensation.
CLIP LEVEL: 000-255 Clipping level. Default setting is 0
SCALE: 000-015
BLC: OFF / ON BLC can be enabled with WDR OFF only
DNR
SETUP MENU
EXPOSURE
PICT ADJUST
WHITE BAL
WDR
DNR
DAY/NIGHT
PRIVACY
MOTION DET
OTHERS
EXIT
AUTO

ATW


AUTO



SAVE ALL
Digital Noise Reduction.
This function reduces the background noise in a low luminance environment.
-17-
CAMERA ADJUSTMENT
DNR
DNR MODE
LEVEL
3D
LOW
RETURN
• DNR MODE:
2D+3D / 3D / 2D / OFF
LEVEL:
Noise reduction Filter mode.
OFF/LOW/MIDLOW/MID/MIDHIGH/HIGH
Adjustment of the filter strength.
Default setting is LOW
DAY/NIGHT
AUTO / BW  / EXT /COLOR 
SETUP MENU
EXPOSURE
PICT ADJUST
WHITE BAL
WDR
DNR
DAY/NIGHT
PRIVACY
MOTION DET
OTHERS
EXIT
AUTO

ATW


AUTO



SAVE ALL
Day/Night mode can be set to the following options: COLOR/AUTO/EXT/BW.
Select COLOR for a color image or BW for black and white. EXT allows the use of
an external trigger to activate day/night operation. Use AUTO to have the camera
automatically adjust for Day/Night mode.
DAY/NIGHT
BURST
DELAY CNT
DAY - NIGHT
NIGHT - DAY
OFF
RETURN
-18-
003
002
005
CAMERA ADJUSTMENT
• AUTO
BURST:
DELAY CNT:
DAY - NIGHT:
NIGHT - DAY:
ON / OFF
Selects whether to output the burst
signal when night mode has been identified.
000-255
Night/Day identification transfer time.
000-255
Threshold for Night status from day status.
000-255
Threshold for the Day status from night
status.
• BW SETUP:
Allows additional Smart IR settings to be enabled.
B/W SETUP
SMART IR
SMART IR SETUP
ON
MODE
LEVEL
GAMA OPT
015
RETURN
RETURN
MODE:
AUTO
ON
AUTO / CENTER
SMART IR AREA
001
009
001
017
TOP
BOTTOM
LEFT
RIGHT
RETURN
Center option under mode allows the user to define a rectangular area
for the Front Light Compensation.
-19-
CAMERA ADJUSTMENT
PRIVACY
OFF / ON
SETUP MENU
EXPOSURE
PICT ADJUST
WHITE BAL
WDR
DNR
DAY/NIGHT
PRIVACY
MOTION DET
OTHERS
EXIT
AUTO

ATW


AUTO



SAVE ALL
Hide an area so that it is not displayed on the monitor.
PRIVACY
AERA SEL
MODE
POSITION
COLOR
TRANSP
MOSAIC
1 / 15
OFF
-
RETURN
AREA SEL: MODE:
Select the privacy area to be adjusted.
OFF / ON
When ON the settings below can be changed
Default OFF for all Areas
PRIVACY
AREA SEL
MODE
POSITION
COLOR
TRANSP
MOSAIC
1 / 15
ON

WHITE
1.00
-
RETURN
-20-
CAMERA ADJUSTMENT
POSITION:
When selected area selection screen appears:
NEXT: PUSH ENTER
Move the joystick to move the corners (you can create any 4-sided shape).
The selected side is highlighted by a small box. To select the next corner,
press ENTER. To return to privacy menu, press enter repeatedly.
COLOR: BLACK, RED, GEEEN, BLUE, YELLOW, CYAN, MAGENTA,
WHITE. Sets the colors of the mask frames.
TRANSP: 1.00 / 0.75 / 0.50 / 0.00 Sets the privacy area transparency.
MOSAIC: ON/OFF Sets the privacy mask as mosaic.
MOSAIC is not available if TRANSP is 1.00
MOTION DET
SETUP MENU
EXPOSURE
PICT ADJUST
WHITE BAL
WDR
DNR
DAY/NIGHT
PRIVACY
MOTION DET
OTHERS
EXIT
AUTO

ATW


AUTO



SAVE ALL
The motion detection areas of the screen are broken into 24 x 16 rectangular
blocks. Use MONITOR AREA to configure always-on motion alert areas on the
screen.
-21-
CAMERA ADJUSTMENT
MOTION DET
MOTION DET
DETECT SENSE
BLOCK DISP
DETECT AREA
MONITOR AREA
OFF
OFF


111
RETURN
MOTION DET:
DETECT SENSE:
BLOCK DISP: DETECT AREA:
OFF / ON. Turn on or off the motion detection.
Default is OFF
0-127 Sets the motion detection sensitivity level.
ON/OFF: Displays blocks in areas where motion is
detected.
Select area of the screen to enable / disable motion
detection.
DETECT AREA
Grid areas: Motion detection enabled
Transparent: Motion detection disabled
EXIT: HOLD ENTER
By default the entire area is enabled for detection. Using the movement arrows
you move the 2x2 size block positions around the screen. Press the enter button
to toggle this area to enable/diable motion detection. Hold down the enter button
to return to the motion detection menu.
-22-
CAMERA ADJUSTMENT
MONITOR AREA :
Allows you to configure up to 4 motion detection areas. Areas will be highlighted
on the screen and flash when motion is detected within them. Areas will not flash
if motion is detected in areas that have been disabled using DETECT AREA.
MONITOR AREA
AERA SEL
MODE
TOP
BOTTOM
LEFT
RIGHT
1/4
OFF
000
000
000
000
RETURN
AREA SEL:
1/4, 2/4, 3/4, 4/4
Select area to adjust.
When enabled, the box colors are:
1 Pink, 2 Green, 3 Blue, 4 Yellow
When areas overlap, the area with the lowest number takes priority
MODE:
TOP:
BOTTOM:
LEFT:
RIGHT:
OFF / ON. 000-015
000-015
000-023
000-023
Disable / Enable area
Position of the top of the area
Position of the bottom of the area
Position of the left side of the area
Position of the right side of the area
Note: TOP value cannot be greater than BOTTOM, and LEFT cannot be greater
than RIGHT. Numbers automatically update to prevent invalid positions.
-23-
CAMERA ADJUSTMENT
OTHERS
SETUP MENU
EXPOSURE
PICT ADJUST
WHITE BAL
WDR
DNR
DAY/NIGHT
PRIVACY
MOTION DET
OTHERS
EXIT
AUTO

ATW


AUTO



SAVE ALL
Miscellaneous camera functions.
OTHERS
LANGUAGE
ENGLISH
LENS
AUTO
SYNC
INT
CAM TITLE
OFF
WPC

VERSION

CAMERA RESET
RETURN
• LENS
MANUAL / AUTO 
AUTO IRIS
TYPE
MODE
SPEED
DC
AUTO
064
RETURN
MODE:
SPEED:
AUTO,OPEN,CLOSE
Sets the mechanical iris control mode.
000-255
Sets the convergence speed of the mechanical iris.
-24-
CAMERA ADJUSTMENT
• CAM TITLE OFF / ON
Select a camera title to be shown on the screen.
CAMERA TITLE SETUP
CAMERA
ABCDEFGHIJKLMNOPQRSTUV
WXYZ0123456789-!#$%&’
()_`.:;<=> @^*./^*X+/
CHR1 CHR2
 CLR POS
RETURN
Use Up/Down/Left/Right to move around. CLR will clear info. POS allows you to
change the title position.
• WPC (Advanced function; not for normal use)
WPC
PLEASE COVER THE LENSENTER PW
RETURN
The WPC (White Pixel Compensation) features is used to correct the CCD if dead
pixels are visible. You must cover the lens completely so no light can enter the
camera sensor for WPC to work. Press the Up,Down, left, right, middle button to
start the highlight of compensation. When prompts finish, press the middle button
to exit.
-25-
CAMERA ADJUSTMENT
• VERSION
Gives version information regarding current camera
software.
VERSION INFO
MCU VER
ROM VER
V1.0.0 NORMAL
V1.0.0
RETURN
• CAMERA RESET 
This will reset all settings for all menus to manufacturer
defaults.
EXIT / SAVE ALL
SETUP MENU
EXPOSURE
PICT ADJUST
WHITE BAL
WDR
DNR
DAY/NIGHT
PRIVACY
MOTION DET
OTHERS
EXIT
AUTO

ATW


AUTO



SAVE ALL
• EXIT
Exit OSD menu.
Exit will keep any changes only until camera is powered off.
• SAVE ALL
Saves the settings to camera
Settings are retained after camera power loss.
-26-
TROUBLESHOOTING
Follow the steps below if you are experiencing trouble with your camera.
Contact Digimerge Technical Support if the issue persists.
• Nothing appears on the screen.
¤¤ Check that the power cable is connected properly and that the voltage is correct.
¤¤ Check that you have properly connected VIDEO cable to the camera VIDEO output jack and to
the monitor/DVR.
• The image on the screen is unclear.
¤¤ Is the lens or dome cover stained with dirt? Clean lens or dome cover with soft, clean cloth.
¤¤ Re-position the camera if necessary.
¤¤ Adjust the Zoom and Focus screws as needed.
• The image on the screen is dark.
¤¤ If you have an intermediate device, set the impedance to 75Ω / Hi-z.
¤¤ Adjust the monitor contrast & brightness controls.
• Image quality is poor.
¤¤ Return the camera OSD to factory default settings (OSD Menu>OTHERS>CAMERA RESET).
¤¤ Verify that the camera is receiving sufficient power.
• There is interference in the image.
¤¤ The camera or the cables may be close to a source of high voltage, such as a generator. Reposition the camera if necessary.
When the resistance value of copper wire is at [20˚C(68˚F)]
Copper wire size (AWG)
Resistance (Ω/m)
Voltage Drop (V/m)
#24(0.22mm2)
0.078
0.028
#22(0.33mm2)
0.050
0.018
#20(0.52mm2)
0.030
0.011
#18(0.83mm2)
0.018
0.006
As shown in the table above, voltage decreases as the wire gets longer. Therefore use of an
excessively long adapter output line for connection to the camera may affect the performance of
the camera.
*Standard voltage for camera operation : DC12V ±10% or AC24V ±10%
*There may be some deviation in voltage drop depending on the type of wire and the
manufacturer.
• Be sure to connect power only after all the installation is complete.
• Use the UL listed, CLASS 2 power transformer for 12v DC or 24v AC adapter.
-27-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising